Installation instruction Rear view camera

Transcription

1 Version 1.03 ( ) Installation instruction Rear view camera Article no.: Audi A6 4G Audi A7 4G Kufatec GmbH & Co. KG Dahlienstr Bad Segeberg

2 Contents General advice...1 Safety instruction...2 References of legal regulations for operation...2 Rear view camera...3 Scope of delivery...3 Installation instructions...4 Video wires connection...8 CAN wires connection...8 Coding...10 General advice While developing this product, your personal safety combined with the best operating service, modern design and an up-to-date production technique was especially taken into account. Unfortunately, despite the utmost care injuries and/or damages might occur due to improper installation and/or use. Therefore please read with great care and completely this operating manual and store it appropriately! For your safety all our products pass through a 100% control check. We reserve the right to carry out technical changes which serve the improvement at any time. According to each article and purpose, it is sometimes necessary to check each country s legal regulations before installing and starting the unit. In case of guarantee claims, the device has to be sent back to the seller in the original packaging with the attached bill of purchase and detailed defect s description. Please pay attention to the manufacturer s return requirements (RMA). The legal warranty directions are valid. The warranty claims as well as the operating permissions become invalid due to: a) unauthorized changes to the device or accessories which have not been approved or carried out by the manufacturer or its partners b) opening the device s frame c) self-made repairs on the device d) improper use / operation e) brute force to the device (drop, willful damage, accident etc.) During installation, please pay attention to all safety relevant and legal directions. The device has only to be installed by trained personnel or similarly qualified people. 1

3 Safety instruction The installation can be executed only by trained qualified personnel. Before the installation disconnect the power supply. Therefore cut off the battery from the vehicle electric system, follow the manufacturer s specification. Never use bolts, screws and other fastening elements from car s safety devices or steering wheel, brakes because it may influence your driving safety and cause accidents. Connect the device only to a 12V vehicle voltage with chassis ground to the car body. This unit cannot be used in large trucks or other vehicles which use a DC 24 V battery wiring system voltage. Avoid to install the device in places where it could hinder the safe driving or functional efficiency of the other units installed in the vehicle. This unit is only for the use with the following vehicles and model line; Only connections described within this instruction manual are allowed or required to use for installation. For damage impact caused by faulty installation, unsuitable connections or assembling in inappropriate vehicle types or models Kufatec GmbH &Co.KG assumes no liability. We advise you that these units process data out of the MOST protocol from the vehicle. During the assembly of this unit we as supplier have access to a specific model and we as producer don t know the overall system you work with. Especially in case of changes within the same model line and the same model year we don t guarantee the usability of our products. In case of the usability of our products with the manufacturer s changes Kufatec GmbH assumes no liability. Kufatec GmbH assumes no liability that the assembly of the unit described in this manual is approved according the warranty regulations of the single car manufacturers. Please check your manufacturer s conditions and warranty before you begin the installation. Kufatec GmbH reserves the right to change the device specification without further notice. Errors and changes excepted. References of legal regulations for operation Use this unit in the intended domain only. If you use the unit in a foreign domain, if the unit is not installed properly, or if the unit will be reconstructed the operating permit and warranty will expire. 2

4 Rear view camera Wide angle display of the rear area in MMI via a camera integrated in the handle bar Considerably simplified orientation through the support lines and fields displayed in the video screen that change appropriately to the steering angle There are 2-park modes available lengthwise and transversal All the standard functions remain fully intact Uncomplicated assembling, no cutting off the existing wires necessary Scope of delivery Cable set Control device Handle bar with integrated camera Scope of delivery (from modelyear 2012) - Cable set - Control device - Handle bar with integrated camera Scope of delivery Cable set 3

5 Installation instructions The following presentation shows the laying of the wires and the position of the single components as well Rear view camera 2 Rear view camera Control device 3 MMI drive 4 CAN breaking plug Fig.1 Audi A7 4G Take out the breakdown triangle (fig. 2) loosen the screws situated behind (fig. 3). Fig.2 Fig.3 Dismantle the lining of the trunk lid (fig. 4, 5). Fig.4 Fig.5 4

6 Remove the rear end cover mask this is only inserted (fig. 6). Loosen the necessary screws of the side lining (fig. 7) and the lashing eyes in the trunk as well. Fig.6 Fig.7 Fig.8 Carefully remove the left-hand side lining (fig. 8). NOTE: Disconnect the plug of the trunk illumination. Audi A6 4G Take out the breakdown triangle (fig. 9) actuate the locking of the holder situated behind and remove (fig. 10). Dismantle the trunk lid lining. Fig.9 Fig.10 Loosen the necessary screws / pins of the side lining (fig. 11) and the lashing eyes (fig. 12) in the trunk as well. Fig.11 Fig.12 Carefully remove the left-hand side lining. NOTE: Disconnect the plug of the trunk illumination. 5

7 The installation steps described below are valid for all vehicle versions. Unscrew the bolts of the handle bar inclusive the push button of the trunk lid opening. Assemble the rear view camera (fig. 13). Connect the 2-pin FAKRA plug of the camera with the delivered cable set (fig. 14). Fig.13 Fig.14 Lay the cable set alongside the existing vehicle wires toward the trunk (fig. 15). Connect the video wires (GRAY) coming from the camera to the RVC- control device (GRAY) (fig. 16). Connect the GREEN FAKRA plug and the main cable set to the RVC control device (fig. 16). Fig.15 Fig.16 Dismantle the holder slide in the RVC control device (fig. 17, 18). Fig.17 Fig.18 6

8 Laying of the wires in the front area of the vehicle (fig. 19). Lever the rear kicking plate out of its frame. Afterwards the kicking plate in the front area has to be removed (fig. 20). Fif.19 Fig.20 Loosen the necessary screws of the glove compartment (fig. 21, 22). Fig.21 Fig.22 Carefully lever the air conditioning control device (plastic wedge) fig. 23. Unscrew the bolt of the MMI 3G device (fig. 25). Take the MMI 3G device out of the center console and disconnect the original plug connections. Fig.23 Fig.24 Fig.25 7

9 Video wires connection MMI 3G device Fig.26 The connection of the Quadlock-plug takes place via two wires in total. T Transparent PIN 11 Black PIN 5 Abb. 18 CAN wires connection CAN breaking plug Push the pink locking to the right-side (fig. 28). Press the CAN breaking plug down and take out. Actuate the pink locking and remove the covering cap (fig. 29). Fig.27 Fig.28 Fig.29 8

10 Remove the pink safety locking (fig. 30). Fig.30 Actuate the locking and take out the casing of the CAN breaking plug (fig. 31). Pin the wires in the following cells: PIN 22 Low Fig.31 PIN 22 High NOTE: If the PINs are occupied, then the wires have to be integrated on the free PINs on the same cable link. The wire for the permanent positive has to be connected with the proper fuse carrier. Check before the installation which fuse carrier leads the permanent positive. Connect the ground wire with the ground point (fig. 33). Fig.32 Fig.33 9

11 Coding In order to carry out the coding of the vehicle please contact your local Audi dealer. Establish a connection with the diagnostics device - choose the vehicle self-diagnostics. Execute the coding stepby-step according to the following figures. Address 19 Self-diagnostics Address 19 Diagnostics interface for the data bus Coding Installation list Set the rear view camera on coded confirm the coding 10

12 Address 5F (FOR vehicles with Navigation Plus) Byte 07 - Bit 1 set on 1 xxxxxx1x Address 5F Information electronics Coding Master Select BIN Enter the coding value + confirm 11

13 Address 5F (FOR vehicles with Radio Plus, Navigation) Byte 06 - Bit 2 set on 1 xxxxx1xx Address 5F Information electronics Coding Master Codierung Byte Index Hex Bit-Muster xxxxx1xx C 0 Q HEX BIN Select BIN Enter the coding value + confirm 12

14 Address 6C In order to carry out the coding of the vehicle please contact your local Audi dealer. For the execution of vehicle coding choose the vehicle self diagnostics. Fahrzeugsystem auswählen 55 Leuchtweitenreguliereung 5C Spurassistent 6C Rückfahrkamera 17 Schalttafeleinsatz 46 Zentralmodul Komfortsystem 56 Radio 10 Einparkhilfe II 07 Anzeige-/Bedieneinheit 09 Elektrische Zentralelektrik Self-diagnostic Address 6C Unterstützte Funktionen Diagnosefunktion auswählen 6C Rückfahrkamera 001 Identifikation 004 Fehlerspeicherinhalt 008 Codierung 011 Messwerte 012 Anpassung 017 Sicherheit Coding Enter the coding value + confirm Coding value: (with towing hitch, with APS+) (only RVC) (with APS+, without towing hitch) (with towing hitch, without APS+) NOTE: In vehicles with dynamic steering box assembly set Bit 3 Example: xxx?xxx xxx1xxx 13

15 Address 10 (ONLY for vehicles with APS+) Addition in vehicles with factory-made APS+ function (optical park assist). Systemauswahl Wählen Sie ein System aus: Eigendiagnose Eigendiagnose Verbundsysteme LT2 Eigendiagnose Crafter Eigendiagnose Fahrzeugsystem auswählen 55 Leuchtweitenreguliereung 5C Spurassistent 16 Lenkradelektronik 17 Schalttafeleinsatz 46 Zentralmodul Komfortsystem 56 Radio 10 Einparkhilfe II 07 Anzeige-/Bedieneinheit 09 Elektrische Zentralelektrik Self-diagnostics Address 10 Park assist Unterstützte Funktionen Diagnosefunktion auswählen 001 Identifikation 004 Fehlerspeicherinhalt 008 Codierung 011 Messwerte 012 Anpassung 017 Sicherheit 6C Rückfahrkamera Codierung Codierung auswählen Binärcodierung Klartextcodierung Coding Master Plain text coding Fahrzeugsystem auswählen Codierung Parameter anpassen 10 Einparkhilfe 2 15 Airbag ja erreichbar i.o. 55 Leuchtweitenregelung ja erreichbar i.o. 5C Spurassistent ja erreichbar i.o. 16 Lenkradelektronik ja erreichbar i.o. 46 Zentralmodul Komfortsystem ja erreichbar i.o. 56 Radio ja erreichbar i.o. 10 Einparkhilfe 2 ja erreichbar i.o. Name Start-Stopp-Funktion, Codierungs. Spurhalteassistent mit Lenkunter. Anzeige OPS Kameratyp Wert Start-Stopp-Funktion Stg. Aktiv nicht aktiviert verbaut Kameratyp Nicht verbaut Rückfahrkamera Address 10 Park assist 2 Set the camera type not installed on rear view camera confirm 14

16 Finally an MMI reset has to be executed! Press the marked keys simultaneously (fig. 34). MENU + rotary knob + right above MMI system executes a new start. Fig.34 15