Monitor and control the sensors through network. supported OPTEX FA CO., LTD. Remote controlling of fiber sensors. Reduces wires and saves space

Transcription

1 CC-Link Communication Unit * FASTUS is a product brand of Optex FA. Monitor and control the sensors through network supported Remote controlling of fiber sensors Reduces wires and saves space OPTEX FA CO., LTD.

2 Solves various problems at production site efficiently through network. supported Easy programming Easy tuning Easy Backup & restore MELSEC-Q series doesn t support CC-Link Communication Unit CC-Link Communication Unit It can get multiple fiber sensor amplifier D3RF series connected to CC-Link. Monitoring, setting and backup of settings are remotely available through network. By connecting fiber sensor amplifier D3RF series, accessibility is drastically improved even if the amplifier is installed in a complex machinery. High speed fiber sensor amplifier D3RF series Fiber cable NF series

3 Supports Mitsubishi Electric iq Sensor Solution You can access to D3RF amplifiers through CC-Link net work remotely and you can control D3RF amplifiers by Mitsubishi "GX Works2". It will release your burden of setting up pushing buttons on the D3RF amplifiers. [Example] What you can do with 1. You can get information of the sensors connected including number of the sensors. 2. Monitoring level of receiving light and/or measurement value of the sensors. 3. Reading out and/or writing settings of the sensors. 4. Backup and/or restore of the settings of the sensors. Reading out information of the sensors including number of the sensors. What you can do; 1. Reading out / Writing of settings 2. Monitoring how the sensors are working 3. Backup and or restore of the settings

4 For improving traceability and maintainability Finding out which sensor works wrongly in a complex machinery may take long time which causes downtime. By connecting all sensors used in the production line to CC-Link network, you will be able to improve traceability and maintainability drastically. If you had replacement of defective sensors in the production line, you will be able to re-setup all sensors in a short period through the network very easily using stored data in the PC through the network previously. Before: setting one by one manually With UC1: controlling sensors on PC You can backup setting parameters of sensors in the SD memory card and restore the data into sensors from the SD memory card on the PLC. You don t have to bring a PC into production site and it won t take long time. You can minimize downtime by utilizing this feature. SD memory card

5 Remote monitoring of sensors You can monitor received light amount of the sensor and measurement value etc. remotely and then will be able to find out what causes the malfunction of the equipment on the production line very quickly through network without going into production site. Reducing wires and saving space Only 2 cables including power supply cable and CC-Link cable are needed. You can save time to wire sensors and also save space for wiring. Conventional wiring With UC1 CC-Link cable No wires!! Wires are needed for every sensors Power supply cable

6 Specifications Model UC1-CL11 CC-Link specifications CC-Link version No. of occupied stations Station type Ver /3/4 (switches automatically according to no. of connected units) Remote device station Baud rate 156 kbps 625 kbps 2.5 Mbps 5 Mbps 10 Mbps Overall length 1,200 m 600 m 200 m 150 m 100 m No. of D3RF amplifier Up to 16 units Indicators Power indicator (green), Status indicator (green), Communication indicator (green), Error indicator (red) Switches Station number setting Communication speed 0 to 9 rotary switch 2 0 to 9 rotary switch 1 Interconnection connector type Dedicated 5-pin connector Power rating Power supply voltage Current consumption 12 to 24 VDC, including ±10% ripple (p-p) 160 ma or less (at 12 V) Environmental resistance Protection circuit Protection category Operating Storage temperature/humidity Vibration resistance Shock resistance Reverse connection protection IP50-25 to +55 C/35 to 85%RH (no condensation or freezing) -40 to +70 C/35 to 95%RH (no condensation or freezing) 10 to 55 Hz; double amplitude 1.5 mm; Approx. 50 G (500 m/s2), 3 times in each X, Y, and Applicable regulations EMC compliant (2004/108/EC); RoHS compliant (2011/65/EU) Applicable standards EN , EN (Group 1, Class A ) Material Polycarbonate Weight Main unit: Approx. 90 g (incl. connector); Packaged: Approx. 155 g *The maximum number of connectable units varies according to the operating temperature. Operating temperature ( C) -25 to 55 C -25 to 50 C -25 to 45 C No. of connectable D3RF series 1 to 3 4 to 8 9 to 16 Dimensions Indicator lamp CC-Link connector Connector for Inter connection Baud rate switch Station No. switch Power supply connector Specifications are subject to change without prior notice. Specifications and technical information not mentioned here are written in Instruction Manual. Or visit our website for details. All the warnings and cautions to know prior to use are given in Instruction Manual Kyoto, Shimogyo, Chudoji Awata 91, Japan TEL FAX