M54HCxxx M54HCTxxx. Rad-hard high speed 2 to 6 V CMOS logic series. Features. Description
|
|
|
- Esther Williams
- 7 years ago
- Views:
Transcription
1 M54HCxxx M54HCTxxx Rad-hard high speed 2 to 6 V CMOS logic series Features 2 to 6 V operating voltage Low power DC dissipation: 1 µa max at 25 C High speed T PD = 8 ns typ at 25 C Symmetrical outputs characteristics High noise immunity: 28% of min V CC Hermetic packages Rad-hard 50 krad (Si) SEL immune up to 110 MeV/mg/cm² ESCC qualified Same die and electrical specification for engineering and flight models The complete specification of each type is available from the ESCC web site: using its ESCC part number. ST guarantees full compliance of qualified parts with these ESCC specifications Description The M54HCxxx and M54HCTxxx series are composed of over 90 types of high speed CMOS functions specifically designed to meet the radiation requirements of the aerospace industry. It includes a large set of gates, Flip-Flops, Multiplexers, Counters, Bus Interface and several other functions. The radiation hardness, the single event latch-up (SEL) immunity and the housing in hermetic packages of all types of both series make them ideally suited for use in the most difficult environmental conditions. Flat-14 Flat-16 Flat-20 Flat-24 DIL-24 April 2010 Doc ID Rev 1 1/
2 Contents M54HCxxx - M54HCTxxx Contents 1 M54HC and M54HCT families overview Input equivalent circuit diagram Maximum rating Absolute maximum ratings M54HC series M54HCT series Recommended operating conditions M54HC series M54HCT series Radiation data Package mechanical data Order codes Revision history /29 Doc ID Rev 1
3 3/29 Doc ID Rev 1 1 M54HC and M54HCT families overview Table 1. Part number M54HC00 Device summary Description Rad-hard quad 2-input NAND gate Radiation level Agency qualification EPPL ESCC Vcc specification Package Vin Min Max range M54HC02 Rad-hard quad 2-input NOR gate Y 9201/ krad Rad-hard quad 2-input NAND open (Si) M54HC03 Y 9201/114 drain ESCC Y 9201/105 M54HC04 Rad-hard Hex inverter Y 9401/033 M54HCU04 Rad-hard Hex inverter single stage /055 M54HC08 Rad-hard quad 2-input AND gate Y 9201/106 M54HC10 Rad-hard triple 3-input NAND gate Y 9201/107 M54HC11 Rad-hard triple 3-input AND gate Y 9201/ krad M54HC14 Rad-hard Hex Schmitt inverter Y 9409/007 (Si) M54HC20 Rad-hard dual 4-input NAND gate Y 9201/118 M54HC21 Rad-hard dual 4-input AND gate Y 9201/108 M54HC27 Rad-hard triple 3-input NOR gate Y 9201/ to Vcc Other features Unbuffered output Temp. range -55 C to 125 C M54HC and M54HCT families overview M54HCxxx - M54HCTxxx
4 Doc ID Rev 1 4/29 Table 1. Part number M54HC30 Rad-hard 8-input NAND gate /110 M54HC32 Rad-hard quad 2-input OR gate Y 9201/111 M54HC73 Rad-hard dual J-K flip-flop with clear /071 M54HC74 M54HCT74 Rad-hard dual D-Type Flip-Flop with preset & clear Rad-hard dual D-Type Flip-Flop with preset & clear Y 9203/050 Y 9203/070 M54HC75 Rad-hard 4-bit D-type latch / krad ESCC Rad-hard 4-bit magnitude (Si) M54HC85 Y 9209/004 comparator M54HC86 Rad-hard quad exclusive OR gate Y 9201/119 M54HC109 M54HC123 Rad-hard dual J-K Flip-Flop with preset & clear Rad-hard dual retrigg. monostable multivibrator with clear Y 9306/ / to Vcc Negativeedge Positiveedge Positiveedge TTL compatible Pinout 1 M54HC125 Rad-hard quad bus buffer 3-state Y 9401/039 Flat-14 M54HC132 M54HC137 Device summary (continued) Description Rad-hard quad 2-input Schmitt NAND gate Rad-hard 3-to-8 line decoder latch inverter Radiation level Agency qualification EPPL ESCC Vcc specification Package Vin Min Max range Y 9201/ /013 Other features Positiveedge Inverted enables Temp. range -55 C to 125 C M54HCxxx - M54HCTxxx M54HC and M54HCT families overview
5 5/29 Doc ID Rev 1 Table 1. Part number M54HC138 M54HC139 Rad-hard 3-to-8 line decoder inverter Rad-hard dual 2-to-4 line decoder/demultiplexer Y 9408/046 Y 9205/017 M54HC148 Rad-hard 8-to-3 line priority encoder /017 M54HC151 Rad-hard 8-channel multiplexer Y 9408/054 M54HC153 Rad-hard dual 4-channel multiplexer /038 M54HC154 M54HC157 Rad-hard quad 2-channel multiplexer Y 9408/ krad ESCC Rad-hard quad 2-channel multiplexer (Si) M54HC158 Y 9408/059 Inverter M54HC160 M54HC161 M54HC163 Rad-hard 4-to-16 line decoder/demultiplexer Rad-hard synchronous decade counter with async. clear Rad-hard synchronous binary counter with async. clear Rad-hard synchronous binary counter with sync. clear Y 9205/023 Flat-24 - DIL /062 Y 9204/059 Y 9204/073 M54HC164 Rad-hard 8-bit SIPO shift register Y 9306/041 M54HC165 Rad-hard 8-bit PISO shift register Y 9306/042 M54HC166 Device summary (continued) Description Rad-hard 8-bit PISO shift register with clear Radiation level Agency qualification EPPL ESCC Vcc specification Package Vin Min Max range Y 9306/043 0 to Vcc Other features Temp. range -55 C to 125 C M54HC and M54HCT families overview M54HCxxx - M54HCTxxx
6 Doc ID Rev 1 6/29 Table 1. Part number M54HC174 M54HC175 M54HC191 M54HC193 Rad-hard Hex D-Type Flip-Flop with clear Rad-Hard Quad D-Type Flip-Flop With Clear Rad-Hard 4-bit synchronous binary up/down counter Rad-hard synchronous up/down binary counter Y 9306/052 Y 9203/052 Y 9204/066 Y 9204/065 M54HC194 Rad-hard 4-bit PIPO shit register /047 M54HC237 Rad-hard 3-to-8 line decoder latch Y 9205/021 M54HC238 Rad-hard 3-to-8 line decoder Y 9205/ krad ESCC (Si) Rad-hard octal bus buffer 3-state M54HC240 Y 9401/034 inverter M54HCT240 Device summary (continued) Description Rad-hard octal bus buffer 3-state inverter Radiation level Agency qualification EPPL ESCC Vcc specification Package Vin Min Max range Y 9401/045 M54HC241 Rad-hard octal bus buffer 3-state /035 M54HC244 Rad-hard octal bus buffer 3-state Y 9401/048 M54HCT244 Rad-hard octal bus buffer 3-state Y 9402/ to Vcc Other features 4 Shift Modes Independe nt enables TTL compatible Compleme ntary enables Inverted enables Inverted enables TTL compatible Temp. range -55 C to 125 C M54HCxxx - M54HCTxxx M54HC and M54HCT families overview
7 7/29 Doc ID Rev 1 Table 1. Part number M54HC245 M54HCT245 M54HC251 M54HC253 M54HC257 Rad-hard octal bus transceiver 3- state Rad-hard octal bus transceiver 3- state Rad-hard 8-channel multiplexer 3- state Rad-hard dual 4-channel multiplexer 3-state Rad-hard quad 2-channel multiplexer 3-state Y 9405/013 Y 9405/ / /058 M54HC259 Rad-hard 8-bit adressable latch /073 Rad-hard octal d-type flip-flop with M54HC273 Y 9203/053 clear 50 krad ESCC (Si) M54HC283 Rad-hard 4-bit binary full adder Y 9202/075 M54HC365 Rad-hard Hex bus buffer 3-state /052 M54HC367 Rad-hard Hex bus buffer 3-state /044 M54HC373 Rad-hard octal D-Type latch 3-state Y 9203/059 M54HCT373 Rad-hard octal D-Type latch 3-state Y 9203/064 M54HC374 M54HCT374 Device summary (continued) Description Rad-hard octal D-Type Flip-Flop 3- state Rad-hard octal D-Type Flip-Flop 3- state Radiation level Agency qualification EPPL ESCC Vcc specification Package Vin Min Max range Y 9408/047 Flat-16 Y 9203/060 Y 9203/ to Vcc Other features TTL compatible Independe nt enables TTL compatible TTL compatible Temp. range -55 C to 125 C M54HC and M54HCT families overview M54HCxxx - M54HCTxxx
8 Doc ID Rev 1 8/29 Table 1. Part number M54HC390 Rad-hard dual decade counter 50 krad (Si) ESCC /078 M54HC393 Rad-hard dual binary counter /074 M54HC540 Rad-hard octal bus buffer 3-state inverter Y 9401/049 M54HC541 Rad-hard octal bus buffer 3-state Y 9401/047 M54HC573 Rad-hard octal D-Type latch 3-state Y 9202/072 M54HC574 M54HC590 M54HC595 Rad-hard octal D-Type Flip-Flop 3- state Rad-hard 8 bit binary counter register 3-state Rad-hard 8 bit shift register output latch 3-state Y 9203/054 Y 9204/071 Y 9306/051 M54HC597 Rad-hard 8 bit latch/shift register Y 9306/054 M54HC688 Rad-hard 8 bit equality comparator Y 9209/005 M54HC4002 Rad-hard dual 4-input NOR gate /130 M54HC4020 Rad-hard 14-stage binary counter /070 M54HC4040 Rad-hard 12-stage binary counter Y 9204/069 M54HC4049 Device summary (continued) Description Rad-hard hex buffer/converter inverter Radiation level Agency qualification EPPL ESCC Vcc specification Package Vin Min Max range Y 9401/037 0 to Vcc Other features Non Inverted Enables Through Chip Pinout Through Chip Pinout Temp. range -55 C to 125 C M54HCxxx - M54HCTxxx M54HC and M54HCT families overview
9 9/29 Doc ID Rev 1 Table 1. Part number M54HC4050 M54HC4051 M54HC4053 M54HC4060 Note: Rad-hard hex buffer/converter Rad-hard single 8-channel analog mux/demux Rad-hard triple 2-channel analog mux/demux Rad-hard 14-stage binary counter/oscillator Y 9401/ / / /076 M54HC4066 Rad-hard quad bilateral switch / krad ESCC (Si) M54HC4072 Rad-hard dual 4-input OR gate /124 M54HC4075 Rad-hard triple 3-input OR gate /129 M54HC4078 Rad-hard 8-input NOR/OR gate /123 M54HC4094 Device summary (continued) Description Rad-hard 8-bit SIPO shit register 3- state Radiation level Agency qualification EPPL ESCC Vcc specification Package Vin Min Max range /050 M54HC4514 Rad-hard 4-to-16 line decoder latch /019 Flat-24 - DIL-24 Contact ST sales office for information about the specific conditions for other 54AC or 54ACT part number, product in die form and QML-Q versions 0 to Vcc Other features Temp. range -55 C to 125 C M54HC and M54HCT families overview M54HCxxx - M54HCTxxx
10 Input equivalent circuit diagram M54HCxxx - M54HCTxxx 2 Input equivalent circuit diagram Figure 1. Input equivalent circuit diagram 10/29 Doc ID Rev 1
11 M54HCxxx - M54HCTxxx Maximum rating 3 Maximum rating 3.1 Absolute maximum ratings M54HC series Table 2. Absolute maximum ratings - M54HC series Symbol Parameter Value Unit V CC Supply voltage -0.5 to +7 V V I DC input voltage -0.5 to VCC +0.5 V V O DC output voltage -0.5 to VCC +0.5 V I IK DC input diode current ± 20 ma I OK DC output diode current ± 20 ma I O DC output current ± 25 ma I CC or I GND DC V CC or ground current ± 50 ma P D Power dissipation 300 mw T stg Storage temperature -65 to +150 C T L Lead temperature (10 sec) 265 C Note: All voltage values are referred to V SS pin voltage M54HCT series Table 3. Absolute maximum ratings - M54HCT series Symbol Parameter Value Unit V CC Supply voltage -0.5 to +7 V V I DC input voltage -0.5 to V CC +0.5 V V O DC output voltage -0.5 to V CC +0.5 V I IK DC input diode current ± 20 ma I OK DC output diode current ± 20 ma I O DC output current ± 35 ma I CC or I GND DC V CC or ground current ± 70 ma P D Power dissipation 420 mw T stg Storage temperature -65 to +150 C T L Lead temperature (10 sec) 265 C Note: All voltage values are referred to V SS pin voltage. Doc ID Rev 1 11/29
12 Maximum rating M54HCxxx - M54HCTxxx 3.2 Recommended operating conditions M54HC series Table 4. Recommended operating conditions Symbol Parameter Value Unit V CC Supply voltage 2 to 6 V V I Input voltage 0 to V CC V V O Output voltage 0 to V CC V T op Operating temperature -55 to 125 C M54HCT series Table 5. Recommended operating conditions Symbol Parameter Value Unit V CC Supply voltage 4.5 to 5.5 V V I Input voltage 0 to VCC V V O Output voltage 0 to VCC V T op Operating temperature -55 to 125 C t r,t f Input rise and fall time (VCC = 4.5 to 5.5V) 0 to 500 ns 12/29 Doc ID Rev 1
13 M54HCxxx - M54HCTxxx Radiation data 4 Radiation data Each wafer lot is qualified at 50 krad (Si) total dose as per ESCC specification at 210 rad/hour. The HC/HCT series is characterized under heavy Ion on 4 functions representative of the whole series and qualified as per the results of this characterization. Detailed results are provided in the table below: Table 6. Radiation data Function Result Gate: 54HC08 Multiplexer 54HC157 Flip-flop 54HC273 Counter 54HC4040 Analog Mux/Demux 54HC4053 SEL and SEU free for LET [ 111 MeV/mg/cm² SEL and SEU free for LET[ 111 MeV/mg/cm² SEL free for LET [ 111 MeV/mg/cm² SEU: LET th = 16MeV/mg/cm², σsat = 1.7x10-4 cm² SEL free for LET [ 111 MeV/mg/cm² SEU: LET th = 34MeV/mg/cm², σsat = 4.2x10-4 cm² SEL free for LET [ 111 MeV/mg/cm² SEU: LET th = 7MeV/mg/cm², σsat = 2.4x10-4 cm² Doc ID Rev 1 13/29
14 Package mechanical data M54HCxxx - M54HCTxxx 5 Package mechanical data In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK packages, depending on their level of environmental compliance. ECOPACK specifications, grade definitions and product status are available at: ECOPACK is an ST trademark. Table 7. Ceramic Flat-14 mechanical data mm Dim Min Typ Max A B C D E F 1.27 G H 6.0 L en 22.0 M 0.38 N 4.31 Figure 2. Ceramic Flat-14 mechanical drawings F G D H 14 8 A N L 1 7 H E M B C E 14/29 Doc ID Rev 1
15 M54HCxxx - M54HCTxxx Package mechanical data Table 8. Ceramic mechanical data Mm. Dim. Min. Typ Max. A a a B b b D E e 2.54 e e F I 3.70 K n L Figure 3. Ceramic mechanical drawings H Doc ID Rev 1 15/29
16 Package mechanical data M54HCxxx - M54HCTxxx Table 9. Ceramic Flat-16 mechanical data Mm. Dim. Min. Typ Max. A B C D E F 1.27 G H 6.0 L en 22.0 M N 4.31 Figure 4. Ceramic Flat-16 mechanical drawings F G D H 16 9 A N L 1 8 H E M B C E 16/29 Doc ID Rev 1
17 M54HCxxx - M54HCTxxx Package mechanical data Table 10. Ceramic package dimensions mm Dim Min Typ Max A a a B b b D E e 2.54 e e F I 3.83 K L Figure 5. Ceramic package drawings Doc ID Rev 1 17/29
18 Package mechanical data M54HCxxx - M54HCTxxx Table 11. Ceramic Flat-24 package dimensions mm Dim Min Typ Max A B C D E F G H L M N 7.01 Figure 6. Ceramic Flat-24 package drawings 18/29 Doc ID Rev 1
19 M54HCxxx - M54HCTxxx Package mechanical data Table 12. Ceramic DIL-24 package dimensions mm Dim Min Typ Max A a a B b b C D E e e F K K L Figure 7. Ceramic DIL-24 package drawings Doc ID Rev 1 19/29
20 Doc ID Rev 1 20/29 6 Order codes Table 13. Ordering information Order codes ESCC detailed Quality Mass Comment Package Lead finish Marking specification Level (g) EPPL Packing M54HC00K 9201/105/01F or 02F ESCC flight Specify ESCC variant number in PO Flat-14 Gold or solder dip F or 02F 0.70 Y Strip pack M54HC00D 9201/105/03F or 04F ESCC flight Specify ESCC variant number in PO Gold or solder dip F or 04F Strip pack M54HC02K 9201/113/01F or 02F ESCC flight Specify ESCC variant number in PO Flat-14 Gold or solder dip F or 02F 0.70 Y Strip pack M54HC02D 9201/113/03F or 04F ESCC flight Specify ESCC variant number in PO Gold or solder dip F or 04F Strip pack M54HC03K 9201/114/01F or 02F ESCC flight Specify ESCC variant number in PO Flat-14 Gold or solder dip F or 02F 0.70 Y Strip pack M54HC03D 9201/114/03F or 04F ESCC flight Specify ESCC variant number in PO Gold or solder dip F or 04F Strip pack M54HC04K 9401/033/01F or 02F ESCC flight Specify ESCC variant number in PO Flat-14 Gold or solder dip F or 02F 0.70 Y Strip pack M54HC04D 9401/033/03F or 04F ESCC flight Specify ESCC variant number in PO Gold or solder dip F or 04F Strip pack M54HCU04K 9401/055/01F or 02F ESCC flight Specify ESCC variant number in PO Flat-14 Gold or solder dip F or 02F Strip pack M54HCU04D 9401/055/03F or 04F ESCC flight Specify ESCC variant number in PO Gold or solder dip F or 04F Strip pack M54HC08K 9201/106/01F or 02F ESCC flight Specify ESCC variant number in PO Flat-14 Gold or solder dip F or 02F 0.70 Y Strip pack M54HC08D 9201/106/03F or 04F ESCC flight Specify ESCC variant number in PO Gold or solder dip F or 04F Strip pack M54HC10K 9201/107/01F or 02F ESCC flight Specify ESCC variant number in PO Flat-14 Gold or solder dip F or 02F 0.70 Y Strip pack M54HC10D 9201/107/03F or 04F ESCC flight Specify ESCC variant number in PO Gold or solder dip F or 04F Strip pack M54HC11K 9201/117/01F or 02F ESCC flight Specify ESCC variant number in PO Flat-14 Gold or solder dip F or 02F 0.70 Y Strip pack M54HC11D 9201/117/03F or 04F ESCC flight Specify ESCC variant number in PO Gold or solder dip F or 04F Strip pack M54HC14K 9409/007/01F or 02F ESCC flight Specify ESCC variant number in PO Flat-14 Gold or solder dip F or 02F 0.70 Y Strip pack M54HC14D 9409/007/03F or 04F ESCC flight Specify ESCC variant number in PO Gold or solder dip F or 04F Strip pack M54HC20K 9201/118/01F or 02F ESCC flight Specify ESCC variant number in PO Flat-14 Gold or solder dip F or 02F 0.70 Y Strip pack M54HC20D 9201/118/03F or 04F ESCC flight Specify ESCC variant number in PO Gold or solder dip F or 04F Strip pack M54HC21K 9201/108/01F or 02F ESCC flight Specify ESCC variant number in PO Flat-14 Gold or solder dip F or 02F 0.70 Y Strip pack M54HC21D 9201/108/03F or 04F ESCC flight Specify ESCC variant number in PO Gold or solder dip F or 04F Strip pack M54HCxxx - M54HCTxxx Order codes
21 21/29 Doc ID Rev 1 Table 13. Ordering information (continued) Order codes ESCC detailed Quality Mass Comment Package Lead finish Marking specification Level (g) EPPL Packing M54HC27K 9201/109/01F or 02F ESCC flight Specify ESCC variant number in PO Flat-14 Gold or solder dip F or 02F 0.70 Y Strip pack M54HC27D 9201/109/03F or 04F ESCC flight Specify ESCC variant number in PO Gold or solder dip F or 04F Strip pack M54HC30K 9201/110/01F or 02F ESCC flight Specify ESCC variant number in PO Flat-14 Gold or solder dip F or 02F Strip pack M54HC30D 9201/110/03F or 04F ESCC flight Specify ESCC variant number in PO Gold or solder dip F or 04F Strip pack M54HC32K 9201/111/01F or 02F ESCC flight Specify ESCC variant number in PO Flat-14 Gold or solder dip F or 02F 0.70 Y Strip pack M54HC32D 9201/111/03F or 04F ESCC flight Specify ESCC variant number in PO Gold or solder dip F or 04F Strip pack M54HC73K 9203/071/01F or 02F ESCC flight Specify ESCC variant number in PO Flat-14 Gold or solder dip F or 02F Strip pack M54HC73D 9203/071/03F or 04F ESCC flight Specify ESCC variant number in PO Gold or solder dip F or 04F Strip pack M54HC74K 9203/050/01F or 02F ESCC flight Specify ESCC variant number in PO Flat-14 Gold or solder dip F or 02F 0.70 Y Strip pack M54HC74D 9203/050/03F or 04F ESCC flight Specify ESCC variant number in PO Gold or solder dip F or 04F Strip pack M54HCT74K 9203/070/01F or 02F ESCC flight Specify ESCC variant number in PO Flat-14 Gold or solder dip F or 02F 0.70 Y Strip pack M54HCT74D 9203/070/03F or 04F ESCC flight Specify ESCC variant number in PO Gold or solder dip F or 04F Strip pack M54HC75K 9203/065/01F or 02F ESCC flight Specify ESCC variant number in PO Flat-16 Gold or solder dip F or 02F Strip pack M54HC75D 9203/065/10F or 11F ESCC flight Specify ESCC variant number in PO Gold or solder dip F or 11F Strip pack M54HC85K 9209/004/01F or 02F ESCC flight Specify ESCC variant number in PO Flat-16 Gold or solder dip F or 02F 0.70 Y Strip pack M54HC85D 9209/004/10F or 11F ESCC flight Specify ESCC variant number in PO Gold or solder dip F or 11F Strip pack M54HC86K 9201/119/01F or 02F ESCC flight Specify ESCC variant number in PO Flat-14 Gold or solder dip F or 02F 0.70 Y Strip pack M54HC86D 9201/119/03F or 04F ESCC flight Specify ESCC variant number in PO Gold or solder dip F or 04F Strip pack M54HC109K 9306/048/01F or 02F ESCC flight Specify ESCC variant number in PO Flat-16 Gold or solder dip F or 02F 0.70 Y Strip pack M54HC109D 9306/048/10F or 11F ESCC flight Specify ESCC variant number in PO Gold or solder dip F or 11F Strip pack M54HC123K 9207/006/01F or 02F ESCC flight Specify ESCC variant number in PO Flat-16 Gold or solder dip F or 02F Strip pack M54HC123D 9207/006/10F or 11F ESCC flight Specify ESCC variant number in PO Gold or solder dip F or 11F Strip pack M54HC125K 9401/039/01F or 02F ESCC flight Specify ESCC variant number in PO Flat-14 Gold or solder dip F or 02F 0.70 Y Strip pack M54HC132K 9201/120/01F or 02F ESCC flight Specify ESCC variant number in PO Flat-14 Gold or solder dip F or 02F 0.70 Y Strip pack M54HC132D 9201/120/03F or 04F ESCC flight Specify ESCC variant number in PO Gold or solder dip F or 04F Strip pack Order codes M54HCxxx - M54HCTxxx
22 Doc ID Rev 1 22/29 Table 13. Ordering information (continued) Order codes ESCC detailed Quality Mass Comment Package Lead finish Marking specification Level (g) EPPL Packing M54HC137K 9205/013/01F or 02F ESCC flight Specify ESCC variant number in PO Flat-16 Gold or solder dip F or 02F Strip pack M54HC137D 9205/013/10F or 11F ESCC flight Specify ESCC variant number in PO Gold or solder dip F or 11F Strip pack M54HC138K 9408/046/01F or 02F ESCC flight Specify ESCC variant number in PO Flat-16 Gold or solder dip F or 02F 0.70 Y Strip pack M54HC138D 9408/046/10F or 11F ESCC flight Specify ESCC variant number in PO Gold or solder dip F or 11F Strip pack M54HC139K 9205/017/01F or 02F ESCC flight Specify ESCC variant number in PO Flat-16 Gold or solder dip F or 02F 0.70 Y Strip pack M54HC139D 9205/017/10F or 11F ESCC flight Specify ESCC variant number in PO Gold or solder dip F or 11F Strip pack M54HC148K 9410/017/01F or 02F ESCC flight Specify ESCC variant number in PO Flat-16 Gold or solder dip F or 02F Strip pack M54HC148D 9410/017/10F or 11F ESCC flight Specify ESCC variant number in PO Gold or solder dip F or 11F Strip pack M54HC151K 9408/054/01F or 02F ESCC flight Specify ESCC variant number in PO Flat-16 Gold or solder dip F or 02F 0.70 Y Strip pack M54HC151D 9408/054/10F or 11F ESCC flight Specify ESCC variant number in PO Gold or solder dip F or 11F Strip pack M54HC153K 9408/038/01F or 02F ESCC flight Specify ESCC variant number in PO Flat-16 Gold or solder dip F or 02F Strip pack M54HC153D 9408/038/10F or 11F ESCC flight Specify ESCC variant number in PO Gold or solder dip F or 11F Strip pack M54HC154K 9205/023/01F or 02F ESCC flight Specify ESCC variant number in PO Flat-24 Gold or solder dip F or 02F 1.70 Y Strip pack M54HC154D 9205/023/03F or 04F ESCC flight Specify ESCC variant number in PO DIL-24 Gold or solder dip F or 04F Strip pack M54HC157K 9408/057/01F or 02F ESCC flight Specify ESCC variant number in PO Flat-16 Gold or solder dip F or 02F 0.70 Y Strip pack M54HC157D 9408/057/10F or 11F ESCC flight Specify ESCC variant number in PO Gold or solder dip F or 11F Strip pack M54HC158K 9408/059/01F or 02F ESCC flight Specify ESCC variant number in PO Flat-16 Gold or solder dip F or 02F 0.70 Y Strip pack M54HC158D 9408/059/10F or 11F ESCC flight Specify ESCC variant number in PO Gold or solder dip F or 11F Strip pack M54HC160D 9204/062/10F or 11F ESCC flight Specify ESCC variant number in PO Gold or solder dip F or 11F Strip pack M54HC161K 9204/059/01F or 02F ESCC flight Specify ESCC variant number in PO Flat-16 Gold or solder dip F or 02F 0.70 Y Strip pack M54HC161D 9204/059/10F or 11F ESCC flight Specify ESCC variant number in PO Gold or solder dip F or 11F Strip pack M54HC163K 9204/073/01F or 02F ESCC flight Specify ESCC variant number in PO Flat-16 Gold or solder dip F or 02F 0.70 Y Strip pack M54HC163D 9204/073/10F or 11F ESCC flight Specify ESCC variant number in PO Gold or solder dip F or 11F Strip pack M54HC164K 9306/041/01F or 02F ESCC flight Specify ESCC variant number in PO Flat-14 Gold or solder dip F or 02F 0.70 Y Strip pack M54HC164D 9306/041/03F or 04F ESCC flight Specify ESCC variant number in PO Gold or solder dip F or 04F Strip pack M54HCxxx - M54HCTxxx Order codes
23 23/29 Doc ID Rev 1 Table 13. Ordering information (continued) Order codes ESCC detailed Quality Mass Comment Package Lead finish Marking specification Level (g) EPPL Packing M54HC165K 9306/042/01F or 02F ESCC flight Specify ESCC variant number in PO Flat-16 Gold or solder dip F or 02F 0.70 Y Strip pack M54HC165D 9306/042/10F or 11F ESCC flight Specify ESCC variant number in PO Gold or solder dip F or 11F Strip pack M54HC166K 9306/043/01F or 02F ESCC flight Specify ESCC variant number in PO Flat-16 Gold or solder dip F or 02F 0.70 Y Strip pack M54HC166D 9306/043/10F or 11F ESCC flight Specify ESCC variant number in PO Gold or solder dip F or 11F Strip pack M54HC174K 9306/052/01F or 02F ESCC flight Specify ESCC variant number in PO Flat-16 Gold or solder dip F or 02F 0.70 Y Strip pack M54HC174D 9306/052/10F or 11F ESCC flight Specify ESCC variant number in PO Gold or solder dip F or 11F Strip pack M54HC175K 9203/052/01F or 02F ESCC flight Specify ESCC variant number in PO Flat-16 Gold or solder dip F or 02F 0.70 Y Strip pack M54HC175D 9203/052/10F or 11F ESCC flight Specify ESCC variant number in PO Gold or solder dip F or 11F Strip pack M54HC191K 9204/066/01F or 02F ESCC flight Specify ESCC variant number in PO Flat-16 Gold or solder dip F or 02F 0.70 Y Strip pack M54HC191D 9204/066/10F or 11F ESCC flight Specify ESCC variant number in PO Gold or solder dip F or 11F Strip pack M54HC193K 9204/065/01F or 02F ESCC flight Specify ESCC variant number in PO Flat-16 Gold or solder dip F or 02F 0.70 Y Strip pack M54HC193D 9204/065/10F or 11F ESCC flight Specify ESCC variant number in PO Gold or solder dip F or 11F Strip pack M54HC194K 9306/047/01F or 02F ESCC flight Specify ESCC variant number in PO Flat-16 Gold or solder dip F or 02F Strip pack M54HC194D 9306/047/10F or 11F ESCC flight Specify ESCC variant number in PO Gold or solder dip F or 11F Strip pack M54HC237K 9205/021/01F or 02F ESCC flight Specify ESCC variant number in PO Flat-16 Gold or solder dip F or 02F 0.70 Y Strip pack M54HC237D 9205/021/10F or 11F ESCC flight Specify ESCC variant number in PO Gold or solder dip F or 11F Strip pack M54HC238K 9205/016/01F or 02F ESCC flight Specify ESCC variant number in PO Flat-16 Gold or solder dip F or 02F Strip pack M54HC238D 9205/016/10F or 11F ESCC flight Specify ESCC variant number in PO Gold or solder dip F or 11F Strip pack M54HC240K 9401/034/01F or 02F ESCC flight Specify ESCC variant number in PO Flat-20 Gold or solder dip F or 02F 0.90 Y Strip pack M54HC240D 9401/034/03F or 04F ESCC flight Specify ESCC variant number in PO Gold or solder dip F or 04F Strip pack M54HCT240K 9401/045/01F or 02F ESCC flight Specify ESCC variant number in PO Flat-20 Gold or solder dip F or 02F 0.90 Y Strip pack M54HCT240D 9401/045/03F or 04F ESCC flight Specify ESCC variant number in PO Gold or solder dip F or 04F Strip pack M54HC241K 9401/035/01F or 02F ESCC flight Specify ESCC variant number in PO Flat-20 Gold or solder dip F or 02F Strip pack M54HC241D 9401/035/03F or 04F ESCC flight Specify ESCC variant number in PO Gold or solder dip F or 04F Strip pack M54HC244K 9401/048/01F or 02F ESCC flight Specify ESCC variant number in PO Flat-20 Gold or solder dip F or 02F 0.90 Y Strip pack Order codes M54HCxxx - M54HCTxxx
24 Doc ID Rev 1 24/29 Table 13. Ordering information (continued) Order codes ESCC detailed Quality Mass Comment Package Lead finish Marking specification Level (g) EPPL Packing M54HC244D 9401/048/03F or 04F ESCC flight Specify ESCC variant number in PO Gold or solder dip F or 04F Strip pack M54HCT244K 9402/009/01F or 02F ESCC flight Specify ESCC variant number in PO Flat-20 Gold or solder dip F or 02F 0.90 Y Strip pack M54HCT244D 9402/009/03F or 04F ESCC flight Specify ESCC variant number in PO Gold or solder dip F or 04F Strip pack M54HC245K 9405/013/01F or 02F ESCC flight Specify ESCC variant number in PO Flat-20 Gold or solder dip F or 02F 0.90 Y Strip pack M54HC245D 9405/013/03F or 04F ESCC flight Specify ESCC variant number in PO Gold or solder dip F or 04F Strip pack M54HCT245K 9405/014/01F or 02F ESCC flight Specify ESCC variant number in PO Flat-20 Gold or solder dip F or 02F 0.90 Y Strip pack M54HCT245D 9405/014/03F or 04F ESCC flight Specify ESCC variant number in PO Gold or solder dip F or 04F Strip pack M54HC251K 9408/048/01F or 02F ESCC flight Specify ESCC variant number in PO Flat-16 Gold or solder dip F or 02F Strip pack M54HC251D 9408/048/10F or 11F ESCC flight Specify ESCC variant number in PO Gold or solder dip F or 11F Strip pack M54HC253K 9408/058/01F or 02F ESCC flight Specify ESCC variant number in PO Flat-16 Gold or solder dip F or 02F Strip pack M54HC253D 9408/058/10F or 11F ESCC flight Specify ESCC variant number in PO Gold or solder dip F or 11F Strip pack M54HC257K 9408/047/01F or 02F ESCC flight Specify ESCC variant number in PO Flat-16 Gold or solder dip F or 02F 0.70 Y Strip pack M54HC259K 9203/073/01F or 02F ESCC flight Specify ESCC variant number in PO Flat-16 Gold or solder dip F or 02F Strip pack M54HC259D 9203/073/10F or 11F ESCC flight Specify ESCC variant number in PO Gold or solder dip F or 11F Strip pack M54HC273K 9203/053/01F or 02F ESCC flight Specify ESCC variant number in PO Flat-20 Gold or solder dip F or 02F 0.90 Y Strip pack M54HC273D 9203/053/03F or 04F ESCC flight Specify ESCC variant number in PO Gold or solder dip F or 04F Strip pack M54HC283K 9202/075/01F or 02F ESCC flight Specify ESCC variant number in PO Flat-16 Gold or solder dip F or 02F 0.70 Y Strip pack M54HC283D 9202/075/10F or 11F ESCC flight Specify ESCC variant number in PO Gold or solder dip F or 11F Strip pack M54HC365K 9401/052/01F or 02F ESCC flight Specify ESCC variant number in PO Flat-16 Gold or solder dip F or 02F Strip pack M54HC365D 9401/052/10F or 11F ESCC flight Specify ESCC variant number in PO Gold or solder dip F or 11F Strip pack M54HC367K 9401/044/01F or 02F ESCC flight Specify ESCC variant number in PO Flat-16 Gold or solder dip F or 02F Strip pack M54HC367D 9401/044/10F or 11F ESCC flight Specify ESCC variant number in PO Gold or solder dip F or 11F Strip pack M54HC373K 9203/059/01F or 02F ESCC flight Specify ESCC variant number in PO Flat-20 Gold or solder dip F or 02F 0.90 Y Strip pack M54HC373D 9203/059/03F or 04F ESCC flight Specify ESCC variant number in PO Gold or solder dip F or 04F Strip pack M54HCT373K 9203/064/01F or 02F ESCC flight Specify ESCC variant number in PO Flat-20 Gold or solder dip F or 02F 0.90 Y Strip pack M54HCxxx - M54HCTxxx Order codes
25 25/29 Doc ID Rev 1 Table 13. Ordering information (continued) Order codes ESCC detailed Quality Mass Comment Package Lead finish Marking specification Level (g) EPPL Packing M54HCT373D 9203/064/03F or 04F ESCC flight Specify ESCC variant number in PO Gold or solder dip F or 04F Strip pack M54HC374K 9203/060/01F or 02F ESCC flight Specify ESCC variant number in PO Flat-20 Gold or solder dip F or 02F 0.90 Y Strip pack M54HC374D 9203/060/03F or 04F ESCC flight Specify ESCC variant number in PO Gold or solder dip F or 04F Strip pack M54HCT374K 9203/066/01F or 02F ESCC flight Specify ESCC variant number in PO Flat-20 Gold or solder dip F or 02F 0.90 Y Strip pack M54HCT374D 9203/066/03F or 04F ESCC flight Specify ESCC variant number in PO Gold or solder dip F or 04F Strip pack M54HC390K 9204/078/01F or 02F ESCC flight Specify ESCC variant number in PO Flat-16 Gold or solder dip F or 02F Strip pack M54HC390D 9204/078/10F or 11F ESCC flight Specify ESCC variant number in PO Gold or solder dip F or 11F Strip pack M54HC393K 9204/074/01F or 02F ESCC flight Specify ESCC variant number in PO Flat-14 Gold or solder dip F or 02F Strip pack M54HC393D 9204/074/03F or 04F ESCC flight Specify ESCC variant number in PO Gold or solder dip F or 04F Strip pack M54HC540K 9401/049/01F or 02F ESCC flight Specify ESCC variant number in PO Flat-20 Gold or solder dip F or 02F 0.90 Y Strip pack M54HC540D 9401/049/03F or 04F ESCC flight Specify ESCC variant number in PO Gold or solder dip F or 04F Strip pack M54HC541K 9401/047/01F or 02F ESCC flight Specify ESCC variant number in PO Flat-20 Gold or solder dip F or 02F 0.90 Y Strip pack M54HC541D 9401/047/03F or 04F ESCC flight Specify ESCC variant number in PO Gold or solder dip F or 04F Strip pack M54HC573K 9202/072/01F or 02F ESCC flight Specify ESCC variant number in PO Flat-20 Gold or solder dip F or 02F 0.90 Y Strip pack M54HC573D 9202/072/03F or 04F ESCC flight Specify ESCC variant number in PO Gold or solder dip F or 04F Strip pack M54HC574K 9203/054/01F or 02F ESCC flight Specify ESCC variant number in PO Flat-20 Gold or solder dip F or 02F 0.90 Y Strip pack M54HC574D 9203/054/03F or 04F ESCC flight Specify ESCC variant number in PO Gold or solder dip F or 04F Strip pack M54HC590K 9204/071/01F or 02F ESCC flight Specify ESCC variant number in PO Flat-16 Gold or solder dip F or 02F 0.70 Y Strip pack M54HC590D 9204/071/10F or 11F ESCC flight Specify ESCC variant number in PO Gold or solder dip F or 11F Strip pack M54HC595K 9306/051/01F or 02F ESCC flight Specify ESCC variant number in PO Flat-16 Gold or solder dip F or 02F 0.70 Y Strip pack M54HC595D 9306/051/10F or 11F ESCC flight Specify ESCC variant number in PO Gold or solder dip F or 11F Strip pack M54HC597K 9306/054/01F or 02F ESCC flight Specify ESCC variant number in PO Flat-16 Gold or solder dip F or 02F 0.70 Y Strip pack M54HC597D 9306/054/10F or 11F ESCC flight Specify ESCC variant number in PO Gold or solder dip F or 11F Strip pack M54HC688K 9209/005/01F or 02F ESCC flight Specify ESCC variant number in PO Flat-20 Gold or solder dip F or 02F 0.90 Y Strip pack M54HC688D 9209/005/03F or 04F ESCC flight Specify ESCC variant number in PO Gold or solder dip F or 04F Strip pack Order codes M54HCxxx - M54HCTxxx
26 Doc ID Rev 1 26/29 Table 13. Ordering information (continued) Order codes ESCC detailed Quality Mass Comment Package Lead finish Marking specification Level (g) EPPL Packing M54HC4002K 9201/130/01F or 02F ESCC flight Specify ESCC variant number in PO Flat-14 Gold or solder dip F or 02F Strip pack M54HC4002D 9201/130/03F or 04F ESCC flight Specify ESCC variant number in PO Gold or solder dip F or 04F Strip pack M54HC4020K 9204/070/01F or 02F ESCC flight Specify ESCC variant number in PO Flat-16 Gold or solder dip F or 02F Strip pack M54HC4020D 9204/070/10F or 11F ESCC flight Specify ESCC variant number in PO Gold or solder dip F or 11F Strip pack M54HC4040K 9204/069/01F or 02F ESCC flight Specify ESCC variant number in PO Flat-16 Gold or solder dip F or 02F 0.70 Y Strip pack M54HC4040D 9204/069/10F or 11F ESCC flight Specify ESCC variant number in PO Gold or solder dip F or 11F Strip pack M54HC4049K 9401/037/01F or 02F ESCC flight Specify ESCC variant number in PO Flat-16 Gold or solder dip F or 02F 0.70 Y Strip pack M54HC4049D 9401/037/10F or 11F ESCC flight Specify ESCC variant number in PO Gold or solder dip F or 11F Strip pack M54HC4050K 9401/038/01F or 02F ESCC flight Specify ESCC variant number in PO Flat-16 Gold or solder dip F or 02F 0.70 Y Strip pack M54HC4050D 9401/038/10F or 11F ESCC flight Specify ESCC variant number in PO Gold or solder dip F or 11F Strip pack M54HC4051K 9408/064/01F or 02F ESCC flight Specify ESCC variant number in PO Flat-16 Gold or solder dip F or 02F Strip pack M54HC4051D 9408/064/10F or 11F ESCC flight Specify ESCC variant number in PO Gold or solder dip F or 11F Strip pack M54HC4053K 9408/065/01F or 02F ESCC flight Specify ESCC variant number in PO Flat-16 Gold or solder dip F or 02F Strip pack M54HC4053D 9408/065/10F or 11F ESCC flight Specify ESCC variant number in PO Gold or solder dip F or 11F Strip pack M54HC4060K 9204/076/01F or 02F ESCC flight Specify ESCC variant number in PO Flat-16 Gold or solder dip F or 02F Strip pack M54HC4060D 9204/076/10F or 11F ESCC flight Specify ESCC variant number in PO Gold or solder dip F or 11F Strip pack M54HC4066K 9408/052/01F or 02F ESCC flight Specify ESCC variant number in PO Flat-14 Gold or solder dip F or 02F Strip pack M54HC4066D 9408/052/03F or 04F ESCC flight Specify ESCC variant number in PO Gold or solder dip F or 04F Strip pack M54HC4072K 9201/124/01F or 02F ESCC flight Specify ESCC variant number in PO Flat-14 Gold or solder dip F or 02F Strip pack M54HC4072D 9201/124/03F or 04F ESCC flight Specify ESCC variant number in PO Gold or solder dip F or 04F Strip pack M54HC4075K 9201/129/01F or 02F ESCC flight Specify ESCC variant number in PO Flat-14 Gold or solder dip F or 02F Strip pack M54HC4075D 9201/129/03F or 04F ESCC flight Specify ESCC variant number in PO Gold or solder dip F or 04F Strip pack M54HC4078K 9201/123/01F or 02F ESCC flight Specify ESCC variant number in PO Flat-14 Gold or solder dip F or 02F Strip pack M54HC4078D 9201/123/03F or 04F ESCC flight Specify ESCC variant number in PO Gold or solder dip F or 04F Strip pack M54HC4094K 9306/050/01F or 02F ESCC flight Specify ESCC variant number in PO Flat-16 Gold or solder dip F or 02F Strip pack M54HCxxx - M54HCTxxx Order codes
27 27/29 Doc ID Rev 1 Table 13. Order codes M54HC4094D 9306/050/10F or 11F ESCC flight Specify ESCC variant number in PO Gold or solder dip F or 11F Strip pack M54HC4514K 9205/019/01F or 02F ESCC flight Specify ESCC variant number in PO Flat-24 Gold or solder dip F or 02F Strip pack M54HC4514D 9205/019/03F or 04F ESCC flight Specify ESCC variant number in PO DIL-24 Gold or solder dip F or 04F Strip pack Note: Ordering information (continued) ESCC detailed specification Quality Level Comment Package Lead finish Marking Contact ST sales office for information about the specific conditions for other 54AC or 54ACT part number, product in die form and QML-Q versions Mass (g) EPPL Packing Order codes M54HCxxx - M54HCTxxx
28 Revision history M54HCxxx - M54HCTxxx 7 Revision history Table 14. Revision history Date Revision Changes 14-Apr First release 28/29 Doc ID Rev 1
29 M54HCxxx - M54HCTxxx Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries ( ST ) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan - Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America Doc ID Rev 1 29/29
ULN2801A, ULN2802A, ULN2803A, ULN2804A
ULN2801A, ULN2802A, ULN2803A, ULN2804A Eight Darlington array Datasheet production data Features Eight Darlington transistors with common emitters Output current to 500 ma Output voltage to 50 V Integral
DDSL01. Secondary protection for DSL lines. Features. Description
Secondary protection for DSL lines Features Stand off voltage: 30 V Surge capability: I pp = 30 A 8/20 µs Low capacitance device: 4.5 pf at 2 V RoHS package Low leakage current: 0.5 µa at 25 C 3 2 Description
BD238. Low voltage PNP power transistor. Features. Applications. Description. Low saturation voltage PNP transistor
Low voltage PNP power transistor Features Low saturation voltage PNP transistor Applications Audio, power linear and switching applications Description The device is manufactured in planar technology with
BD241A BD241C. NPN power transistors. Features. Applications. Description. NPN transistors. Audio, general purpose switching and amplifier transistors
BD241A BD241C NPN power transistors Features. NPN transistors Applications Audio, general purpose switching and amplifier transistors Description The devices are manufactured in Planar technology with
2STBN15D100. Low voltage NPN power Darlington transistor. Features. Application. Description
Low voltage NPN power Darlington transistor Features Good h FE linearity High f T frequency Monolithic Darlington configuration with integrated antiparallel collector-emitter diode TAB Application Linear
Description. Table 1. Device summary. Order code Temperature range Package Packaging Marking
14-stage ripple carry binary counter/divider and oscillator Applications Automotive Industrial Computer Consumer Description Datasheet - production data Features Medium speed operation Common reset Fully
ULN2001, ULN2002 ULN2003, ULN2004
ULN2001, ULN2002 ULN2003, ULN2004 Seven Darlington array Datasheet production data Features Seven Darlingtons per package Output current 500 ma per driver (600 ma peak) Output voltage 50 V Integrated suppression
ST13005. High voltage fast-switching NPN power transistor. Features. Applications. Description
High voltage fast-switching NPN power transistor Datasheet production data Features Low spread of dynamic parameters Minimum lot-to-lot spread for reliable operation Very high switching speed Applications
L6234. Three phase motor driver. Features. Description
Three phase motor driver Features Supply voltage from 7 to 52 V 5 A peak current R DSon 0.3 Ω typ. value at 25 C Cross conduction protection TTL compatible driver Operating frequency up to 150 khz Thermal
Order code Temperature range Package Packaging
ST485B ST485C Low power RS-485/RS-422 transceiver Features Low quiescent current: 300 µa Designed for RS-485 interface application - 7 V to 12 V common mode input voltage range Driver maintains high impedance
LM337. Three-terminal adjustable negative voltage regulators. Features. Description
Three-terminal adjustable negative voltage regulators Datasheet - production data current limit, thermal overload protection and safe area protection. All overload protection circuitry remains fully functional
EVL185W-LEDTV. 185 W power supply with PFC and standby supply for LED TV based on the L6564, L6599A and Viper27L. Features.
Features 185 W power supply with PFC and standby supply for LED TV based on the L6564, L6599A and Viper27L Data brief Universal input mains range: 90 264 Vac - frequency 45 65 Hz Output voltage 1: 130
TN0023 Technical note
Technical note Discontinuous flyback transformer description and design parameters Introduction The following is a general description and basic design procedure for a discontinuous flyback transformer.
LM134-LM234-LM334. Three terminal adjustable current sources. Features. Description
Three terminal adjustable current sources Features Operates from 1V to 40V 0.02%/V current regulation Programmable from 1µA to 10mA ±3% initial accuracy Description The LM134/LM234/LM334 are 3-terminal
ETP01-xx21. Protection for Ethernet lines. Features. Description. Applications. Benefits. Complies with the following standards
ETP0-xx2 Protection for Ethernet lines Features Differential and common mode protection Telcordia GR089 Intrabuilding: 50 A, 2/0 µs ITU-T K20/2: 40 A, 5/30 µs Low capacitance: 3 pf max at 0 V UL94 V0 approved
L78MxxAB L78MxxAC. Precision 500 ma regulators. Features. Description
L78MxxAB L78MxxAC Precision 500 ma regulators Features Output current to 0.5 A Output voltages of 5; 6; 8; 9; 10; 12; 15; 18; 24 V Thermal overload protection Short circuit protection Output transition
BD135 - BD136 BD139 - BD140
BD135 - BD136 BD139 - BD140 Complementary low voltage transistor Features Products are pre-selected in DC current gain Application General purpose Description These epitaxial planar transistors are mounted
Description. Table 1. Device summary
2 A positive voltage regulator IC Description Datasheet - production data Features TO-220 Output current up to 2 A Output voltages of 5; 7.5; 9; 10; 12; 15; 18; 24 V Thermal protection Short circuit protection
EN: This Datasheet is presented by the m anufacturer. Please v isit our website for pricing and availability at www.hest ore.hu.
EN: This Datasheet is presented by the m anufacturer. Please v isit our website for pricing and availability at www.hest ore.hu. 2N3055, MJ2955 Complementary power transistors Features Datasheet - production
DSL01-xxxSC5. Secondary protection for DSL lines. Features. Description. Applications. Benefits. Complies with the following standards
-xxxsc5 Secondary protection for DSL lines Features Low capacitance devices: -xxxsc5: Delta C typ = 3.5 pf High surge capability: 30 A - 8/20 µs Voltage: 8 V, 10.5 V, 16 V, and 24 V RoHS package Benefits
ESDLIN1524BJ. Transil, transient voltage surge suppressor diode for ESD protection. Features. Description SOD323
Transil, transient voltage surge suppressor diode for ESD protection Datasheet production data Features Max peak pulse power 160 W (8/0 µs) Asymmetrical bidirectional device Stand-off voltage: 15 and 4
UA741. General-purpose single operational amplifier. Features. Applications. Description. N DIP8 (plastic package)
General-purpose single operational amplifier Datasheet - production data N DIP8 (plastic package) D SO8 (plastic micropackage) Pin connections (top view) 1 - Offset null 1 2 - Inverting input 3 - Non-inverting
Description SO-8. series. Furthermore, in the 8-pin configuration Very low-dropout voltage (0.2 V typ.)
ery low-dropout voltage regulator with inhibit function TO-92 Bag TO-92 Tape and reel Ammopack 1 2 3 SO-8 Description Datasheet - production data The is a very low-dropout voltage regulator available in
MC33079. Low noise quad operational amplifier. Features. Description
Low noise quad operational amplifier Datasheet production data Features Low voltage noise: 4.5 nv/ Hz High gain bandwidth product: 15 MHz High slew rate: 7 V/µs Low distortion: 0.002% Large output voltage
LM135-LM235-LM335. Precision temperature sensors. Features. Description
Precision temperature sensors Features Directly calibrated in K 1 C initial accuracy Operates from 450µA to 5mA Less than 1Ω dynamic impedance TO-92 (Plastic package) Description The LM135, LM235, LM335
Table 1. Absolute maximum ratings (T amb = 25 C) Symbol Parameter Value Unit. ISO 10605 - C = 330 pf, R = 330 Ω : Contact discharge Air discharge
Automotive dual-line Transil, transient voltage suppressor (TVS) for CAN bus Datasheet - production data Complies with the following standards ISO 10605 - C = 150 pf, R = 330 Ω : 30 kv (air discharge)
AN3332 Application note
Application note Generating PWM signals using STM8S-DISCOVERY Application overview This application user manual provides a short description of how to use the Timer 2 peripheral (TIM2) to generate three
Description. Table 1. Device summary. Order codes. TO-220 (single gauge) TO-220 (double gauge) D²PAK (tape and reel) TO-220FP
1.2 V to 37 V adjustable voltage regulators Description Datasheet - production data TO-220 TO-220FP The LM217, LM317 are monolithic integrated circuits in TO-220, TO-220FP and D²PAK packages intended for
Single LNB supply and control IC DiSEqC 1.X compliant with EXTM based on the LNBH29 in a QFN16 (4x4) Description
Single LNB supply and control IC DiSEqC 1.X compliant with EXTM based on the LNBH29 in a QFN16 (4x4) Data brief Low-drop post regulator and high-efficiency step-up PWM with integrated power N-MOS allowing
BZW50. Transil, transient voltage surge suppressor (TVS) Features. Description
Transil, transient voltage surge suppressor (TVS) Datasheet production data Features Peak pulse power: 5000 W (10/0 µs) Stand-off voltage range from 10 V to 180 V Unidirectional and bidirectional types
AN2389 Application note
Application note An MCU-based low cost non-inverting buck-boost converter for battery chargers Introduction As the demand for rechargeable batteries increases, so does the demand for battery chargers.
HCF4010B HEX BUFFER/CONVERTER (NON INVERTING)
HEX BUFFER/CONVERTER (NON INVERTING) PROPAGATION DELAY TIME: t PD = 50ns (Typ.) at V DD = 10V C L = 50pF HIGH TO LOW LEVEL LOGIC CONVERSION MULTIPLEXER: 1 TO 6 OR 6 TO 1 HIGH "SINK" AND "SOURCE" CURRENT
Description. Table 1. Device summary. Order code Temperature range Package Packing Marking
8-bit shift register with output latches (3-state) Applicatio Datasheet - production data SO16 TSSOP16 Automotive Industrial Computer Coumer Features High speed: f MAX = 59 MHz (typ.) at V CC = 6 V Low
SPC5-FLASHER. Flash management tool for SPC56xx family. Description. Features
Flash management tool for SPC56xx family Data brief Flash verify: check the Flash content with a binary image file Unsecure sequence for censored device: sending the private password selected from the
TDA2004R. 10 + 10 W stereo amplifier for car radio. Features. Description
10 + 10 W stereo amplifier for car radio Features Low distortion Low noise Protection against: Output AC short circuit to ground Overrating chip temperature Load dump voltage surge Fortuitous open ground
STTH2R06. High efficiency ultrafast diode. Features. Description
STTH2R6 High efficiency ultrafast diode Features Very low conduction losses Negligible switching losses Low forward and reverse recovery times High junction temperature Description A K The STTH2R6 uses
STP60NF06. N-channel 60V - 0.014Ω - 60A TO-220 STripFET II Power MOSFET. General features. Description. Internal schematic diagram.
N-channel 60V - 0.014Ω - 60A TO-220 STripFET II Power MOSFET General features Type V DSS R DS(on) I D STP60NF06 60V
STTH1R04-Y. Automotive ultrafast recovery diode. Features. Description
Automotive ultrafast recovery diode Features Datasheet - production data K SMA STTH1R4AY Table 1. Device summary Symbol Value I F(AV) 1 A V RRM 4 V T j (max) 175 C V F (typ) t rr (typ) A K.9 V 14 ns A
STN3NF06L. N-channel 60 V, 0.07 Ω, 4 A, SOT-223 STripFET II Power MOSFET. Features. Application. Description
N-channel 60 V, 0.07 Ω, 4 A, SOT-223 STripFET II Power MOSFET Features Type V DSS (@Tjmax) Exceptional dv/dt capability Avalanche rugged technology 100% avalanche tested R DS(on) max STN3NF06L 60 V < 0.1
AN3353 Application note
Application note IEC 61000-4-2 standard testing Introduction This Application note is addressed to technical engineers and designers to explain how STMicroelectronics protection devices are tested according
STP60NF06FP. N-channel 60V - 0.014Ω - 30A TO-220FP STripFET II Power MOSFET. General features. Description. Internal schematic diagram.
N-channel 60V - 0.014Ω - 30A TO-220FP STripFET II Power MOSFET General features Type V DSS R DS(on) I D STP60NF06FP 60V
TDA2003 10W CAR RADIO AUDIO AMPLIFIER
TDA2003 10W CAR RADIO AUDIO AMPLIFIER DESCRIPTION The TDA 2003 has improved performance with the same pin configuration as the TDA 2002. The additional features of TDA 2002, very low number of external
HCF4001B QUAD 2-INPUT NOR GATE
QUAD 2-INPUT NOR GATE PROPAGATION DELAY TIME: t PD = 50ns (TYP.) at V DD = 10V C L = 50pF BUFFERED INPUTS AND OUTPUTS STANDARDIZED SYMMETRICAL OUTPUT CHARACTERISTICS QUIESCENT CURRENT SPECIFIED UP TO 20V
AN2604 Application note
AN2604 Application note STM32F101xx and STM32F103xx RTC calibration Introduction The real-time clock (RTC) precision is a requirement in most embedded applications, but due to external environment temperature
AN3998 Application note
Application note PDM audio software decoding on STM32 microcontrollers 1 Introduction This application note presents the algorithms and architecture of an optimized software implementation for PDM signal
AN4108 Application note
Application note How to set up a HTTPS server for In-Home display with HTTPS Introduction This application note describes how to configure a simple SSL web server using the EasyPHP free application to
AN3110 Application note
Application note Using the STVM100 to automatically adjust VCOM voltage in e-paper Introduction The widespread use of multimedia electronic devices, coupled with environmental concerns over the manufacturing
AN2680 Application note
Application note Fan speed controller based on STDS75 or STLM75 digital temperature sensor and ST72651AR6 MCU Introduction This application note describes the method of defining the system for regulating
AN3354 Application note
Application note STM32F105/107 in-application programming using a USB host 1 Introduction An important requirement for most Flash-memory-based systems is the ability to update firmware installed in the
AN4368 Application note
Application note Signal conditioning for pyroelectric passive infrared (PIR) sensors Sylvain Colliard-Piraud Introduction Pyroelectric passive infrared (PIR) sensors are widely used in daily life. They
MC34063AB, MC34063AC, MC34063EB, MC34063EC
MC34063AB, MC34063AC, MC34063EB, MC34063EC DC-DC converter control circuits Description Datasheet - production data Features DIP-8 SO-8 Output switch current in excess of 1.5 A 2 % reference accuracy Low
UM1613 User manual. 16-pin smartcard interface ST8034P demonstration board. Introduction
User manual 16-pin smartcard interface ST8034P demonstration board Introduction The purpose of this document is to describe, and provide information on, how to efficiently use the ST8034P smartcard interface
STCS1. 1.5 A max constant current LED driver. Features. Applications. Description
1.5 A max constant current LED driver Features Up to 40 V input voltage Less than 0.5 V voltage overhead Up to 1.5 A output current PWM dimming pin Shutdown pin LED disconnection diagnostic DFN8 (3x3 mm)
STP55NF06L STB55NF06L - STB55NF06L-1
General features STP55NF06L STB55NF06L - STB55NF06L-1 N-channel 60V - 0.014Ω - 55A TO-220/D 2 PAK/I 2 PAK STripFET II Power MOSFET Type V DSS R DS(on) I D STP55NF06L 60V
LM2901. Low-power quad voltage comparator. Features. Description
Low-power quad voltage comparator Features Wide single supply voltage range or dual supplies for all devices: +2 V to +36 V or ±1 V to ±18 V Very low supply current (1.1 ma) independent of supply voltage
P6KE. Transil, transient voltage surge suppressor (TVS) Features. Description. Complies with the following standards
Transil, transient voltage surge suppressor (TVS) Datasheet production data Features Peak pulse power: 600 W (10/0 µs ) Stand-off voltage range 6.8 to 440 V Unidirectional and bidirectional types Low clamping
STGB10NB37LZ STGP10NB37LZ
STGB10NB37LZ STGP10NB37LZ 10 A - 410 V internally clamped IGBT Features Low threshold voltage Low on-voltage drop Low gate charge TAB TAB High current capability High voltage clamping feature Applications
VN05N. High side smart power solid state relay PENTAWATT. Features. Description
High side smart power solid state relay Features Type V DSS R DS(on) I OUT V CC VN05N 60 V 0.18 Ω 13 A 26 V Output current (continuous): 13A @ Tc=25 C 5V logic level compatible input Thermal shutdown Under
STCS1A. 1.5 A max constant current LED driver. Features. Applications. Description
1.5 A max constant current LED driver Features Up to 40 V input voltage Less than 0.5 V voltage overhead Up to 1.5 A output current PWM dimming pin Shutdown pin LED disconnection diagnostic DFN8 (3 x 3
.LOW POWER DISSIPATION .HIGH NOISE IMMUNITY M74HC154 4 TO 16 LINE DECODER/DEMULTIPLEXER. HIGH SPEED tpd = 15 ns (TYP.) at VCC =5V
. HIGH SPEED tpd = 15 ns (TYP.) at VCC =5V.LOW POWER DISSIPATION I CC =4µA (MAX.) at T A =25 C.HIGH NOISE IMMUNITY VNIH =VNIL =28%VCC (MIN.) OUTPUT DRIVE CAPABILITY 15 LSTTL LOADS SYMMETRICAL OUTPUT IMPEDANCE
HCF4081B QUAD 2 INPUT AND GATE
QUAD 2 INPUT AND GATE MEDIUM SPEED OPERATION : t PD = 60ns (Typ.) at 10 QUIESCENT CURRENT SPECIFIED UP TO 20 5, 10 AND 15 PARAMETRIC RATINGS INPUT LEAKAGE CURRENT I I = 100nA (MAX) AT DD = 18 T A = 25
ST19NP18-TPM-I2C. Trusted Platform Module (TPM) with I²C Interface. Features
Trusted Platform Module (TPM) with I²C Interface Data brief Features Single-chip Trusted Platform Module (TPM) Embedded TPM 1.2 firmware I²C communication interface (Slave mode) Architecture based on ST19N
. HIGH SPEED .LOW POWER DISSIPATION .COMPATIBLE WITH TTL OUTPUTS M54HCT27 M74HCT27 TRIPLE 3-INPUT NOR GATE. tpd = 9 ns (TYP.
M54HCT27 M74HCT27 TRIPLE 3-INPUT NOR GATE. HIGH SPEED tpd = 9 ns (TYP.) AT VCC =5V.LOW POWER DISSIPATION I CC =1µA (MAX.) AT T A =25 C.COMPATIBLE WITH TTL OUTPUTS VIH = 2V (MIN.) VIL = 0.8V (MAX) OUTPUT
VN03. ISO high side smart power solid state relay PENTAWATT. Features. Description. www.tvsat.com.pl
ISO high side smart power solid state relay Features Type V DSS R DS(on) I n (1) Maximum continuous output current (a) : 4A @ Tc= 25 C 5V logic level compatible input Thermal shutdown Under voltage protection
HCF4070B QUAD EXCLUSIVE OR GATE
QUAD EXCLUSIE OR GATE MEDIUM-SPEED OPERATION t PHL = t PLH = 70ns (Typ.) at CL = 50 pf and DD = 10 QUIESCENT CURRENT SPECIFIED UP TO 20 5, 10 AND 15 PARAMETRIC RATINGS INPUT LEAKAGE CURRENT I I = 100nA
M24LRxx/CR95HF application software installation guide
User manual M24LRxx/CR95HF application software installation guide Introduction This user manual describes the procedures to install the different software drivers required to use the DEVKIT-M24LR-A development
HCF4028B BCD TO DECIMAL DECODER
BCD TO DECIMAL DECODER BCD TO DECIMAL DECODING OR BINARY TO OCTAL DECODING HIGH DECODED OUTPUT DRIVE CAPABILITY "POSITIVE LOGIC" INPUTS AND OUTPUTS: DECODED OUTPUTS GO HIGH ON SELECTION MEDIUM SPEED OPERATION
AN3359 Application note
Application note Low cost PCB antenna for 2.4GHz radio: Meander design 1 Introduction This application note is dedicated to the STM32W108 product family from STMicroelectronics. One of the main reasons
STEVAL-IEG001V2. Smart real-time vehicle tracking system. Features
Smart real-time vehicle tracking system Data brief Features Real-time vehicle tracking through GPS/GSM/GPRS. Vehicle location coordinates acquired using a Telit GPS module and sent over GPRS to web server-based
UM1676 User manual. Getting started with.net Micro Framework on the STM32F429 Discovery kit. Introduction
User manual Getting started with.net Micro Framework on the STM32F429 Discovery kit Introduction This document describes how to get started using the.net Micro Framework (alias NETMF) on the STM32F429
STB4NK60Z, STB4NK60Z-1, STD4NK60Z STD4NK60Z-1, STP4NK60Z,STP4NK60ZFP
STB4NK60Z, STB4NK60Z-1, STD4NK60Z STD4NK60Z-1, STP4NK60Z,STP4NK60ZFP N-channel 600 V - 1.76 Ω - 4 A SuperMESH Power MOSFET DPAK - D 2 PAK - IPAK - I 2 PAK - TO-220 - TO-220FP Features Type V DSS R DS(on)
AN4156 Application note
Application note Hardware abstraction layer for Android Introduction This application note provides guidelines for successfully integrating STMicroelectronics sensors (accelerometer, magnetometer, gyroscope
STP10NK80ZFP STP10NK80Z - STW10NK80Z
STP10NK80ZFP STP10NK80Z - STW10NK80Z N-channel 800V - 0.78Ω - 9A - TO-220/FP-TO-247 Zener-protected supermesh TM MOSFET General features Type V DSS R DS(on) I D Pw STP10NK80Z 800V
Obsolete Product(s) - Obsolete Product(s)
Vertical deflection booster for 3 App TV/monitor applications with 0 V flyback generator Features Figure. Heptawatt package Power amplifier Flyback generator Stand-by control Output current up to 3.0 App
AN2866 Application note
Application note How to design a 13.56 MHz customized tag antenna Introduction RFID (radio-frequency identification) tags extract all of their power from the reader s field. The tags and reader s antennas
STLM20. Ultra-low current 2.4 V precision analog temperature sensor. Features. Applications
Ultra-low current 2.4 V precision analog temperature sensor Features Precision analog voltage output temperature sensor ±1.5 C maximum temperature accuracy at 25 C (±0.5 C typical) Ultra-low quiescent
AN2824 Application note
Application note STM32F10xxx I 2 C optimized examples Introduction The aim of this application note is to provide I 2 C firmware optimized examples based on polling, interrupts and DMA, covering the four
AN2703 Application note
Application note list for SCRs, TRIACs, AC switches, and DIACS Introduction All datasheet parameters are rated as minimum or maximum values, corresponding to the product parameter distribution. In each
STB75NF75 STP75NF75 - STP75NF75FP
STB75NF75 STP75NF75 - STP75NF75FP N-channel 75V - 0.0095Ω - 80A - TO-220 - TO-220FP - D 2 PAK STripFET II Power MOSFET General features Type V DSS R DS(on) I D STB75NF75 75V
HCF4056B BCD TO 7 SEGMENT DECODER /DRIVER WITH STROBED LATCH FUNCTION
BCD TO 7 SEGMENT DECODER /DRIVER WITH STROBED LATCH FUNCTION QUIESCENT CURRENT SPECIF. UP TO 20V OPERATION OF LIQUID CRYSTALS WITH CMOS CIRCUITS PROVIDES ULTRA LOW POWER DISPLAY. EQUIVALENT AC OUTPUT DRIVE
STCS2A. 2 A max constant current LED driver. Features. Applications. Description
2 A max constant current LED driver Features Up to 40 V input voltage Less than 0.5 V voltage overhead Up to 2 A output current PWM dimming pin Shutdown pin LED disconnection diagnostic Slope control with
Obsolete Product(s) - Obsolete Product(s)
SYNCHRONOUS PROGRAMMABLE 4-BIT BINARY COUNTER WITH ASYNCHRONOUS CLEAR INTERNAL LOOK-AHEAD FOR FAST COUNTING CARRY OUTPUT FOR CASCADING SYNCHRONOUSLY PROGRAMMABLE LOW-POWER TTL COMPATIBILITY STANDARDIZED
Description. IO and RF AGC. ASIC controller and power management. Carrier recovery loop. GPIO switch matrix. Lock indicator and monitoring DVBS2 FEC
Multi-standard advanced demodulator for satellite digital TV and data services set-top boxes Data Brief Features Demodulation DIRECTV TM and DVBS QPSK DVBS2 QPSK and 8PSK Digital Nyquist root filter with
UM0985 User manual. Developing your STM32VLDISCOVERY application using the IAR Embedded Workbench software. Introduction
User manual Developing your STM32VLDISCOVERY application using the IAR Embedded Workbench software Introduction This document provides an introduction on how to use IAR Embedded Workbench for ARM software
VN5R003H-E. 3 mω reverse battery protection switch. Features. Description. Application
3 mω reverse battery protection switch Datasheet production data Features Max supply voltage V CC -16 to 41 V Operating voltage range V CC -16 to 28 V On-state resistance R ON 3mΩ General Optimized electromagnetic
AN2760 Application note
Application note Using clock distribution circuits in smart phone system design Introduction As smart phones become more and more popular in the market, additional features such as A-GPS, Bluetooth, WLAN
NE555 SA555 - SE555. General-purpose single bipolar timers. Features. Description
NE555 SA555 - SE555 General-purpose single bipolar timers Features Low turn-off time Maximum operating frequency greater than 500 khz Timing from microseconds to hours Operates in both astable and monostable
STOD2540. PMOLED display power supply. Features. Application. Description
PMOLED display power supply Features Inductor switches boost controller PFM mode control High efficiency over wide range of load (1 ma to 40 ma) Integrated load disconnect switch Over voltage protection
TDA2822 DUAL POWER AMPLIFIER SUPPLY VOLTAGE DOWN TO 3 V LOW CROSSOVER DISTORSION LOW QUIESCENT CURRENT BRIDGE OR STEREO CONFIGURATION
TDA2822 DUAL POER AMPLIFIER SUPPLY VOLTAGE DON TO 3 V. LO CROSSOVER DISTORSION LO QUIESCENT CURRENT BRIDGE OR STEREO CONFIGURATION DESCRIPTION The TDA2822 is a monolithic integrated circuit in 12+2+2 powerdip,
STM6315. Open drain microprocessor reset. Features
Open drain microprocessor reset Features Low supply current of 1.5µA (typ) ±1.8% reset threshold accuracy (25 C) Guaranteed RST assertion down to V CC = 1.0V Open drain RST output can exceed V CC Power
Getting started with DfuSe USB device firmware upgrade STMicroelectronics extension
User manual Getting started with DfuSe USB device firmware upgrade STMicroelectronics extension Introduction This document describes the demonstration user interface that was developed to illustrate use
STTH110. High voltage ultrafast rectifier. Description. Features
High voltage ultrafast rectifier Datasheet - production data K Description The STTH110, which is using ST ultrafast high voltage planar technology, is especially suited for free-wheeling, clamping, snubbering,
NE555 SA555 - SE555. General-purpose single bipolar timers. Features. Description
NE555 SA555 - SE555 General-purpose single bipolar timers Features Low turn-off time Maximum operating frequency greater than 500 khz Timing from microseconds to hours Operates in both astable and monostable
LM833 LOW NOISE DUAL OPERATIONAL AMPLIFIER
LOW NOISE DUAL OPERATIONAL AMPLIFIER LOW VOLTAGE NOISE: 4.5nV/ Hz HIGH GAIN BANDWIDTH PRODUCT: 15MHz HIGH SLEW RATE: 7V/µs LOW DISTORTION:.2% EXCELLENT FREQUENCY STABILITY ESD PROTECTION 2kV DESCRIPTION
SPC5-CRYP-LIB. SPC5 Software Cryptography Library. Description. Features. SHA-512 Random engine based on DRBG-AES-128
SPC5 Software Cryptography Library Data brief SHA-512 Random engine based on DRBG-AES-128 RSA signature functions with PKCS#1v1.5 ECC (Elliptic Curve Cryptography): Key generation Scalar multiplication
L6219. Stepper motor driver. Features. Description
Stepper motor driver Features Able to drive both windings of bipolar stepper motor Output current up to 750 ma each winding Wide voltage range: 10 V to 46 V Half-step, full-step and microstepping mode
AN3265 Application note
Application note Handling hardware and software failures with the STM8S-DISCOVERY Application overview This application is based on the STM8S-DISCOVERY. It demonstrates how to use the STM8S window watchdog
.OPERATING SUPPLY VOLTAGE UP TO 46 V
L298 DUAL FULL-BRIDGE DRIVER.OPERATING SUPPLY VOLTAGE UP TO 46 V TOTAL DC CURRENT UP TO 4 A. LOW SATURATION VOLTAGE OVERTEMPERATURE PROTECTION LOGICAL "0" INPUT VOLTAGE UP TO 1.5 V (HIGH NOISE IMMUNITY)
HCC/HCF4032B HCC/HCF4038B
HCC/HCF4032B HCC/HCF4038B TRIPLE SERIAL ADDERS INERT INPUTS ON ALL ADDERS FOR SUM COMPLEMENTING APPLICATIONS FULLY STATIC OPERATION...DC TO 10MHz (typ.) @ DD = 10 BUFFERED INPUTS AND OUTPUTS SINGLE-PHASE
UM1727 User manual. Getting started with STM32 Nucleo board software development tools. Introduction
User manual Getting started with STM32 Nucleo board software development tools Introduction The STM32 Nucleo board (NUCLEO-F030R8, NUCLEO-F072RB, NUCLEO-F103RB, NUCLEO-F302R8, NUCLEO-F401RE, NUCLEO-L152RE)