CLOUD MANAGED WIFI OUTDOOR ACCESS POINT 300MPBS WL-APO2G USER MANUAL

Transcription

1 CLOUD MANAGED WIFI OUTDOOR ACCESS POINT 300MPBS WL-APO2G USER MANUAL

2 REV.1216

3 Thanks for choosed our product INDEX CHAPTER 1 Mode instruction 1.1 Router Mode 1.2 HotSpot Mode 1.3 Universal Repeater Mode 1.4 Wireless ISP mode CHAPTER 2 Launch and login CHAPTER 3 Wireless connection CHAPTER 4 Working mode setting 4.1 Quickly set up configure device 4.2 Gateway mode configuration 4.3 Wifi repeater configuration 4.4 AP Mode 4.5 WISP CHAPTER 4 Advance setting 5.1 System Status GHz Wireless 5.3 Network Setting 5.4 Management 5.5 Upgrade firmware CHAPTER 6 Specification CHAPTER 7 The Failure phenomenon and solution 3

4 CHAPTER 1 MODE INSTRUCTION 1.1 Router Mode Device can get through ISP/ADSL modem get wired access to fullfil wifi coverage. Connecting type can be PPPOE,PPTP,Dynamic IP and Static IP. internet ISP / ADSL / MODEM ROUTER 1.2 HotSpot Mode Turn PoE switch wired access to wireless network emmission,sharing network,it s the main mode of hotels,office and tenement layout. 4

5 1.3 Universal Repeater Mode Repeat distal wifi signal,sharing local WLAN. Router/Switch. 1.4 Wireless ISP mode Wireless ISP client get wireless connecting to wireless base station to fullfil WLAN sharing. The equipment is wireless WAN connection type can be PPPoE,Dynamic IP and Static IP. 5

6 CHAPTER 2 LAUNCH AND LOGIN 1. Choosing power supply mode,choose matched mode based on your local network environment; 2. Computer network IP set as manual setting IP add. or automatically getting IP add. Manual setting IP add. of wireless connecting as followings: Configuration PC local connecting IP add. is X(X is 2-252),get outdoor omni AP as same network segment, subnet mask is as newxt image shows: 6

7 CHAPTER 3 WIRELESS CONNECTION 1. If connecting device via wireless,it should do as step 2. As next image shows, click right-hand button to choose applicable wireless connection,default SSID is Wireless AP,code is ,click top left refresh network list,the wireless network that searched out will be shown at right side like next image shows, choose the network that you want to connect in,input password to fullfil wireless connecting. 7

8 3. Use IE explorer visit it will popup the login in entering, default entering user name: admin password: admin CHAPTER 4 WORKING MODE SETTING 4.1 Quickly set up configure device Once login web will get as newxt image shows, you will see the basic info. of this device, such as SSID, working mode, channel, software version, hardware version, systemrunning time, etc. then configuration can be done by your own. Default mode is AP mode, quickly setting to configure these devices is as followings. 8

9 4.2 Gateway mode configuration Entering quickly-setting page,then choose ADSL as following next image shows, choosing dynamic IP or PPPOE(ADSL),then you can change SSID, channel, key, etc. Dynamic IP customer: In WAN settings choosing dynamic IP, after changing wireless settings and click application, choose to confirm in the popup interface. PPPOE user: In WAN settings choose ADSL, then input correct user name and password and apply. After patient waiting for system restart, set up computer s IP add. to automatically get, then you can connect in internet. 9

10 4.3 Wifi repeater configuration a. Login the Web management page, click Repeater Mode, then Scan AP b. Select the AP s SSID want to bridge, take SR G for example. c. input the AP s key, and apply changes d. In Repeater Mode, the SSID is disable in default setting, it work as Station;if need SSID broadcast in this mode, just manual to change under Advanced Settings,click sure in this part to finish the repeater operation mode setting After this step, can click the Device status to check the status of this Wireless AP. And it will show Wireless AP s LAN Interface, WLAN status and Sigbal Strength. 10

11 4.4 AP Mode Click wifi coverage as newxt image shows, Plug and Play to transmit wireless signal for wireless end users form wired networking. In this part,user can mark the AP s location and name for easy problem checking. Then can change SSID, Key, Channel as request. Waiting for system reboot,once finished, do as chart 5 shows, set computer s IP address as automatically get, then you can use internet normally. 11

12 4.5 WISP In this operation mode, user should confirm the WAN access type at first, then set the SSID, key, Channel as request. CHAPTER 5 ADVANCE SETTING 5.1 System Status Click Advance Settings, will show system status, such as firmware version, System uptime. 12

13 GHz Wireless In this part, use can scan AP s SSID, disable or enable AP s SSID, modify Channel, Security. 5.3 Network Setting LAN Interface Setup mainly showed as follow 13

14 5.4 Management In this part, user can set Time zone, show Log info, upgrade firmware, change login user name and password; 5.5 Upgrade firmware After finish firmware upgrade, pls click Save/Reload Settings, then reset settings to default. 14

15 CHAPTER 6 SPECIFICATION Item Transmission rate Built-in MIMO antenna Parameters 300Mbps Built-in 5dbi omni antenna Function <10W Power adapter Size (mm) <12V(POE 24V)/1A) 260L x 87W x 54H Weight (g)

16 LED light Power Button: Always light means function well Wifi simbol: Twinkle means 2.4G signals functions well LAN: Always light means LAN port connecting well WAN: Always light means LAN port connecting well Facility port 2 x 10/100Mbps Rj45 port (support 12-24V POE power supply) 1 x reset button,recover factory defalt using 1 x DC Jack, 12V local power supply 16

17 CHAPTER 7 THE FAILURE PHENOMENON AND SOLUTION Failure phenomenon Failure phenomenon Can t land to Wireless AP through Web page Wireless AP can t connect with AP Can t scan the wireless AP The connection of Wireless AP and AP is success, but the computer can t share internet Solution Pls make sure the PoE module connection is right. POE Port connect with AP, LAN port connect with computer Pls check the IP address of computer and Wireless AP to see whether they are in same networking segment, The method is click start - Run input cmd ping to test the Wireless AP connectivity. Reset Wireless AP and load it again; Pls make sure the IP address is not occupied by other device in Wireless AP s networking; Check computer and cable problem, recommend to use 10/100M UTP unshielded cable; Clean up Arp binding from Start - Run input cmd arp d Clean the IE Brower s temporary files and Cache file Try to scan the avaliable wireless networking again, Make sure the Wireless AP s wireless standard 1b/g/n, 2.4G is correct The Security and passwords are matched between Wireless AP and AP The signal strength of AP is too weak to connect, should be more than -75dBm Scan it several times more. Make sure there are 5G signal existed. Reset the Wireless AP, scan it again after Wireless AP restart Pls Check the computer s IP address and DNS setting. If it is dynamin, set the network card as automatically obtain. If it is static IP, pls contact with ISP for correct IP address and DNS address. 17

18 How to Reset Wireless AP Press the Reset button more than 15 seconds after power on. The Wireless AP will restore factory default after the Wireless AP restart. 18

19

20 Per qualsiasi informazione ed aggiornamento sui prodotti > visita il nostro sito Mach Power è un marchio registrato All Right Reserved