A. Extent of hardware required is indicated on drawings and in schedules.

Transcription

1 SECTION PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division -1 Specification Sections, apply to this Section. 1.2 SUMMARY A. Extent of hardware required is indicated on drawings and in schedules. B. Related Work Specified in other Sections: 1. Division 6 Section "Interior Architectural Woodwork" for casework hardware. 1.3 QUALITY ASSURANCE A. Definition: 1. "Hardware" includes items known commercially as finish hardware which are required for swing, sliding and folding doors, except special types of unique and non-matching hardware specified in the same section as the door and door frame. Hardware shall be furnished and installed as part of the work of this section. B. Requirements of Regulatory Agencies: 1. Provide hardware to comply with the requirements of laws, codes, ordinances, and regulations of governmental agencies having jurisdiction. Where such requirements exceed the requirements of the Specifications, furnish the most stringent. 2. Hardware to hazardous areas of public buildings shall comply with the requirements of the governmental agencies having jurisdiction. For public building accommodations, comply with governmental laws and regulations for the physically handicapped. C. Hardware Supplier: 1. An established hardware supplier who is a factory authorized distributor for all products required, and has display samples, inventory, and qualified personnel trained and experienced in preparing Hardware Schedules, issuing templates, and ordering, furnishing, and servicing hardware for architecturally designed projects, who employs an experienced Architectural Hardware Consultant who is available to FIRSTMERIT BANK PROJECT NO.: /29/16 10:26 AM

2 Owner, Architect and Contractor, at reasonable times during the course of the work, for consultation about project's hardware requirements. D. Preconstruction Meeting: 1. Prior to commencement of the Hardware Supplier's development of the Hardware Schedule, a Hardware Meeting will be held at the Architect's office. The Construction Manager and the Hardware Supplier's personnel directly responsible for preparing the Hardware Schedule shall meet with the Architect and the Architect's Hardware Consultant. Attendance at this meeting is mandatory. E. Pre-installation Seminar: a. Purpose of the meeting is to review the Contract Documents' hardware schedule requirements and will include, but not be limited to, the following: 1) Review specification requirements for hardware schedule, formats, hardware locations, opening descriptions, and other information specified. 2) Review products specified versus products proposed. 3) Hardware Supplier shall distribute, at the meeting, samples of schedules from other projects of similar nature prepared by the same person as will prepare schedule for this Project. 1. Before the installation of hardware begins, the Construction Manager shall request that a hardware installation seminar for the installation of door closers exit devices, and locksets be conducted by the manufacturer's representative of these products. Seminar to be held at job site and attended by all installers of hardware, such as aluminum doors and carpentry installers. Seminar will address proper coordination and installation of exit devices, door closers, and weatherstripping, as detailed in the hardware schedule for this Project, with the use of installation manuals, hardware schedule, templates, physical product samples, and exit device installation videos. 1.4 SUBMITTALS A. General: 1. Submit the following according to Conditions of the Contract and Division 1 Specification Sections. B. Product Data: 1. None required. C. Shop Drawings: PROJECT NO.: FIRSTMERIT BANK /29/16 10:26AM

3 1. None required, except as may be noted under Section "Door Schedule" or under heading "Hardware Schedule". D. Samples: 1. None required, except as may be noted under Section "Door Schedule" or under heading "Hardware Schedule". E. Hardware Schedules: 1. Submit proper number of Hardware Schedules to allow the Architect to retain two copies for his use, a copy for the Owner for his use, plus the number of copies required by the Contractor for its distribution and use. Include the following information in vertical format only. Horizontal format schedule will be returned without review noted "Not Approved". 2. Submit as an integral part of the Hardware Schedule a complete riser and wiring diagram for each different application of all the electrical components being provided for doors with electrical components. 3. Elevation and Wiring Drawings: a. Submit elevation drawing showing relationship of all electrical and pneumatic hardware components to door and frame. Indicate number and gage of wires required. Indicate size of air tubing required. Indicate PSI requirements. b. Submit wiring drawing showing point to point wire hook up for all components. c. Submit drawing showing point to point hookup of air tubing for all components. d. Submit system operations descriptions for each of opening; describe each possible condition. 4. Door Index, using Architect's Door Numbers, Hardware Set numbers and page numbers where hardware is listed. 5. Preface sheet listing category only and manufacturers' names of items being furnished, as follows: CATEGORY SPECIFIED SCHEDULED Hinges Manufacturer A Manufacturer B Locksets Manufacturer X Manufacturer X Kick Plates Open Manufacturer Z 6. Opening Description: a. Single or pair, number, room locations, hand, active leaf, degree of swing, size, material, frame material, and UL Listed. FIRSTMERIT BANK PROJECT NO.: /29/16 10:26 AM

4 7. Hardware Description: a. Quantity, category, product number, fasteners, and finish. 8. Headings that refer to the specified Hardware Set Numbers. 9. Scheduling sequence shown in Hardware Sets. 10. Product data of each hardware item, and shop drawings where required, for items to be connected to the electrical or fire alarm systems complete with power requirements and wiring diagrams and for other special conditions and specialty hardware. 11. Typed copy. 12. Double spacing /2 x 11 inch sheets. 14. U.S. Standard finish symbols. 15. Consecutively numbered pages. 1.5 PRODUCT DELIVERY, STORAGE AND HANDLING A. Label each item of hardware with the appropriate door number and Hardware Schedule heading number, and deliver individually packaged hardware items at the proper times to the proper locations (shop or project site) for installation. PART 2 - PRODUCTS 2.1 MATERIALS A. General: 1. Provide each category with the products of only one manufacturer, unless specified otherwise; this requirement is mandatory whether various manufacturers are listed or not. 2. Manufacturers named under each heading item are acceptable subject to compliance with requirements directly specified or by means of meeting requirements for the listed manufacturer. B. Hinges: a. Where only one manufacturer or product is specified, the phrase "No Substitution" shall apply. 3. Provide hardware made to template. 1. Numbers listed are Ives (IVE). PROJECT NO.: FIRSTMERIT BANK /29/16 10:26AM

5 a. Equal products from any B.H.M.A. member will also be acceptable. C. Mortise Locksets and Latchsets: 1. Function numbers listed are Schlage (SCH) L9000 series with 07A lever trim. a. Best 40H b. Corbin-Russwin ML Provide strikes with extended lips where required to protect trim from being marred by latch bolt. Provide strike lips which do not project more than 1/8" beyond doorframe trim at single doors and have 7/8" lip to center at pairs of 1-3/4" doors. D. Fire Exit Hardware: E. Closers: 1. Function numbers listed are Von Duprin (VON) 98 series. a. Sargent Review the door frame and plan details to determine the proper length of arm and the degree of swing. The degree of swing must be indicated in the Hardware Schedule. 2. Provide accessories such as drop plates, panel adapters, spacers and supports as required to correctly install door closers. 3. Closers listed are LCN 4000 series. F. Door Stops: a. Sargent Function numbers listed are Ives (IVE) FS & WS series. G. Door Gaskets: a. Equal products from any B.H.M.A. member will also be acceptable. 1. Products listed in sets are from National Guard Products (NGP). a. Pemko b. Reese c. Zero FIRSTMERIT BANK PROJECT NO.: /29/16 10:26 AM

6 H. Miscellaneous: 1. Provide items not categorized in the above descriptions, but specified by manufacturers' names in hardware sets. 2. Provide frame marking jigs, if required, for Continuous Hinges. I. Fasteners: 1. Provide fasteners of the proper type, size, quantity, and finish. Provide machine screws and expansion shields for attaching hardware to concrete or masonry, and wall grip inserts at hollow wall construction. 2. Provide end caps for Pulls, Offset Pulls, and face ends of push-pull units. 3. Provide sex bolts for closers at lead lined doors. J. Finishes: 1. Furnish finish for each item as indicated in sets. K. Templates and Hardware Location: 1. Provide hardware made to template. Supply required templates and hardware locations to the door and frame manufacturers. 2. Refer to Article "INSTALLATION", "Locations" and coordinate with templates. L. Cylinders and Keying: 1. Provide Coirbin-Russwin cylinders for all hardware items capable of being locked; keyed per the owner s instructions. 2. Furnish two keys per cylinder. PART 3 - EXECUTION 3.1 INSTALLATION A. General: 1. Install hardware according to manufacturer's printed instructions and to template dimensions. Refer to Cylinders and Keying regarding replacement of construction cores with final cores. 2. Install hardware according to manufacturers' printed instructions and to template dimensions. Refer to Cylinders and Keying regarding conversion of construction cores to final cores. 3. Apply stop seals with no interruptions at head and jambs. PROJECT NO.: FIRSTMERIT BANK /29/16 10:26AM

7 4. Apply weatherstripping to head and jamb stops with no cutouts for stop applied hardware. 5. Closers shall be inspected and adjusted after installation and after the HVAC System is in operation by the Factory Representative to insure proper adjustment in operation. The Manufacturer's Representative shall prepare written report stating compliance, and also recording locations and kind of non-compliance. The original report shall be forwarded to the Architect with a copy to the Contractor and Hardware Distributor. 6. Drill and countersink screw holes for oval head undercut screws. 7. Door edgings shall have cutouts made for bottom flush bolts and for lock and latch fronts and strikes. Bevel top edges to continue bevel pattern in armor and niche plates. 8. When faces of door frames are flush with adjacent walls, thresholds shall be coped at stops and mullions, but not in front of faces of frames. 9. Attach closers with wood screws at wood doors and machine screws at metal doors. a. Attach closers with wood screws at wood doors and machine screws at metal doors. B. Templates and Hardware Locations: 1. Provide required templates and hardware locations to the door and frame manufacturers. 2. Mortising is not required for steel channel or tube steel frames. 3. Dimensions are from finish floor to center line of items. 4. Include this list in Hardware Schedule. CATEGORY DIMENSION C. Quantities: Hinges Door Manufacturer's Standard Flush Bolt Levers 72" and 12" Levers Door Manufacturer's Standard 1. Provide one hinge for each 30 inches of door height, or fraction thereof, except where quantities are specified otherwise. 2. Provide one additional intermediate pivot for doors over 90 inches. 3. Provide hinges, electric hinges, pivot sets, electric pivots, roller latches, exit devices, push and pull hardware, closers, overhead holders, kick plates, armor plates, door edgings, bumpers, stops, seals, automatic bottoms, bottom seals, weatherstripping, and thresholds for both leaves of pairs and batteries unless specified otherwise. FIRSTMERIT BANK PROJECT NO.: /29/16 10:26 AM

8 3.2 ADJUST, CHECK, AND CLEAN A. Adjust, Check, and Clean: 1. Provide the services of a hardware supplier s or manufacturer s representative to inspect and adjust each item of hardware to ensure proper installation and operation of every unit, prior to Owner's occupancy. Replace units which cannot be adjusted to operate freely and smoothly as intended for the application made. Clean hardware to restore finish. 2. Adjust hardware to meet ADA and other pertinent code and regulatory requirements. 3.3 HARDWARE SETS HW SET: 01 1 EA CONTINUOUS HINGE 224 HD 628 IVE 1 EA FIRE EXIT HARDWARE 98NL-F 990NL 626 VON 1 EA RIM CYLINDER CORBIN RUSSWIN 626 C-R 1 EA SURFACE CLOSER 4111 CUSH 689 LCN 1 EA KICK PLATE X 2 LDW 630 IVE 1 SET SMOKE SEAL 2525B BRN NGP HW SET: 02 3 EA HINGE 5BB1 4.5 X IVE 1 EA STOREROOM LOCK L9080L 07A 626 SCH 1 EA MORTISE CYLINDER CORBIN RUSSWIN 626 C-R 1 EA WALL STOP WS IVE END OF SECTION PROJECT NO.: FIRSTMERIT BANK /29/16 10:26AM