1 Quick Start Guide Cisco Small Business RV 120W Wireless-N VPN Firewall Package Contents Wireless-N VPN Firewall Ethernet Cable Power Adapter Quick Start Guide Documentation and Software on CD-ROM
2 Welcome Thank you for choosing the Cisco Small Business RV 120W Wireless-N VPN Firewall. The Cisco RV 120W provides secure, high-speed wireless network access and advanced security features for your small business. This guide describes how to physically install your Cisco RV 120W, start the Setup Wizard, and launch the web-based Cisco RV 120W Configuration Utility. 1 Before You Begin Before you begin the installation, make sure that you have the following equipment and services: Required Functional Internet Connection (Broadband DSL or cable modem). Ethernet cable for WAN (Internet) connection (provided). PC with functional network adapter (Ethernet connection) to run the Setup Wizard or the configuration utility. The Setup Wizard is supported on Microsoft Windows 2000, Windows XP, Windows Vista, and Windows 7. You must have Microsoft Core XML Services (MSXML) software installed on the PC to run the Setup Wizard. MSXML is available from the following location: The configuration utility is supported on the following web browsers: Microsoft Internet Explorer 6.0 and later Mozilla Firefox 3.0 and later Apple Safari 3.0 or later. Software CD containing the Setup Wizard (provided). Optional Uninterruptible Power Supply (UPS) to provide backup power to essential devices (strongly recommended). Ethernet cables for LAN interfaces to connect additional devices (optional). 2 Cisco Small Business RV 120W Quick Start Guide
3 2 Mounting the Cisco RV 120W You can place your Cisco RV 120W on a desktop or mount it on a wall. Installation Guidelines Ambient Temperature To prevent the device from overheating, do not operate it in an area that exceeds an ambient temperature of 104 F (40 C). Air Flow Be sure that there is adequate air flow around the device. Mechanical Loading Be sure that the device is level and stable to avoid any hazardous conditions. For desktop placement, place the Cisco RV 120W unit horizontally on a flat surface so that it sits on its four rubber feet. Wall Mounting STEP 1 STEP 2 Determine where you want to mount the unit and install two screws (not supplied) that are 2-7/16 in. apart (approximately 61 mm). Mounting screws should have a head that is approximately 5.5 mm in diameter and 2 mm deep, with a shaft that is at least 15.5 mm long and approximately 3.5 mm wide. (Depending on your mounting surface, you might require shorter or longer screws, or drywall anchors.) Do not mount the screw heads flush with the wall; the screw heads must fit inside the back of the unit. With the back panel pointing up (if installing vertically), line up the unit so that the wall-mount slots on the bottom of the unit line up with the two screws. 2-7/16 Wall mount slots Cisco Small Business RV 120W Quick Start Guide 3
4 STEP 3 Place the wall-mount slots over the screws and slide the unit down until the screws fit snugly into the wall-mount slots. 3 Connecting the Equipment Cisco recommends that you use the Setup Wizard to connect and configure your Cisco RV 120W. If you do not want to use the setup wizard, skip to the Manually Connecting Your System section on page Cisco Small Business RV 120W Quick Start Guide
5 Using the Setup Wizard Follow these steps to use the Cisco RV 120W Setup Wizard. The Setup Wizard displays on-screen instructions that guide you through the installation, but you may find it useful to refer to this document during installation. NOTE You must connect one PC with an Ethernet cable for the purpose of the initial configuration. After you complete the initial configuration, administrative tasks can be performed using a wireless connection. Starting the Wizard STEP 1 STEP 2 STEP 3 STEP 4 STEP 5 Make sure that all of the network hardware is powered off, including the Cisco RV 120W and cable or DSL modem. Insert the CD that shipped with the Cisco RV 120W into the PC you are using to configure the Cisco RV 120W. The Setup Wizard automatically begins. Click Start to begin the installation. Click the check box to accept the software license agreement and click Next. The Setup Wizard verifies the network adapter on your PC is functional. If you receive an error, view your PC s network connections to make sure the network adapter is working and click Back to test the connection again. Next: If your network adapter is functional and you have not yet connected your hardware, the Install Router window appears. (See Connecting Your Hardware, page 6.) If your network adapter is functional, you have already connected your hardware, and your Internet connection has been detected, the Secure Your Router Settings window appears. (See Configuring Security, page 10.) Cisco Small Business RV 120W Quick Start Guide 5
6 Connecting Your Hardware STEP 1 You should have an Ethernet cable connecting your PC to your current cable or DSL modem. Unplug one end of the cable from your PC and plug it into the port marked WAN on the unit. Click Next. STEP 2 Connect one end of a different Ethernet cable to one of the LAN (Ethernet) ports on the back of the unit. (In this example, the LAN 2 port is used.) Connect the other end to an Ethernet port on the PC that is running the Setup Wizard. Click Next. 6 Cisco Small Business RV 120W Quick Start Guide
7 STEP 3 STEP 4 Power on the cable or DSL modem and wait until the connection is active. Connect the power adapter to the Cisco RV 120W power port. Click Next. CAUTION Use only the power adapter that is supplied with the unit. Using a different power adapter could damage the unit. STEP 5 Plug the other end of the adapter into an electrical outlet. Cisco Small Business RV 120W Quick Start Guide 7
8 STEP 6 On the Cisco RV 120W, push in the ON/OFF POWER SWITCH button. The Setup Wizard searches for the Cisco RV120W. The POWER LED on the front panel lights up green when the power adapter is connected properly and the unit is turned on. Next: If your hardware connection is successful, but the Setup Wizard needs more information about your Internet connection, the Enter Username and Password window appears. (See Entering Login and Internet Connection Information, page 8.) If your hardware connection is successful and the Setup Wizard successfully detects your Internet connection, the Configure Router window displays. (See Configuring Security, page 10.) Entering Login and Internet Connection Information STEP 1 STEP 2 STEP 3 Enter the username and password for your Cisco RV120W. The default username and password are both admin. Click Next. Choose your Internet connection type: Telephone (DSL) Cable broadband I don t know Click Next. The Setup Wizard confirms your Internet connection settings. If it cannot detect or confirm your settings, you might need to provide 8 Cisco Small Business RV 120W Quick Start Guide
9 STEP 4 STEP 5 STEP 6 information about your Internet connection type. You can get this information from your ISP. The types of Internet connections are: Dynamic (DHCP) Your PC receives its IP address from your cable or DSL modem. This address can change. Static IP Connection Your Internet Service Provider (ISP) has assigned you an IP address that does not change. You will need this address and some additional information (see Step 4) to proceed with installation. PPPoE You have a point-to-point connection to the Internet (used mainly with asymmetric DSL). PPTP Your provider uses point-to-point tunneling protocol (used in Europe). LT2P Your provider uses layer 2 tunneling protocol (used in Europe). After selecting your connection type, click Next. If you chose: Dynamic (DHCP) Proceed to Step 5. Static IP Connection Provide your Static IP Address, Subnet Mask, Gateway IP, DNS, and secondary DNS (optional). This information comes from your ISP. Click Next after entering the information. PPPoE Provide your account name (for example, and password. Click Next after entering the information. PPTP (Europe) Provide your account name (for example, password, and server IP address. Click Next after entering the information. L2TP (Europe) Provide your account name (for example, password, and server IP address. Click Next after entering the information. The Setup Wizard configures your connection, verifies the router settings, and checks the network connection. Click Next. To configure your home network, click Next. Cisco Small Business RV 120W Quick Start Guide 9
10 Configuring Security STEP 1 STEP 2 STEP 3 Enter a new Cisco RV 120W administration password and click Next. For security reasons, you should not use the default password. Follow these password guidelines: Passwords should not contain dictionary words from any language or the default password. Passwords should contain a mix of letters (both upper- and lowercase), numbers, and symbols. Passwords must be at least 8 but no more than 30 characters. Password security ratings are shown to the right of the password you enter, and are rated from weak to secure. Cisco recommends using a password rated as secure. Enter a name (SSID) for your wireless network and click Next. You should change the default SSID to a unique name. The SSID is case-sensitive. NOTE For added security, disable broadcasting of the SSID. You can disable SSID broadcast using the configuration utility; see Using the Configuration Utility, page 12. Select the type of security to use: Best Security (WPA2) Strong wireless security that uses a password (security key) to protect your network. Recommended for most networks. The devices you connect to your wireless network must support WPA2; see the support information for your device if you have questions. a. Enter a security key (must be at least 8 and no more than 63 characters) or use the randomly-generated one provided by the Cisco RV 120W. Keys should contain a mix of letters (both upper- and lowercase), numbers, and symbols. Security key ratings are shown to the right of the key and are rated from weak to secure. Cisco recommends using a key rated as secure. b. Click Next. 10 Cisco Small Business RV 120W Quick Start Guide
11 Better Security (WPA) No Security STEP 4 STEP 5 STEP 6 Wireless security that uses a password (security key) to protect your network. It is less secure than WPA2, but it is supported by older devices. If the devices you are connecting to your wireless network do not support WPA2, choose this option. a. Enter a security key (must be at least 8 and no more than 63 characters) or use the randomly-generated one provided by the Cisco RV 120W. Keys should contain a mix of letters (both upper- and lowercase), numbers, and symbols. Security key ratings are shown to the right of the key and are rated from weak to secure. Cisco recommends using a key rated as secure. b. Click Next. This option is not recommended; it allows devices to connect to your wireless network if the network name is known. a. Click Next. b. Click Yes when the warning message is displayed. The security settings for your network are shown. To save these settings in a text file on your PC, check the box provided. To print, click Print these settings. Click Next to confirm these settings. (If you chose to save these settings to your desktop, then click OK.) NOTE You must enter this security information on each device that connects to your network. Save this information! The Cisco RV 120W configures your router and displays a status message if the configuration is successful. Click Next. The Cisco RV 120W displays a message if it has been configured and is successfully connected to the Internet. Click Finish. Manually Connecting Your System Use these procedures if you do not want to use the Setup Wizard. NOTE You must connect one PC with an Ethernet cable for the purpose of the initial configuration. After you complete the initial configuration, administrative tasks can be performed using a wireless connection. STEP 1 STEP 2 Connect your equipment as described in Connecting Your Hardware section on page 6. Connect to the configuration utility to view and configure your Cisco RV 120W settings. When you connect to the configuration Cisco Small Business RV 120W Quick Start Guide 11
12 utility, the Getting Started page shows links that you can click to perform basic tasks. At a minimum, we recommend that you: Change the Cisco RV 120W password Review wireless profile and set security settings See Using the Configuration Utility, page 12 for more information. 4 Connecting to Your Wireless Network To connect a device (such as a PC) to your wireless network, you must configure the wireless connection with the security information you entered when you used the Setup Wizard or that you configured using the configuration utility. The following steps are provided as an example; you may need to configure your device differently. For instructions that are specific to your device, consult the user documentation for your device. STEP 1 STEP 2 STEP 3 STEP 4 Open the wireless connection settings window or program for your device. Your PC may have special software installed to manage wireless connections, or you may find wireless connections under the Control Panel in the Network Connections window. Enter the network name (SSID). Choose the type of encryption and enter the security key that you chose when setting up the Cisco RV 120W. If you did not enable security (not recommended), leave these fields blank. Verify your wireless connection and save your settings. 5 Using the Configuration Utility The configuration utility allows you to configure and manage your Cisco RV 120W, including the following tasks: View system status information Configure local and wide-area network settings Configure wireless security, firewall, and VPN settings 12 Cisco Small Business RV 120W Quick Start Guide
13 Configure quality of service Perform software upgrades This section describes how to connect to the configuration utility and provides an overview of the utility and some common tasks. For more information on using the configuration utility, see the Cisco Small Business RV 120W Wireless-N VPN Firewall Administration Guide (see Where to Go From Here, page 16, for the location of the document). To use the configuration utility: STEP 1 STEP 2 STEP 3 On a PC connected to a LAN port on the back panel of the Cisco RV 120W, start your web browser. (If you have performed the initial configuration using the Setup Wizard, you can connect wirelessly to the Cisco RV 120W.) To connect to the configuration utility, enter in your browser s address field, and press Enter. A password request page appears. In the Username and Password fields, enter the user name and password for your router. The default is admin for both, but if you used the Setup Wizard to configure your router, you should have changed these. Then click Log In. The Getting Started page displays some of the most common configuration tasks. Click these tasks to view the configuration windows. To view other configuration tasks, click a menu item on the left panel to expand it. Click the menu names displayed underneath to perform an action or view a sub-menu. Suggested Next Steps After you log in to the configuration utility, you may want to perform these basic tasks: Configuring WAN (Internet) Settings Choose Networking > WAN and select IPv4 or IPv6 WAN Configuration. Changing the Cisco RV 120W Username and Password Choose Administration > Users and edit the Admin Settings information. Viewing the Wireless Profile and Configuring Security Choose Wireless > AP Profile and configure the wireless network. Cisco Small Business RV 120W Quick Start Guide 13
14 6 Cisco RV 120W Features Front Panel Power The Power LED lights up green to indicate the unit is powered on. Flashes green when the power is coming on or software is being upgraded. WAN LED The WAN (Internet) LED lights up green when the unit is connected to your cable or DSL modem. The LED flashes green when the unit is sending or receiving data over the WAN port. Wireless The Wireless LED lights up green when the wireless module is enabled. The LED is off when the wireless module is disabled. The LED flashes green when the unit is transmitting or receiving data on the wireless module. LAN These four LEDs correspond to the four LAN (Ethernet) ports of the Cisco RV 120W. If the LED is continuously lit green, the Cisco RV 120W is connected to a device through the corresponding port (1, 2, 3, or 4). The LED for a port flashes green when the Cisco RV 120W is actively sending or receiving data over that port. 14 Cisco Small Business RV 120W Quick Start Guide
15 Back Panel RESET Button The Reset button has two functions: If the Cisco RV 120W is having problems connecting to the Internet, press the RESET button for less than five seconds with a paper clip or a pencil tip. This is similar to pressing the reset button on your PC to reboot it. If you are experiencing extreme problems with the Cisco RV 120W and have tried all other troubleshooting measures, press and hold in the RESET button for 10 seconds. This restores the factory defaults and clear all of the Cisco RV 120W settings. LAN Ports (1-4) These ports provide a LAN connection to network devices, such as PCs, print servers, or additional switches. WAN Port The WAN port is connected to your Internet device, such as a cable or DSL modem. ON/OFF POWER SWITCH Press this button to turn the Cisco RV 120W on and off. When the button is pushed in, power is on. Power Port The power port is where you connect the AC power cable. Cisco Small Business RV 120W Quick Start Guide 15
16 7 Where to Go From Here Support Cisco Small Business Support Community Online Technical Support and Documentation (Login Required) Phone Support Contacts Software Downloads (Login Required) Product Documentation Cisco RV 120W Cisco Small Business Cisco Partner Central for Small Business (Partner Login Required) Cisco Small Business Home Marketplace small_business_support_center_contacts.html Go to tools.cisco.com/support/downloads, and enter the model number in the Software Search box. tsd_products_support_series_home.html Cisco Small Business RV 120W Quick Start Guide
17 Cisco Small Business RV 120W Quick Start Guide 17
18 18 Cisco Small Business RV 120W Quick Start Guide
19 Cisco Small Business RV 120W Quick Start Guide 19
20 Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA USA Tel: NETS (6387) Fax: Cisco, Cisco Systems, the Cisco logo, and the Cisco Systems logo are registered trademarks or trademarks of Cisco Systems, Inc. and/or its affiliates in the United States and certain other countries. All other trademarks mentioned in this document or Website are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (0705R) 2009 Cisco Systems, Inc. All rights reserved. Printed in Taiwan
Quick Start Guide Cisco SPA100 Series Analog Telephone Adapters SPA112 Two Port Phone Adapter SPA122 ATA with Router Package Contents Analog Telephone Adapter Ethernet Cable Power Adapter Quick Start Guide
Quick Start Guide Cisco Small Business WAP371 Wireless AC/N Dual Radio Access Point with Single Point Setup Quick Start Guide Versión en Español para México en el CD Version en français sur CD Versione
Initial Access and Basic IPv4 Internet Configuration This quick start guide provides initial and basic Internet (WAN) configuration information for the ProSafe Wireless-N 8-Port Gigabit VPN Firewall FVS318N
Quick Start Guide Cisco Small Business Pro SR 520-T1 Secure Router Package Contents SR 520-T1 Secure Router Ethernet Network Cable Console Cable AC Power Cord and AD/DC Power Adapter Power Cord Locking
Hardware Installation: 1. Turn off your modem. 2. Use one Ethernet cable to connect your modem to WAN port (Blue) port of BR-6228nC. 3. Use another Ethernet cable to connect your PC to one LAN Port (Yellow)
Chapter 1 Configuring Internet Connectivity This chapter describes the settings for your Internet connection and your wireless local area network (LAN) connection. When you perform the initial configuration
ADMINISTRATION GUIDE Cisco Small Business RV180 VPN Router RV180W Wireless-N Multifunction Router June 2012 Cisco and the Cisco Logo are trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S.
Chapter 1 Configuring Basic Connectivity This chapter describes the settings for your Internet connection and your wireless local area network (LAN) connection. When you perform the initial configuration
DAP-1360 Wireless N 300 Access Point & Router BEFORE YOU BEGIN Delivery Package Access point DAP-1360 Power adapter DC 12V Ethernet cable (CAT 5E) (brochure). If any of the items are missing, please contact
Quick Start Guide Cisco Small Business 200E Series Advanced Smart Switches Welcome Thank you for choosing the Cisco 200E series Advanced Smart Switch, a Cisco Small Business network communications device.
ADMINISTRATION GUIDE Cisco Small Business RV220W Wireless-N Network Security Firewall Cisco and the Cisco Logo are trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S. and other countries.
ASUS WL-5XX Series Wireless Router Internet Configuration User s Guide Contents Chapter 1 Introduction:...1 Chapter 2 Connecting the wireless router...1 Chapter 3 Getting to know your Internet connection
Connect the supplied power-adapter to the power inlet port and connect it to a wall outlet. Then, the router automatically enters the self-test phase. During self-test phase, RNX-EasyN400 s Power LED will
USER GUIDE AC2400 DUAL BAND GIGABIT Wi Fi ROUTER Model# E8350 Table of Contents Product overview E8350..................................... 1 Setting Up Your E-Series Router Where to find more help.........................
Table of Contents General Information...1 Verify Computer Settings...1 Router Installation...3 Configuring Your Router...3 Configuring Your Computer...7 Configuring Your Email...9 General Information Router
N150 Wireless Router Setup Manual NETGEAR, Inc. 350 E. Plumeria Drive San Jose, CA 95134 USA July 2010 208-10679-01 v1.0 2010 by NETGEAR, Inc. All rights reserved. Trademarks NETGEAR and the NETGEAR logo
Wireless G Broadband Router quick install guide Model 503693 INT-503693-QIG-0608-02 Thank you for purchasing the INTELLINET NETWORK SOLUTIONS Wireless G Broadband Router, Model 503693. This quick install
This article describes how to manually configure a Linksys Router for broadband DSL that uses PPPoE (Point-to-Point Protocol over Ethernet) for authentication. For automatic configuration options, please
This product can be set up using any current web browser, i.e., Internet Explorer 6 or Netscape Navigator 6.2.3. DVG-2101SP VoIP Telephone Adapter Before You Begin 1. If you purchased this VoIP Telephone
Quick Start Guide Cisco Small Business 200 Series 8-Port Smart Switches Welcome Thank you for choosing the Cisco 200 Series 8-Port Smart Switch, a Cisco Small Business network communications device. This
Start Here Follow these instructions to set up your router. Verify That Basic Requirements Are Met Assure that the following requirements are met: You have your broadband Internet service settings handy.
Wireless Router Setup Manual NETGEAR, Inc. 4500 Great America Parkway Santa Clara, CA 95054 USA 208-10082-02 2006-04 2006 by NETGEAR, Inc. All rights reserved. Trademarks NETGEAR is a trademark of Netgear,
DIR-620 Multifunction Wireless Router Supporting GSM, CDMA, WiMAX with Built-in 4-port Switch BEFORE YOU BEGIN Delivery Package Multifunction wireless router DIR-620 Power adapter DC 5V/2.5A Ethernet cable
Home Wi-Fi Gateway Instructions 1. Connect the gateway. Use the coaxial cable provided by BendBroadband to connect the cable port (A) to your cable outlet. 2. Connect your computer to the cable modem gateway
Using Cisco UC320W with Windows Small Business Server This application note explains how to deploy the Cisco UC320W in a Windows Small Business Server environment. Contents This document includes the following
This product can be set up using any current web browser, i.e., Internet Explorer 6 or Netscape Navigator 6.2.3. DVA-G3340S Wireless VoIP Router Before You Begin If you purchased this Router to share your
Package Contents 2300 Series Camera Stand Kit Power Supply (12V 1A) 6 Ethernet Cable Lens Adapter Ring Allen Wrench Quick Installation Guide Setup CD Antenna (WVC2300) Business Internet Video Camera with
Network Setup Guide 1 Glossary 1.1 Static IP Computers are communicated and recognized by their own unique IP addresses over the Internet. Static IP provided by your ISP (Internet Service Provider) means
Note The product model shown in this part is TL-R460, as an example. Turn off all of your network devices, including your computer, Modem and the Router. Connect the WAN port on your Router to the Modem
A Division of Cisco Systems, Inc. Broadband Router with 2 Phone Ports Voice Installation and Troubleshooting Guide Model No. RTP300 Copyright and Trademarks Specifications are subject to change without
User Guide Linksys X1000 N300 Wireless Router with ADSL2+ Modem Contents Contents Product Overview X1000..................................... 1 Top 1 Back 1 Wall-mounting placement 2 Installation Set up
ADMINISTRATION GUIDE Cisco Small Business RV120W Wireless-N VPN Firewall Revised June 2011 Cisco and the Cisco Logo are trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S. and other countries.
Chapter 3 Connecting the FWG114P v2 to the Internet This chapter describes how to set up the router on your local area network (LAN) and connect to the Internet. You will find out how to configure your
ADMINISTRATION GUIDE Cisco Small Business RV0xx Series Routers RV042 Dual WAN VPN Router RV042G Gigabit Dual WAN VPN Router RV082 Dual WAN VPN Router RV016 Multi-WAN VPN Router Cisco and the Cisco logo
Broadband ADSL2+ Modem DM111PSPv2 User Manual 350 East Plumeria Drive San Jose, CA 95134 USA August 2011 202-10913-01 v1.0 2011 NETGEAR, Inc. All rights reserved No part of this publication may be reproduced,
Chapter 6 Using Network Monitoring Tools This chapter describes how to use the maintenance features of your RangeMax Wireless-N Gigabit Router WNR3500. You can access these features by selecting the items
Connecting to the Internet LAN Hardware Requirements Computer Requirements LAN Configuration Requirements Installation Performed by Time Warner Cable Technician Connecting via Ethernet Connecting via USB
1 Manual Wireless Extender Setup Instructions Before you start, there are two things you will need. 1. Laptop computer 2. Router s security key Setting up LAN Static IP on PC We need to set up a Static
N600 Wireless Dual Band Gigabit Router WNDR3700v3 Setup Manual NETGEAR, Inc. 350 E. Plumeria Drive San Jose, CA 95134 USA May 2011 208-10774-02 v1.0 2011 by NETGEAR, Inc. All rights reserved. Trademarks
To avoid users without access right through your WLAN Broadband Router, suggest that use security mechanism like WEP, WPA or set ID/password for web configuration login IP address 192.168.1.254. Preparation
Almond Quick Setup Guide 2 Contents 1 Introduction 1.1 Getting to know your Almond 2 Connecting your Almond as a Range Extender (Repeater) 3 Connecting your Almond as a Router 3.1 Using your Almond with
STATIC IP SET UP GUIDE VERIZON 7500 WIRELESS ROUTER/MODEM Verizon High Speed Internet for Business Verizon High Speed Internet for Business SETTING UP YOUR NEW STATIC IP CONNECTION AND IP ADDRESS(ES) This
USER GUIDE Cisco Small Business WBPN Wireless-N Bridge for Phone Adapters December 2011 Cisco and the Cisco Logo are trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S. and other countries.
Note Please use only wired network connections to configure the Router. Turn off all of your network devices, including your computer, Modem and the Router. Connect the WAN port on your Router to the Modem
OvisLink OV804WVA Quick Installation Guide 1 Indicators and Interfaces 1.1 Front Panel LED Color Status Description Power Red DSL Internet Red WAN LAN4-1 Off Power off. The initialization is normal. Initiating.
User Manual July 2015 202-11412-02 350 East Plumeria Drive San Jose, CA 95134 USA Support Thank you for selecting NETGEAR products. After installing your device, locate the serial number on the label of
Contents Section A Networking Basics...................................... 1 1 Learning the Basics............................................. 3 Selecting a network connection........................................
This product can be set up using a current web browser. DIR-100 Triple Play Router Before You Begin Make sure you have all the necessary information and equipment on hand before beginning the installation.
DSL-2750U 3G/ADSL/Ethernet Router with Wi-Fi and Built-in Switch BEFORE YOU BEGIN Delivery Package Router DSL-2750U Power adapter DC 12V/1A RJ-11 telephone cable Ethernet cable (CAT 5E) Splitter (brochure).
Model: FI8910W Quick Installation Guide (For Windows OS) (For MAC OS please go to page 17) Indoor MJPEG Pan/Tilt Wireless IP Camera Black White Package Contents IP Camera FI8910W with IR-Cut.x 1 DC Power
Chapter 7 Troubleshooting This chapter provides troubleshooting tips and information for your ProSafe VPN Firewall 200. After each problem description, instructions are provided to help you diagnose and
User Guide Contents Contents Overview Package contents 1 Back view 1 Bottom view 2 How to expand your home network 3 What is a network? 3 How to expand your home network 3 Where to find more help 3 Operating
User Manual February 2015 202-11472-04 350 East Plumeria Drive San Jose, CA 95134 USA Support Thank you for selecting NETGEAR products. After installing your device, locate the serial number on the label
This product can be set up using any current web browser, i.e., Internet Explorer 6 or Netscape Navigator 6.2.3. DSL-G604T Wireless ADSL Router Before You Begin 1. If you purchased this Router to share
your Gateway Windows network installationguide 802.11b wireless series Router model WBR-100 Installing Configuring Contents 1 Introduction...................................................... 1 Features...........................................................
StarMOBILE Network Configuration Guide A guide to configuring your StarMOBILE system for networking INTRODUCTION... 3 BEFORE YOU BEGIN... 3 1) CONFIRM YOU HAVE THE LATEST SOFTWARE... 3 2) INSTALL THE STARMOBILE
Quick Setup Guide for 3G/ 4G LTE Super Modem III 1. 3G/ 4G LTE Super Modem III Packing List : Before you start installing the router, please verify that the package contains the following items: One Set
System Requirements Computers with Windows, Macintosh, or Linux-based operating systems and an installed Ethernet Adapter Internet Explorer version 7.0 or Firefox 3.0 or higher (for configuration) Package
NETGEAR, Inc. 4500 Great America Parkway Santa Clara, CA 95054 USA 208-10123-01 April 2007 2007 by NETGEAR, Inc. All rights reserved. Trademarks NETGEAR is a trademark of Netgear, Inc. Microsoft, Windows,
Configuration Manual English version Frama F-Link Configuration Manual (EN) All rights reserved. Frama Group. The right to make changes in this Installation Guide is reserved. Frama Ltd also reserves the
STATIC IP SET UP GUIDE VERIZON D-LINK 2750B & ACTIONTEC GT784 WNV WIRELESS GATEWAY Verizon High Speed Internet for Business Verizon High Speed Internet for Business YOUR NEW STATIC IP CONNECTION AND SET
Chapter 6 Using Network Monitoring Tools This chapter describes how to use the maintenance features of your RangeMax Dual Band Wireless-N Router WNDR3300. You can access these features by selecting the
The HP M220 is a Wi-Fi Alliance authorized Wi-Fi CERTIFIED 802.11a/b/g and 802.11n product. The Wi-Fi CERTIFIED logo is a certification mark of the Wi-Fi Alliance. HP M220 802.11n Access Point Quickstart
Quick Installation Guide (For Windows & Mac OS) Outdoor Wireless IP Camera Package Contents V1.1 IP Camera Power Adapter Resource CD Ethernet Cable Mounting Bracket(except FI8919) Wi-Fi Antenna Quick Installation
LW310V2 Sweex Wireless 300N Router Please notice! On the included CD-ROM you will find the Setup Wizard. This easy install procedure will show you how to setup the router step-by-step. Do not expose the
AC1900, N900, and N450 WiFi Cable Data Gateways Models C6300BD, CG4500BD, and CG3000Dv2 User Manual March 2015 202-11434-03 350 East Plumeria Drive San Jose, CA 95134 USA Support Thank you for selecting
10/2011 - English Edition 1 Quick Start Guide NWA1100N-CE CloudEnabled Business N Wireless Access Point Package Contents - 1 x ZyXEL NWA1100N-CE Access Point - 2 x Detachable Antennas - 1 x Power Adapter
Wireless-G Broadband Gateway GWA501 Quick Start Guide Read this guide thoroughly and follow the installation and operation procedures carefully to prevent any damage to the unit and/or any of the devices
USER GUIDE BUSINESS SERIES 10/100 4-Port VPN Router Model: RV042 About This Guide About This Guide Icon Descriptions While reading through the User Guide you may see various icons that call attention to
Wireless-G Broadband Router GWA502 Quick Start Guide Read this guide thoroughly and follow the installation and operation procedures carefully to prevent any damage to the unit and/or any of the devices
For the Way You Live & Work Quick & Easy Set-Up of Packet8 Internet Phone Service Welcome to Packet8 Internet Phone Service. Soon, you ll be able to make all your calls over the Internet and save a bundle