GENUINE PARTS INSTALLATION INSTRUCTIONS
|
|
- Estella Newman
- 7 years ago
- Views:
Transcription
1 GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION: Accent light Kit APPLICATION: Versa (2010) PART NUMBER: 999F3 AW000 - Universal Accent Lighting Kit. 4. KIT CONTENTS: Item QTY Description Service Part Number A 1 Control module 999F3 AW004 B 1 Encoder and harness assembly 999F3 AW006 C 1 Foot well lights and harness assembly 999F3 AW001 D 1 Cup holder lights and harness assembly 999F3 AW003 E 1 Harness Vehicle interface 999F3 AW005 F 1 Control Knob 999F3 AW002 G 1 Kit contents list at end of installation instructions 5. TOOLS REQUIRED Trim stick Ratchet and 6" extension 10mm, 11mm & 13mm sockets 5/16", 3/16" and 9/32" drill bits, drill stop. #2 Philips screwdriver T-20 Torx bit Protective cloth Scissors Metric ruler Electrical tape, masking tape. 6. PRE-INSTALLATION CAUTION/NOTES Dealer installation recommended. Instructions may refer to Service Manual Installation may require special tools This part is to be installed at a surface temperature no warmer than ºF Remove and prepare templates located at the end of Installation Instructions CAUTION This accessory must only be installed as specified in these instructions. Ensure at all times that parts are securely fitted and will not compromise the safe function of vehicle systems. Page 1 of F3 4W010II - Rev
2 7. GENERAL SYSTEM OVERVIEW Fit-up 2 action points: - Prepare exploded view drawing of vehicle interior with fixings detail (clip, screw, bolt etc). 8. CRITICAL STEPS: The following steps are critical and must be performed EXACTLY as specified to ensure proper installation Location of the lights must be followed exactly as described in this instruction Posi-Tap instructions must be specifically followed as described. Cables must be properly secured to prevent rattling and/or snagging on any moving parts or limbs e.g. cup holder harness running through centre console close to handbrake Page 2 of F3 4W010II - Rev
3 9. VEHICLE PREPARATION 1) Vehicle Preparation a) Reecord customer radio presents A B C b) Apply parking brake c) Turn off the ignition d) Disconnect battery negative terminal NOTE: USE CAUTION WHEN REMOVING/RE-INSTALLING TRIM COMPONENTS TO AVOID DAMAGE, SCRATCHES, BREAKING OF CLIPS AND/OR INTERIOR TRIM PANELS. MOVE ALL TRIM COMPONENTS TO A PROTECTED AREA. 2) Remove the following interior parts as shown. Refer to the vehicle service manual. a) Console mask b) Console mask cover Note: For M/T remove shift knob c) Console rear finisher d) LH and RH instrument lower covers e) Shifter finisher f) Console body ass'y g) Center console h) Fuse block lid i) Side mask LH j) Instrument side finisher k) Instrument lower finisher l) Glove box assembly m) Rear cup holder. Page 3 of F3 4W010II - Rev
4 10. LIGHT STICK PREPARATION Before LED side 1) Prepare driver side light stick. a) Clean mounting area with alcohol wipe. Loop Fig. 1 After LED side b) Fix (1) 12.5 x 19 x 0.7mm adhesive pad with edge aligned to position 3 as shown- on LED side. c) Fix (1) 12.5 x 19 x 0.7mm adhesive pad with edge aligned to position 10 as shown - on LED side Fig. 1 (cont'd) Before LED side 2) Prepare passenger side light stick. a) Clean mounting area with alcohol wipe. Fig. 2 After LED side b) Fix (1) 12.5 x 19 x 0.7mm adhesive pad with edge aligned to position 1 as shown - on LED side. c) Fix (1) 12.5 x 19 x 0.7mm adhesive pad with edge aligned to position 11.5 as shown - on LED side. 1 Fig. 2 (cont'd) Page 4 of F3 4W010II - Rev
5 11. INSTALLATION PROCEDURE: 1) Remove (4) Philips screws attaching Cupholder. CAUTION Use only a 9/32" drill to avoid damage to Cupholder. Holes larger than 9/32" will not retain LEDs. Use a drill stop to avoid damage to the Cupholder. 2) Prepare Cupholder for LEDs. a) Tape LED template (A) to cupholder. b) Mark and drill (2) 9/32" holes. c) Snap in Cupholder LED Lenses and lens retainers. 3) Prepare Cupholder for Encoder. a) Tape Encoder template (B) to cupholder. b) Mark and drill (1) 5/16" hole. Page 5 of F3 4W010II - Rev
6 11. INSTALLATION PROCEDURE: Fig. 4 4) Install Cupholder LEDs and Encoder. a) Clean mouting area with alcohol wipe. b) Peel double-sided tape liner and place each Cupholder light assembly as shown. c) Secure cable with foam tape as shown. Fig. 4 (cont'd) d) Install Encoder, 11mm Lock Nut and Knob. e) Route LED wires next to Encoder wires and install 4" cable tie. f) Reinstall Cupholder and (4) Phillips screws to center console. Fig. 5 5) Prepare Instrument Lower Finisher. 5mm 50mm 15mm 5mm a) Align long bracket to finisher rib and bracket hold to finisher edge as shown. Mark the hole. b) Align medium bracket to finisher rib and flater finisher surface before break. Mark the hole. c) Drill (2) 3/16" holes at marked locations. * (OBD Connector) Fig. 6 6) Install the brackets. a) Clean mounting area with alcohol wipe. b) Peel off double-sided tape liner from long and medium brackets. d) Install brackets to lower finisher with holes aligned. e) Install (2) Philips screws and U-nuts from kit. Page 6 of F3 4W010II - Rev
7 11. INSTALLATION PROCEDURE: 7) Install driver side light assembly. a) Clean mounting area with alcohol wipe. b) Peel tabs away from adhesive tape. c) Press assembly onto bracket with tape centered. d) Install (4) 4" cable ties around wire, light assembly and brackets. Trim excess cable tie. 8) Reinstall Instrument lower finisher. a) Reinstall OBD connector to finisher. b) Add 4" cable tie to secure wire loop on light stick to OBD harness as shown. c) Reinstall Instrument lower finisher. 9) Route Passenger side light assembly behind IP brace as shown. Page 7 of F3 4W010II - Rev
8 11. INSTALLATION PROCEDURE: 10) Install Passenger side brackets. (with glove box removed) a) Remove (2) Phillips IP screws. b) Install the (2) short brackets. 11) Mount passenger side light assembly. a) Clean bracket surface with alcohol wipe. b) Peel tabs away from adhesive tape. c) Press light assembly onto brackets with bracket edges aligned to tape edges. d) Install (2) 4" cable ties through bracket holes, around wire, light assembly and brackets. NOTE: ENSURE LEDs ARE NOT OBSCURED BY CABLES TIES, WIRING, BRACKETS etc. Page 8 of F3 4W010II - Rev
9 12. PosiTap installation. b) a) Fig ) Tap vehicle wire. a) Remove cap (slot side) from tap body. b) Slide cap around vehicle wire. c) Tighten the tap TIGHT with finger pressure. NOTE: Do not re-use the tap for subsequent reinstallation. Figures are not to scale. Fig ) Inspect the tap to ensure correct installation. i. Straight and evenly spaced all the way around ii. Tight and minimize gap (wire jacket should be crushed) NOTE: Avoid putting pressure on the vehicle wire and tap for the remainder of the installation. Fig ) Tap accessory wire. e) Insert wire to here a) c) a) Remove tap (non-pierce) side from tap. b) Remove the protective stub from the wire. c) Insert wire through h the non-pierce side opening. d) f) Tighten d) Spread the individual strands into fan shape. e) Insert wire into the tap body and ensure that it is all the way in. f) Tighten the tap TIGHT with finger pressure. Fig ) Confirm the tapped accessory wire. a) Inspect the tap to ensure correct installation. b) Test the signal to ensure that it is working properly. i. Straight and evenly spaced all around ii. Tight and no gap and test the signal Page 9 of F3 4W010II - Rev
10 11. INSTALLATION PROCEDURE: Vehicle Harness b) a) Fig ) Secure the tap. a) b) Secure the tapped wire on the non-pierce side to the body of the tap with electrical tape ( 2 revolutions). Secure the body to harness where vehicle wire is being tapped with electrical tape ( 2 revolutions).... Accessory CAUTION Color(s) given in illustration(s) are for reference only. Use location(s) where color deviates. If a vehicle wire is being used by another accessory and a posi-tap is present, tap the accessory wire NOT the vehicle wire. NOTE: BCM is located behind glove box. Fig. Fig ) Connect Accent Lighting ground. a) Remove bolt from left BCM bracket. b) Install Accent Lighting ground eyelet under screw and reinstall. 18) Tap Accessory Green wire to Light Green wire, Cavity 57 of Black BCM connector M20. See steps for wire tap installation instruictions. Fig 18. Page 10 of F3 4W010II - Rev
11 11. INSTALLATION PROCEDURE: 19) Tap Accessory Brown wire to the Brown wire, Cavity 63 of BCM connector M20. See steps for wire tap installation instructions. 20) Tap Accessory Blue wire to the Dark Blue wire, Cavity 11 of BCM connector M18. See steps for wire tap installation instructions. Page 11 of F3 4W010II - Rev
12 11. INSTALLATION PROCEDURE: 21) Route Power cable. a) Route Power cable and excess wire along existing IP harness as shown. b) Install (2) 4" cable ties as shown. c) Route Power cable behind center IP brace following light stick wire routing. 22) Prepare Module a) Connect Power Cable to Module. b) Connect footwell light wiring to Module. c) Peel tape liner from foam pad and stick pad to Module. 23) Partially install center console and connector encoder and cup holder light sticks. CAUTION Only use your fingers to release Module connector. Prying on release tab with any tool may damage the tab. 24) Mount Module. a) Peel tape liner from foam pad on Module. b) Adhere module to Driver Side IP brace. c) Use (2) 11" cable ties to secure Module to IP brace. d) Use 4" cable tie to secure power and footwell light wiring to IP brace. Page 12 of F3 4W010II - Rev
13 11. INSTALLATION PROCEDURE: 25) a) b) c) d) Connect console accessory wiring. Place console in vehicle so console accessory wiring can reach Module. Route console accessory wires over IP brace. Connect console accessory wiring to module. Use 11" cable tie to secure remaining wiring under console. 26) Verify that the system is functional. 27) Re-assemble vehicle in reverse order. CAUTION Use caution when removing/re-installing trim components to avoid damage, scratches, breaking of clips and/or interior trim panels. Page 13 of F3 4W010II - Rev
14 12) CHECKLIST Prior to completion, verify the following: 1) Connect the battery negative terminal. 2) Turn the vehicle ignition switch to the "ACC" position, push lighting control knob, and confirm the Accent Lighting illuminates. 3) Turn the lighting control knob and confirm that the color changes through 20 variations. 4) Press and hold control knob for 3 seconds and confirm that the Accent Lighting enters "Demo Mode" and cycles through colors. Press knob again to exit demo mode. 5) Leaving the accessory ON, turn the interior Room Lamp to "DOOR" and ignition switch OFF. Open the door and confirm the Accent Lighting Illuminates. 6) Leaving the accessory ON, and the ignition switch OFF, close and lock the door using CDL or Key Fob (if equipped). Confirm that the Accent Lighting turns off. 7) Reset the radio presets to the recorded settings. 8) Place the Accent Lighting Quick Reference card in the glove box. 9) Check the trim for a proper flush fit after re-installing the interior components. 10) Clean the interior of the vehicle. 11) Inspect the vehicle interior and exterior for damage. Page 14 of F3 7W010II - Rev
15 Mechanization of this Accent lighting kit Pink HMI L i g h t L i g h t Red Orange S t i c k Dark Blue Blue Brown Controller Sky Blue Green Black Open Brown Light Green Red Page 15 of F3 4W010II - Rev
16 10mm 1 inch Page 16 of F3 4W010II - Rev
17 Kit Contents: Nissan Universal Accent Lighting Kit - 999F3 AW000 Parts Contained in Bag Labelled 'Installation Kit'. Qty Part Number 1 Cable tie 15" - Black 4 2 Cable tie 11" - Black 2 3 Cable tie 4" - Black 13 4 Grey foam rectangle 80mm x 30mm x 5mm - Adhesive one side 6 5 Small bracket 28mm long 2 6 Medium bracket 54mm long 1 7 Large bracket 80mm long 1 8 Posi-tap connector - Red / Grey 3 999M1 VT000 9 Control knob (Black + white printing) 1 999F3 AW Alcohol preparation wipe 4 11 U' Nut 2 12 Module adhesive fixing 53mm x 74mm 1 13 Lens Retaining Ring 9mm OD - Black 2 14 Clear plastic lens - 7.5mm diameter 2 15 Pozi-drive self-tap screw 1/2" long - Black 2 16 Encoder lock nut 1 17 Quick reference guide 1 999F3 AW Double-sided adhesive fixing 12mm x 20mm (All on one backing paper) 4 19 Double-sided adhesive fixing 12mm x 102mm (All on one backing paper) 4 20 Parts list / Replacement template 1 999V2 AW Vehicle interface harness 1 999F3 AW005 Parts Not In 'Installation Kit' bag. 22 Encoder and harness assembly 1 999F3 AW Cup-holder lights and harness assembly 1 999F3 AW Foot-well lights and harness assembly 1 999F3 AW Control module (within polythene zip bag) 1 999F3 AW of F3 6X000II - Rev
GENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION: Illuminated Kick Plate APPLICATION: Rogue (2011) PART NUMBER: 999G6 GX010 KIT CONTENTS: Item A B C G H QTY 1 1 1 D 1 E 1 F 3 15 6 Description Kick Plate,
More informationTOYOTA Tundra 2007 - BACK-UP CAMERA SYSTEM Preparation
Preparation Part Number(s): PT233-34070, PT923-35070-11, PT923-35070-43 NOTE: Part number of this accessory may not be the same as part number shown. Back Up Monitor Kit Contents PT923-35070-11 / PT923-35070-43
More informationINSTALLATION INSTRUCTIONS
Rear Vision System Tailgate Handle Camera Mirror Display 2004-2014 Ford F-150 and 2008-2015 Ford Super Duty (Kit part numbers 9002-9521) Kit Contents: Mirror Tailgate Handle with camera and harness Interior
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII23628 2003 PILOT Issue Date MAY 2002 PARTS LIST Security System Kit (sold separately): P/N 08E51-S84-100 2 Remote controls Attachment
More informationTOYOTA TACOMA 2008- HANDS FREE BLU LOGIC Preparation
TOYOTA TACOMA 2008- HANDS FREE BLU LOGIC Preparation Part #: PT923-00112 Conflicts: JBL Audio, Factory Navigation NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents:
More informationTOYOTA PRIUS 2010- HANDS FREE BLU LOGIC Preparation
TOYOTA PRIUS 2010- HANDS FREE BLU LOGIC Preparation Part #: PT923-00111 Conflicts: JBL Audio, Factory Navigation NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents:
More informationKEYLESS ENTRY UPGRADE SECURITY SYSTEM for 2004 TOYOTA HIGHLANDER
KEYLESS ENTRY UPGRADE SECURITY SYSTEM for 2004 TOYOTA HIGHLANDER DEALER SERVICE AND INSTALLATION MANUAL KIT NO. 00016-30915 Contents PARTS LIST... 2 PARTS ILLUSTRATIONS... 2 VEHICLE PREPARATION... 3 INSTALLING
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. DESCRIPTION: Auto-Dimming Mirror Kit with Compass and HomeLink 2. APPLICATION: Titan 3. PART NUMBER: 999L1 WS000 4. KIT CONTENTS: Item Qty Description Service
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. ACCORD All 30209 2-AND 4-DOOR SYSTEM (VP, LX, SE) Issue Date AUG 2005 PARTS LIST Security System Attachment: P/N 08E55-SDA-100A Unit panel
More informationTime needed: ~3h for lid replacement only. Add 1h for operation harness in lid and ~2h more for installing drive unit and cable harness in trunk.
DIY for replacing trunk lid and/or retrofitting electrical operation of trunk lid. This document is meant to be a support and give advice on the procedure but I will take no responsibility for any damage
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 26327 2004 S2000 Issue Date OCT 2004 PARTS LIST Security System: P/N 08E51-S84-100 Attachment Kit: P/N 08E55-S2A-101 2 Remote controls
More informationPOWER LOCK KIT GENERAL INSTALLATION -J04427 REV. 2007-12-04. Kit Number. Models. Additional Parts Required. Kit Contents
-J0 REV. 00--0 POWER LOCK KIT GENERAL Kit Number -0, 0-0 Models For model fitment information, please see the P&A Retail Catalog or the Parts and Accessories section of www.harleydavidson.com (English
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. XM RADIO SYSTEM 2003 ACCORD 4 DOOR AII 24378 Issue Date MARCH 2003 The XM Radio will not fit in a vehicle equipped with a rear entertainment
More information2003/2004/2005 TOYOTA COROLLA
2003/2004/2005 TOYOTA COROLLA KEYLESS ENTRY UPGRADE SECURITY SYSTEM INSTALLATION INSTRUCTIONS KIT NO. 00016-30120 SPECIAL NOTE: Installation Sequences After TMS and Safety mandated preparatory steps have
More informationInstalling RNS-E SAT NAV for Audi A4
As one of the major options on the A4 you can get a DVD Satellite Navigation System call the RNS-E. With the help of ebay these sat nav systems are now available to by at a rough cost of 650 plus the cost
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. All 24393 ACCORD (DX, LX) SYSTEM 2-AND 4-DOOR Issue Date AUG 2002 PARTS LIST Security System Attachment (LX): P/N 08E55-SDA-100A Unit panel
More informationINSTALLATION INSTRUCTIONS
Rear Vision System Aftermarket and Factory 5.0, 8.4 and 6.1 MyGig Touch Screen Display (Factory Display requires Chrysler/Dodge dealer to activate) 2009 Current* Dodge Ram (Kit part number 1009-6503) *NOTE:
More informationCONTENTS TOOLS REQUIRED: Ratchet 13mm Socket 10mm Socket Phillips Screwdriver Pliers Panel Removal Tool. Amp Installation
CONTENTS 1EA. SUBWOOFER ASSEMBLY P/N RUWRANGLER 1EA. 200 WATT AMP/BRACKET ASSEMBLY P/N RM11JKBTL - Bracket P/N RE08BTL200R - Amp 1EA. POWER HARNESS P/N RHWRANGLERPWR 1EA. OVERLAY HARNESS P/N RHWRANGLER
More informationP150SC15. Designed for 2015 Ford F150 Super-Cab and Super-Crew vehicles without Sony System. 2015 Stillwater Designs P150SC15-A2-20150813
P150SC15 Designed for 2015 Ford F150 Super-Cab and Super-Crew vehicles without Sony System Subwoofer Assembly Amplifier Assembly Amplifier Harness 2015 Stillwater Designs P150SC15-A2-20150813 M6 Bolt M6
More informationPart Name/Description Part Number Quantity. Power Cable 4000950-5 1
Note: Indented items indicate parts included in an assembly listed above Part Name/Description Part Number Quantity Power Cable 4000950-5 1 Raven Harness Adapter Kit 4100525 1 Installation Instructions
More informationVolkswagen Jetta, Golf, GTI 1999, 2000 Brake System 46 Brakes - Mechanical Components (Page GR-46)
46 Brakes - Mechanical Components (Page GR-46) Front brakes Brake pads, removing and installing Brake pads, removing and installing FN 3 brake caliper, servicing FS III brake caliper, servicing Rear wheel
More informationPost Mount Light Installation*
Post Mount Light Installation* *For the general installation of most Post Mount Spotlights, many vehicles may need slight modifications to these instructions. You will need the following tools: High torque
More informationRetrofit Instructions Installing a Sport Heated Steering Wheel - Leather, Multifunction BMW X5, E53, 2001 2006
Retrofit Instructions Installing a Sport Heated Steering Wheel - Leather, Multifunction BMW X5, E53, 2001 2006 Disclaimer: This set of instructions is simply a guide on how I installed my own heated steering
More informationWARNING! REQUIRED TOOLS & SUPPLIES: HIGH VOLTAGE
INSTRUCTIONS Product: GEM Electric Motorcars Models: All Subject: Instructions for installing Stereo Accessory Estimated Completion Time:.75 Hours Parts: See Page # 7 REQUIRED TOOLS & SUPPLIES: (1) 3/8
More informationR02GA. July 31, 2002. Dear Blue Bird Owner:
R02GA July 31, 2002 Dear Blue Bird Owner: This notice is sent to you in accordance with the requirements of the National Traffic and Motor Vehicle Safety Act. Blue Bird Body Company has determined that
More informationCUSTOM AUXILIARY FORWARD LIGHTING KIT
-J0 REV. 0--0 CUSTOM AUXILIARY FORWARD LIGHTING KIT GENERAL Kit Number -0, 0000 Models This Custom Auxiliary Lighting Kit adds lamps and turn signals to 00 and later FLHX model motorcycles. Additional
More information5 Mechanisms and accessories
5 Mechanisms and accessories 51A SIDE OPENING ELEMENT MECHANISMS 52A NON-SIDE OPENING ELEMENT MECHANISMS 54A WINDOWS 55A EXTERIOR PROTECTION 56A EXTERIOR EQUIPMENT 57A INTERIOR EQUIPMENT X79 NOVEMBER 2009
More informationPARTS & INSTALLATION INSTRUCTIONS MEYER SNOW PLOW LIGHTS
Form 1-696 R1 January, 2003 PARTS & INSTALLATION INSTRUCTIONS MEYER SNOW PLOW LIGHTS PARTS LIST ITEM PART NO. QTY. DESCRIPTION 07033 1 SNOW PLOW LIGHT CARTON 1 07034 1 Snow Plow Light, Pass. Side (No Hardware)
More informationInstallation Instructions
Installation Instructions Page 1 of 16 January 2008 Equipment Parts, Trailer Hitch Ver 3.0 Accessory Development SUBJECT TRAILER HITCH KIT (US Only) - P/N 71 60 0 413 359 MODEL X5 (E70): Select Vehicle
More informationINSTALL/REMOVAL INSTRUCTIONS: WINDOW LIFT MOTOR
REMOVAL/INSTALL OF WINDOW LIFT MOTOR (742-273) Ford Expedition 1997 2002, Lincoln Navigator 1998 2002, Ford F-150 Super Crew Cab 2001 General Tech Tips: Use painter s tape rather than duct tape to secure
More informationTOOL SVC NUMBERS: 250-2598, 250-2600 SVC CONTENTS ITEM QTY DESCRIPTION PART NUMBER 1 1 CUTTING TOOL 250-2598 2 1 EXTRACTION TOOL/PART# 250-2600
07-08 TOYOTA FJ CRUISER, 05-09 SIENNA, 06-08 SCION TC PART NUMBER: 250-1732 1 CRUISE CONTROL KIT TOOL SVC NUMBERS: 250-2598, 250-2600 2 2 1 BASE KIT CONTENTS ITEM QTY DESCRIPTION 1 1 CONTROL SWITCH ASSEMBLY
More informationRECOMMENDED TOOLS PERSONAL & VEHICLE PROTECTION SAFETY GLASSES
PART NUMBER: 250-9612 GENERAL APPLICABILITY THIS CRUISE WAS TESTED AND VERIFIED ON: FORD FOCUS SE & S MODELS (AT/MT) FORD TRANSIT ALL MODELS RECOMMENDED TOOLS PERSONAL & VEHICLE PROTECTION SAFETY GLASSES
More informationBefore installation it is important to know what parts you have and what the capabilities of these parts are.
INSTALLATION GUIDE Before installation it is important to know what parts you have and what the capabilities of these parts are. The Recon XZT is the smallest and most powerful gauge of its kind. With
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory TRIM Application 2008 ACCORD 4-DOOR Publications No. AII 35362 Issue Date AUG 2007 PARTS LIST Steering Wheel Trim (Without Navigation) P/N 08Z13-TA0-100 Right steering
More informationTOYOTA TUNDRA 2015 Billet Grille w/led DRL
TOYOTA TUNDRA 2015 Billet Grille w/led DRL Part Number: 00016-34088 Accessory Code: BG3000 Conflicts Models 1794 and Platinum Kit Contents Item # Quantity Reqd. Description 1 2 LED DRL 2 1 Driver Box 3
More informationMazda CX7 2007-09 99-7508
INSTALLATION INSTRUCTIONS FOR PART 99-7508 APPLICATIONS Mazda CX7 2007-09 99-7508 KIT FEATURES DIN Radio Provision with Pocket ISO Mount Radio Provision with Pocket Double DIN Mount Radio Provision Stacked
More informationUNIVERSAL LUMBAR INSTALLATION INSTRUCTIONS
UNIVERSAL LUMBAR INSTALLATION INSTRUCTIONS CONTENTS Parts List... 2 Parts Diagram... 2 Helpful Hints... 3 Installation... 4 Operation and Troubleshooting Guide... 6 Warranty Information... 8 Form #3132,
More informationFL ADJUSTABLE RIDER BACKREST MOUNTING HARDWARE KIT
-J070 REV. 0-0-0 FL ADJUSTABLE RIDER BACKREST MOUNTING HARDWARE KIT GENERAL Kit Number 9-09A Models For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com
More informationINSTALLATION MANUAL. Installation Instructions
INSTALLATION MANUAL Power-Pole Signature Series Shallow Water Anchor Installation Instructions CAUTION: Read this instruction manual carefully. Become familiar with the controls and know how to operate
More informationEXTENDED-WIRE HANDLEBAR SWITCH KITS
-J03396 REV. 2010-02-11 EXTENDED-WIRE HANDLEBAR SWITCH KITS ENERAL Kit Numbers 70246-10, 70318-10 Models Neither of these kits is compatible with cruise control-equipped 2007 or earlier models. Kit 70246-10
More informationKEYPAD LOCK RETROFIT KIT
KEYPAD LOCK RETROFIT KIT INSTRUCTIONS FOR ASSEMBLY IMPORTANT READ & SAVE THESE INSTRUCTIONS Tools Required for Assembly 5/32 hex (Allen) wrench #2 Phillips screwdriver Isopropyl alcohol or alcohol wipes
More informationPRODUCT: WASHER / WASHER-DRYER COMBO MODEL: AW 120 / AW 122 / AW 125 AWD 120 / AWD 121 / AWD 129
PRODUCT: WASHER / WASHER-DRYER COMBO MODEL: The information included in this Splendide Repair Manual may change without notice. Please see our web site www.splendide.com/service/docs.html for updates,
More informationTrailblazer, Envoy, Rainier, Ascender
6. After removing the trim plate bezel simply remove the four ¼ screws holding the instrument cluster in place. Pull the cluster out and unplug the single wiring harness connection in the back. Trailblazer,
More informationtidesmarine Smart Seal Temperature Alarm System Generation II Installation Instructions Starboard side cable
tidesmarine Smart Seal Temperature Alarm System Generation II Installation Instructions Starboard side cable Port side cable (with black cable tie attached) Power cable Preparing for Installation 1 Overall
More informationParts and Accessories Installation Instructions
Parts and Accessories Installation Instructions INFO 1 4 2 5 3 6 TONE SELET FM AM MODE MENU F 38 393 B Retrofit Kit On-board Monitor and Navigation System BMW 7 Series (E 38) These installation instructions
More informationBack-Up Camera Installation Guide
Hz Hz In This Guide: Back-up camera installation requires connecting power wiring to the existing reverse lighting circuit and adding a chassis ground, as well as routing a video signal cable to the front
More informationR O A D M A S T E R, I N C.
R O A D M A S T E R, I N C. 11 10 20 12 4 18 19 1 2 13 16 ITEM QTY NAME MATERIAL 1...2... 1/2" x 3 1/2" BOLT... 350103-00 2...2... 1/2" x 2" BOLT... 350097-00 3...6... 1/2" x 1 1/2" BOLT... 350095-00 4...2...
More informationTraditional Sonar and DSI Sonar Installation
Traditional Sonar and DSI Sonar Installation This document covers the installation of the transducer and display unit installation, which includes connecting the unit to power and installing the unit on
More informationELECTRONICS G H I J K L M
ELECTRONICS TM LASER INSTALLATION INSTRUCTIONS PARTS KIT Parts Kit includes the following: A- (1) Universal Mounting Bracket A B- (1) Red L.E.D. Laser Alert Light C- (1) Piezo Beeper w/ O Ring Tape D-
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application 2009 PILOT Publications No. AII 39408 Issue Date MAY 2008 PARTS LIST Steering Wheel Trim (With Cruise and Audio) P/N 08Z13-SZA-130B (Chocolate) P/N 08Z13-SZA-140B
More informationRECOMMENDED TOOLS PERSONAL & VEHICLE PROTECTION SAFETY GLASSES
HYUNDAI ACCENT 2010- /ELANTRA 2012- / KIA RIO 2012- PART NUMBER: 250-9628 GENERAL APPLICABILITY THIS CRUISE WAS TESTED AND VERIFIED ON: (AT/MT) VEHICLES RECOMMENDED TOOLS PERSONAL & VEHICLE PROTECTION
More informationWritten By: Walter Galan
Installing iphone 4S Display Assembly Written By: Walter Galan TOOLS: Phillips 00 Screwdriver (1) Plastic Opening Tools (1) PARTS: iphone 4S Display Assembly (1) iphone 4 and 4S Screen Protector (1) Small
More informationFG MOISTURE MONITOR Installation & Operation Manual
FG MOISTURE MONITOR Installation & Operation Manual Issue 3.0 7/20/10 1 Contents SERVICE AND TECHNICAL SUPPORT... 2 INSTALLATION:... 3 MOISTURE SENSOR INSTALLATION:... 3 SENSOR CONNECTOR:... 5 MONITOR
More informationBODY-12, Door Handle - Removal, Installation, and Adjustment
Introduction BODY-12, Door Handle - Removal, Installation, and Adjustment There are many different procedures floating around describing how to replace the door handles on a 944 and every one of them will
More informationInstallation instructions, accessories - Handsfree for cellular phone, system B, entry level
XC90 Section Group Weight(Kg/Pounds) Year Month 3 39 0.5/1.1 2006 07 XC90 2003, XC90 2004 IMG-249663 Page 1 of 18 Required tools A0000162 A0000163 IMG-239664 M0000232 IMG-253123 IMG-252223 Page 2 of 18
More informationMazda CX9 2007-up 99-7516B
INSTALLATION INSTRUCTIONS FOR PART 99-7516B APPLICATIONS Mazda CX9 2007-up 99-7516B KIT FEATURES DIN radio provision with pocket ISO radio provision with pocket Double DIN radio provision Stacked ISO units
More informationA&A CORVETTE PERFORMANCE C6 BOOST & FUEL GAUGE INSTALLATION INSTRUCTIONS
A&A CORVETTE PERFORMANCE C6 BOOST & FUEL GAUGE INSTALLATION INSTRUCTIONS 1. Check your gauges before you take them out of the packaging to make sure they are at 0 (zero) psi for both boost and fuel pressure.
More informationNetworkfleet 3500 Product Line Installation Guide
Networkfleet 3500 Product Line Installation Guide Light/Medium Duty (L3500) Heavy Duty (H3500) Universal (U3500) www.networkcar.com/fleet Customer Care: (866) 227-7323 customercare@networkcar.com Table
More informationMazda CX7 2010-up 99-7520B
INSTALLATION INSTRUCTIONS FOR PART 99-7520B APPLICATIONS Mazda CX7 2010-up 99-7520B KIT FEATURES DIN radio provision with pocket ISO radio provision with pocket Double DIN radio provision Painted matte
More informationPart Number: 250-1859
General Applicability 2010 Honda Insight 07- Kia Optima / Forte / Rondo/ 10- Sedona / 12 Soul 10- Hyundai Tucson / Elantra Touring ETC 2012 Accent / Elantra/ Genesis Recommended Tools Safety Tools Gloves,
More informationBACKUP CAMERA JEEP COMMANDER/GRAND CHEROKEE
BACKUP CAMERA 1 JEEP COMMANDER/GRAND CHEROKEE 2 Call Out Description Parts Quantity 1 Tie Wrap-Nylon 6.9" Supplied in kit 12 2 Camera, Rear View Supplied in kit 1 3 Camera Extension Harness Connector Supplied
More informationInstallation Instructions: Electrical System for Towing Hitch... 3
... 3 Installation Instructions: Electrical System for Towing Hitch... 3 321 527 391 103-002 - 51/12 VW Polo A05 RHD Westfalia 321 525 300 143 VW Polo V RHD, 06/09-321 527 300 143 VW Polo V RHD, 06/09-4
More informationINSTALL/REMOVAL INSTRUCTIONS: WINDOW REGULATOR
REMOVAL/INSTALL OF WINDOW REGULATOR (748-547) Chrysler 300 2005 10, Dodge Magnum 2005 08, Dodge Charger 2006 09 General Tech Tips: Use painter s tape rather than duct tape to secure window. It will not
More informationInstallation instructions, accessories. Cruise control. Volvo Car Corporation Gothenburg, Sweden. Instruction No Version Part. No. 30739998 1.
Instruction No Version Part. No. 30739998 1.1 Cruise control Page 1 / 11 Equipment A0000162 A0000161 A0801178 D8802049 Page 2 / 11 M8802108 Page 3 / 11 IMG-223164 Page 4 / 11 IMG-213320 Page 5 / 11 INTRODUCTION
More informationINSTALLATION GUIDE. APPLICATION LENGTH MODEL YR PART # Bestop PART #
INSTALLATION GUIDE APPLICATION LENGTH MODEL YR PART # Bestop PART # Ford Super Duty F-250 / F-350 Regular Cab (48 ) 1999 2007 10-02513-24 75102-01 Ford Super Duty F-250 / F-350 Super Cab (60 ) 1999 2007
More informationFRONT BUMPER INSTALLATION INSTRUCTIONS 2007-2011 DODGE / MERCEDES SPRINTER
Aluminess Products Inc 9402 Wheatlands Ct. #A Santee, CA 92071 619-449-9930 FRONT BUMPER INSTALLATION INSTRUCTIONS 2007-2011 DODGE / MERCEDES SPRINTER Please read before beginning Stainless steel hardware
More information4RU High Density Shelf Installation Instructions
4RU High Density Shelf Installation Instructions Table of Contents General Product Information... 1.0 Safety Precautions... 2.0 Tools Required... 3.0 Package Contents... 4.0 Installing the Product Unpacking...
More information1978-83 Malibu 1978-87 Monte Carlo 1978-87 El Camino
Important facts about this kit. 1. The dash panel used in this picture is used by permission of Covan's Classic. 2. This kit requires some modification to your original under dash wiring harness. It is
More informationInstallation Instructions Avalanche XUV Cap IMPORTANT! IMPORTANT!
Installation Instructions Avalanche XUV Cap IMPORTANT! Read all instructions carefully before commencing any work. Always wear safety equipment. Some installation steps will require two or more installers.
More informationChevy Equinox 2010-2015 / GMC Terrain 2010-2014 (with monochrome display) 99-3307G
INSTALLATION INSTRUCTIONS FOR PART 99-3307G Chevy Equinox 2010-2015 / GMC Terrain 2010-2014 (with monochrome display) 99-3307G KIT FEATURES ISO DIN radio provision with pocket ISO DDIN radio provision
More informationAM/FM ANTENNA RELOCATION KIT
-J0 REV. 008-09-0 AM/FM ANTENNA RELOCATION KIT GENERAL Kit Number 766-09 Models This kit is used to relocate a fender-mounted AM/FM antenna to a Detachable Tour-Pak on specific model motorcycles. For model
More informationADDING AN ELECTRIC AUXILIARY FAN TO RADIATOR STACK ON 03 ALPINE COACH
ADDING AN ELECTRIC AUXILIARY FAN TO RADIATOR STACK ON 03 ALPINE COACH The original design of the 03 Alpine Coaches (and perhaps other years as well) did not include any kind of engine fan engage mechanism
More information4.3-inch Back-Up Camera
TM 4.-inch Back-Up Camera Model No.: PKC0BU4 Owner s Manual and Warranty Information Read these instructions completely before using this product. Retain this Owner s Manual for future reference. INTRODUCTION
More informationGPS AutoSteer System Installation Manual
GPS AutoSteer System Installation Manual Supported Vehicles John Deere Sprayers 4720 4630 4730 4830 AutoTrac Ready PN: 602-0227-01-A LEGAL DISCLAIMER Note: Read and follow ALL instructions in this manual
More informationUB1 AIR CONDITIONING UNIT INSTALLATION INSTRUCTIONS
UB1 AIR CONDITIONING UNIT INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS: Carefully read these instructions before installing your new air-conditioner. AUSTRALIAN AUTOMOTIVE AIR AL00500054E 1 Table
More informationService Guide. Gateway M275
Service Guide Gateway M275 Contents Replacing Gateway M275 Components.................................... 1 Identifying the convertible tablet PC model...................................... 2 Identifying
More informationILISC515-A Shift Interlock (Manual Lift Door) 2015 Ford Transit, 3.7L and 3.5L
An ISO 9001:2008 Registered Company ILISC515-A Shift Interlock (Manual Lift Door) 2015 Ford Transit, 3.7L and 3.5L Introduction The ILISC515-A is a microprocessor driven system for controlling wheelchair
More informationVOYAGER 570G. 744A Sprayer Control
VOYAGER 570G 744A Sprayer Control U S E R M A N U A L U S E R M A N U A L Table of Contents CHAPTER 1 - INTRODUCTION...1 SYSTEM CONFIGURATIONS...1 KIT CONTENTS...3 CONTROL HOUSING ASSEMBLY...5 CHAPTER
More informationInstallation Instructions 4508 4508S
SYMPHONY Spread Lavatory Faucet with Speed Connect Drain Congratulations on purchasing your American Standard faucet with Speed Connect drain, a feature found only on American Standard faucets. Speed Connect
More informationTERMINATION EQUIPMENT INSTRUCTION MANUAL TELE-PIERCE P/N 356-246
TERMINATION EQUIPMENT INSTRUCTION MANUAL TELE-PIERCE P/N 356-246 OPERATION AND SERVICE INSTRUCTIONS AMPHENOL 157 SERIES TELE-PIERCE MULTI-WIRE TERMINATION TOOL 356-246 AMPHENOL TERMINATION SYSTEMS 1830
More informationInstallation instructions, accessories - Navigation system, RTI
XC90 Section Group Weight(Kg/Pounds) Year Month 3 393 4/8.8 2007 08 Page 1 of 20 Required tools A0000162 IMG-239667 IMG-239664 IMG-239980 IMG-242205 R8802817 R3905015 Page 2 of 20 R3903812 IMG-213320 Page
More informationSCION FR-S 2013 - PERFORMANCE AIR INTAKE Preparation 2.0L F-4
Preparation 2.0L F-4 Part Number: PTR03-18130 Please see Page 12 for important Care and Maintenance information! Kit Contents Item # Qty. Service Part # Description 1 1 PTR03-18130-AC TRD Air Box Base
More informationhttp://mbworld.org/forums/c32-amg-c55-amg-w203/449471-famous-ac-clicking-noiseac-footwell-damper-linkage-replacement-diy-details-steps.
Air Conditioner / HVAC W203 Stepper Motor Repair PART 2 OF 3 forums/c-class-w203/177068-noisy-air-conditioner-stepper-motorreplacement-clicking-hissing.html forums/c32-amg-c55-amg-w203/449471-famous-ac-clicking-noiseac-footwell-damper-linkage-replacement-diy-details-steps.html
More information1969 DODGE CORONET Two panel Sequential LED Taillight kit installation guide
1969 DODGE CORONET Two panel Sequential LED Taillight kit installation guide Kit Contents: 2 LED panels 4 rubber grommets 1 power wire with t-tap 1 driver side LED harness, 24 1 passenger side LED harness,
More informationRemote Access System Installation
2011-2013 Explorer Remote Access Remote Access System Installation CONTENTS VEHICLE PREPARATION Hood Switch Wire Harness Installation Hood Switch Installation RMST Module Installation RMU Module Installation
More informationUse subject to terms and conditions posted at http://www.burgertuning.com/terms.htm
Use subject to terms and conditions posted at http://www.burgertuning.com/terms.htm THIS PART IS LEGAL FOR USE ONLY IN COMPETITION RACING VEHICLES AS DEFINED UNDER CALIFORNIA LAW, AND IS NOT LEGAL FOR
More informationMulti Function, User Configurable Remote Vehicle Security System with 4 Button Replaceable Membrane Remote Transmitter
MODEL PRO-9744 INSTALLATION MANUAL Multi Function, User Configurable Remote Vehicle Security System with 4 Button Replaceable Membrane Remote Transmitter This System Allows The Transmitter Buttons To Be
More informationTriple Threat 3-in-1 Game Table 3 IN 1 GAME TABLE
NG0M Triple Threat 3-in- Game Table 3 IN GAME TABLE Thank 3 in Y Game Table Thank you for your purchase of our product. We work around the clock and around the globe to ensure that our products maintain
More informationAM/FM ANTENNA KIT (TOUR-PAK MOUNT)
-J077 REV. 008-0-0 AM/FM ANTENNA KIT (TOUR-PAK MOUNT) GENERAL Kit Number 7-98A Models For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com
More informationTable of Contents. www.hunterfan.com. What to Expect with. Preparation. Tools Needed. Wiring. Hanging the Fan. Blades. Motor Housing.
www.hunterfan.com Table of Contents What to Expect with Your Installation 30 inches Hanging the Fan Wiring 8 Maintenance, Operation & Cleaning Light Kit 13??? 14 1 9 Troubleshooting 11 5 Blades Motor Housing
More informationINSTALL/REMOVAL INSTRUCTIONS: WINDOW REGULATOR
REMOVAL/INSTALL OF WINDOW REGULATOR (741-306) Honda Accord 2003 07 General Tech Tips: Use painter s tape rather than duct tape to secure window. It will not damage paint or leave sticky residue. A plastic
More informationStep 1. Item 6. Item 1
Voltage Regulators QD3/T350 Motor Replacement Kit Kit Number 57A63675100B Service Information S225-50-35 Contents General..................................... 1 Parts Supplied...............................
More informationBulb Replacement REPLACING BULBS WARNING
Bulb Replacement REPLACING BULBS Check the operation of all exterior lamps before you drive the vehicle. Caution: Before attempting to replace a bulb, ensure that both the affected lamp and the vehicle's
More informationParts and Accessories Installation Instructions
Parts and Accessories Installation Instructions R5 5 Z CD changer retrofit kit MINI (R 5 and R 53) LHD and RHD The installation time is approx..5 hours, but this may vary depending on the condition of
More information2002 2005 Mini Cooper S Grille Install Instructions
2002 2005 Mini Cooper S Grille Install Instructions Lower Front Grille BEFORE AFTER Package Contents 1 perforated grille (Stiletto, RAZR, or Monster) 6 Zip Tie Mounting Pads 1 is for the temp. sensor 5
More informationBBWX1 Satellite Weather Receiver. Installation and Maintenance Guide
BBWX1 Satellite Weather Receiver Installation and Maintenance Guide Rev FUSA 15JUL2007 Table of Contents Safety Precautions 3 Disclaimer. 3 Contents of Package. 4 Tools Required..4 Installation General
More informationEasyNote TJ Series. Disassembly Manual
EasyNote TJ Series Disassembly Manual CHAPTER3 Replacing notebook components Preventing static electricity discharge Preparing the work space Required tools Preparing the notebook Adding or replacing memory
More informationELECTRONIC THERMOSTAT AND THERMOMETER With SPEED CONTROL
148 OLD CONCORD TURNPIKE, BARRINGTON NH 03825 USA TEL (603) 868-5720 FAX (603) 868-1040 1-800-435-6708 E-Mail:sales@seafrost.com www.seafrost.com ELECTRONIC THERMOSTAT AND THERMOMETER With SPEED CONTROL
More informationWiper Motor Marinco 2.5. Installation Instructions
Wiper Motor Marinco 2.5 Installation Instructions Wiper Motor Marinco-2.5 The Marinco 2.5 Wiper Motor Offers the Following Features: Fully sealed base and housing which allows installation in outdoor wet
More information