Fuller Industries, LLC CUSTOM BRUSH. Division

Transcription

1 Fuller Industries, LLC CUSTOM BRUSH Division B a k e r y M a i n t e n a n c e

2 SENTRY SERIES-CONVEYOR CLEANING BRUSHES Designed specifically to eliminate build-up and carry-over on wire rod cooling conveyor systems. An affordable approach to reducing your bakery conveyor cleaning problems. Two brush assemblies are recommended for each conveyor (one over/one under). Continuous cleaning action keeps rods free of all foreign matter. Cleans conveyor while it operates FEATURES: Zero clearance mounting clips Quick change mounting brackets No separate power drive needed Easy to install Easy to clean (resists bacteria growth) Easy to refill Optional bolt mounting for rigid application Maintenance free Available from stock Color coding available red, green, white and black ORDERING INFORMATION 8A Normal brushing action,.012 crimped red nylon, 3-1 2" outside diameter. 28 long. 8A Heavy brushing action,.018 crimped white nylon, 3-1 2" outside diameter. 28 long. 8A A Normal brushing action,.012 crimped white nylon, 3-1 2" outside diameter. 28 long. Extra-Heavy brushing action,.028 crimped green nylon, 3-1 2" outside diameter. 28 long. 8A Extra-Heavy brushing action,.028 crimped black nylon, 3-1 2" outside diameter. 28 long. 8A Extra-Heavy brushing action,.028 crimped green nylon, 1/2" outside diameter. 36 long. 8A Extra-Heavy brushing action,.028 crimped white nylon, 4" outside diameter. 28 long. Brushes supplied in standard 28" lengths. Coiled to fit 1/2-inch diameter shaft. Can be cut to fit individual needs. Mounting accessories available from stock. This brush can be compressed or expanded to fit 11" to 29" conveyors.

3 SENTRY SERIES-CONVEYOR CLEANING ACCESSORIES SHAFT 9C Polished steel shaft, 36" in length, 1/2" in diameter. 44 shaft available upon request EYE BOLT BEARING SET 9C Bearing hanger for stationary shaft installation. Bronze bushing. Complete with hex nuts. 1/2" inside diameter. MOUNTING BRACKET SET 9C Universal mounting bracket. Predrilled. Complete with nuts, bolts and washers. Use with 9C eye bolt bearing. ZERO CLEARANCE CLIP SET 9C Two wire clips formed to secure a Sentry Brush to a 9C shaft. For standard mount use: 9C C C C

4 SPECIFIC BAKERY CLEANING BRUSHES THE GUARDSMAN Conveyor Cleaning Kit Continuous cleaning without production interruptions. Clean both sides of your conveyor as it operates. Fits all rod conveyors. Easy installation, no separate power drive required. Shafts and mounting hardware included in kit. No drilling, tapping or cutting needed. Fits on 1/2" shaft. 8A A DIMENSIONS Kit, 2 brushes, 3-1 2" x 36" w/mounting hardware.028 crimped green nylon Refill, brush only 3-1 2" x 36" Keep your oven band free of build-up. Manual cleaning of band eliminated with aggressive cleaning action of wire brush. Fits on 4" shaft. OVEN BAND CLEANING BRUSH 8A A DIMENSIONS Steel wire coil brush 8" x 39".010 oil tempered steel wire 8" x 48" * Can be customized to meet your specific oven band requirements. Remove sesame seeds from bun pans effectively. Brush is designed to agitate seeds from pans upper surface. Once dislodged, seeds may be easily carried off by a vacuum system. May also be used for dusting or applying glazed finishes on bakery items. Fits 1" shaft. May be used on Kraft Tandem 550 machines. BUN PAN BRUSH 8A DIMENSIONS Nylon, steel backing 10" x 22".014 crimped white nylon

5 FULLERGRIPT COIL BRUSHES CLOSE WOUND COIL OPEN WOUND COIL Custom Coil Brushes are used for: Bun Pan Brush Greasing Pans Proffer Box Brush Washing Pans Conveyor Brushers Coating Pans Dusters Glazing Brush Dough Brush Muffin Tin Brush COIL BRUSHES Can be custom designed for your application and mounted on your core. Replacement coil brushes are also available for mounting at your location. Whatever your custom brush need, Fuller can design a brush for you. Choose from our wide selection of backing and fill materials to develop an efficient, quality brush for all of your custom brush applications. When Fuller Brush originated the FULLERGRIPT design, a revolutionary brush making process was created. This process provided an economical means of incorporating brush technology into a wide range of modern commercial applications. By winding Brush Strip on a mandrel or shaft, a coil brush is produced. Brush density can be varied by your choice of backing size. The amount of fill material increases proportionately with the size of the backing. The lead of the coil (distance between wraps), affects the working surface of the brush and its performance. Consistent or continuous brush to work surface contact requires a close wound coil (no lead), while an open lead is recommended when working with aggregate, grain or debris. AVAILABLE BACKING MATERIALS Plated steel, stainless steel, aluminum. AVAILABLE FILL MATERIALS Nylons, polypropylene, steel wire, stainless steel wire. Additional material available upon request. OPEN LEAD WHICH TYPE CLOSED LEAD LEAD (SPECIFY SPACING) TO INSURE THE BEST BRUSH PRODUCT FOR YOUR APPLICATION, BE SURE TO INCLUDE THE ESSENTIAL DATA. Use our Quick Quote Forms made available on the Internet

6 CUSTOM DESIGN FULLERGRIPT DISPOSABLE COIL BRUSHES Custom Made Oven Belt Cleaning Brushes can be designed using carbon steel wire or stainless steel wire, available in wire sizes diameter. Our brushes are efficient and will keep your oven belt cleaner to eliminate any manual labor. Conveyor Brushes made to order with a wide range of synthetic fill materials. Brush density can be close wound wide face brush with a smooth, even appearance to an open spiral brush which will have an auguring effect. Driven conveyor brushes typically operate in the opposite direction of the conveyor path. SCREWS TO ATTACH CORE TO HUB HUB FITTED WITH STANDARD KEY WAY BRUSH WOUND ON DISPOSABLE CORE SET SCREWS TO ATTACH HUB TO SHAFT Brush face should be wide enough to overlap each side of the belt surface by 1 to ensure complete coverage. Brush lengths available from Disposable Coil Brush Assemblies are designed for many hours of trouble free service. Easy to install and eliminates down time, improves quality, productivity and safe operating. Brushes are mounted to a thin wall steel core available in 4 or 6 diameter. Hub sets are available to fit the core. Let Fuller Brush help custom design the brush to fit you application. Call for assistance on your brush design.

7 CLEANING ACCESSORIES BACTERIA-FREE NYLON No concealed surfaces to harbor bacterial growth. Nylon fill permanently anchored in stainless steel backing. Will not shed or load up in fine dust. Especially useful any place food is prepared. COLOR LENGTH TRIM white, 9" 2-3 4".010 crimped nylon CHEMICAL RESISTANT BRUSH Long lasting structural foam plastic block is moisture resistant and odor free. Green staple set fill remains stiff for better scrubbing even when wet. Resistant to water, oil, grease and common solvents. Durable, sanitary, odor-free and easy to clean. LENGTH TRIM 4L-238 8" 1-7/8" 4L " 1-7/8" CARPET/UTILITY BRUSH Resillient bristles are durable enough to stand up to any tough scrubbing or stain removal job. The end of the brush can be used to scrape away really stubborn grime. LENGTH /4" HAND N NAIL BRUSH Tufted on both sides of the block. Three rows of short, stiff nylon bristles for scrubbing away stubborn dirt, six rows of long softer nylon bristles for regular hand and nail cleaning. Durable plastic block with convenient hang-up hole " LENGTH

8 SCRUB BRUSHES/HANDLES & ACCESSORIES DUAL SURFACE DECK SCRUB BRUSH Advanced approach to scrubbing floors. Dual surface brush face allows cleaning from a stand up or horizontal position. Durable plastic block with crimped plastic bristles for aggressive cleaning ability. Use with a threaded handle. Polypropylene fill material. LENGTH TRIM " 1-3/4" HEAVY-DUTY TRUCK & WINDOW WASHING BRUSH A rugged, plastic block densely filled with extra soft bristles. Retains soapy water for better washing action. Unique construction includes a built-in water jet for use with fountain handle (Product No. 7C-201). Perfect for washing glass, plastic and painted surfaces. Will not scratch. Accepts threaded handles. LENGTH TRIM " 2-1/2" EXTENSION HANDLE Threaded steel handle that adjusts to any length from 29" to 52". LENGTH END "-52" plastic thread

9 SCRUB BRUSHES/HANDLES & ACCESSORIES FLARED SCRUB BRUSH Durable chemical resistant polyester fill will not scratch surfaces. Flared bristles allow easy scrubbing of tile, grout, corners and shower tracks. Sturdy, structural foam block. Can be used as a hand scrub brush or with an 808 extension handle for extra reach. LENGTH TRIM 204C 7" 2-1/2" FLOOR/WALL GROUT BRUSH Durable polypropylene fill. Tough enough to clean. Gentle enough to prevent scratching surfaces. V trimmed bristles fit narrow or wide grout. Sturdy polypropylene block with toggle connection. Great for wall, shower or floor tile grout. Use with 808 extension handle or any threaded handle. LENGTH TRIM 294C 9" 1" FOUNTAIN HANDLE One piece steel handle with baked green enamel finish. Threaded to fit all standard brushes. Brass fitting fits standard 3/4" garden hose thread. Use with 4117 Truck and Window Washing Brush. LENGTH END 7C " steel thread ROLLED STEEL THREAD One piece steel handle with standard rolled threads. Baked enamel finish provides an attractive appearance and protection against corrosion. Heavy gauge steel provides increased strength and durability. LENGTH DIA. END 7118CB 60" 7/8" steel thread

10 QUICK QUOTATION FORM Date Initiated: Approved By: Date Completed: COIL ONLY 1. Please provide all dimensions in inches. A. Brush Face (OAL) B. Outside Diameter (OD) C. Inside Diameter (ID) D. Lead: Open Close Wound Right Hand Left Hand *Lead is the dimension taken from the center of one coil to the center of the next successive coil. 2. Fill Material: Type Diameter Color Crimped Level 3. Backing: Size Material Type 4. Method Brush will be Fastened to Shaft: Weld Clamps Tangs 5. Operating RPM 6. Bristle Penetration into Object being Brushed: 7. Quantity: Yearly Per Order 8. Customer Name Contact Phone FAX 9. Salesman No. 10. Application: Copy, fill out and fax to FULLER CUSTOM BRUSH DIVISION

11 QUICK QUOTATION FORM Date Initiated: Approved By: Date Completed: COILED BRUSH MOUNTED ON CORE (WITHOUT SHAFT) 1. Please provide all dimensions in inches. A. Brush Face (OAL) B. Outside Diameter (OD) C. Inside Diameter (ID) D. Lead: Open Close Wound Right Hand Left Hand *Lead is the dimension taken from the center of one coil to the center of the next successive coil. 2. Fill Material: Type Diameter Color Crimped Level 3. Backing: Size Material Type 4. Method Brush will be Fastened to Core: Weld Clamps Tangs 5. Please provide all core dimensions in inches. H. Core Length I. Core Outside Dia. J. Core Inside Dia. 6. Core Material/Type: Steel Aluminum Stainless Steel Welded Seam Seamless DOM Wall Thickness 7. End Plates: Inside Dia. Material Key Way Set Screws *Be sure to specify if each end is the same or if they are machined differently. A sketch would be helpful. 8. Customer Name Contact Phone FAX 9. Salesman No. 10. Application: Copy, fill out and fax to FULLER CUSTOM BRUSH DIVISION

12 QUALITY PRODUCTS FOR PROFESSIONAL BAKERY MAINTENANCE SINCE 1906 CUSTOM BRUSH Fuller Industries LLC Custom Products Division One Fuller Way Great Bend, KS USA CANADA Fax: Bakery Maintenance Brochure 2015 rev