an ISO 9001: 2008 Registered Company COMPRESSOR/ALTERNATOR BRACKET KIT with LATE-MODEL SAGINAW POWER STEERING PUMP

Transcription

1 an ISO 900: 00 Registered Company MOPAR B/RB COMPRESSOR/ BRACKET KIT with LATE-MODEL SAGINAW POWER STEERING PUMP 600 COMPRESSOR SAGINAW POWER STEERING PUMP 9000 REV C 5//4 INSTRUCTIONS, BRACKET KIT 600, PG OF 9

2 Table of Contents PAGES. COVER. TABLE OF CONTENTS 3. B/RB MOPAR INSTALLATION 4. B/RB MOPAR INSTALLATION (CONT.) FIGURES & a 5. COMPRESSOR/POWER STEERING INSTALLATION FIGURES & a 6. B MOUNT INSTALLATION FOR 350, 36, 33, 400 MOPAR FIGURE 3 7. RB MOUNT INSTALLATION FOR 43, 46, 440 MOPAR FIGURE 4. B/RB MOPAR BELT ROUTING 9. PACKING LIST 9000 REV C 5//4 INSTRUCTIONS, BRACKET KIT 600, PG OF 9

3 B/RB MOPAR INSTALLATION B: 9.9 DECK HEIGHT (350, 36, 33, 400) RB: 0.75 DECK HEIGHT (43, 46, 440) THIS BRACKET IS DESIGNED FOR MOPAR B/RB WITH LATE-MODEL SAGINAW-STYLE POWER STEERING. USE WITH OEM -GROOVE WATER PUMP PULLEY AND OEM 4-GROOVE CRANKSHAFT PULLEY. IF PULLEYS ARE NEEDED, THE FOLLOWING ARE AVAILABLE FROM VINTAGE AIR: GROOVE CRANKSHAFT PULLEY GROOVE WATER PUMP PULLEY 5-7/3 CYL HEAD TO COMP GRV 5-7/3 CYL HEAD TO COMP GRV IDENTIFY WATER PUMP HOUSING BEFORE PROCEEDING TO COMPRESSOR/BRACKET INSTALLATION INSTRUCTIONS. THE SHORT BOSS HOUSING REQUIRES WASHERS AND/OR SPACERS TO ACHIEVE DESIRED THICKNESS OF 5/3 LENGTH. NOTE: ASSEMBLE ALL BRACKETS LOOSELY TO ENGINE BEFORE TIGHTENING BOLTS. THIS WILL ENSURE PROPER ALIGNMENT OF ALL BRACKETS. 5/3 LONG BOSS LESS THAN 5/3 SHORT BOSS REV C 5//4 INSTRUCTIONS, BRACKET KIT 600, PG 3 OF 9 3-/ ENG BLOCK TO ST GRV OF CS PULLEY 4-/ ENG BLOCK TO ND GRV OF CS PULLEY 5 ENG BLOCK TO 3RD GRV OF CS PULLEY 5-5/ ENG BLOCK TO 4TH GRV OF CS PULLEY

4 B/RB MOPAR INSTALLATION (CONT.) LONG BOSS COMPRESSOR/BRACKET INSTALLATION: WATER PUMP HOUSING WITH LONG BOSS HOUSING ( 5/3 LENGTH), WITH POWER STEERING. INSTALL COMPRESSOR/BRACKET AS SHOWN ON PAGE 5. SHORT BOSS COMPRESSOR/BRACKET INSTALLATION: WATER PUMP HOUSING WITH SHORT BOSS HOUSING, WITH POWER STEERING. INSTALL COMPRESSOR/BRACKET AS SHOWN ON PAGE 5. POWER STEERING WITH SAGINAW PUMP: KIT IS DESIGNED FOR LATE-MODEL SAGINAW-STYLE POWER STEERING AND OEM BRACKET ADJUSENT. REMOVE WELDED NUT FROM REAR POWER STEERING BRACKET BEFORE INSTALLING COMPRESSOR REAR BRACKET AS SHOWN IN FIGURE, BELOW. SLOT FRONT POWER STEERING BRACKET FOR BOLT CLEARANCE. SEE FIGURE a, BELOW. REAR POWER STEERING BRACKET IS IN OEM POSITION..50L SPACERS ARE NECESSARY BETWEEN FRONT POWER STEERING BRACKET AND POWER STEERING PUMP. ADD ADDITIONAL WASHERS IF NECESSARY. REMOVE WELDED NUT OEM REAR POWER STEERING BRACKET PS BRACKET CENTER AXIS LATE SAGINAW PS BRKT FIGURE.750 FOR REFERENCE FRONT VIEW *AREA TO BE REMOVED FROM POWER STEERING BRACKET*. LOCATE ENDS OF SLOT. DRILL / PILOT HOLES FOLLOWED BY 7/6 HOLES.. ONCE ENDS OF SLOT ARE DRILLED TO SIZE, REMOVE REMAINING MATERIAL BETWEEN HOLES CREATING THE SLOT AS ILLUSTRATED. FIGURE a SCRIBE CENTERLINES AS SHOWN. POWER STEERING WITH FEDERAL PUMP: VINTAGE AIR POWER STEERING BRACKET KIT #600 IS REQUIRED. SAGINAW PUMP 9000 REV C 5//4 INSTRUCTIONS, BRACKET KIT 600, PG 4 OF 9 FEDERAL PUMP 4

5 COMPRESSOR/POWER STEERING INSTALLATION REFER TO HARDWARE PACKING LIST FOR NUMBERED PART DESCRIPTIONS BB MOPAR FRONT COMPRESSOR BRKT BB MOPAR REAR COMPRESSOR BRKT 6600 WATER PUMP HOUSING 4 LATE-MODEL SAGINAW-STYLE POWER STEERING REAR BRKT 6 FIGURE a LONG BOSS ( 5/3 ) FIGURE * 0 * TO SHIM BOSS HEIGHT, ADD WASHERS AND OR SPACER(S) AT THESE LOCATIONS IF ADJUSENT IS NECESSARY. * 4 5 VINTAGE AIR PROVIDES (0) ADDITIONAL WASHERS, (3) ADDITIONAL /4 SPACERS AND () ADDITIONAL / SPACER TO ADJUST BOSS HEIGHT REV C 5//4 INSTRUCTIONS, BRACKET KIT 600, PG 5 OF 9 * SHORT BOSS EX. ( 9/6 )

6 B MOUNT INSTALLATION FOR 350, 36, 33, 400 MOPAR THIS BRACKET IS DESIGNED FOR MOPAR VEHICLES WITH POWER STEERING. INSTALL BRACKET AS SHOWN IN FIGURE 3, BELOW. OEM EAR BUSHING MUST BE ¾ LONG. IF TOP REAR EAR BUSHING IS LONGER THAN ¾, IT WILL BE NECESSARY TO TRIM THE BUSHING TO ENSURE THE BOLT WILL THREAD INTO THE ENGINE BLOCK. SEE FIGURE 3, BELOW. BRACKET RB MOUNT B MOUNT EAR 3 BB MOPAR REAR BRKT BB MOPAR FRONT BRKT FIGURE REV C 5//4 INSTRUCTIONS, BRACKET KIT 600, PG 6 OF 9 6

7 RB MOUNT INSTALLATION FOR 43, 46, 440 MOPAR THIS BRACKET IS DESIGNED FOR MOPAR VEHICLES WITH POWER STEERING. INSTALL BRACKET AS SHOWN IN FIGURE 4, BELOW. OEM EAR BUSHING MUST BE ¾ LONG. IF TOP REAR EAR BUSHING IS LONGER THAN ¾, IT WILL BE NECESSARY TO TRIM THE BUSHING TO ENSURE THE BOLT WILL THREAD INTO THE ENGINE BLOCK. SEE FIGURE 4, BELOW. RB MOUNT BRACKET OPTIONAL: AREA OUTSIDE DASH MARKS CAN BE REMOVED FOR RB APPLCATIONS B MOUNT EAR 3 5 BB MOPAR REAR BRKT BB MOPAR FRONT BRKT FIGURE REV C 5//4 INSTRUCTIONS, BRACKET KIT 600, PG 7 OF 9

8 B/RB MOPAR BELT ROUTING VINTAGE AIR RECOMMENDED BELT LENGTHS ARE 56 AND 47 ½ POWER STEERING. COMPRESSOR WATER PUMP SAGINAW POWER STEERING PUMP 9000 REV C 5//4 INSTRUCTIONS, BRACKET KIT 600, PG OF 9

9

10 MOPAR B/RB COMPRESSOR/ PACKING LIST No. QTY. PART No. DESCRIPTION BRACKET KIT 600 CHECKLIST BB MOPAR FRONT COMPRESSOR BRACKET BB MOPAR REAR COMPRESSOR BRACKET BB MOPAR FRONT BRACKET BB MOPAR REAR BRACKET MOPAR COMPRESSOR/ HARDWARE KIT CHECKED BY: PACKED BY: DATE: REV C 5//4 INSTRUCTIONS, BRACKET KIT 600, PG 9 OF 9