Bubble CPAP System PRODUCT CATALOGUE

Transcription

1 Bubble CPAP System PRODUCT CATALOGUE

2

3 Bubble CPAP Contents Section Delivery Systems 1 Diagrams 1.1 Infant Delivery System (BC151) 1.2 Infant Delivery System (BC161) 1.2 Infant Delivery System (BC171) 1.2 Patient Interface 2 Nasal Tubing Midline 2.1 Nasal Tubing Universal 2.1 Nasal Prongs 2.1 Infant Bonnet Midline 2.1 Headgear Midline 2.1 Chinstrap 2.1 Bubble CPAP System Starter Kits 3 Starter Kit Midline Delivery System 3.1 Starter Kit I/F (Flow Driver compatible) Delivery System 3.1 Nasal Prong Starter Kit 3.2 Infant Bonnet Starter Kit 3.2 Starter Kit Midline F&P 50mm 3.2 Starter Kit Midline F&P 70mm 3.2 Starter Kit Midline F&P 100mm 3.2 Starter Kit Midline Universal 50mm 3.3 Starter Kit Midline Universal 70mm 3.3 Starter Kit Midline Universal 100mm 3.3 Accessories / Devices 4 Single-Use Gas Supply Line 2.1m 4.1 Gas Supply Line to 2 flow meters 4.1 Midline Pressure Luer Adaptor 4.1 Mounting Options Humidifier Stand Telescopic 4.2 Mounting Bracket C-Clamp 4.2 Mounting Bracket Pole 15-50mm 4.2 Humidification Humidifier 4.3 Heater Wire Adaptor MR Heater Wire/Temp Probe Kit 4.3 Probe Temp/Flow Ang 1600mm 4.3 Gas Supply Bird MBlender 2-16LPM DISS 4.3 Bird MBlender 2-16LPM NIST 4.3 Bird MBlender Pole Mount Bracket 4.3 Sample Setups 5 Pole Mount Setup 5.1 Infant Warmer Setup 5.2

4 Bubble CPAP Delivery Systems 1.1 BC161 BC BC

5 Bubble CPAP Delivery Systems 1.2 MR290 Chamber Product Code BC Includes BC Includes BC171-10* Includes Description Infant Delivery System MR290 chamber Pressure Manifold CPAP Generator Single-heated Circuit Infant Delivery System MR290 chamber Pressure Manifold CPAP Generator Single-heated Circuit Infant Delivery System MR290 chamber Simplified Pressure Manifold (with attached dry line) CPAP Generator Single-heated Circuit Pressure Damping Filter * Flow Driver compatible circuit Pressure Manifold Simplified Pressure Manifold (BC only) Single Heated Circuit Pressure Damping Filter (BC only) CPAP Generator

6 Bubble CPAP Patient Interface 2.1 Length in mm Product Code Description Size Nasal Tubing Midline (BC18x series) Nasal Tubing Universal (BC19x series) Diameter of nares Septum gap Nasal Prongs Nasal Tubing Length BC Nasal tubing 50mm x5 50mm BC Nasal tubing 70mm x5 70mm BC Nasal tubing 100mm x5 100mm BC Nasal tubing Universal 50mm x5 50mm BC Nasal tubing Universal 70mm x5 70mm BC Nasal tubing Universal 100mm x5 100mm Nasal Prongs diameter of nares / width of septum BC Nasal prong /bx 3.0mm / 2.0mm BC Nasal prong /bx 3.5mm / 2.0mm BC Nasal prong /bx 4.0mm / 3.0mm BC Nasal prong /bx 4.5mm / 4.0mm BC Nasal prong /bx 5.0mm / 4.0mm BC Nasal prong /bx 5.0mm / 5.0mm BC Nasal prong /bx 5.5mm / 5.0mm BC Nasal prong /bx 5.5mm / 6.0mm BC Nasal prong /bx 6.0mm / 6.0mm BC Nasal prong /bx 6.0mm / 7.0mm BC Nasal prong /bx 6.5mm / 7.0mm Product Code Description Size Infant Bonnet head circumference BC Infant Bonnet Midline 17-22cm x5 17cm-22cm BC Infant Bonnet Midline 22-25cm x5 22cm-25cm BC Infant Bonnet Midline 25-29cm x5 25cm-29cm BC Infant Bonnet Midline 29-36cm x5 29cm-36cm Infant Bonnet Product Code Description Size Headgear head circumference BC Headgear Midline 29-36cm x5 29cm-36cm BC Headgear Midline 35-40cm x5 35cm-40cm BC Headgear Midline 40-45cm x5 40cm-45cm Headgear Chinstrap face circumference BC Chinstrap 20-26cm x10 20cm-26cm BC Chinstrap 26-32cm x10 26cm-32cm BC Chinstrap 32-38cm x10 32cm-38cm BC Chinstrap 38-44cm x10 38cm-44cm Chinstrap

7 Bubble CPAP Bubble CPAP System Starter Kits 3.1 Product Code Description Simplified Pressure Manifold (BC171 only) Infant Bonnet Nasal Tubing Nasal Prongs Damping Filter (BC171 only) BC461-SK Includes Starter Kit Midline Delivery System 5 BC161 Infant Delivery System 5 Nasal tubing 70mm 2 Infant Bonnet 17-22cm 3 Infant Bonnet 22-25cm 3 Infant Bonnet 25-29cm 2 Infant Bonnet 29-36cm 2 Nasal Prong Nasal Prong Nasal Prong Nasal Prong Nasal Prong Nasal Prong Nasal Prong Nasal Prong Nasal Prong 6070 BC471-SK* Starter Kit I/F Delivery System Includes 5 BC171 Infant Delivery System (with simplified pressure manifold and pressure damping filter) 5 Nasal tubing 70mm 2 Infant Bonnet 17-22cm 3 Infant Bonnet 22-25cm 3 Infant Bonnet 25-29cm 2 Infant Bonnet 29-36cm 2 Nasal Prong Nasal Prong Nasal Prong Nasal Prong Nasal Prong Nasal Prong Nasal Prong Nasal Prong Nasal Prong 6070 * Flow Driver compatible circuit Infant Flow compatible circuit CPAP Generator Pressure Manifold MR290 Chamber

8 Bubble CPAP Patient Interface Starter Kits 3.2 Product Code Description Nasal Prongs BC260-SK Nasal Prong Starter Kit Includes 2 Nasal Prong Nasal Prong Nasal Prong Nasal Prong Nasal Prong Nasal Prong Nasal Prong Nasal Prong Nasal Prong 6070 Infant Bonnet Nasal Tubing BC360-SK Infant Bonnet Starter Kit Includes 2 Infant Bonnet 17-22cm 3 Infant Bonnet 22-25cm 3 Infant Bonnet 25-29cm 2 Infant Bonnet 29-36cm BC480-SK Starter Kit Midline F&P 50mm Includes 3 Nasal tubing 50mm 2 Nasal Prong Nasal Prong Nasal Prong Nasal Prong Infant Bonnet 17-22cm 2 Infant Bonnet 22-25cm 1 Infant Bonnet 25-29cm BC481-SK Starter Kit Midline F&P 70mm Includes 3 Nasal tubing 70mm 2 Nasal Prong Nasal Prong Nasal Prong Nasal Prong Infant Bonnet 17-22cm 2 Infant Bonnet 22-25cm 1 Infant Bonnet 25-29cm BC482-SK Starter Kit Midline F&P 100mm Includes 3 Nasal tubing 100mm 2 Nasal Prong Nasal Prong Nasal Prong Nasal Prong Infant Bonnet 22-25cm 2 Infant Bonnet 25-29cm 1 Infant Bonnet 29-36cm

9 Bubble CPAP Universal Patient Interface Starter Kits 3.3 The Universal Patient Interface Starter Kit is designed to allow connection of other single-heated circuits e.g. Cardinal and Hudson. Product Code Description Nasal Tubing BC490-SK Starter Kit Midline Universal 50mm Includes 3 Nasal Tubing Universal 50mm 2 Nasal Prong Nasal Prong Nasal Prong Nasal Prong Infant Bonnet 17-22cm 2 Infant Bonnet 22-25cm 1 Infant Bonnet 25-29cm Nasal Prongs BC491-SK Starter Kit Midline Universal 70mm Includes 3 Nasal Tubing Universal 70mm 2 Nasal Prong Nasal Prong Nasal Prong Nasal Prong Infant Bonnet 17-22cm 2 Infant Bonnet 22-25cm 1 Infant Bonnet 25-29cm Infant Bonnet BC492-SK Starter Kit Midline Universal 100mm Includes 3 Nasal Tubing Universal 100mm 2 Nasal Prong Nasal Prong Nasal Prong Nasal Prong Infant Bonnet 22-25cm 2 Infant Bonnet 25-29cm 1 Infant Bonnet 29-36cm

10 Bubble CPAP Accessories 4.1 Single-Use Product Code Description Gas Supply Line (to blender) BC Gas Supply Line 2.1m BC Gas Supply Line (to 2 flow meters) BC Midline Pressure Luer Adaptor Gas Supply Line (to 2 flow meters) Midline Pressure Luer Adaptor

11 Bubble CPAP Mounting Options 4.2 Product Code 900MR MR MR030 Description Humidifier Stand telescopic Mounting Bracket C-clamp Mounting Bracket Pole 15-50mm Telescopic Humidifier Stand C-Clamp Pole Clamp

12 Bubble CPAP Devices 4.3 Humidification Product Code MR MR MR MR868 Description Humidifier Heater Wire Adaptor MR850 Heater Wire/Temp Probe Kit Probe Temp/Flow Ang 1600mm MR850 Humidifier Temperature / Flow Probe Heater Wire Gas Supply Low Flow Air/O2 Blender Product Code BC BC BC BC BC Description Bird MBlender 2-16LPM DISS Bird MBlender 2-16LPM NIST Blender Oxy/Air Bio-Med (DISS) green Blender Oxy/Air Bio-Med (DISS) white Bird MBlender Pole Mount Bracket Bird MBlender Pole Mount Bracket Blender DISS & NIST fittings available BIO-MED DEVICES O 2% Gas Blenders are available on an individual basis. They come complete with color coded nipples and control knobs. Flowrate 2-16 L/min (Bird) 0-15 L/min (Bio-Med) Includes flowmeter nipples (green or white) Note: Requires 900IW320 Bird Bracket Blender Complete to be fitted to the CosyCot Infant Warmer. Gas hoses not included. Please refer to Fisher & Paykel Healthcare Infant Warming Catalogue.

13 Bubble CPAP Sample Setup (pole) 5.1 Bird MBlender 2-16LPM BC (DISS) BC (NIST) Low Flow Air/O2 Blender Note: Gas Hoses not included. Please refer to Fisher & Paykel Infant Warming Catalogue BC Bird MBlender Pole Mount Bracket MR850 Humidifier 900MR801 Heater Wire Adaptor MR MR030 Mounting Bracket Pole 15-50mm (for mounting humidifier) 900MR868 Probe Temp/Flow Ang 1600mm 900MR170 Mounting Bracket C-Clamp (for mounting CPAP generator) 900MR292 Humidifier Stand Telescopic

14 Bubble CPAP Sample Setup (warmer) 5.2 Low Flow Air/O2 Blender Bird MBlender 2-16LPM BC (DISS) BC (NIST) Note: Gas Hoses not included. Please refer to Fisher & Paykel Infant Warming Catalogue BC Bird MBlender Pole Mount Bracket MR850 Humidifier 900MR030 Mounting Bracket Pole 15-50mm (for mounting humidifier) 900MR801 Heater Wire Adaptor MR MR868 Probe Temp/Flow Ang 1600mm 900IW302 Mounting Pole long 900MR170 Mounting Bracket C-Clamp (for mounting CPAP generator)

15

16 MANUFACTURER Fisher & Paykel Healthcare Limited, 15 Maurice Paykel Place, East Tamaki, Auckland 2013; P O Box , Panmure, Auckland 1741, New Zealand Tel: Fax: info@fphcare.com Web Site: AUSTRALIA Tel: Fax: AUSTRIA Tel: Fax: BENELUX Tel: Fax: CHINA Tel: Fax: FRANCE Tel: Fax: GERMANY Tel: Fax: INDIA Tel: Fax: IRISH REPUBLIC Tel: ITALY Tel: Fax: JAPAN Tel: Fax: NORTHERN IRELAND Tel: SPAIN Tel: Fax: SWEDEN Tel: Fax: SWITZERLAND Tel: Fax: UK (EU Authorised Representative) Fisher & Paykel Healthcare Ltd, Unit 16, Cordwallis Park, Clivemont Road, Maidenhead, Berkshire SL6 7BU, United Kingdom Tel: Fax: USA Tel: or Fax: REF Rev F en

17 Bubble CPAP System Set-up Guide

18 For full User Instructions, please refer to Bubble CPAP System User Instructions (BC151/BC161 PN and BC171 PN ).

19 BC151 / BC161 BC161 (connects to F&P FlexiTrunk Interface) BC151 (connects to T-bar Interface) Checks During Operation Regularly observe that the water is feeding into the humidification chamber. Should the water level exceed the maximum level marked on the humidification chamber, the chamber should be replaced. Check that all connections are tight before use and after any adjustment. Ensure air flow is present at all times. If air flow is interrupted, turn off the humidifier. Regularly observe the circuit for condensate. Drain as required. Regularly observe the CPAP generator for bubbling. If bubbling is not observed, check for and minimize air leaks in the system and at the patient. If air leaks have been minimized, air flow may be increased to achieve continuous bubbling. Regularly observe the water level in the CPAP generator and overflow container. Refill the CPAP generator if the water level drops below the minimum water level line. Check and empty the overflow container once every 8 hours or as needed. Monitor patient oxygen levels. Always use pressure monitoring to verify that the patient is receiving the prescribed CPAP level. F & P b u b b l e c p a p s e t - u p G u i d e 1

20 BC151 / BC161 SET-UP 1. Insert Humidification Chamber Discard the chamber if the seals are not intact when received. Slide the chamber on to the humidifier base. Remove the blue caps. 2. Connect Water Bag Hang the water bag, unwind the water feed set and spike the water bag. Open the vent on the vented spike. Check the humidification chamber for water flow from the bag. If no water is visible in the chamber or water consumption is low, check that the bag is spiked properly and that the feed tube is not kinked or blocked. Try gently squeezing the bag to promote water flow. Ensure that the height of the water bag is at least higher than the humidification chamber. If in doubt replace the chamber. Discard the chamber if the water level exceeds the maximum water level line. 3. Fill Bubble CPAP Generator Using the fill-funnel provided, fill the CPAP generator with sterile water until water flows into the overflow container. Set the CPAP probe to 10 cmh 2 O, ready for the leak test. Ensure that the fill-funnel remains on the Bubble CPAP generator. Ensure that the humidifier and Bubble CPAP generator are mounted below the patient. Water level too low Water level correct 2 F & P b u b b l e c p a p s e t - u p G u i d e

21 4. Connect Bubble CPAP Pressure Manifold and Breathing Circuit Connect the oxygen tubing between the pressure manifold and the flow source. Connect the pressure manifold to the chamber inlet port. Connect the blue inspiratory tube to the remaining chamber port. Remove the blue caps from the inspiratory tube and install the temperature probe ports and heaterwire adapter. Ensure that the heater-wire (inside tube) is evenly distributed along the circuit length and is not bunched or kinked. Connect test elbow to expiratory and inspiratory limbs. 1 L/min Leak Test Check all connections are tight before use. Set the CPAP probe to 10 cmh 2 O and the input flow rate to 1 L/min. Observe the CPAP generator. Gentle, audible bubbling is acceptable; no bubbling means unacceptable leakage. If no bubbling is observed, check the entire system. Remove the correct port cap from the pressure manifold before connecting any monitoring device. 6-8 L/min (<15 L/min) 6. Set Flow Rate Adjust the flow rate to the prescribed input flow rate. Recommended flow rate: 6 to 8 L/min. Allowable flow range: 4 to 15 L/min. F & P b u b b l e c p a p s e t - u p G u i d e 3

22 BC151 / BC161 SET-UP Pressure-Flow Table F&P Bubble CPAP Generator used with F&P Infant Interface, typical mean pressure values (cmh 2 0) WITH NO LEAK Probe Setting (cmh 2 O) Flow (L/min) Note: Other interfaces or circuits may produce varying pressures Set CPAP Level The number on the CPAP probe above the lid indicates the CPAP pressure in cmh 2 O. As an example, the illustration shows CPAP setting of 6 cmh 2 O. Set the CPAP probe at the prescribed level (3 to 10 cmh 2 O). 4 F & P b u b b l e c p a p s e t - u p G u i d e

23 8. Connect Bubble CPAP Circuit to Infant Interface Remove the flow test elbow and connect the circuits to the Infant Interface using the instructions provided with the interface. BC161 connects to F&P FlexiTrunk Interface. BC151 connects to short binasal prongs (T-bar). MR850: 37 C 9. Set the Humidifier Ensure there is air flow present before turning on the humidifier. Turn on the humidifier. If using the MR850, ensure it is on Invasive mode (37 C). If using the MR730, set the temperature to 40 C, -3. Refer to the MR850 or MR730 User Instructions for further information. MR730: 40 C, Attach Interface to Infant Connect the interface to the infant using the instructions provided with the interface. BC161 BC151 F & P b u b b l e c p a p s e t - u p G u i d e 5

24 BC171 BC171 (connects to Flow Driver) Checks During Operation Regularly observe that the water is feeding into the humidification chamber. Should the water level exceed the maximum level marked on the humidification chamber, the chamber should be replaced. Check all connections are tight before use and after any adjustment. Ensure air flow is present at all times. If air flow is interrupted, turn off the humidifier. Regularly observe the circuit for condensate. Drain as required. Regularly observe the CPAP generator for bubbling. If bubbling is not observed, check for and minimize air leaks in the system and at the patient. If air leaks have been minimized, air flow may be increased to achieve continuous bubbling. Regularly observe the water level in the CPAP generator and overflow container. Refill the CPAP generator if the water level drops below the minimum water level line. Check and empty the overflow container once every 8 hours or as needed. Monitor patient oxygen levels. Always use pressure monitoring to verify that the patient is receiving the prescribed CPAP level. 6 F & P b u b b l e c p a p s e t - u p G u i d e

25 BC171 SET-UP 1. Insert Humidification Chamber Discard the chamber if the seals are not intact when received. Slide the chamber on to the humidifier base. Remove the blue caps. 2. Connect Water Bag Hang the water bag, unwind the water feed set and spike the water bag. Open the vent on the vented spike. Check the humidification chamber for water flow from the bag. If no water is visible in the chamber or water consumption is low, check that the bag is spiked properly and that the feed tube is not kinked or blocked. Try gently squeezing the bag to promote water flow. Ensure that the height of the water bag is at least 50 cm higher than the humidification chamber. If in doubt replace the chamber. Discard the chamber if the water level exceeds the maximum water level line. 3. Fill Bubble CPAP Generator Using the fill-funnel provided, fill the CPAP generator with sterile water until water flows into the overflow container. Set the CPAP probe to 10 cmh 2 O, ready for the leak test. Ensure that the fill-funnel remains on the Bubble CPAP generator. Ensure that the humidifier and Bubble CPAP generator are mounted below the patient. Water level too low Water level correct F & P b u b b l e c p a p s e t - u p G u i d e 7

26 BC171 SET-UP 4. Connect Pressure Manifold, Dry Line and Circuit Connect the pressure manifold with dry line to the flow driver and chamber inlet port. Connect the blue inspiratory limb to the remaining chamber port. Remove the blue caps from the inspiratory tube and install the temperature probe ports and the heaterwire adapter. Ensure that the heater wire is evenly distributed along the circuit length and is not bunched or kinked. Connect test elbow to expiratory and inspiratory limbs. 1 L/min Leak Test Check all connections are tight before use. Set the CPAP probe to 10 cmh 2 O and the input flow rate to 1 L/min. Observe the CPAP generator. Gentle, audible bubbling is acceptable; no bubbling means unacceptable leakage. If no bubbling is observed, check the entire system. 6. Set Flow Rate Adjust the flow rate to the prescribed input flow rate. Recommended flow rate: 6 to 8 L/min. Allowable flow range: 4 to 15 L/min. 6-8 L/min (<15 L/min) Set CPAP Level The number on the CPAP probe above the lid indicates the CPAP pressure in cmh 2 O. As an example, the illustration shows CPAP setting of 6 cmh 2 O. Set the CPAP probe at the prescribed level (3 to 10 cmh 2 O). 8 F & P b u b b l e c p a p s e t - u p G u i d e

27 Pressure-Flow Table F&P Bubble CPAP Generator used with F&P Infant Interface, typical mean pressure values (cmh 2 0) WITH NO LEAK Probe Setting (cmh 2 O) Flow (L/min) Note: Other interfaces or circuits may produce varying pressures. 7. Connect Bubble CPAP Circuit to Infant Interface Remove the flow test elbow and connect the circuits to the Infant Interface using the instructions provided with the interface. F & P b u b b l e c p a p s e t - u p G u i d e 9

28 BC171 SET-UP 8. Connect Pressure Line to Flow Driver Connect the pressure line filter end of the pressure line to the flow driver. Connect the pressure line elbow connector end of the pressure line to the nasal tubing pressure port. 9. Set the Humidifier (MR850) Ensure there is air flow present before turning on the humidifier. Turn on the flow driver. Turn on the humidifier. If using the MR850, ensure it is on Invasive mode (37 C). Refer to the MR850 User Instructions for further information. MR850: 37 C A 9A. Set the Humidifier (MR730) Ensure there is air flow present before turning on the humidifier. Turn on the flow driver. Turn on the humidifier. If using the MR730, set the temperature to 40 C, -3. Refer to the MR730 User Instructions for further information. MR730: 40 C, F & P b u b b l e c p a p s e t - u p G u i d e

29 10. Attach Interface to Infant Connect the interface to the infant using the instructions provided with the interface. BC171 F & P b u b b l e c p a p s e t - u p G u i d e 1 1

30 For more information please contact your local Fisher & Paykel Healthcare representative REVa EN 2011 Fisher & Paykel Healthcare Limited Manufacturer Fisher & Paykel Healthcare Ltd 15 Maurice Paykel Place East Tamaki, Auckland 2013 PO Box , Panmure Auckland 1741 New Zealand Tel: Fax: info@fphcare.com Web: Australia Fisher & Paykel Healthcare Pty Limited New Street, PO Box 167 Ringwood, Melbourne Victoria 3134, Australia Tel: Fax: Austria Tel: Fax: Benelux Tel: Fax: China Tel: Fax: France Tel: Fax: Germany Tel: Fax: India Tel: Fax: Irish Republic Tel: Italy Tel: Fax: Spain Tel: Fax: Sweden Tel: Fax: Switzerland Tel: Fax: Taiwan Tel: Fax: Turkey Tel: Fax: UK EC REP Fisher & Paykel Healthcare Ltd Unit 16, Cordwallis Park Clivemont Road, Maidenhead Berkshire SL6 7BU, UK Tel: Fax: USA/Canada Tel: or Fax:

31 Bubble CPAP System F&P Bubble CPAP SYSTEM With the goal of improving patient care in over 120 countries, Fisher & Paykel Healthcare designed the F&P Bubble CPAP System for use with spontaneously breathing infants requiring respiratory support. Incorporating unique features and world-leading humidification technology, the F&P Bubble CPAP System has been developed to provide a respiratory support system that is safe, effective and easy to use. Adaptability to current practices has been taken into consideration with the choice of various system models. The F&P Infant Interface complements the system, providing comfort and optimum CPAP support to the infant at risk.

32 F&P Bubble CPAP System FEATURES The F&P Bubble CPAP System is the first complete system available in an All-in-One Pack. It includes the Bubble CPAP generator, heated breathing circuits, humidification chamber and pressure manifold. F&P FlexiTrunk is a lightweight nasal tubing with a unique, flexible extension for a stable prong and mask fixation while allowing for normal infant movement. F&P Bubble CPAP System models include: BC151 connects to other infant CPAP interfaces (e.g. Hudson and Inca prongs) BC161 connects to the F&P Infant Interface BC171 connects to the M672P Infant Flow Driver (IFD) or equivalent BC161 BC171 BC Safe and Reliable Used on over a quarter of a million patients globally The unique auto-level mechanism of the Bubble CPAP generator provides consistent and accurate delivery of CPAP The pressure manifold with pressure relief valve promotes infant safety Easy to Use Easy auto-leveling by simply adding water into the Fill Funnel on the Bubble CPAP generator Excess condensate automatically drains into the detachable overflow container (see image on right) Detachable overflow container can be emptied without interrupting CPAP Optimum Humidification The F&P Bubble CPAP System provides respiratory support with body-temperature pressure-saturated gases to the infant Optimal humidity promotes mucociliary clearance and reduces the work of breathing Simple Yet Versatile Adjustable CPAP from 3 to 10 cmh 2 O The Bubble CPAP System can connect to various interfaces

33 FOCUS ON FEATURES Bubble CPAP Circuit Spiral heater-wire provides even heat distribution, reducing heat loss and condensate build-up Aims to deliver optimal humidity Bubble CPAP Pressure Manifold Limits the pressure delivered in the event of an occlusion Allows connection to a pressuremonitoring device and/or an air/oxygen analyzer MR290 Humidification Chamber Auto-fill, easy to use Maintains constant CPAP Closed system minimizes the risk of infection Bubble CPAP Generator Adjustable CPAP from 3 to 10 cmh2o Detachable overflow container allows uninterrupted CPAP when overflow container is being emptied Includes separate Fill Funnel Mounting bracket is incorporated on the back of the Bubble CPAP generator

34 F&P Bubble CPAP System SPECIFICATIONS F&P Bubble CPAP System Input Flow Range Recommended Input Flow Set CPAP Pressure Range Intended Patient Population Operating Temperature Range Storage Temperature Range Usage Period Maximum Pressure Limit Oxygen Analyzer Port 4 to 15 L/min 6 to 8 L/min 3 to 10 cmh 2 O Premature neonates and infants up to 10 kg 18 to 26 o C -10 to 50 o C Single patient use, for a maximum of 7 days 17 cmh 2 8 L/min 22 mm Male or 15 mm Female Pressure Monitoring Port Respiratory Humidifier Female luer F&P MR850 or MR730 only (Invasive Mode) Circuit Length Inspiratory Tube Expiratory Tube BC m (3.61 ft) 1.2 m (3.94 ft) BC m (4.59 ft) includes 300 mm (11.8 in) extension to connect to Hudson Prongs 1.2 m (3.94 ft) BC m (3.61 ft) 1.2 m (3.94 ft) F&P Bubble cpap system models Product Code & Description BC151* BC161* EN Rev B 2012 Fisher & Paykel Healthcare Limited BC171* * Box of 10 Note: For ordering information, please refer to the Fisher &Paykel Healthcare Bubble CPAP Product Catalogue (Part No ). MR850 Humidifier must be purchased separately. Manufacturer Fisher & Paykel Healthcare Ltd, 15 Maurice Paykel Place, East Tamaki, Auckland 2013, PO Box , Panmure, Auckland 1741, New Zealand Tel: Fax: info@fphcare.co.nz Web: Australia Tel: Fax: Austria Tel: Fax: Benelux Tel: Fax: China Tel: Fax: France Tel: Fax: Germany Tel: Fax: India Tel: Fax: Irish Republic Tel: Italy Tel: Fax: Japan Tel: Fax: Northern Ireland Tel: Spain Tel: Fax: Sweden Tel: Fax: Switzerland Tel: Fax: Taiwan Tel: Fax: Turkey Tel: Fax: UK (EU Authorised Representative) Fisher & Paykel Healthcare Ltd, Unit 16, Cordwallis Park, Clivemont Road, Maidenhead, Berkshire SL6 7BU, UK Tel: Fax: USA Tel: or Fax: