Product Installation Guide

Transcription

1 Perpendicular to Deck/Parallel Beam Gap for Gypsum Board - Full Height Wall - Flute Fill stuff "oversized plugs" before stud and bottom track - 6" and wider cut plug in half and install from each side - No caulk/spray required over mineral wool - Accommodate thickness of applied fire proofing required on Beam - Consider gap for layers of gypsum between Fire Proofing and Framing - Refer to UL Listing: HW- D Fastener Attachment 24" O/C max. Mineral Wool Flute Fill 5/8" Type X 1, 2, 3 Layers for 1, 2, 3 Hr Rating (When Exists) Fastener below Obstruction Max 24" from O/H 1

2 Parallel Underneath Beam - Offset Leg Profile Option - Use BlazeFrame offset leg profile - Install prior to fire proofing (no z- clips required) - Order upper leg of track to thickest Fire Proofing required (one size fits all) - Scrape fire proofing materials away to top of intumescent - Refer to UL Listing: HW- D Metal Pan Deck Fire Proofing (Thickness by Others) Structural Steel Support Fastener Attachment 24" O/C max. "OL" - Series 5/8" Type X 2

3 Parallel Cantilevered Under Beam - 14ga Angle or Flat Stock Outrigger with BlazeFrame Offset Leg profile - Assemble Outrigger to Offset Leg profile on ground - Attach Outrigger/Offset Leg assembly to underside of Beam before fire proofing - Fire proof beam filling area above Outrigger/Offset leg assembly - Scrape fire proofing materials away to top of intumescent - Refer to UL Listing: HW- D Metal Pan Deck Fire Proofing (Thickness by Others) Structural Steel Support Min. 14ga strap/angle fastened to web and opposing offset leg Fastener Attachment 16" O/C max. "OL" - Series 5/8" Type X 3

4 Parallel Under Beam - Z- Clips and Standard Profile Option - Use Z- Clips and standard BlazeFrame profile - Fill and seal all voids above BlazeFrame with additional fire proofing or caulking materials - Refer to UL Listing: HW- D Metal Pan Deck Fire Proofing (Thickness By Others) Structural Steel Support Z-Clip Attachment Clips (16" O/C) Fastener Attachment into Z-Clips 16" O/C 5/8 Type X 4

5 Parallel Under Beam - Attach through Fire Proofing Option - Fire Proofing less than 1" - attach through Fire Proofing standard BlazeFrame profile - Fastener attachment and load capacity per fastener manufacturer - Fill and seal all voids above BlazeFrame with additional fire proofing or caulking Metal Pan Deck Fire Proofing (Thickness By Others) Structural Steel Support Z-Clip Attachment Clips (16" O/C) Fastener Attachment into through Fire Proofing 5/8 Type X 5

6 Beam Penetration - "Horse shoe" Framing around Beam - Fire proofing or mineral wool "beam pocket fill" - Square cut drywall around beam - See Additional Install Framing Methods/Options: - Appendix A - Offset Leg Assembly - Fire Proofing Flute Fill - (Install Pre- Fire Proofing) - Appendix B - Snipped Single Track - Mineral Wool Flute Fill - (Install Post Fire Proofing) - Appendix C - Tabbed Track Assembly - Mineral Wool Flute Fill - (Install Post Fire Proofing) Metal Pan Deck Angle or Z-clip attached to beam or Steel Track Frame BlazeFrame Composite Fire Proofing or Mineral Wool only encompass angle or z-clip 5/8 Type X 6

7 Parallel to Flute - Flute Cover (No Mineral Wool Required) - Install BlazeFrame FC (flute cover) over fluted areas - No wool required above - Fasten BlazeFrame Profile to Flute Cover - Open end conditions "cap" with min 4 length of Mineral Wool compressed 33% Fastener Attachment 16" O/C max. Fastener Attachment 24" O/C max. BlazeFrame (FC) Flute Cover (Continuous) 5/8 Type X Min. 4 pcf Mineral Wool Compress min. 33% Extend min. 4" inward into flute above Flute Cover Concrete Fill Min. 4 pcf Mineral Wool Compress min. 33% Extend min. 4" inward into flute above Flute Cover 5/8 Type X 7

8 Install Exterior Corner - ECA (End Cap Angle) Clips Single, Chase, and Shaft Wall (Head, Vertical, & Bottom Joint Protection)- - Keep track ends butted - Exposed "finished look" gaps in substrate apply bead of black caulk (no daylight pass through) Install Exterior Corner - use ECA (End Cap Angle) Clips Insert ECA into track Side View Insert ECA into track ECA inside track attached with fastener Intersecting wall BlazeFrame butted against intumescent Drywall Installation - Notch or slot "slider sheet " corner to accommodate intersecting tracks Notched Drywall "Corner Void" "Slot Accomodate Track leg" Depth of Track Leg Depth of Track Leg Width of Track Profile Width of Track Leg 8

9 Install "Offset Jog" in wall layout Insert ECA into track Intumescent of oppsing ECA Profiles in "butted" contact Install "Large Offset Jog" in wall layout BlazeFrame ECA (End Cap Angle) BlazeFrame OSA or IANF Span outer leg to outer leg BlazeFrame OSA or IANF Span inner leg to inner leg BlazeFrame ECA (End Cap Angle) BlazeFrame Track Profile 9

10 Bypass Framing for "Cast in Place" or Vertical Cavity Obstructions eliminate Web Cut Outs Option A - Inside Angle Bypass ISAF (Slotted Vertical Leg) Profile IANF (Solid Vertical Leg) Profile 1.25" 1.25" (L) (I) (S) (L) (I) I = Intumescent Strip Width - (to Match Opposing Track Profiles) Side View Cast in Place Bypass Concrete Wall Cavity Penetration (i.e. conduit/pipe) BlazeFrame Profile BlazeFrame ISAF or IANF Profile Vertical Floor Penetrations (i.e. conduit/pipe) BlazeFrame Profile BlazeFrame "ISAF" or "IANF" Profile BlazeFrame Profile 10

11 Option B - Utilize FSP (flat strap patch) to patch "leg cut out" Side View BlazeFrame FSP (Flatstrap Patch) Fasten FSP to outer surface of track leg 11