GENERAL 1 FEATURES 1 ORDERING INFORMATIONS 1 GENERAL SPECIFICATIONS 2 PRINT COLUMN 2 CHARACTER SIZE 2 OEM CHARACTERS 2 GRAPHICS 2 INTERFACE 2 POWER 2

Size: px

Start display at page:

Download "GENERAL 1 FEATURES 1 ORDERING INFORMATIONS 1 GENERAL SPECIFICATIONS 2 PRINT COLUMN 2 CHARACTER SIZE 2 OEM CHARACTERS 2 GRAPHICS 2 INTERFACE 2 POWER 2"

Dwain Conley
7 years ago
Views:

1 IMPACT MICRO PRINTER MPT-262ⅡA TECHNICAL MANUAL NADA ELECTRONICS, LTD. V

2 CONTENTS GENERAL 1 FEATURES 1 ORDERING INFORMATIONS 1 GENERAL SPECIFICATIONS 2 PRINT COLUMN 2 CHARACTER SIZE 2 OEM CHARACTERS 2 GRAPHICS 2 INTERFACE 2 POWER 2 CONDITIONS 2 RELIABILTY 3 PAPER 3 INK RIBBON CASETTE 3 WEIGHT 3 ATTACHMENT 3 PANEL SWITCH 4 TEST PRINT 4 HEX DUMP 4 FRONT PANEL 5 REAR PANEL 6 HOW TO CHANGE ROLL PAPER 7 HOW TO CHANGE RIBBON CASETTE 8 CAUTIONS 9 MAINTENANCE AND CLEANING 10 WARNINGS 10 ENVIROMENTS 10 GURANTEE 10

3 GENERAL 262ⅡA series are impact journal printer, with JIS Chinese (KANJI) characters inside, OEM and graphic image, red and black printouts. FEATURES * JIS ⅠⅡ KANJI dots font. * SHIFT JIS code KANJI selectable. * OEM characters dot font. * Graphics printable. * 3 varieties of ANK 184 characters font. ORDERING INFORMATIONS MPT-262ⅡA-C-35 K P B Adopted model Interface KANJI optionals Column printable Cutter optionals Model MODEL MPT-262ⅡA ; desk-top type CUTTER optionals None: wo / cutter standard C: w / cutter COLUMN printable Set by DIP SW or selectable by command 35 ; 5 7 dot font 42 ; 7 7 dot font (half dot) KANJI optionals None : wo / KANJI standard K : KANJI set INTERFACE default set P : Parallel CENTRONICS R : Serial RS232C Adopted model None : standard ; DIP selectable to old model A: MP-210 compatible B : PC-9801 type 1

4 GENERAL SPECIFICATIONS 1:printing method 2:dots per line 3:printing rate Shuttle dot matrix 210 dots / line 2.3 line / sec (5 7 dot font) print only PRINT COLUMN 1:ANK 5 7 font 35 col. 2:ANK 7 7 half font 42 3:ANK 8 16 font 26 4:KANJI full 13 5:KANJI shrank 26 CHARACTER SIZE 1:ANK 184 width height mm mm mm 2:KANJI full mm shrank mm OEM CHRACTERS blocks GRAPHICS Data number 4k byte INTERFACE RS232C / CENTRONICS selectable when order POWER 85 to 132V AC, 50 / 60Hz 60W operational 7W idling CONDITTONS 1:operation 2:stock 0 to +50 ; 30% to 90% non-condensing -20 to +70 ; 5% to 95% non-condensing 2

5 RELIABILITY 1:head life 2:MOBF 3:cutter life 100 million strokes / a pin 1.5 million lines MCBF 0.2 million full-cutting PAPER - nomal paper 1:roll paper 76mm 60 35m ( width dia length ) 2:fan-fold 76mm 5 inch 35m (width height length ) 3:paper thick 0.06 to 0.85mm 4:paper weight 52.4g / m2 to 64g / m2 5:P / N paper NR-760 roll paper INK RIBBON CASETTE ERC-23 ( red / black dual colors), 3 / 4 millions characters life WEIGHT 3.9 kg ATTACHMENT 1:ribbon cassette ERC-23 1 pc. 2:roll paper NR roll 3:roll shaft S-7 1 pc. 4:fuse 2A 100V AC 2 pcs. 5:connecter CENTRONICS 1 pc. or DB-25P RS232C 1 pc. 3

6 PANEL SWITCH 1. FEED SWITCH Paper is fed by this switch. Effective in both mode of select or disselect. Set paper without paper jamming, or OFF power and take off paper by pinsette. 2. SELECT SWITCH This switch can drive printer off-line by manual. If return to on-line, depress this switch again. Or there is no paper, or printer is out of order. TEST PRINT Operation : ON the power depressing FEED switch. Functions : checking mechanics-unit and inner logic, confirming DIP selection. HEX DUMP Operation : ON the paper by depressing SELECT switch. Functions : Printout HEX code data by bufferful mode by depressing SELECT SWITCH, confirming received data. 4

7 FRONT PANEL PW SEL PAPER OUT Paper shall be fed from this position. 2. SELECT SWITCH Switchover SELECT/DISSELECT mode by depressing this switch, and DIP-SW 1-4 OFF. DISSELECT mode, green LED off and will not received data. 3. POWER LED (red) Blinking when power is ON. 4. SELECT LED (green) On this LED is SELECT mode, OFF this LED is DISSELECT mode. DISSELECT automatically by paper-end. 5. FEED SWITCH Paper feed switch, anytime while SELECT or DESSELECT mode. Remark:RED and GREEN LED blinks while MECHANICS ERROR. 5

8 REAR PANEL SERIAL I/O CONNECTOR RS232C connector 2. PARALLEL I/O CONNECTOR CENTRONICS connector 3. GROUND EARTH Cabinet earth plug. 4. FUSE V AC power line, 2A fuse only. 5. POWER V AC supplyable. 6

9 HOW TO CHANGE ROLL PAPER Open top cover 1 then 2 as below figure, insert shaft into roll, then set to paper-holder carefully. 1 2 Insert paper and feed by FEED SWITCH, then pass through paper-out of top cover. Completion of setting, change LED from RED to GREEN by SELECT SWITCH. 7

10 HOW TO CHANGE RIBBON CASETTE Open top cover 1 then 2, pull up the edge as figure below. 2 1 Stretch ribbon tape by winding knob as figure below. Set cassette correctly as figure below. Stretch tape by manual or by FEED switch. 8

11 CAUTTIONS 1. Do not print without paper and ribbon cassette. 2. ON the power, it will return head to default automatically. 3. OFF the power, then take off jammed paper by pin carefully. 4. Roll paper must be used our recommended only. 5. Never ON-OFF power repeatedly at short interval. 6. Do not bundle printer-line to other cables. It may be damaged by noises. 7. Clean the printer regularly. 8. Do not set at the place of iron-dusty or dusty. 9. In use of fan-hold paper, it will not print correctly at the position of 8mm from the sewing-line, sometimes. 10.TEST PRINTING by depress FEED SWITCH and ON the power, which shows contents selected by DIP SWITCH. 11.CUTTER mode: drive cutter by FEED SWITCH at disselect mode, then cut automatically. 12.Lever will be up to arrow direction as figure, at ribbon and paper change time, not to bend Lever. Or dual printing is out of order. 13.Mix-printing of character available. However, each character command shall be set newly one by one, or it will cause printing trouble. 9

12 MAINTENANCE AND CLEANING Mechanics and its unit shall be wiped by alcohol or benjin. Never use thinner, torikuren, keton which will damage plastics. Wipe dust by vacuum cleaner. Regular checking : every 3 months or half million.lines printing. WARNINGS 1. Paper jam: never drive jammed paper off, which break mechanics. 2. RED/GREEN LED blinking: OFF and ON power at 5 seconds interval. ENVIROMENTS 1.Do not set at the place of iron-dusty or dusty, where it causes damages of mechanism, gears, etc,. 2.Do not bundle signal line cable with hi-power cable, as V AC cable, to escape from noise trouble. 3. Be care of circumstance, especially chemical conditions. Mechanics has touch point inside, some chemical as SILICONE will cause troubleness. 4. GROUND line shall be set without fail, to escape from hi-statistic voltage on printer. 5. In case of hi-condensity, it will be operated after the clearance of condensing. GURANTEE NADA s obligations and liabilities under the foregoing grantee are limited to repair or replacement of the products without charge, provided it is mailed prepaid or air freight prepaid to NADA ELECTRONICS, Ltd., Overseas Division, , Shiba, Minato-ku, Tokyo 108 JAPAN. A charge is made for repairing after the expiration of grantee. NADA ELECTRONICS, Ltd. grantees the model of type printer series against the defects in material and workmanship for a period of 60 days from the date of shipment to end customer directly. This is a limited grantee to its terms. This grantee is void if the products has been altered, misused, taken apart or otherwise abused. This grantee is effective to the customer who bought product directly from us. Other customers or buyers shall ask for grantee terms to those who sell products,,, agents, distributors, importers, etc,. In no event shall NADA be liable for claims based upon breach of express or implied grantee or negligence or any other damages whether direct, immediate, foreseeable, consequential or special or for any expenses incurred by reason of the use or misuse, sale or fabrications of products which do not confirm to the terms and conditions of this contract. 10

User's Manual. Metapace L-1. Label Printer Rev. 1.00

User's Manual. Metapace L-1. Label Printer Rev. 1.00 User's Manual Label Printer Rev. 1.00 Table of Contents Manual Information & Usage Precautions 3 1. Content Confirmation 6 2. Product Part Names 7 3. Installation & Usage 9 3-1 Power Connection 9 3-2 Interface