Instruction Manual. 32 HD Ready LED TV L32HE13. L32HE13_IB.indd 1 22/07/ :10

Transcription

1 Instruction Manual 32 HD Ready LED TV L32HE13 L32HE13_IB.indd 1 22/07/ :10

2 L32HE13_IB.indd 2 22/07/ :10

3 Contents Safety Warnings...5 Preparation...7 Unpacking the TV...7 Installing / Removing the Base Stand...8 Mounting the TV to a Wall...8 Front / Right Side View and Controls...9 Rear View and Sockets...10 Installing Batteries in the Remote Control...11 Remote Control Operation Range...11 Remote Control...12 Initial Setup...14 Turning the TV On for the First Time...14 Target Region Setting...15 Connecting an Analogue Device...15 Channel Selection...16 Display Channel Information...16 Volume Adjustment...16 Adjusting the Picture Settings...16 Aspect Ratio...18 Sound Setting...19 EPG (Electronic Programme Guide) (DTV Mode) Switch On / EPG Select a Programme Time Shift Recording onto a USB Storage Device...21 Recording DTV Programmes onto a USB Storage Device Timer Programming Playing Recorded Programmes Digital Teletext (DTV Mode) Teletext within Digital Service Listening to the Radio Signal Information (DTV Mode) CI (Common Interface) (DTV Mode) Software Update (Over Air Download) (DTV Mode) Software Update (USB) Time Settings Option Setting...31 OSD Language...31 TT Language...31 Audio Language (DTV Mode)...31 Subtitle Language (DTV Mode) Hearing Impaired PVR File System (DTV Mode) Blue Screen HDMI CEC (Consumer Electronics Control) (HDMI Mode) Restore Factory Default Lock Setting Lock System Set Password Block Channel Parental Guidance Key Lock L32HE13_IB.indd 3 22/07/ :10

4 Connecting a USB Storage Device Viewing Photos Listening to Music...41 Viewing Movies My Text Play Recorded Programme Maintenance...45 Hints and Tips...46 YPbPr Mode PC Mode HDMI Mode Specifications...49 L32HE13_IB.indd 4 22/07/ :10

5 Safety Warnings Safety Warnings Read all the instructions carefully before using the unit and keep them for future reference. Retain the manual. If you pass the unit onto a third party make sure to include this manual. Check that the voltage marked on the rating label matches your mains voltage. Damage Please inspect the unit for damage after unpacking. Do not continue to operate the unit if you are in any doubt about it working normally, or if it is damaged in any way - switch off, withdraw the mains plug and consult your dealer. Location of Unit The unit must be placed on a flat stable surface and should not be subjected to vibrations. Do not place the unit on sloped or unstable surfaces as the unit may fall off or tip over. The mains socket must be located near the unit and should be easily accessible. This unit is designed for indoor, domestic use only. Temperature Avoid extreme degrees of temperature, either hot or cold. Place the unit well away from heat sources such as radiators or gas / electric fires. Avoid exposure to direct sunlight and other sources of heat. Naked Flames Never place any type of candle or naked flame on the top of or near the unit. Moisture To reduce the risk of fire, electric shock or product damage, do not expose this unit to rain, moisture, dripping or splashing. No objects filled with liquids, such as vases, should be placed on the unit. If you spill any liquid into the unit, it can cause serious damage. Switch it off at the mains immediately. Withdraw the mains plug and consult your dealer. Ventilation To prevent the risk of electric shock or fire hazard due to overheating, ensure that curtains and other materials do not obstruct the ventilation vents. Do not install or place this unit in a bookcase, built-in cabinet or in another confined space. Ensure the unit is well ventilated. Make sure that there is a gap of at least 10 cm on both sides and a gap of 20 cm at the top. 20 cm 10 cm 10 cm 10 cm Safety Always disconnect the unit from the mains supply before connecting / disconnecting other devices or moving the unit. Unplug the unit from the mains socket during a lightning storm. Mains Cable Make sure the unit or unit stand is not resting on top of the mains cable, as the weight of the unit may damage the mains cable and create a safety hazard. If the mains cable is damaged it must be replaced by the manufacturer, its service agent, or similarly qualified persons in order to avoid a hazard. Interference Do not place the unit on or near appliances which may cause electromagnetic interference. If you do, it may adversely affect the operating performance of the unit, and cause a distorted picture or sound. Optimum Viewing View the unit in moderate light to prevent eye strain. It is recommended to watch the unit from a distance 3-7 times that of the screen height. LCD Screen The LCD screen is manufactured using high-precision technology. However, some tiny black points and / or bright points (red, blue or green in colour) may constantly appear on the LCD screen. These points are generated in the manufacturing process and are normal. Screen Burn A characteristic of Plasma and TV Panels is that displaying the same image for a long time may cause a permanent after-image to remain on the screen. This is called screen burn. Most pictures shown on the unit will be constantly moving and fill the screen. Examples of images that you need to watch out for are as follows (this is not an all-inclusive list): 1. Black Bars: If black bars appear at the left / right or top / bottom of the screen, it is recommended to change the format so that the picture fills the entire screen. 2. TV Channel Logos: e.g. Shopping channel logos and pricing displays - especially if they are bright and stationary. Moving or low-contrast graphics are less likely to cause ageing of the screen. 3. Time Displays 4. Teletext: Do not view a stationary page for long periods of time. 5. TV Menus 6. Pause Mode: Do not leave the screen in pause mode for long periods of time, e.g. when watching videos. To prevent screen burn if viewing any of the above for long periods of time, reduce contrast and brightness when viewing. Once burn-in occurs it will never disappear completely. 5 L32HE13_IB.indd 5 22/07/ :10

6 Standby The button on the remote control does not switch off the unit completely. The unit will continue to draw electricity from the mains supply while in standby. In the interests of safety and to avoid unnecessary energy consumption, never leave the unit in standby while unattended for long periods of time, e.g. overnight, while on holiday or while out of the house. Disconnect the mains plug from the mains socket. Batteries Batteries used in the remote control for this unit are easily swallowed by young children and this is dangerous. Keep loose batteries away from young children and make sure that the battery holder tray is secure in the remote control. Seek medical advice if you believe a cell has been swallowed. Please dispose of batteries correctly by following the guidance in this manual. The batteries shall not be exposed to excessive heat such as sunshine, fire or the like. Supervision Children should be supervised to ensure that they do not play with the unit and the remote control. Never let anyone especially children push anything into the holes, slots or any other openings in the case - this could result in a fatal electric shock. Service To reduce the risk of electric shock, do not remove screws. The unit does not contain any user-serviceable parts. Please leave all maintenance work to qualified personnel. Do not open any fixed covers as this may expose dangerous voltages. Maintenance Ensure to unplug the unit from the mains socket before cleaning. Do not use any type of abrasive pad or abrasive cleaning solutions as these may damage the unit s surface. Do not use liquids to clean the unit. The wall socket plug is used as a disconnect device, the disconnect device should be readily accessible. This equipment is a Class II or double insulated electrical appliance. It has been designed in such a way that it does not require a safety connection to electrical earth. To prevent the spread of fire, keep candles or other open flames away from this product at all times. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated dangerous voltage within the unit s enclosure that may be of sufficient magnitude to constitute a risk of electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the manual accompanying the unit. 6 L32HE13_IB.indd 6 22/07/ :10

7 (with DVD Player) Remove all packaging from the TV. Retain the packaging. If you dispose of it please do so according to local regulations. TV TV Stand Remote Control/AAA Batteries x 2 Screw x 5 Component Adapter Cable (YPbPr) Composite Adapter Cable (AV) Instruction Manual 1. Press and lift the back cover to open the battery compartment of the remote control. 2. Insert two AAA size batteries. Make sure to match the (+) and ( - ) ends of the batteries with the (+) and ( - ) ends indicated in the battery compartment. 3. Close the battery compartment cover. 1. Disconnect all cables connected to the TV. 2. Lay the TV down on a flat surface ideally on the edge of a table so the base of the TV slightly overhangs the edge of the table, with the back side facing up. Please make sure a soft cushioned material (such as a dry bath towel or thick piece of foam) is placed beneath the screen. 3. To install the TV stand, place the stand into the stand recess on the back of the TV. Table Cushioned material 4. Secure the stand using the 5 screws provided. screw in Screws x 5 Connect one end of the RF coaxial cable to the aerial socket on the wall and the other end of the cable to the AERIAL IN socket at the rear right bottom view of your TV. HDMI 1 In HDMI 2 In SCART Please ensure aerial is plugged in!! Then press OK button to start PC PC-RGB In RF In Audio In 1. The first time you turn the TV on, it will go 2. Press the buttons to select your straight into the First Time Installation menu. desired language to be displayed on the menu. The default on-screen menu language Please ensure the aerial is plugged in and is set as English. Press the OK button to then press the OK button. confirm. Tune Type UK Czech Finland France DTV Hungary Italy Denamrk Germany Netherlands Menu 3. To select the country option press the buttons. Press the OK button to confirm. Please select an OSD Language English Español Français Deutsch Português 1. Connect the mains cable to the mains socket after you have completed all the connections. 2. In standby mode, press the button on the remote control to turn the TV on. The red LED indicator will turn blue. To the mains socket England. 2. Press the OK button to highlight Secondary Region and press the buttons to select your preferred option (if available). 3. Press the OK button to confirm, and Tertiary Region will be highlighted. Press the buttons to select the your preferred option (if available). 4. Press the OK button to confirm. The main menu will be briefly displayed. Channel Tuning Your TV is now fully tuned in. TV : 0 Channel DTV : 0 Channel Radio : 0 Channel Target Region Setting Data : 0 Channel Country Code GBR 1 % MHz (DTV) Primary Region England Please press MENU key to skip Secondary Region London Tertiary Region 4. Channel tuning will commence. This operation may take up to 10 minutes. The display will show the progress of the tuning and the number of channels found. Well done, your new TV is now ready to use. You will find that there are many exciting features available. To get to know all these features, please take some time to read the instruction manual provided with your TV. If after reading the instruction manual you have additional questions related to the use of your TV please call our UK Call Centre on Our UK Customer Contact Centre is open Monday-Saturday 8am-8pm or Sunday 8am-6pm. QSG-L32HE13_HED V2 Italiano Target Region Setting During tuning your TV may have received signals from more than one transmitter. If this has occurred the Target Region Setting screen will be displayed. This will enable you to select the correct regional transmission for the local news service that you require. 1. Press the OK button to confirm the Country Code, this will highlight the Primary Region L32HED13_QSG.indd 1 11/04/ :45 HDMI R.VEAL SIZE PC Preparation Thank you for purchasing your new Logik 32 HD Ready LED TV. Your new TV has many features and incorporates the latest technology to enhance your viewing experience. We recommend that you spend some time reading this instruction manual so that you fully understand these features. You will also find some hints and tips to help you resolve any issues. Read all the safety instructions carefully before use and keep this instruction manual for future reference. Unpacking the TV Remove all packaging from the TV. Retain the packaging. If you dispose of it please do so according to local regulations. The following items are included: TV TV Stand Remote Control / AAA Batteries x 2 Red Blue Green Red White Yellow Screw x 5 Component Adapter Cable (YPbPr) Composite Adapter Cable (AV) Instruction Manual 32 HD Ready LED TV L32HE13 Quick Start Guide 32 HD Ready LED TV L32HE13 L32HED13 Connecting the Aerial Connecting to the Mains Socket Turning On and Tuning In the TV Unpacking Installing the Base Stand Operating Your Remote Control Instruction Manual Quick Start Guide If items are missing, or damaged please contact Partmaster (UK only). Tel: for assistance. 7 L32HE13_IB.indd 7 22/07/ :10

8 Installing / Removing the Base Stand The LCD display is very fragile, and must be protected at all times when installing and removing the base stand. Be sure that no hard or sharp object, or anything that could scratch or damage the LCD display, comes into contact with it. DO NOT exert pressure on the front of the TV at any time because the screen could crack. 1. Disconnect all cables connected to the TV. 2. Lay the TV down on a flat surface ideally on the edge of a table so the base of the TV slightly overhangs the edge of the table, with the back side facing up. Please make sure a soft cushioned material (such as a dry bath towel or thick piece of foam) is placed beneath the screen. 3. To install the TV stand, place the stand into the stand recess on the back of the TV. Table Cushioned material 4. Secure the stand using the 5 screws provided. screw in Mounting the TV to a Wall Screws x 5 Remove the stand assembly before mounting the TV onto the wall. 1. To remove the stand assembly, untighten the 5 screws holding the stand assembly to the rear of the TV. Slide the stand assembly out. unscrew Keep all the spare screws should you want to use the stand assembly option. Screw x 5 2. Mounting on the wall. This TV is designed to be wall-mounted with a standard 100 mm x 100 mm mounting kit (sold separately) designed for flat-panel TVs. Mount this TV according to the instructions included in the mounting kit. Due to space restrictions, we recommend that you make all connections before mounting on to the wall. 100 mm 100 mm Four mounting holes (size M6 screw) Please read this instruction manual carefully while setting up your TV. If you require additional assistance please call our UK Call Centre on Our UK Customer Contact Centre is open Monday-Saturday 8am-8pm or Sunday 8am-6pm. 8 L32HE13_IB.indd 8 22/07/ :10

9 Front / Right Side View and Controls Item 1 POWER LED 2 IR (Infrared Receiver) 3 SOURCE Description Illuminates blue when the TV is turned on. Illuminates red when the TV is in standby mode. The LED will illuminate blue and then blink red and blue confirming that a timer recording programme has started in the standby mode. Receives IR signals from the remote control. Do not put anything near the sensor, as its function may be affected. Press to select among different input signal sources: DTV / ATV / AV / SCART / YPBPR / HDMI 1 / HDMI 2 / HDMI 3 / PC / USB. Confirmed the selection on OSD menu. 4 MENU Displays the OSD (on screen display) menu. 5 V + / Adjusts the volume. Press to select and adjust a setting in the OSD menu. 6 CH + / Press to select a channel or select a sub-menu from the OSD menu. 7 STANDBY Switches the TV on or into standby mode. 9 L32HE13_IB.indd 9 22/07/ :10

10 Rear View and Sockets AV IN YPbPr 5 6 CI CARD IN 7 USB HDMI 3 In 1 8 Coaxial Out 9 HDMI 1 In HDMI 2 In SCART PC Audio In PC-RGB In RF In Item 1 HDMI 1 / HDMI 2 / HDMI 3 Description Connects to a High-Definition (HD) signal output device, such as a set-top box, blu-ray disc player or AV receiver. 2 SCART Connects to a VCR, DVD Player, or other AV device with a SCART output socket. 3 PC-RGB In / PC AUDIO In Connects to a computer or other devices with a VGA interface. 4 RF In Connects to the aerial socket on the wall with the RF coaxial cable. 5 YPbPr Connects to a DVD player, Digital Set-Top-Box, or other AV devices with component (YPbPr) video and audio output sockets. 6 AV IN Connects to the Composite output sockets on external video devices. 7 CI CARD In Allows the insertion of a Common Access Module. 8 USB Allows the insertion of a USB storage device to play video, audio, photo and text files (USB mode) and record DTV programmes on to a USB storage device. 9 Coaxial Out Connects to the audio socket on the digital/standard 5.1 audio system. 10 L32HE13_IB.indd 10 22/07/ :10

11 HDMI Installing Batteries in the Remote Control 1. Press and lift the back cover to open the battery compartment of the remote control. 2. Insert two AAA size batteries. Make sure to match the (+) and ( - ) ends of the batteries with the (+) and ( - ) ends indicated in the battery compartment. 3. Close the battery compartment cover. Handling the Batteries Improper or incorrect use of batteries may cause corrosion or battery leakage, which could cause fire, personal injury or damage to property. Only use the battery type indicated in this manual. When the batteries are exhausted, the remote will not function. Replace both batteries at the same time with new ones. Do not install new batteries with used ones and do not mix different types of batteries. Do not dispose of used batteries as domestic waste. Dispose of them in accordance with local regulations. Handling the Remote Control Take care of your fingernails when you press and hold the battery release tab. Do not drop or cause impact to the remote control. Do not spill water or any liquid on the remote control. Do not place the remote control on a wet object. Do not place the remote control under direct sunlight or near sources of excessive heat. Remove the battery from the remote control when not in use for a long period of time, as it could cause corrosion or battery leakage and may result in physical injury and/or property damage including fire. Remote Control Operation Range Point the remote control at the TV no more than 5 metres from the remote control sensor on the TV and within 60 in front of the TV. The operating distance may vary depending on the brightness of the room M 11 L32HE13_IB.indd 11 22/07/ :10

12 Remote Control 1. Switch the TV between on and standby mode. 2. MUTE Mute and restore your TV sound Number Button Press to select a programme. (DTV / RADIO mode) 4. -/-- Feature not available. 5. RECALL Return to the previous viewing channel. (DTV mode) 6. TV GUIDE Display the EPG (Electronic Programme Guide). (DTV mode) 7. VOL + / Adjust the volume. 8. CH + / Select a channel. 9. FAV Display the favourite channel list. (DTV mode) 10. DTV (TV/RADIO) A short-cut to switch input source to TV / Digital radio channels. (DTV mode) 11. HDMI A short-cut to switch input source to HDMI 1, 2, or PC A short-cut to switch input source to PC. 13. USB A short-cut to switch input source to TV / Digital radio channels. (DTV mode) 14. SOURCE Select among the different input signal sources: DTV / ATV / AV / SCART / YPBPR / HDMI 1 / HDMI 2 / HDMI 3 / PC / USB. 15. INFO Display the present channel information such as the current time and channel name. (DTV mode) 16. Allow you to navigate the OSD menus and adjust the system settings to your preference. OK Confirm the selection in the OSD menus. Display channel list. (DTV / RADIO mode) 17. MENU Display the OSD (On Screen Display) menu. Return to the previous menu in the OSD menus. 18. Exit Exit the OSD menu HDMI R.V EAL SIZE PC L32HE13_IB.indd 12 22/07/ :10

13 19. SLEEP Set the TV sleep timer: OFF / 10 / 20 / / 180 / 240 min. 20. ASPECT Watch the screen in various formats: Auto / 4:3 / 16:9 / Zoom / Smart Zoom / Subtitle. 21. AUDIO Switches between the audio languages (only applicable when the TV programme / disc has this features). (DTV ) 22. SUBTITLE Select subtitles which are broadcast with the programme. (DTV mode) 23. To skip to the beginning of the previous track / photo. (USB mode) 24. Record the current programme. (DTV mode) 25. To skip to the beginning of the next track / photo. (USB mode) 26. To stop the playback or recording. (DTV / USB mode) 27. To reverse playback rapidly. (USB mode) 28. REC LIST Display the record list. (DTV mode) 29. To advance playback rapidly. (USB mode) 30. To start the timeshift playback. (DTV mode) To start playback or pause. (DTV mode) 31. S.MODE Short cut to preset sound modes. 32. P.MODE Short cut to preset picture modes. 33. INDEX Function not available. 34. R.VEAL Function not available. 35. TEXT Turn on and off the teletext function. (DTV mode) 36. TEXT HOLD Freeze a multi-page passage on screen in teletext. (Feature not available) 37. DISPLAY Switches the display on/off. (Radio mode) 38. SIZE Function not available. 39. Coloured buttons Access the TELETEXT items ( DTV mode) or menu options HDMI R.V EAL SIZE PC L32HE13_IB.indd 13 22/07/ :10

14 Initial Setup Turning the TV On for the First Time 1. Connect one end of the RF coaxial cable to the aerial socket on the wall and the other end of the cable to the AERIAL IN socket at the rear right bottom view of your TV. Do not connect the TV to the mains supply until you have completed all the connections. OR RF coaxial cable (not included) HDMI 1 In HDMI 2 In SCART PC Audio In PC-RGB In RF In 2. Connect the mains cable to the mains socket after you have completed all the connections. 3. In standby mode, press the button on the remote control to turn the TV on. The red LED indicator will turn blue. To the mains socket Always disconnect the TV from the mains socket when not in use for a long period of time. The STANDBY button on the front right side panel of the TV or the button on the remote control is only used for switching the TV into standby, it does not disconnect the TV from the mains power. To completely disconnect the mains power, please remove the mains plug from the mains socket. 4. The first time you turn the TV on, it will go straight into the First Time Installation menu. Please ensure the aerial is plugged in and then press the OK button. (If you have already installed the TV using the Quick Start Guide, please skip this section). Please ensure aerial is plugged in!! Then press OK button to start 5. Press the buttons to select your desired language to be displayed on the menu. The default on-screen menu language is set as English. Press the OK button to confirm. Please select an OSD Language English Español Français Deutsch Português Italiano 6. To select the country option press the buttons. Press the OK button to confirm. Tune Type DTV UK Finland Hungary Czech France Italy Denamrk Germany Netherlands 14 Menu L32HE13_IB.indd 14 22/07/ :10

15 7. Channel tuning will commence. This operation may take up to 10 minutes. The display will show the progress of the tuning and the number of channels found. If you want to exit the tuning menu, press the MENU button to interrupt the tuning process. A pop-up screen will be displayed, press the button. 8. After tuning is complete, the channels are arranged in a preset order. If you wish to skip channels, modify the preset order or add them as favourite channel, select Channel Edit under the Channel menu. Channel Tuning DTV : 0 Channel Radio : 0 Channel DATA : 0 Channel 1 %... UHF CH 1 (DTV) Please press MENU key to skip Target Region Setting During tuning your TV may have received signals from more than one transmitter. If this has occurred the Target Region Setting screen will be displayed. This will enable you to select the correct regional transmission for the local news service that you require. 1. Press the OK button to confirm the Country Code, this will highlight the Primary Region England. Target Region Setting Country Code GBR Primary Region England Secondary Region London Tertiary Region 2. Press the OK button to highlight Secondary Region and press the buttons to select your preferred option (if available). 3. Press the OK button to confirm, and Tertiary Region will be highlighted. Press the buttons to select the your preferred option (if available). 4. Press the OK button to confirm. The main menu will be briefly displayed. Your TV is now fully tuned in. CHANNEL PICTURE Country Code Primary Region Secondary Region Tertiary Region This will be shown as GBR for the UK. This will show the regional country (England, Wales, Scotland, NI). This will allow you to set the region for your local news service on BBC and ITV (London, Beds and Cambs etc). You may receive signals from more than one transmitter within the Secondary Region, (e.g Beds and Cambs may have Luton or Sandy Heath). SOUND TIME OPTION LOCK EXIT Connecting an Analogue Device If you have connected an analogue device such as a video recorder via the aerial socket on you TV you will have to tune it in using ATV mode. Ensure the device is switch on before you start the tuning process. 1. Press the SOURCE button, press the buttons to select ATV and press OK. ATV Manual Tuning Channel Edit Software Update(OAD) Software Update(USB) 2. Press the MENU button, then press the buttons to select CHANNEL and press OK. 3. Press the buttons to select ATV MANUAL TUNING and press OK. 4. Press the buttons to select SEARCH then press one of the buttons to start the search for your device. The search will automatically stop when the device is found. ATV Manual Tuning Current CH 1 Colour System PAL Sound System I 5. Press the EXIT button to exit the menu. Fine - Tune AFC Search MHz 15 L32HE13_IB.indd 15 22/07/ :10

16 Channel Selection Press the CH + / buttons on the remote control repeatedly or the 0-9 buttons to select the channel. Alternative Press the OK button to enter the Channel List. Then use the Press the OK button to view the selected channel. buttons to highlight and select the channel. If a blocked channel is selected, the password screen will be displayed. Press the 0-9 buttons to enter the password, the channel will then be unlocked (refer to Block Channel for details). Press the FAV button to view the Favourite List. Then use the buttons to highlight and select the channel. Press the OK button to view the selected channel, the Favourite List will be blank unless you have added your favorites. Press the button to return to the previously viewed channel. Display Channel Information Press the INFO button to view the current information. Volume Adjustment Press the V + or button on the right side panel of the TV or the VOL + or button on the remote control to adjust the volume. If you wish to switch the sound off, press the MUTE button. Press the MUTE button again or the VOL + or button to resume audio listening. Adjusting the Picture Settings Allows you to set your preferred picture mode. 1. Press the MENU button and then press the buttons to select the PICTURE menu and then press the OK button. CHANNEL PICTURE SOUND TIME OPTION LOCK EXIT 2. Press the buttons to select the following picture options and then press the OK button. Press the buttons to adjust the levels in the menus. Picture Mode Contrast Brightness Colour Tint Sharpness Colour Temp Noise Reduction SCREEN Standard Normal 16 L32HE13_IB.indd 16 22/07/ :10

17 BACK BACK BACK EXIT EXIT EXIT MENU MENU MENU Picture Mode Select among picture mode: Standard / Mild / Personal / Dynamic. The default setting is Standard. Select Personal if you want to adjust the picture settings yourself. Picture Mode Dynamic Standard Mild Personal Contrast Brightness Colour Tint (For NTSC format) Sharpness Colour Temperature Adjusts the difference between light and dark levels in the picture. (for Personal mode) Increases or decreases the amount of white in the picture. (for Personal mode) Controls the colour intensity. (for Personal mode) Adjusts the balance between red and green levels. (Tint is only available for NTSC signal input via the SCART or AV IN.) Adjusts the level of crispness in the edges between light and dark areas of the picture. (for Personal mode) Select among colour temperature: Cold / Normal / Warm. Adjusts the colour components independently to achieve a warm or cool colour. (for Personal mode) Cold: Increases blue tint Normal Warm: Increases red tint Colour Temp Cold Normal Warm Noise Reduction Reduces the noise level of the connected device: / Low / Middle / High. Noise Reduction Low Middle High Screen (PC mode) Adjusts the PC desktop content. Auto Adjust H-set V-set Size Phase Position Reset Allows you to synchronise a PC signal automatically. Adjusts the position of the picture left and right in the window. Adjusts the position of the picture up and down in the window. Adjusts the picture horizontally, in linear properties Controls the signal phase, which can improve focus clarity and image stability based on the PC mode. Press to set the best screen position. 3. Press the MENU button to return to the previous menu, press again to return to the main menu. 4. Press the EXIT button to exit the menu. Auto Adjust H-set V-set Size Phase Position Reset L32HE13_IB.indd 17 22/07/ :10

18 Aspect Ratio Allows you to watch the screen in various picture formats: Auto / 4:3 / 16:9 / Zoom / Smart Zoom / Subtitle. The default setting is AUTO. HDMI 1. Press the ASPECT button to scroll through the aspect rations. The aspect Ratio can also be selected from the OPTION menu. Auto This selection will display the picture according to the aspect ratio of the input source. Black bars will appear on both the left and right of the screen. 4:3 This selection will allow you to view a picture with an original 4:3 aspect ratio. Black bars will appear on both the left and right of the screen. 16:9 This selection will allow you to adjust the picture horizontally, in linear proportion, to fill the entire screen. Zoom This selection will allow you to zoom in the picture without any alteration, while filling the entire screen. However, the top and bottom of the picture will be cropped. Smart Zoom This selection is similar to 16:9 mode, but the picture slightly stretches horizontally and clips off a little from the top and bottom. Subtitle This selection will allow you to zoom in the picture without any alternation, while filling the entire screen with subtitles shown at the bottom of the screen. Input Signal 4:3 Input Signal 16:9 This selection will display the picture according to the aspect ratio of the input source. This selection will allow you to adjust the picture horizontally, in linear proportion. Black bars will appear on both the left and right of the screen. This selection will allow you to view a picture with an original 16:9 aspect ratio. This selection will allow you to zoom in the picture without any alteration, while the 4 sides of the picture will be cropped. This selection is similar to 4:3 mode, but the picture slightly stretches vertically and clips off a little from the top and bottom. This selection will allow you to zoom in the picture without any alternation, while showing subtitles at the bottom of the screen. 18 L32HE13_IB.indd 18 22/07/ :10

19 BACK EXIT MENU Sound Setting Allows you to adjust the sound settings on your TV. 1. Press the MENU button and then press the buttons to select the SOUND menu and then press the OK button. CHANNEL PICTURE SOUND TIME OPTION LOCK EXIT 2. Press the buttons to select the following sound options and then press the OK button. Sound Mode Treble Bass Balance Standard Auto Volume On SRS TruSurround HD On SPDIF Mode Auto AD Switch 3. Press the buttons to adjust each option s setting. Sound Mode Allows the selection of an audio-enhancement technique: Standard / Music / Movie / Sports / Personal. Sound Mode Standard Music Movie Sports Personal Treble Bass Balance Auto Volume SRS SPDIF Mode AD Switch (For DTV mode) Controls the relative intensity of higher pitched sounds. (for Personal mode) Controls the relative intensity of lower-pitched sounds. (for Personal mode) Adjusts the relative volume of the speakers in a multiple speaker system. Volume levels are automatically controlled (e.g., advertisements tend to be louder than the programmes). SRS TruSurround HD (TS HD) is a robust multichannel virtualisation technology developed by SRS Labs that provides an enhanced listening experience unlike any other technology that has been offered for a two speaker playback environment. TruSurround HD builds upon its predecessor, the industry leading surround sound virtualiser, SRS TruSurround XT. Not only does TruSurround HD process up to 6.1 channels for playback over two speakers or headphones, but it also utilises additional proprietary algorithms from SRS Labs to optimise bass performance, for deep rich bass, dialogue clarity for better intelligibility of vocals, and definition control for maximum high-frequency clarity. Press the OK button to select On /. Selects the digital audio output mode. Audio Description is an auxiliary audio function that provides an additional audio track for visually challenged persons. This function handles the Audio Stream for the AD (Audio Description), when it is sent along with the main audio from the broadcaster. Set to for normal broadcasting sound coming out from speakers. Set to On to activate the description sound track if available. The availability of Audio Description sound track is indicated by the visually impaired icon "V.I." in the information banner. When you select ON you can adjust the volume of the Audio Description by pressing the buttons. 4. Press the MENU button to return to the previous menu, press again to return to the main menu. 5. Press the EXIT button to exit the menu. 19 L32HE13_IB.indd 19 22/07/ :10

20 EPG (Electronic Programme Guide) (DTV Mode) This system has an Electronic Programme Guide (EPG) to help you navigate through all the possible viewing options. The EPG supplies information such as programme listings, start and end times for all available services. In addition, detailed information about the programme is often available in the EPG (the availability and amount of programme information will vary, depending on the particular broadcaster). This function can be used only when the EPG information is broadcast by broadcasting companies. The EPG displays the programme details for the next 7 days. Switch On / EPG 1. Press the TV GUIDE button to switch on EPG. 2. Press the TV GUIDE button or the EXIT button again to switch off EPG and return to normal TV viewing. current date and time channel no. and channel name PROGRAMME GUIDE 1 BBC ONE 25 Dec :06 10:00-10:15 Pinky and Perky 25 Dec DTV 10:00 11:00 1 BBC ONE Pinky and perky Frankenstei.. No information 2 BBC TWO My Fair Lady 7 BBC THREE This is BBC THREE 70 CBBC Channel Bear Behaving Badly Shaun the.. No information 80 BBC NEWS BBC News Our World: Stormchaser 105 BBC Red Button BBC Red Button current channel name current programme title programme date programme time programme information Select a Programme Press the buttons to select the desired channel and then press the buttons to select the desired programme. Press the OK button to confirm. Button Functions in a 7-Days Guide Remote Control Button RED (Record) GREEN (Schedule) Function Timer Programming See page 23 for details on Timer Programming. Press the RED button in the Schedule List to delete the selected preset reminder. Press the GREEN button to view Schedule List 15:30 10th Mar Delete Back the preset reminders or scheduled recordings in the Schedule list. Press the GREEN button again to return to the EPG. Time Date Programme Title Channel Name YELLOW (Date) BLUE (Remind) INFO or or OK TV GUIDE / EXIT Press the YELLOW button and then press the buttons to view the schedule of the previous / next day. Press the YELLOW button again to return to the EPG. Press the BLUE button while on the selected programme, Reminder setting the Reminder setting menu will be displayed. _ 15 Film 4 Press the buttons to adjust the settings and + 05 Hour then press the OK button to confirm the settings. After 08 Minute confirmation, the Schedule list will then be displayed with 28 Date your preset reminders shown. Press the GREEN button to Apr Month return to the EPG. The TV will automatically tune to the Once Mode selected programme when it starts. Press to display detailed information of the selected programme (if available). Press to select a channel. Press to select a programme. Press to confirm and view the selected channel. Press to switch off the EPG. OK BACK 20 L32HE13_IB.indd 20 22/07/ :10

21 Time Shift Recording onto a USB Storage Device This function allows you to pause live TV. The picture will pause and the programme will begin recording so you don't miss any of the programme. You will have to have a USB storage device attached to the USB socket for Time Shift Recording to work. Time Shift Mode and Recording functions may not work if the signal strength is weak. Stop the time shift function before switching to another input source. If the transfer rate of the USB storage device is too slow for recording or time shift function, a warning statement will be shown on the screen. If this happens, please upgrade your USB storage device. The minimum transfer speed is 5MB/s. While watching your TV, you may press the button to pause the live programme if you want to go out for a while (e.g. going to the bathroom / kitchen). " " will show on the screen. When you have returned, press the button to play the missed broadcast programme. " " will show on the screen. The video and sound may have a little bit of delay or be out-of-sync for a few seconds when the unit starts to playback the missed programme. It will soon turn to normal. Alternative Press the OK button to display the PVR Time Shift progress bar and then press the buttons to select " Play" on the bar. Press the OK button to confirm The PVR Time Shift Progress Bar 1 Indicates the status of the currently displayed video ( / / / ) 2 Indicates the time lagging behind the live broadcast (PVR reviewing) 3 Indicates the available recording time on your USB storage device 4 Indicates the current time Using the Remote Control You can shift playback to any point of the virtually recorded programme. The PVR Time Shift progress bar will be displayed on the screen for 15 seconds. Press the OK button to display the PVR Time Shift progress bar again. or When playing, Press the button repeatedly to speed up x 2 / x 4 / x 8 / x 16. Press the button repeatedly to speed up x 2 / x 4 / x 8 / x 16. During fast forward / fast backward state, press the button to return to normal playback. or Press the button to jump about 10% forward. Press the button to jump about 10% back. During playback, press the button to display a still screen and then press the button again to resume playback. During fast forward / fast backward state, press the button to return to normal playback. OK During playback, press the OK button to display a still screen and then press the button again to resume playback. If you want to exit the PVR Time Shift progress bar and return to the current live broadcast, press the button and then press the button to confirm. 21 L32HE13_IB.indd 21 22/07/ :10

22 Recording DTV Programmes onto a USB Storage Device Use this function to record the DTV programme you are watching on the main screen and save it for future viewing. The recording from timer programme or direct recording may have a little bit of delay when it starts to record the broadcast programme. Please make sure the USB device is inserted. If not, a warning message will pop up. 1. Press the button to record the programme that you are currently watching. The recording progress bar will disappear after 15 seconds. To display the recording progress bar again, press the OK button or the button. 2. Press the button to stop recording. Recording will stop automatically when the disk is full. If you want to turn off your TV during recording, press the button. A dialogue will display. The recording is still inprogress. Do you want to switch off the TV? Yes, Stop recording and switch off the TV Yes, turn off the screen and sound but keep recording the programme No Press the buttons to select your desired option and then press the OK button to confirm. If you select the middle option in the box, the screen will turn off but the recording will still be in progress, the LED indicator will alternatively flash red and blue. 22 L32HE13_IB.indd 22 22/07/ :10

23 Timer Programming This function is used to perform scheduled recording. The recording from timer programme or direct recording may have a little bit of delay when it starts to record the broadcast programme. Please make sure the USB device is inserted. If not, a warning message will pop up. 1. Press the TV GUIDE button on the remote control. The EPG menu will appear. Press the buttons to select the desired programme to record. PROGRAMME GUIDE 1 BBC ONE 25 Dec :06 10:00-10:15 Pinky and Perky 25 Dec DTV 10:00 11:00 1 BBC ONE Pinky and perky Frankenstei.. No information 2 BBC TWO My Fair Lady 7 BBC THREE This is BBC THREE 70 CBBC Channel Bear Behaving Badly Shaun the.. No information 80 BBC NEWS BBC News Our World: Stormchaser 105 BBC Red Button BBC Red Button 2. Press the button or the RED button on the remote control while on the selected programme, the RECORDER menu will be displayed. The recording time for the selected programme will be automatically set. If you want to adjust the time press the buttons to select the settings in the RECORDER menu for the Channel, Start time, End time and Mode. Channel Display the channel that you wanted to record. Start time Press the buttons to select the Hour / Minutes / Date / Month and then press the buttons to adjust the start time. RECORDER 1 BBC ONE Start Time 10 Hour 00 Minute 25 Date Dec Month End Time 10 Hour End time Press the buttons to select the Hour / Minutes / Date / Month and then press the buttons to adjust the start time Mode Press the buttons to select the Once / Everyday / Weekly. 15 Minute 25 Date 25 Date Dec Month Mode Once Back 3. After finishing all the recorder adjustments, press the OK button to confirm your settings. A Timer Save Success screen will display. Timer Save Success BBC 1 25 DEC :00 If you see the 'Pls connect USB first' display then you must connect a USB storage device and set the recording again or your recording will NOT record. 4. The Schedule List will be displayed, to remove the list press the GREEN button. Pls connect USB first BBC 1 25 DEC :00 When the preset time is reached, the TV will start recording automatically. If a programme recording starts when the TV is in standby mode, the LED indicator will alternatively flash red and blue. 23 L32HE13_IB.indd 23 22/07/ :10

24 Playing Recorded Programmes The recorded List shows a list of all the recordings that have been made. You can view all your recordings from this list and see information about each recording. 1. Press the REC List button on the remote control. The Recorded List menu will appear. Press the buttons to select the desired recorded programme. 2. Press the OK button to view the recording. To see more information about a recording press the GREEN button or the button. To delete a recording, highlight the recording you wish to delete and press the RED button. You can view the Recorded List in 3 different orders. Press the REC LIST button to change the order. Programme View - This will list the recordings in alphabetical order. Channel View - This will list the recordings in channel order. Time View - This will list the recordings in date order. Recoded List Doctor Who This Morning Neighbours 25 Date Delete Programme Info REC LIST Playback Controls You can play, pause, fast forward, fast rewind and skip forwards and backwards in 30 second increments. or When playing, Press the button repeatedly to speed up x 2 / x 4 / x 8 / x 16. Press the button repeatedly to speed up x 2 / x 4 / x 8 / x 16. During fast forward / fast backward state, press the button to return to normal playback. or Press the button to jump forward 30 seconds. Press the button to jump back 30 seconds. OK During playback, press the button to display a still screen and then press the button again to resume playback. During fast forward / fast backward state, press the button to return to normal playback. During playback, press the OK button to display the recording progress bar. It the recording progress bar is already displayed pressing the OK button will pause the recording. Press the button to resume playback. If you want to stop the recording and return to the current live broadcast, press the then press the button to confirm. button and 1. Press any one of the Playback Controls on the remote control and the playback control menu will appear at the bottom of the screen. You can now press any of the playback controls on the remote control or press to highlight the button on the screen then press OK. 2. Press the EXIT button to remove the Playback Control menu. [00:00:33/00:04:22] Play FB FF Prev. Next Pause Stop 06:18 24 L32HE13_IB.indd 24 22/07/ :10

25 Digital Teletext (DTV Mode) Digital teletext can access special digital teletext services and specific services which broadcast digital teletext. You will need to turn off Subtitle Function before using teletext (refer to page 32 for details). Teletext within Digital Service 1. In DTV mode press the TEXT button to display teletext page. 2. Follow the instructions on digital teletext page and move around the page by pressing, OK, RED, GREEN, YELLOW, BLUE or 0-9 buttons etc. To change digital teletext services, you will need to exit the current text service and change channels. Then enter the text service on the newly selected channel. Alternative You may press the RED button to display the teletext information when you see a red "press " logo in the top right corner of the screen (e.g. BBC services). This will now display the teletext menu and available information categories. To access the pages, use navigation buttons to highlight item required and press the OK button to select. Follow on screen prompts for other functions. 3. Press the TEXT button to exit. Listening to the Radio You can listen to radio stations through your TV. 1. Press the TV/RADIO button to select radio mode. If you want to remove the radio display from your TV screen press the DISPLAY button, this will hide the display. To see the display again press DISPLAY. B B C RADIO Now Playing: 22 by Taylor Swift Scott Mills For programme info, events & news, press RED 2. Press the CH +/- buttons to change radio stations or press the TV GUIDE button to see all the stations in the Programme Guide. You will NOT be able to record any radio stations. PROGRAMME GUIDE 1 BBC Radio 1 25 Dec :06 13:00-16:00 Scott Mills 25 Dec Radio 10:00 11: BBC Radio 1 Scott Mills Greg James 701 BBC R1X My Fair Lady 702 BBC Radio 2 Steve Wright in the Afternoon 703 BBC Radio 3 Afternoon on BBC Radio 4 Programme The Concrete The Food and the Divine 705 BBC R5L Richard Bacon Drive 25 L32HE13_IB.indd 25 22/07/ :10

26 Signal Information (DTV Mode) Allows you to view the signal information. 1. Press the MENU button and then press the buttons to select the CHANNEL menu and then press the OK button. CHANNEL PICTURE SOUND TIME OPTION LOCK EXIT 2. Press the buttons to select Signal Information and then press the OK button to view the signal information. Auto Tuning DTV Manual Tuning Channel Edit Signal Information CI Information Software Update(OAD) Software Update(USB) 3. Press the MENU button to return to the previous menu, press again to return to the main menu. 4. Press the EXIT button to exit the menu. Signal Information Channel 50 Frequency Mhz Quality 99 Strength 91 Network Crystal Palace CI (Common Interface) (DTV Mode) The common interface allows the use of a Common Access Module to enable you to view scrambled (pay to view) services. These services are provided by TopUp TV (UK only) and others. The Common Access Module and viewing card can be obtained from the service provider. Do not repeatedly insert or remove the Common Access Module as this may damage the interface and cause a malfunction. Coaxial Out USB HDMI 3 In Rear Right Side View of TV CI CARD IN AV IN YPbPr This feature is not available in all countries. To insert the Common Access Module 1. Before you insert the Common Access Module, ensure that the TV is switched off and the viewing card is inserted in accordance with the Service Provider s instructions. CI (Common Interface) Allows the Common Access Module to be inserted and access the content that has been encrypted. CI CARD IN 2. Insert the Common Access Module into the slot. Flip the Common Access Module to another side and try again if you feel resistance. 3. Switch the TV on. To remove the Common Access Module 1. Before you remove the Common Access Module, ensure that the TV is switched off at the mains. 2. Pull the Common Access Module from the slot. Common Access Module 3. Switch the TV on. 26 L32HE13_IB.indd 26 22/07/ :10