User s Manual SC-VCP Series Video Transmitter & Receiver with Power Supply Unit

Transcription

1 User s Manual SC-VCP Series Video Transmitter & Receiver with Power Supply Unit SC-VTP0601/1501/2501 SC-VRP0601/4/8 SC-VRP0604H/1504

2 Precaution & Safety Guidelines Please read carefully the user s manual and check the specification of each devices prior to installation. Please turn OFF the power of the units prior to installation. Do not drop the device or subject it to vibration. It may cause any malfunction of the device. Avoid installing nearby strong magnetic materials or radio frequency such as wireless electronic equipments as radio or TV. Do not use the device when any smoke or smell is produced from the unit. It may be subject to fire or electric shock. If any smoke or smell is produced, please turn off the unit and remove the power cable immediately, and contact your distributor for repair. If the power is not ON, please check whether the power cable is connected correctly or not. Please use only our approved power supply unit (power adapter) 48VDC/1A provided together with the package. Do not connect any other cable besides the coaxial cable. When the cable is not connected correctly, the unit may not work properly and/or it may produce a short circuit, and also it may influence to the entire CCTV connection system. Therefore, please turn on the power only after the cables are connected correctly. If any short circuit is produced or the cable is connected inappropriately, check the cable connection and solve the short circuit before turning on the unit again. If the video is not displayed when the power is on, please check if the video input and/or output port are connected correctly. For 4 ch and 8 ch video transmission solutions, be sure of connecting the VIDEO OUT harness to the DVR, and connecting the BNC connector (SIGNAL IN) with the coaxial cable. Please turn on the power only if the transmitter and the receiver are connected properly. If the device is not working properly, please contact your distributor.

3 How to connect the coaxial cable When you want to extend the cable, connect the cable as below - BNC connector connection: BNC-M - BNC-JJ - BNC-M - F connector connection: F connector - F connector extender F connector When you want to terminate the cable, please connect a 75Ω BNC-F connector or a F connector at the terminal of coaxial cable connected with the receiver as below. Avoid connecting an RCA cable to terminate the cable. Good Bad Connecting a 75Ω BNC-F connector at the terminal of coaxial cable Connecting of coaxial cable and RCA cable by tapping

4 1. INTRODUCTION 1-1. OVERVIEW Using our video and power transmission solutions over the single coaxial cable, it is possible to transmit high quality video signals for fairly long distance by modulating the original signals to the signals with has powerful interference immunity, and also it is possible to supply power to the camera through the same coaxial cable simultaneously. As it is unnecessary to do power wiring work, you can reduce the term of work and material cost FEATURES Various models provided depending on the installation condition Per Channels: 1CH/ 4CH/ 8CH Per Power consumption of the camera: 6W, 15W, 25W Long distance video transmission and supply power to camera over the single coaxial cable Excellent interference immunity Small size, providing harness cable for easy installation Keeping the video signals against the interception (Impossible to intercept and monitoring the video without the receiver) Auto diagnostics for cable and auto restoration for power supply (Patent No : Video and power transmission system with stable power supply) Auto video distance adjustment Surge protection function

5 2. COMPONENTS 2-1. COMPONENTS PER MODEL MODEL TX. RX. BRACKET VCP0601 POWER CORD, ADAPTER MANUAL VCP0604/H /8 VCP1501 VCP1504 VCP2501 Model no: The letter C of SC-VCPXXXX commonly indicates a set of transmitter and receiver BASIC SPECIFICATION PER MODEL MODEL CH. MAX.DISTANCE (RG-6) POWER SUPPLY COMPONENTS SC-VCP Km 6W(DC 12V 0.5A) VTP VRP0601 SC-VCP Km 6W(DC 12V 0.5A) VTP VRP0604 SC-VCP0604H 4 1Km 6W(DC 12V 0.5A) VTP VRP0604H SC-VCP Km 6W(DC 12V 0.5A) VTP VRP0608 SC-VCP POWER: 600m VIDEO: 1Km 15W(DC 12V 1.3A) VTP VRP1501 SC-VCP POWER: 600m VIDEO: 1Km 15W(DC 12V 1.3A) VTP VRP1504 SC-VCP POWER: 300m 30W(DC 12V 2.5A) VTP VRP0601

6 3. PRODUCT PARTS AND PERIPHERAL DEVICE CONNECTION 3-1. PRODUCT PARTS AND FUNCTION SC-VTP0601/ SC-VTP VIDEO IN: Connect the video signal of the camera 2 POWER OUT: 12VDC power out for camera operation 3 RF OUT: Connect the receiver via the coaxial cable SC-VTP2501 VIDEO IN (CAMERA CONNECTION PORT) POWER OUT PORT (12VDC / 2.5A) RF-OUT (COAXIAL CABLE CONNECTION PORT)

7 SC-VRP RF IN: Video Input port. Connect the transmitter via the coaxial cable 2 POWER IN: Connect the 48VDC power adapter 3 VIDEO OUT: Video output port 4 LED Indicator: It indicates the connection status of the transmitter LED INDICATOR ON Flickering Description Normal connection Disconnection or Short circuit of the cable SC-VRP0604/

8 1 RF IN: Video Input port. Connect the transmitter via the coaxial cable 2 VIDEO OUT: Video output port 3 LED INDICATOR: It indicates the connection status LED INDICATOR GREEN RED Description Normal connection Disconnection or Short circuit of the cable SC-VRP RF IN: Video Input port. Connect the transmitter via the coaxial cable 2 VIDEO OUT: Video output port 3 LED INDICATOR: It indicates the connection status LED INDICATOR GREEN RED Description Normal connection Disconnection or Short circuit of the cable 3-2. INSTALLATION HOW TO CONNECT When installing to new cameras: 1 Connect the transmitter to the camera(sc-vtpxxxx) 2 Connect the coaxial cable to the transmitter 3 Connect the coaxial cable to the BNC connector of the receiver 4 Connect the video out port of the receiver to the DVR or Monitor 5 Turn the receiver s power on Please turn on the power of the receiver (SC-VTPXXXX) only after the connection of all the equipments is done. When installing to existing cameras: 1 Remove the coaxial cable connected to the camera and the DVR 2 Connect the transmitter to the camera 3 Connect the coaxial cable to the

9 transmitter 4 Connect the coaxial cable to the BNC connector of the receiver 5 Connect the video out port of the receiver to the DVR or Monitor 6 Turn the receiver s power on Please turn on the power of the receiver (SC-VRPXXXX) only after the connection of all the equipments is done. When transmitting only video signals: When you use external power supply for the cameras and do not want to use the power supply function of the transmitter, the power output (DC Jack) at transmitter should be taped tightly not to be exposed BEFORE INSTALLING Before installing the units, please check if the camera power consumption, the distance and the coaxial cable quality are suitable with the units. Camera Power Consumption Max. Transmission Distance for Video and power Cable VCP0601/4/4H/8 DC 12V 0.5A / Max. 6W VCP1501/4 DC 12V 1.3A / Max. 15W VCP2501 DC 12V 2.5A / Max. 30W VCP0601/4/4H/8 Power+ Video: up to 1Km VCP1501/4 Power: up to 600m, Video: up to 1Km VCP2501 Power: up to 300m, Video: up to 1Km RG-6 (coaxial cable with 90% copper wire recommendable) The transmission distance may vary depending on the coaxial cable loop resistance, power consumption of the camera and other installation environment CONNECTION DIAGRAM Please refer to the below diagram when connection the equipments SC-VCP0601 When the power port of the camera is not DC- Jack type, please remove the harness and then the external cover of the power cable before connecting Adaptor

10 SC-VCP SC-VCP SC-VCP1501 Adaptor

11 SC-VCP SC-VCP2501 Adaptor 3-4. PRECAUTION & TROUBLESHOOTING SYMPTOMS CHECK POINT AND SOLUTION LED indicator of receivers is not working after power is on. VIDEO LOSS Please check the power cord at the backside of receiver Check the Transmitter connection Check the short circuit or disconnection of the cable. When the power adaptor is not working due to the short circuit of the cable, please remove the short circuits and then connect again the power adaptor. Normally, the receiver shut down the power when there is a short circuit of the cable. But, sometimes the power adaptor may operate the OCP (Over Current Protection)* function before the receiver does. Check the Camera (Ex.: using our Portable test

12 INTERFERENCE IS NOT REDUCED RED LED is turn on Release Version 1.7 monitor SC-LFC56L) Please check whether you use the standard coaxial cable or not. Please check the connection of the coaxial cable and the BNC connection status. Check whether the video input port is connected with an RCA cable besides a coaxial cable. The cable is disconnected or a short circuit was produced under 300m. Please check the cable. * OCP (Over Current Protection) Function: The power adaptor has the OCP function in order to protect from excessive current flow when there is short circuit of the coaxial cable. Our VP solutions are designed to stop supplying power when there is a short circuit of the cable. But, some adaptors may operate the OCP function, before the receiver does, turning off the power of the receiver. In this case, the receiver will work again when you supply power to the unit after the short circuit problem is solved. 4. MAX. TRANSMISSION DISTANCE PER CABLE 4-1. IN CASE OF SC-VCP06XX Please note that the video and power transmission distance may vary depending on the installation condition such as the cable loop resistance, the power of the camera and so on. Cable Power Distance Power Out Video Distance 3C-2V 400m 12VDC 500mA 400m RG m 12VDC 500mA 600m RG-6 (5C-2V) 1Km 12VDC 500mA 1Km The maximum power output is up to 12VDC / 500mA per each channel. In case of SC-VRP0604(H), when the total supplied power for the 4 cameras is over 20W, some cameras may not work properly. In case of SC-VRP0608, when the total supplied power for the 4 cameras from ch #1 to ch #4 or from ch #5 to ch #8 is over 20W, some cameras may not work properly. Please note that video transmission performance may vary depending on the camera, cable, cable length and so on. If the units fail to work properly, please contact your distributor.

13 5. SPECIFICATION VIDEO IN MODEL POWER OUT DC 12V, 0.5A BANDWIDTH MAX. DISTANCE CONNECTION PORT IN/OUT RF OUT SC-VTP0601 (TX.) CVBS 1.0Vp-p, 75Ω TERM. 8MHz 1Km DC-F & BNC-M Harness(25Cm) BNC-F TEMPERATURE / HUMIDITY -10 C ~ +50 C / 0 ~ 80% BODY / WEIGHT DIMENSION Aluminum/ 100g 76(W) x 42(H)x 25(D)mm VIDEO IN MODEL POWER OUT DC 12V, 1.3A BANDWIDTH MAX. DISTANCE CONNECTION PORT IN/OUT RF OUT SC-VTP1501 (TX) CVBS 1.0Vp-p, 75Ω TERM. 8MHz 600m (Camera power consumption: 15W / RG-6 with Loop Resistance Max 25Ω) DC-F & BNC-M Harness(45Cm) BNC-F TEMPERATURE / HUMIDITY -10 C ~ +50 C / 0 ~ 80% BODY / WEIGHT DIMENSION Aluminum/ 140g 78(W) x 60(H)x 25(D)mm VIDEO IN MODEL POWER OUT DC 12V, 2.5A BANDWIDTH SC-VTP2501 (TX.) CVBS 1.0Vp-p, 75Ω TERM. 8MHz MAX. DISTANCE 300m(RG-6 / Loop Resistance Max. 13Ω) CONNECTION PORT VIDEO IN DC12V OUT RF OUT 2Pin Terminal Block 2Pin Terminal Block BNC-F TEMPERATURE / HUMIDITY -10 C ~ +50 C / 0 ~ 80% BODY / WEIGHT DIMENSION(MM) PC & ABS / 720g 147(W) x 205(H)x 65(D)mm

14 VIDEO OUT POWER IN BANDWIDTH MODEL MAX. DISTANCE STATUS LED (Red Color ) CONNECTION PORT SC-VRP0601/1501/2501 (1CH RX.) CVBS 1.0Vp-p, 75Ω TERM. 0601/1501 AC/DC Adapter +48V 1.04A 2501 AC/DC Adapter +48V 1.875A VIDEO OUT RF IN 8MHz Auto adjustment Flickering: Check On: Normal BNC-M Harness(60Cm) BNC-F TEMPERATURE / HUMIDITY -10 C ~ +50 C / 0 ~ 80% BODY / WEIGHT DIMENSION Aluminum / 130g 78(W) x 60(H)x 25(D)mm VIDEO OUT POWER IN BANDWIDTH MODEL MAX. DISTANCE STATUS LED (Red Color ) CONNECTION PORT VIDEO OUT RF IN SC-VRP0604 (4CH RX.) CVBS 1.0Vp-p, 75Ω TERM. AC 100~240V, 50/60Hz 8MHz Auto Adjustment DC 48V 1.04A(Half type) Green: Normal, Red: Link Error BNC-M Harness(60Cm) BNC-F TEMPERATURE / HUMIDITY -10 C ~ +50 C / 0 ~ 80% BODY / WEIGHT DIMENSION Full Type Half Type Full Type Half Type Steel 3.5Kg Steel 1.4Kg 430(W) x 44(H) x 350(D)mm 246(W) x 44(H) x 190(D)mm

15 MODEL VIDEO OUT POWER IN BANDWIDTH MAX. DISTANCE STATUS LED (Red Color ) SC-VRP0608 (8CH RX.) CVBS 1.0Vp-p, 75Ω TERM. AC 100~240V, 50/60Hz 8MHz Auto Adjustment Green: Normal, Red: Link Error CONNECTION PORT VIDEO OUT RF IN BNC-M Harness(60Cm) BNC-F TEMPERATURE / HUMIDITY -10 C ~ +50 C / 0 ~ 80% BODY / WEIGHT DIMENSION Steel 3.5Kg 430(W) x 44(H) x 350(D)mm MODEL VIDEO OUT POWER IN BANDWIDTH MAX. DISTANCE STATUS LED (Red Color ) SC-VRP1504 (4CH RX.) CVBS 1.0Vp-p, 75Ω TERM. AC 100~240V, 50/60Hz 8MHz Auto Adjustment Green: Normal, Red: Link Error CONNECTION PORT VIDEO OUT RF IN BNC-M Harness(60Cm) BNC-F TEMPERATURE / HUMIDITY -10 C ~ +40 C / 0 ~ 80% BODY / WEIGHT DIMENSION Steel 3.5Kg 430(W) x 44(H) x 350(D)mm

16 6. Warranty Certificate This product has passed thorough quality control and test, and if this gets broken during normal use, we provide 12 months warranty service. Model No. Serial No. Distributor Date you purchased Place you purchased Warranty Period Name Customer Address One (1) year from the date of purchase Check this warranty first. Please contact the distributor after checking out any defect in the product. The standard for repairing, replacement or reimbursement follows Customer. Warranty content any defect under normal use within the warranty service period we give you free repair service according to the warranty certificate. We charge you with the fee of parts and service despite free warranty service period. 1. Any breakage made without care. 2. Breakage or trouble made by natural disaster. 3. Breakage or trouble made by breaking the product guide or manual. 4. Breakage or trouble made by wrong power voltage or frequency. 5. When you want to reassemble for full system or replace parts within warranty service period. 6. When unauthorized person modified or made damage on the product trying to repair it, we may charge you with the fee. Please note that we don t support the breakage after warranty service period. If the customer wants to get it repaired, we charge them with the fee. The specification is subject to change without prior notice for quality improvement. is new corporate name of Samsung CCTV Service Co.,Ltd

17 502~506, Sunil Technopia, 440, Sangdaewon-Dong, Jungwon-Gu, Sungnam-Si, Gyeonggi-do, Korea TEL : +82-(0) FAX : +82-(0)