Design LED 60 Strip. Elation Professional 4295 Charter Street Los Angeles, Ca Rev. 01/29/07

Transcription

1 Design LED 60 Strip Elation Professional 4295 Charter Street Los Angeles, Ca Rev. 01/29/07

2 TABLE OF CONTENS CONTENTS 1. General Information 3 a. Introduction. 3 b. Unpacking c. Customer Support. 3 d. Warranty Registration Safety Instructions Features 7 4. General Guidelines Fixture Overview Mounting and Installation.. 11 a. Yoke Assembly.. 11 b. Mounting Positions 13 c. Mounting Points. 13 d. Securing Understanding DMX a. DMX Connections. 16 b. DMX Terminator. 17 c. 3-Pin to 5-Pin Conversion. 17 d. Understanding DMX Addressing Operation Modes. 19 a. DMX Mode Selection. 19 b. Manual Settings DMX Traits 22 a. 6-Channel Mode 23 b. 12-Channel Mode.. 24 c. 15-Channel Mode.. 26 d. DMX Dipswitch Reference Chart Cleaning and Maintenance Warranty Photometric Data Dimensional Drawings Circuit Schematic Technical Specifications Elation Professional, Los Angeles Ca. 1

3 1. GENERAL INFORMATION INTRODUCTION: Congratulations, you have just purchased one of the most innovative and reliable LED fixtures on the market today! The Design LED 60 Strip, has been designed to perform reliably for years when the guidelines in this booklet are followed. Please read and understand the instructions in this manual carefully and thoroughly before attempting to operate this unit. These instructions contain important information regarding safety during use and maintenance. UNPACKING: Thank you for purchasing the Design LED 60 Strip by Elation Professional. Every Design LED 60 Strip has been thoroughly tested and has been shipped in perfect operating condition. Carefully check the shipping carton for damage that may have occurred during shipping. If the carton appears to be damaged, carefully inspect your fixture for damage and be sure all accessories necessary to operate the fixture have arrived intact. In the event damage has been found or parts are missing, please contact our customer support team for further instructions. Please do not return this unit to your dealer without first contacting customer support at the number listed below. Inside the box you should find: the fixture, a DMX XLR cable, an IEC power cable, an IEC jumper power cable, a safety cable, and this manual. Please contact customer support at the number listed below if any of the above items are missing. CUSTOMER SUPPORT: Elation Professional provides a customer support line, to provide set up help and to answer any question should you encounter problems during your set up or initial operation. You may also visit us on the web at for any comments or suggestions. For service related issue please contact Elation Professional. Service Hours are Monday through Friday 9:00 a.m. to 5:00 p.m. Pacific Standard Time. Voice: (323) Fax: (323) support@elationlighting.com Forum: Warning! To prevent or reduce the risk of electrical shock or fire, do not expose this unit to Elation Professional, Los Angeles Ca. 2

4 rain or moisture. Caution! There are no user serviceable parts inside this unit. Do not attempt any repairs yourself. Doing so will void your manufactures warranty. Please do not discard the shipping carton in the trash. Please recycle whenever possible. WARRANTY REGISTRATION: The Design LED 60 Strip carries a two year (730 days) limited warranty. Please fill out the enclosed warranty card to validate your purchase. All returned service items whether under warranty or not, must be freight pre-paid and accompany a return authorization (R.A.) number. The R.A. number must be clearly written on the outside of the return package. A brief description of the problem as well as the R.A. number must also be written down on a piece of paper and included in the shipping container. If the unit is under warranty, you must provide a copy of your proof of purchase invoice. Items returned without a R.A. number clearly marked on the outside of the package will be refused and returned at customer s expense. You may obtain a R.A. number by contacting customer support at (323) Elation Professional, Los Angeles Ca. 3

5 2. SAFETY INSTRUCTIONS To guarantee proper and consistent operation, it is important to follow the guidelines in this manual. Elation Professional will not accept responsibility for damages resulting from the misuse of this fixture due to the disregard of the information printed in this manual. 1. Always be sure that the fan and the air inlets remain clean and are never blocked. Allow about 6 (15cm) between this fixture and other devices or a wall to allow for proper cooling. 2. Never touch the fixture during normal operation. 3. Never look directly into the lamp beam. You risk injury to your retina, which may induce blindness. 4. For safe operation, follow the Installation guide described in chapter two of this manual. Operating the Design LED 60 Strip without suited safety aids such as safety cables or clamps can increase the risk of damage and/or personal injury. 5. Installation should only be performed by qualified and certified personal. 6. When mounting this fixture, use only the original rigging points included with this fixture. Any structural modification will void the original manufactures warranty and may increase the risk of damage and/or personal injury. 7. To reduce the risk of fire or shock, do not expose this fixture to rain or moisture. 8. Do not attempt to operate this fixture if the power cord has become damaged or frayed. 9. Never open this fixture while in use. 10. This device falls under protection-class I. Therefore it is essential that the device be grounded properly. 11. All electrical connections must performed by qualified personal. 12. Be sure the available voltage matches the voltage requirements of the unit. Be Elation Professional, Los Angeles Ca. 4

6 sure the power cord is never crimped or damaged. If the power cord is damaged, replace it immediately with a new one of similar power rating. 13. Always disconnect from main power before performing any type of service or any cleaning procedure. 14. Only handle the power cord by the plug. Never pull out the plug by tugging the wire portion of the cord. 15. Please be aware that damages caused by modifications to the device are not subject to warranty. Important Notice: Damages resulting from the disregard of safety and general user instructions found in this user manual are not subject to any warranty claims. Never touch the device during operation! The housing may heat up Never look directly into the light source, as sensitive persons may suffer an epileptic shock. Elation Professional, Los Angeles Ca. 5

7 3. FEATURES Low power consumption Minimal heat emission Maintenance free operation Equipped with 60 one-watt LEDs: (20 red, 20 green, 20 blue) High power LEDs manufactured by Lumileds, USA 100,000 hours rated LED life Seamless RGB color changing USITT DMX-512 complaint 5-pin and 3-pin Male and Female XLR Data Connectors Preprogrammed colored macros Strobe-effect with a maximum flash rate of 18fps DMX-controlled operation or stand-alone operation with Master/Slave-function 8 built-in programs accessed via DMX-controller or manually Sound-controlled via built-in microphone Individual control over each LED Electronic/Switching power supply (90v~120V 50/60Hz) Three DMX Modes: 63 DMX-channels 60 DMX-channel 15 DMX-channel 6 DMX-channel Flicker-free operation for television and film Compact design: fits in 12 box truss Brilliant light output Linkable power supply (in and out power connectors) up to 8 units. Elation Professional, Los Angeles Ca. 6

8 4. GENERAL GUIDELINES This fixture is a professional lighting effect designed for use on stage, in nightclubs, in theatres, and other types of architectural installations. Do not attempt operation or installation without a proper knowledge on how to do so. This fixture was designed for indoor use only; use of this fixture outside will void the manufacture s warranty. Consistent operational breaks will ensure that the fixture will function properly for many years to come. Do not shake the fixture around. Avoid brute force when installing or operating the fixture. While choosing an installation location, please be sure that the fixture will not be exposed to extreme heat, moisture, or dust. The minimum distance between the fixture and a wall or flat surface should be at least.5 meter (about 1.5ft). Always install the fixture with an appropriately rated safety cable. When installing the fixture in a suspended environment always be sure to use mounting hardware no less than M10 x 25 mm, also be sure the hardware is only inserted in the yoke s mounting holes. Do not attempt to operate this fixture until you have familiarized yourself with all of its functions. Do not permit operation by persons not qualified for operating this type of theatrical fixture. Most damages are the result of improper operation. Please use the original packaging to transport the fixture in for service. For your own safety, please read this user manual carefully before installing the device. Elation Professional, Los Angeles Ca. 7

9 5. FIXTURE OVERVIEW 1. Bracket Locking Knob This knob is used to secure the bracket in place after angle adjustments have been made. 2. Diffusing Lens This lens is used to both protect the LEDs as well as diffuse the light output. 3. LED Assembly RGB LED assembly 3x1watt LEDs 4. DMX Input Jack This jack accepts an incoming DMX signal via a male, 3-pin or a 5-pin XLR jack. 5. DMX Output Jack This jack is used to send an incoming DMX signal to the next fixture in the DMX chain via a female, 3-pin or a 5-pin XLR jack. 6. Power Output Jack Use this jack to jump power to another Design LED 60 Strip. 7. Power Input/Fuse Holder Assembly This assembly holds the safety fuse as well Elation Professional, Los Angeles Ca. 8

10 as provides a female IEC connector for a power cord. Always replace the fuse with an exact match unless otherwise specified by an authorized Elation Service Technician. Using a fuse other than that specified could seriously damage the unit and will void your manufactures warranty. 8. On/Off Power Switch Controls main power to the unit. 9. Dipswitch Assembly These dipswitches are used to set the DMX address, master slave settings, and other special functions. See the dipswitch chart on page 16 for more information on the dipswitch functions. 10. Hanging Bracket The unit uses a unique sectional bracket that allows the unit to be hung, mounted, or stood straight up. Elation Professional, Los Angeles Ca. 9

11 6. MOUNTING AND INSTALLATION Yoke Assembly Single Unit Operation (DLED 12 Brick shown for illustration purposes only). The device can be placed directly on the stage floor or rigged in any orientation on a truss without altering its operation characteristics. When connecting the hanging yoke to the fixture, refer to the illustration below. Cautions: For added protection mount the fixtures in areas outside walking paths, seating areas, and away from areas were the fixture might be reached by unauthorized personal. Before mounting the fixture to any surface, make sure that the installation area can hold a minimum point load of 10 times the device s weight. Fixture installation must always be secured with a secondary safety attachment, such as an appropriate safety cable. To avoid injury, never stand directly below the device when mounting, removing, or servicing the fixture. Refer to regulations BGV C1 (formerly VBG 70) and DIN VDE for proper installation in Europe To ensure proper installation, only qualified staff should attempt installation. Mounting points Elation Professional, Los Angeles Ca. 10

12 Overhead mounting requires extensive experience, including amongst others calculating working load limits, a fine knowledge of the installation material being used, and periodic safety inspection of all installation material and the fixture. If you lack these qualifications, do not attempt the installation yourself. Improper installation can result in bodily injury. Be sure to complete all rigging and installation procedures before connecting the main power cord to the appropriate wall outlet. Mounting The Design LED 60 Strip is fully operational in three different mounting positions, hanging upside-down from a ceiling, side mounted, or set on a flat level surface. Be sure this fixture is kept at least 0.5m away from any flammable materials (decoration etc.). When clamp mounting; always use and install the supplied safety cable as an added safety measure to prevent accidental damage in the event of a clamp failure. See the image below. Elation Professional, Los Angeles Ca. 11

13 CAUTION! Be sure all electrical connections are performed by a qualified electrician before attempting any operation. Clamp Mounting The Design LED 60 Strip provides a unique mounting bracket assembly that allows the unit to stand on flat surface, hang on truss via a clamp, or be used in cluster allow multiple units to rigged together (see the illustration below). Regardless of the mounting option you choose please refer to the safety guidelines in this manual to avoid damage to the unit and/or injury to persons. When mounting this fixture to truss be sure to secure an appropriately rated clamp to the hanging yoke using a M10 screw fitted through the center hole of the hanging yoke. As an added safety measure be sure to attach at least one properly rated safety cable to the Elation Professional, Los Angeles Ca. 12

14 fixture. See illustration below. Securing the Design LED 60 Strip Always secure your fixture with a safety cable when suspending the unit from truss or other means. The fixture provides a built-in rigging point for a safety cable as illustrated above. Be sure to only use the designated rigging point for a safety cable. Never secure a safety cable to the hanging bracket. Elation Professional, Los Angeles Ca. 13

15 7. UNDERSTANDING DMX Data Cable (DMX Cable) Requirements (For DMX and Master/Slave Operation): Your fixture and your DMX controller require a standard 3-pin XLR connector for data input and data output (see figure below). Be sure to only use properly rated DMX cables for DMX operation and not standrd audio cables. If you are constructing your own cables be sure to use two conductor shielded digital cable rated at a 120 ohms (this cable can be purchased at almost all professional sound and lighting stores). Your cables should be made with a male and female 3-pin XLR connector on either end of the cable. Please note: This is not the same as audio microphone cable. Audio cable has a different resistance rating Be sure to follow the above figure when making your own cables. Do not use the ground lug on the XLR connector. Do not connect the cable s shield conductor to the ground lug or allow the shield conductor to come in contact with the XLR s outer casing. Grounding the shield could cause a short circuit and erratic behavior. DMX-512 control connection Connect the provided DMX XLR cable to the female 3-pin XLR output of your controller and the other side to the male 3-pin XLR input of the moving head (Please refer to the diagram below.). You can chain multiple moving heads together through serial linking. The cable needed should be two conductor, shielded cable with XLR input and output connectors. Elation Professional, Los Angeles Ca. 14

16 Always be sure daisy chain your in and out data connections, never split or Y your DMX connections unless you are using an approved DMX splitter such as the Elation Opto Branch 4 or DMX Branch/4. DMX-512 connection with DMX terminator When longer runs of cable are used, you may need to use a terminator on the last fixture to avoid erratic behavior. A terminator is a 120 ohm 1/4 watt resistor that is connected between pins 2 and 3 of a male XLR connector (DATA + and DATA -). This fixture is inserted in the female XLR connector of the last fixture in your daisy chain to terminate the line. Using a cable terminator (Elation part number Z-DMX/T) will decrease the possibilities of erratic behavior. 5-Pin XLR DMX Connectors. Some manufactures use 5-pin XLR connectors for DATA transmission in place of 3-pin. 5-pin XLR fixtures may be implemented in a 3-pin XLR DMX line. When inserting standard 5-pin XLR connectors in to a 3-pin line a cable adaptor must be used, these adaptors are readily available at most electric stores. The chart on the next page details a proper cable conversion. Elation Professional, Los Angeles Ca. 15

17 Understanding Fixture DMX addressing; All fixtures should be given a DMX starting address when using a DMX controller, so the correct fixture responds to the correct control signal. This digital starting address is the channel number from which the fixture starts to listen to the digital control information sent out from the DMX controller. The allocation of this starting DMX address is achieved by combining various dipswitches located on the rear of the fixture. You can set the same starting address for all fixtures, or a group of fixtures, or set different address for each individual fixture. Be advised that setting all you fixtures to the same DMX address will subsequently control all fixtures in the same fashion, in other words, changing the settings of one channel will affect all the fixtures simultaneously. If you set each fixture to a different DMX address, each unit will start to listen to the channel number you have set, based on the quantity of control channels (DMX channels) of each fixture. That means changing the settings of one channel will only affect the selected fixture. Elation Professional, Los Angeles Ca. 16

18 In the case of the Design LED 60 Strip, which is a 15 channel fixture (default), you should set the starting DMX address of the first unit to 1, the second unit to 16 (15 + 1), the third unit to 31 ( ), and so on. The chart on page 24 details the proper starting DMX address dipswitch setting combination. NOTE: The Design LED 60 Strip contains a total of 12 dipswitches. Only use dipswitches 1~9 to set the DMX address. Dipswitches 10~12 are used for special functions that will be explained on the next page. Elation Professional, Los Angeles Ca. 17

19 8. OPERATING MODES This fixture can run in three different DMX modes, the following pages will detail the different operating modes as well as how to achieve the different operating modes. DMX Settings: The chart below describes how to access the different DMX modes. The chart below also defines the how the channel will function in the different DMX modes. DMX operation mode DIP# 11 DIP#12 LED control Mode 63CH OFF OFF Each LED can be run individually 60CH ON OFF Each LED can be run individually 15CH OFF ON Every 5 LEDs to be run in sync 6CH ON ON R,G,B run by group LEDs control channels Preset programs channel Strobe channel Master dimming/program speed 1~ ~60 1~ ~ Dipswitches 11 & 12: DMX Mode Selection, See the chart above; 63, 60, 15, or 6 channel modes. Dipswitch 10: Sound-active operation, when dipswitch 10 is in the ON position the unit will change colors when it detects an audible sound. This function work in either stand-alone unit or master/slave modes. Manual Settings: The chart below details the dipswitch setting for various manual settings. Manual static colors are achieved when dipswitch 7 is in the off position. Follow the dipswitch settings below to achieve various static colors by combining different color LEDs with various intensity levels. RED: Dipswitch 1 & 2 off, the red value is 0 Dipswitch 1 is on and dipswitch 2 is off, the red value is 60 Dipswitch 1 is off and dipswitch 2 is on, the red value is 125 Elation Professional, Los Angeles Ca. 18

20 Dipswitch 1 is on and dipswitch 2 is on, the red value is 255 GREEN: Dipswitch 3 & 4 off, the green value is 0 Dipswitch 3 is on and dipswitch 4 is off, the green value is 60 Dipswitch 3 is off and dipswitch 4 is on, the green value is 125 Dipswitch 3 is on and dipswitch 4 is on, the green value is 255 BLUE: Dipswitch 5 & 6 is off, the blue value is 0 Dipswitch 5 is on and dipswitch 6 is off, the blue value is 60 Dipswitch 5 is off and dipswitch 6 is on, the blue value is 125 Dipswitch 5 is on and dipswitch 6 is on, the blue value is 255 When dipswitch 7 is set to the ON position internal program will be activated. When dipswitch 7 is in the OFF position dipswitches 1~6 are used to access the different internal programs. Please see the chart below for detailed information on accessing the internal programs: Dipswitch # 10 is OFF, Dipswitch #11 is ON, and Dipswitch #7 is ON, the fixture will run the internal programs. Dipswitches 1 & 7 on accesses internal program 1 Dipswitches 2 & 7 on accesses internal program 2 Dipswitches 3 & 7 on accesses internal program 3 Dipswitches 4 & 7 on accesses internal program 4 Dipswitches 5 & 7 on accesses internal program 5 Dipswitch 6 & 7 on accesses internal program 6 Dipswitch 1,2 & 7 on accesses internal program 7 Dipswitch 1,3 & 7 on accesses internal program 8 The chart below details the different speed settings available for the internal programs when the fixture is running in manual mode. The program speed can be adjusted using dipswitches 8 and 9: Speed Dipswitch #8 Dipswitch #9 Slow (1.1s between scenes) OFF OFF Medium (0.6s between scenes) ON OFF Fast (0.2s between scenes) OFF ON Very fast (0.1s between scenes) ON ON Elation Professional, Los Angeles Ca. 19

21 The chart below visual represents the dipswitch setting listed in the previous section. Operating Mode: Dip # 11 Dip #10 Dip #9 Dip #8 Dip #7 No function OFF OFF N/A N/A N/A N/A N/A N/A N/A N/A N/A Dip #6 Dip #5 Dip #4 Dip #3 Dip #2 Dip #1 Sound control- Stand Alone Static R, G, B (Refer to Table 3) Preset Program 1 Preset Program 2 Preset Program 3 Preset Program 4 Preset Program 5 Preset Program 6 Preset Program 7 Preset Program 8 OFF ON N/A N/A N/A N/A N/A N/A N/A N/A N/A ON OFF N/A N/A OFF Blue Blue Green Green Red Red ON OFF Speed Speed ON OFF OFF OFF OFF OFF ON ON OFF ON OFF OFF OFF OFF ON OFF ON OFF ON OFF OFF OFF ON OFF OFF ON OFF ON OFF OFF ON OFF OFF OFF ON OFF ON OFF ON OFF OFF OFF OFF ON OFF ON ON OFF OFF OFF OFF OFF ON OFF ON OFF OFF OFF OFF ON ON ON OFF ON OFF OFF OFF ON OFF ON DMX Operation Notes: The fixture will automatically function in DMX mode whenever the unit receives a DMX signal. Please note that this will override all manual settings regardless of dipswitch positions. This unit will keep and retain the last DMX command in the event of DMX signal failure. To reset the fixture you must turn the power off. Elation Professional, Los Angeles Ca. 20

22 9. DMX CHANNEL TRAITS 6 Channel Mode: This chart details a simple layout of the DMX channel assignment in 6- channel mode. The chart traits will vary slightly for 63-channel, 60-chennel, and 15-channel operation, as those modes use more RGB channels for more precise control. CHANNEL 1:Red CHANNEL 2:Green CHANNEL 3:Blue CHANNEL 4: Internal programs: CHANNEL 5:Strobe CHANNEL 6: Dimming (0%-100%) Elation Professional, Los Angeles Ca. 21

23 DMX channel s functions and their values (6 Channel Mode): Channel 1 - Red: Red (0-Black, % Red) Channel 2 - Green: Green (0-Black, % Green) Channel 3 - Blue: Blue (0-Black, % Blue) Channel 4 - Internal programs: 0-10 No function Internal program Internal program Internal program Internal program Internal program Internal program Internal program Internal program 8 Channel 5 - Strobe: 0 No function 1~95 Strobe effect slow to fast No function Pulse effect in sequences No function Random strobe effect slow to fast No function Elation Professional, Los Angeles Ca. 22

24 Channel 6 - General dimming / Program Speed Control This channel has two functions depending on the operating mode. When running the built-in Programs this channel will control the program speed Dimming (0%-100%) ~ Normal Operation Speed (min to max) ~ When running built-in programs on channel 4 Elation Professional, Los Angeles Ca. 23

25 Elation Professional, Los Angeles Ca. 24

26 10. CLEANING AND MAINTENANCE The consider the following point during normal service and inspection: 1. Be sure all screws and fasteners are securely tightened at all times. Lose screws may fall out during normal operation resulting in damage or injury as larger parts could fall. 2. Electric power supply cables must not show any damage, material fatigue or sediments. Never remove the ground prong from the power cable. Further instructions depending on the installation spot and usage have to be adhered by a skilled installer and any safety problems have to be removed. Disconnect from mains before starting maintenance operation. We recommend a frequent cleaning of the device. Please use a moist, lint- free cloth. Never use alcohol or solvents. There are no user serviceable parts inside this, please refer all other service issues to an authorized Elation service technician. Should you need any spare parts, please order genuine parts from your local dealer. Elation Professional, Los Angeles Ca. 25

27 11. 2-YEAR LIMITED WARRANTY A. Elation Professional hereby warrants, to the original purchaser, Elation Professional products to be free of manufacturing defects in material and workmanship for a period of two years, (730 days) from the date of purchase. This warranty shall be valid only if the product is purchased within the United States of America, including possessions and territories. It is the owner s responsibility to establish the date and place of purchase by acceptable evidence, at the time service is sought. B. For warranty service, send the product only to the Elation Professional factory. All shipping charges must be pre-paid. If the requested repairs or service (including parts replacement) are within the terms of this warranty, Elation Professional will pay return shipping charges only to a designated point within the United States. If the entire instrument is sent, it must be shipped in its original package. No accessories should be shipped with the product. If any accessories are shipped with the product, Elation Professional shall have no liability what so ever for loss of or damage to any such accessories, nor for the safe return thereof. C. This warranty is void if the serial number has been altered or removed; if the product is modified in any manner which Elation Professional concludes, after inspection, affects the reliability of the product; if the product has been repaired or serviced by anyone other than the Elation Professional factory unless prior written authorization was issued to purchaser by Elation Professional ; if the product is damaged because not properly maintained as set forth in the instruction manual. D. This is not a service contract, and this warranty does not include maintenance, cleaning or periodic check-up. During the period specified above, Elation Professional will replace defective parts at its expense, and will absorb all expenses for warranty service and repair labor by reason of defects in material or workmanship. The sole responsibility of Elation Professional under this warranty shall be limited to the repair of the product, or replacement thereof, including parts, at the sole discretion of Elation Professional. All products covered by this warranty were manufactured after January 1, 1990, and bare Elation Professional, Los Angeles Ca. 26

28 identifying marks to that effect. E. Elation Professional reserves the right to make changes in design and/or improvements upon its products without any obligation to include these changes in any products theretofore manufactured. F. No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with products described above. Except to the extent prohibited by applicable law, all implied warranties made by Elation Professional in connection with this product, including warranties of merchantability or fitness, are limited in duration to the warranty period set forth above. And no warranties, whether expressed or implied, including warranties of merchantability or fitness, shall apply to this product after said period has expired. The consumer s and or Dealer s sole remedy shall be such repair or replacement as is expressly provided above; and under no circumstances shall Elation Professional be liable for any loss or damage, direct or consequential, arising out of the use of, or inability to use, this product. G. This warranty is the only written warranty applicable to Elation Professional Products and supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore published. Elation Professional, Los Angeles Ca. 27

29 12. PHOTOMETRIC DATA Elation Professional, Los Angeles Ca. 28

30 13. DIMENSIONAL DRAWINGS Elation Professional, Los Angeles Ca. 29

31 14. CIRCUIT SCHEMATIC Elation Professional, Los Angeles Ca. 30

32 15. TECHNICAL SPECIFICATIONS Power supply: Power consumption: LED Configuration: Packing dimensions: Weight: DMX Channels: 90~260v AC, 50Hz~60Hz MAX 140w 60 1Watt Units (20 x Red, 20 x Green 20 x Blue) x14.5x 21.5cm 10.5.Kgs 6, 15, 60, or 63, DMX Channel modes Drive: Standard DMX-512, 3 pole XLR; [+] = Pin 3, [-] = Pin 2, [Ground] = Pin 1 or Standard DMX-512,5 pole XLR; n/a = Pin 5, n/a = Pin 4, [+] = Pin 3, [-] = Pin 2, [Ground] = Pin Color Mixing: RGB Color Additive Mixing Beam Angle: 80 Fuse: GMA 220v~4A Dimmer: Continuous Dimming 0~100% Strobe: Electronic Strobe 0~18 Fps Lamp Life: 100,000 Hours Rated Life Please Note: Specifications and improvements in the design of this unit and this manual are subject to change without any prior written notice. Elation Professional, Los Angeles Ca. 31

33 Elation Professional, Los Angeles Ca. 32

34 Elation Professional 4295 Charter Street Los Angeles, CA / fax /Info@ElationLighitng.com Elation Professional, Los Angeles Ca. 33