BEADS OF COURAGE BOXES USING BIRD S MOUTH ROUTER BITS FOR STAVE CONSTRUCTION Part A
|
|
- Lucas Norman
- 7 years ago
- Views:
Transcription
1 BEADS OF COURAGE BOXES USING BIRD S MOUTH ROUTER BITS FOR STAVE CONSTRUCTION Part A REFERENCE: LEE VALLEY TOOLS-BIRD S-MOUTH JOINERY BITS MATERIALS NEEDED: 1. ROUTER TABLE WITH ROUTER 2. BIRD S MOUTH BITS FOR 6, 8, 16, or 12 STAVES 3. ONE-INCH OR 4/4 LUMBER OF CHOICE (Not less than.75 finished) 4. LUMBER FOR BASE AND TOP OF BOX (3/4 to 7/8 ) 5. THREE HOSE CLAMPS OF SUITABLE DIAMETER PER BOX (5.5 to 7.5 ) 6. LATHE FOR TURNING BOX 7. LATHE TOOLS FOR TURNING 8. TITE BOND III GLUE OR SUITABLE WOOD GLUE 9. TWO FACE PLATES WITH 4 TO 5 DIAMETER GLUE BLOCKS ATTACHED 10. FINISH OF YOUR CHOICE SUCH AS WATCO DANISH OIL OR DEFT SPRAY. NICE TO HAVE ACCESSORIES (OR A FRIEND WITH THE ACCESSORIES): 1. COLE JAWS OR OTHER CHUCK FOR REVERSE CHUCKING THE FINISHED BOX TO DO THE BOTTOM. 2. JOINTER, CHOP SAW, OR TABLE SAW FOR MILLING LUMBER TO BE USED. 3. BEALL BUFFING SYSTEM. 4. AN EXTRA PAIR OF HAND (Invite a buddy over) 1
2 STEPS IN COMPLETING BOX 1. MILL LUMBER ON FOUR SIDES, THICKNESS SHOULD BE.75 TO LENGTHS OF MILLED LUMBER SHOULD VARY FROM 2 TO 4 FOR EASE OF HANDLING. 3. RIP MILLED LUMBER TO PROPER WIDTH: a. 6 SIDES, WIDTH OF BOARD=DIAMETER/1.7 b. 8 SIDES, WIDTH OF BOARD=DIAMETER/2.4 FOR EXAMPLE: EIGHT STAVES FOR A 7.5 DIAMETER BOX, THE BOARD WIDTH= c. 12 SIDES, WIDTH OF BOARD=DIAMETER/3.7 d. 16 SIDES, WIDTH OF BOARD=DIAMETER/ USING BIRD S MOUTH ROUTER BIT, CUT BIRD S MOUTH ALONG ONE OF THE THICKNESS SIDES. USE LUMBER OF LENGTHS 2 TO 4 FOR EASE OF HANDLING. EACH PIECE OF LUMBER SHOULD BE RUN THROUGH THE ROUTER BEFORE ADJUSTING FENCE TO MAKE A SECOND OR SUBSEQUENT PASS. YOU CAN ALSO RUN EACH OF THE STAVES THROUGH INDIVIDUALLY. 5. CUT EACH 2 TO 4 LENGTH INTO SMALLER PIECES EQUAL TO THE CHOSEN HEIGHT OF THE BOX. THESE PIECES CAN BE CUT ON THE TABLE SAW OR CHOP SAW AND SHOULD ALL BE THE SAME LENGTH. CUTTING THE STAVES TO LENGTH CAN BE DONE BEFORE OR AFTER USING THE ROUTER TABLE. 6. DRY CLAMP THE PIECES FOR A BOX TOGETHER TO CHECK THE FIT, IF SATISFACTORY, THEN BEGIN THE GLUING PROCESS. 7. FOR EXAMPLE, USING 8 STAVES, GLUE TWO STAVES TOGETHER AT A TIME, THEN COMBINE INTO FOUR PIECES THEN COMBINE THE TWO FOUR-PIECES TO COMPLETE AN EIGHT SIDED BOX. USE A SIMILAR PROCESS FOR BOXES WITH A DIFFERENT NUMBER OF STAVES. TRY TO GET THE BOTTOM OF THE STAVES IN THE SAME PLANE TO REDUCE ANY TOUCH UP SANDING OF THE BOTTOM OF THE STAVES. BOTTOM CAN BE HAND SANDED OR A DISC SANDER CAN BE USED TO ENSURE THE BOTTOM OF THE STAVE CYLINDER IS FLAT. (Extra pair of hands very helpful) 8. ONCE ALL SIDES ARE GLUED TOGETHER, USING THREE HOSE CLAMPS PER BOX, CLAMP THE PIECES TOGETHER (A buddy is very helpful at this stage) 9. LET THE GLUED STAVE CYLINDER CURE OVERNIGHT. 10. THE TURNING OF THE BOX CAN BE ACCOMPLISHED ONE OF SEVERAL WAYS. YOU MAY BE ABLE TO THINK OF ANOTHER WAY SUITABLE FOR YOU. 2
3 METHOD 1. a. PREPARE CONES LARGE ENOUGH TO FIT IN BOTH THE ENDS OF THE HOLLOW STAVES (One attached to a chuck for the headstock and one for the tail stock. A SMALL SHOULDER CAN BE TURNED ON EACH CONE SO THE CYLINDER FITS FLAT AGAINST THE CONE. b. TURN THE STAVES TO A ROUND CYLINDER AND SAND BUT DO NOT FINISH. PREPARE THE BASE OF THE BOX BY TAPING THE BOTTOM OF THE BASE TO A GLUE BLOCK WITH DOUBE FACED TAPE AND TURN ROUND TO SAME DIAMETER AS THE STAVE CYLINDER (Can be slightly larger). c. GLUE THE STAVE CYLINDER TO THE BASE AFTER ENSURING THE BOTTOM OF THE STAVES ARE IN THE SAME PLANE AND THE BASE IS FLAT. d. CENTERING THE STAVE CYLINDER ON THE BASE IS CRITICAL. USE A PRESS OF YOUR CHOICE TO CLAMP THE BASE AND STAVES TOGETHER. LET GLUE CURE. e. TURN THE BASE & STAVES ROUND AND HOLLOW THE INSIDE OR LEAVE THE INSIDE AS A POLYGON (Hand sand the inside if left as a polygon). SAND TO 400 GRIT. f. PREPARE TOP OF BOX BY TAPING THE BOTTOM OF THE TOP TO A GLUE BLOCK AND TURN ROUND. FIT THE TOP TO THE TOP OF THE STAVES AS YOU DESIRE. REMOVE TOP FROM GLUE BLOCK AND TAPE THE TOP TO THE TOP OF STAVES TO FINISH THE TOP. WHEN TOP IS FINISHED AND SANDED REMOVE IT. g. REMOVE THE BOX (BASE/STAVES) FROM THEIR GLUE BLOCK. REVERSE CHUCK TO FINISH THE BOTTOM OF THE BOX (Cole Jaws work very well for this). h. FINISH AS DESIRED. METHOD 2. ALMOST THE SAME AS METHOD 1, EXCEPT THE STAVE CYLINDER IS GLUED TO THE BASE PRIOR TO TURNING THE STAVE CYLINER ROUND THE BOTTOM OF THE STAVES AND THE BASE BOTH MUST BE SUPERFLAT SO THAT A GOOD GLUE JOINT IS ACHIEVED. IF DONE WELL, AFTER TURNING THE GLUED BASE AND STAVES ROUND ANY DESCREPANCY AS SEEN INSIDE THE CYLINDER RELATIVE TO CENTERING SHOULD BE NEGLIGIBLE. OTHER METHODS: To be determined by the individual woodturner. 3
4 NOTE: For a given cutter and outside diameter, there is a minimum material thickness that can be used and still made round. This thickness can be determined by using one of the formulae below. The formulae allow for a minimum wall thickness equal to 2/3 of the initial minimum material thickness. 6-sided: Thickness=Diameter/6.3 8-sided: Thickness=Diameter/ sided: Thickness=Diameter/ sided: Thickness=Diameter/36 This handout prepared by Jon Searles ( ) and Mark Duval ( ). Any questions may be directed to either person. Let us know if you have another method of construction for the stave box. 4
5 Photographs of stages of assembly of the Beads of Courage Box Figure 1: Prepared blanks for top, base and staves of a 6 diameter, 8 stave, 5 high Beads of Courage Box. 5
6 Figure 2: Base has been flattened on both sides. Base is mounted to a glue block with double-face tape. Figure 3: Base turned round to the selected box diameter. 6
7 Figure 4: Material prepared for assembly (rounded base on glue block, staves routed along one edge using bird s mouth router bit and rounded blank for the top of box). Figure 5: Staves dry fitted and clamped prior to gluing. Two or three clamps can be used. 7
8 Figure 6: Glue up sequence. Glue pairs together, then glue two pairs together to form half a cylinder, then glue two half cylinders to form the stave cylinder. Place two or three clamps on the glued cylinder and tighten ensuring that joints are tight and aligned and bottom of all staves lie in the same plane. Let glued cylinder cure overnight. 8
9 Figure 7: Remove clamps from the cylinder and check bottom of staves. Hand sanding on a piece of 100 grit should remove any slight differences so that the bottom of all staves are in the same plane. Figure 8: Glue cylinder to base. Pay careful attention to getting the cylinder centered on the base. This can be done by feel or by using a tail stock cone after mounting the base and cylinder on the lathe. 9
10 10
Ladder Shelf Plans Final dimensions: 25 L x 21 W x 72 H
Ladder Shelf Plans Final dimensions: 25 L x 21 W x 72 H Copyright 2011. MLCS Woodworking. Page 1 Router bits and supplies needed: 3/8 Rabbeting bit (#10691) 1 Bottom Cleaning bit (#7941) Top and Bottom
More informationPepper Mill Instructions by Fred Kachelhofer
by Fred Kachelhofer I have seen Nick Cook turn a pepper mill twice and read his article posted at http://www.nickcookwoodturner.com/articles.htm (follow link and then click on Pepper Mill ). I have had
More informationSEGMENTED WOODTURNING
Notes on: SEGMENTED WOODTURNING Malcolm Tibbetts www.tahoeturner.com malcolm@tahoeturner.com (530) 541-6135 MATHEMATICAL FORMULAS AND CONCEPTS: A circle contains 360 Circumference = Diameter x π(3.1416)
More informationRaised Panel Doors Made Simple With Freud s 2+2 Raised Panel Bit Set
Raised Panel Doors Made Simple With Freud s 2+2 Raised Panel Bit Set Congratulations on your purchase of Freud s world class 2 + 2 Raised Panel Bit Set. This revolutionary design combines two small wings
More informationThe Basics of Stave Segmented Turning
The Basics of Stave Segmented Turning Notes by Jim Rodgers Version 1.2 February, 2005 JL Rodgers, Incorporated 36 Briar Drive Martinez, CA 94553 9925) 229-5773 The Basics of Stave Segmented Turning Requirements
More informationBuilding an Off-Center Fixture for Turning Pendants
Building an Off-Center Fixture for Turning Pendants Turning a pendant off-center with most available metal pendant chucks means that you will have a significant amount of mass off center, which will limit
More informationGate Leg Drop Leaf Table Plans
Preparing the table top blanks: Cut and glue enough 3/4 stock to make three panels 40 long by 24 wide (they will be cut to final size at a later time). While the glue dries we will work on the legs. Preparing
More informationWoodturning Project Tutorials by Larry Hancock. 2004, 2005 Larry Hancock, turnedtreasures.com. Gavel Turning
Woodturning Project Tutorials by Larry Hancock 2004, 2005 Larry Hancock, turnedtreasures.com Gavel Turning Before you can start to turn a gavel the design, size, and wood need selected. The design I used
More informationMaking Wooden Hinges
Making Wooden Hinges By Alex Reid - www.mokkou.jp Materials and tools used - 3.2mm straight router bit - 1/8 round-over router bit - Flush-cut straight bit (with bearing on bottom) - Finger-joint jig -
More informationHow to Build a Poker Table
How to Build a Poker Table www.pokertablematerials.com 10-Person Poker Table- 96 x 48 These are step by step instructions for building a poker table. The table will measure 48" x 96" and have a 4" wide
More informationTurning Crow Calls -The Latta Method-
Turning Crow Calls -The Latta Method- This tutorial will cover how to make a crow call using the molded reeds sets we sell and how to modify them to make a much better end product for you and your customers
More informationComplete Dovetail Jig Instructions
Complete Dovetail Jig Instructions 18 15 1 12 13 8 (22818) 19 17 16 4 3 6 14 5 9 9 11 10 2 PARTS LIST - COMPLETE DOVETAIL JIG Introduction Your new dovetail jig will cut Full Through Dovetails and three
More informationMaking Laminated Rolling Pins
Making Laminated Rolling Pins Introduction Why go to the trouble to make a rolling pin when you can go down to your local discount store and buy one that works just fine for less than $5? As wood turners,
More informationRouter Table Plans. www.bobsplans.com
www.bobsplans.com Router Table Plans Increase the capabilities of your router with this weekend project. Features a sliding fence with EZ-Mount clamps. These clamps are simple to make and grip tightly
More informationThe Hive Bodies. In the Beekeeper s Work Shop. Building a Bee Hive: The Hive Bodies. by Stephen E. Tilmann
The Hive Bodies In the Beekeeper s Work Shop The hive body is the heart of a managed bee hive colony (Figure 1). It is where the queen lays her eggs, the house bees raise the brood and the workers store
More informationwww.cornholesupplies.com
www.cornholesupplies.com How To Build Regulation Cornhole Boards Home of the Original Cornhole Bags and Boards Supply List: 1-4' X 8' Piece of Plywood (pre sanded) 4-2" X 4" X 8' Studs (2 by 4s make sure
More informationHONING LATHE DUPLICATOR CUTTERS
Lay the flat face of the cutter or bit on the flat top surface of the hone with the rest of the cutter overhanging the edge. Rub the cutter or bit up and down the hone (Figure 24-44). Be sure to hold the
More informationHere is your set of Detailed Plans from Copyright 2004 All Rights Reserved
Here is your set of Detailed Plans from Copyright 2004 All Rights Reserved Materials for the House Here is the list of materials you will need to construct the basic house then to cover it with roofing
More informationFRAMED & MOUNTED TILE MURAL
Page 1 of 5 There is no denying that tile murals have taken the sublimation industry by storm. The unique ability to take a customer s artwork or high resolution photograph, tile it using your software
More informationHow to Build Your Own CornHole Game
How to Build Your Own CornHole Game DIMENSIONS Here is a diagram with the basic measurements for the Cornhole board game. SUPPLIES 1/2 thick sheet of plywood one 4 x4 or two 2 x4 s 8 long 2 4 s (4) 4 1/2
More informationHive Top Ventilation Shims
Hive Top Ventilation Shims When preparing your bee hives for the winter, it is very important to provide for ventilation at the top of the hive. Through out the winter, the bees are expelling a lot of
More informationSHELVES. www.tedswoodworking.com
SHELVES It's rare that bookshelves look as interesting as the objects you display on them. After all, how much can you decorate the edges of your shelves and sides? This unit is unusual because the shelves
More informationInstalling Window and Door Mouldings
Installing Window and Door Mouldings About Window and Door Mouldings The trim around windows and doors greatly influences the look and style of your interior. They also bridge the gaps and cover spaces
More informationChapter 3 Installing Over-the-Post Railing on an L-Shaped Stair
49 Chapter 3 Installing Over-the-Post Railing on an L-Shaped Stair In this chapter: The Over-the-Post Balustrade System Determining the Rail Centerline Using Rail Bolts Making a Pitch Block Laying Out
More informationThreaded-lid. Acorn. project that won t fall far from the lathe
Threaded-lid Acorn A The fun Woodturner s project that won t fall far from the lathe By Nick Cook Above: Rich texturing to a 53 4" x 31 2" acorn box enhances the appeal of the Willard Baxter acorn shown
More informationIntroduction to Door Construction
Entry Door Construction Made Simple with Freud s Entry & Interior Door Router Bit System Congratulations on your purchase of Freud s Entry & Interior Door Router Bit System. This unique set allows you
More informationGo-kart for little race-drivers
Go-kart for little race-drivers Drill and drive. Go-kart What it lacks in speed, it more than makes up for in fun: the go-kart will excite little race-drivers. 1 Introduction It s only a go-kart, but it
More informationDIY CABINET REFACING INSTALLATION GUIDE
DIY CABINET REFACING INSTALLATION GUIDE CABINET REFACING INSTALLATION Are you ready to reface your outdated cabinets? This guide will show you how to install your new Facelifters Cabinet Refacing Products
More informationLathe Milling Attachment
Lathe Milling Attachment By L C. MASON BY CLEVERLY stacking cold-rolled flat stock together, T-slots and slide for this lathe milling attachment are made without costly machinery. In fact, only two tools,
More informationMass Customization Strategy for Cabinets, Furniture and Millwork Using Edge Glued Panels
Mass Customization Strategy for Cabinets, Furniture and Millwork Using Edge Glued Panels Wood Education and Resource Center Princeton, West Virginia Thursday, June 3rd, 2010 Sponsored by: US Forest Service
More informationVacuum chucking. MDAE Woodturning Center Course Number 95537001
Purpose of vacuum chucking Vacuum chucking MDAE Woodturning Center Course Number 95537001 Completing the foot of a vessel Re chucking a completed object Quick securing for additional steps (sanding) How
More informationKITCHENS. Tip PAGE 1 FITTING YOUR KITCHEN GUIDE. How to mark out a kitchen. Tools required for installing a kitchen STEP ONE STEP TWO STEP THREE
FITTING YOUR KITCHEN GUIDE How to mark out a kitchen PAGE 1 Before starting on the installation, measure 870mm from the lowest point of the floor and mark a datum line around the room to indicate where
More informationCOMPLIMENTARY WOODWORKING PLAN
COMPLIMENTARY WOODWORKING PLAN Adirondack Chair This downloadable plan is copyrighted. Please do not share or redistribute this plan in any way. It has been created for Wilton Tools, a division of WMH
More informationMaking Clock Wheel & Pinion Cutters
Making Clock Wheel & Pinion Cutters When making hand made clocks or in repair work an odd size cutter is sometimes needed. Sometimes just one pinion is required and does not justify the cost of a commercial
More informationWHI 90-Minute Rated Veneered Door Frame Installation Instructions
No. 940-03-10 INSTALLATION INSTRUCTIONS 90 MINUTE RATED VENEERED DOOR FRAME DOOR REQUIREMENTS: Consult the door manufacturer to make sure that the doors are qualified for the hardware to be installed,
More informationThings you need to assemble the tube actuator. Left to right. are small piece of masking tape, super glue,pen knife and small
Things you need to assemble the tube actuator. Left to right are small piece of masking tape, super glue,pen knife and small crosspoint screwdriver. You will also need a few drops of light oil. Begin by
More informationWooden hinges for boxes using the Leigh F3 template on the D4R Pro jig.
Wooden hinges for boxes using the Leigh F3 template on the D4R Pro jig. Al Navas, Sandal Woods-Fine Woodworking Country Club, Missouri, USA Part 1 a simple prototype Direct link to the original article:
More informationThe "DAVID" Steam Engine By Alan Marconett Hobbit Engineering HTTP://WWW.HobbitEngineering.com Alan@HobbitEngineering.
The "DAVID" Steam Engine By Alan Marconett Hobbit Engineering HTTP://WWW.HobbitEngineering.com Alan@HobbitEngineering.com (c) 2/20/03 The David steam engine is a simple oscillating steam engine, many plans
More informationBuild and Fly the Fokker D- 8
Details are carefully carried out. Note movable controls The high wing gives it unusual stability Build and Fly the Fokker D- 8 Complete Data From Which You Can Build a Successful Model of a Famous German
More informationThe JIG is UP Or A couple hours up front pays in the long run.
Ed Simon Page 1 of 5 The JIG is UP Or A couple hours up front pays in the long run. A large part of the fun of beekeeping is the construction and assembly of the equipment. Since it is a hobby, I decided
More informationBalance Beam Plans. Copyright 2007 Ben MacLeod Email: sales@betterplans.net Website: www.betterplans.net
Balance Beam Plans Copyright 2007 Ben MacLeod Email: sales@betterplans.net Website: www.betterplans.net Balance Beam Plans By Ben MacLeod Copyright 2007 Tools required: -Mitre saw, circular saw, jig saw,
More informationAssembly Instructions Basic Folding-Leg Box Frame Style
Assembly Instructions Basic Folding-Leg Box Frame Style Basic Folding Leg Cornhole Board Concept 1 2 12 3 1 2 3 15 16 4 1 4 52 9 R1 3 4 6 21 48 12 1 4 Bolt Washer 9 13 16 35 Washer Double Nut CornholePlayers.net
More informationINSTALLATION INSTRUCTIONS for Bifold Doors (JII103)
Thank you for selecting JELD-WEN products. Attached are JELD-WEN s recommended installation instructions for premium composite, hollow and solid core molded Bifold Doors. Bifolds are designed for fast
More informationStair Parts Installation. Tricks
Stair Parts Installation Tips & Tricks Introduction Your DIY staircase guide Welcome to the Stairpart home installation guide. Your stairway is both a functional and focal point in your home, so keeping
More informationA Simple Approach to Raised-Panel
A Simple Approach to Raised-Panel 82 FINE HOMEBUILDING Wainscot BY GARY STRIEGLER Stock molding and MDF panels transform a room 1 2 3 4 3 5 6 Raised-panel wainscot speaks of a time when craftsmen had an
More informationFilling Grain and Finishing Calls With CA Glue
Filling Grain and Finishing Calls With CA Glue Call makers use dozens if not hundreds of different products and techniques to finish their calls. The emphasis is on sealing the wood, and giving the call
More informationPicnic Table Plans. Made out of a single sheet of plywood, it s also portable! By Kevin Ayer. This children's picnic table would
Picnic Table Plans Made out of a single sheet of plywood, it s also portable! By Kevin Ayer Materials One 4- by 8-foot sheet of 3 4-inch AC plywood Twelve 11 4-inch wood screws Primer and exterior paint
More informationDINING OUT. Build this outdoor table and bench set. TEXT AND PHOTOS BY NEAL BARRETT Photo by Eugene Thompson
DINING OUT Build this outdoor table and bench set. TEXT AND PHOTOS BY NEAL BARRETT Photo by Eugene Thompson http://popularmechanics.com/home_improvement/furniture/2001/4/table_and_bench_set/print.phtml
More informationTaking Wainscot Up Stairs
Taking Wainscot Up Stairs raised MDF panels and stock moldings bring this elegant trim detail to the rest of the house BY GARY STRIEGLER I credit a lot of the success of my business to the trimwork we
More informationButt Fusion Welding of HDPE Pipes Work Procedure
Butt Fusion Welding of HDPE Pipes Work Procedure A pipeline is as good as its weakest point. Accordingly it is not only important that quality pipes and components are used in a piping system, but also
More informationQWALL 4 ACRYLIC SHOWER WALL INSTALLATION INSTRUCTIONS
QWALL 4 ACRYLIC SHOWER WALL INSTALLATION INSTRUCTIONS IMPORTANT DreamLine TM reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical
More informationCedar Cottage Doghouse Plans
Overlapping cedar shingles add an element of charm to this medium size doghouse. The walls, floor, and trim are constructed of solid cedar, making it naturally weather resistant and provides excellent
More informationMagnetic Levitation Track Construction Instruction Manual August 2012
This document is intended to be used by Science Olympiad teams to assist them in building a magnetically-levitated track that will meet all specifications in the event rules for Magnetic Levitation and
More informationBuilding Pluto Subwoofers with Large PVC Pipe
Building Pluto Subwoofers with Large PVC Pipe I decided to make the Pluto subwoofers from 10-12 diameter PVC pipe. It seemed to me that these would be a better visual match to the Plutos themselves. The
More informationWren Kitchens Installation Tips... 3. Carefully check your kitchen delivery... 4. Measuring out and marking up... 5. Fitting the base cabinets...
tra 1 Index Wren Kitchens Installation Tips... 3 Carefully check your kitchen delivery... 4 Measuring out and marking up... 5 Fitting the base cabinets... 6 Fitting the corner cabinets... 7 The 972mm or
More informationRETROFITTING THE X3 MILLING MACHINE (2)
RETROFITTING THE X3 MILLING MACHINE (2) Dick Stephen continues with the mechanical modifications. Fitting the ball screws The 12mm 2mm pitch supplied by THK ball screws are delivered with the nut fitted
More informationChildren s Furniture Projects
This is an excerpt from the book Children s Furniture Projects by Jeff Miller Copyright 2002 by The Taunton Press www.taunton.com CHILD S ROCKER KIDS ARE ALWAYS IN MOTION. It s not easy to get them even
More informationHow to become an Operation Christmas Child Shoe Box Character
How to become an Operation Christmas Child Shoe Box Character SUPPLIES A large rectangular box (to look like a shoe box) Cardboard or foam strips, 2 wide, for the lid Large printed Boy or Girl shoe box
More informationBUILD A TABLETOP LOOM
BUILD A TABLETOP LOOM From 1" x 2" stock (actual 3/4" x 1"1/2) cut: 4 pieces 15" long 4 pieces 5"1/2 long Use the above to make 2 frames for the front and back of the loom. From 1" x 4" stock (actual 3/4"
More informationSAFETY MANUAL. School of Architecture Building Construction Lab Florida A& M University Tallahassee, Fl (850) 599-3032. Faculty: Deborah LaGrasse
SAFETY MANUAL School of Architecture Building Construction Lab Florida A& M University Tallahassee, Fl (850) 599-3032 Faculty: Deborah LaGrasse TABLE OF CONTENTS WHAT IS SAFETY?... 2 SHOP GOALS SHOP MOTTO
More informationPole Lathe and Shave Horse Design
Pole Lathe and Shave Horse Design These pictures and accompanying words are Copyright Michael Hughes February 2002. They are not to be re-produced, in part or whole, without permission from the author.
More informationTools Required. Recommended Adhesives Vinyl Bonding: - Christy s White Hot Vinyl Cement
Assembly Instructions STEP-BY-STEP HANDRAIL INSTALLATION for 1-1/2" vinyl handrail component system Rise in inches Run in inches 8 8.5 9 9.5 10 10.5 11 11.5 12 12.5 13 13.5 14 14.5 15 8.5 47 45 43 42 40
More informationOvernight Sensations Speaker Kit
Overnight Sensations Speaker Kit Thank you for purchasing the Overnight Sensation cabinet kit. This speaker kit was precision cut using CNC machinery for the best possible fit and finish. With a little
More informationSkirt 1 / 4. The Skirt. The skirt patterns were downloaded from Mark's site but they need expanding before they can be used.
Skirt 1 / 4 The Patterns The Skirt The skirt patterns were downloaded from Mark's site but they need expanding before they can be used. I used Corel Draw's real world dimensions to expand the patterns
More informationFREEBIRD THE ORIGINAL D.I.Y. ORNITHOPTER! Tools and Glue. Required Materials
Do not try to make your ornithopter using "household materials". If you want it to fly, you have to build it right. FREEBIRD THE ORIGINAL D.I.Y. ORNITHOPTER! Wingspan: 16 inches Weight: 1/4 ounce The Ornithopter
More informationHome Storage Projects
This is an excerpt from the book Home Storage Projects by Paul Anthony Copyright 2001 by The Taunton Press www.taunton.com KITCHEN WORK STATION IN MANY KITCHENS, counter space is at a premium. There just
More informationPart 1: Cut Accurate Segments. Segmented Turning School. By Jim Rodgers
Part 1: Cut Accurate Segments Segmented Turning School By Jim Rodgers 24 American Woodturner Winter 2005 Reprinted with permission American Association of Woodturners Ready to try your hand at segmented
More informationMONTANA STATE UNIVERSITY SCHOOL OF ARCHITECTURE WOOD SHOP SAFETY MANUAL. Craft Shop Manager Bill Clinton wclinton@montana.
MONTANA STATE UNIVERSITY SCHOOL OF ARCHITECTURE WOOD SHOP SAFETY MANUAL Craft Shop Manager Bill Clinton wclinton@montana.edu 994 4402 1 Policies and Procedures 1. Eye Protection Eye protection must be
More informationThe tablesaw may be your shop s most valuable cutting. Crosscut Sleds. Foolproof. Innovative approach guarantees perfect results
Foolproof Crosscut Sleds Innovative approach guarantees perfect results B Y A L A N T U R N E R The tablesaw may be your shop s most valuable cutting tool, but for precise, repeatable crosscuts it needs
More informationWine Rack & Glass Storage Bench Chris Gardner
Wine Rack & Glass Storage Bench Chris Gardner Quantity Length Width Material Part 2 48 16 3/4 birch plywood top, bottom 2 14 16 3/4 birch plywood sides 2 14 13 3/4 birch plywood support dividers 2 3 15
More informationRudder Repair and refinish
Rudder Repair and refinish Montgomery 23 Dauntless The before photograph A receipt found inside the boat showed a previous owner had enlisted a boat yard to perform maintenance on the rudder by shortening
More informationDining Tables by Kim Carleton Graves
This is an excerpt from the book Dining Tables by Kim Carleton Graves Copyright 2001 by The Taunton Press www.taunton.com Vineyard Table The vineyard table is almost as old a design as the trestle table,
More informationMicro. Pitts Special for the RFFS-100 by Chris O Riley
Micro Pitts Special for the RFFS-100 by Chris O Riley F1 F2 F3 F4 1 2 3 4 All wood 1/32 inch sheet unless otherwise stated. F1 F2 F3 F4 Small balsa blocks for LG reinforcement Small balsa blocks for LG
More informationGuidelines for Earthquake Bracing of Residential Water Heaters
Guidelines for Earthquake Bracing of Residential Water Heaters Department of General Services Division of the State Architect 1102 Q Street, Suite 5100 Sacramento, CA 95814 Phone: (916) 324-7099 Fax: (916)
More informationThe Bonelle Tool and Cutter Grinder
The Bonelle Tool and Cutter Grinder The grinder was constructed about 1987 and exhibited at the 89th Model Engineering exhibition where it was awarded a bronze medal (see ME Vol164 No 3868 page 273). Subsequently
More informationROVs in a Bucket Building an Underwater Robot. 3.0 ROV Thrusters & Propeller Attachment. 3.1 Propulsion
3.0 ROV Thrusters & Propeller Attachment 3.1 Propulsion ROV s move forward and back, up and down, and to the left and right. They can make all of these moves without the benefit of a rudder. With three
More informationHOW TO MAKE A MOTOR BRACKET
HOW TO MAKE A MOUNTING BRACKET FOR AN ELECTRIC MOTOR Often, brackets supplied with purchased items (e.g. electric motors or servos) are not ideally suited for fitting into our models or they are not supplied
More informationGear PEPSI CAN STOVE INSTRUCTIONS
Gear PEPSI CAN STOVE INSTRUCTIONS [NOTE: Updated Instructions are now available. The new stove is less likely to develop flame leaks and the fuel/air mixture is improved. Instructions for a simmer ring
More informationVolume of Pyramids and Cones
Volume of Pyramids and Cones Objective To provide experiences with investigating the relationships between the volumes of geometric solids. www.everydaymathonline.com epresentations etoolkit Algorithms
More informationTopSky DLG Installation Manual
TopSky DLG Installation Manual Attention: Because after the compound materials solidify, there will be ammonia iris on the surface, which affect the bonding strength afterwards. Please polish with sandpaper
More informationmanaging the segmented vessel base
the BASE-ics The tendency for wood to react to humidity changes and, as a result, change dimension has always challenged segmented woodturners. This is especially true in the vessel base area. Segmenters
More informationDuPont Surfaces DUPONT TM CORIAN SOLID SURFACE 12mm GAUGE STANDARDIZATION
DuPont Surfaces DUPONT TM CORIAN SOLID SURFACE PRODUCT ADVISORY TABLE OF CONTENTS PAGE SECTION 1 A. Introduction 2 B. Bull-nose edge treatment 3 C. Ogee edge treatment on stacked edges 4 D. Coved Backsplashes
More informationINSTRUCTION MANUAL TOOLS NEEDED FOR ASSEMBLY: OPTIONAL FINISHING MATERIALS: Champaign, Illinois (217) 398-8970 E-mail: partssupport@hobbico.
INSTRUCTION MANUAL Thank you for purchasing the Hobbico Ultra-Tote! You have purchased one of the finest values available in field support equipment. We think you will be impressed with the design and
More information39HQ Airovision Air Handling Units
39HQ Airovision Air Handling Units Mounting instructions CONTENTS 1 - TRANSPORT AND LIFTING INSTRUCTIONS... 3 1.1 - General... 3 1.2 - Transport and storage... 3 1.3 - Roof edge protection during transport
More informationGarage Workbench Plans
www.bobsplans.com Garage Workbench Plans Every home woodworker knows the importance of making efficient use of the available space in his or her shop. This workbench is designed to provide the maximum
More informationBeadboard Wall Bookcase
Beadboard Wall Bookcase Note: The maximum load for each shelf is 30lbs.This hanging system is meant for drywall/wood stud mounting only. If walls are concrete, brick or plaster, please consult your local
More informationHeavy Glass Frameless Shower Door With Return Panel
202 Anderson Ave., elvue, KS 66407 Phone: 800-669-9867 Fax: 800-393-6699 www.onyxcollection.com Heavy Glass Frameless Shower Door With Return Panel Full Showers with Return ench Seat with Return FRLSDRPL-0116
More informationThe Penturner s Corner
The Penturner s Corner For the past several months my articles have been geared to modifying slimlines. I do hope the articles have been helpful and several new modified slimline pens are being made. It
More informationHoosier Step Stool. America s leading woodworking authority. Step by Step construction instruction. A complete bill of materials.
America s leading woodworking authority Step by Step construction instruction. Hoosier Step Stool A complete bill of materials. Exploded view and elevation drawings. How-to photos with instructive captions.
More informationSURFACE AREA AND VOLUME
SURFACE AREA AND VOLUME In this unit, we will learn to find the surface area and volume of the following threedimensional solids:. Prisms. Pyramids 3. Cylinders 4. Cones It is assumed that the reader has
More informationHOW-TO LAY HARDBOARD OR PLYWOOD FLOOR OVERLAY
HOW-TO HOW-TO LAY HARDBOARD OR PLYWOOD FLOOR OVERLAY Most floor coverings, if laid over uneven wooden floors, will wear unevenly and look unsightly. The answer is to cover the old boards with hardboard
More informationINSTALLATION INSTRUCTIONS
Turbo Tube Slide INSTALLATION INSTRUCTIONS C A U T I O N Do not climb on the outside of the slide This slide is designed for home use only, not for Public Playgrounds PlayCore, Inc. 2004 Copyrighted Material.
More informationDave s Sheet Metal Bending Brake
Dave s Sheet Metal Bending Brake I started building a Zenith CH601XL from plans in mid January 2006. After several failed attempts to bend the rudder spar I ended up going to a local sheet metal shop for
More informationTraditional Sonar and DSI Sonar Installation
Traditional Sonar and DSI Sonar Installation This document covers the installation of the transducer and display unit installation, which includes connecting the unit to power and installing the unit on
More informationSHOP NOTES METAL SHAPER FOR YOUR SHOP
SHOP NOTES METAL SHAPER FOR YOUR SHOP A METAL SHAPER is indispensable for certain machining operations where flat surfaces must be produced within very close limits, such as machining flats on castings,
More informationYou can copy, share or publish this document without changing this page and document content. Contact information eacubukcu@yahoo.
This is a traditional japanese puzzle box. But I prepared this document. All the copyrights of this docoments belongs to me. Document copyrights Erhan Çubukcuğlu 2015 You can copy, share or publish this
More informationLay blocks with mortar
Student Lay blocks with mortar What you will learn When you have fi nished this section, you should be able to: Mix mortar Lay blocks with correct mortar joints. How do I mix mortar? Mortar is a wet paste
More informationPlumbing. www.armeg.co.uk. The convenient, compact and clever solutions to your wrench and hand tool needs
INNOVATIVE DRILLING & TOOL SOLUTIONS www.armeg.co.uk Plumbing The convenient, compact and clever solutions to your wrench and hand tool needs Complete Heating Installation with PHI Wrench Set Easy Tap
More informationValley fold 1/4 at the left side, again creasing only at the edge, and unfold. Valley fold, connecting the tops of the angle bisectors, and unfold.
Triceratops by Jerry Harris 1. Begin with a square, white side up, with the vertical diagonal precreased. A square of 10" results in a model of approximately 5.8" long and 1.67" tall at the hip. 2. 3.
More informationBuild a Junior Solar Sprint Model Car Kit Materials: 1 PITSCO Ray Catcher Sprint Kit or Solar Made Junior Solar Sprint Kit 1 White Sheet of Plastic
Build a Junior Solar Sprint Model Car Kit Materials: 1 PITSCO Ray Catcher Sprint Kit or Solar Made Junior Solar Sprint Kit 1 White Sheet of Plastic Coated Paper 2 Balsa Sheets (10-1/2 x4 x3/16 ) 2 Alligator
More information