RECOMMENDED SEQUENCE OF APPLICATION

Transcription

1 TOYOTA HIGHLANDER HANDS FREE BLUETOOTH Part Number: Accessory Code: BT4 CONFLICTS FACTORY BLUETOOTH SYSTEM AND JBL AUDIO GENERAL APPLICABILITY ALL MODELS WITHOUT FACTORY BLUETOOTH/JBL AUDIO KIT CONTENTS ITEM QTY DESCRIPTION 1 1 INTERFACE MODULE 2 1 INTERFACE RADIO/POWER HARNESS 3 1 SYSTEM SWITCH 4 1 MICROPHONE PACK 5 1 HARDWARE BAG 6 2 FOAM ADHESIVE STRIP 7 1 QUICK GUIDE STICKER 8 1 OWNER S MANUAL RECOMMENDED SEQUENCE OF APPLICATION ALL APPLICATIONS REQUIRING REMOVAL OF A PILLAR COMPLETED BEFORE INSTALLING MICROPHONE. * MANDATORY HARDWARE BAG CONTENTS ITEM QTY DESCRIPTION 1 12 WIRE TIES 2 1 ADHESIVE FOAM PAD ADDITIONAL ITEMS REQUIRED FOR INSTALL ITEM QTY DESCRIPTION 1 N/A ELECTRICAL TAPE RECOMMENDED TOOLS SAFETY TOOLS SPECIAL TOOLS INSTALLATION TOOLS FASTENER REMOVAL TOOL TRIM REMOVAL TOOL 8 & 10-MM DEEP SOCKET POWER DRILL/DRIVER WIRE CUTTERS NEEDLE-NOSE PLIERS SPECIAL CHEMICALS Southeast Toyota Distributors, LLC Page 1 of 8

2 PARTS IDENTIFICATION ITEM QTY DESCRIPTION PART NUMBER 1 1 INTERFACE MODULE INTERFACE HARNESS SYSTEM SWITCH MICROPHONE PACK INCL. IN ITEM HARDWARE BAG INCL. IN ITEM FOAM ADHESIVE STRIP INCL. IN ITEM QUICK GUIDE STICKER INCL. IN ITEM OWNER S MANUAL INCL. IN ITEM Southeast Toyota Distributors, LLC Page 2 of 8

3 VEHICLE PREPARATION CAUTION: IT IS ADVISABLE TO DISCONNECT THE NEGATIVE BATTERY CABLE FOR 3 MINUTES BEFORE BEGINNING INSTALLATION, TO AVOID UNINTENDED AIR BAG DEPLOYMENT. NOTE AND RECORD ANY ANTI- THEFT RADIO CODES PRIOR TO DISCONNECTING. VEHICLE PREPARATION 1. ENGAGE PARKING BRAKE. MOVE THE TRANSMISSION SHIFT LEVER INTO NEUTRAL POSITION. 2. APPLY PROTECTIVE TAPE UNDERNEATH THE HVAC AIR VENT ASSEMBLY AND USE A PANEL TOOL TO DISENGAGE THE CLIPS AND PULL THE VENT ASSEMBLY OUT. DISCONNECT ALL CON- NECTORS AND SET ASSEMBLY ASIDE. FIGURE 1 3. REMOVE THE CENTER INSTRUMENT CLUSTER FINISH PANEL USING A PANEL REMOVAL TOOL. APPLY PROTECTIVE TAPE TO THE AREA AND DISENGAGE THE CLIPS AND CLAWS. USE CARE NOT TO BEND AND CRACK THE PANEL. DISENGAGE THE HVAC ASSEMBLY BY PULLING STRAIGHT OUT. DISCONNECT ALL CON- NECTORS AND REMOVE. FIGURES 2-3 FIGURE 1 FIGURE 2 FIGURE 3 Southeast Toyota Distributors, LLC Page 3 of 8

4 INSTALLATION VEHICLE PREPARATION (CONT D) 1. REMOVE (2) 10MM BOLTS LOCATED ABOVE AND GENTLY PULL OUT THE RADIO ASSEMBLY, DISCONNECT THE CONNECTORS, AND SET ASIDE FIGURE 5. THE TWO BELOW THE RADIO ASSEMBLY. NOTE: BE CAREFUL NOT TO PUT EXCESSIVE TENSION ON THE RADIO CONNECTIONS WHEN PULLING OUT THE RADIO. SUPPORT THE ASSEMBLY ON A PROTECTED SURFACE TO PRE- VENT ANY DAMAGE TO THE CONNECTIONS OR THE DASH PANELS. MICROPHONE 1. REMOVE THE LEFT A-PILLAR BY PULLING IT AWAY FROM THE CHASSIS (DISENGAGING THE CLIPS) AND TWISTING THE PLASTIC TETHER CLIP WITH NEEDL-NOSE PLIERS TO FREE THE TETHER FROM THE PANEL. FIGURE 6 2. ROUTE FIGURE 5 THE MICROPHONE HARNESS ALONG THE FACTORY WIRING AND USE WIRE TIES TO SECURE IT AS SHOWN IN FIGURE 6. NOTE: TAKE CARE NOT TO SECURE THE HAR- NESS TO THE AIRBAG OR ANY OF ITS COMPONENTS. 3. REMOVE THE SHROUD COVERING THE INSTRUMENT CLUSTER AS SHOWN IN FIGURE 7. REMOVE THE FOUR REMOVE THE INSTRUMENT CLUSTER. ROUTE (4) SCREWS TO THE MICROPHONE HARNESS FROM THE PILLAR TO THE AREA BEHIND THE CLUSTER. REMOVE MOST OF THE SLACK AND SECURE THE MICRO- PHONE WIRE TO THE FACTORY WIRE LOOM. 4. REPLACE THE A-PILLAR PANEL. PRIOR TO FULLY SEATING THE CLIPS, CLEAN THE UPPER CORNER WITH THE SUPPLIED FIGURE 6 FIGURE 7 ALCOHOL PAD AND MOUNT THE MICROPHONE AS SHOWN IN FIGURE 8. REMOVE INSTRUMENT CLUSTER SHROUD BY DISENGAGING CLIPS FIGURE 8 Southeast Toyota Distributors, LLC Page 4 of 8

5 INSTALLATION SYSTEM SWITCH 1. DISENGAGE CENTER CONSOLE SUBASSEBLY AS SHOWN IN FIGURE 9. REMOVE THE LEFT BLANK KNOCKOUT. INSTALL THE SYSTEM SWITCH IN THE OPENING, MAKING SURE THE SOLID ARROW IS FACING FORWARD. FIGURE ROUTE THE SWITCH HARNESS TO THE RIGHT OF THE SHIFTER ASSEMBLY TOWARDS THE RADIO OPENING, AND THEN LEFT TO THE AREA BEHIND THE PREVIOUSLY REMOVED INSTRU- MENT CLUSTER. SECURE THE HARNESS TO THE FACTORY WIRE LOOM USING WIRE TIES AS SHOWN IN FIGURE 11. NOTE: FOR HIGHLANDER 4X4, USE THE SWITCH LOCATION AS SHOWN IN FIGURE 12. FOR HIGHLANDER HV, USE THE SWITCH LOCATION AS NOTED IN FIGURE 13. INSTALL THE SWITCH WITH THE SOLID ARROW POINTING UP. ROUTE THE HARNESS BEHNIDE THE RADIO SUPPORTS TO THE INTERFACE MODULE AND SECURE WITH WIRE TIES. FIGURE 9 FIGURE 10 HIGHLANDER 4X4 FIGURE 11 FIGURE 12 HIGHLANDER HV FIGURE 13 Southeast Toyota Distributors, LLC Page 5 of 8

6 INSTALLATION INTERFACE MODULE 1. CONNECT THE INTERFACE RADIO/POWER HARNESS, SWITCH SWITCH HARNESS, AND MICROPHONE HARNESS TO THE INTERFACE MODULE AS SHOWN IN FIGURE 14. USE MICROPHONE RADIO/PWR A PIECE OF THE SUPPLIED FOAM TAPE TO COVER THE FUSE ON THE HARNESS AS SHOWN IN 2. MOUNT FIGURE 15. THE INTERFACE MODULE TO THE WIRE HARNESS ON BEHIND THE INSTRUMENT CLUSTER. SECURE THE MODULE FIGURE 14 WITH WIRE TIES BY USING THE WIRE TIE CHANNELS AT EACH END OF THE MODULE. 3. ROUTE TER OF THE NESS. TIES. THE IP FIGURE 16 RADIO/POWER HARNESS THROUGH THE CEN- AND PLUG IT INTO THE VEHICLE RADIO HAR- SECURE IT TO FIGURE 17 THE FACTORY WIRE LOOM USING WIRE CONTROL MODULE MOUNTED TO WIRE LOOM BEHIND CLUSTER FIGURE 15 FIGURE 16 FIGURE 17 Southeast Toyota Distributors, LLC Page 6 of 8

7 INSTALLATION RADIO AND REASSEMBLY 1. CONNECT THE MAIN INTERFACE POWER HARNESS CONNEC- TORS TO THE FACTORY RADIO WIRE LOOM AND THE RADIO BY MATCHING THE CONNECTORS. MAKE SURE ALL CONNECTIONS ARE SECURELY SEATED. NOTE: AVC-LAN (12-PIN) CONNECTOR MAY NOT BE PRESENT ON THE VEHICLE S HARNESS. WIRE TIE THIS CONNECTOR TO THE HARNESS UNCONNECTED, BUT ALWAYS CONNECT THE AVC-LAN (12-PIN) CONNECTOR INTO THE RADIO. IF AVC-LAN (12-PIN) CONNECTOR IS PRESENT INTHE VEHICLE HARNESS, CONNECT TO THE MAIN INTERFACE POWER HARNESS. IF ANY OTHER ACCESSORIES ARE INSTALLED THAT CONNECT TO THE HEAD UNIT, THE HANDS FREE SYSTEM SHOULD BE THE ACCESSORY THAT PLUGS INTO THE RADIO FIRST. FIGURE REINSTALL ALL TRIM PANELS IN THE ORDER OF REMOVAL, TAKING SPECIAL CARE TO MAKE SURE ALL HARNESSES AND WIRING ARE PROPERLY SECURED. MAKE SURE HARNESSES ARE NOT PINCHED OR BOUND BY TRIM PIECES. PLACE THE OWNER S MANUAL AND QUICK GUIDE STICKER IN THE GLOVE BOX. 3. RECONNECT NEGATIVE BATTERY CABLE AND TORQUE TO 3 FT LBS. RE-ENTER ANY THEFT DETERRENT INFORMATION, IF APPLICABLE. Southeast Toyota Distributors, LLC Page 7 of 8

8 TOYOTA HIGHLANDER HANDS FREE CELL PHONE SYSTEM Southeast Toyota Distributors, LLC Page 8 of 8