REPAIR GUIDE ALL BEAUFLOR PRODUCTS
|
|
- Josephine Jenkins
- 7 years ago
- Views:
Transcription
1
2 REPAIR GUIDE For ALL BEAUFLOR PRODUCTS Click Here Click Here Click Here Loose lay Loose lay - Insert / Patch Repair Full Glue Down - Insert / Patch Repair Cut / Slice Repair Press Esc at any time to end
3 REPAIR GUIDE For ALL BEAUFLOR PRODUCTS Click Here Click Here Click Here Loose lay Loose lay - Insert / Patch Repair Full Glue Down - Insert / Patch Repair Cut / Slice Repair Press Esc at any time to end
4 INSERT / PATCH REPAIR Damaged area of floor PROCEDURE for LOOSE LAY FLOORING INSTALLATIONS
5 Tools Needed Razor knife Straight edge Double sided carpet tape Seam bond adhesive Acrylic emulsion adhesive 1/32 x1/16 x1/16 x1/32 x1/32 Notched Spreader
6 Select a piece of material that provides a shade and pattern match Final Insert / Patch size Cut an insert piece that is at least 1 1 inch larger on each side than the material being replaced.
7 Surround the area to be repaired with double sided tape Damaged area to be replaced Position the tape where cuts will be made. Cuts should be made in grout lines or areas where the flooring pattern will camouflage patch edges.
8 Align and secure the Insert / piece Insert piece held in place with double sided tape Align the pattern of the insert piece with the surrounding flooring pattern. Secure the insert piece over the existing area to be repaired with the double sided tape.
9 Double-cut through the Insert Piece and the original flooring Use a straight edge to insure cuts remain straight. Keep the knife perpendicular to the material being cut. Cut through both the insert piece and the original flooring at the same time. If a grout line is present, center the cuts in the grout line.
10 Remove both layers of the cut flooring Remove remaining scraps and tape Mark placement with a pencil Remove and mark the sub-floor and insert piece with a pencil. Remove the remaining scraps and tape from the face of the material.
11 Adhesive Application Spread adhesive Underneath all sides Of existing floor With a notched spreader, surround the cut area beneath the remaining floor with a inch band of acrylic emulsion adhesive.
12 Adhesive Application Spread a thin bed of adhesive here as shown To secure insert. Cover the entire area where the insert is to be placed with acrylic emulsion adhesive. Use a spreader with a 1/32 x 1/16 x 1/32 notch.
13 Seam Treatment Apply an 1/8 bead of resilient flooring seam bond adhesive around the entire insert perimeter.
14 Installing the Insert Carefully tuck the insert into place forcing the seam bond adhesive up into the seam.
15 Clean-up and Roll Remove all traces of excess seam bond adhesive while wet Use a clean white cloth dampened with water to remove excess adhesive from the face of the material. Roll both the insert and surrounding area with a hand roller to ensure an even spread of adhesive and a good bond.
16 Completed Insert Repair Protect repaired area from foot and rolling traffic for 12 hours. Return to repair selections menu End presentation
17 INSERT / PATCH REPAIR Damaged area of floor PROCEDURE for FULL GLUE DOWN INSTALLATIONS
18 Tools Needed Razor Knife Straight Edge Heat Gun Putty Knives Seam bond adhesive Acrylic emulsion adhesive 1/32 x1/16 x1/16 x1/32 Notched Spreader Masking & Double sided carpet Tape
19 Select a piece of material that provides a shade and pattern match Final Insert / Patch size Cut an insert piece that is at least 1 1 inch larger on each side than the material being replaced.
20 Surround the area to be repaired with double sided tape Damaged area to be replaced Position the tape where cuts will be made. Cuts should be made in grout lines or areas where the flooring pattern will camouflage patch edges.
21 Align and secure the Insert / piece Insert piece held in place with double sided tape Align the pattern of the insert piece with the surrounding flooring pattern. Secure the insert piece over the existing area to be repaired with the double sided tape.
22 Double-cut through the Insert Piece and the original flooring Use a straight edge to insure cuts remain straight. Keep the knife perpendicular to the material being cut. Cut through both the insert piece and the original flooring at the same time. If a grout line is present, center the cuts in the grout line.
23 Peel up the scrap Masking tape is used to mark insert corner Cut flooring & double sided tape scrap Remove the scrap material and the double-faced tape beneath. Note the Blue tape used to mark one corner of inset piece.
24 Heat the Damaged Piece Completely heat the area to be removed until warm to touch to soften the adhesive beneath.
25 Removal of Fully-adhered Piece After heating use a stiff putty knife to remove the damaged piece. e. The blue tape marks the same corners of both the pieces of material.
26 Adhesive Removal With a sharp scraper remove the adhesive down to a thin residue.
27 Adhesive Removal Along Seam Be certain to remove any adhesive build up Where seams will be present Carefully clean the adhesive along the seam and in the corners to prevent any seam ledging.
28 Substrate Repair Patching compound MUST Be fully cured If necessary, repair any damage to the substrate with appropriate patching compound. Allow patching compound to thoroughly cure.
29 Adhesive Application Apply an 1/8 bead of seam bond to all seams Use the notched trowel to completely coat the back of the patch with adhesive. Apply acrylic emulsion flooring adhesive to the back of the insert piece. Apply seam bond adhesive to all seam edges.
30 Installing the Insert Carefully tuck the insert into place forcing the seam bond adhesive up into the seam.
31 Clean-up and Roll Remove all traces of excess seam bond adhesive while wet Use a clean white cloth dampened with water to remove excess adhesive from the face of the material. Roll both the insert and surrounding area with a hand roller to ensure an even spread of adhesive and a good bond.
32 Completed Insert Repair Protect repaired area from foot and rolling traffic for 12 hours. Return to repair selections menu End presentation
33 CUT / SLICE Damaged area of floor REPAIR PROCEDURE
34 Application of adhesive With a small putty knife, work acrylic emulsion flooring adhesive under the material as far as possible in all directions.
35 Seam Treatment Using a clean screwdriver hold the edge of the material apart and apply seam bond adhesive.
36 Adhesive Application Remove all traces of excess seam bond adhesive while wet Excess seam bond adhesive Force the seam bond adhesive up into the seam. Clean off the Seam Bond adhesive with a clean damp white cloth.
37 Clean-up & Secure Masking tape will hold seam together while seam bond cures Roll the area around the repair using a hand roller. Use masking tape to hold the seam together while the adhesive sets
38 Completed Permanent Repair Protect repaired area from foot and rolling traffic for 12 hours. Return to repair selections menu End presentation
39 Press Esc to end Return to repair selections menu
Shower Walls and Tub Surrounds
Reverso en español TEC Skill Set How-To Project Guide Shower Walls and Tub Surrounds 3 Steps to a Beautiful Tile Surface! 1. Prepare the surface 2. Set the tile 3. Grout and caulk H.B. Fuller Construction
More informationFiberglass-Reinforced Sheet Flooring Installation System
Fiberglass-Reinforced Sheet Flooring Installation System Product Adhesive Comments Residential Use Only CushionStep Value Good Better Best FlexStep Duality Premium Premium Plus Modified loose lay method
More informationCommercial/Residential Linoleum Sheet Installation System
Commercial/Residential Linoleum Sheet Installation System COMMERCIAL USE ONLY Product MARMORETTE GRANETTE COLORETTE UNI WALTON LINORETTE Gauge 0.080" (2.0 mm) 0.100" (2.5 mm) 0.125" (3.2 mm) 0.100" (2.5
More informationFiberglass-Reinforced Sheet Flooring Installation System
RESIDENTIAL USE ONLY Fiberglass-Reinforced Sheet Flooring Installation System Product Gauge Comments FlexStep Value FlexStep Good 0.055" (1.4 mm) 0.065" (1.65 mm) Modified loose lay method: Acrylic double-faced
More informationVinyl Composition Tile Installation System
Vinyl Composition Tile Installation System Product Gauge Size Vinyl No-Wax (Dry Back) Urethane No-Wax (Dry Back) 0.045" (1.1 mm) 0.080" (2.0 mm) IMPERIAL TEXTURE 0.094" (2.4 mm) STONETEX ChromaSpin COMPANION
More informationINSTALLATION RECOMMENDATIONS. Outdoor Rubber Tiles
INSTALLATION RECOMMENDATIONS Outdoor Rubber Tiles Prior to Installation: The Outdoor Rubber Tiles and accessory transition pieces intended for this installation have been shipped to you via a freight carrier
More informationInstallation System. Existing Resilient Sheet Floors
Vinyl Composition Tile Installation System Product Adhesive/Full Spread Adhesive/Tile-On Comment Imperial Texture MultiColor RAVE Stonetex Companion Square Feature Tile/Strips ARTEFFECTS SAFETY ZONE Vinyl
More informationBlack Wolf POCKET BILLIARD TABLE INSTALLATION MANUAL. SERVICE DEPARTMENT P.O. BOX 68 BRISTOL, WI 53104
Black Wolf TM POCKET BILLIARD TABLE INSTALLATION MANUAL www.brunswickbilliards.com SERVICE DEPARTMENT P.O. BOX 68 BRISTOL, WI 53104 51-905710-000 SEPTEMBER 2010 NOTE: Please use the instructions in this
More informationThe Mohawk Group Installation Guidelines for
The Mohawk Group Installation Guidelines for Uniplus System II Double Stick Unibond RE Wet Set The Mohawk Group 1975 West Oak Circle Marietta, GA 30062 800-554-6637 www.themohawkgroup.com Field Services
More informationAdhesive Recommendation for Altro Flooring. Porous (absorbent) subfloors (most wood subfloors and some concrete)
Adhesive Recommendation for Altro Flooring Product Safety Sheet Flooring Smooth Sheet Flooring Porous (absorbent) subfloors (most wood subfloors and some concrete) Altrofix 30/31 (excessively heavy rolling
More informationArmstrong Do-It-Yourself Tile Installation System
Armstrong Do-It-Yourself Tile Installation System What tools will I need to install my tile floor? You'll need just the basics: - floor tile (make sure you have enough tile to finish the job) - adhesive
More informationDIY CABINET REFACING INSTALLATION GUIDE
DIY CABINET REFACING INSTALLATION GUIDE CABINET REFACING INSTALLATION Are you ready to reface your outdated cabinets? This guide will show you how to install your new Facelifters Cabinet Refacing Products
More informationYour guide to home maintenance. Flat Roofs
Your guide to home maintenance Flat Roofs Your guide to home maintenance is a series of information leaflets that gives you all the information you need to keep your home in tiptop condition. Flat Roofs
More informationAsbestos Work Permit Procedures
These procedures are to be followed by all persons required to perform the following work: Handling, installation or removal of non-friable manufactured products known to contain asbestos provided no sanding,
More informationINSTALLATION INSTRUCTIONS FOR RIGID VINYL WALLCOVERING
INSTALLATION INSTRUCTIONS FOR RIGID VINYL WALLCOVERING HIGH IMPACT, PROTECTIVE, STAIN-RESISTANT RIGID VINYL WALLCOVERING SHEETS FOR: HEALTHCARE/ELDERCARE FACILITIES LODGING & HOSPITALITY RETAIL ESTABLISHMENTS
More informationFAQs. 19. Does the sub floor need to be level before I install my new direct-to-stud bathtub or shower base?
1. Where is the serial number of my tub located? 2. What can I use to clean my tub or shower? 3. What is an Above Floor Rough-in? 4. Can I replace my towel bar? 5. What are grommets? 6. Why do some bathing
More informationBella Cera Engineered Hardwood Flooring Installation Instructions. Check for Proper Color Selection Prior to Installation
Bella Cera Engineered Hardwood Flooring Installation Instructions Check for Proper Color Selection Prior to Installation 1 Important Information before You Begin 1.1 Installer/Owner Responsibility Carefully
More informationBENTLEY ELEMENTS COLLECTION LVT
This document refers to the following products: Product Size Installation direction Seams treatment Elements Tiles See specifications 90 None Elements Planks See specifications Stair Step None Note: This
More informationCarpet Tile Installation Guidelines
NOTICE FAILURE TO FOLLOW THESE GUIDELINES CAN RESULT IN VOIDING THE CARPET WARRANTY. Installation Guidelines The following instructions should be reviewed prior to installation. Shaw Industries will not
More informationHow to Install GoBoard:
How to Install GoBoard: A Step-by-Step Guide Durable, Ultra-Lightweight, Waterproof Tile Backer Board Introducing GoBoard Every tiling project requires a durable, waterproof surface under the tile, called
More informationLaminate Flooring T-Lock Angle-Drop Installation Instructions
TECHNICAL SERVICE Laminate Flooring T-Lock Angle-Drop Installation Instructions March 23, 2012 Read all instructions carefully before beginning installation. Make sure that the instructions are the most
More informationRepairing Drywall Techniques for fixing everything from popped screws to big holes
Repairing Drywall Techniques for fixing everything from popped screws to big holes BY MYRON R. FERGUSON C racks or holes in drywall, wet or stained drywall, peeling joint tape, popped nails or screws.
More informationHerringbone Pattern Flooring
Herringbone Pattern Flooring If it s not marked NOFMA, it s not certified. Handling, Storage, Installation and Tips Herringbone is generally manufactured from 3/4 x 2 ¼ or ¾ x 1-1/2 standard tongue & groove
More information1300 West Bartlett Road Elgin, Illinois 60120-7529 Phone: (847) 741-5370 Fax: (847) 622-7077. SUBJECT: Pelican NP and NS Cab Glass Replacement
SERVICE BULLETIN Subsidiary of Federal Signal Corporation 1300 West Bartlett Road Elgin, Illinois 60120-7529 Phone: (847) 741-5370 Fax: (847) 622-7077 DATE: 08/07/2007 NUMBER: 0703146 SUBJECT: Pelican
More informationINSTALLATION INSTRUCTIONS FOR LAMINATE FLOORING
INSTALLATION INSTRUCTIONS FOR LAMINATE FLOORING Introduction Laminate flooring is designed to be a floating floor that may be installed over virtually any type of sub floor. It is not nailed or glued to
More informationBuild a Junior Solar Sprint Model Car Kit Materials: 1 PITSCO Ray Catcher Sprint Kit or Solar Made Junior Solar Sprint Kit 1 White Sheet of Plastic
Build a Junior Solar Sprint Model Car Kit Materials: 1 PITSCO Ray Catcher Sprint Kit or Solar Made Junior Solar Sprint Kit 1 White Sheet of Plastic Coated Paper 2 Balsa Sheets (10-1/2 x4 x3/16 ) 2 Alligator
More informationPRODUCT CONSTRUCTION ROLL WIDTH
products Inlaid: Fine Fields / Magna Homogenous Inlaid: BioSpec MD / Lifelines II Heterogeneous Light: Aberdeen Collection / Insight Plus Slip-Retardant Sheet: Mannington Assurance II roll widths PRODUCT
More informationAspect Metal Peel & Stick Tile Installation Guide
Aspect Metal Peel & Stick Tile Installation Guide Proper surface preparation is essential for a successful project Failure to follow recommended surface preparation instructions may void the warranty Read
More informationKemlite Transportation Products
Kemlite Transportation Products Roof Repair Manual (for use with repair kit #R50TFIX) Kemlite SunPatch Repair Kit is also available for small repairs. A Crane Co. Company This roof repair manual is copyrighted
More informationTechnical Services. Product MM INCH Installation direction Seams treatment GTI CONNECT (interlocking)
INSTALLATION INSTRUCTIONS FOR GTI CONNECT TILES This document refers to the following products: Product MM INCH Installation direction Seams treatment GTI CONNECT (interlocking) 635 X 635 mm 25.5 x 25.5
More informationQWALL 4 ACRYLIC SHOWER WALL INSTALLATION INSTRUCTIONS
QWALL 4 ACRYLIC SHOWER WALL INSTALLATION INSTRUCTIONS IMPORTANT DreamLine TM reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical
More informationFabric Replacement Top Installation Instructions
Replacement Top Installation Instructions For: Wrangler/YJ 88-95 Part Number: 51120 Special Note: If your Wrangler is a 1986 or 1987 model, this kit is not the correct product. Please order Part Number
More informationAmorim Rubber Flooring Specifications
Amorim Rubber Flooring Specifications Test Method Amorim Typical Value Durometer, Shore A, points of hardness ASTM D2240-97 60 Density, lbs/ft 3 ASTM D297-93 Part A, Section 16.3 64 Compressibility @ 100
More informationPAINT. PAINTING WALLS... 115 -Interior Walls -Exterior Walls PAINTING DOORS... 117 CLEAN UP... 118
PAINT PAINTING WALLS...... 115 -Interior Walls -Exterior Walls PAINTING DOORS... 117 CLEAN UP....... 118 112 Basic Construction Safety SAFETY TALK #1: Drink plenty of water and watch for dehydration! When
More informationBLADE REPAIR INSTRUCTION BOOKLET
BLADE REPAIR INSTRUCTION BOOKLET Contents Section I: Section II: Section III: Section IV: Section V: Section VI: Removing a Blade Refer to this section if you need to remove the blade from an oar shaft.
More informationEngineered Hardwood Flooring Installation Instructions
Engineered Hardwood Flooring Installation Instructions Tip: Check for proper color selection and style prior to Installation. No claims will be accepted after installation Important Information before
More informationVC 104+ Rigid Grade / Rigid Grade Imagine VC 104 Rigid Grade Commercial Customised
Page 1 of 6 instructions VC 104+ Rigid Grade / VC 104+ Rigid Grade Imagine / (for the rest of this document referred to as VC 104) can be applied to new and used trucks and trailers with painted rigid
More informationKnauf Aquapanel Interior. Tile Backing. Cement board for wet areas. Will not deteriorate in water. Easy to score and snap
Tile Backing Will not deteriorate in water Easy to score and snap Resistant to mould and mildew Knauf Aquapanel Interior Cement board for wet areas Knauf Aquapanel Interior Cement Board Drywall for Wet
More informationApplication Instructions for Avery Dennison Films SF100-843-S LTR EZ RS, Conform Chrome
Application Instructions for Avery Dennison Films SF100-843-S LTR EZ RS, Conform Chrome Instructional Bulletin #4.00.2 (Revision 0) Dated: 04/05/2012 1.0 Consult Product Data Bulletin Before starting application,
More informationInstallation Instructions for Fletco Carpets
Table of Contents The backing is a very important part of a carpet, as well as the installation and the daily use are concerned, so therefore these installations instructions are based on the different
More informationFloriani Embroidery Project PATCH PERFECTION
Floriani Embroidery Project PATCH PERFECTION TRADITIONAL PATCH USING A BACKGROUND FABRIC This method of patch making requires a design that will stitch a straight stitch on the fabric first to hold the
More informationENGINEERED FLOORING INSTALLATION
ENGINEERED FLOORING INSTALLATION ATTENTION! INSTALLER/OWNER RESPONSIBILITIES Beautiful hardwood floors are a product of nature and, therefore, they will show variations in color, grain, texture, and appearance.
More informationwww.cornholesupplies.com
www.cornholesupplies.com How To Build Regulation Cornhole Boards Home of the Original Cornhole Bags and Boards Supply List: 1-4' X 8' Piece of Plywood (pre sanded) 4-2" X 4" X 8' Studs (2 by 4s make sure
More informationBETON. CONCRETE EFFECT IMITATION CONCRETE FOR A PURE AND MODERN EFFECT Application instructions primer - base - finish
BETON CONCRETE EFFECT IMITATION CONCRETE FOR A PURE AND MODERN EFFECT Application instructions primer - base - finish beton PRIMER The colour of the cachemire beton Primer is white, to get the best result
More informationGARDEN WINDOW GLAZING AND DE-GLAZING INSTRUCTIONS
GARDEN WINDOW GLAZING AND DE-GLAZING INSTRUCTIONS DE-GLAZING 1.) If there is any PVC cement covering the joints where external glazing bead strips meet, cut through the cement with a utility knife. 2.)
More informationLAYING BLOCK AND BRICK
LAYING BLOCK AND BRICK Products highlighted in this section: SAKRETE Type N Mortar Mix SAKRETE Type S Mortar Mix Brick And Block Laying Basics The first step in building a brick or block wall is to construct
More informationVINYL CLICK FLOORING INSTALLATION GUIDE
VINYL CLICK FLOORING INSTALLATION GUIDE Owner/Installer Responsibility Prior to installing a single board, you or the installer must determine that the job-site environment and the sub-surfaces meet the
More informationHow to Install Hardwood Flooring Over a Sub Floor
How to Install Hardwood Flooring Over a Sub Floor Installation Preparation Instructions Read the entire instructions before starting your project. 1) INSPECT EACH PLANK (see fig. a) Wood is a natural product
More informationMapei systems for radiating floor heating with high thermal efficiency
Mapei systems for radiating floor heating with high thermal efficiency PRODUCTS FOR CERAMIC TILES AND STONE MATERIAL ADHESIVES SEALANTS CHEMICAL PRODUCTS FOR BUILDING III MAPEI systems for radiating floor
More informationad notam INSTALLATION GUIDE MONITOR ON GLASS MOUNTING SYSTEM (MGS) Art.No. MGS-xxxx
ad notam MONITOR ON GLASS MOUNTING SYSTEM (MGS) Art.No. MGS-xxxx INSTALLATION GUIDE FOR YOUR SAFETY Please read all safety information thoroughly before using the product. Not complying with the instructions
More informationDivision 9. SignaFlor Pad and Pour Flooring System
Division 9 SignaFlor Pad and Pour Flooring System SPECIFICATIONS Page 1. General... 2 1.1 Description 2 1.2 Quality Assurance 2 1.3 Submittals 2 1.4 Delivery and Storage 3 1.5 Warranty 3 1.6 Working Conditions
More informationDRAINAGE MATS For Vertical: Flow 15-P For Horizontal: Flow 18-H
DRAINAGE MATS For Vertical: Flow 15-P For Horizontal: Flow 18-H Soil Drainage Mat with Built-In Protection Layer POLYGUARD DRAINAGE MATS are three-part prefabricated geocomposite drain consisting of a
More informationEucaboard / Eucaplac/ Eucatile paneling is intended for dry interior use only and requires care in handling.
i This instruction sheet describes the proper methods for installing Eucatex decorative wall paneling. Eucaboard / Eucaplac/ Eucatile paneling is intended for dry interior use only and requires care in
More informationWINDOW REPAIR MANUAL & REFERENCE GUIDE
WINDOW REPAIR MANUAL & REFERENCE GUIDE TABLE OF CONTENTS DOUBLE HUNG & SINGLE HUNG PARTS 4-5 CASEMENT PARTS 6 SCREEN PARTS 7-8 HOW TO REMOVE TILT-IN SASH 9 HOW TO REMOVE A BALANCE 10 HOW TO INSTALL BALANCE
More informationSelf-Stick Roofing Solutions
Peel & Seal Self-Stick Roofing Solutions Ideal for Low Slope Applications Waterproof and Weatherproof Energy Efficient Tough and Durable Versatile, Effective Sealing Around Protrusions Perfect for Vents,
More informationSeven. Easy Steps. Your Own Walkway, Without Mortar. or Concrete. to Installing. Driveway and Patio
Seven Easy Steps to Installing Your Own Walkway, Driveway and Patio Without Mortar or Concrete Brick is one of the world s oldest and most enduring building materials. Those same qualities also make it
More informationHere is your set of Detailed Plans from Copyright 2004 All Rights Reserved
Here is your set of Detailed Plans from Copyright 2004 All Rights Reserved Materials for the House Here is the list of materials you will need to construct the basic house then to cover it with roofing
More informationHow to Build a Printed Circuit Board. Advanced Circuits Inc 2004
How to Build a Printed Circuit Board 1 This presentation is a work in progress. As methods and processes change it will be updated accordingly. It is intended only as an introduction to the production
More informationInstallation Systems. Chapter V Installation Systems
V Installation Systems Chapter V Installation Systems 81 ARSTRONG STRATEGIC ACCOUNTS RECOENDED SHEET FLOORING ADHESIVES AND INSTALLATION SYSTE Product Avantra Cambray Chelsea Corner Concerto Deco Collection
More informationFinding and Fixing Leaks
Finding and Fixing Leaks Where did all that water go? Could we have splashed all that water out of the tub? These are all common thoughts that can run through your mind when you open up the hot tub cover
More informationAssembly GUIDE. display wine cellar kits. Required. Suggested. Questions? 888.373.6057. or visit wineracksamerica.com
Page 1 Middle Ladder End Ladder Display Tray Screwless Connector Package Contents * All models follow the same assembly procedure varying only in the number of middle ladders your rack will require. Depending
More informationFRAMED & MOUNTED TILE MURAL
Page 1 of 5 There is no denying that tile murals have taken the sublimation industry by storm. The unique ability to take a customer s artwork or high resolution photograph, tile it using your software
More informationLadder Shelf Plans Final dimensions: 25 L x 21 W x 72 H
Ladder Shelf Plans Final dimensions: 25 L x 21 W x 72 H Copyright 2011. MLCS Woodworking. Page 1 Router bits and supplies needed: 3/8 Rabbeting bit (#10691) 1 Bottom Cleaning bit (#7941) Top and Bottom
More informationSEAMS SEAMING USING SEAM TAPE
SEAMING USING SEAM TAPE SEAMS The membrane should be positioned so that the width of the seam is 3. Remove excess chalk from a chalk line by snapping the line into the air and then chalk a line one-quarter
More informationAcrylic Walls Installation Instructions
Acrylic Walls Installation Instructions IMPORTANT Please read carefully the following instructions before installing your shower acrylic walls. If you have any questions on this shower acrylic walls installation
More informationHow to Properly Remove Sheet Vinyl Flooring with Asbestos
Asbestos Removal Procedures for Home Owners* How to Properly Remove Sheet Vinyl Flooring with Asbestos IMPORTANT: Read these procedures from start to finish, making sure you thoroughly understand them,
More informationWritten By: Walter Galan
ipad 2 GSM Front Panel Replacement Replace the front panel in your ipad 2 GSM. Written By: Walter Galan INTRODUCTION Note: this is a complete guide for replacing a plain front panel. If you have a Front
More informationJOB READY ASSESSMENT BLUEPRINT PAINTING AND DECORATING. Test Code: 2060 Version: 01
JOB READY ASSESSMENT BLUEPRINT PAINTING AND DECORATING Test Code: 2060 Version: 01 Specific Competencies and Skills Tested in this Assessment: Wood Finishes Identify thinning products Identify wood finish
More informationBuilding an Off-Center Fixture for Turning Pendants
Building an Off-Center Fixture for Turning Pendants Turning a pendant off-center with most available metal pendant chucks means that you will have a significant amount of mass off center, which will limit
More informationHYDRO BAN Sheet Membrane
HYDRO BAN Sheet Membrane DS-041.0-0315 1. PRODUCT NAME HYDRO BAN Sheet Membrane 2. MANUFACTURER LATICRETE International, Inc. 1 LATICRETE Park North Bethany, CT 06524-3423 USA Telephone: +1.203.393.0010,
More informationInstalling Window and Door Mouldings
Installing Window and Door Mouldings About Window and Door Mouldings The trim around windows and doors greatly influences the look and style of your interior. They also bridge the gaps and cover spaces
More informationWritten By: Walter Galan
ipad 2 GSM Rear Camera Replacement Replace the rear camera in your ipad 2 GSM. Written By: Walter Galan INTRODUCTION Use this guide to replace a broken rear camera. TOOLS: ifixit Opening Picks set of 6
More informationSECTION 623 CONCRETE BONDING COMPOUND, EPOXY MORTAR AND EPOXY POLYMER CONCRETE OVERLAY SECTION 623.10 CONCRETE BONDING COMPOUND.
SECTION 623 CONCRETE BONDING COMPOUND, EPOXY MORTAR AND EPOXY POLYMER CONCRETE OVERLAY SECTION 623.10 CONCRETE BONDING COMPOUND. 623.10.1 Description. This work shall consist of preparing the surface,
More informationwww.startskiwax.com Waxing guide for recreational and fitness skiers
www.startskiwax.com Waxing guide for recreational and fitness skiers Easy choice. Start Easy waxes New Start Easy waxes are easy to handle and safe to use. The Easy line consists of liquid Easy kick and
More information3D Print Link's Hylian Shield
3D Print Link's Hylian Shield Created by Ruiz Brothers Last updated on 2015-07-14 04:20:12 PM EDT Guide Contents Guide Contents Overview Parts, Tool & Supplies 3D Printing 3D Printed Parts Slicer Settings
More informationThe Jeans Collection
The Jeans Collection Video 4 - Cutting out the panels The tools that you will need to cut out your cloth: 1. Commercial jeans pattern 1. Measurement sheet 2. Tailors chalk. 3. Tape measure 4. Pattern cutting
More informationHow to Build Your Own CornHole Game
How to Build Your Own CornHole Game DIMENSIONS Here is a diagram with the basic measurements for the Cornhole board game. SUPPLIES 1/2 thick sheet of plywood one 4 x4 or two 2 x4 s 8 long 2 4 s (4) 4 1/2
More informationDUROCK Brand Cement Board. installation guide. Substrate and ceramic tile installation for walls, floors, countertops and wall shields.
DUROCK Brand Cement Board installation guide Substrate and ceramic tile installation for walls, floors, countertops and wall shields. DUROCK Brand Cement Board... Strength beneath the surface A ceramic
More informationAwanaGames Circle. Official. Diagram 1. Key to diagram: Pin & Striped Bean Bag C Diagonal or Starting Line. B Scoring Pins, or Center.
Official AwanaGames Circle Diagram 1 The AwanaGames Circle is 30 feet in diameter surrounded by a 37-40 foot square. Each team is designated by a color and occupies a quarter-circle or one side of that
More informationCOMMERCIAL RESILIENT INSTALLATION GUIDELINES
COMMERCIAL RESILIENT INSTALLATION GUIDELINES GENERAL INFORMATION All substrates to receive moisture sensitive floor covering require proper moisture testing. Use only Portland based patching and leveling
More informationDASH KIT INSTALLATION
ÿÿÿÿÿ ÿÿÿÿÿÿÿÿÿÿÿÿ ÿÿÿ ÿÿÿÿÿ ÿÿ ÿÿÿ ÿÿÿÿÿÿÿÿÿÿÿÿÿÿ ÿÿÿÿÿÿÿÿÿÿ ÿÿÿÿ ÿÿÿÿ ÿÿ ÿÿÿÿÿ ÿÿÿÿÿÿÿÿ PROUDLY MADE IN THE USA DASH KIT INSTALLATION These instructions are aimed at the do-it-yourself installer. Read
More informationTechnical Data wedi Subliner Dry Waterproofing Shower and Wet Area System
Technical Data wedi Subliner Dry Waterproofing Shower and Wet Area System Technical Data wedi Subliner Dry Waterproofing Shower and Wet Area System General Product Description Waterproof, thin-layer, crack
More informationConstruction. Sikadur-Combiflex. Sealing system for cracks and problem joints with large movements DESCRIPTION
Sikadur-Combiflex REVISED JULY 2002 Sealing system for cracks and problem joints with large movements Construction DESCRIPTION USES ADVANTAGES The Sikadur-Combiflex joint sealing system consists of two
More informationMinor Cracks in Horizontal Surfaces
Cracks, chips and broken or flaking areas in concrete are not only unsightly, they can lead to further deterioration of the surface. The result is a costly replacement project as opposed to a simple repair.
More informationGuide Specification SECTION 09 68 16 SHEET CARPETING PART 1 - GENERAL 1.1 SUMMARY. A. This Section includes broadloom carpet. 1.
SECTION 09 68 16 SHEET CARPETING PART 1 - GENERAL 1.1 SUMMARY A. This Section includes broadloom carpet. 1.2 STANDARDS A. Except as modified by governing codes and by the Contract Documents, comply with
More informationPANELIZED HOME INSTALLATION GUIDELINE
PANELIZED HOME INSTALLATION GUIDELINE A typical home package will be constructed of Snap-N-Lock Insulated Panels clad with steel skins. 4" panels will be used for the walls, and 6" panels for the roof.
More informationHow to Install Drop Ceiling Panels
How to Install Drop Ceiling Panels Both Ceilume s 0.013 thick Feather-Light and 0.030 thick Signature Ceiling Tiles can be installed in an approved ceiling suspension system using standard 15/16 face T-bar
More informationInstalling Window Trim and Door Trim
Installing Window Trim and Door Trim Tools and Supplies You'll Need Screws or Finish Nails use screws or nails that are long enough to go through the Ledger and firmly attach to the wall behind it. If
More informationNEW ELECTRICAL SUBSTATION Building 300 SECTION 07 53 23 ETHYLENE-PROPYLENE-DIENE-MONOMER ROOFING WORK
ETHYLENE-PROPYLENE-DIENE-MONOMER ROOFING WORK PART 1 GENERAL 1.1 REFERENCES The publications listed below form a part of this specification to the extent referenced. The publications are referred to within
More information738-B-297 POLYMERIC CONCRETE BRIDGE DECK OVERLAY. (Adopted 02-20-14)
POLYMERIC CONCRETE BRIDGE DECK OVERLAY (Adopted 02-20-14) Description The polymeric concrete bridge deck overlay shall consist of an epoxy polymer that acts together with special aggregate to form an overlay
More informationStainless Steel Sink Work Center With Portable Sink, Colander and Cutting Board
SKU: 463780 / QK09 Owner s Manual Stainless Steel Sink Work Center With Portable Sink, Colander and Cutting Board THANK YOU for selecting American Standard the benchmark of fine quality for over 00 years.
More informationGENERAL RUBBER LINING PRINCIPLES
GENERAL RUBBER LINING PRINCIPLES I. METAL PREREQUISITES Metal to be lined should meet the requirements as stated in section 8 Metal Fabrication and section 12 Blasting and Cementing Procedures. The surface
More informationINSTALLATION GUIDE. americanwick.com 800.242.WICK (9425)
INSTALLATION GUIDE americanwick.com 800.242.WICK (9425) American Wick Drain SITEDRAIN prefabricated drainage products may be installed in a variety of civil construction applications including: retaining
More informationChelsea Loft Bed WARNING:
Chelsea Loft Bed WARNING: Failure to follow these warnings and assembly instructions could result in serious injury or death. Read all instructions before assembling bunk bed. KEEP INSTRUCTIONS FOR FUTURE
More informationCreate a Camera Obscura
Artists in the 17 th and 18 th centuries sometimes used a tool called a camera obscura (Latin for dark room ) to make precise drawings. With a camera obscura, an artist could project an image of a scene
More informationHow to Install UnderDeck The Original.
How to Install UnderDeck The Original. TOOLS: Chalk Line Caulk Gun Garden hose or water bucket Gloves Hammer or Screw Gun Power Mitre Saw with OSB Blade Pencil Pliers Safety Glasses Straight Edge / Carpenter
More informationFree-Form Concrete Pool
The tranquil beauty and playful shimmer of a reflecting pool or fountain is just the thing to enhance the charm of your garden or patio. Best of all, you can do all the work yourself. Add goldfish or water
More informationSolvent Cementing Instructions For Plastic Pipe & Fittings
Solvent Cementing Instructions For Plastic Pipe & Fittings Description Solvent cementing is the process of fusing plastic pipe and fittings by the use of an adhesive containing a suitable active solvent
More informationWATERPROOFING OF WET ROOMS
WATERPROOFING OF WET ROOMS Waterproofing under tiles For longterm enjoyment of a wetroom area a complete and resistant waterproofing system is an important precondition. Most tiles are by themselves waterproof
More informationFREEBIRD THE ORIGINAL D.I.Y. ORNITHOPTER! Tools and Glue. Required Materials
Do not try to make your ornithopter using "household materials". If you want it to fly, you have to build it right. FREEBIRD THE ORIGINAL D.I.Y. ORNITHOPTER! Wingspan: 16 inches Weight: 1/4 ounce The Ornithopter
More information