WinCue Pro/QSeries Version 1.3/1.5 Multi-user Interface Device Installation Guide

Size: px

Start display at page:

Download "WinCue Pro/QSeries Version 1.3/1.5 Multi-user Interface Device Installation Guide"

Naomi Freeman
7 years ago
Views:

2 Serial Items needed to use KDriver Serial Multi-user Interface device: 1 KDriver Serial to IMT Converter Box (Stack DAQ (Serial)) 1 Power Supply VDC 2 Straight Through Serial Cables. (Male 9 Way D to Female 9 Way D) Note: This box cannot be used in conjunction with Hybrid Multibutton, IMT Foot or IMT 2 button controllers. Connecting the serial box to the PC figure 1 To connect a Stack DAQ (Serial) box to a Prompter PC Connect the first straight through cable from the Female 9 way D on the K8055 box to a COM Port (Male 9 way D) on the Prompter PC, taking note of which COM port you have chosen. Connect the second straight through cable from the Male 9 way D on the Stack DAQ box to the external port on the IMT card (Female 9 way D), The IMT card may be inside the Prompter PC or in a Rack mounted box. Plug the supplied power adaptor into the Stack DAQ box. You should see the green LED on the left hand side of the box light up and the red LED on the right hand side flash once.

3 USB Items needed to use KDriver Multi-user Interface device: 1 KDriver USB to IMT Converter Box (K8055 (USB)) 1 Power Supply VDC 1 Straight Through Serial Cable. (Male 9 Way D to Female 9 Way D) 1 USB Cable Note: This box cannot be used in conjunction with Hybrid Multibutton, IMT Foot or IMT 2 button controllers. To connect a K8055 (USB) box to a Prompter PC Connect the USB cable from the USB port on the K8055 box to the USB port on the Prompter PC. Connect the straight through serial cable from the Male 9 way D on the K8055 box to the external port on the IMT card (Female 9 way D), The IMT card may be inside the Prompter PC or in a Rack mounted box. Plug the supplied power adaptor into the K8055 box. You should see the green LED on the left hand side of the box light up and the red LED on the right hand side flash once.

To configure the box in WinCue Pro Run WinCue Pro Go to the Tools Menu and Select Options, the WinCue Configuration dialog will appear (figure 1) figure 2 In the Right hand list in the WinCue

4 To configure the box in WinCue Pro Run WinCue Pro Go to the Tools Menu and Select Options, the WinCue Configuration dialog will appear (figure 1) figure 2 In the Right hand list in the WinCue Configuration dialog select Prompt Engine and then Hardware Settings, Tabbed Pages will appear in the left hand pane of the dialog, use the button with arrows if necessary to go to the furthermost tab (KDriver Interface) as in figure 2 If you are using a box with a Serial connection to the PC You ll need to select Stack DAQ Serial Box and change the COM port that the box is connected to. If the box is connected to the Prompter PC via a USB Cable then select K8055 USB Box. The Offset and Multiplier boxes are used to alter the scroll tables for the box, The defaults for these fields are Offset: 64 and Multiplier: 8 Multiplier Each scroll rate (from 0-255) will be multiplied by this figure to gain allow for faster scroll rates. Offset Each Scroll rate will have this offset added to it meaning the scroll table will be an exponential curve. Please do not change these fields unless instructed to do so, in the first instance please try to configure the scroll table for the scroll controls (via the Scroll Controls Option in the Configuration Dialog figure 2) If the box has been successfully connected the K8055 toolbar button will appear green. (See toolbar icon on second row, far right in figure 2) and the data LED on the front of the box will flash red when prompting and turning the wheel on the scroll control (figure 3)

5 figure 3 To configure the Box in the v1.5 QSeries Prompter Go to the tools menu option and select Options. Expand the Prompt Engine option and highlight Settings. Click on the KDriver Interface tab; If you are using a box with a Serial connection to the PC You ll need to select Stack DAQ Serial Box and change the COM port that the box is connected to. If the box is connected to the Prompter PC via a USB Cable then select K8055 USB Box. The Offset and Multiplier boxes are used to alter the scroll tables for the box, The defaults for these fields are Offset: 64 and Multiplier: 8 Multiplier Each scroll rate (from 0-255) will be multiplied by this figure to gain allow for faster scroll rates. Offset Each Scroll rate will have this offset added to it meaning the scroll table will be an exponential curve. Please do not change these fields unless instructed to do so, in the first instance please try to configure the scroll table for the scroll controls (via the Scroll Controls Option in the Configuration Dialog)

6 Technical Support is of prime importance to the management of Autocue, we therefore provide a 24-hour help line service to assist and advise. For more technical help or advice please call our 24-Hour Technical Support Help Line: Worldwide (except the Americas) +44 (0) Alternatively, us at: support@autocue.co.uk The Americas Alternatively, us at: support@autocuesystems.com

DLP USB Scroll Control. Configuration Guide for QBox

DLP USB Scroll Control. Configuration Guide for QBox DLP USB Scroll Control Configuration Guide for QBox Copyright information 2003-2014 Autocue Group Ltd. All rights reserved. All information about Autocue software, hardware and accessories including company