SC532 9-PIN PERIPHERAL TO RS232 INTERFACE INSTRUCTION MANUAL

Size: px

Start display at page:

Download "SC532 9-PIN PERIPHERAL TO RS232 INTERFACE INSTRUCTION MANUAL"

Horace Curtis
7 years ago
Views:

2 WARRANTY AND ASSISTANCE The SC532 9-Pin Peripheral to RS232 Interface is warranted by CAMPBELL SCIENTIFIC, INC. to be free from defects in materials and workmanship under normal use and service for twelve (12) months from date of shipment unless specified otherwise. Batteries have no warranty. CAMPBELL SCIENTIFIC, INC.'s obligation under this warranty is limited to repairing or replacing (at CAMPBELL SCIENTIFIC, INC.'s option) defective products. The customer shall assume all costs of removing, reinstalling, and shipping defective products to CAMPBELL SCIENTIFIC, INC. CAMPBELL SCIENTIFIC, INC. will return such products by surface carrier prepaid. This warranty shall not apply to any CAMPBELL SCIENTIFIC, INC. products which have been subjected to modification, misuse, neglect, accidents of nature, or shipping damage. This warranty is in lieu of all other warranties, expressed or implied, including warranties of merchantability or fitness for a particular purpose. CAMPBELL SCIENTIFIC, INC. is not liable for special, indirect, incidental, or consequential damages. Products may not be returned without prior authorization. To obtain a Returned Materials Authorization (RMA), contact CAMPBELL SCIENTIFIC, INC., phone (435) After an applications engineer determines the nature of the problem, an RMA number will be issued. Please write this number clearly on the outside of the shipping container. CAMPBELL SCIENTIFIC's shipping address is: CAMPBELL SCIENTIFIC, INC. RMA# 815 West 1800 North Logan, Utah CAMPBELL SCIENTIFIC, INC. does not accept collect calls. Non-warranty products returned for repair should be accompanied by a purchase order to cover the repair. 815 W N. Logan, UT USA Phone (435) FAX (435) Campbell Scientific Canada Corp th Street Edmonton, Alberta T5M 1W7 CANADA Phone (403) FAX (403) Campbell Scientific Ltd. Campbell Park 80 Hathern Road Shepshed, Leics. LE12 9RP ENGLAND Phone (44) FAX (44)

3 SC532 TABLE OF CONTENTS PAGE 1. FUNCTION PHYSICAL DESCRIPTION SPECIFICATIONS HARDWARE CONNECTIONS OPERATION PORTABLE BATTERY POWER APPLICATION... 2 APPENDICES A. PIN DESCRIPTION...A-1 B. SCHEMATIC...B-1 C. COMPONENT LOCATION...C-1 FIGURES 1 SC532 Case Top Connection Block Diagram... 2 TABLES 1 CSI SC532 to External Battery Connections CSI Peripherals and Their Maximum Current Requirements... 3 A-1 SC532 Pin Description...A-1 A-2 DTE Pin Configuration...A-2

4 SC532 9-PIN PERIPHERAL TO RS232 INTERFACE 1. FUNCTION The SC532 Peripheral Interface connects an IBM PC/XT/AT or IBM PS2 compatible computer to certain Campbell Scientific datalogger peripherals. Peripherals include SM192/716 Storage Module, SM64 Storage Module, and MD9 Multidrop Interface. The SC532 replaces the SM232A Storage Module - RS232 Interface whenever the PC208 Datalogger Support Software is used to read Storage Modules. It also provides a +5 VDC power supply to the peripheral. A supply voltage of 6 to 17 VDC is required. 2. PHYSICAL DESCRIPTION The SC532 has a 9-pin connector for the peripheral and a 25-pin connector for the computer. An AC adaptor provides the input power (Figure 1). FIGURE 1. SC532 Case Top 3. SPECIFICATIONS Supply voltage in Output voltage +6 VDC to 17VDC; Factory installed AC to 7.5 VDC adaptor 5 VDC ± 0.2 VDC Current available 100 ma maximum at 25 deg. C; to peripheral derate 4 ma/v for each volt above 9VDC on 5V output on the supply voltage at 25 deg. C RS232 output levels RS232 input levels +10VDC ± 1 VDC -10VDC ± 1 VDC Maximum output impedance = 1100 ohms ± 30V maximum Low threshold 0.8V High threshold 3.5V Input impedance at least 3000 ohms 1

5 SC532 9-PIN PERIPHERAL TO RS232 INTERFACE 9-pin inputs Low 1V; High 3.5V 9-pin outputs Low 0.5V; High 3.5V Current drain Port Configuration Dimensions Weight 5 ma typical quiescent 10 ma maximum quiescent 25-pin D-Subminiature Female configured as DCE. 9-pin D-Subminiature Female connects to peripheral through the SC12 Two Peripheral Connector Cable supplied with the SC x 3 x 1 inches 1 pound with transformer FIGURE 2. Connection Block Diagram 4. HARDWARE CONNECTIONS The block diagram in Figure 2 shows the connection from a Campbell Scientific Inc. peripheral to a 25-pin RS232 Asynchronous Communication Adapter via the SC532 and a SC12 9-pin cable. If you have an AT computer with a 9-pin serial port, you will need a 9-pin to 25-pin cable in order to hook to the SC532 Interface. 5. OPERATION A Campbell Scientific Inc. peripheral's CMOS logic levels (0V logic low, 5V logic high) are converted to RS232 levels (-10V and +10V respectively) by the SC532 Interface. The SC532 also supplies +5VDC power to the peripheral. The factory-installed AC adapter must be plugged into a 110 VAC wall receptacle. You will need to write your own software if you are not using the PC208 Dataloggers Support Software. Read the specific peripheral manual for the necessary control sequence. Appendix A discusses the SC532 and the DTE computer pin descriptions. 6. PORTABLE BATTERY POWER APPLICATION If the SC532 is being used in a portable application with battery power such as collecting data on-site from a Storage Module, the AC adapter wire can be cut and split. The wires can be spliced to connectors. The user can then use the SC532 with a battery or with the AC adapter. See Table 1 to hook the SC532 to a battery. The battery voltage can be +6 to 17 VDC. See Table 2 for the current required for selected Campbell Scientific Inc. peripherals. 2

6 SC532 9-PIN PERIPHERAL TO RS232 INTERFACE TABLE 1. Campbell Scientific Inc. SC532 to External Battery Connections Transformer Connections Brand Wire Battery Terminal Archer Black w/ White +Positive Strip Solid Black -Negative Tamura Black w/ White -Negative Strip Solid Black +Positive TABLE 2. CSI Peripherals and Their Maximum Current Requirements Peripheral Maximum Current MD9 Multidrop Interface <90 ma SM192/716 Storage Module <20 ma SM64 Storage Module <30 ma 3

7 APPENDIX A. PIN DESCRIPTION The SC pin female port is configured as Data Communications Equipment (DCE) for direct cable connection to Data Terminal Equipment (DTE) such as an IBM-PC serial port. The pin descriptions of the SC pin female connector and 9-pin female connector are listed in the following table. PIN = Pin number I = Signal Into the SC532 0 = Signal Out of the SC532 TABLE A-1. SC532 Pin Description 25-PIN FEMALE CONNECTOR 9-PIN FEMALE CONNECTOR PIN# I/O DESCRIPTION PIN# I/O DESCRIPTION 1,7 GROUND 1 O +5V SUPPLY 2 I TX 2 GROUND 3 O RX 3 I RING 4 I RTS 4 I RX 20 I DTR 5 O ME 22 O RING 6 O PE 7 O CLK/HS 9 O TX A-1

8 APPENDIX A. PIN DESCRIPTION A computer configured as DTE, such as an IBM-PC, will adhere to the description in Table A-2. TABLE A-2. DTE Pin Configuration PIN = 25-pin pin number ABR = Abbreviation for the function name I = Signal Into the computer O = Signal Out of the computer PIN ABR I/O Function 1 Frame Ground. 2 TX O Transmit Data: Characters are transmitted from the computer on this line. 3 RX I Receive Data: Characters transmitted by a peripheral are received on this line. 4 RTS O Request To Send: The computer uses this line to control the peripheral's PE lines. 20 DTR O Data Terminal Ready: The computer uses this line to control the peripheral's ME and CLK/HS line. 22 RING I Ring Indicator: Raised to get the attention of the computer. 7 SG Signal Ground: Voltages are measured relative to this point. A-2

9 APPENDIX B. SCHEMATIC B-1

10 APPENDIX C. COMPONENT LOCATION C-1

INSTRUCTION MANUAL. MCR1 Memory Card Reader 5/93. Copyright (c) 1993 Campbell Scientific, Inc.

INSTRUCTION MANUAL. MCR1 Memory Card Reader 5/93. Copyright (c) 1993 Campbell Scientific, Inc. INSTRUCTION MANUAL MCR1 Memory Card Reader 5/93 Copyright (c) 1993 Campbell Scientific, Inc. Warranty and Assistance The MCR1 MEMORY CARD READER is warranted by CAMPBELL SCIENTIFIC, INC. to be free from