4 CHANNEL DVR. User Manual SDE-3004

Transcription

1 4 CHANNEL DVR User Manual SDE-3004

2 4 Channel DVR User Manual Copyright 2012 Samsung Techwin Co., Ltd. All rights reserved. Trademark is the registered logo of Samsung Techwin Co., Ltd. The name of this product is the registered trademark of Samsung Techwin Co., Ltd. Other trademarks mentioned in this manual are the registered trademark of their respective company. Restriction Samsung Techwin Co., Ltd shall reserve the copyright of this document. Under no circumstances, this document shall be reproduced, distributed or changed, partially or wholly, without formal authorization of Samsung Techwin. Disclaimer Samsung Techwin makes the best to verify the integrity and correctness of the contents in this document, but no formal guarantee shall be provided. Use of this document and the subsequent results shall be entirely on the user s own responsibility. Samsung Techwin reserves the right to change the contents of this document without prior notice. Design and specifications are subject to change without prior notice. The default password can be exposed to a hacking thread so it is recommended to change the password after installing the product. Note that the security and other related issues caused by the unchanged password shall be responsible for the user.

3 overview IMPORTANT SAFETY INSTRUCTIONS Read these operating instructions carefully before using the unit. Follow all the safety instructions listed below. Keep these operating instructions handy for future reference. 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this apparatus near water. 6) Clean only with dry cloth. 7) Do not block any ventilation openings, Install in accordance with the manufacturer s instructions. 8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9) Do not defeat the safety purpose of the polarized or grounding- type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. if the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11) Only use attachments/accessories specified by the manufacturer. 12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 13) Unplug this apparatus during lightning storms or when unused for long periods of time. 14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. OVERVIEW English _3

4 overview CAUTION RISK OF ELECTRIC SHOCK. DO NOT OPEN CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol indicates that dangerous voltage consisting a risk of electric shock is present within this unit. This exclamation point symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture. To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the installation instructions. WARNING 1. Be sure to use only the standard adapter that is specified in the specification sheet. Using any other adapter could cause fire, electrical shock, or damage to the product. 2. Incorrectly connecting the power supply or replacing battery may cause explosion, fire, electric shock, or damage to the product. 3. Do not connect multiple cameras to a single adapter. Exceeding the capacity may cause abnormal heat generation or fire. 4. Securely plug the power cord into the power receptacle. Insecure connection may cause fire. 5. When installing the camera, fasten it securely and firmly. The fall of camera may cause personal injury. 6. Do not place conductive objects (e.g. screwdrivers, coins, metal parts, etc.) or containers filled with water on top of the camera. Doing so may cause personal injury due to fire, electric shock, or falling objects. 7. Do not install the unit in humid, dusty, or sooty locations. Doing so may cause fire or electric shock. 8. If any unusual smells or smoke come from the unit, stop using the product. In such case, immediately disconnect the power source and contact the service center. Continued use in such a condition may cause fire or electric shock. 9. If this product fails to operate normally, contact the nearest service center. Never disassemble or modify this product in any way. (SAMSUNG is not liable for problems caused by unauthorized modifications or attempted repair.) 10. When cleaning, do not spray water directly onto parts of the product. Doing so may cause fire or electric shock. 11. Do not expose the product to the direct airflow from an air conditioner. Otherwise, it may cause moisture condensation inside the Clear Dome due to temperature difference between internal and external of the dome camera. 12. If you install this product in a low-temp area such as inside a cold store, you must seal up the wiring pipe with silicon, so that the external air can not flow inside the housing. Otherwise, external high, humid air may flow inside the housing, pooling moisture or vapor inside the product due to a difference between internal and external temperature. 4_ overview

5 BEFORE START This user manual provides Information for using the DVR such as brief introduction, part names, functions, connection to other equipment, menu setup, etc. You have to keep in mind the following notices : SAMSUNG retains the copyright on this manual. This manual cannot be copied without SAMSUNG s prior written approval. We are not liable for any or all losses to the product incurred by your use of non-standard product or violation of instructions mentioned in this manual. Prior to opening the case, please consult a qualified technician first. Whenever this is needed power must be removed from the unit. Before installing an additional HDD or connecting an external storage device (USB HDD) to this DVR, check the compatibility. Consult your provider for the compatibility list. Warning OVERVIEW Battery It is essential that when changing the battery in the unit, the replacement battery must be of the same type otherwise there may be a possibility of an explosion. The following are the specifications of the battery you are using now. Normal voltage : 3V Normal capacity : 170mAh Continuous standard load : 0.2mA Operating temperature : -20 C ~ +85 C (-4 F ~ +185 F) CALIFORNIA USA ONLY This Perchlorate warning applies only to primary CR (Manganese Dioxide) Lithium coin cells in the product sold or distributed ONLY in California USA. Perchlorate Material - special handling may apply, See Caution Connect the power cord into a grounded outlet. The Mains plug is used as a disconnect device and shall stay readily operable at any time. Batteries shall not be exposed to excessive heat such as sunshine, fire or the like. Risk of Explosion if Battery is replaced by an Incorrect Type. Dispose of Used Batteries According to the Instructions. System Shutdown Turning off the power while the product is in operation, or undertaking improper actions may cause damage or malfunction to the hard drive or the product. Please turn off power by pressing the [POWER] button on the remote control or right-click to display the context sensitive menu and select <Shutdown>. After selecting <OK> in the pop-up menu, you can pull off the power cord. You may want to install a UPS system for safe operation in order to prevent damage caused by an unexpected power stoppage. (Any questions concerning UPS, consult your UPS retailer.) Operating Temperature The guaranteed operating temperature range of this product is 0 C ~ 40 C (32 F ~ 104 F). This product may not work properly if you run right after a long period of storage at a temperature below the guaranteed one. Prior to using a device that has been stored for a long period in low temperatures, allow the product to stand at room temperature for a period. Especially for the built-in HDD in the product, its guaranteed temperature range is 5 C ~ 55 C (41 F ~ 131 F). Likewise, the hard drive may not work at a temperature below the guaranteed one. English _5

6 overview CONTENTS OVERVIEW 3 3 Important Safety Instructions 5 Before Start 6 Contents 8 Features 10 Part Names and Functions (Front) 11 Part Names and Functions (Rear) 12 Remote Control CONNECTING WITH OTHER DEVICE Installation 13 Checking the installation environment 13 Connecting the Video, Audio, and Monitor 14 Connecting the USB 14 Connecting the Camera 17 Connecting the Network LIVE Getting Started 21 Live Screen Configuration 25 Live Mode 27 Spot Out 27 Zoom 28 Audio ON/OFF 28 Freeze 28 Event Monitoring USING THE DVR System Setup 40 Setting the Device 46 Setting the Recording 49 Setting the Event 52 Backup 53 Network Configuration 6_ overview

7 SEARCH & PLAY Search 63 Playback WEB VIEWER Introducing Web Viewer 66 Connecting Web Viewer 67 Using Live Viewer 71 Using Search Viewer 75 Viewer Setup 85 About 85 Mobile Viewer OVERVIEW BACKUP VIEWER SEC Backup Viewer APPENDIX Product Specification (Camera) 89 Product Specification 91 Default Setting 94 Troubleshooting 96 Open Source License Report on the Product English _7

8 overview FEATURES The DVR employs H.264 video encoding for 4 channel inputs and audio encoding for 1 channels while simultaneously supports hard disc recording and playback. These DVRs also supports network connectivity, providing remote monitoring from a remote PC transferring video and audio data. Provides a convenient User Interface Supports CIF(S)/2CIF(M)/4CIF(L) recording formats With the network specific codec, network transfer enabled regardless of the recording conditions De-interlacing processor for better picture quality Display of HDD information and status by using HDD SMART Hard Disk overwrite function Mass storage hard disk backup through high-speed USB 2.0 Simultaneous Record and Playback of 4 channel video data Various Search Modes (Search by Time, Event, Backup and Motion Detection) Various Recording Modes (Time Lapse, Event, Scheduled Recording) Remote Monitoring function by Network Viewer and Mobile Viewer 8_ overview

9 POWER REC DIGITAL VIDEO RECORDER Standards Approvals M This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Package Contents Please unwrap the product, and place the product on a flat place or in the place to be installed. Please check the following contents are included in addition to the main unit. OVERVIEW DVR Adapter Power Cable Mouse Remote Control / Battery (AAA x 2) SEB-1020R (x4) Bracket (x4) Screws (x12) Expansion pipe (x12) Camera Cable (x4) Network Cables Quick Guide Warranty Card User Manual & Quick Connect Program CD English _9

10 overview PART NAMES AND FUNCTIONS (FRONT) DIGITAL VIDEO RECORDER POWER REC b c Part Names Functions USB Port b Remote Control Receiver c LED Indicator Connects the USB devices. Input the remote control signal. Power LED : Displays the power ON/OFF status. REC : Lights on when recording is in progress. 10_ overview

11 PART NAMES AND FUNCTIONS (REAR) b c 1 2 AUDIO IN NETWORK DC 12V 3 4 ALARM IN ALARM OUT G 1 COM G CONSOLE VIDEO OUT AUDIO OUT VGA USB OVERVIEW Part Names CAMERA IN b VIDEO OUT c AUDIO IN NETWORK DC 12V USB VGA AUDIO OUT Functions Video Signal input ports (BNC type connector). Video Signal Output Port (RCA jack). Audio input signal port (RCA jack, CH1). NETWORK connector port. DVR power input port. USB connector port. VGA Video Signal Output Port. Audio Signal Output Port (RCA jack). M [CONSOLE] is designed for the service repair purpose only. If using the VGA cable, the source from VGA will be displayed as main image on the screen along with the OSD menus. Then, the BNC port will output the video signal alone. If not using the VGA cable, the source from BNC will be displayed as main image on the screen along with the OSD menus. If you connect the VGA cable after the system boot, only the video signal from VGA will be displayed. English _11

12 overview REMOTE CONTROL SEARCH Displays the search menu. BACKUP Displays the Backup Menu. MODE Changes the screen mode. POWER Displays the Exit pop up screen. DVR Activates the DVR function. NUMBER [0~+10] Used as the numeric input keys, or displays a single channel. Skip Backward (by unit time), Slow Rewind, Slow Forward, Skip Forward (by unit time) T/W Zooms in or out. MENU Goes to the system menu screen. ID Sets the ID of the system. Select 2 digits from 0 ~ 9 while pressing the ID Key. Move Frame While paused, moves to the previous/next frame. FR, STOP, PLAY/PAUSE, FF SCROLL,. Moves the menu scroll. RETURN Returns to the previous screen. Up/Down/Left/Right( )/ENTER Moves the cursor up/down/left/right, and runs the Select Menu. FREEZE Freezes the screen temporarily. ZOOM Runs the digital zoom (x2) function. REC Starts or ends the live recording. AUDIO Turns Audio on/off. ALARM Cancels the Alarm. REC LOCK Selects the recording lock function. PIP Selects or deselects the PIP function. EP Using the Numeric buttons 1. Press any button among 1 to Move to the selected channel number. Changing the Remote Control ID 1. Press the ID button of the remote control and check the ID displayed on the DVR screen. The factory default ID of the remote control is Enter 2 digits of your selection in order, while pressing the system [ID] button. 3. When ID input is done, press the system [ID] button again to check the setting. M If you want to change the remote control ID to 08: Press 0 and 8 in order while the system [ID] button is pressed. Remote control's ID and DVR s ID should be matched for proper operation. Refer to Remote Devices. (Page 43) 12_ overview

13 VIDEO OUT AUDIO IN CONSOLE NETWORK DC 12V connecting with other device INSTALLATION Please take note of the followings before using this product. Do not use the DVR outdoors. Do not spill water or liquid in the connection part of the product. Do not impose the system to excessive shock or force. Do not pull out the power plug forcefully. Do not disassemble the product on your own. Do not exceed the rated input/output range. Use a certified power cord only. For the product with an input ground, use a grounded power plug. CHECKING THE INSTALLATION ENVIRONMENT Samsung Digital Video Recorder ( DVR hereinafter) is a state-of-art security device, and contains mass storage hard disk(s) and critical circuits inside. When the temperature rises inside the product, the product may breakdown and the product life be shortened. Temperature Unit: ºC One Year: 24HR X 365 DAY =8,760 HR CONNECTING WITH OTHER DEVICE Life (Unit: HOURS) CONNECTING THE VIDEO, AUDIO, AND MONITOR AUDIO OUT ALARM IN ALARM OUT G 1 COM G VGA USB M Only one mouse port is available. English _13

14 connecting with other device CONNECTING THE USB 1. By factory default, a USB port is provided for external connection. 2. You can connect a USB HDD, USB memory or mouse to the USB port. 3. If a USB HDD is connected to the system, recognition and settings are available in Menu > Setting the Device > Storage Device. (Page 41) 4. This product supports hot-plugging, which connects/removes the USB device during the system operation. J If you use the USB device for Backup purposes, format it with FAT32 on PC if it is not formatted on the DVR. CONNECTING THE CAMERA Equipped with the IR LED and the illumination sensor, enables you to monitor at night as well as in daytime. The camera is suitable for both internal and external use. Please make sure not to fully expose the camera to rain. The camera must be installed under a shelter to avoid exposure to excessive rain or moisture. b c Name Description IR LED b Lens c Illumination Sensor These infrared LED s are controlled by the illumination sensor. Focal length of 3.6mm enables you to cover relatively longer range of monitoring. Detects incoming light to control the IR LED. Camera Fitting Groove Groove that is used to fit the camera bracket. There are two grooves; one on the top and one on the bottom. BNC Cable Power Cable BNC terminal for video signal output. Used to plug the power cable. 14_ connecting with other device

15 VIDEO OUT Connecting with DVR TO DVR SIDE ONLY AUDIO IN TO CAMERA SIDE ONLY Installing the camera The camera can be installed on the wall, ceiling, shelf or a desired position using the provided bracket. 1. Select a position where you want to install the camera. Make sure the selected position can sustain the weight of the camera. AUDIO OUT VGA ALARM IN ALARM OUT G 1 COM G CONSOLE NETWORK USB DC 12V CONNECTING WITH OTHER DEVICE 2. Use the screw bolts (M3.5 X L25) to mount the camera bracket onto the wall or ceiling. 3. Place the camera on the selected position and fit the hole either on the top or the bottom of the camera into the fixing bolt of the bracket, and turn the camera clockwise. J You should be careful when installing the BOX camera outdoors because the cable connectors may be wet with moisture or pile up with impurities. The camera satisfies the IP65 standard, and direct exposure to water or moisture may cause problem such as condensation. M3.5 X L25 sized screws wall or ceiling Camera Bracket The camera bracket can be used to install the camera on the wall, ceiling or shelf. Camera Bracket Specification Name Description Use Installation Dimensions Weight Operating Temperature Accessories Indoor / Outdoor Wall or Ceiling Ø60 x H72mm (Ø2.36 x H2.83 inch) 85g (0.19 lbs) -10 C ~ 50 C (14 F ~ 122 F) SCREW (M3.5 X L25): 3 pcs for each bracket English _15

16 connecting with other device Adjusting the Camera Bracket 1. Choose an installation site that can sufficiently support the weight of the equipments to be installed. 2. Attach the camera bracket to the wall using the supplied screws (M3.5 X L25). 3.5 X 25 sized screws wall or ceiling. 3. Adjust the camera to target the video location and tighten the camera bracket handle on the camera bracket. Install the camera on to the male screw of the camera bracket by rotating the camera clockwise. 4. Loosen the handle by turning it counter clockwise and then adjust the camera position. Tighten the handle, turning it clockwise to lock the camera in position. 5. Connect the camera cable to the camera. Handle 16_ connecting with other device

17 VIDEO OUT AUDIO IN G 1 COM G NETWORK CONNECTING THE NETWORK Connecting to Network through Ethernet (10/100BaseT) Hub/Switcher NETWORK VIDEO OUT Back Bone AUDIO IN AUDIO OUT VGA ALARM IN ALARM OUT G 1 COM G RJ-45 Ethernet Cable (Direct Cable) Windows Network Viewer NETWORK CONSOLE USB Hub/Switcher DC 12V CONNECTING WITH OTHER DEVICE Connecting to the Network using the router AUDIO OUT ALARM IN ALARM OUT xdsl or Cable Modem VGA CONSOLE DC 12V USB NETWORK Broadband Router xdsl or Cable Modem Windows Network Viewer DDNS Server (Data Center) English _17

18 VIDEO OUT AUDIO IN G 1 COM G CONSOLE NETWORK DC 12V connecting with other device Connecting to Internet through ADSL AUDIO OUT ALARM IN ALARM OUT VGA INTERNET Phone(ADSL) Line RJ-45 Ethernet Cable (Direct Cable) USB ADSL MODEM Hub/Switcher Windows Network Viewer 18_ connecting with other device

19 live GETTING STARTED Starting the system 1. Connect the power cable of the DVR to the wall outlet. M It takes about 10 seconds to display the start screen after booting. LIVE 2. You will see the initialization screen. The initialization process will last about 1 minute. If a new HDD is installed, the initialization process may take longer. REC 3. The live screen appears with a beep :10: :10:25 Shutting Down the System You can shut down the system only if you have logged into the DVR. You require permission to shut down the system if you are not logged in as admin. 1. Press the [POWER] button on the remote control or right-click to display the context sensitive menu and select <Shutdown>. 2. The Shutdown confirmation window appears. Shutdown 3. Use the arrow keys on the remote control to move to <OK> and press the [ENTER] button or click <OK>. The system will shut down. 4. Disconnecting the power cable for power off and reconnecting the power cable to restart. M :10:25 Are you sure to shutdown? For the permission management, refer to Permission Management > Setting Permissions. (Page 35) OK Cancel English _19

20 live Login To access a DVR or restricted menu, you should have logged in to the DVR. 1. In live mode, right-click any area of the screen. You will see the context sensitive menu as in the right figure. Scene Mode :10:25 Spot Out Audio Off Freeze Stop Alarm Record Play Search Backup Main Menu Shutdown Hide Launcher Login 2. Click <Login>. The login dialog appears. You can also see the login dialog to access a desired menu by pressing the [MENU] button on the remote control. The login dialog will also appear if you press a menu button on the remote control of the DVR when the corresponding menu requires logging in. After logged in, press [RETURN] on the remote control to display the logout dialog. By default, initial ID and password are set to admin, and :10:25 Login ID admin Password OK Cancel J M The default password can be exposed to a hacking thread so it is recommended to change the password after installing the product. Note that the security and other related issues caused by the unchanged password shall be responsible for the user. For the restricted permission, refer to Permission Management > Setting Permissions. (Page 35) Locking All Buttons This will restrict access to all buttons available in the DVR. 1. In Live mode, press buttons in the order of [STOP (@)] [FREEZE] [STOP (@)] [FREEZE] [MENU]. All buttons will be locked. 2. In the lock condition, press any button to display a dialog where you are prompted to enter the password for unlocking the buttons. The button lock will be released if you enter the admin password :10:25 Key Lock Password ID admin Password OK Cancel 20_ live

21 LIVE SCREEN CONFIGURATION Icons on the Live Screen You can check the status or operation of the DVR with the icons on the live screen :10:25 LIVE CAM 01 Name Description Current Date, Time Displays the current time and date. b Login Information When you are logged in, the LOG ON icon will be displayed. Displayed if the zoom function is activated. c Screen Mode System Operation Displayed if you press the Pause button. Displayed in Auto Sequence mode where all channels are switched at the specific time interval. This icon is displayed if a user with restricted access to the Record button tries to make manual recording. Only the user with the applicable permission can release (stop) the recording. Displayed if the HDD is full and the DVR has an insufficient space to record. Displayed if no HDD is installed or the existing HDD should be replaced. Displayed if the HDD needs a technical examination. This will be displayed if the backup operation is in process. Displayed if a new firmware is found from the network. Video Input Status Displayed if no input is entered in the condition that the camera is set to <ON>. Nothing will be displayed on the screen if the camera is set to <OFF>. Camera Name/ Channel Displays the camera name and the changed channel, if any. Displays the resolution of the recording screen. (Page 47) Camera Operation Displays AUDIO ON/MUTE. Not displayed in video mode if deactivated. Displayed if a motion detected in the condition that the motion detection is set to <ON>. Displays the current record mode from Record/Event/Schedule. English _21

22 live Error Information If the internal HDD is not connected, the NO HDD ( ) message will appear; if there occurs a problem, you will see the HDD FAIL ( ) message in the top left corner. In this case, make sure you contact the service center for assistance as this may cause a failure of recording, playback or backup. M If you see the No HDD, HDD FAIL icons on the screen, contact the service center for more details. Live Screen Menu In addition to the buttons the remote control, you can access a desired menu by right-clicking the mouse any area in live mode. The context sensitive menu that appears by right-clicking the screen may differ, depending on the login/ logout, screen split mode and DVR operation mode. M Menu items of Search, Record, Backup, Shutdown can be deactivated, depending on the user permission. Scene Mode :10:25 Spot Out Audio Off Freeze Stop Alarm Record Play Search Backup Main Menu Shutdown Hide Launcher Logout :10:25Scene Mode Spot Out Zoom In Audio Freeze Stop Alarm Record Play Search Backup Main Menu Shutdown Hide Launcher Logout < Split Mode Menu > < Single Mode Menu > Split Mode Menu The context sensitive menu in split mode differs, depending on the login/logout status Scene Mode Spot Out Audio Off Freeze Stop Alarm Record Play Search Backup Main Menu Shutdown Hide Launcher Logout :10:25 22_ live

23 Menu Description Scene Mode Refer to Live Mode. (Page 25) b Spot Out Refer to Spot Out. (Page 27) c Audio On/Off Refer to Audio ON/OFF. (Page 28) Freeze Refer to Freeze. (Page 28) Stop Alarm Stops the alarm output and the event monitoring. Refer to Event Monitoring. (Page 28) Record/Stop Starts/stops the standard recording. Play Refer to Search & Play > Play. (Page 63) Search Refer to Search & Play > Search. (Page 60) Backup Refer to Using the DVR > Setting the Backup. (Page 52) Main Menu Accesses the main menu. Refer to the Using the DVR section. (Page 30) Shutdown Turns down the DVR. Show/Hide Launcher Shows or hides the launcher. Refer to View the Launcher Menu. (Page 24) m Login/Logout You can log in or out. LIVE Single Mode Menu The single mode menu is available only in Single Mode. The context sensitive menu for the One Channel mode, in Split mode is different from that of the Single mode :10:25 Full Screen Spot Out Zoom In Audio Freeze Stop Alarm Record Play Shutdown Hide Launcher Logout Menu Full Screen Description Select and click a desired channel in Split mode to switch to the full screen of the selected channel. b Zoom In Enlarges the selected image. (Page 27) English _23

24 live View the Launcher Menu The Launcher menu appears on the bottom of the live screen. 1. In Live mode, right-click to display the context menu and select <Show Launcher> :10:25 2. Move the cursor to the bottom and click a desired item in the Launcher menu. M If no input is entered for 10 seconds, the menu will disappear. The Launcher menu can be accessed only by using the mouse :10: :10: :10:25 Alarm Freeze Menu Date/Time Description Displays the current time and date. The indication of AM/PM is displayed if you set 12 hours for the time format in System > Date/Time/Language > Time. (Page 30) b Screen Mode Press this button to switch the screen mode in sequence. c Menu Expansion Button Click to display the hidden menu to the right. Audio Turns ON/MUTE the sound of the selected channel. Zoom Enlarges the selected area. This is available only in Single Live mode. Alarm Stops the alarm if it's activated. Freeze Freezes the Live screen temporarily. Play Enters Play mode if a file to play exist, and if not, enters Search mode. Record Start/End recording the Live screen. 24_ live

25 LIVE MODE Displays 4 live video images in 3 different modes. Switching the screen mode To switch the split mode, select a screen mode in the launcher menu, or right-click to select a screen mode in the context menu. Press the [MODE] button on the remote control to switch the mode in the sequence of the launcher menu items. CH1 CH2 CH3 CH4 CH1 4-split mode PIP Auto Sequence CH2 CH1 LIVE Switching the screen automatically You can display 4 live single screens in sequence. CH1 4 CH1 CH1 CH1 Single mode 1 M In Single mode, If you have set <SEQ-Dwell Time> in Setting the Device > Camera, Auto Sequence will be conducted at the set interval. (Page 40) English _25

26 live Channel Setting You can display the channel in a desired area of a split screen. 1. Click a camera name to display a channel list where you can select a different channel. 2. Select a desired channel and click it. The current channel will be switched to the selected one. Use the cursor to select a channel to move, and drag and drop it to a desired channel; this can also change the channel position. Ex : if switching CH 1 to CH 4 CH1 CH2 CH4 CH2 CH3 CH4 CH3 CH1 Switching to Single Mode When in split mode, select and double-click a desired channel to switch to its Single mode. Press the number corresponding to a desired channel the remote control to switch to its Single mode. Refer to Remote Control > Using the numeric buttons. (Page 12) Ex : If double-clicking CH 3 or pressing the number 3 on the remote control. CH1 CH2 CH3 CH4 CH3 26_ live

27 SPOT OUT The Spot Out monitoring is independent of the Live mode, which monitors a specific channel through the Spot Out port. Selecting a Spot Out mode 1. In Live mode, right-click any area on the screen. The Live menu appears. 2. Click Spot Out. Supports the Spot output in Single screen with Auto Sequence mode. The Spot output is supported only for a designated channel. For the Spot Out port of a model, refer to Part Names and Functions (Rear). (Page 11) Scene Mode Spot Out Audio Off Freeze Stop Alarm Record Play Search Backup Main Menu Shutdown Hide Launcher Logout :10:25 Auto Sequence CH1 CH2 CH3 CH4 LIVE < Multichannel l Live Menu > ZOOM This is available only in Single Live mode. In Single mode, select a desired area and use the Zoom function to enlarge it twice. 1. Select <Zoom In> in the right-click menu. Press the [ZOOM] button on the remote control, or simply click < > in the launcher menu. The zoom box appears. 2. Use the direction keys, or drag and drop to specify an area to enlarge. 3. Press the [ENTER] button, or double-click the selected area to enlarge it twice. In the enlarged image, use the direction buttons ( ) on the remote controlto move the enlarged area. 4. Press the [ZOOM] button on the remote control, or simply click < > in the launcher menu to release the zoom :10:25 English _27

28 live AUDIO ON/OFF You can turn the sound on/off the CH1 in Live mode. AUDIO ON/OFF in Single mode Click the audio icon ( M ) on the screen, or press the [AUDIO] button on the remote control to turn it on/off. Only the channel where <AUDIO> is set to <ON> in Device > Camera displays the audio icon ( that you can use to turn the sound on/off. ) in Live mode FREEZE This is available only in Live mode, this pauses playing the Live image temporarily. 1. Press the [FREEZE] button the remote control, or click < Freeze > in the launcher menu. The playback of the image is stopped temporarily. 2. Press the [FREEZE] button again, or click < Freeze >. This will release the freeze. EVENT MONITORING This will display the channel in sync with a specific event (Motion/Video Loss) if it occurs. In Monitor > Event Display, set the event monitoring to ON/OFF and specify the event display time. (Page 44) If multiple events occur simultaneously, the screen will switch to a split mode. - 2~4 events : 4-split mode If the second event occurs within the set time of <Event Display>, the first event will last until the second one is terminated. (Page 44) Ex : If you set <Event Display> to 5 seconds, and only one event occurs in CH 1. Event occurrence 5 seconds Stop alarm CH1 28_ live

29 Ex : If you set <Event Display> to 5 seconds, and the second event occurs in CH 2 within the set time after the first event occurred in CH 1. Event occurrence 4 seconds 9 seconds CH1 CH1 CH2 Stop alarm LIVE M Press the [ALARM] button to reset the alarm settings and to release the event mode. If an alarm activates in the condition you have set the event record, and pre/post alarm times, the event record will be performed. English _29

30 using the DVR You can setup the system properties, devices, and options for recording, event, backup and network. SYSTEM SETUP You can setup Date/Time/Language, Permission, System Properties and Log. Date/Time/Language You can check and setup the current Date/Time and time related properties, as well as the language used for the interface on the screen. Setting the Date/Time/Language Set the Date/Time/Language Using the mouse may help make setup easier. 1. Press the [MENU] button on the remote control. If not logged in, it prompts with login window. Refer to Login. (Page 20) :10: :10:25 2. Use the left/right buttons ( ) to select the <System>. System property setup menu is selected. Logout Return 3. Use the up/down buttons ( ) to select <Date/Time/ Language> and press the [ENTER] button. 4. Select <Date/Time/Language>. A dialog to setup Date, Time and Language. 5. Use direction buttons ( ) to select an item to set and make your changes. System Date/Time/Language Permission Management System Management Log Information Date : Sets the date that will appear on the screen. Date/Time/Language You can select the date format. Date/Time/Language Holiday Time : Sets the time and its format that will appear on the screen. Select either one from <24 Hours, 12 Hours (AM/PM)>. Time Zone GMT Time Sync. Setup Time Zone : Sets the time zone of your area based on the Greenwich Mean Time (GMT). Language English GMT (Greenwich Mean Time) is standard World Time and the basis of world time zone. OK Cancel Time Sync. : You can set the DVR s current time synchronized to a selected <Time Server> regularly if you select to use <Time Server>. In this case, <Date/Time/Language> setup does not allow time adjustment. Date YYYY-MM-DD Time 08:14:24 24 Hours DST Dec First (Sun) 0 Dec First (Sun) 0 30_ using the DVR

31 - Time Server : Enter an IP or URL address of the time Date/Time/Language server. Date/Time/Language Holiday - Last Sync Time : Displays the most recent Date Time Synchronization Setup YYYY-MM-DD synchronization time from the selected time server. Synchronization Use - Activate as Server : Set to <Use> to allow the DVR to act Time 08:14:24 24 Hours Time Server Time Zone GMT+08:00 as a Time Server for other DVRs. Last Sync Time Fail Time Sync. Setup Not Used Activate as Server Use DST Dec First (Sun) 0H Dec First (Sun) 0H DST : Set up Daylight Saving Time with its period to make OK Cancel the time earlier than the GMT of its time zone by 1 hour Language English during the set period. OK Cancel Language : Select your language. Sets the language for the interface. English, French, German, Spanish, Italian, Chinese, Russian, Korean, Polish, Japanese, Dutch, Portuguese, Turkish, Czech, Danish, Swedish, Thai, Romanian, Serbian, Croatian, Hungarian and Greek are available. 6. When the Date/Time/Language setup is done, press <OK>. M You can also use numeric buttons on the remote control to enter values for Date, Time and other numeric fields. USING THE DVR Setting Holiday You can set specific dates to Holidays according to your preferences. Holidays are applied to <Recording Schedule> and <Alarm Schedule> too. Using the mouse may help make setup easier. 1. Use the up/down buttons ( ) in <Date/Time/Language> window to select <Date/Time/Language>, and press the [ENTER] button. 2. Select <Holiday>. Date/Time/Language A calendar for Holiday setup appears. Date/Time/Language Holiday 3. Use the left/right < > buttons to select year or month, 2012 Jan and press the [ENTER] button. Sun Mon Tue Wed Thu Fri Sat OK Cancel 4. Use direction buttons ( ) to select a desired date, and press the [ENTER] button. You will see the Setting Holiday screen. Ex : Select January 9th and check on <1/9> only to make every January 9th a holiday. Check both on <1/9> and <Jan 2nd Mon> to make every January 9th and 2nd Monday of January holidays. 5. When the Holiday setup is done, press <OK>. Date/Time/Language Date/Time/Language Holiday 2012 Jan Setting Sun Holiday Mon Tue Wed Thu Fri Sat / Jan 2nd Mon OK 25 Cancel OK Cancel Using the Calendar Using the mouse may help make setup easier. Select year and month. Select the left/right < > key on the left/right side of year/month and press [ENTER] button to adjust by 1 year/month. Use direction buttons to select a date and press [ENTER] button. A date with recorded data to be searched will appear in yellow in the System Log, Event Log, Time Search and Event Search. English _31

32 using the DVR Permission Management You can set permissions of each user over the DVR's specific function and settings. Setting the Administrator You can set and change Administrator s ID and password. The administrator can use and set all menu items and functions. Using the mouse may help make setup easier. 1. Use the up/down buttons ( ) in <System> window to move to <Permission Management>, and press [ENTER] button. 2. Select <Admin>. A dialog for Admin ID and Password input appears. 3. Use direction buttons ( ) to move to a desired item, and set the ID and password. M By default, initial ID and password are set to admin, and OK Cancel The default password can be exposed to a hacking thread so it is recommended dto change the password after installing the product. Note that the security and other related issues caused by the unchanged password shall be responsible for the user. 4. When the administrator setup is done, press <OK>. Permission Management Admin Group ID admin New Password ************ Confirm P/W ************ User Setup Using Virtual Keyboard For alphanumeric inputs, the virtual keyboard window appears. Use direction buttons ( ) to move to a desired character, and press the [ENTER] button. In the upper text input box of the virtual keyboard, there displays a list of candidate words containing the selected character. Select a word from the list, or use the keyboard to enter the whole word. ` = q w e r t y u i o p [ ] \ Del a s d f g h j k l ; Caps Lock z x c v b n m,. / Shift Space Ctrl If there are many of candidate words, use <, > buttons to move between them forward and backward. Select <OK>. Entered word is applied. For upper case letters, use <Caps Lock> button. For special characters, use <Shift> button. Using the virtual keyboard is the same to a normal keyboard use in your region. You can enter the ID with case-insensitive alphanumeric characters only. For the password, use alphabets and special characters excluding < \ > and < >. You can use number buttons on the remote control. OK Cancel 32_ using the DVR

33 Setting the Group You can create user groups and setup permissions for those user groups. You can register a user for each group in <User>. Using the mouse may help make setup easier. 1. Use the up/down buttons ( ) in <System> window to Permission Management move to <Permission Management>, and press Admin Group User Setup [ENTER] button. Group Add Delete Rename Group Authority 2. Select <Group>. Live View Setup Search Setup A window for <Add>, <Delete>, <Rename>, and Backup Setup <Group Authority> setup appears. 3. Use direction buttons ( ) to move to a desired item, and set the value. OK Cancel Add, Delete, Rename : You can add, delete, rename a group or modify the permissions given to the group. The virtual keyboard appears when <Add> or <Rename> was selected. - Add : When you first run the DVR with the admin account, only the admin account exists. Add has already been deactivated. Select to display the virtual keyboard. Enter a group name. You can add up to 10 groups. - Delete : Deletes a user group that is already registered. Selecting Delete will delete all user accounts belonging to that group. - Rename : Renames a group that is already registered. Select <Rename> to display the virtual keyboard. For entering a group name, refer to Using Virtual Keyboard. (Page 32) Group Authority : Sets permissions to access menu items of each group. Users of a group can access checked functions. 4. When the group setup is done, press <OK>. USING THE DVR To set the group authority You can set the permissions of the group users to access the menu according to the channel. 1. Select a menu to which the group permission is assigned. Permission Management The menu where the group permission is assigned will be Admin Group User displayed in the Live menu when a group user logs in. Live View : You can set the permission to access the Live screen according to the channel. Search : You can set the permission to access the Search menu according to the channel. Backup : You can set the permission to access the Backup menu according to the channel. 2. Select <OK>. Select and assign a group user so that the user can access the specified menu. Group ABC Add Delete Rename Group Authority Channel Setup Live View Setup All Search Setup Backup Setup OK OK Cancel Cancel Setup English _33

34 using the DVR To restrict the user permissions If the admin restricts all permissions of an added group, the users belonging to that group can access only the default minimum menus and can change the user s own password only. 1. Start the DVR. If all permissions are restricted, only the Login dialog should appear. 2. Log in with a registered user ID. Login ID Password abc OK Cancel 3. Right-click any area on the screen. If all permissions are restricted, only the accessible context menus should appear :10:25 Scene Mode Audio Off Freeze Stop Alarm User Menu Hide Launcher Logout :10:25 To change the user password If you log in with a user account that is restricted to access the menu, you can change your own password only. 1. Log in with your account. Permission Management User 2. Select <User Menu>. The Permission Management setup screen appears. ID abc New Password ************ 3. Select <Permission Management>. Confirm P/W ************ The Password setup dialog appears. 4. Enter a new password. 5. Select <OK>. You change to the password will be applied. OK Cancel 34_ using the DVR

35 Setting the User Users can be added only if a group was created in <Group> menu. Using the mouse may help make setup easier. 1. Use the up/down buttons ( ) in <System> window to move to <Permission Management>, and press [ENTER] button. 2. Select <User>. A window for Add User appears. 3. Use direction buttons ( ) to select <Add> from the window. A window for Add User appears. You can configure the Network Viewer settings including name, ID, viewer, Select Group and password. Result of the user setup appears in the <User> window. To change the user property, use Edit User. The Edit User window appears when you select a desired item to be changed in the <User> window. Viewer : If you select <Use>, you will be given access to the Web Viewer and Network Viewer. Refer to Connecting Web Viewer. (Page 66) For more information about use of Network Viewer, refer to the Network Viewer's user guide. 4. When the user setup is done, press <OK>. Permission Management Admin Group All Group Group User Group Name ID Viewer Delete OK Permission Management Admin Group Add All Group User Group Cancel User Setup Previous/Next Page Group Name Name ID Viewer Delete ID Viewer Not Used Select Group ABC Password Confirm P/W OK OK Cancel Cancel Setup Previous/Next Page Add Add USING THE DVR Setting Permissions You can set restricted access for all general users. Items with restrictions will require logging in for use. Using the mouse may help make setup easier. 1. Use the up/down buttons ( ) in <System> window to Permission Management move to <Permission Management>, and press Admin Group User Setup [ENTER] button. Restricted Access Live View Backup All 2. Select <Setup>. Restriction on Network Access All Network Web Viewer The Restricted Access, Restriction on Network Access, Auto Log out OFF Auto Log out, Manual Input of ID setup screen appear. Manual Input of ID ON 3. Use direction buttons ( ) to move to a desired item, and set the value. OK Cancel Restricted Access : All menu items allowed for a user can be set with restricted access. - Checked ( ) : Restricted - Not checked ( ) : Accessible If it is not checked ( ) in <Restricted Access>, any user can access the item no matter what the <Group Authority> setting. If it is checked ( ) in <Restricted Access>, a user can access the item only if the user has permission in <Group Authority> setting. Restriction on Network Access : Restricts remote access from a <Restricted Access> network. - All Network : Restricts all access instances via Network Viewer and Web Viewer. - Web Viewer : Restricts access via the Web Viewer. Auto Log out : A user will be automatically logged out if there is no operation on DVR for over set period of time. English _35

36 using the DVR Manual Input of ID : Prompts you to enter the user ID manually for the login process. - Checked ( ) : Encloses the registered user IDs with the [ ] symbols. Use the virtual keyboard to enter the user ID. 4. When the permission setup is done, press <OK>. Login ID ***** Password OK Cancel System Management You can check the system version, update to a newer version, as well as data backup and initialization. Checking the System Information You can check the current system version, broadcasting system, MAC address. You can update the system. Using the mouse may help make setup easier. 1. Use the up/down buttons ( ) in <System> window to move to <System Management>, and press [ENTER] button. 2. Check the Version, Broadcast Format, and MAC Address. System Information : Shows the current system s information. The values can not be changed by a user. S/W Upgrade : Updates the DVR s software. System Management System Information System Information Software Version Broadcast Format MAC Address S/W Upgrade Device Version v1.0xh_yymmddhhmmss NTSC 00:00:F0:54:FF:FF No Device No S/W Data Settings Previous Upgrade Ex : If you connect to a storage device that has upgradable software installed, and return to the <System Management> menu, the current software version will be displayed. System Management System Information Settings System Information Software Version v1.0xh_yymmddhhmmss Broadcast Format MAC Address NTSC 00:00:F0:54:FF:FF S/W Upgrade Device Version USB2FlashStorage v1.0xh_yymmddhhmmss Upgrade Previous 36_ using the DVR

37 Updating the Software 1. Connect a device storing the software to be updated. (It may take about 10 seconds to recognize the device.) Upgradeable devices include USB memory and network device. To update the network, the current DVR should have been connected to the network. Upgrade via the proxy server may not be enabled due to the restricted access. System Management System Information Settings System Information Software Version v1.0xh_yymmddhhmmss Broadcast System Format Upgrade NTSC MAC Address Current Version 00:00:F0:54:FF:FF v1.0xh_yymmddhhmmss New Version v1.0xh_yymmddhhmmss S/W Upgrade Do you want to upgrade? Device USB2FlashStorage Upgrade OK Cancel Version V1.08_ Select <System Management> from <System> window. Previous 3. Select <System Information>. 4. When the recognized device appears, select <Upgrade>. The <Upgrade> button will be activated only if the current <Software Version> of the <System Information> is same to or older than that of <S/W Upgrade>. 5. Press <OK> in the System Upgrade window. While updating, it shows the progress. Updating progresses with 3 steps as shown in the figure. System Management System Information Settings System Information Software Version v1.0xh_yymmddhhmmss Broadcast Format S/W Upgrade NTSC MAC Address 00:00:F0:54:FF:FF Software upgrading... S/W Upgrade Device USB2FlashStorage Upgrade USING THE DVR Version V1.08_ Previous System Management System Information Settings System Information Software Version v1.0xh_yymmddhhmmss Broadcast Format S/W Upgrade NTSC MAC Address 00:00:F0:54:FF:FF Software upgrading... Software upgrading... S/W Upgrade Do not turn off during the upgrade. Device USB2FlashStorage Upgrade Version V1.08_ Previous 6. When the updating is done, it automatically restarts. Do not turn the power off until it finishes restarting. M If Upgrade Failed appears, retry from the step 4. When you experience continued failure, consult the service center for assistance. English _37

38 using the DVR Settings You can copy and import the DVR settings by using a storage media. Using the mouse may help make setup easier. 1. Use the up/down buttons ( ) in <System> window to move to <System Management>, and press [ENTER] button. 2. Select <Settings>. A window of storage device and load factory default appears. 3. Use direction buttons ( ) to move to a desired item, and export or import settings data to a storage device. System Management System Information Storage Device DVR USB USB DVR Load Factory Default Storage Device : Shows the connected storage device. Export : Exports DVR settings to the connected storage device. Import : Imports DVR settings from the storage device and applies to the DVR. If <Include Network Settings> is checked, the network settings will be imported too. No data Settings Include Network Settings Default 0 MB (Remained Capacity) Previous Export Import Load Factory Default : If <Default> is selected, a confirmation dialog for Load Factory Default prompts. Press <OK> to initialize the system to the factory default. 4. To move to the previous menu, press <Previous>. System Management System Information Settings Storage Device 0 MB (Remained Capacity) DVR USB Load Factory Default Export USB DVR No data Import Sure to Default Include Setting? Network Settings Load Factory Default OK Default Cancel Previous Log Information You can browse logs on the system and events. System Log System Log shows log and timestamp on every system start up, system shutdown, and changes on system settings. Using the mouse may help make setup easier. 1. Use the up/down buttons ( ) in <System> window to move to <Log Information>, and press [ENTER] button. 2. Select <System Log>. Refer to Using the Calendar. (Page 31) Click on the calendar < > to display the calendar window. Log Information System Log Event Log Backup Log Search Day Search First Page Last Page Type View all No. Log List Date/Time Type : When there are too many logs, you can display logs of the desired format by selecting the type. 3. Use direction buttons ( ) to move to a desired item, and press <Search>. Previous Previous/Next Page 38_ using the DVR