How To Make A Desktop

Transcription

1 Modular desks with continuous desktop appearance 1

2 Circulation Desks General Specifications DESKTOP Standard desktops are 1-3 / 16" thick, 3-ply, 45# density, particleboard core, with a top surface of.050" thick, high-pressure plastic laminate, with a backing sheet not less than.020" thickness for balanced construction. Plastic laminate has a lo-glare finish resistant to scratches, fading, and staining that meets or exceeds NEMA standards. Top receives a 5 8" x " thick, solid Northern-grown red oak edge band on the patron side with edges radiused 7 /8" to form a bullnose shape. A 1 4" thick, solid Northern-grown red oak edge band is applied to the remaining three sides, with top and bottom edges radiused. All edges are applied to the desktop after the top and bottom laminate sheets are applied, constituting an external edge band. Desktop is positioned over the end panels of the desk module, flush with the outside edges of the end panels. END PANELS Desk module end panels are 1" thick, 3-ply, 45# density particleboard core with select plain-sliced oak veneer on both sides. Exposed edges are externally banded with a 1-3 /8" x 1.6mm thick, solid Northern-grown oak edge band. The end panels and front panel are joined and secured with 3 /4" x 3 /4" thick solid hardwood cleats screwed to the inside surfaces of the panels. The bottom of each end panel receives two adjustable glides to allow leveling of the individual units. Each end panel receives a 3" diameter egress and grommet to provide for wire passage. FRONT PANELS The front panel is 3 /4" thick, comprised of select plain-sliced face veneers of Northern-grown red oak over a 45# density particle board core. Exposed edges are externally banded with a 1" x 1.6mm thick, solid Northern-grown oak edge band. The front incorporates a 6" H x 3 /4" D recessed, ebonized, toe space at the bottom of the panel. The front panel is positioned over the end panels of the desk module, flush with the outside edges of the end panels. Double wide units have two front panels to give the appearance of two individual units. WORK SURFACE Work surfaces are 1-3 /16" thick, 3-ply particleboard core, including a top surface of.050" thick, high-pressure laminate with a backing sheet not less than.020" thickness for balanced construction. Plastic laminate has a lo-glare finish resistant to scratches, fading, and staining that meets or exceeds NEMA standards. The exposed edge receives a 1 /4" thick, solid Northern-grown red oak internal edge band in straight design. The back edge of the work surface has a black strip, 1-1 2" W, which projects above the work surface 1 /4" to act as a retainer. The work surface is " D and is positioned 1-1 /2" away from the front panel, creating a cord drop space. Adjustable work surfaces are available in single wide standing height desks. Work surfaces in standing-height desks (catalog number ) may be positioned at heights of 36", 32" or 27". Note: See Brodart optional electrical accessories for electrical power-distribution system for desk modules. SHELVES Shelves are constructed of 7-ply, furniture-grade hardwood veneer-core plywood, with plain sliced solid-oak face veneer. Exposed edges receive a 1.6mm thick, solid-oak edge band. DRAWERS Drawers are constructed of solid hardwood with 1 /4" thick wood bottom panel. Drawers have 3-ply particleboard fronts with select oak-face veneer. Box drawers have extension slides with 100# load capacity. File drawers have full-extension slides with 100# load capacity. DESK DIMENSIONS -Height Desk, overall: " H x 35" W x 30" D or 39" H x 70" W x 30" D. -Height Desk, overall: " H x 35" W x 30" D or 32" H x 70" W x 30" D. 2

3 Circulation Desks Maxim Charge Desk Catalog No. Description Height Width Depth Weight (lbs.) S00 Inside dimensions are 33" W x " 35" 30" " D. The work surface is at 39-1 / 4" H. Two 3" diameter Desk without Patron Ledge 73-E14-S00 Inside dimensions are 33" W x " 35" 30" " D. The work surface is at 32-1 / 4" H. Two 3" diameter S00 Inside dimensions are 68" W x " 70" 30" " D. The work surface is at 39-1 / 4" H. Two 3" diameter Desk without Patron Ledge 73-E13-S00 Inside dimensions are 68" W x " 70" 30" " D. The work surface is at 32-1 / 4" H. Two 3" diameter S00 Inside dimensions are 33" W x " 35" 30" " D. The 7-7 8" D patron ledge is at a height of 39-1 /4". Desk with Patron Ledge and Adjustable Work Surface Note: Adjustable-height work surface may be positioned at heights of 36", 32" or 27". 73-E12-S00 Inside dimensions are 33" W x " 35" 30" " D. Patron ledge is at 32-1 /4" H. Work surface is fixed at 27" H. 3

4 Circulation Desks Desk Module with Patron-Service Ledge Catalog No. Description Height Width Depth Weight (lbs.) S00 Inside dimensions are 68" W x " 70" 30" " D. The 7-7 8" D patron ledge is at a height of 39-3 / 16". Work surface is at 35" H. Two 3" diameter grommets are located in the Note: -height roll unders do not work with this unit. 73-E11-S00 Inside dimensions are " W x " 70" 30" " D. Patron ledge is at 32-3 /16" H. Work surface is at 28" H. Two 3" diameter grommets are located in the ADA-Patron Transaction Station 73-E32-S00 The ADA transaction station is " 35" 39" 185 designed to provide wheelchair access on the patrons' side. The work surface is at 32-3 /16" H and is 35" W. The knee space depth on the patrons side is 22-1 /4" and on the staff side is 16". Two 3" diameter grommets are located in the One 3-1 / 2" diameter egress with sleeve is located in each end panel for wire passage. Open Shelf Unit S00 This unit has a full-depth fixed base " 35" 30" 175 shelf and two full-depth adjustable shelves. Two 3" diameter grommets are located in the 73-E74-S00 This unit has a full-depth fixed base " 35" 30" 155 shelf and one full-depth adjustable shelf. Two 3" diameter grommets are located in the Cupboard Unit S00 This unit has a full-depth fixed base " 35" 30" 200 shelf and two full-depth adjustable shelves. Hinged doors have a catch, lock and door pulls. Two 3" diameter grommets are located in the 73-E76-S00 This unit has a full-depth fixed base 32 3 /16" 35" 30" 180 shelf and one full-depth adjustable shelf. Hinged doors have a catch, lock and door pulls. Two 3" diameter grommets are located in the 4

5 Circulation Desks Maxim Charge Desk Catalog No. Description Height Width Depth Weight (lbs.) S00 Inside dimensions are 33" W x " D " 35" 30" 135 The work surface is at 39-1 /4" H. Unit has a 5" H x 12" W finished opening centered in the front panel for passage of books and a book chute to direct the books over a mobile depressible book truck. (Depressible book truck, Cat. No , not included). Two 3" diameter Book Return Desk 73-E15-S00 Inside dimensions are 33" W x " D " 35" 30" 120 The work surface is at 32-1 /4" H. Unit has a 5" H x 12" W finished opening centered in the front panel for passage of books and a book chute to direct the books over a mobile depressible book truck. (Depressible book truck, Cat. No , not included). Two 3" diameter S00 These units have a full-width well with " 35" 30" 165 eight removable wood trays for 5" H x 3" W cards. Discharge Unit Note: -height roll unders do not work with this unit. 73-E72-S00 These units have a full-width well with " 35" 30" 145 eight removable wood trays for 5" H x 3" W cards S00 This unit has one locking box drawer " 35" 30" 225 and two file drawers. Cupboard section has two adjustable shelves and locking door on hinges. Two 3" diameter Drawer and Cupboard Unit 73-E23-S00 This unit has one locking file drawer " 35" 30" 205 and one file drawer. Cupboard section has one adjustable shelf and locking door on hinges. Two 3" diameter 5

6 Circulation Desks Desk with Full-Width Drawer Catalog No. Description Height Width Depth Weight (lbs.) S00 This drawer unit has a full-width " 35" 30" 160 drawer 10" H x 33" W x 18-3 /4" D. Two 3" diameter grommets are located in the Note: Available in 39-3 /16" H only. Open-Shelf Unit with Drawer S00 This unit has a full-width drawer 10" " 35" 30" 180 H x 33" W x 18-3 /4" D. Also, one fixed and two adjustable, full-depth shelves. Two 3" diameter grommets are located in the 73-E34-S00 This unit has a full-width drawer 10" " 35" 30" 165 H x 33" W x 18-3 /4" D. Also, one fixed and one adjustable, full-depth shelf. Two 3" diameter grommets are located in the Cupboard Unit with Drawer S00 This unit has a full-width drawer 10" " 35" 30" 220 H x 33" W x 18-3 /4" D. Also, one fixed and one adjustable, full-depth shelf. Hinged doors have a catch, lock and door pulls. Two 3" diameter grommets are located in the Note: Available in 39-3 /16" H only. 6

7 Circulation Desks Maxim Charge Desk Catalog No. Description Height Width Depth Weight (lbs.) S00 This unit has one full-width " 35" 30" 225 drawer, two file drawers, and a lockable disc drive storage compartment. Two 3" diameter Disc Drive Storage and Drawer Unit Note: Available in 39-3 /16" H only S00 This unit has one fixed and two " 35" 30" 175 adjustable shelves. A hidden lockable disc storage drawer is positioned above the lockable disc drive storage compartment. Two 3" diameter grommets are located in the Disc Drive and Open Shelf Unit 73-E21-S00 This unit has one fixed and one " 35" 30" 160 adjustable shelf and a locking disc drive storage compartment. Two 3" diameter grommets are located in the S00 This unit has one lockable box " 35" 30" 200 drawer and two file drawers. Shelf section has two adjustable shelves, and one fixed base shelf. Two 3" diameter grommets are located in the Drawer and Open Shelf Unit 73-E24-S00 This unit has one box drawer and " 35" 30" 180 one file drawer. Shelf section has one adjustable shelf, and one fixed base shelf. Two 3" diameter 7

8 Circulation Desks Description Desk Module Multipurpose Corner Unit with Patron-Service Ledge Catalog No. Height Width Depth Weight (lbs.) S00 Unit has 29-5 /16" W port area for " 71 3 /4" 30" 245 use of one of the many optional accessory pieces of equipment. The 7-7 8" D patron ledge is at a height of 39-3 /16". Work surface is at 35" H. Storage shelves are located in the two angled areas to the left and right of the desk module. One 3" diameter grommet is located in the work surface top. One 3-1 2" diameter egress with sleeve is located in each end panel for wire passage. 73-E17-S00 Specifications are the same as " 71 3 /4" 30" 210 above, except 32-3 /16" H. Desk Module Multipurpose Corner Unit without Patron-Service Ledge S00 Unit has 29-5 /16" W port area for " 71 3 /4" 30" 250 use of one of the many optional accessory pieces of equipment. Storage shelves are located in the two angled areas to the left and right of the desk module. One 3" diameter grommet is located in the work-surface top. One 3-1 2" diameter egress with sleeve is located in each end panel for wire passage. 73-E10-S00 Specifications are the same as " 71 3 /4" 30" 215 above, except 32-3 /16" H. 8

9 Circulation Desks Maxim Charge Desk 73-E40-S00 Specifications are the same as above, " 70 1 /8" 30" 210 except patron ledge is at 32-3 /16" H. The work surface is at 28" H. Catalog No. Description Height Width Depth Weight (lbs.) S00 The 7-7 8" D patron ledge is at a height of 39-3 /16". The work surface is at 35" " 70 1 /8" 30" 245 Desk Module Curved 90 Multipurpose Corner Unit with Patron-Service Ledge H. Unit has 26-5 / 8" W port area. Storage shelves are located in the two angled areas to the left and right of the desk module. One 3" diameter grommet is located in the work surface top. One 3-1 2" diameter egress with sleeve is located in each end panel for wire passage S00 Work surface is at 39-3 /16" H. Unit has " 70 1 /8" 30" /8" W port area. Storage shelves are located in the two angled areas to the left and right of the desk module. One 3" diameter grommets are located in the work-surface top. One 3-1 2" diameter egress with sleeve is located in each end panel for wire passage. Desk Module Curved 90 Multipurpose Corner Unit without Patron-Service Ledge 73-E41-S00 Specifications are the same as above, " 70 1 /8" 30" 210 except 32-3 /16" H. 9

10 Circulation Desks Desk Module Nu-Curv 60 Corner Unit with Patron-Service Ledge Catalog No. Description Height Width Depth Weight (lbs.) S00 The 7-7 8" D patron ledge is at a " 80 3 /4" 30" 245 height of 39-3 /16". The work surface is at 35-7 /16" H. Unit has " W port area. Storage shelves are located in the two angled areas to the left and right of the desk module. One 3" diameter grommet is located in the work surface top. One 3-1 2" diameter egress with sleeve is located in each end panel for wire passage. 73-E47-S00 Specifications are the same as " 80 3 /4" 30" 210 above, except patron ledge is at 32-3 / 16" H. The work surface is at 28" H. Desk Module Nu-Curv 60 Corner Unit without Patron-Service Ledge S00 Work surface is at 39-3 /16" H. Unit " 80 3 /4" 30" 245 has " W port area. Storage shelves are located in the two angled areas to the left and right of the desk module. One 3" diameter grommet is located in the work surface top. One 3-1 2" diameter egress with sleeve is located in each end panel for wire passage. 73-E48-S00 Specifications are the same as " 80 3 /4" 30" 210 above, except 32-3 /16" H. 10

11 Circulation Desks Maxim Charge Desk Catalog No. Description Height Width Depth Weight (lbs.) S00 Inside dimensions are 33" W x " 35" 30" /4" D. The work surface is at 39-3 /16" H. Desk has locking drawer with a coin and currency tray. Two 3" diameter grommets are located in the Desk with Cash Drawer without Patron Ledge 73-E31-S00 Inside dimensions are 33" W x " 35" 30" /4" D. The work surface is at 32-3 /16" H. Desk has locking drawer with a coin and currency tray. Two 3" diameter grommets are located in the S00 This 90 unit is used to form a " 30" 140 right-angle turn in a desk arrangement. This unit is provided with a curved front panel. 90 Closed Corner Unit 73-E55-S00 This 90 unit is used to form a " 30" 120 right-angle turn in a desk arrangement. This unit is provided with a curved front panel S00 This 90 unit is used to form a right " 30" 140 angle turn in a desk arrangement. This is not available with patron ledge. One 3-1 /2" diameter egress is located in each end panel for wire passage through a continuous ABS tube. Desk Module Corner Unit 73-E16-S00 Specifications are the same as " 30" 120 above, except 32-3 /16" H S00 This square corner unit is used to " 30" 30" 160 form a right angle in a desk arrangement. One 3" diameter egress is located in each end panel for wire passage through a continuous ABS tube. Square Corner Unit 73-E50-S00 Specifications are the same as " 30" 30" 140 above, except 32-3 /16" H. 11

12 Circulation Desks 45 Closed Corner Unit Catalog No. Description Height Width Depth Weight (lbs.) S00 This corner unit is used to create a 39 3 /16" 22 7 /8" 30" angle in the circulation desk. This unit is not available with a patron ledge. 73-E18-S00 This corner unit is used to create a " 22 7 /8" 30" angle in the circulation desk. This unit is not available with a patron ledge. 45 Curved Corner Unit S00 This unit is used to create a /16" 22 3 /8" 30" 185 angle in the circulation desk. It is not available with patron ledge. 73-E58-S00 Specifications are the same as " 22 3 /8" 30" 185 above, except work surface is at 32-3 /16" H. Desk Module Computer Workstation with Recessed Monitor Shelf S00 Monitor viewing surface is at " " 35" 30" 165 H. Pullout keyboard ledge is at 35" H. A monitor shelf, which positions monitor for viewing, is mounted below the glass viewing surface. Glass insert, located in the monitor viewing surface, provides a 16" square window for viewing the monitor. The glass insert is 1 /4" thick, tempered glass, flush mounted into the monitor viewing surface. Inside dimensions are 33" W x 25" D. One 3-1 2" diameter egress with sleeve is located in each end panel for wire passage. 73-E44-S00 Specifications are the same as " 35" 30" 165 above, except monitor viewing surface is at 32-3 /16" H, and pullout keyboard ledge is at 28" H. 12

13 Circulation Desks Maxim Charge Desk Catalog No. Description Height Width Depth Weight (lbs.) S00 This 90 unit is used to form a " 30" 140 right-angle turn in a desk arrangement. Has one fixed base shelf and two adjustable shelves. 90 Open Corner Unit 73-E43-S00 This 90 unit is used to form a " 30" 120 right-angle turn in a desk arrangement. Has one fixed base shelf and one adjustable shelf. Note: Electrical pass-through is not available on open corner units. 73-E37-S00 Inside dimensions are 68" W x 26-3 /4" D " 70" 30" 260 This unit has two drawer pedestals, one mounted on each side consisting of one locking drawer at top; one file drawer with Pendaflex hangers at bottom. Two center drawers with pencil/convenience tray are mounted in the middle between the two pedestals. Two 3" diameter grommets are located in the Work Desk Note: Available in 32-3 /16" H only S00 Inside dimensions are 68" W x 26-3 /4" D " 70" 30" 250 This unit has one drawer pedestal mounted on the left side consisting of one locking drawer at top; two file drawers with Pendaflex hangers at the bottom. Two 3" diameter Single Pedestal Work Desk 73-E38-S00 Inside dimensions are 68" W x 26-3 /4" D " 70" 30" 215 This unit has one drawer pedestal mounted on the left side consisting of one locking file drawer at top; one file drawer at the bottom, both with Pendaflex hangers. Two 3" diameter 13

14 Accessories Detachable End Panels Catalog No. Description Height Width Depth Weight (lbs.) S00 End panels are 1" thick, 3-ply, 45# 37 1 /2" 26 3 /4" 1" 26 density particleboard core with 73-E78-S00 plain-sliced oak veneers. Exposed 30 1 /2" 26 3 /4" 1" 21 edges are externally banded with 1.5mm thick, solid Northern-grown oak edge band. Gate Single Action S00 For 39" H unit 33 1 /2" 36" 1" E92-S00 For 32" H unit 26 1 /2" 36" 1" 40 Double Action S00 For 39" H unit 33 1 /2" 36" 1" E93-S00 For 32" H unit 26 1 /2" 36" 1" 40 Gate is edge-banded oak, veneerfaced plywood, made to fit a space up to 36" W. Gate is attached to a mounting strip with two heavy-duty spring-loaded hinges. Single-action gates are supplied with door stop molding strip. Depressible Book Receiving Truck S00 The Depressible Book Receiving 30 3 /4" 26 1 /8" 22" 100 Truck fits under 39" H circulation desk. Construction is of 1" edge-banded veneered particleboard in flush-panel design. The depressible platform is plastic laminate and mounted on a spring mechanism, and has nylon rollers mounted on each of the four edges for ease of operation and stability. The truck is supplied with four, heavy-duty, 3" swivel casters mounted to solid hardwood caster blocks. The unit holds approximately 70 averagesize books S02 With rubber bumpers /4" 26 1 /8" 22" S00 For 32" H unit /4" 26 1 /8" 22" S02 For 32" H unit with rubber bumpers /4" 26 1 /8" 22" 90 14

15 Accessories Maxim Charge Desk Catalog No. Description Height Width Depth Weight (lbs.) Consists of all-metal construction with molded black plastic shelf. Shelf size is 22" W x 10" D. Allows keyboard to move forward, backward, 3 3 /4" 22" 10" 13 Articulating Keyboard Pullout or Optional Swing-A-Mouse up and down. Also, shelf may be tilted up to 15. Positions are all lockable Optional Swing-A-Mouse. 1 /2" " " 2 Optional Swing-A-Mouse TO-025-S00 Drawer body inside dimensions are 2-7 /8" H x 3 1 /8" 26 3 /4" 20 3 /4" " W x " D. The drawer is hung to the underside of the work surface with screws. Drawer includes a pencil/convenience tray. Knee Space Hang-A-Drawer T0-025-S02 Drawer with lock 3 1 /8" 26 3 /4" 20 3 /4" S00 Unit is made to store under the desk work 21 7 /8" 20 1 /2" 21 3 /4" 50 surface. Inside unit is a solid base with shelf and one adjustable paper-storage shelf. Usable top surface measures 19" W x 18" D. Top has two movable panels which allow the 12" W paper slot to be positioned for front, center or rear paper feed. The back of the unit has an excess-cable storage box with bottom cord egress. Front of the unit has one door on hidden hinges with horizontally placed hand pull. Stand is 21-7 /8" H. Mobile Printer Stand S00 Consists of vacuum-formed ABS plastic tray. 3 3 /4" 24 1 /2" 15" 15 Drawer slides are epoxy coated steel that have a 100# weight capacity. Shelf slides in for storage and allows the use of most standard-type computer keyboards. Basic Keyboard Pullout 15

16 Accessories Description Mobile Pedestal Open Shelf/ Computer Equipment Housing Unit Catalog No. Height Width Depth Weight (lbs.) TO-019-S00 Has two adjustable shelves and one 33" 25" " 115 base shelf. Four 3" diameter holes in the back panel allow for cord egress if computer equipment is set on the shelves. Inside dimensions: 30" H x " W x " D. Unit has four locking casters. TO-E19-S00 Has one adjustable shelf and one base " 25" " 100 shelf. Two 3" diameter holes in the back panel allow for cord egress if computer equipment is set on the shelves. Inside dimensions: 20" H x " W x " D. Unit has four locking casters. Mobile Pedestal Cupboard Unit TO-020-S00 Has two adjustable shelves and one base 33" 25" " 120 shelf. Inside dimensions: 30" H x " W x " D. Unit has two doors with concealed hinges. The cabinet is provided with a lock and two black door pulls. Unit has four locking casters. TO-E20-S00 Has one adjustable shelf and one base " 25" " 105 shelf. Inside dimensions: 20" H x " W x " D. Unit has two doors which use concealed hinges. The cabinet is provided with a lock and two black door pulls. Unit has four locking casters. Mobile Pedestal Drawer Unit TO-021-S00 Unit has locking box drawer at the top 33" " " 170 (drawer front " H) and two letter file drawers at the bottom (drawer front 12-5 / 8" H). Pendaflex file hanger is provided. Drawer bodies outside dimensions: " W x 18" D. Inside dimensions are " W x 17" D. Unit has four locking casters and each drawer has a black pull. TO-E21-S00 Unit has locking box drawer at the top " " " 150 (drawer front " H) and one letter file drawer at the bottom (drawer front 12-5 / 8" H). Pendaflex file hanger is provided. Drawer bodies outside dimensions are " W x 18" D. Inside dimensions: " W x 17" D. Unit has four locking casters and each drawer has a black pull. Full-extension, ball-bearing drawer slides, with 50# load capacity is supplied on each box drawer. File drawers have full-extension, progressive-action, ball-bearing drawer slides, with a 100# load capacity. Bottom file drawer receives a 2" diameter, black plastic, dual-wheel support caster, mounted to the underside of the drawer, positioned at center, behind the drawer front. 16