Welcome to Hartac s latest Signs & Safety Solutions Catalogue

Transcription

1 Marine Offshore Welcome to Hartac s latest Signs & Safety Solutions Catalogue This catalogue has been designed to assist our customers in selecting the correct signs and equipment to meet the regulatory standards and codes pertaining to their industry. It has always been our policy to manufacture signs that will give maximum life, using materials designed to withstand hostile conditions, and to supply safety products of the highest standard. We offer a complete service from laser engraving to custom designed mine site name and information signs. Surveys can be arranged with our trained representatives, to advise you on the correct signs to be installed. SIGNS & SAFETY SOLUTIONS 50

2 MARINE AND OFFSHORE SIGNS These products comply with systems and equipment for marine and offshore safety. All photoluminescent products comply with the requirement of IMO. All photoluminescent products are manufactured to the highest quality standards. PHOTOLUMINESCENT SIGN & TAPE MATERIAL SPECIFICATIONS: Self Adhesive Vinyl: Flexible laminated PVC composite material incorporating a photoluminescent layer thermally welded to a white reflective layer. Backed with pre-applied adhesive. Thickness: 0.6mm. Indoor durability: in excess of 5 years. Outdoor durability: good, but can reduce in strong sunlight and humidity. Toxicity: non-toxic, non-radioactive and contains no phosphorous or lead. Chemical resistance: resistant to most common cleansing agents. Flammability: inherently fire retardant. Adhesive: cross linked acrylic, pressure sensitive permanent adhesive with silicone release backing paper. Luminance performance: in excess of 10 mins and 60 mins when tested in accordance with Din part 1. Rigid PVC: Laminated PVC sheet incorporating a photoluminescent layer backed by a rigid white reflective substrate and protected by a tough, clear gloss PVC film. All laminations are thermally welded to form a cohesive sheet. Thickness: 1.4mm. Indoor durability: in excess of 5 years. Outdoor durability: excellent, but can reduce in strong sunlight. Toxicity: non-toxic, non-radioactive and contains no phosphorous or lead. Chemical resistance: resistant to most common cleansing agents. Flammability: inherently fire retardant. Luminance performance: in excess of 10 mins and 60 mins when tested in accordance with Din part 1. NON-PHOTOLUMINESCENT SIGN & POSTER MATERIAL SPECIFICATIONS: Self Adhesive Vinyl: Flexible gloss white vinyl material. Weight: 110g/m2. Thickness: 80 micron. Dimensional stability: 0.5mm max to DIN Outdoor durability: approximately 2 years. Chemical resistance: no effect from oils, greases, aliphatic solvents, heptane and kerosene. Flammability: self extinguishing. Adhesive: emulsion based, UV resistant, permanent adhesive with high initial tack and adhesion. Gloss: 60 to ISO 2831, 20o, MD. Opacity: 90% 51 SIGNS & SAFETY SOLUTIONS

3 SAFETY SIGNS Safety Signs are required to complement or expand the scope of officially designated signage. Many of the above signs will be required by various Registration and Classification Authorities to cover safety and life saving equipment. With increasing numbers of new vessel and safety equipment designs appearing, special signage is always required. We are happy to manufacture signage to customer s designs in the event of our standard range not meeting specific requirements. Sign 4130 LJ is an example of this. Based on the IMO symbol, this sign neatly overcomes the problems associated with stowage of lifejackets in high speed ferry cabins. Installation: All first aid points and first aid storage should be marked, as should emergency telephones and emergency stop buttons. Chemical carriers and vessels carrying hazardous cargoes should mark emergency showers and eye washes with the appropriate signs. JJ=150mmx150mm Self Adhesive. EE-50mmx50mm Self Adhesive. GM=300mmx300m SIGNS & SAFETY SOLUTIONS 52

4 DIRECTIONAL SIGNS GM=100mmx300m 53 SIGNS & SAFETY SOLUTIONS

5 DIRECTIONAL SIGNS CONTINUED Regulations: SOLAS Chapter II-2 Regulation , requires all escape route signs to be photoluminescent material, or marked by light, or both. IMO publication IMO-981E indicates that exit signs should comprise of a running man pictogram, an arrow, and the word EXIT. Installation: Primary escape routes should be marked with signs comprising the running man pictogram, a directional arrow, and the word EXIT. Secondary escape routes should employ similar signs but with the wording EXIT for emergency use only. Signs should be positioned approximately 1700mm from deck level for normal direction marking, and not more than 300mm from deck level for LLL systems. Where possible, signs at doors or hatches should be positioned above the door so that the sign is still visible when the door is open. Directional signs over doors should be limited to either a sign containing a vertical arrow, indicating the escape route continues through the door, or to the running man pictogram plus the word EXIT indicating that the door is the final exit. Where the door hinges on the right a sign with the man running to the left should be used, conversely with a door hinged on the left the running man should face to the right. Frequency of marking is almost impossible to define accurately, as the final decision rests with the surveyor accepting the route marking, however, the following points should be adhered to: 1) Every change of direction should be marked with the appropriate sign 2) Signs in an alley or corridor should be spaced at intervals no greater than the maximum viewing distance of the sign employed (see first page for details of maximum viewing distances). 3) When in public or communal areas an EXIT sign should be within a 360o field of view. Where more appropriate (e.g. crew accommodation and machinery spaces), escape routes may be marked with the muster/assembly or embarkation station directional signs shown. JP=400mmx150mm. JM=300x150mm. JJ150x150mm. GG=66mmx100mm SIGNS & SAFETY SOLUTIONS 54

6 IMO FIRE CONTROL SIGNS JJ=150mmx150mm 55 SIGNS & SAFETY SOLUTIONS

7 IMO FIRE CONTROL SIGNS CONTINUED Regulations: Resolution A654(16) amending Chapter II-2, Regulation 20 requires the use of these symbols on fire control plans and booklets as an international standard. These symbols are often used to identify actual equipment where no standard sign is available. JJ=150mmx150mm SIGNS & SAFETY SOLUTIONS 56

8 FIRE EQUIPMENT SIGNS JJ=150mmx150mm. GM=300x100mm GG=100x100mm 57 SIGNS & SAFETY SOLUTIONS

9 FIRE EQUIPMENT SIGNS CONTINUED Regulations: SOLAS Chapter II-2, Regulation , requires all fire equipment location markings to be photoluminescent material or marked by lighting. Installation: Each item of fire fighting equipment should be marked with the appropriate symbol. Where various types of equipment are stored at one location, Fire Point signs may be used. When equipment in an alley or corridor is stowed in a recess or locker, then a panoramic sign, mounted well above head height, should be used to enable the equipment to be identified from a distance (see first page for details on viewing distances). Any space protected by a CO2 blanketing system must have all entrance doors and hatches marked by the appropriate sign. See signs 5876 KJ and 7545 KJ in the above diagrams. All elevator entrances should be marked with sign 6300 JJ. Fire extinguishers may be further identified as to their use with signs 6410 KG to 6413 KG which comply with European Regulation EN 3. JJ=150mmx150mm. KJ 150mmx200mm. KG=100x200mm SEA LANTERNS SEA LANTERNS PN: SL60-R PN: SL60-G PN: SL60-A PN: SL60-B PN: SL60-W 2 nautical mile range (3.6km) Red, Green, Amber, Blue and White available 256 IALA flash patterns, user adjustable without the need for external devices User-replaceable battery in sealed battery compartment 4 user-adjustable intensity settings ON/OFF storage switch Includes Bird Spike Installs in minutes and operates maintenance-free for up to five years Affordable and tough Three Year Warranty SIGNS & SAFETY SOLUTIONS 58