Contact Details. Please note that some of the contact details on this PDF document may not be current.

Transcription

1 Contact Details Please note that some of the contact details on this PDF document may not be current. Please use the following details if you need to contact us: Telephone: The Help Centre section of this website also features a wide range of information which may be of use to you and is available 24 hours a day. It includes: Operating and installation instructions downloads Request a repair Where to buy our products Literature downloads Heating requirement calculator centre A division of GDC Group Ltd Millbrook House Grange Drive Hedge End Southampton SO30 2DF Registered No: England VAT GB EEE Producer Registration Number WEE/GE0057TS Paper from sustainable sources

2 INSTALLATION GUIDE HOW TO POSITION AND PROGRAM THE FLASH PROGRAMMER 2S PRODUCT FUNCTIONS Centralised programming for two heating zones using two temperature modes: - Comfort temperature - Reduced temperature Manual override function in comfort and reduced mode for each room. PRINCIPLE OF OPERATION Convectors equipped with a suitable electromechanical thermostat: Reduced temperature obtained by supplying a resistance, which overrides the sensing element of the thermostat. Convectors equipped with a suitable electronic thermostat: Reduced temperature achieved by delivering an alternating signal (coding adopted by all designers since January 1994) TECHNICAL CHARACTERISTICS Time switch: Electronic clock with day and week programs. Power backup: By lithium battery, backup guarantee for a total of 3 years minimum against mains failure (battery life: 10 years) Program increments: 1 minute Number of zones: 2 Total maximum current rating: 0.5A Dimensions: 167mm x 84mm x 44mm INSTALLATION 1 Unscrew the time switch fixing screw 4 Electrical connections (see page 2) 2 Separate the base plate from the casing using a screwdriver 3 Surface-Mounted base with 2off screw fixings Ø3mm maximum IMPORTANT Insert the flying lead from the display panel into the socket on the circuit board as shown 5 Put outer casing back on 6 Put back in and tighten the time switch fixing screw 1

3 CONNECTING THE PILOT WIRE Whether mechanical or electronic, regardless of make, since January 1997, the reduced mode of a thermostat which can be programmed via pilot wire, is achieved by transmission of an alternation signal via the pilot wire ELECTRICAL CONNECTIONS FOR PILOT WIRE CONVECTOR HEATERS 1. All types of convectors since 1994: The pilot wire carries the live current to the convector Inputs: connect neutral to L1 and Live to L2 2. Convectors before January 1994: Check the convector instructions or if you have none, consult the manufacturer. In certain cases, the pilot wire carries the neutral current to the convector inputs. In this event, connect neutral to L2 and Live to L1. 2

4 WHY A PROGRAMMER USER GUIDE HOW TO PROGRAM AND USE THE FLASH PROGRAMMER 2S FOR GREATER CONTROL OF YOUR COMFORT: - The temperature you need at a time that suits you. FOR GREATER CONTROL OVER YOUR ENERGY COSTS: - Slightly lowering the temperature during the night or when you are not at home can achieve substantial savings. PRINCIPLE OF OPERATION FLASH PROGRAMMER 2S ALLOWS YOU TO PROGRAM TWO HEATING ZONES Example: - Day zone for the dining room, living room etc - Night zone for the bedroom etc THE TIMES YOU PROGRAM FOR EACH ZONE DEFINE THE COMFORT HEATING TIMES AND THE REDUCED HEATING TIMES Comfort Temperature : The temperature you want in the house when you are at home, which can be set Individually for each room. Reduced Temperature : The temperature you want in the house when you are away or at night MANUAL OPERATION FOR EACH INDIVIDUAL ZONE 1 AND 2 PROGRAMMING The dual zone time switch allows you to program 20 comfort or reduced switching times spread anywhere over the two zones. e.g. 12 switching times for zone 1 and 8 for zone 2. Each switching time can be applied to one or several days of the week. e.g. comfort mode from Monday to Friday at 7.00 represents one switching time. You now have 19 left. 3

5 BEFORE PROGRAMMING YOUR FLASH PROGRAMMER 2S TAKE TIME TO WRITE YOUR PROGRAM IN THE TABLES BELOW ZONE 1 (The first lines are filled with an example) ZONE 1 C1 Times Mon 1 Tue 2 Wed 3 Thu 4 Fri 5 Sat 6 Sun 7 Comfort 07:00 Example Reduced 08:00 Example ZONE 2 (The first lines are filled with an example) ZONE 2 C2 Times Mon 1 Tue 2 Wed 3 Thu 4 Fri 5 Sat 6 Sun 7 Comfort 20:00 Example Reduced 23:00 Example 4

6 1. SETTING THE TIME 2. PROGRAMMING 5

7 3. AUTO MODE 4. CHECKING SWITCHING TIMES 6

8 5. MODIFYING OR CANCELLING SWITCHING TIMES 7

9 6. PERMANENTLY OVERRIDING TIMER MODE 7. TEMPORARILY OVERRIDING TIMER MODE (HOLIDAYS etc) 8 APPLIED ENERGY PRODUCTS LIMITED MORLEY WAY, PETERBOROUGH PE2 9JJ TEL +44 (0) / FAX: +44 (0) Website: (Leaflet No AA Revision. A)