Snapshot. LEDrain 38 USER MANUAL. Ok on Dimmer. Outdoor OK. Sound Activated. DMX/Master/Slave. 115V/230V Switch. Replaceable Fuse.

Transcription

1 LEDrain 38 Snapshot Ok on Dimmer Outdoor OK Sound Activated DMX/Master/Slave 5V/30V Switch Replaceable Fuse User Serviceable Duty Cycle USER MANUAL CHAUVET, 3000 N 9 th Ct, Hollywood, FL 3300 U.S.A (800) (954) 99-5 FAX (954) /0:08

2 TABLE OF CONTENTS BEFORE YOU BEGIN... 3 WHAT IS INCLUDED... 3 UNPACKING INSTRUCTIONS... 3 AC POWER... 3 SAFETY INSTRUCTIONS... 3 INTRODUCTION... 4 FEATURES... 4 DMX CHANNEL SUMMARY... 4 PRODUCT OVERVIEW... 5 SETUP... 6 POWER... 6 MOUNTING... 6 OPERATING INSTRUCTIONS... 7 MASTER/SLAVE MODE... 7 Daisy Chain Connection... 7 Dipswitch Options... 7 DMX CONTROL MODE... 8 Setting the DMX address... 8 APPENDIX... 9 DMX PRIMER... 9 Fixture Linking... 9 DMX CHANNEL VALUES... 0 RETURNS PROCEDURE... CLAIMS... PHOTOMETRIC... DMX DIPSWITCH QUICK REFERENCE CHART... TECHNICAL SPECIFICATIONS... 3 TECHNICAL SUPPORT... 3 LEDrain 38 User Manual /0:08

3 BEFORE YOU BEGIN What is included x LEDrain 38 x Power cable ( m) and x Linking cable (.5 m) Warranty Card Users Manual Unpacking Instructions AC Power Immediately upon receiving a product, carefully unpack the carton, check the contents to ensure that all parts are present, and have been received in good condition. Notify the shipper immediately and retain packing material for inspection if any parts appear damaged from shipping or the carton itself shows signs of mishandling. Save the carton and all packing materials. In the event that a fixture must be returned to the factory, it is important that the fixture be returned in the original factory box and packing. This fixture has an auto-switching power supply that can accommodate a wide range of input voltages. The only thing necessary to do before powering on the unit is to make sure the line voltage you are applying is within the range of accepted voltages. This fixture will accommodate between 00V and 40V AC. All fixtures must be powered directly off a switched circuit and cannot be run off a rheostat (variable resistor) or dimmer circuit, even if the rheostat or dimmer channel is used solely for a 0% to 00% switch. Warning! All fixtures must be connected to circuits with a suitable Earth Ground. Safety Instructions Please read these instructions carefully, which includes important information about the installation, usage and maintenance? Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that they also receive this instruction booklet. Always make sure that you are connecting to the proper voltage and that the line voltage you are connecting to is not higher than that stated on decal or rear panel of the fixture. This product is intended for indoor use only! To prevent risk of fire or shock, do not expose fixture to rain or moisture. Make sure there are no flammable materials close to the unit while operating. The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent surfaces. Be sure that no ventilation slots are blocked. Always disconnect from power source before servicing or replacing lamp or fuse and be sure to replace with same lamp source. Secure fixture to fastening device using a safety chain. Never carry the fixture solely by its head. Use its carrying handles. Maximum ambient temperature is Ta: 40 C. Do not operate fixture at temperatures higher than this. In the event of serious operating problem, stop using the unit immediately. Never try to repair the unit by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please contact the nearest authorized technical assistance center. Always use the same type spare parts. Don t connect the device to a dimmer pack. Make sure power cord is never crimped or damaged. Never disconnect power cord by pulling or tugging on the cord. Avoid direct eye exposure to lamp while it is on. Caution! There are no user serviceable parts inside the unit. Do not open the housing or attempt any repairs yourself. In the unlikely event your unit may require service, please contact CHAUVET. LEDrain 38 User Manual 3 /8/007 0:00 AM

4 INTRODUCTION Features CONTROL FEATURES 7-channel DMX-5 LED narrow beam Blackout/static/dimmer/strobe Selector switch for sound active or automatic mode Static colors and RGB color mixing in master/slave mode via dip switches ADDITIONAL FEATURES Additional power output for daisy chaining units together (max 50 units) Built-in automated programs via master/slave Built-in sound activated programs via master/slave Double-bracket yoke doubles as floor stand Low power consumption OPTIONS Programmable: Any universal DMX-5 controller DMX Channel Summary CHANNEL INTENSITY CONTROL OF Red Green 3 Blue 4 Color Macros 5 Strobe/Speed 6 Programs 7 Dimmer LEDrain 38 User Manual 4 /8/007 0:00 AM

5 Product Overview Power Input Connector Fuse Holder DMX Connectors Power Link Out DMX dipswitches: DMX channel addressing Music/Auto switch Min-Max rotary knob Green LED Status ON - signifies the par can is set to be controlled via DMX OFF Par can is set to either Automatic or Sound Active mode as previously selected by the Music/Auto switch Hanging yoke also floor stand for uplighting. LEDrain 38 User Manual 5 /8/007 0:00 AM

6 Introduction SETUP Power This fixture has an auto-switching power supply that can accommodate a wide range of input voltages. The only thing necessary to do before powering on the unit is to make sure the line voltage you are applying is within the range of accepted voltages. This fixture will accommodate between 00V and 40V AC. To determine the power requirements for a particular fixture, see the label affixed to the back plate of the fixture or refer to the fixture s specifications chart. A fixture s listed current rating is its average current draw under normal conditions. All fixtures must be powered directly off a switched circuit and cannot be run off a rheostat (variable resistor) or dimmer circuit, even if the rheostat or dimmer channel is used solely for a 0% to 00% switch. All fixtures must be connected to circuits with a suitable Earth Ground. Power Cable Configuration CABLE PIN INTERNATIONAL BROWN Live L BLUE Neutral N YELLOW/GREEN Earth EG (Ground) Mounting Orientation This fixture may be mounted in any position provided there is adequate room for ventilation. Hanging Clamp (sold separately) Rigging The fixture includes a mounting yoke to which rigging clamp can be bolted.. Align the clamp screw with the center hole on the yoke and tighten.. Verify the structure can hold 0 times the weight of all to-be installed fixtures. 3. Adjust the angle on the yoke arm as necessary. LEDrain 38 User Manual /0:08

7 OPERATING INSTRUCTIONS The LEDrain 38 is a DMX-5 controllable, full RGB color mix par can made up of highly efficient and bright LEDS measuring 0mm in diameter. All red, green and blue LEDs can be controlled separately allowing the creation of an unlimited range of colors. The LEDrain 38 can operate in Stand-Alone, Master/Slave and via DMX-5 control utilizing 6 DMX channels. Master/Slave Mode The Master/Slave mode will allow you to link up to as many units you want in a daisy chain fashion. In this mode, the first unit in the daisy chain will automatically command all other units following.. Connect all LEDrain 38 units in a daisy chain fashion as described in the section following.. Dipswitch settings on slave fixtures are not required and will have no affect. 3. Set all dipswitches on the Master unit to the Off position and the unit will run it s built in color change program. OPTIONS - Set Music/Auto switch to Music and for sound-activated triggering of the program - Set Music/Auto switch to Auto then use the rotary dial to adjust speed of the program - See below under Dipswitch Options for additional program settings Daisy Chain Connection. Connect the (male) 3 pin connector side of the DMX cable to the output (female) 3 pin connector of the first fixture.. Connect the end of the cable coming from the first fixture which will have a (female) 3 pin connector to the input connector of the next fixture consisting of a (male) 3 pin connector. Then, proceed to connect from the output as stated above to the input of the following fixture and so on. Dipswitch Options FUNCTIONS DIPSWITCHES ( ON ) NOTES & DESCRIPTION Manual color -8 Color change program 8 Dipswitches -: Red level ( on = 50%, on = 75%, - on = 00%) Dipswitches 3-4: Green level ( on = 50%, on = 75%, - on = 00%) Dipswitches 5-6: Blue level ( on = 50%, on = 75%, - on = 00%) Music/Auto switch has no function in this mode Music/Auto switch Music: Sound Activated, Rotary knob sets sound sensitivity Auto: Rotary knob sets speed of program Very slow color cross-fade program 9 Music/Auto switch has no function in this mode LEDrain 38 User Manual 7 /8/007 0:00 AM

8 Appendix DMX Control Mode Operating in a DMX Control mode environment gives the user the greatest flexibility when it comes to customizing or creating a show. In this mode you will be able to control each individual trait of the fixture and each fixture independently. The LEDrain 38 uses 7 channels of control. Note: Dipswitch 0 must be turned on to activate DMX control mode. Note: Older 8-dipswitch version must have dipswitch 8 turned off to activate DMX control mode. Dipswitches -7 set the DMX address, and the maximum address is 7. Setting the DMX address This DMX mode enables the use of a universal DMX controller device. Each fixture requires a "start address" from to 5. A fixture requiring one or more channels for control begins to read the data on the channel indicated by the start address. For example, a fixture that occupies or uses 7 channels of DMX and was addressed to start on DMX channel 00, would read data from channels: 00, 0, 0, 03, 04, 05 and 06. Choose start addresses so that the channels used do not overlap and notate the start address selected for future reference. If this is your first time addressing a fixture using the DMX-5 control protocol than I suggest jumping to the Appendix Section and read the heading DMX Primer. It contains very useful information that will help you understand its use. Set the start address using the group of DIP switches located usually on bottom of the fixture. Each dip switch has an associated value. Adding the value of each switch in the ON position will provide the start address. Determining which switches to toggle ON given a specific start address can be accomplished in the following manner. By subtracting the largest switch value possible from the selected start address until zero is achieved. EXAMPLE STARTING ADDRESS Address 0 Pin # 4 = 8 Pin # = Total = 0 ON Address 4 Pin # 5 = 6 Pin # 4 = 8 Total = 4 ON Resolving address using simple math. Address (8) = 05, Turn ON Dip # 8 05 (64) = 4, Turn ON Dip # 7 4 (3) = 9, Turn ON Dip # 6 9 (8) =, Turn ON Dip # 4 () = 0, Turn ON Dip # You will most likely use the first available number which maybe number. This number was selected for example purposes. DIP SWITCH (DMX VALUE) LEDrain 38 User Manual /0:08

9 Appendix APPENDIX DMX Primer There are 5 channels in a DMX-5 connection. Channels may be assigned in any manner. A fixture capable of receiving DMX-5 will require one or a number of sequential channels. The user must assign a starting address on the fixture that indicates the first channel reserved in the controller. There are many different types of DMX controllable fixtures and they all may vary in the total number of channels required. Choosing a start address should be planned in advance. Channels should never overlap. If they do, this will result in erratic operation of the fixtures whose starting address is set incorrectly. You can however, control multiple fixtures of the same type using the same starting address as long as the intended result is that of unison movement or operation. In other words, the fixtures will be slaved together and all respond exactly the same. DMX fixtures are designed to receive data through a serial Daisy Chain. A Daisy Chain connection is where the DATA OUT of one fixture connects to the DATA IN of the next fixture. The order in which the fixtures are connected is not important and has no effect on how a controller communicates to each fixture. Use an order that provides for the easiest and most direct cabling. Connect fixtures using shielded two conductor twisted pair cable with three pin XLR male to female connectors. The shield connection is pin, while pin is Data Negative (S-) and pin 3 is Data positive (S+). CHAUVET carries 3-pin XLR DMX compliant cables, DMX-0 (33 ), DMX-4.5 (5 ) and DMX-.5 (5 ) Fixture Linking DMX connector configuration COMMON DMX + INPUT 3 3 OUTPUT Termination reduces signal errors and to DMX - avoid signal transmission problems and interference, it is always advisable to connect a DMX signal terminator. Note! If you use a controller with a 5 pin DMX output connector, you will need to use a 5 pin to 3 pin adapter. CHAUVET Model No: DMX5M. The chart below details a proper cable conversion: 3 Resistance 0 ohm /4w between pin (DMX -) and pin 3 (DMX +) of the last fixture. 3 PIN TO 5 PIN CONVERSION CHART Conductor 3 Pin Female (output) 5 Pin Male (Input) G round/shield Pin Pin Data ( - )signal Pin Pin Data ( + ) signal Pin 3 Pin 3 Do not use Do not use Do not use Do not use LEDrain 38 User Manual /0:08

10 Appendix DMX Channel Values CHANNEL VALUE FUNCTION NOTES Red: ( 0% ~ 00% ) Green: ( 0% ~ 00% ) Blue: ( 0% ~ 00% ) Macro Colors (By LED levels) Off Red: 00% Green: 0% Blue: Red: 00% Green: 40% Blue Red: 00% Green: 60% Blue: Red: 00% Green: 80% Blue: Red: 00% Green: 00% Blue: Red: Green: 00% Blue: Red: Green: 00% Blue: 0% Red: Green: 00% Blue: 40% Red: Green: 00% Blue: 60% Red: Green: 00% Blue: 80% Red: Green: 00% Blue: 00% Red: Green: Blue: 00% Red: 0% Green: Blue: 00% Red: 40% Green: Blue: 00% Red: 60% Green: Blue: 00% Red: 80% Green: Blue: 00% Red: 00% Green: Blue: 00% Red: 00% Green: 5% Blue: 00% Red: 00% Green: 50% Blue: 00% Red: 00% Green: 75% Blue: 00% Red: 00% Green: 00% Blue: 00% Red: 00% Green: 00% Blue: 5% Red: 00% Green: 00% Blue: 50% Red: 00% Green: 00% Blue: 75% Red: 00% Green: 00% Blue: 00% Red: 0% Green: 00% Blue: 00% Red: 40% Green: 00% Blue: 00% Red: 60% Green: 00% Blue: 00% Red: 80% Green: 00% Blue: 00% Red: 00% Green: 00% Blue: 00% Red: 50% Green: 50% Blue: 50% Strobe or Speed: ( 0% ~ 00% ) Preset Programs No Function Fade Program: Use Ch 5 to adjust speed Color Chase: Use Ch5 to adjust speed Color Chase: Use rotary knob to adjust speed Dimmer: ( 0% ~ 00% ) LEDrain 38 User Manual /0:08

11 Appendix Returns Procedure Claims Photometrics Returned merchandise must be sent prepaid and in the original packing, call tags will not be issued. Pac kage must be clearly labeled with a Return Merchandise Authorization Number (RA #). Products returne d without an RA # will be refused. Call CHAUVET and request RA # prior to shipping the fixt ure. Be prepared to provide the model number, serial number and a brief description of the cause for the re turn. Be sure to properly pack fixture, any shipping damage resulting from inadequate packaging is the customer s responsibility. CHAUVET reserves the right to use its own discretion to repair or replace product(s). As a suggestion, proper UPS packing or double-boxing is always a safe method to use. Damage incurred in shipping is the responsibility of the shipper; therefore the damage must be reported to the carrier upon receipt of merchandise. It is the customer's responsibility to notify and submit claims with the shipper in the event that a fixture is damaged due to shipping. Any other claim for items such as missing component/part, damage not related to shipping, and concealed damage, must be made within seven (7) days of receiving merchandise. 9 Beam Angle Foot Candles 4 LUX Distance (feet) 3 Distance (meters) LEDrain 38 User Manual /0:08

12 DMX Dipswitch Quick Reference Chart DMX Address Quick Reference Chart Dip Switch Position DMX DIP SWITCH SET # =OFF # =ON # X=OFF or ON # # # #3 #4 # Dip Switch Position DMX Address LEDrain 38 User Manual /8/007 0:00 AM

13 Technical Specifications WEIGHT & DIMENSIONS Length in (9 mm) Width in (73 mm) Height in (35 mm) Weight... lbs (0.5kg) POWER Auto-s witc hing power supp ly V 40V 50/60 Hz AC Power consumptio n... W Inrush... 8W Power output connector units max LIGHT SOURCE LE D Total, (36 Red, 36 Green, 36 Blue) 00, 000hr PHOTOMETRIC Be am Angle Fie ld A ngle Photom etric chart... See page FUSE Main... 0mm Glass A Fast Blow CONTROL & PROGRAMMING Data input... locking 3-pin XLR male socket Da ta output locking 3-pin XLR female socket Da ta pin configuration...pin shield, pin (-), pin 3 (+) Protocols... DMX-5 USITT DM X Channels...7 ORDERING INFORMATION LE Drain LEDrain 38 Technical Support Address: Service Dept N 9th Ct, Hollywood, FL 3300 (U.S.A.) Support ( ): tech@chauvetlightin g.com Telephone: (954) (Press 4) Fax: ( 954) (Attention: Service) Website: LEDrain 38 User Manual 3 /8/007 0:00 AM