Setup and Installation Guide

Transcription

1 Setup and Installation Guide Mini WiFi Transceiver for Smartphone Surveillance System with Motion-Detect Recording Function Connecting to Home Door Camera Window Camera Mini SPY Camera And more. WiFi Transceiver P1

2 Setup and Installation Guide Outline The setup and installation guide for this mini portable WiFi Transceiver system is divide into following sections. Table of contents: Page 1. Understand the Mini WiFi Transceiver (TXRX) Basic Concept of a WiFi Transceiver Diverse applications of an iat101 WiFi A/V transceiver a) Fixed Point WiFi Applications b) Portable WiFi Applications Software Installation on your phone Operation procedures for the WiFi Transceiver Modes of Operations Setup for ios (iphone) Setup for Android phone Other Setup information For Client Mode operation Appendix After you changing the WiFi encryption How to removing the host WiFi connection information In case there are any question, please us ia-tecs@hotmail.com or shop@iat101.com P2

3 1. Understand the mini WiFi Transceiver (TXRX) with Recording Function Smallest Dimension in the world 1) SD card slot 2) USB interface 3) REC Button 4) WI-FI On/ Off Button 5) Power Button 6) Microphone 7) Red LED (Red/No SD Card) 8) Green LED (WI-FI / Client) 9) Blue LED (Power ON) WiFi Audio / Video Transceiver cm 10 ) Analog Audio / Video In 1cm 2 P3

4 Basic Concept of a WiFi Transceiver (TXRX) The WiFi Transceiver (TXRX) is a device allowing you input analog A/V signal into the device ( ports 10), and the WiFi TXRX device will convert it into digital A/V and transmit the digital A/V signal from the built-in antenna into free space as a wireless WiFi signal. This WiFi signal is going to link with the WiFi connection in your iphone, ipad, Android Phone, or PC. This link is a WiFi peer to peer (P2P) Wi-Fi direct IP address connection using ad-hoc mode. This is not a WiFi device operated in infrastructure mode for internet connection applications This device is different from conventional analog RF wireless (2.4GH or 5.8GHz) A/V signal, the WiFi signal is secured with password. Other people will not be able to use a receiver to steal your video / audio signal. 1) SD card slot 2) USB interface 3) REC Button 4) WI-FI On/ Off Button 5) Power Button 6) Microphone 7) Red LED (Red/No SD Card) 8) Green LED (WI-FI / Client) 9) Blue LED (Power ON) 10 ) Analog Audio / Video In P4

5 Diverse applications of an iat101 WiFi A/V Transceiver Fixed Point WiFi Applications Powered on using a wall plug Portable WiFi Applications Powered on using a battery Compatible to most of iat101 s Door Cameras, and Window Cameras home/ office surveillance products Compatible to most of iat101 s Mini SPY Cameras, Dental camera as a portable surveillance products P5

6 Fixed Point WiFi Applications Powered on using a wall plug Connecting any analog surveillance camera video signal to the WiFi transceiver Window Camera Outdoor Camera Door Camera Video Signal in iat101 WiFi TXRX 8GB Micro SD card DC power in from a wall plug Note: For buying any door cameras, and window cameras, please visit our on-line shopping store P6

7 Typical wire connection diagram for a Fixed Point WiFi Surveillance Fixed Point WiFi Applications Powered on using a wall plug Analog Camera Such as iat101 s door camera, and window camera products WiFisignal to smartphone, ipad, and PCs 12 V DC Power Supply Analog A/V input from camera Mini WiFiTransceiver P7

8 Portable WiFi Applications Powered on using a battery Connecting any portable camera video signal to the WiFi transceiver Eye Glass Camera Audio /Video Signal in Other Compatible Portable Cameras Mini Camera Hidden SPY Camera Dental Camera And more iat101 WiFi TXRX 8GB Micro SD Micro USB connector to power on the WiFi Transceiver For buying compatible portable cameras, Please visit our website Or us at ia-tecs@hotmail.com 90cm long USB cable (white color) 5V Battery P8

9 2. Software Installation on a Smart Phone ( iphone & Android Phone ) a.) Install APPs software: Software download, please go to Google Play ( for Android) APP Store (for iso) to install SecurePro plus software,after download and the icon should shown in your apps list. b.) Power on WiFi transmitter and Turn on your Smartphone Wi-Fi setting, Search and Select SSID: WF-DV-LT1-xxxxxxxxxxxxx, and then input password: (Default SSID: WF-DV-LT1xxxxxxxxxxxxx / Password: ) c.) Barcode Scanning: After establishing the WiFi connection, and then click into get into device list window. For the first time user, please click into + sign on the left bottom corner and a bar code scanner window will appear. Please scan the barcode attached on the WiFi transmitter. After a successful bar code scanning, the SSID will shown in the device list. d.) Click device in the device list window, and input password one more time to link (Default Password: ) And then you should be able to the video shown on your Smartphone / Tablet. You may change Wi-Fi password, video settings, etc. (check Note1) Note 1: If you want to change the default password to your own password, you must write down and remember your own password and don t forget it. There is no way to reset password, if you forgot your password. P9

10 3. Operation procedures for the WiFi Transceiver Before the operation procedures, please make sure the A/V signal is plug into (10) A/V input slot. 1.) Insert the Micro SD card into (1): Place the SD Card into SD Card Slot, Press again for take out the SD Card. 2.) Plug in the Micro USB 5 V (DC) power supply to (2) 3.) Power On: Press button (5) of the device. Press again for powering off. Note: The default setting of the device as you power it on, its WiFi would be turn on and start recording. 4.) Wi-Fi On/Off: Press button (4) to turn on or turn off WiFi 5.) REC On/Off: Press button (3) to turn on or stop Recording. 6.) WiFi Direct / Wi-Fi Client Switch: Press button (4) for 3 sec. to switch the operational mode between WiFi- Direct or Wi-Fi Client mode. (please check next page for client mode information) 7.) Rest Wi-Fi to default: Hold the button (4) for 10 sec. LED light indications on the device: 1.) Blue LED Light On:Power On 2.) Red LED Light On:Please check the SD card. (Check the memory card) Red LED Light Blinking:Recording 3) Green LED Light On:WI-FI On Green LED Light Blinking:WI-FI Direct / WI-FI Client connecting Green LED Light Continue Blink 2 times and stop one sec.:enter Client, But no connection. 1) SD card slot 2) USB interface 3) REC Button 4) WI-FI On/ Off Button 5) Power Button 6) Microphone 7) Red LED (Red/No SD Card) 8) Green LED (WI-FI / Client) 9) Blue LED (Power ON) 10 ) Analog Audio / Video In P10

11 4. Modes of Operation There are 2 modes of operation can be used for the WiFi transceiver, WiFi Direct mode, and WiFi Client mode. The advantages of the WiFi Client mode are: 1. You may attach the WiFi transceiver to a WiFi router or AP s SSID, and then no one else will see your WiFi transceiver SSID. 2. The video transmission distance can be extended from 10 meters (WiFi Direct mode) to more than 30 meters (depending on your Router / AP transmission power) *The default setting is WI-FI direct connect mode, to use the WI-FI Client mode, please enter the direct connection mode, set client mode to connect to the APP, after the AP name and password, and then switch to the WI-FI client mode. *When the device switch to Client Mode, please make sure it is under signal of AP to avoid the disconnect Router / AP Please make sure, you do press button (4) for 3 sec. to switch the operational mode between WiFi- Direct or Wi-Fi Client mode. P11

12 5. For ios phone setup for iphone Before the setup, please make sure you download the software as described in page 9 DV-LT1-XXXXXXXXXX 1)Choose settings 2)Choose Wi-Fi. 3)Choosing the host s Wi-Fi which you need to connect. 4)Enter password. (The factory initial password is ) 5)Confirm WI-FI has been connected. 6.)Enter WI-FI connection. After finish setup please go to page 14 P12

13 6. For Android Phone Setup Before the setup, please make sure you download the software as described in page 9 DV-LT1- XXXXXXXXXX DV-LT1-XXXXXXXXXX DV-LT1- XXXXXXXXXX 1) Start APP. 2) Choose the WiFi device. 3) Enter password. (The factory password is ) 4) Click WiFi Connect 5.) Enter WI-FI connection. Note: Different smartphone may has different operational display screen After finish setup please go to page 14 P13

14 Functional Buttons 7. Other Setup Information Recording 1)Back to WI-FI device list. 2)Cell phone video and Photo archive folder. 3)SD card video host and Photo archive folder. 4)Setting. 5)Quick setting. 6)Host SD card resolution when recording. 7)SD card reminder. 8)Motion detection recording. 9)Resolution when recording. 10)Host SD card recording icon. 11)Host SD card recording. 12)Host SD card photograph. 13)Smartphone recording icon. 14)Smartphone recording. 15)Smartphone photograph. 16)Host SD card recording button. 17)Smartphone recording button Browsing mobile video /photo archive information 1)Film archives. 2)Photographic archives. 3)Film and photo all archive. 4)Mark archive what you need. 5)File name. 6)Mark all archive. 7)Unmark all archive. 8)Back to homepage. 9)Play button. 10)Delete button. Play video file 1)Host SD card red light constant lighting when recording. 2)Smartphone recording red light blinking. 1)Video playback window. 2)Back to last page. 3)Pause button. P14

15 Browsing the host SD card video / photo archive information 1)Film archives. 2)Photographic archives. 3)Film and photo all archive. 4)Continuous video file named beginning with Rec. 5)Motion detection recording named beginning w/mrec. 6)Mark archive what you need. 7)File name. 8)Mark all archive. 9)Unmark all archive. 10)Back to homepage. 11)Download archive of SD card to smartphone. 12)Play button. 13)Delete button. Setting 1)WI-FI setting. 2)Privacy setting. (After switch privacy setting, entry APP and enter password.) 3)Video setting. 4)Date and time setting. 5)System information. 6)Reset all setting. 7)Firmware upgrade. 8)Back to homepage. P15

16 *Click SecurePro APP, go into the WI-FI device list which you need to connect, and select 2 (you don t need to connect to the host Wi-Fi), and then you can view previous saved video files. Photo files were downloaded to the mobile video, and you can view Photo archive files. 1)Last connected Wi-Fi host. 2)Browsing files icon. WiFi Direct: WI-FI setting Encryption 1)Wi-Fi host name. 2)Wi-Fi password. 3)Way of encryption. 4)Set WI-FI SSID invisible or not. 5)Back to homepage. 6)Back to last page. 1)Way of encryption. 2)Visible. 3)WEP encrypt(64bit): Original password )WPA/WPA2/PSK encrypt(128bit): Original password Please also read Appendix 1 after you changed the WiFi encryption P16

17 WI-FI OFF Setting 1) WI-FI OFF 2) When the phone stops with the host connection, the host does not close the WI-FI 3) When the phone stops up to 1 minute to connect with the host, the host close WI-FI. 4) When the phone stops up to 3 minutes to connect with the host, the host close WI-FI. 5) When the phone stops up to 5 minutes to connect with the host, the host close WI-FI. * When the host is down WI-FI, required from the host operating P17

18 Image Setting Record Setting D1 1)Play parameters. 2)Resolution. (D1) 3)Frame choice. D1: ( ) 1)Recording mode selection. (Continuous recording or Motion detection) 2)Recording time. ( mins) 3) SD Over Write:(when SD card memory full) White dot on the left:overwrite Setting off. White dot on the right:overwrite Setting on. 4)Back to homepage. 5)Back to last page. Date and Time setting 1)Time display function: White dot to the left:date display close. White dot to the right:date display open. 2)Date format. 3)Time format. 4)Synchronization with device time. 5)Confirm the setting. System information 1)SD Capacity. 2)SD Usage rate. 3)APP Version. 4)Device initial firmware version. * Upgrading method of devices: Writing the initial firmware on SD card then put the SD card into device, connecting device with APP, and choose initial firmware version. P18

19 Reset all setting Other Functions 1)Quick setting. 2)Resolution setting. (D1) 3)Brightness setting. 4)Contrast setting. 5)Flip Top to Bottom. 6)Mirror left-right model. 7)Mic volume when recording. Black camouflage screen shortcuts When black camouflage screen, slide from right to left to exit black screen. P19

20 Rotate the smartphone for viewing a larger display P20

21 8. For Client Mode operation Please make sure, you do press button (4) for 3 sec. to switch the operational mode from WiFi- Direct to Wi-Fi Client mode first. 1)Select Client for Router Parameters. 2)Router name. 3)Router password. 4)Device name. Check the list of connected WiFi device, and select the corresponding router name. Select corresponding router name. 1)Privacy setting. (After privacy on, enter password.) White dot to the left:privacy off White dot to the right:privacy on 2)Privacy password. (Only number, no word limit.) 3)Confirm password again. 4)Back to homepage. 5)Back to last page. P21

22 9. Appendix * After changing encryption, please make sure you entry the WI-FI options of the device and clear connection information of device, then connecting back to the hosted WiFidevice again to ensure the changing of encryption method is successful. (Note: Different smartphone may has different operational screen.) Clear P22

23 *ios:how to removing the host WI-FI connection information. P23

24 We are specialized on varies design of 1. Door Camera, Window Camera, and Hidden SPY Cameras for Home / Office surveillance system 2. Personal portable hidden camera DVR kits 3. And more customized design to come In case there are any questions or product design requirements, please us ia-tecs@hotmail.com or shop@iat101.com Thank you for your reading our product manual! We look forward to assisting you with a good design solution matching your need.