Odin Extension Table Collection Designed by Norm Architects

Transcription

1 Designed by Norm Architects Customer Service: inside the U.S outside the U.S. Round Table Rectangular Table CARING FOR HARDWOOD: To maintain the finish on the table, wipe up spills as soon as possible, and always use placements and coasters. Because dust can be abrasive, use a dry, soft, lint-free cloth when dusting. Occasionally wipe with a very lightly dampened soft cloth and mild detergent, and then dry with a lint-free cloth immediately. No more than twice a year, polish the tabletop by applying wax sparingly with a clean, soft cloth working in the direction of the grain. Do not use spray polish, which contains silicones that will build up over time and ruin the finish. When only parts of the table are in direct sunlight, move occasionally to even out exposure. For the same reason, leave the center leaf in place when possible to expose all parts of the tabletop consistently. Wood is a natural material susceptible to expansion and contraction caused by fluctuations in temperature and humidity. Due to its nature, it may develop minute splits that open and close during seasonal changes, which is perfectly normal. To avoid excessive splits, we recommend situating the table away from direct sunlight, heaters, air conditioners and all other sources of extreme temperatures. WWW. D W R. C O M DESIGN WITHIN REACH STUDIOS

2 Hardware SHORT BOLT - 50MM (x8) LONG BOLT 80mm (x4) WASHERS (x12) ALLEN WRENCH (x1) 2 WWW. D W R. C O M DESIGN WITHIN REACH STUDIOS

3 Leg Attachment 1. With the tabletop face down on a blanket or soft surface, insert the leg assemblies into slots on the apron, being sure the bolt holes in the assemblies are facing toward the middle of the table. Using the Allen wrench, bolt legs in place with two long bolts with washers per assembly, leaving the bolts slightly loose to ensure holes for the short bolts line up. Next, insert four short bolts with washers per assembly, and fasten all bolts securely. LONG BOLT ATTACH 1st WASHER WASHER SHORT BOLT ATTACH 2nd 2. With a helper, carefully lift the table off the ground, turn it right-side up, and place it in the desired location. Lift the table by its long sides, near the seam in the tabletop, where there is the most support. Do not lift the table by its short sides. 3 WWW. D W R. C O M DESIGN WITHIN REACH STUDIOS

4 Opening Leaf Extension 3. After ensuring locks on the underside of the table are in the unlocked position, stand at one end and pull the tabletop to expose the leaf assembly. Hinges Leaf Closed Side View Handle Cleat (not for use as a handle) Leaf Open Side View 4. Standing on the side of the table with the tubular hinge closest to you, grasp the handle firmly, and begin carefully pulling the leaf toward you. Handle Hinge 4 WWW. D W R. C O M DESIGN WITHIN REACH STUDIOS

5 Opening Leaf Extension 5. Slowly continue to pull the leaf toward you as it opens. 6. Support the leaf as it begins to open fully and rest on the tabletop. Push tabletop closed, and lock the locks underneath the tabletop. 5 WWW. D W R. C O M DESIGN WITHIN REACH STUDIOS

6 Closing Leaf Extension 7. After ensuring locks on the underside of the table are in the unlocked position, stand at one end and pull the tabletop to separate leaf. 8. Standing on the side of the table with the handle and DWR nameplate, slowly lift the leaf. 6 WWW. D W R. C O M DESIGN WITHIN REACH STUDIOS

7 Closing Leaf Extension 9. Grab the handle on the underside of the leaf as it begins to close. Sides of the handle should be angled outward to provide a firm grip. If they are angled inward, move to the other side of the table. 10. Grabbing the handle, slowly lower the leaf while reaching across the table. When the leaf is fully closed, push tabletop closed, and lock the two locks underneath the tabletop. 7 WWW. D W R. C O M DESIGN WITHIN REACH STUDIOS