Swash plate pumps the key to the future

Transcription

1 Group 3 - Pumps Paper Swash plate pumps the key to the future Dipl.-Ing. Gordon Mohn Bosch Rexroth AG, An den Kelterwiesen 14, D Horb am Neckar, [email protected] Dr.-Ing. Timo Nafz Bosch Rexroth AG, An den Kelterwiesen 14, D Horb am Neckar, [email protected] Abstract Due to many advantages, swash plate pumps are wide spread in hydraulic systems. The main advantages are the through drive capability, the adjustability and most of all, the high power density. Their application range is limited, historically, to 450bar including medium and higher volume sizes. In higher pressure range, constant pumps such as wobbling disks or radial piston pumps are normally used. This is because the higher stressed parts can be dimensioned much bigger. Pumps with lower power such as constant displacement gear pumps are generally used in low price applications. In order to enlarge the application range of swash plate pumps, their advantages have to be further improved and strengthened. This paper shows by example how the pressure of the basic series A4VSO was increased up to a nominal pressure of 630bar and the historical pressure mark of 450bar could be exceeded. This increase in pressure level enables for example steel treatment manufacturers to reduce their component sizes without the need of a pressure transducer. Furthermore the power density of the redesigned HA4VSO was increased by 36%, compared to the standard A4VSO, by significantly increasing the self-priming speed. On the other side of the application range, in lower power mobile applications such as small tractors, forklift and skid steer loader, there is an increasing demand for less exhaust emissions and better fuel economy. The energy saving potential by changing from a hydraulic system with constant hydraulic pumps to variable hydraulic pumps is already proven on high power applications. By developing the variable axial piston pump A1VO to the requirements of lower horse power application, it is now also possible to realize such savings in lower horse power applications. Furthermore efficiency of the pump itself can be improved. An example of this is shown by way of the new A4 series 33. KEYWORDS: swash plate pump, power density, efficiency, speed, pressure

2 140 10th International Fluid Power Conference Dresden Historical application range The swash plate pump is a long-known design, cf. /1/. Because of wear problems in earlier development stages, high quantities were only reached in the last few decades. Today, the swash plate design is deemed to be the most significant hydrostatic piston machine /2/, /3/. The advantages of axial piston pumps with swash plate design is the high nominal pressure level, variability of the displacement, beneficial efficiencies, through drive capability and low mass of inertia. Typically, swash plate pumps are used in applications with high technical requirements, for example construction, agricultural and industrial machinery /4/. Figure 1 shows that in comparison to other pump designs, the axial piston pump design is characterized by the highest efficiencies with typical applications for middle to high pressure ranges, traditionally used in mobile and industrial hydraulics. The specific speed n q on the x-axis is a function of the speed, flow and specific pump work. Figure 1: Extended Cordier diagram /5/ Besides the nominal pressure, more characteristics are relevant for an excellent hydrostatic drive. These are the duration ratio at maximum power, the power ratio, efficiency, speed ratio at atmospheric inlet pressure, the number of possible operation modes as well as the required controllers. Another important criteria, noise, is discussed in /6/ and therefore not included in this paper.

3 Group 3 - Pumps Paper Strengthening the strength of swash plate pumps: power density The performance criteria concerning the rotary group can be summarized to power density. This is also the main strength of swash plate pumps and therefore the key to the future. In order to increase this strength of swash plate pumps even more, power density needs to be increased even more: (1) Equation (1) shows the guideline for the further development of swash plate pumps. Therefore we see four directions to develop. Operating pressure needs to be increased, as well as speed increased, efficiency optimized and the packaging (Vg/m) improved. Furthermore, this performance has to be produced within a reasonable cost range to provide an optimal Total Cost of Ownership to the customer. In the following it is shown, how recent developments at Bosch Rexroth meet these requirements in increasing the strength of swash plate pumps and build the key to the future Rising the pressure level Especially in steel plants high pressures are demanded in order to keep the sizes of the cylinders and the framework as small as possible. In order to do so, expensive pressure intensifiers are needed to increase the pressure up to a typical level of well above 600bar. In order to reduce the installation equipment, a high pressure pump is required, that directly provides such a high pressure level. Figure 2: Reduced installation equipment in steel plants with A4VHO450

4 142 10th International Fluid Power Conference Dresden 2016 To fulfil this requirement the development of the new A4VHO was started. The intention is to provide a pump that can handle a nominal pressure of 630bar and a maximum pressure of 700bar. This development is based upon the A4VS family which can already handle a nominal pressure level of 450bar in the A4VBO version. Figure 3: A4VHO450 as new member of the A4VS family This new pressure level leads to very high contact pressures inside the rotary group and therefore many improvements have been carried out. For example, a specially formed contour in the slipper pads was introduced in order to reduce the stress and handle higher loads. With this new design, stress was reduced significantly, making the slipper pad suitable for pressure peaks up to 700bar. Another very important task is the balancing of the cylinder barrel, which was not designed for 700bar initially. Logically the optimal design for the feed-through in the cylinder barrel are circular holes. Furthermore the hydraulic balancing varies with the alternating piston forces, due to the odd number of pistons. This gets even more important, when coming to higher pressures. In order to have a very well balanced and stable running cylinder barrel, the balancing was designed in a totally new way. With this new design, hydraulic balancing is adapted to the alternating piston forces and therefore no longer varies significantly. This enables the cylinder barrel to run very smoothly. In order to qualify the pump for a maximum pressure of 700bar a special test was set up. Both pumps were set up as a tandem unit with one driveshaft, one unit operating as pump and the other unit operating as motor. The high pressure side was fed directly from the pump into the motor via a steel pipe. In this way standard testing equipment could be used and the secondary unit is already tested in motor mode.

5 Group 3 - Pumps Paper Figure 4: Testing the A4VHO for peak pressure 700bar With this features and testing technique, the first commercially available swash plate pump A4VHO for peak pressures up to 700bar was developed Increasing speed Increasing the speed of swash plate pumps gives the customer the opportunity to downsize installed electrical engines and therefore reduce their installation costs significantly. Especially if the pump can operate at ambient pressure and no boost of the suction is required. The development of the new HA4VSO was therefore started. The intention is to provide a pump that operates at ambient pressure of 1barA and can provide 250l/min at a speed of 3.600rpm. This development is based upon the A4VSO family. Figure 5: HA4VSO as member of the A4VS family This increase of speed of 36% compared to the standard version demands a very good suction performance of the rotary group and of the entire suction line. This development only became possible due to new design methods such as CFD-simulation. A very important part in this optimization are the oil flow conditions from the suction line into the

6 144 10th International Fluid Power Conference Dresden 2016 cylinder barrel. This task was optimized using Computational Fluid Dynamics technology (CFD). In this way, suction conditions were improved significantly. Figure 6: CFD simulation of cylinder barrel and suction line Considering the complete suction installation of the customer's application is just as important. The entire pressure loss from tank to cylinder barrel was considered in the CFD-Analyses. This and more optimizations lead to the first pump size 71 that can operate at 3.600rpm at full stroke and ambient pressure. This results in a significant increase of power density of 36% compared to the standard version, which gives a huge advantage to the customer and his applications Increasing Efficiency Thinking ecologically and economically it is important for hydraulic systems to have high efficiency. In this paper two examples are shown, how the swash plate pump can firstly, improve the efficiency of the system and secondly, how its own efficiency can further be improved System Efficiency Every hydraulic system has to be set up according to the maximum required horse power. This includes the hydraulic pumps which have to be selected to fulfil the maximum flow and pressure demand. The open-center hydraulic system is still used in low power mobile machinery because of the low installation costs. As long as the system is running at the maximum flow and maximum pressure the efficiency is good. Looking at the load cycle of many applications, most of the time full flow and full pressure is not needed. During these periods constant pumps are still generating full flow at maximum pressure, which leads to a high loss of energy.

7 Group 3 - Pumps Paper Open-center with constant hydraulic pump Load sensing with constant hydraulic pump Load sensing with variable hydraulic pump pressure Power loss pressure Power demand Power loss Power demand flow flow flow Figure 7: Hydraulic systems with constant and variable hydraulic pump pressure Power loss Power demand One step towards a better efficiency is a load sensing hydraulic system, with constant hydraulic pumps. As opposed to the open-center, the hydraulic system is sensing the pressure demand and is lowering the pressure level according to the required level. Nevertheless the generated flow cannot be adjusted, which leads to energy losses during these working conditions. Only by using a variable displacement pump, is it possible to adjust the pressure and flow in all working conditions to the real demand of the hydraulics system. In high power applications open-center systems with variable hydraulic pumps are state of the art and have already proven the huge potential of energy saving. Actual analyses of low power application load cycles show that there is a big energy saving potential, too. The following figure shows a typical load cycle of a 90 hp tractor. Figure 8: Load cycle distribution

8 146 10th International Fluid Power Conference Dresden 2016 Variable axial piston units open up significant saving potentials in the partial load range. This includes all work which does not demand full hydraulic power, such as vibration damping of the attachment, the chassis and the cabin while traveling on field and road. Also steering movements or various other activities in the yard and the field. Accounting for more than two thirds of the time, such operations considerably outweigh the times under full load or in standby mode when the possible savings are nearly zero due to system considerations. The engine characteristics of the diesel can be used to calculate the actual fuel consumption per cycle, enabling a comparison between a variable displacement pump and a constant displacement pump. The maximum savings result as shown in the table when the diesel motor only provides as much power as actually needed. Figure 9: Maximum savings potential per operating hour Based on this typical tractor load cycle fuel savings between 10 and 15 % per operating hour in mixed use is realistic. Assuming a life time of 6,000 hours for the tractor, this translates into fuel savings of up to 10,000 liters. Similar calculations have been made for a typical forklift application. Based on the Transport & Opslag-cycle, a de-facto standard load profile for forklift trucks, the expected fuel savings amount to 0.7 liters per hour. This translates into approximately 7,000 liters of fuel savings during the 10,000 hours of typical machine life of a forklift truck. When comparing a variable hydraulic pump fan drive with a conventional belt drive, the savings potential becomes evident. Based on the typical fan drive duty cycle in a combine harvester, as provided by a major manufacturer, the calculations show a fuel saving of 3.9 liters per hour which results in over 29,000 liters during the average life time of 7,500 hours.

9 Group 3 - Pumps Paper Depending on the respective load cycles, similarly great fuel savings can be achieved in many other application areas and all without sacrificing performance Pump Efficiency If the system is already optimized for high efficiency, energy consumption can be further improved by increasing the efficiency of the swash plate pump. Therefore, the new A4VSO / VSG / CSG series 33 is specially optimized for efficiency. The first step for this improvement is to know, where the losses occur. Figure 11 shows the distribution of the power loss in a swash plate type piston pump. Figure 10: Distribution of power losses in a swash plate type compact pump The importance of the piston contact is described in /7/. Furthermore, splashing losses show a huge potential to further improve the efficiency as also shown in /8/ and /9/. Regardless, a totally empty housing is not preferred since the bearings and shaft seals need to be lubricated and cooled. A detailed analysis of the splashing losses was therefore performed and validated with measurements. Figure 11: CFD simulation of the splashing losses in a swash plate piston pump

10 148 10th International Fluid Power Conference Dresden 2016 In this detailed simulation the location of the main splashing losses was identified and solutions were found to improve the splashing losses significantly without needing an empty housing. This and more features are implemented in the new A4VSO/VSG/CSG series 33 and lead to a significant improvement in total pump efficiency. Figure 12: Efficiency diagramm A1VO The A1VO proves that closing the price gap to a constant pump does not mean making any compromises on performance or efficiency. The internal hydrodynamic bearings such as cylinder / piston, cylinder / distributor plate, piston shoe / swashplate are optimized to realize a maximum overall efficiency well above 90% and a high efficiency level in a wide range of operation Total cost of ownership and pump pricing To perform transition of lower power mobile machinery to an energy efficient load sensing system with variable displacement pumps, the key to success is to close the price gap to open-center systems and load sensing with constant pumps. The A1VO enables such an attractive price/performance ratio by significantly reducing the number of different variants, moving all ports to one part, reducing the amount of internal parts. Also the optimized design allows for an efficient high quantity production and assembly. Figure 13: Variable displacement pump A1VO

11 Group 3 - Pumps Paper Conclusion The measures shown in this paper make the swash plate pumps the key to the future. The main advantages are through drive capability, adjustability and most of all the high power density. It is shown how the already high power density can be increased even further by increasing pressure, speed and efficiency. The paper shows by example how the pressure of the A4VSO basic series was increased up to a nominal pressure of 630bar which is a pressure increase of 40% compared to the A4VBO. Furthermore the suction speed at ambient pressure of the new HA4VSO is increased by 36% compared to the standard A4VSO. Additionally, the new A4VSO series 33 gives significantly higher efficiency than its predecessor series 30. The energy saving potential by changing from a hydraulic system with constant hydraulic pumps to variable hydraulic pumps is already state of the art. By optimizing the variable axial piston pump A1VO to the requirements of lower horse power application, it is now possible to realize such savings in lower horse power applications, as well. The A1VO proves that closing the price gap to a constant pump does not mean making any compromises on performance or efficiency. All these measures make the swash plate pump the key to the future. 4. References /1/ Patentschrift, DE A, 1928 /2/ Forster, F., Welschof, B., Den Schrägscheiben gehört schon immer die Zukunft, O+P Zeitschrift für Fluidtechnik 48, Nr. 8, 2004 /3/ Matthies, H. J., Renius, K. T., Einführung in die Ölhydraulik, Vieweg+Teubner Verlag, 7. Auflage, 2011 /4/ Ivantysyn, J. u. M., Hydrostatische Pumpen und Motoren, Konstruktion und Berechnung, Vogel Buchverlag, 1993 /5/ Grabow, G., Optimalbereiche von Fluidenergiemaschinen - Pumpen und Verdichter, Forschung im Ingenieurswesen 67, Springer-Verlag, 2002 /6/ Nafz, T., Aktive Ventilumsteuerung von Axialkolbenpumpen zur Geräuschreduktion hydraulischer Anlagen, Dissertation, RWTH Aachen University, IFAS, Germany, 2011

12 150 10th International Fluid Power Conference Dresden 2016 /7/ Gels S., Einsatz konturierter und beschichteter Kolben-Buchse-Paare in Axialkolbenmaschinen in Schrägscheibenbauweise, Dissertation, RWTH Aachen University, IFAS, Germany, 2011 /8/ Jang D. S., Verlustanalyse an Axialkolbeneinheiten, Dissertation, RWTH Aachen University, IFAS, Germany, 1997 /9/ Enekes K., Ausgewählte Maßnahmen zur Effizienzsteigerung von Axialkolbenmaschinen, Dissertation, RWTH Aachen University, IFAS, Germany, Nomenclature m n Peff Δp Vg Φ η mass drive speed effective output power pressure difference geometrical stroke volume power density efficiency