Beer Complet. Project from

Transcription

1 Beer Complet Project: Beer Complet Page 1 of 57 Carefully make the items by following the measurements given on particular pictures. The measurements are given in millimeters, while the measurements given in inches are in brakes (1 inch = 25, 4 mm). You can use various types of wood, but we recommend birch, cedar, walnut, beech, maple or alder.

2 Subassembly List Project: Beer Complet Page 2 of 57

3 Project: Beer Complet Page 3 of 57 Table Parts List

4 Project: Beer Complet Page 4 of 57 Table 2D Documentation

5 Project: Beer Complet Page 5 of 57

6 Project: Beer Complet Page 6 of 57

7 Project: Beer Complet Page 7 of 57

8 Project: Beer Complet Page 8 of 57

9 Project: Beer Complet Page 9 of 57

10 Project: Beer Complet Page 10 of 57

11 Project: Beer Complet Page 11 of 57

12 Project: Beer Complet Page 12 of 57

13 Chair Parts List Project: Beer Complet Page 13 of 57

14 Chair 2D Documentation Project: Beer Complet Page 14 of 57

15 Project: Beer Complet Page 15 of 57

16 Project: Beer Complet Page 16 of 57

17 Project: Beer Complet Page 17 of 57

18 Project: Beer Complet Page 18 of 57

19 Project: Beer Complet Page 19 of 57

20 Project: Beer Complet Page 20 of 57

21 Project: Beer Complet Page 21 of 57

22 Project: Beer Complet Page 22 of 57

23 Project: Beer Complet Page 23 of 57

24 Project: Beer Complet Page 24 of 57 Bench Parts List

25 Project: Beer Complet Page 25 of 57 Bench 2D Documentation

26 Project: Beer Complet Page 26 of 57

27 Project: Beer Complet Page 27 of 57

28 Project: Beer Complet Page 28 of 57

29 Project: Beer Complet Page 29 of 57

30 Project: Beer Complet Page 30 of 57

31 Project: Beer Complet Page 31 of 57

32 Project: Beer Complet Page 32 of 57

33 Project: Beer Complet Page 33 of 57

34 Project: Beer Complet Page 34 of 57

35 Project: Beer Complet Page 35 of 57 Table Assemblage Instruction 1. Join the Leg with hart (item 2) and Leg with decoration (item 3) with glue. After this step, you should put that subassembly into the clamp, until the glue dries out.

36 Project: Beer Complet Page 36 of Place the Support (items 4) on their places from the both sides of a subassembly made in a previous step and fasten them with clamp. Drill the holes D8,5mm and fasten the Support (items 4) onto the assembly from a previous picture using standard parts: Bolt M8x150mm (item 7), Washer 8 (item 8), Lock Washer A8 (item 9) and Hexagon Nut M8 (item 10). Project from

37 Project: Beer Complet Page 37 of 57

38 Project: Beer Complet Page 38 of Fasten the Table Paw (item 13) onto the subassembly made in a previous step by using Wood screw (item 11). Before using Wood screws, drill the proper pilot holes (by following 2D documentation).

39 Project: Beer Complet Page 39 of 57

40 4. Form two of these subassemblies. Project: Beer Complet Page 40 of Join together the two subassemblies made in a previous step using Table horizontal (item 5) and Wedge (item 6).

41 Project: Beer Complet Page 41 of 57

42 Project: Beer Complet Page 42 of Fasten the Table Plank (item 1) onto the subassembly made in a previous step using Wood screws (item 11 and 12). Before using Wood screws, drill the proper pilot holes (by following 2D documentation).

43 Project: Beer Complet Page 43 of 57

44 Project: Beer Complet Page 44 of 57

45 Chair And Bench Assemblage Instruction Project: Beer Complet Page 45 of Carefully place the Big Leg (item 1) and Leg Small (item 2) in proper position, clutch them in clamp and then drill the holes D8,5mm by following 2D documentation. Join these two items together using Washer 8 (item 3), Lock Washer A8 (item 4), Hexagon Nut M8 (item 5) and Bolt M8 x 90mm (item 6).

46 Project: Beer Complet Page 46 of 57

47 Project: Beer Complet Page 47 of Fasten the Paw (items 12) to the subassembly made in previous step with Wood screws (item 11). Before using Wood screws, drill the proper pilot holes (by following 2D documentation).

48 Project: Beer Complet Page 48 of 57

49 Project: Beer Complet Page 49 of Form the two of these subassemblies.

50 Project: Beer Complet Page 50 of Fasten the Chair Seat Plank 2 (item 7) and Chair Seat Plank 1 (item 8) to the assembly made in previous step with Wood screws (item 11) by the given measurements. Before using Wood screws, drill the proper pilot holes (by following 2D documentation).

51 Project: Beer Complet Page 51 of 57

52 Project: Beer Complet Page 52 of Fasten the Chair Back Plank (item 9) to the assembly made in previous step with Wood screws (item 11) by the given measurements. Before using Wood screws, drill the proper pilot holes (by following 2D documentation). Project from

53 Project: Beer Complet Page 53 of Fasten the Chair Back Plank Small (item 10) to the assembly made in previous step with Wood screws (item 11). Before using Wood screws, drill the proper pilot holes (by following 2D documentation).

54 Project: Beer Complet Page 54 of Fasten the Chair Horizontal (item 13) to the assembly made in previous step with Wood screws (item 11). Before using Wood screws, drill the proper pilot holes (by following 2D documentation).

55 Project: Beer Complet Page 55 of 57

56 Project: Beer Complet Page 56 of 57

57 Project: Beer Complet Page 57 of 57 Follow exactly the same instructions to assemble the Bench.