Glow P18i LED Par USER MANUAL 18*8W,RGBW 4-IN-1 QUAD- COLOR

Transcription

1 Glow P18i LED Par USER MANUAL 18*8W,RGBW 4-IN-1 QUAD- COLOR

2 TABLE OF CONTENTS 1. Summary 3 Product Introduction 3 Content List 3 2. Safety Information 3 Safety notes 3 Safety instructions 4 3. Product diagram 4 4. Features 5 5. DMX Control 5 DMX Channel(3CH) 5 DMX Channel(4CH) 6 DMX Channel(5CH) 6 DMX Channel(8CH) 7 6. Display Operation 8 7. Menu Instructions 8 Operating instructions Operating Control Instructions 11 Master/Slave XLR cable connecting 12 XRL cable Wiring diagram Trouble Shooting Technical Specifications 15 2

3 1. SUMMARY Thank you for purchasing our Glow P18i LED Par. Please read these instructions carefully before operating the system to avoid any possible damage or misuse. PRODUCT INTRODUCTION The Glow P18i LED Par light is encased in an aluminum shell, and displays a long can, short can and colour filter. It s high power 4-in-1 LEDs (made up of R, G, B, W LEDs) have a long life expectancy, low power consumption, good colour mixing effect ability and high brightness, and can each be independently dimmed and controlled. The light also includes built in programs such as dimming, strobe, gradual change and fading. An international standard DMX 512 signal is recommended for best results. CONTENT LIST o GLOW P18I LED PAR light (x1) o DMX signal cable (x1) (sold separately) o The User Manual (x1) 2. SAFETY INFORMATION SAFETY NOTES Seek advice from a professional prior to authoring any repairs Always ensure the system is disconnected from the power source before assembling, deconstructing and moving Avoid direct eye exposure when in use 3

4 SAFETY INSTRUCTIONS Ensure the power supply voltage corresponds with the required voltage for the lights, and is within the range of the requested technical restrictions. Before installing, check the lights fasteners and mechanical structures are in good condition and there is no apparent damage. This light is designed for indoor and outdoor use, however the working temperature must be kept below 50 degrees. The fixtures can be mounted in any position, provided there is adequate room for ventilation. Make sure there are no inflammable and explosive items within 0.5 meters of the fixture. The yellow/green cables are for earthling safety. These should not flicker when fixture is in use. 3. PRODUCT DIAGRAM 4

5 4. FEATURES o High quality LED: low power consumption, good brightness, stable capability and long life span o Each coloured LED equipped with 256 dimming. The RGB can make over 16.7 million different colour combinations. o Dim: 0%-100% (Strobe, gradual change, jumping change etc.) o DMX512 Controller, 4 button set DMX ID address with led display o Auto run /sound activated/master slave/interconnected multi-machine control o Uses a switching power supply to protect the LED o Lens degree: 25º or 45º options o 3, 4, 5, 8CH DMX control channel options o Body color: black or white DMX CHANNEL( 3CH) 5. DMX CONTROL Channel DMX Value Control Function Remarks 1CH RGB color mixing Hue 2CH W Dimming Color Saturation 0-100% 3CH General dimming 0-100% Purity Note: Chromaticity is the visible light, such as red, green, yellow, cyan etc. Color saturation refers to the proportion of color chromaticity possession (100% saturation means the color has reached its purest state). Purity value refers to the brightness, when purity reaches 100% and the color is the brightest. 5

6 DMX CHANNEL( 4CH) Channel DMX Value Control Function Remarks 1CH R 0-100% 2CH G 0-100% 3CH B 0-100% 4CH W 0-100% DMX CHANNEL( 5CH) Channel DMX Value Control Function Remarks 1CH General dimming 2CH R 0-100% 3CH G 0-100% 4CH B 0-100% 5CH W 0-100% 6

7 DMX CHANNEL( 8CH) Channel DMX Value Control Function Remarks 1CH General dimming 2CH Red dimming 0-100% 3CH Green dimming 0-100% 4CH Blue dimming 0-100% 5CH White dimming 0-100% 6CH 0-14 Dimming When 7CH>31,this Strobe Speed function is invalid Invalid From dark to bright Must use CH1, 2, 3, 4, From bright to dark 5CH, otherwise the light From dark-brightdark will not work. The speed 7CH will start adjusting from the 8CH RGB Gradient The speed will start adjusting from the 8CH Dark-bright-dark auto run colors jumping change Multi-colors jumping change 8CH Speed Adjustment (7CH) 7

8 6. DISPLAY OPERATION DMX IN DMX OUT DMX IN/OUT MENU: Access the menu UP: Increase menu selection DOWN: Decrease menu selection ENTER: Confirm the current menu option MENU UP DOWN ENTER LED Display 4 buttons 7. MENU INSTRUCTIONS Addr A001- A512 DMX Mode SLAV SL.AV Slave receiving mode CHNd DMX receiving channel choosing SP- - SP- SP15 Built- in program speed Pr- - Pr00- Pr15 Built- in program MENU ASC AS00- AS15 Color Jumping 8

9 FADE FA00- FA15 Gradual Changing mode FLAS FL00- FL15 White strobe mode RL r000- r255 Red dimming gl g000- g255 Green dimming DL b000- b255 White dimming UL u000- u255 White dimming 9

10 OPERATING INSTRUCTIONS: MENU is used to access the menu or return to the previous menu option. It cannot be used to select and store the current menu option. Press UP / DOWN to choose a desired menu item. The operation details are as followed: Addr :DMX mode(a001-a512) SLAV : Slave receiving mode CHNd : DMX receiving channel selection(3, 4, 5, 8) SP - - :Modify built-in program speed (SP00-SP15,SP00 is the fastest) Pr- - :Built-in program(pr00-pr15 there are 16 kinds of programs) ASC- :Multi-colour jumping mode(as00-as15 : speed adjustment) FadE :Gradual change mode(fa00-fa15: modify speed) FLAS :White strobe speed(fl00-fl15: modify speed) rl- - : Adjust red brightness mode(r000-r255, r255 is the brightest) gl- - :Adjust green brightness mode(g000- g255, g255 is the brightest) bl- - :Adjust blue brightness mode(b000- b255, b255 is the brightest) UL- - :Adjust white brightness mode(u000-u255, U255 is the brightest) Press ENTER to access further menu settings. This process will be saved automatically; so that when next activate the light you will be able to continue with the previous session. For example, if you want to choose DMX mode (A001), the operation details are as followed: Press MENU to return to the initial setting Press UP / DOWN until Addr Press ENTER to select. The display will flash. Press UP / DOWN to change the address code to select A001 Press ENTER to select and store the current menu options. DMX mode will be stored automatically and the screen will stop flashing. To choose the DMX channel:chnd mode Press MENU to return to the initial setting Press UP/DOWN until CHNd Press ENTER to select. The display will flash Press UP/DOWN to modify DMX receiving channel,3ch, 4CH, 5CH, 8CH 10

11 Press ENTER. If you hold ENTER for longer than 3 seconds, the DMX channel will be saved and you will return to DMX receiving mode(a001). If you press ENTER (with for less than 3 seconds) or not press ENTER at all, the DMX channel will be automatically selected and saved and you will return to DMX receiving mode(a001). Details of built-in program(pr- -): Press MENU to return to the initial setting Press UP/DOWN until pr- - Press ENTER to select. The display will flash Press UP/DOWN to modify the built-in program until Pr00 Press ENTER to select and store the current menu option. DMX mode will be saved automatically and the screen will stop flashing. Note: Pr14--- Pr30 can modify the content of SP-- - and correct the speed of the jumping change (Where SP00 is the fastest and SP15 is the slowest) Pr00-Pr13:RGBW single color or multi-color mixing Pr14-Pr27:Pr00 - Pr13 corresponding with increasing strobe function Pr28:4 colors jumping change 8. OPERATING CONTROL INSTRUCTIONS MASTER/SLAVE Master setting: The master should be one of following modes: built-in mode, color jumping mode, fade mode, white strobe mode or manual dimming mode. This sends out a synchronized signal to the slave. To avoid the master signal and DMX512 signal from interfering with each other, the DMX512 signal must be cut off. When the signal cables are longer than 60 meters, a DMX signal amplifier is necessary. Slave setting: Settings must be in the SLAV mode and the address code should be A001 to assure the master s signals are received correctly. Only one light can be set as a Master and the remaining are slaves. 11

12 XRL CABLE 9. XLR CABLE CONNECTING The standard connection of the XRL should have one end connecting to the male plug, and the other connecting to the female. As below: pin 1 - ground, pin 2 - negative signal, pin 3 - positive signal Note: In order to avoid failures and interference with signal transmission, connect a resistance 120 (1/4W)at the end of the DMX connection as shown below: The conversion between 3 pin and 5 pin XLR. If the output cable of the DMX512 controller is a 5PIN, a 5PIN to 3PIN cable is necessary. 12

13 10. WIRING DIAGRAM 13

14 11. TROUBLE SHOOTING Problem The light won t turn on Suggestions Check the power plug is working normally Check if the light switch is off or on Check if the power supply is working normally Check if the DMX cable is connect to the light properly The DMX is not Check if the DMX512 controller is working normally. controlling the light Check if the DMX cable is damaged. Check if the light is in DMX mode (Addr:001). Check if the power input of the IC board is working. The display is not Check if the cable connected to the display is secure. working Change the main board to ensure that it is working properly. Change the display. Check if the power input of the IC board is working. The LED is not Check if the cable connected to the display is secure. light Change the main board to ensure that it is working properly. Check if the LEDs are secure, as the LED is connected by LEDs in Some of the LEDs series. are not light Use the multimeter (diode) to check if the LED is bright or not. If not, the LED will need replacing. Check constant current IC is working properly (compared with the normal IC). Single color LEDs Check if the voltage of the input end of corresponding color is are always working. bright/not bright Change the IC control board. Note: Seek advice from a professional prior to authoring any repairs 14

15 12. TECHNICAL SPECIFICATIONS Input voltage: AC 100V- 264V/47-63HZ Output voltage: DC24V Consume: 144W Lamp Type: High Power LED(8W) Lamp Spec: 4- in- 1 8W(18PCS) Constant current driver:5 00MA Refresh rate:>400hz Life span: 50000~100000hours Control Signal:DMX512, sound activated, auto run Control mode:stand alone/ sound activated Channel:3,4,5,8CH Color effect:rgbw mixing Function Effect: dimmer, strobe, gradual change, sound activated Beam Angle: 15, 25,45 Cooling mode: Natural Convection Anti- electricity intension:1.5kv Insulation Resistance:>2MΩ Size:30*22*23cm Net Weight:2.5KG 15