SPECIFICATIONS FOR 30 YARD OPEN TOP ROLL-OFF CONTAINER 4 YARD CAPACITY WASTE COMPACTION UNIT 40 YARD WASTE CONTAINER FOR COMPACTION UNIT

Transcription

1 SPECIFICATIONS FOR 30 YARD OPEN TOP ROLL-OFF CONTAINER 4 YARD CAPACITY WASTE COMPACTION UNIT 40 YARD WASTE CONTAINER FOR COMPACTION UNIT Listed below are the specifications for purchase of the following waste hauling equipment: Thirty (30) yard capacity open top cable hoist type rolloff containers. The bath tub style containers will not be accepted; Standard square bottom design only. Amount-17 Four yard capacity compaction units with fabricated hopper. Amount-4 units Forty (40) yard capacity compactor compatible breakaway cable hoist waste containers. Amount-5. The contractor will be responsible for delivery to and installation of two compaction units with containers to the Crisfield Transfer Station and two complete units to the Mt. Vernon Transfer Station. All labor, supplies, and equipment necessary to complete the installation of the compaction units will be the responsibility of the contractor. All open containers will be delivered to either to the Somerset County Landfill or the Somerset County Roads Department. Service for the compaction units must be available within a 100 mile radius of the Crisfield Transfer Station. 30 Yard Open Top Cable Hoist Waste Container Specifications 1. Length of container 22 feet 8 inches 2. Width 8 feet 3. Inside height Floor to top rail-62 inches 4. Floor- 2 pieces ¼ sheet steel butt welded 5. Understructure 3 channel 4.l/ lbs/ft on 16 apart 6. Long rails 2 x 6 x ¼ tubing 7. Bullnose Solid 1 ¼ plate burnout 8. Hook plate 23 x 15 x 3/4 9. Push plate 26 x 16 x 3/ Cable hookup 11. Hook 1 ¼ flame cut steel inserted through hook. plate, weld both sides 12 Nose roller 4 diameter x 6 long solid tubing with grease fittings 13. Wheel axle 1 ½ solid round bar 14. Wheels Steel 8 x 10 long rear, 8 x 6 long front 15. Side walls 12 gauge steel No bent top rails 16. Door 10 gauge steel 3 x 4 x 11 gauge structural tubing with 2-3 x 4 x 11 gauge tube cross members, 3 heavy duty hinges

2 with grease fittings, 30 handle, 2 latches, 1 door fork, and ¼ chain lock. Latch system- uplift 17. Bulk head 10 gauge steel 18. Top Rail 3 x 4 x 7 gauge tubing 19. Side Post 3 x 5 x 11 gauge formed on 24 centers with 1 drain port/weep hole 20. Rear Corner Post 3 ½ x 7 x 3/16 formed 21. Tailgate sheet 10 gauge 22. Tailgate latch Vertical lift handle 23. Tailgate Frame Vertical 3 x 4 x 7 gauge tubing, horizontal 3 x 5 x 10 gauge formed tube with dirt shedder top. 24. Hinges: Heavy duty machine type, three on 62 and higher 25. Paint Chemically degreased, welds ground smooth and sand blasted. Prime and paint one color with an exterior latex paint. Color-Blue- Shade to be decided by the County after award of contract. 26. Ladder Ladder and tarp rails on each side made with 5/8 hot rolled rounds 27. Container Front Container front- 11 gauge steel with a 3 x 4 x 11 gauge top cap and 11 gauge dog box which houses the hook station. Dog box should be supported by 2 X 6 X 11 gauge structural tubing running from top to bottom of front and supported by 2 x 6 x 11 gauge cross members. Corners are to be covered with 4 x 8: x 11 gauge corner angles. 28. Container Style-Cable Hook Containers shall be cable/hook and rails compatible with existing County owned recycling containers. Delivery Date- July 1, 2014 Delivery location-somerset County Landfill or Somerset County Roads Department Westover, Md. Number of open top 30 yard containers- 17

3 40 Yard Cable Hoist Octagonal Packer Receiver Waste Container for Compaction Unit 1. Length- 22 feet 8 inches 2. Width 3. Understructure 3 channel 4.1 lbs/ft at 16 apart 4. Long rails 2 x 6 x 1.4 tubing 5. Bullnose Solid 1 ¼ plate burnout 6. Floor 3/16 2 pieces butt welded 7. Push plate 26 x 16 x 3/16 8. Hook plate 23 x 15 x ¾ 9. Wheels 8 x 10 long rear only 10. Wheel axles 1 ½ solid round bar 11. Nose roller 4 diameter x 6 long 12. Side wall and roof 7 gauge with 5 taper per side from rear to front 13. Bulkhead 7 gauge 14. Front Post 3 x 5 formed on 24 centers 15. Tailgate sheet 7 gauge 16. Tailgate frame Vertical and horizontal 3 x 4 x 7 gauge Tubing 17. Rear Corner Post 2 x 6 x ¼ tubing 18. Tailgate latch Vertical lift handle 19. Hinges Heavy duty machine type, three on 62 and Higher 20. Paint Chemically degreased. All welds ground smooth and sand blasted. Prime and paint one color with an exterior latex paint. Color blue-shade to be determined at the time of the contract. 21. Fire Port Minimum 2 fire port with screw cap at the midway point on both sides of the box 22. Ratchet Cam Latch One each side to ratchet the waste receiver container to the compaction unit. 23. Container front 11 gauge steel dog box which houses the Hook station. Dog box should be supported by 2 x 6 x 11 gauge structural tubing running from top to bottom of the front and supported by 2 x 6 x 11 gauge cross members. Corners are to be covered with 4 x 8 x 11 gauge corner angles. 24. Ratchet Cam Latch Hole The box corner post will be reinforced with an 8 x 8 ¾ thick steel plate with a 4 x4 cutout hole for the ratchet latch inch long by ½ thick gussets will be installed on each corner for additional strength.

4 25. MAWS 15 guide tracks with stops for each unit. Total of 4 units 26. Number of containers Number of cloth cover/diapers for the open end. (6) The waste containers shall be compatible with the compactor units supplied. The boxes will be designed to break away from the stationary compaction unit. The container will be supplied with rubber gasket material to prevent leakage between the compactor and the waste container box opening. The container will be constructed for a cable hoist roll-off system compatible with the recycling containers currently owned by the County. Number of containers- 5 Number of cloth opening covers- 6 Delivery Date- July 1, 2014 Delivery location- Somerset County Landfill or Somerset County Roads Department- Stationary 4 Yard Compactor Unit The following are the specifications for 4 four cubic yard compaction units to be delivered to and installed at the following locations: Crisfield Transfer Station-Rt. 413, Crisfield, Md., Mt. Vernon Transfer Station, Mt. Vernon Road, Princess Anne, Md. Each transfer station will receive 2 units. The units will be stationary and only the 40 yard container will be removed for disposal of the waste. The bid will include installation of the compactors, electrical supplies, labor, and all other parts necessary to complete the project. The equipment supplier will provide 8 hours of Operation and Maintenance Training for Solid Waste and Maintenance personnel. 1. Charge Box 4.0 cubic yards 2. Clear top opening 65 length x 60 width 3. Overall dimension length 180 x 72.5 Height Weight with power unit 6,600 to 6,700 lbs. 5. Cycle time second cycle Multicycle-Three passes 6. Ram Force 48,000 lbs. 7. Ram penetration 14

5 a. Ram height b. Ram face plate ½ steel with ¾ stiffener plates c. Ram base plate 3/8 steel with 10 gauge formed stiffeners d. Ram top plate ¼ steel with 10 gauge formed stiffeners e. Ram side plates ¼ formed plate 8. Electric 208/230/460, 3 phase 60Hz 9. Motor 15 HP with 3 Phase motor starter & heaters 10. Power box UL rated, TEFC housing- Must meet ANSI Z Safety Standards 11. Electrical Panel NEMA 4 Weather Proof Gasketed Panel 12. Automatic Cycle Operation Turn key, push button start for three Cycles with manual cutoff button 13. Low Temperature Oil: 0 Degree Fahrenheit Operation 14. Heavy Duty 1 3/8 ratchet binders with 1 thick hooks rated at 70,000 lbs. 15. Override-Packet-Pressure-Boost 16. Automatic Maintenance Scheduler 17. Container full light and auto shutdown- 18. Oil filled pressure gauge on 15 hose 1 gauge per unit- 0 to 3,000 psi. 19. Key start-auto 20. Push button start for three cycles 21. Three sided hopper built on site Side feed-walk-up Application primed and painted to match the container color. (Blue) 22. Hydraulic oil tank heater for each unit-total ½ thick ram floor 24. Heavy duty breaker bar 8 x 8 x 1 angled steel 25. Compactor head floor ½ steel with 10 gauge channels at 12 spacing 26. Compactor head sides ¼ steel formed vertical and formed horizontal stiffeners 27. Compactor head top deck 12 gauge steel Volt operator controls

6 All equipment must be available for installation by July 1, Payment for equipment will be made on or after July 1, The County is currently contracting for waste hauling services. Each of the two transfer stations has two compaction units in place. The County will request that the current contractor remove one compaction unit at a time. Installation of each new compactor with container must occur within one (1) week after notification by the County to proceed. The contractor must be able to provide technical or mechanical onsite service to each of the two transfer station sites from within a 100 mile radius.