assembly instructions
|
|
- Vivian Elliott
- 7 years ago
- Views:
Transcription
1 assembly instructions
2 1 // this guide is for Urban Chic gents & ladies.
3 // this guide is for Urban Chic gents & ladies. 2
4 1 x ph screwdriver 2 x 10mm spanners 1 x 15mm spanners 1 x 13mm spanners 1 x 6mm umbraco key These are all the tools you need 3
5 // What s in the box In the big box you will find the bicycle and smaller box with pedals, saddle and seatpost and the spring for the steering. 422
6 // Step 1. Assembling the Stem, handelbar, gear cabel and bell step 1-01 Insert the stem into the head tube step 1-02 Then tighten the stem top bolt with a 6mm umbraco key 5
7 step 1-03 Loosen the 6mm umbraco bolt and twist the handelbar to a approx 30 degrees position step 1-04 Loosen one of the screws with a screwdriver, then twist the bell to the position as shown above and tighten the screw step 1-05 Press the cable into the cable holders as shown above 6
8 // Step 2. Now its time for assembling the mudguard and the front wheel 7
9 step 2-01 Push the front mudguard up as shown above Insert the bolt through the reflex mudguard and fork hole step 2-02 Mount the washer and nut and tighten the bolt with your fingers step 2-03 Use 2x10mm spanners to tighten the nut and bolt as shown above 8
10 step 2-04 Remove the grooved washers and the normal flat washer and nuts on both sides of the axle step 2-05 Fit the wheel into the front fork step 2-06 Mount the grooved lock washer so that the grooved side touches the fork 9
11 step 2-07 Fit the mudguard stay on the axle, Then fit the flat washer on the axle step 2-08 Fit the bolt and then tighten the front wheel on both sides make sure that the wheel is centred between the fork arms when tightening the bolts 10
12 // Step 3. Now its time to fit the brake Brake arm step 3-01 Press the brake claws towards eachother and fit the cable into the brake arm and push the rubber seal on as shown above 11
13 step 3-02 Insert the cable stop into the brake lever step 3-03 Now turn the barrel until the grooves are lined up step 3-04 Fit the cabel as into the groove and turn the cable adjusters so the groove is closed 12
14 // Step 4. Now its time to mount the pedals step 4-01 Contents from the small box 13
15 Please note There is a difference between left and right hand side pedals. Left hand side pedal is marked L and right hand side pedal is marked R 14
16 step 4-02 Right hand side pedal must be fitted on chainguard side step 4-03 Insert the right pedal into the crank arm with your fingers. Turn the pedal end clockwise untel tight step 4-04 Tighten with 15mm 15
17 step 4-05 Insert the left pedal into the crank arm with your fingers. Turn the threaded pedal end counterwise untel tight 16
18 // Step 5. Now its time to mount the saddle step 5-01 Fit the seatpost in the saddle clamp and tighten with a 13mm spanner step 5-02 Now fit the seadpost into the seat tube as shown above and tighten with a 13mm spanner and 6mm allen key 17
19 18
20 // Gents. NB: If you have purchased a front cerrier, follow these instructions 19
21 //front carrier step 1. Assembly instructions for the front carrier 20
22 Ratchet with 13mm top T10 torx bit 2 x 10mm spanners 1 x rubber hammer Tools needed for assembling the front carrier and fit it on the bicycle 21
23 step 1-01 Front carrier frame step x 13mm nuts, 4 x washers, 2 x U-bolts, 1 x spanning block, and 1x protection cap step x wood panels, 1 x wood end panel 22
24 step 1-04 Places all wood panels on a table. Now place the front carrier frame up-side-down over the wood panels step 1-05 Fasten the 12 x 12mm screws with T10 bit 23
25 step 1-06 Attach the back wood panel step 5-07 Fit the back wood panel on the top part of the frame step 5-08 Fasten the 2 x 12mm screws with T10 bit 24
26 step 1-09 Remove the foil on the spacing block step 1-10 Now place the spacing block on the back of the front carrier between the 4 holes step 1-11 Thats it 25
27 //front carrier step 2. Now time for to fit the front carrier on the bike 26
28 27 Note: If the front carrier retrofitted remove reflex
29 step 2-01 Attach the front carrier on the frame and the first U-bolt should be fitted in the top two holes step 2-02 Now fit one washer, one nut on each side and tighten the nuts with your fingers step 2-03 Fit the end cap under the u-bolt as shown above 28
30 step 2-04 Tighten nuts with 13mm socket wrench. IMPORTANT: Do not over-tighten the bolts as it can bent the head tube and damage the bicycle. step 2-05 Fit the second u-bolt as shown above step 2-06 Use a rubber hammer if the u-bolt is a bit tight and repeat step
31 step 2-07 Tighten all 4 nuts with 13mm socket wrench. step 2-08 Job done IMPORTANT: Do not over-tighten the bolts as it can bent the head tube and damage the bicycle. Tighten the bolts carefully one by one until the front carrier is securely mounted on the bicycles and cannot be moved from side to side by pulling the basket by hand. If front carrier is still loose then tighten the bolts a bit more until the front carrier cannot be moved from side to side by hand. 30
32 // ladies. NB: If you have purchased an aluminum basket follow the instructions for these 31
33 //Alubasket step 1. Assembly instructions for the alu-basket 32
34 step 5-01 Ratchet with 13mm top step mm allen key Tools needed for assembling the alu-basket and fit it on the bicycle 33
35 6 x 2 x 1 x 4 x 4 x Alu-basket 6x10mm umbraco bolts, 2xu-bolts, 1xrear panel, 4x13mm nuts and 4x washers 3x wood panels 34
36 step 1-01 Fit the wood panels with 10mm screws by using 3mm allen key step
37 //Alubasket step 2. Now it s time to fit the alu basket onto the bike step 2-01 Hold the basket up to the head tube of the bicycle step 2-02 Fit the first u-bolt and washer 36
38 step 2-03 Fit the end cap under the u-bolt as shown above step 2-04 Tighten nuts with 13mm socket wrench. IMPORTANT: Do not over-tighten the bolts as it can bent the head tube and damage the bicycle. 37
39 step 2-05 Fit the second u-bolt as shown above step 2-06 Tighten nuts with 13mm socket wrench. IMPORTANT: Do not over-tighten the bolts as it can bent the head tube and damage the bicycle. Tighten the bolts carefully one by one until the basket is securely mounted on the bicycles and cannot be moved from side to side by pulling the basket by hand. If basket is still loose then tighten the bolts a bit more until the basket cannot be moved from side to side by hand. 38
40 Head tube step 2-07 Note: If the alu basket conflicts with the handelbar adjust the alu basket slightly up or down the head tube 39
41 40
42 41
43 Thank you for choosing a velorbis product Your satisfaction is very important to us. and there would be something missing or broken don`t hesitate to contact us Velorbis Nørre Farimagsgade 63 dk-1364 Cobenhagen phone:
Your New Frog Bike. Congratulations on purchasing a new bike and thank you for choosing Frog!
Your New Frog Bike Congratulations on purchasing a new bike and thank you for choosing Frog! We know that you must be raring to go but before you do there s a few little things still to do to get you up
More informationASSEMBLY MANUAL SE-4S35
Automatic drive ASSEBLY ANUAL SE-4S35 AI-4S35 SG-4R35 Battery box otor unit Inter-4 hub CONTENTS WARNING 1 INSTALLATION CONITIONS Battery box Speed sensor Cable lengths and diameters otor unit Recommended
More informationOwner s Manual Read and keep this manual. Patents World Wide
Owner s Manual Read and keep this manual. Patents World Wide S & S Industries, Inc., Sarasota, FL, USA www.trail-gator.com Copyright 2008 All Rights Reserved The following manual is provided to assist
More informationSTEERING HANDLEBAR/FRONT WHEEL/ FRONT SHOCK ABSORBER
14 14 STEERING HANDLEBAR/FRONT WHEEL/ SCHEMATIC DRAWING ------------------------------------------------- 14-1 SERVICE INFORMATION------------------------------------------------ 14-2 TROUBLESHOOTING-----------------------------------------------------
More informationRear wheel brakes, servicing. Стр. 1 из 45. Note:
Volkswagen Touareg - Rear wheel brakes, servicing Стр. 1 из 45 46-2 Rear wheel brakes, servicing Rear brakes, FN 44 brake caliper, servicing Note: After replacing brake pads, depress brake pedal firmly
More informationGTI VR6 Front Wheel Bearing DIY http://www.gtishrine.com
GTI VR6 Front Wheel Bearing DIY http://www.gtishrine.com This procedure covers replacing the front wheel bearings. Tools and Parts required: Wheel Bearing Puller w/ ABS adapter. Available for rent from
More informationInstallation instruction do88 Intercooler for Volvo S40 / V50 / C30
Installation instruction do88 Intercooler for Volvo S40 / V50 / C30 This instruction shows how to replace the OEM intercooler with our performance intercooler. 2. 3. 1. 4. 5. Part number: ICM-170 6. At
More informationINSTALLATION INSTRUCTIONS. 6108 Air Spring Kit 2011+ Ford F250 Single Wheel 4WD 2011+ Ford F350 Dually 4WD (2011 F350 Single Wheel 4WD use p/n 6113)
INSTALLATION INSTRUCTIONS 6108 Air Spring Kit 2011+ Ford F250 Single Wheel 4WD 2011+ Ford F350 Dually 4WD (2011 F350 Single Wheel 4WD use p/n 6113) Thank you for purchasing a quality Hellwig Product. PLEASE
More informationINSTRUCTIONS. FLHR/C/S (Road King) FRONT END LOWERING KIT 1WARNING -J03242 REV. 10-19-04. General. Removal (Left and Right Forks) Kit Number 54614-05
INSTRUCTIONS -J04 REV. 0-9-04 General FLHR/C/S (Road King) FRONT END LOWERING KIT This kit is designed for installation on 00 and later FLHR/C/S Model Motorcycles. Road King models use the conventional
More informationVolkswagen Jetta, Golf, GTI 1999, 2000 Brake System 47 Brakes - Hydraulic Components (Page GR-47)
47 Brakes - Hydraulic Components (Page GR-47) FS III front brake calipers, servicing Front brake caliper piston, removing and installing FN 3 front brake calipers, servicing Front caliper piston, removing
More informationBicycoo BMX Instruction Manual 0014X Series
Bicycoo BMX Instruction Manual 0014X Series Joovy 2919 Canton Street Dallas, TX 75226 (877) 456-5049 Fax: (214) 761-1774 Email: customerservice@joovy.com Web Site: www.joovy.com ! WARNINGS Please read
More informationVW GOLF Mk4 TDI FRONT MOUNTING INTERCOOLER INSTALLATION INSTRUCTIONS
VW GOLF Mk4 TDI FRONT MOUNTING INTERCOOLER INSTALLATION INSTRUCTIONS Tools required: 10mm/13mm socket and 3/8 drive ratchet with extension Torx T20/25/30 screwdrivers or bits Phillips head screwdriver,
More information1. Lay out 2 pieces of 7/8" tubing and mark for bending as shown. Remember that the bend is in the shaded area as shown below in Figure 1.
MINI BIKE PLANS Page 1 INTRODUCTION Before starting to build your Mini-Bike, be sure that you have all the parts shown on the material list. You will note that tubing has been used in the construction.
More informationFront brakes (FN- 3), servicing
j a t Front brakes (FN- 3), servicing 46-1 Front brakes, servicing Note: Install complete repair kit. After replacing brake pads and before moving vehicle, depress brake pedal several times firmly to properly
More informationService Manual Rol-Lift
R 2000 Service Manual Rol-Lift Series: T and E Developed by Generic Parts Service This manual is intended for basic service and maintenance of the Rol-Lift pallet jack. The pallet jacks you are servicing
More informationUSER MANUAL PLEASE READ BEFORE ATTEMPTING TO OPEN THE BIKE. Design registered and patented
USER MANUAL PLEASE READ BEFORE ATTEMPTING TO OPEN THE BIKE Design registered and patented 1 2 3 4 5 6 7 8 9 10 11 12 CONTENTS Unfolding the bike (photo guide) (inside cover) INTRODUCTION Introduction 1
More informationSERVICE MANUAL Trax US
SERVICE MANUAL Trax US How to contact Permobil Permobil Inc. USA 6961 Eastgate Blvd. Lebanon, TN 37090 USA Phone: 800-736-0925 Fax: 800-231-3256 Email: info@permobilusa.com Head Office of the Permobil
More informationSlide the new steering column shaft through the steering column from the driver compartment.
Slide the new steering column shaft through the steering column from the driver compartment. Push the column shaft through the steering column until the machined end is out past the column lower bushing.
More informationJoplin Rebuild Instructions
Joplin Rebuild Instructions This is a step by step list of instruction on how to rebuild the Crankbrothers Joplin post. It may not always be required to completely tear-down the post to do the work needed
More informationINSTALLATION INSTRUCTIONS. 6111 Air Spring Kit 2011+ Ford F250/F-350 Single Wheel 2WD 2011+ Ford F350 Dually 2WD IMPORTANT NOTES
INSTALLATION INSTRUCTIONS 6111 Air Spring Kit 2011+ Ford F250/F-350 Single Wheel 2WD 2011+ Ford F350 Dually 2WD Thank you for purchasing a quality Hellwig Product. PLEASE READ THIS INSTRUCTION SHEET COMPLETELY
More information1.8 CRANKSHAFT OIL SEALS
SERIES 60 SERVICE MANUAL 1.8 CRANKSHAFT OIL SEALS An oil seal is fitted between each end of the crankshaft and the bores of the flywheel housing and gear case cover to retain the lubricating oil in the
More informationDrive shaft, servicing
Volkswagen Passat B6 - Drive shaft, servicing Стр. 1 из 41 40-7 Drive shaft, servicing Drive shafts, overview I - Assembly overview: Drive axle with CV joint VL100 40-7, Drive axle with CV joint VL100,
More informationRetrofit Instructions Installing a Sport Heated Steering Wheel - Leather, Multifunction BMW X5, E53, 2001 2006
Retrofit Instructions Installing a Sport Heated Steering Wheel - Leather, Multifunction BMW X5, E53, 2001 2006 Disclaimer: This set of instructions is simply a guide on how I installed my own heated steering
More information6 inch A-Arm Lift Kit WARNING: 16-018/16-019. installation instructions. will fit CLUB CAR DS. included:
Revised May 205 6-08/6-09 6 inch A-Arm Lift Kit will fit CLUB CAR DS installation instructions included: Rear Lift Blocks Main Suspension Assembly Spindles A-Arms Rear Shock Mounting Plates U-Bolts WARNING:
More informationFRONT BUMPER INSTALLATION INSTRUCTIONS 2007-2011 DODGE / MERCEDES SPRINTER
Aluminess Products Inc 9402 Wheatlands Ct. #A Santee, CA 92071 619-449-9930 FRONT BUMPER INSTALLATION INSTRUCTIONS 2007-2011 DODGE / MERCEDES SPRINTER Please read before beginning Stainless steel hardware
More informationS OUNTING INSTRUCTION M M o u n t i n g k i t 2 &
M O U N T I N G I N S T R U C T I O N S instructions This document is protected by copyright. The SICK AG company retains this right. Reproducing this document in whole or part is only permissible within
More informationTrike Assembly Manual
Trike Assembly Manual Revised 3-98 Attach this coupon to your receipt and present both to dealer if service is required. Owner's name Address City State Zip Date purchased Model no. Serial no. Dealer's
More informationELECTRIC BICYCLE USER MANUAL
ELECTRIC BICYCLE USER MANUAL 1 Main Technical Parameters and Specification Weight: 23 kg Wheel size: 20 Maximum speed: 25 km/h E BIKE URBAN Range: Up to 45km (with pedal assist) Type: lithium Voltage:
More informationOwner s Manual for Cruiser Bicycles
Owner s Manual for Cruiser Bicycles This manual contains important safety, assembly, operation and maintenance information. Please read and fully understand this manual before operation. Save this manual
More informationVolkswagen Jetta, Golf, GTI 1999, 2000 Brake System 46 Brakes - Mechanical Components (Page GR-46)
46 Brakes - Mechanical Components (Page GR-46) Front brakes Brake pads, removing and installing Brake pads, removing and installing FN 3 brake caliper, servicing FS III brake caliper, servicing Rear wheel
More informationMicro Cart User's Guide
Micro Cart User's Guide To take full advantage of the ergonomic features of your new Sun Mountain Micro Cart, please read the following information. SUN MOUNTAIN 1 Your Micro Cart has several innovative
More informationRollator Cane and Brake Replacement SAFETY SUMMARY (CONTINUED)
Rollator Cane and Replacement Assembly, Installation and Operating Instructions SAVE THESE INSTRUCTIONS NOTE: Check ALL parts for shipping damage. If shipping damage is noted, DO NOT use. Contact Carrier/Dealer
More informationTABLE OF CONTENTS. Section 1 - Assembling your new pit bike.
Orion Pit Bike Sales Owners Manual (All information and content is the property of Orion Pit Bike Sales. Any attempt to copy or resell is a direct violation of our copyright. All violators will be prosecuted)
More informationebike City OPERATING MANUAL
ebike City OPERATING MANUAL IMPORTANT SAFEGUARDS: IMPORTANT: READ ALL INSTRUCTIONS BEFORE USE. RETAIN INSTRUCTIONS FOR FUTURE REFERENCE. WARNING: Basic safety precautions should always be observed when
More informationLittle British Car Co.
Little British Car Co. 29311 Aranel, Farmington Hills, MI 48334-2815, USA Tel: 248 489 0022 or 800 637 9640 Fax: 248 489 9665 On the web at: www.lbcarco.com E-mail: LBCarco@LBCarCo.com MGB Tube Rear Shock
More informationUser manual and assembly instructions. Models: Postman, Sunbather, Candy, Steeler, Electrifier, Patriot
User manual and assembly instructions Models: Postman, Sunbather, Candy, Steeler, Electrifier, Patriot 1 Table of contents Table of contents... Błąd! Nie zdefiniowano zakładki. 1. Package contents... Błąd!
More informationZAPPY 3 OWNER S MANUAL. Read this manual completely before riding your Electric ZAPPY 3.
ZAPPY 3 OWNER S MANUAL Read this manual completely before riding your Electric ZAPPY 3. TECHNICAL INFORMATION Model No. : ZAPPY 3 Product size Type of motor Motor power Battery type Battery Charger Charging
More information12. REAR WHEEL/BRAKE/SUSPENSION
12 12 12-0 SERVICE INFORMATION... 12-1 REAR BRAKE... 12-5 TROUBLESHOOTING... 12-2 REAR SHOCK ABSORBER... 12-8 REAR WHEEL... 12-3 REAR FORK... 12-9 SERVICE INFORMATION GENERAL INSTRUCTIONS When installing
More information2006 HEADSHOK Service Video #1
LEFTY SPEED DLR DAMPING CARTRIDGE This document explains how to properly remove, disassemble, inspect, reassemble and reinstall the Lefty Speed DLR2 damping cartridge. It is a document to be used in conjunction
More informationFREESTYLE BMX BIKE FREESTYLE BIKE. Assembly Manual. Important Please read these instructions fully before starting assembly 402/9764 391/5116
FREESTYLE BMX BIKE ssembly Manual FREESTYLE BIKE 402/9764 391/5116 Important Please read these instructions fully before starting assembly These instructions contain important information that will help
More informationCOOPER S PULLEY UPGRADE KIT INSTALLATION INSTRUCTIONS PART NUMBER NME5011
COOPER S PULLEY UPGRADE KIT INSTALLATION INSTRUCTIONS PART NUMBER NME5011 Below are instructions for the Mini Mania Pulley Upgrade Kit, Part Number NME5011. Please take all necessary precautions for working
More informationINSTRUCTIONS: LocknCharge Laptop Carts
INSTRUCTIONS: LocknCharge Laptop Carts www.lockncharge.com Extra Tools required: Hammer, Philips head screwdriver, medium adjustable spanner. (Allen key supplied) (Panel colours for illustration purposes
More informationELECTRIC BICYCLE OWNER S MANUAL SUPPLEMENT
ELECTRIC BICYCLE OWNER S MANUAL SUPPLEMENT For Owners of EG Le Mans, EG Milan Electric Bicycle Table of Contents Descriptions: Page Installation Instructions 2 How to install the bicycle out of the box
More informationStrut Spring Compressor
Strut Spring Compressor Item 43753 Read this material before using this product. Failure to do so can result in serious injury. SAVE THIS MANUAL. When unpacking, make sure that the product is intact and
More informationContents. 1 Introduction Safety Signal Words...2
26 Adult Tricycle SCHWINN Do not return to store. Call toll free (800) 626-2811 for assistance and replacement parts. The owner s manual contains safety, assembly, use, and maintenance instructions. The
More informationCorkSport Mazdaspeed 6 Rear Sway Bar 2006-2007 Mazdaspeed 6
CorkSport Mazdaspeed 6 Rear Sway Bar 2006-2007 Mazdaspeed 6 Pre-Installation Notes: The CorkSport Rear Sway Bar is a great addition to improving the handling performance to the Mazdaspeed 6. It will minimize
More informationDM-PD0001-00. (English) Dealer's Manual PD-MX80
(English) DM-PD0001-00 PD-MX80 Dealer's Manual IMPORTANT NOTICE This dealer s manual is intended primarily for use by professional bicycle mechanics. Users who are not professionally trained for bicycle
More informationGo-kart for little race-drivers
Go-kart for little race-drivers Drill and drive. Go-kart What it lacks in speed, it more than makes up for in fun: the go-kart will excite little race-drivers. 1 Introduction It s only a go-kart, but it
More informationCable Drum Installation
20 Cable Drum Installation COUNTERBALANCE None Shake the TorqueMaster spring tube gently to extend the winding shafts out about 5" on each side. For single spring applications, there will be no left hand
More informationSLACK PERFORMANCE KARTS
SLACK PERFORMANCE KARTS SET UP GUIDE Thank you for purchasing a 2013 Slack Axiom Chassis. Performance Mfg. strives to provide you with the very best chassis and components on the market today. Your satisfaction
More informationWWW.SHAUNWHITESUPPLYCO.COM
Bike Owner s Manual CONGRATULATIONS ON THE PURCHASE OF YOUR NEW BIKE! OUR SERVICE DEPARTMENT IS DEDICATED TO MAKING SURE THAT YOU GET THE MOST ENJOYMENT POSSIBLE FROM OUR PRODUCTS. For questions regarding
More informationWorksman PortoTrike: The Compact Deluxe Adult Folding Tricycle Assembly Instructions, Parts List, and Owners Manual
- 1 - Worksman PortoTrike: The Compact Deluxe Adult Folding Tricycle Assembly Instructions, Parts List, and Owners Manual Congratulations on your purchase of the Worksman PortoTrike Compact Folding Tricycle,
More informationSL-RS41-7T SL-RS31-7T
SERVICE INSTRUCTIONS SI-R912A t SL-RS41-7T SL-RS31-7T REVO SHIFT (Shifting lever) Before use, read these instructions carefully, and follow them for correct use. WARNING Use neutral detergent to clean
More information2740 Whitten Rd Bldg 103 Memphis, TN 38133 Telephone 901-380-9290 Email Bwilliams@Dieselcare.net
Fuel Injection Pump Replacement REMOVAL Diesel Care & Performance Inc 1. Disconnect negative battery terminal. 2. Remove throttle linkage. Fuel Injection Pump Bracket 3. Remove injection pump bracket.
More informationRange Road RR Series Semi-Automatic Firewood Processor. Crated Unit Assembly Manual
Range Road RR Series Semi-Automatic Firewood Processor Crated Unit Assembly Manual 1 1) Undo 8-18mm x 19mm Nuts and bolts, 2 on each leg of top frame 2) Lift top of Metal crate off and move out of work
More informationPost Mount Light Installation*
Post Mount Light Installation* *For the general installation of most Post Mount Spotlights, many vehicles may need slight modifications to these instructions. You will need the following tools: High torque
More informationLG G5 Chassis Brace Gen 5 Camaro THE MOST POWERFUL HEADERS ON THE PLANET Brought to you by LG Motorsports 972-429-1963
LG G5 Chassis Brace Gen 5 Camaro THE MOST POWERFUL HEADERS ON THE PLANET Brought to you by LG Motorsports 972-429-1963 Thank you for purchasing LG Motorsports products for your Gen 5 Camaro. Parts Inventory:
More information13. REAR WHEEL/BRAKE/SUSPENSION
13. REAR WHEEL/BRAKE/SUSPENSION 13 3.5~4.5kg-m 8.0~10.0kg-m 0.8~1.2kg-m 3.0~4.0kg-m 2.4~3.0kg-m 3.5~4.5kg-m 6.0~8.0kg-m 13-0 13. REAR WHEEL/BRAKE/SUSPENSION 13 REAR WHEEL/BRAKE/SUSPENSION SERVICE INFORMATION...
More informationH EAD TUBE BASICS. Figure 1 - Head tube, front fork and hardware
H EAD TUBE BASICS Figure 1 - Head tube, front fork and hardware This tutorial will cover some of the basics you need to know when pulling apart the steering system of a bicycle for repair or use on one
More informationDR125 and DR150 Hensim Dirt Runner 125cc and 150cc Dirt Bike (VIN PREFIX LLCH or LUAH)
Parts Lists - DR125 and DR150 Hensim Dirt Runner 125cc and 150cc Dirt Bike (VIN PR... Page 1 of 25 Product Information Baja Web > Product Information > Parts Lists > DIRTBIKE > DR125 and DR150 Hensim Dirt
More informationDYNA RIDER FOOTBOARD KIT
-J0 REV. 0-0-0 DYNA RIDER FOOTBOARD KIT GENERAL Kit Number 000 Models For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com (English
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application 2009 PILOT Publications No. AII 39408 Issue Date MAY 2008 PARTS LIST Steering Wheel Trim (With Cruise and Audio) P/N 08Z13-SZA-130B (Chocolate) P/N 08Z13-SZA-140B
More information3. Loosen 3 x grub screws in the Dec end cap and unscrew the cap and counterweight shaft. NEQ6 Belt Modification Kit.
NEQ6 Belt Modification Kit. Thank you for your purchase. Please read these instructions fully before fitting. Your package should contain 2 off 47 & 2 off 12 tooth aluminium pulleys 2 off belts 6mm wide
More informationELECTRIC BICYCLE OWNER S MANUAL
ELECTRIC BICYCLE OWNER S MANUAL For Owners of EG Bali 500EX and EG Milan 500EX Electric Bicycle Table of Contents Descriptions: Page Installation Instructions 2 How to install the bicycle out of the box
More informationDO NOT attempt to repair hub and wheel bearing assembly.
Page 1 of 6 HUB & WHEEL BEARINGS (WITH PULSE VACUUM HUBLOCK) DO NOT attempt to repair hub and wheel bearing assembly. Removal DO NOT remove hub lock assembly by prying on hub lock legs. This can crack
More informationService Manual Supplement
Volvo Trucks North America, Inc. Greensboro, NC USA This Service Bulletin is a supplement to Service Manual, Group, Anti-lock Brake System (ABS), Bendix, VNL, VNM publication number PV /. Service Manual
More informationWhite Industries Rear Hub Instructions
White Industries Rear Hub Instructions Tool required: 2mm allen/hex wrench, 19mm socket, 20mm socket, and mallet. 1. Loosen the set screws located in the adjusting collar by using a 2mm allen wrench inserted
More informationOperating Instructions Parts List Manual Scissor Lift Pallet Truck
Operating Instructions Parts List Manual Scissor Lift Pallet Truck Note: Operator MUST read and understand this operating instructions before use this Hand Scissor Lift. Thank you for using this hand scissors
More informationCETAC Z-Drive Assembly
CETAC Z-Drive Assembly Replacement Guide Manual Part Number 610144 Rev 1, 2012 CETAC Technologies, Printed in USA Overview This guide describes the necessary steps to replace the Z-drive assembly on your
More informationFRONT TURN SIGNAL RELOCATION KIT
-J0 REV. 00-0-0 FRONT TURN SIGNAL RELOCATION KIT GENERAL Kit Number -0 Models This kit fits 00 and later Dyna model motorcycles (except FXDSE), relocating the front turn signal from the handlebars to the
More information1/29/2008 DR125 / DR150. Baja Motorsports Inc. P.O. Box 61150 Phoenix, AZ 85082 Toll Free: 888-863-2252 PARTS AND PRICES ARE SUBJECT TO CHANGE 1 of 55
DR125 / DR150 Toll Free: 888-863-2252 PARTS AND PRICES ARE SUBJECT TO CHANGE 1 of 55 CYLINDER HEAD ASSY. 1 125-001 883099006937 CYLINDER HEAD COVER 1 1 2 125-002 883099006944 BOLT M6X28 2 3 3 125-003 883099006951
More informationTech Bulletin. Hose / Cord Replacement and Required Wraps. Series RT
Tech Bulletin Hose / Cord Replacement and Required Wraps Series RT Replacing the Hose To remove the hose - Pull out the hose leaving 2 to 3 feet on the spool. Engage the latch pawl. Remove the U-bolt nuts
More informationBODY-12, Door Handle - Removal, Installation, and Adjustment
Introduction BODY-12, Door Handle - Removal, Installation, and Adjustment There are many different procedures floating around describing how to replace the door handles on a 944 and every one of them will
More informationELECTRIC BICYCLE OWNER S MANUAL
ELECTRIC BICYCLE OWNER S MANUAL For Owners of EG Athens 250 Electric Bicycle Table of Contents Descriptions: Page Installation Instructions 2 How to install the bicycle out of the box 2 Operation Instructions
More informationTools. Spanners Screwdrivers Spoke key
Tools If all of this sounds like too much trouble and expense to purchase all at once, then don t worry. Just gather together the basic items and add to your toolkit as and when you need. Finally, if your
More informationPulleys and Belt. Install the Major Accessory and Pulley. Install the Motor Pulley NOTE. Align the Motor Pulley and the Tool Pulley NOTE
Pulleys and Belt Pulley Guard - 505862 Install the Major Accessory and Pulley 1. Place the short end of the mounting base holes, and insert - but don t tighten - the setscrews. If the Major Accessory has
More information46431x92A Garden Tractor (1998) Page 1 of 16 Body Chassis
46431x92A Garden Tractor (1998) Page 1 of 16 Body Chassis 46431x92A Garden Tractor (1998) Page 2 of 16 Body Chassis 1 092546E701 Bracket, Seat 2 091963 Z Plate Assembly, Switch 3 164X26 Spring, Compression
More informationSolstice/Sky Water Pump Replacement
Solstice/Sky Water Pump Replacement The water pump on the Solstice/Sky is starting to need replacement on some vehicles. This guide will help in replacing the water pump while the engine is still in the
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory TRIM Application 2008 ACCORD 4-DOOR Publications No. AII 35362 Issue Date AUG 2007 PARTS LIST Steering Wheel Trim (Without Navigation) P/N 08Z13-TA0-100 Right steering
More informationSERVICE PARTS LIST PAGE 1 OF 6 BASE ASSEMBLY SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS 12" DUAL BEVEL COMPOUND MITER SAW B27A
PAGE 1 OF 6 BASE ASSEMBLY 00 0 EXAMPLE: Component Parts (Small #) Are Included When Ordering The Assembly (Large #). SPECIFY CATALOG NO. AND NO. WHEN ORDERING PARTS 1 02-80-0050 Thrust Bearing (1) 2 05-80-0510
More informationPOLEMOUNT FIELD FIX ASSEMBLY INSTRUCTIONS
POLEMOUNT FIELD FIX ASSEMBLY INSTRUCTIONS Polemount Field Fix Support If you have any questions or incur any problems installing or using the new Polemount, please use Miovision s Support System by emailing
More informationOverview PARTS LIST. B. Lever mounting base C. Flush handle assembly D. Grey/Blue float stop E. Grey float (Full Flush) F. Flush valve washer
Overview READ ENTIRE INSTRUCTIONS BEFORE STARTING INSTALLATION PARTS LIST A. Flush valve B. Lever mounting base C. Flush handle assembly D. Grey/Blue float stop E. Grey float (Full Flush) F. Flush valve
More informationThanks for choosing Toroidal. This file is developed to assist you in assembling and aligning Toroidal Dish.
Assembling Toroidal Thanks for choosing Toroidal. This file is developed to assist you in assembling and aligning Toroidal Dish. With Toroidal dish, you are aiming for more than 1 satellite and therefore
More informationSERVICE MANUAL. Corpus 3G. Seat system for electric wheelchair
SERVICE MANUAL US Corpus 3G Seat system for electric wheelchair How to contact Permobil Head Office of the Permobil group Produced and published by Permobil AB, Sweden Version 4, 2014-07 Item No.: 205260-US-0
More informationContents. Front Derailleurs... 2. Part One - Planning... 2 I. Objectives... 2 II. Materials Needed... 2 III. Setting...2 IV. Evaluation...
Contents... 2 Part One - Planning... 2 I. Objectives... 2 II. Materials Needed... 2 III. Setting...2 IV. Evaluation... 2 Part Two - Activity Instructions... 3 Steps to Adjusting and Replacing... 3 Disassemble...
More information2011-14 F250 6 RADIUS ARM KIT
92154000 Thank you for choosing Rough Country for your suspension needs. 2011-14 F250 6 RADIUS ARM KIT Rough Country recommends a certified technician installs this system. In addition to these instructions,
More informationStructural Holding System
Structural Holding System Users Manual November 2013 by Vehicle Service Group. All rights reserved. CO8812.1 502071 Rev. - 11/21/2013 CHIEF'S LIMITED ONE-YEAR WARRANTY & LIABILITY Chief Automotive Technologies
More information2003 Audi A4. AUDI' '3.0L V6 - AVK Engine - A4 & A6
Installation (A4) CAUTION: Before installation, ensure camshafts are aligned, crankshaft is locked in place and camshaft gear bolts are loose as described in removal procedures. When turning camshaft,
More informationMODEL 565E - 22 TON AIR/HYDRAULIC AXLE JACK
1 565AKHU HYDRAULIC 1.22 O-RING - 2 REQUIRED UNIT 1.23 O-RING COMPLETE 1.24 TEFLON O-RING 2 REQUIRED 1.3 EXTENSION SCREW 1.3A SPRING PIN 1.4 SPRING SUPPORT 1.5 SCREW BUSHING 1.6 Y SHAPE SEAL RING 1.7 HEAD
More informationFront axle components, overview
just a test. Front axle components, overview 40-1 General Information Load bearing components and parts of the suspension must not be welded or straightened. Vehicles without drive axle must not be moved,
More informationAstroSystems Digital Setting Circles for Zhumell, GSO, Apertura and Astro-Tech
AstroSystems Digital Setting Circles for Zhumell, GSO, Apertura and Astro-Tech Components 1 Sky Commander Digital Setting Circle Computer 2 Encoders 10,000 step 1 Sky Commander Digital Setting Circle Manual
More informationDR50 Hensim Dirt Runner 49cc Dirt Bike (VIN PREFIX LLCH or LUAH)
Page 1 of 21 Product Information Baja Web > Product Information > Parts Lists > DIRTBIKE > DR50 Hensim Dirt Runner 49cc Dirt Bike (VIN PREFIX LLCH or LUAH) DR50 Hensim Dirt Runner 49cc Dirt Bike (VIN PREFIX
More informationTrouble Shooting Tech Tips Operation
Steering Components TroubleShooting Tech Tips Table of Contents Basic Steering System Operation 2 Sector Shaft Adjustments 4 Drag Link Adjustment 5 Relief Valve/Unloading Valve Adjustment 6 Ross TAS Automatic
More informationHOME GYM. Model. Retain This Manual for Reference OWNER'S MANUAL. www.hyper-extension.com
NOTE: Please read all instructions carefully before using this product Table of Contents Safety Notice www.hyper-extension.com HOME GYM 50036 Hardware Identifier Assembly Instruction Parts List Warranty
More informationFor exploded diagram and part number information, refer to the Spare Parts Catalog available on our website at www.rockshox.com.
For exploded diagram and part number information, refer to the Spare Parts Catalog available on our website at www.rockshox.com. 2 0 0 5 D U K E A I R X C / S L / R A C E S E R V I C E G U I D E Information
More informationFigure 2 The fan and shroud also needs to be removed for access to the four a/c compressor bolts and removal of the compressor from the top.
Here are some pictures to show what s required when replacing the A/C compressor, expansion valve and receiver/drier on a 2001 Volvo V70. Even if you don t replace these A/C parts these pictures can help
More informationFor exploded diagram and part number information, refer to the Spare Parts Catalog available on our website at www.rockshox.com.
For exploded diagram and part number information, refer to the Spare Parts Catalog available on our website at www.rockshox.com. Information contained in this publication is subject to change at anytime
More informationFitting Instructions Garador, Westland & Catnic Garage Door Spring Box Roller Wheels & Wall Bracket & Link Arm
Fitting Instructions for a Garador, Westland & Catnic Garage Door Spring Box Roller Wheels & Wall Bracket & Link Arm These instructions cover, how to replace a Spring Box Assembly to a Garador, Westland
More informationINSTALLATION INSTRUCTIONS FOR 2006-2009 VW MK5
CI100018 INSTALLATION INSTRUCTIONS FOR 2006-2009 VW MK5 Rabbit, Jetta 2.5L These instructions are applicable to vehicles equipped with either manual or automatic transmissions Thank you for choosing to
More informationSCION tc 2005-2008 COIL OVER SUSPENSION Preparation
SCION tc 2005-2008 COIL OVER SUSPENSION Preparation Part Number: PTR11-21070 NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents: Item # Quantity Reqd. Description
More information