RACO Interior OfficeFronts. SolutionsII Typical Details. SolutionsII

Transcription

1 SolutionsII 1

2 SolutionsII Product Typical Overview Details I. GENERAL DESCRIPTION Work Included: Furnish all necessary materials, labor and equipment for the complete installation of interior aluminum framing as shown on the drawings and specified herein. (Specifier Note: It is suggested that related items such as aluminum & wood entrance doors, glass, be included whenever possible.) Work Not Included: Structural support of the framing system, interior closures, trim. (Specifier list other exclusions). Related Work Specified Elsewhere: (Specifier list). QUALITY ASSURANCE Drawings and specifications are based on the Solutions II Interior Officefronts(TM) System as manufactured by RACO Interior Products, Inc. Whenever substitute products are to be considered, supporting technical literature, samples, drawings and performance data must be submitted ten (10) days prior to bid in order to make a valid comparison of the products involved. Test reports certified by an independent test laboratory must be made available upon request. II. PRODUCTS MATERIALS Extrusions shall be 6063-T5 alloy and temper (A.S.T.M. B221 alloy T5 temper). Fasteners, shall be aluminum, stainless steel or zinc plated steel in accordance with A.S.T.M. A 164. Glazing gaskets shall be E.P.D.M. elastomeric extrusions. FINISH All exposed framing surfaces shall be free of scratches and other serious blemishes. Aluminum extrusions shall be given a caustic etch followed by an anodic oxide treatment to obtain... (Specify one of the following): #14 Clear anodic coating #63 Bronze Paint #65 Black Paint #61 White Paint #62 Grey Paint #88 Custom Match Paint 2

3 SolutionsII Product Typical Overview Details FABRICATION The framing system shall provide for flush glazing on all sides with no projecting stops. Vertical and horizontal framing members shall have a nominal face dimension of (Specify). III. EXECUTION INSTALLATION All glass and door framing shall be set in correct locations as shown in the details and shall be level, square, plumb and in alignment with other work in accordance with the manufacturers installation instructions and approved shop drawings. All work shall start from bench marks and / or column lines as established by the architectural drawings and the general contractor with guaranteed accuracy. PROTECTION AND CLEANING After installation the General Contractor shall adequately protect exposed portions of aluminum surfaces from damage by grinding and polishing compounds, plaster, lime, acid, cement, or other contaminants. The General Contractor shall be responsible for final cleaning in accordance with A.A.M.A. specifications for anodize 3

4 SolutionsII Product Typical Overview Details RACO Interior OfficeFronts door frames, sidelights and borrowed light frames can be shipped to the job site K.D., as open assembled panels, or as shop glazed panels ready for installation into finished drywall openings as shown on the approved shop drawings. Solutions II framing features screw race joinery. Horizontal and vertical mullions are joined together with screws driven through the back of the two piece (split) vertical members into the extruded screw splines in the horizontals. Solutions II offers the architect/designer unlimited design possibilities with standard 1½", 2", 3", 4" and 5" trim profiles that can be mixed and matched on door frames and borrowed light Top load, push-in gaskets Borrowed and sidelight openings provide for flush glazing on all four sides with no projecting glass stops or exposed fasteners. Top load glazing gaskets are used on both sides of the glass to secure it into the aluminum glazing pockets and eliminate visible raw glass edges. 4

5 SolutionsII Reference Typical Details Drawings Door Frame Door Frame with Sidelight See reference matrix pages for typical details information. 5

6 SolutionsII Reference Typical Details Drawings Door Frame with Partial Height Sidelight Door Frame with Transom See reference matrix pages for typical details information. 6

7 SolutionsII Reference Typical Details Drawings Door Frame with Sidelight and Transom Borrowed Light See reference matrix pages for typical details information. 7

8 SolutionsII Reference Typical Details Drawings Partial Height Borrowed Light Cased Opening See reference matrix pages for typical details information. 8

9 SolutionsII Reference Typical Details Drawings Corners RN255 RN255 RN252 RN252 RN252 RN252 RN252 RN252 RC306 RC RR238 JR454 JD454 RR519 RR517 RR212 NS /2" 4 1/2" RR213 JP454 JP JD454 JD /2" 4 1/2" JD454 JR See reference matrix pages for typical details information. 9

10 SolutionsII Reference Typical Details Matrix 375 Series Elevation Number 1 ½ Profile 2 Profile 3 Profile 4 Profile 5 Profile 1 N2-1, N2-2 N2-15 N2-29 N2-43 N N2-3 N2-17 N2-31 N2-45 N N2-4 N2-18 N2-32 N2-46 N N2-5, N2-6 N2-19, N2-20 N2-33, N2-34 N2-47, N2-48 N2-61, N N2-7, N2-8 N2-21 N2-35 N2-49 N N2-7 N2-21 N2-35 N2-49 N N2-9 N2-23 N2-37 N2-51 N N2-10, N2-11 N2-16, N2-22 N2-24, N2-25 N2-30, N2-36 N2-38, N2-39, N2-44, N2-50 N2-52, N2-53 N2-58, N2-64 N2-66, N2-67 N2-71, N N2-12 N2-26 N2-40 N2-54 N N2-13 N2-27 N2-41 N2-55 N N2-14 N2-73 N2-28 N2-83 N2-42 N2-84 N2-56 N2-85 N2-70 N N2-74 N2-87 N2-88 N2-89 N N2-75 N2-91 N2-92 N2-93 N N2-76 N2-95 N2-96 N2-97 N N N N N N N2-82 See reference elevation pages for typical details information. 10

11 SolutionsII Reference Typical Details Matrix 487 Series Elevation Number 1 ½ Profile 2 Profile 3 Profile 4 Profile 5 Profile 1 N3-1, N3-2 N3-15 N3-29 N3-43 N N3-3 N3-17 N3-31 N3-45 N N3-4 N3-18 N3-32 N3-46 N N3-5, N3-6 N3-19, N3-20 N3-33, N3-34 N3-47, N3-48 N3-61, N N3-7, N3-8 N3-21 N3-35 N3-49 N N3-7 N3-21 N3-35 N3-49 N N3-9 N3-23 N3-37 N3-51 N N3-10, N3-11 N3-16, N3-22 N3-24, N3-25 N3-30, N3-36 N3-38, N3-39, N3-44, N3-50 N3-52, N3-53 N3-58, N3-64 N3-66, N3-67 N3-71, N N3-12 N3-26 N3-40 N3-54 N N3-13 N3-27 N3-41 N3-55 N N3-14 N3-73 N3-28 N3-83 N3-42 N3-84 N3-56 N3-85 N3-70 N N3-74 N3-87 N3-88 N3-89 N N3-75 N3-91 N3-92 N3-93 N N3-76 N3-95 N3-96 N3-97 N N N N N N N3-82 See reference elevation pages for typical details information. 11

12 RN /2" 1-1/2" RN255 RN255 N2-001_375_1.5-inch_door-head_at-drywall.dxf See also N2-002 N2-002_375_1.5-inch_door-head.dxf See also N2-001 RN255 RN /2" 1-1/2" N2-003_375_1.5-inch_hinge-jamb.dxf N2-004_375_1.5-inch_strike-jamb.dxf 12

13 RN255 RN254 RN254 RN /2" N2-005_375_1.5-inch_strike-jamb_at-glass.dxf See also N /2" N2-006_375_1.5-inch_hinge-jamb_at-glass.dxf See also N2-005 RN /2" 1-1/2" RN252 RN252 N2-007_375_1.5-inch_head_and_jamb.dxf See also N2-008 N2-008_375_1.5-inch_head.dxf See also N2-007 RN250 RN251 RN251 RN /2" 1-1/2" RN261 N2-009_375_1.5-inch_horizontal-mullion.dxf N2-010_375_1.5-inch_sill_at-drywall_one-snap.dxf See also N2-011, N2-016, N

14 RN258 RN258 RN250 RN251 RN /2" 1-1/2" RN256 N2-011_375_1.5-inch_sill_at-drywall_two-snap.dxf See also N2-010, N2-016, N2-022 N2-012_375_1.5-inch_transom-bar.dxf RN /2" RN252 RN /2" N2-013_375_1.5-inch_vertical-mullion.dxf N2-014_375_1.5-inch_cased-head_and_jamb_and_sill.dxf 3 3/4" RN250 RN /16" RN /2" RN255 RN220 N2-015_375_2-inch_door-head.dxf N2-016_375_1.5-inch_sill_one-snap.dxf See also N2-010, N2-011, N

15 RN417 RN /4" 3 3/4" RN255 RN /16" 1-15/16" N2-017_375_2-inch_hinge-jamb.dxf N2-018_375_2-inch_strike-jamb.dxf RN417 RN417 RN255 RN253 RN255 RN /16" 1-15/16" N2-019_375_2-inch_strike-jamb_at-glass.dxf See also N2-020 N2-020_375_2-inch_hinge-jamb_at-glass.dxf See also N

16 3 3/4" RN258 RN /16" RN417 RN /2" RN221 RN252 N2-021_375_2-inch_head_and_jamb.dxf N2-022_375_1.5-inch_sill_two-snap.dxf See also N2-010, N2-011, N2-016 RN250 RN251 RN250 RN251 RN /16" RN /16" RN254 N2-023_375_2-inch_horizontal-mullion.dxf N2-024_375_2-inch_sill_at-drywall_one-snap.dxf See also N2-025, N2-030, N2-036 RN250 RN251 RN258 RN258 RN /16" RN417 RN /16" RN260 N2-025_375_2-inch_sill_at-drywall_two-snap.dxf See also N2-024, N2-030, N2-036 N2-026_375_2-inch_transom-bar.dxf 16

17 RN417 RN203 RN /16" RN252 RN /4" 1-15/16" N2-027_375_2-inch_vertical-mullion.dxf N2-028_375_2-inch_cased-head_and_jamb_and_sill.dxf RN250 RN251 RN443 3" RN /16" RN221 RN255 N2-029_375_3-inch_door-head.dxf N2-030_375_2-inch_sill_one-snap.dxf See also N2-024, N2-025,N

18 RN443 RN443 RN255 RN255 3" 3" N2-031_375_3-inch_hinge-jamb.dxf N2-032_375_3-inch_strike-jamb.dxf RN443 RN443 RN255 RN252 RN252 RN255 3" 3" N2-033_375_3-inch_strike-jamb_at-glass.dxf See also N2-034 N2-034_375_3-inch_hinge-jamb_at-glass.dxf See also N

19 RN258 RN258 RN443 3" RN417 RN214 RN /16" RN252 N2-035_375_3-inch_head_and_jamb.dxf N2-036_375_2-inch_sill_two-snap.dxf See also N2-024, N2-025, N2-030 RN250 RN251 RN250 RN251 RN443 3" RN443 3" RN252 N2-037_375_3-inch_horizontal-mullion.dxf N2-038_375_3-inch_sill_at-drywall_one-snap.dxf See also N2-39, N2-044, N2-050 RN250 RN251 RN258 RN258 RN443 3" RN214 RN443 3" RN255 N2-039_375_3-inch_sill_at-drywall_two-snap.dxf See also N2-038, N2-044, N2-050 N2-040_375_3-inch_transom-bar.dxf 19

20 RN443 RN203 RN443 3" RN252 R N252 3" N2-041_375_3-inch_vertical-mullion.dxf N2-042_375_3-inch_cased-head_and_jamb_and_sill.dxf RN250 RN251 RN443 3" RN443 4" RN222 RN255 N2-044_375_3-inch_sill_one-snap.dxf See also N2-038, N2-039, N2-050 N2-043_375_4-inch_door-head.dxf 20

21 RN419 RN419 RN255 RN255 4" 4" N2-045_375_4-inch_hinge-jamb.dxf N2-046_375_4-inch_strike-jamb.dxf RN419 RN419 RN255 RN252 RN252 RN255 4" 4" N2-047_375_4-inch_strike-jamb_at-glass.dxf See also N2-048 N2-048_375_4-inch_hinge-jamb_at-glass.dxf See also N

22 RN258 RN258 RN419 4" RN214 RN443 3" RN252 RN222 N2-049_375_4-inch_head_and_jamb.dxf N2-050_375_3-inch_sill_two-snap.dxf See also N2-038, N2-039, N2-044 RN250 RN251 RN250 RN251 RN419 4" RN419 4" RN252 N2-051_375_4-inch_horizontal-mullion.dxf N2-052_375_4-inch_sill_at-drywall_one-snap.dxf See also N2-053, N2-058, N

23 RN250 RN251 RN258 RN258 RN214 RN419 4" RN419 4" RN255 N2-053_375_4-inch_sill_at-drywall_two-snap.dxf See also N2-052, N2-058, N2-064 N2-054_375_4-inch_transom-bar.dxf RN419 RN203 RN419 4" RN252 R N252 4" N2-055_375_4-inch_vertical-mullion.dxf N2-056_375_4-inch_cased-head_and_jamb_and_sill.dxf 23

24 RN250 RN251 RN419 4" RN445 5" RN223 RN255 N2-058_375_4-inch_sill_one-snap.dxf See also N2-052, N2-053, N2-064 RN445 N2-057_375_5-inch_door-head.dxf RN445 RN255 5" N2-060_375_5-inch_strike-jamb.dxf RN255 5" N2-059_375_5-inch_hinge-jamb.dxf 24

25 RN445 RN252 RN255 RN445 5" N2-061_375_5-inch_strike-jamb_at-glass.dxf See also N2-062 RN252 RN255 5" N2-062_375_5-inch_hinge-jamb_at-glass.dxf See also N2-061 RN258 RN258 RN445 5" RN214 RN419 4" RN252 RN223 N2-063_375_5-inch_head_and_jamb.dxf N2-064_375_4-inch_sill_two-snap.dxf See also N2-052, N2-053, N

26 RN250 RN251 RN250 RN251 RN445 5" RN445 5" RN252 N2-065_375_5-inch_horizontal-mullion.dxf N2-066_375_5-inch_sill_one-snap.dxf See also N2-067, N2-071, N2-072 RN250 RN251 RN258 RN258 RN214 RN445 5" RN445 5" RN255 N2-067_375_5-inch_sill_two-snap.dxf See also N2-066, N2-071, N2-072 N2-068_375_5-inch_transom-bar.dxf 26

27 RN445 RN203 RN445 5" RN252 R N252 5" N2-069_375_5-inch_vertical-mullion.dxf N2-070_375_5-inch_cased-head_and_jamb_and_sill.dxf RN250 RN251 RN258 RN258 RN214 RN445 5" RN445 5" RN224 RN224 N2-071_375_5-inch_sill_one-snap.dxf See also N2-066, N2-067, N2-072 N2-072_375_5-inch_sill_two-snap.dxf See also N2-066, N2-067, N

28 RN255 RN252 N2-073_375_1.5-inch_door-and-glass_corner_at-drywall.dxf RN252 RN252 N2-074_375_1.5-inch_glass-and-glass_corner_at-drywall.dxf 28

29 RN255 RN252 N2-075_375_1.5-inch_door-and-glass_corner.dxf RC306 RN252 RN252 N2-076_375_1.5-inch_glass-and-glass_corner.dxf RC306 29

30 JR /2" JP454 N2-077_375_1-way_corner.dxf JD /2" JP454 N2-078_375_2-way_corner.dxf 30

31 RR238 RR212 RR519 RR517 NS700 RR213 N2-079_375_radius_corner.dxf N2-080_375_adjustable_corner.dxf JD454 JD /2 4-1/2" JR454 JD454 N2-081_375_3-way_corner.dxf N2-082_375_4-way_corner.dxf 31

32 RN417 RN255 RN252 RN417 RN443 N2-083_375_2-inch_door-and-glass_corner_at-drywall.dxf RN443 RN255 CLIP RN252 CLIP RN443 N2-084_375_3-inch_door-and-glass_corner_at-drywall.dxf 32

33 RN419 RN255 CLIP RN252 CLIP RN419 N2-085_375_4-inch_door-and-glass_corner_at-drywall.dxf RN445 RN255 RN252 CLIP CLIP RN445 N2-086_375_5-inch_door-and-glass_corner_at-drywall.dxf 33

34 RN417 RN252 RN252 RN417 N2-087_375_2-inch_glass-and-glass_corner_at-drywall.dxf RN443 RN252 CLIP RN252 CLIP RN443 N2-088_375_3-inch_glass-and-glass_corner_at-drywall.dxf 34

35 RN419 RN252 CLIP RN252 CLIP RN419 N2-089_375_4-inch_glass-and-glass_corner_at-drywall.dxf RN445 RN252 RN252 CLIP CLIP RN445 N2-090_375_5-inch_glass-and-glass_corner_at-drywall.dxf 35

36 RN417 RN255 RN252 RC306 RN417 N2-091_375_2-inch_door-and-glass_corner.dxf RN443 RN255 CLIP RN252 RC306 CLIP RN443 N2-092_375_3-inch_door-and-glass_corner.dxf 36

37 RN419 RN255 CLIP RN252 RC306 CLIP RN419 N2-093_375_4-inch_door-and-glass_corner.dxf RN445 RN255 RN252 CLIP RC306 CLIP RN445 N2-094_375_5-inch_door-and-glass_corner.dxf 37

38 RN417 RN252 RN252 RC306 RN417 N2-095_375_2-inch_glass-and-glass_corner.dxf RN443 RN252 CLIP RN252 RC306 CLIP RN443 N2-096_375_3-inch_glass-and-glass_corner.dxf 38

39 RN419 RN252 CLIP RN252 RC306 CLIP RN419 N2-097_375_4-inch_glass-and-glass_corner.dxf RN445 RN252 RN252 CLIP RC306 CLIP R N445 N2-098_375_5-inch_glass-and-glass_corner.dxf 39

40 RN /2" 1-1/2" RN355 RN355 N3-001_487_1.5-inch_door-head_at-drywall.dxf See also N3-002 N3-002_487_1.5-inch_door-head.dxf See also N3-001 RN355 RN /2" 1-1/2" N3-003_487_1.5-inch_hinge-jamb.dxf N3-004_487_1.5-inch_strike-jamb.dxf 40

41 RN355 RN354 RN354 RN /2" N3-005_487_1.5-inch_strike-jamb_at-glass.dxf See also N /2" N3-006_487_1.5-inch_hinge-jamb_at-glass.dxf See also N3-005 RN /2" 1-1/2" RN352 RN352 N3-007_487_1.5-inch_head_and_jamb.dxf See also N3-008 N3-008_487_1.5-inch_head.dxf See also N3-007 RN350 RN351 RN351 RN /2" 1-1/2" RN361 N3-009_487_1.5-inch_horizontal-mullion.dxf N3-010_487_1.5-inch_sill_at-drywall_one-snap.dxf See also N3-011, N3-016, N

42 RN358 RN358 RN350 RN351 RN /2" 1-1/2" RN356 N3-011_487_1.5-inch_sill_at-drywall_two-snap.dxf See also N3-010, N3-016, N3-022 N3-012_487_1.5-inch_transom-bar.dxf RN /2" RN352 RN354 Rn425 N3-014_487_1.5-inch_cased-head_and_jamb_and_sill.dxf 1-1/2" N3-013_487_1.5-inch_vertical-mullion.dxf RN /16" Rn425 RN350 RN /2" RN355 RN320 N3-015_487_2-inch_door-head.dxf N3-016_487_1.5-inch_sill_one-snap.dxf See also N3-010, N3-011, N

43 RN417 RN417 RN355 RN /16" 1-15/16" N3-017_487_2-inch_hinge-jamb.dxf N3-018_487_2-inch_strike-jamb.dxf RN417 RN417 RN355 RN353 RN355 RN /16" 1-15/16" N3-019_487_2-inch_strike-jamb_at-glass.dxf See also N3-020 N3-020_487_2-inch_hinge-jamb_at-glass.dxf See also N

44 RN358 RN /16" RN /2" RN321 RN352 RN417 N3-021_487_2-inch_head_and_jamb.dxf N3-022_487_1.5-inch_sill_two-snap.dxf RN417 RN350 RN351 Rn417 RN350 RN /16" 1-15/16" RN354 N3-023_487_2-inch_horizontal-mullion.dxf N3-024_487_2-inch_sill_at-drywall_one-snap.dxf See also N3-025, N3-030, N3-036 Rn417 RN350 RN351 RN417 RN358 RN /16" RN /16" RN260 RN360 N3-025_487_2-inch_sill_at-drywall_two-snap.dxf See also N3-024, N3-030, N3-036 N3-026_487_2-inch_transom-bar.dxf 44

45 RN417 RN352 RN353 RN417 RN /16" 1-15/16" N3-027_487_2-inch_vertical-mullion.dxf N3-028_487_2-inch_cased-head_and_jamb_and_sill.dxf RN443 3" RN417 RN350 RN /16" RN355 RN321 N3-029_487_3-inch_door-head.dxf N3-030_487_2-inch_sill_one-snap.dxf See also N3-024, N3-025, N

46 RN443 RN443 RN355 RN355 3" 3" N3-031_487_3-inch_hinge-jamb.dxf N3-032_487_3-inch_strike-jamb.dxf RN443 RN443 RN355 RN352 RN355 RN352 3" 3" N3-033_487_3-inch_strike-jamb_at-glass.dxf See also N3-034 N3-034_487_3-inch_hinge-jamb_at-glass.dxf See also N

47 RN417 RN358 RN358 RN /16" 3" RN321 RN443 RN352 N3-036_487_2-inch_sill_two-snap.dxf See also N3-024, N3-025, N3-030 N3-035_487_3-inch_head_and_jamb.dxf RN443 RN350 RN351 RN443 RN350 RN351 3" 3" RN352 N3-038_487_3-inch_sill_at-drywall_one-snap.dxf See also N3-039, N3-044, N3-050 N3-037_487_3-inch_horizontal-mullion.dxf RN443 RN350 RN351 RN443 RN358 RN358 3" RN314 3" RN355 N3-039_487_3-inch_sill_at-drywall_two-snap.dxf See also N3-038, N3-044, N3-050 N3-040_487_3-inch_transom-bar.dxf 47

48 RN443 RN303 RN352 RN352 RN443 3" 3" N3-041_487_3-inch_vertical-mullion.dxf N3-042_487_3-inch_cased-head_and_jamb_and_sill.dxf RN443 4" RN443 RN350 RN351 RN355 3" RN322 N3-043_487_4-inch_door-head.dxf N3-044_487_3-inch_sill_one-snap.dxf See also N3-038, N3-039, N

49 RN419 RN419 RN355 RN355 4" 4" N3-045_487_4-inch_hinge-jamb.dxf N3-046_487_4-inch_strike-jamb.dxf RN419 RN419 RN355 RN352 RN352 RN355 4" 4" N3-047_487_4-inch_strike-jamb_at-glass.dxf See also N3-048 N3-048_487_4-inch_hinge-jamb_at-glass.dxf See also N

50 RN419 RN443 RN358 RN358 4" RN314 3" RN352 RN322 N3-049_487_4-inch_head_and_jamb.dxf N3-050_487_3-inch_sill_two-snap.dxf See also N3-038, N3-039, N3-044 RN419 RN350 RN351 RN419 RN350 RN351 4" 4" RN352 N3-051_487_4-inch_horizontal-mullion.dxf N3-052_487_4-inch_sill_at-drywall_one-snap.dxf See also N3-053, N3-058, N

51 RN419 RN350 RN351 RN419 RN358 RN358 RN314 4" 4" RN355 N3-053_487_4-inch_sill_at-drywall_two-snap.dxf See also N3-052, N3-058, N3-064 N3-054_487_4-inch_transom-bar.dxf RN419 RN419 RN303 RN352 RN352 4" 4" N3-055_487_4-inch_vertical-mullion.dxf N3-056_487_4-inch_cased-head_and_jamb_and_sill.dxf 51

52 RN445 5" RN355 N3-057_487_5-inch_door-head.dxf RN350 RN351 RN419 4" RN323 N3-058_487_4-inch_sill_one-snap.dxf See also N3-052, N3-053, N

53 RN445 RN355 5" N3-059_487_5-inch_hinge-jamb.dxf RN445 RN355 5" N3-060_487_5-inch_strike-jamb.dxf 53

54 RN445 RN355 RN352 5" N3-061_487_5-inch_strike-jamb_at-glass.dxf See also N3-062 RN445 RN352 RN355 5" N3-062_487_5-inch_hinge-jamb_at-glass.dxf See also N

55 RN445 RN419 RN358 RN358 5" RN314 4" RN352 RN323 N3-063_487_5-inch_head_and_jamb.dxf N3-064_487_4-inch_sill_two-snap.dxf See also N3-052, N3-053, N3-058 RN445 RN350 RN351 RN445 RN350 RN351 5" 5" RN352 N3-065_487_5-inch_horizontal-mullion.dxf N3-066_487_5-inch_sill_one-snap.dxf See also N3-067, N3-071, N

56 RN445 RN350 RN351 RN445 RN358 RN358 RN314 5" 5" RN355 N3-067_487_5-inch_sill_two-snap.dxf See also N3-066, N3-071, N3-072 N3-068_487_5-inch_transom-bar.dxf RN445 Rn445 RN303 5" RN352 RN352 5" N3-069_487_5-inch_vertical-mullion.dxf N3-070_487_5-inch_cased-head_and_jamb_and_sill.dxf 56

57 RN350 RN351 RN445 5" RN324 N3-071_487_5-inch_sill_one-snap.dxf See also N3-066, N3-067,N3-072 RN358 RN358 RN314 RN445 5" RN324 N3-072_487_5-inch_sill_two-snap.dxf See also N3-066, N3-067, N

58 RN355 RN352 N3-073_487_1.5-inch_door-and-glass_corner_at-drywall.dxf 58

59 RN352 RN352 N3-074_487_1.5-inch_glass-and-glass_corner_at-drywall.dxf 59

60 RN355 RN352 N3-075_487_1.5-inch_door-and-glass_corner.dxf 60

61 RN352 RN352 N3-076_487_1.5-inch_glass-and-glass_corner.dxf 61

62 RR /8" N3-077_487_1-way_corner.dxf RR /8" N3-078_487_2-way_corner.dxf 62

63 RR438 RR519 RR517 NS700 N3-079_487_radius_corner.dxf RR313 RR313 N3-080_487_adjustable_corner.dxf 63

64 RR /8" RR444 N3-081_487_3-way_corner.dxf RR /8" RR443 N3-082_487_4-way_corner.dxf 64

65 RN417 RN355 RN352 RN417 N3-083_487_2-inch_door-and-glass_corner_at-drywall.dxf 65

66 RN443 RN355 CLIP RN352 CLIP N3-084_487_3-inch_door-and-glass_corner_at-drywall.dxf 66

67 RN419 RN355 CLIP RN352 CLIP RN419 N3-085_487_4-inch_door-and-glass_corner_at-drywall.dxf 67

68 RN445 RN355 CLIP RN352 CLIP RN445 N3-086_487_5-inch_door-and-glass_corner_at-drywall.dxf 68

69 RN417 RN352 RN352 RN417 N3-087_487_2-inch_glass-and-glass_corner_at-drywall.dxf 69

70 RN443 RN352 CLIP RN352 CLIP RN443 N3-088_487_3-inch_glass-and-glass_corner_at-drywall.dxf 70

71 RN419 RN352 CLIP RN352 CLIP N3-089_487_4-inch_glass-and-glass_corner_at-drywall.dxf 71

72 RN445 RN352 CLIP RN352 CLIP RN445 N3-090_487_5-inch_glass-and-glass_corner_at-drywall.dxf 72

73 RN417 RN355 RN352 RN417 N3-091_487_2-inch_door-and-glass_corner.dxf 73

74 RN443 RN355 CLIP RN352 CLIP RN443 N3-092_487_3-inch_door-and-glass_corner.dxf 74

75 RN419 RN355 CLIP RN352 CLIP RN419 N3-093_487_4-inch_door-and-glass_corner.dxf 75

76 RN445 RN355 RN352 CLIP CLIP RN445 N3-094_487_5-inch_door-and-glass_corner.dxf 76

77 RN417 RN352 RN352 RN417 N3-095_487_2-inch_glass-and-glass_corner.dxf 77

78 RN443 RN352 CLIP RN352 CLIP RN443 N3-096_487_3-inch_glass-and-glass_corner.dxf 78

79 RN419 RN352 CLIP RN352 CLIP RN419 N3-097_487_4-inch_glass-and-glass_corner.dxf 79

80 RN445 RN352 RN352 CLIP CLIP RN445 N3-098_487_5-inch_glass-and-glass_corner.dxf 80

81 SolutionsII Guide Typical Specifications Details GUIDE SPECIFICATION Manufacturer: Raco Interior Products, Inc Silber Road Houston, Texas voice toll free voice fax SECTION INTERIOR ALUMINUM DOORS, DOOR FRAMES, AND STOREFRONT FRAMING (SOLUTIONS II SYSTEM) ************************************************************************************************************************ This guide specification has been prepared by RACO Interior Products, Inc. in printed and electronic media, as an aid to specifiers in preparing written construction documents for interior applications for aluminum door frames, sidelight framing, storefront framing, and aluminum and glass doors. Edit entire master to suit project requirements. Modify or add items as necessary. Delete items that are not applicable. Words and sentences within brackets [ ] reflect a choice to be made regarding inclusion or exclusion of a particular item or statement. This section may include performance, proprietary, and descriptive type specifications. Edit to avoid conflicting requirements. Editor notes to guide the specifier are included between lines of asterisks to assist in choices to be made. Remove these notes before final printing of specification. This guide specification is written around the Construction Specifications Institute (CSI), Section Format standards references to section names and numbers are based on MasterFormat 95. For specification assistance on specific product applications, please contact our offices above or any of our local product representatives throughout the country. RACO reserves the right to modify these guide specifications at any time. Updates to this guide specification will be posted to the manufacturer s web site and/or in printed matter as they occur. Raco makes no expressed or implied warranties regarding content, errors, or omissions in the information presented. ************************************************************************************************************************ PART 1 GENERAL 1.1 SUMMARY A. Related Documents: 1. Provisions established within the General and Supplementary Conditions of the Contract, Division 1 _ General Requirements, and the Drawings are collectively applicable to this Section. ************************************************************************************************************************* Edit the "Section Includes" paragraph to briefly describe the content of the section. After editing section, refer back to this paragraph to verify no conflicts occur. ************************************************************************************************************************ 81

82 SolutionsII Guide Typical Specifications Details B. Section Includes: 1. Aluminum door frames for interior use. 2. [Aluminum door frames with sidelight frame components for interior use.] 3. [Aluminum OfficeFronts framing system for interior use.] 4. [Aluminum and glass doors for interior use.] C. Related Sections: 1. [Section Wood Doors.] 2. [Section Plastic Doors.] 3. [Section Door Hardware.] 4. [Section Glazing.] 1.2 SUBMITTALS ************************************************************************************************************************ Include submittal requirements below which are consistent with the scope of the project and extent of work of this section. Only request submittals which are necessary for review of design intent. Do not request submittals if drawings sufficiently describe the products of this section or if proprietary specifying techniques are used. The review of submittals increases the possibility of unintended variations to drawings. ************************************************************************************************************************ A. Submit under provisions of Section B. Product Data: Submit for door, sidelight and OfficeFronts frames. 1. Include information for factory finish, glazing gaskets, accessories and other required components. 2. Include color charts for finish indicating manufacturer's standard colors available for selection. C. Shop Drawings: Submit schedule indicating opening identification number, frame types, dimensions, swing, label, and hardware requirements. Use same reference numbers for openings as Contract Drawings. D. Include elevations and details indicating frame types, profiles, conditions at openings, methods and locations of anchoring, glazing requirements, hardware locations, and reinforcements for hardware, details of connections to special construction and other custom features. E. Samples: Submit following: 1. Samples indicating quality of finish in selected colors on alloys used for Work. 2. Where normal color and texture variations are expected, include additional samples to show range of such variation. F. Informational Submittals: Submit manufacturer's instructions. 1.4 QUALITY ASSURANCE ************************************************************************************************************************ Include quality assurance requirements below which are consistent with the size and scope of the project and extent of work of this section. Only request qualification statements you intend to review, and which are necessary to establish qualifications of the product, manufacturer, or installer. ************************************************************************************************************************ A. Single Source Responsibility: Provide aluminum frames, aluminum and glass doors, and accessories produced by a single manufacturer for each type of product indicated. B. Manufacturer s Qualifications: Manufacturer shall demonstrate previous experience in manufacturing of interior aluminum door and OfficeFronts framing for a period of not less than 10 years on comparable sized project. C. [Fire and Smoke Rated Assemblies: 1. Where fire-rated openings are scheduled or required by authorities having jurisdiction, provide fire-rated aluminum frames that have been tested and certified to meet the requirements of UBC 7.2 Fire Test of Door Assemblies for specified exposure by an agency acceptable to governing authorities. 2. Provide labels permanently fastened on each fire rated frame and door that are within size limits established by NFPA and the testing authority.] 82

83 SolutionsII Guide Typical Specifications Details 1.5 DELIVERY, STORAGE, AND HANDLING A. Deliver frames and doors in cartons to provide protection during transit and storage at project site. B. Inspect frames and doors upon delivery for damage. 1. Repair minor damage to pre-finished products by means as recommended by manufacturer 2. Replace frames and doors that cannot be satisfactorily repaired. C. Store frames and doors at project site under cover and as near as possible to final installation location. Do not use covering material that will cause discoloration of aluminum finish. 1.6 ENVIRONMENTAL REQUIREMENTS A. Do not begin installation of frames or doors until area of work has been completely enclosed and interior is protected from the elements. B. Maintain temperature and humidity in areas of installation within reasonable limits, as close as possible to final occupancy. If necessary, provide temperature control and ventilation to maintain required environmental conditions. 1.7 WARRANTY A. Warrant against defects in manufacturing of materials for a period of 2 years from date of substantial completion. B. Warrant framing finish against defects, including cracking, flaking, blistering, peeling, and excessive fading, chalking and non-uniformity in color for a period of 5 years. C. [Warrant aluminum and glass doors for life of door against corner construction failure, causing wracking of door beyond acceptable tolerances.] PART 2 PRODUCTS 2.1 ACCEPTABLE MANUFACTURERS AND PRODUCTS A. Manufacturers: 1. Meet of exceed standards of manufacture, appearance, performance, function, and design, of Raco Interior OfficeFronts by RACO Interior Products, Inc. 2. Substitutions: Comply with provisions of Section B. Acceptable Products: ************************************************************************************************************************ Select from product list below for particular project needs. Include item 1 below if only door frames are required. Delete items a, b, and c if fire rated doors are not required. Include item 2 below if sidelights and storefront framing is required Include item 3 below if aluminum and glass swinging doors are required Include item 4 below if sliding aluminum and glass doors are required. ************************************************************************************************************************ 1. [Interior Door Frames: RACO Solutions II [fixed] [adjustable] throat frames to accommodate wall thicknesses indicated on Drawings; [ceiling height] [ ] height system; with applied full face trim of [1-1/2] [2] [3] [4] [5] inch width. a. [Provide fire rated frames to [20] [90] minute rating complying with UL 10B, ASTM E152, and NFPA 252.]] 2. [Interior OfficeFronts Framing: RACO Solutions II OfficeFronts, fixed throat frames to accommodate wall thicknesses indicated on Drawings; [ceiling height] [ ] height system, with applied full face trim of [1-1/2] [2] [3] [4] [5] inch width.] 3. [Swinging Aluminum and Glass Doors: RACO Series 550, wide stile doors, having [square] [beveled] glazing stops, and EPDM glazing gaskets, [and having ADA compliant bottom rail]. ************************************************************************************************************************ Select item a. below for non-fire rated doors and item b. for fire rated doors. In item c., custom mullion configurations can be specified and should be indicated on the Drawings as to type and locations. Hardware for swinging doors can be specified in e. below, or this sections can be reference to Section for all hardware requirements. ************************************************************************************************************************ 83

84 SolutionsII Guide Typical Specifications Details a. [Provide non-fire rated with adjustable bottom rails for field adjustment.] b. [Provide with 20 minute (without hose stream test) fire rated label, factory glazed with approved clear (wireless) or approved wire glass. c. [Provide with custom horizontal and vertical mullion pattern as indicated on Drawings] d. [Provide complete with the following hardware in [ ] finish: (1) [1-1/2] [2] pair of 4-1/2 x 4-1/2 inch [standard] [ball bearing] butts. (2) Exposed overhead closer, [standard] [slim line] profile. (3) [Latch] [Lock] set to match other devices in project. (4) Flush bolts for inactive leaf of pairs of doors. (5) Balance of hardware as indicated in Section ] 4. [Sliding Aluminum and Glass Doors: Series 2000, Sliding Doors, complete with 2-1/16 inch stiles, 2-1/8 inch top rail, and 3-3/16 inch bottom rail.] 2.2 MATERIALS A. Aluminum: Meeting requirements of ASTM B221, 6063T5 alloy, and as otherwise required to assure compliance with dimensional tolerances and maintain color uniformity. Billets shall be composed of at least 33% recycled aluminum. B. Anchorage Devices, Clips and Fasteners: Manufacturer's standard type, compatible with materials being secured. C. Accessories: As necessary for complete system. 2.3 EXTRUDED ALUMINUM FRAME AND DOOR FABRICATION A. [Utilize adjustable angle vertical mullion for segmented curved OfficeFronts. B. [Utilize reduced profile corner section for 90 degree corners.] C. Assemble all door frames, sidelights, and window units with screws utilizing internal screw spline system, insert into the drywall rough opening, and then attach perimeter flanges. D. Assemble all sidelights and windows without the use of clips. E. Do not exceed maximum size of window or door to meet applicable code requirements. F. Factory pre-machine door frame jambs [and doors] and prepare for hardware, with concealed reinforcement plates, drilled and tapped as required, and fastened within frame with concealed screws. 2.4 FINISHES A. Factory finish extruded frame and door components so that all parts exposed to view upon completion of installation are uniform in finish and color. Exposed surfaces shall be free of scratches and other serious blemishes. B. [Factory Applied Paint Finish: Comply with AAMA(2603)603.8 and AA-DAF-45, factory applied backed enamel coating. 1. Color: [As selected from manufacturer s standard colors] [Custom color to match Architect s sample].] C. Clear Anodized: AA-M12C22A21, etched, medium matte, clear anodic coating. D. [Clean all aluminum surfaces of contaminants and leave ready for field painting per Section ] PART 3 EXECUTION 3.1 EXAMINATION A. Examine project conditions and verify that project is ready for work of this section to proceed. Do not proceed with installation until unsatisfactory conditions have been corrected. B. Verify wall thickness does not exceed manufacturer s recommended tolerances of specified throat size. 84

85 SolutionsII Guide Typical Specifications Details 3.2 INSTALLATION A. Comply with frame and door manufacturer's printed installation instructions and approved shop drawings. Do not attempt installation in areas where wall thickness exceeds tolerances of specified throat size. B. Install frames plumb and square, free from warp or twist, securely anchored to substrates with fasteners recommended by frame manufacturer. Maintain dimensional tolerances and alignment with adjacent work. Ensure joints are hairline tight and surfaces flush with adjacent components. C. Set all doors in correct locations as shown on the drawings, level, square, plumb and in alignment with other work in accordance with the manufacturer's installation instructions and approved shop drawings. D. [Install glass in accordance with Section ] 3.3 ADJUSTING AND CLEANING A. Protect exposed portions of aluminum surfaces from damage by plaster, lime, acid, cement, and other contaminants. B. Touch up marred areas so that touch-up is not visible from a distance of 4 feet. Remove and replace frames that cannot be satisfactorily adjusted. 3.4 PROTECTION A. Protect as required to assure that frames and doors will be without damage until Substantial Completion. END OF SECTION 85

86 SolutionsII RACO Interior OfficeFronts Installation Instructions RACO Interior Products, Inc.

87 The following precautions are recommended to protect the material against damage. Following these precautions will help ensure early acceptance of your products and workmanship. All aluminum materials at job site must be stored in a safe place well removed form possible damage by other trades. Cardboard wrapped or paper interleaved materials must be kept dry. Check arriving materials for quantity and keep record of where various materials are stored. Prevent cement, plaster or other materials form damaging the finish. Protect erected frame with polyethylene or canvas splatter screen. Cement, plaster, terrazzo, other alkaline solutions and acid based materials used to clean masonry are harmful to the finish. If any of these materials come in contact with the aluminum, Immediately remove with water and mild soap. Care must be taken when laying carpet to prevent the backing from scraping against the finished metal. Check shop drawing, installation instructions, architectural drawings and shipping lists to become thoroughly familiar with the project. The shop drawings take precedence and include specific details for the project. Note any field verify notes on the shop drawings prior to installing. The installation instructions are of a general nature and cover most common conditions. All materials are to be installed plumb, level and true. All work should start from bench marks and/or column lines as established by the architectural drawings and the general contractor with guaranteed accuracy. Working from these datum points and lines, determine: The plane of the wall in reference to offset lines provided on each floor. The finish floor lines in reference to bench marks on the building columns. The finished ceiling in reference to bench marks on building columns. All field welding must be adequately shielded to avoid any splatter on glass or aluminum. Results will be unsightly and/or structurally unsound. Advise general contractor and other trades accordingly. Make certain that construction which will receive your materials is in accordance with the contract documents. If not, notify the general contractor in writing and resolve differences before proceeding with work. Be sure you have everything required to begin installation. Sealants must be compatible with all materials with which they have contact, including other sealant surfaces. Consult with sealant manufacturer for recommendation relative to joint size, shelf life, compatibility, priming, tooling, adhesion, etc. Due to varying job conditions, all sealants used should be approved by sealant manufacturer to insure that they will function for conditions shown on instructions and shop drawings. Within this body of instructions fastening means any method of securing one part to another or to adjacent materials. Only those fasteners used within the system and for attaching aluminum frames to the drywall are shown in these instructions. Consult the fastener supplier for proper size and type fasteners used to secure frame (anchors) into concrete. Due to the diversity in state/provincial, local and federal laws and codes that govern the design and application of architectural products, it is the responsibility of the individual architect, owner and installer to assure that products selected for use on projects comply with all applicable building codes and laws. Raco Interior Products exercises no control over the use or application of its products, glazing materials and operating hardware and assumes no responsibility thereof. Final cleaning of exposed aluminum surfaces should be done in accordance with AAMA specifications for anodized aluminum and for painted aluminum. The rapidly changing technology within the architectural aluminum products industry demands that Raco Interior Products reserve the right to revise, discontinue or change any product line, specification or electronic media without prior written notice. Note: Dimensions in parentheses ( ) are millimeters unless otherwise noted. Other metric units shown in this manual are: = meter = kilogram = pascal = kilopascal = megapascal

88 GENERAL NOTES... 2 Solutions II COMPONENTS... 4 DRYWALL FRAMING CONSTRUCTION Solutions II DESCRIPTION AND ROUGH OPENING SIZES DOOR FRAME INSTALLATION TRANSOM DOOR FRAME INSTALLATION SIDELIGHT, BORROWED LIGHT & CLERESTORY CUTTING FORMULAS, ASSEMBLY PROCEDURES, AND INSTALLATION ADJUSTABLE MULLION ASSEMBLY AND INSTALLATION CORNER MULLION ASSEMBLY AND INSTALLATION BUTT GLAZE SPACER INSTALLATION GLAZING NOTES & GLASS SIZES HARDWARE INSTALLATION COLUMN CONSTRUCTION... 39

89 C Beam RN201 RN301 Cased Jamb/Head RN203 RN303 Flat Insert RN207 RN307 Floor Track (FS 5S) RN208 RN308 Sill Double Snap Base RN214 RN314 Head & Floor Track (FS5) RN218 RN318 Floor Track (FS5 Extended Leg) RN219 N/A RN 7DL Glazing Base RN250 RN350 RN 7DL Glazing Snap (use With RN 7DL Base and RN 7M Base) RN251 RN351 RN 5M Wall Jamb/Head RN252 RN352 RN 5D 2" Glazing Insert RN253 RN353 RN5DS 1 1 /2" Glazing Insert RN254 RN354 RN Door Frame RN255 RN355 RN 4S Transom Door Frame Header Insert 1 1 /2" RN256 RN356 RN 7SS Shallow Snap RN258 RN358

90 RN DF Header with Removable Stop RN259 N/A RN 4DS Transom Door Frame Header Insert 2" RN260 RN360 RN 7M Horizontal Mull Base RN261 RN361 Adjustable Mullion RR212 RR412 Mullion Axle RR213 RR /2" Sill Channel RR220 RR420 2" Sill Channel RR221 RR421 3" Sill Channel RR222 RR422 4" Sill Channel RR223 RR423 5" Sill Channel RR224 RR424

91 Corner Mullion Back Cover RR238 RR438 Corner Mullion Face Trim RR517 Used For All Series RR517 Used For All Series Two Pocket Corner Member JD454 RR443 One Pocket Corner Member JR454 RR444 Flat Corner Member JP454 RR445

92 RN Stop used with RN 259 Trim #700 3 /8" x 1 1 /2" Trim Radius 1 1 /2" Trim #716 7 /16" x 1 1 /2" Trim #201 3 /8" x 1 15 /16" Trim Clip #21C Trim #401 3 /8" x 4" Trim 3" 3 /8" x 3" Trim #4TM Scribe Trim 4" Trim 5" 3 /8" x 5" Trim #500 5 /8" x 1 1 /2" Flat Bar Strap 1 /16" x 2" Trim #5TM Scribe Trim 5"

93 1 /4" Top Load Gasket Vinyl Clip for Mitered Corner 3 /8" Top Load Gasket Vinyl Face Clip for Radius Corner 9 /16" Top Load Gasket Vinyl Drill Jig for Solutions II Setting Blocks for 1 /4" to 3 /8" Glass Magnetic Socket for ST351 Screw Setting Blocks for 1 /2" to 9 /16" Glass #6 x 9 /16" Tek Screw Edge Block for Deep Pocket #10 x 1" H.H. Assembly Screw Anchor Clip for Radius Corner with Screws R4 LongPoint Tek Screw Clip for Mitered Corner

94 Butt Glaze Support 1 /4" Glass RN Clip "T".400" x 2" x 3 1 /2" Butt Glaze Support 90 Corner 1 /4" Glass Reinforcement Plate for Parallel Arm Closer or Coordinator Butt Glaze Support 3 /8" Glass Reinforcement for Surface Mounted Regular Arm Closer Butt Glaze Support 90 Corner 3 /8" Glass Spacer Bar for Surface Mounted Parallel Arm Closer and Spacer Bar for Surface mounted Coordinator Comes in Various Lengths RN Clip #1.830" x 2 1 /2" Adjustable Mullion Gasket RN Clip #6.500" x 3" Door Frame Gasket RN Clip #7.500" x 2 1 /2" RN Clip #8.400" x 2" x 2"

95 Solutions II is a interior door frame and glazing system designed to fit over conventional drywall construction. The system is assembled into rough openings left in the drywall and attached to the wall. Solutions II fits over two common drywall throat sizes. They are 3-3/4 and 4-7/8 wall thicknesses. Care should be taken by the drywall installer to keep the wall thickness as close to nominal as possible and never more than 1/8 thicker than nominal. Walls constructed greater than nominal may cause the trim not to sit flat against the drywall. Note the C stud nearest the edge of the rough opening should be reversed so that the open end of the stud is towards the rough opening. This includes the head and sill if they cover drywall. Before installing the frame, confirm the drywall is within tolerance in thickness and that the rough opening is the proper size and plumb. Head Head Jamb Jamb Sill Jamb Shown with 6" Compressions Channel Segments. Use segments at areas where wall is wider than nominal drywall thickness dimensions. Wall will compress up to 1/4"

96 Rough Opening Width is equal to Door Opening Width plus 1-1/2 Rough Opening Height (less than Ceiling Height) is equal to Door Opening Height plus 3/4 Rough Opening Width is equal to Door Opening Width plus Day Light Opening Width of window(s) plus the width of the vertical intermediate(s) plus 1-1/2 Rough Opening Height (less than Ceiling Height) is equal to Door Opening Height plus 3/4 if sidelight is to the finished floor. If sidelight is over drywall at the sill, rough opening is DLO plus 1-1/2. Rough Opening Width is equal to Door Opening Width plus Day Light Opening Width of the windows plus the width of the vertical intermediates plus 1-1/2 Rough Opening Height (less than Ceiling Height) is equal to Door Opening Height plus 3/4 Rough Opening Width is equal to Door Opening Width plus 1-1/2 Rough Opening Height (less than Ceiling Height) is equal to Door Opening Height plus Day Light Opening Height of Transom plus Door Frame Header Width plus 3/4 Rough Opening Width is equal to Day Light Opening Width plus 1-1/2 Rough Opening Height (less than Ceiling Height) is equal to Day Light Opening Height plus 1-1/2 Rough opening tolerances are plus or minus 1/4 All C studs nearest the edges of the rough opening should be reversed so that the open end of the stud is towards the rough opening. The edge of the C studs should be flush with the edge of the drywall and care should be taken that the drywall edge is square and plumb. All attachment screws should be embedded into the drywall. All screws attaching C studs and stud track should not cause the drywall to flare. The drywall thickness should not exceed the nominal wall thickness. This includes head and sill conditions if covering drywall. Cross Section Of Door Frame Jamb Showing Reversed C Stud And Coverage Of Frame Over Drywall

97 (Drywall at the head) (Extra length on the bottom of the jambs for field cutting to fit floor variance) Do not proceed unless the drywall is within tolerance and plumb. Parts list for single door frame: (double frame similar) Door frame header Trim for both sides Door frame hinge jamb (two if double frame) Trim for both sides, one side is factory notched to clear the hinges Door frame strike jamb (none if double frame) Trim for both sides, one side is factory notched to clear the strike Door stop gasket for header and both jambs Corner clips (4-RA108) to connect the header with the jambs Do not attach header at this time Make sure door stop is facing the right direction Adjust the header to its proper height and confirm the door opening height (use temporary screws to hold if necessary) Measure from the rabbet line to the finished floor on each side to determine the exact lengths of the two jambs to accommodate variance in the floor Cut the excess extra length off the bottom of the jambs to fit Plumb vertically Make sure jamb is not rotated in or out Secure to the wall with 1-1/4 drywall screws on both sides of the jamb (screws supplied by others) Top screw within one inch of the top of the jamb Bottom screw within one inch of the bottom of the jamb Intermediate screws every 9 to 12 inches Level the header Make sure header is not rotated in or out Secure header to the jambs using the corner clips (all four corners) Secure the header to the wall using 1-1/4" drywall screws on both sides (screws supplied by others) First screws within one inch of each end Intermediate screws every 9 to 12 inches Plumb vertically Make sure jamb is not rotated in or out Secure to the wall with 1-1/4" drywall screws on both sides of the jamb Top screw within one inch of the top of the jamb Bottom screw within one inch of the bottom of the jamb Intermediate screws every 9 to 12 inches One side of the hinge jamb trim is notched to clear the hinges Cut the extra length off the bottom of the trim to fit the hinge jamb Attach the trim lining up the notches with the jamb cutouts One side of the strike jamb trim is notched to clear the strike plate Cut the extra length off the bottom of the trim to fit the strike jamb Attach the trim lining up the notch with the jamb cutout Attach the head trim between the tops of the jamb trim Repeat the process on the other side

98 Corner Clip RA108 Hinge Back Up Plate Hinge Jamb Trim Butt Hinge 4 1 /2" x 4 1 /2" Attachment Bolt ST181 Strike Back Up Plate Door Frame Gasket Strike Header Hinge Jamb Strike Jamb Header Trim (2 PCS) Jamb Trim (4 PCS) Corner Clips (4 PCS) Door Stop Gasket Drywall screws supplied by others. Hinges, strikeplate, and screws supplied by others.

99 D.O.H. + 3 /4" D.O.W /2" Rough Opening Rough Opening Width = Door Opening Width + 1-1/2" Rough Opening Height = Door Opening Height + 3/4" Jamb, C Stud flush with edge of Drywall and Plumb Header and Sill similar Header Hinge Strike 3 5 Rough Opening Attachment Screws on both sides of each Jamb and Header Screws one inch from each end and spaced 9" to 12" in between Hinge trim both sides Strike trim both sides Header trim both sides Match notches in hinge trim and notch in strike trim to

100 DLO DLO /8" DLO /8" DLO Door frame header and jambs are factory fabricated Transom glazing shapes are factory fabricated Review single door installation instructions Assemble transom window as shown above Place into rough opening. Do not fasten to the wall Insert door frame header into the bottom of the transom window Install door frame jambs per single door instructions Align the transom window with the door frame and attach to door frame head insert Align the entire assembly in the rough opening Attach the entire assembly to the wall

101 DLO + 3/8 DLO + 3/4 Door frame is factory fabricated DLO DLO DLO DLO Wall jamb DLO + horizontal + DLO +1 3/8 Intermediate verticals DLO + horizontal + DLO +1 Floor track cut lengths DLO + intermediate vertical + DLO + 3/4 Trim for the two door frame jambs are included with the door frame. (recommend field cutting to fit) Head trim fits between the two outside jambs DLO + intermediate vertical profile + DLO + intermediate vertical profile + DOW Wall jamb trim fits from top of head trim to bottom Head profile + DLO + intermediate horizontal profile + DLO + sill profile Intermediate vertical mullion fits between head trim and bottom of the sill trim DLO + intermediate horizontal profile + DLO + sill profile Horizontal mull and sill fit between the verticals DLO