KITCHEN CABINET AND COUNTERTOP INSTALATION
|
|
- June Griffin
- 7 years ago
- Views:
Transcription
1 KITCHEN CABINET AND COUNTERTOP INSTALATION PREPARATION: The cabinet installation is part of the Finish step of building the house. MATERIALS: Cabinet plan Cabinets/Fillers/Toe kick/countertop(s)/backsplash Square drive, Merillat or equivalent, cabinet screws (2 ½ ) Drywall screws (2 ½ ) for cabinet face frames Drywall screws (2 ) to attach countertop to cabinets 3- packs of shims Hood Vent fan cut out template Kitchen sink cut out template Bathroom sink cut out template Wood glue (to assemble counter top) Sub floor adhesive and large caulk gun (to attach backsplash/toekick) Countertop matching caulk and caulk gun for backsplash At least 2 people will be needed to complete the installation. A 3rd person may be needed and should be available from the door hanging crew. In addition you will need: Special Kitchen Cabinet Clamps or speed clamps Cordless drill(s) Drill bits 1/8, 7/32 and a countersink 1 paddle style drill bit for water supply line holes 3 hole saw for water drain lines Stud Finder may be helpful to verify blocking or locate studs if blocking is suspect. Levels (2, 4 and 6 ) Mitre saw (probably on site with door hanging and trim activity) Jig saw ( ) Using the plan, take an inventory of the cabinets, including the bathroom vanity. Do a quality check to make sure none of the cabinets are damaged.you will be starting with the upper cabinets, so if the base cabinets are missing or damaged, you have time to get them to the site. Some installation may include an additional vanity, counter top and backsplashes for the Basement Bath. Thoroughly sweep the floor area, making sure all drywall mud etc is removed. Separate the cabinets with the wall units being closest to kitchen.
2 STEP 1: Locate the high point of the kitchen floor, along the outside walls, with a 6 level and or a long, straight 2 x 4 and a level. Using the highest point found, mark a level line on the 3 kitchen walls at the height of the base cabinets 34 ½, UNLESS GIVEN ANOTHER NUMBER BY THE HOUSE LEADER OR HFH STAFF. Set a 2nd mark at 54 up from the high point and mark a level line on the 3 kitchen walls. This will be the BOTTOM of the full height upper cabinets. Mark these lines just dark enough to be seen. Using the cabinet plan, you will see the cabinet over the stove and refrigerator will be higher up the wall. Using the plan, do a rough layout, marking the cabinet locations, sizes and hinge orientation on the wall, ABOVE the 54 mark and BELOW the 34 ½ mark. NEXT, verify the location of cabinet blocking behind the drywall. Standard locations are: 80 ½ - 84 off the floor ½ off the floor. # /2 off the floor ½ off the floor also for bath vanity # Note: Blocking is at this height, so a ledger can be attached to support the upper cabinets during installation. If blocking is not set at correct height, wall studs will have to be located. They are marked on the floor with orange paint or can be found on either side of the electrical outlets. Use and 8d nail, between the edge of the electrical box and drywall, to verify which side the stud is on. Cabinet blocking specifications for Handicap applications are in the section covering Kitchen Cabinet Blocking. WALL CABINETS: Start the installation with WALL cabinets in the LEFT corner, facing the street. Attach a ledger board, usually a piece of door casing which is in the house for the door install, at the 54 line on the garage wall and front wall of the house, with drywall screws. CRITICAL: USE ONLY SPECIALTY CABINET SCREWS, NOT DRYWALL SCREWS, TO ATTACH CABINETS TO THE WALLS. Single door wall cabinets can be turned over to change from Right to Left hand hinge. REMEMBER to turn the shelf support brackets over when replacing the shelves.
3 START THE INSTALL: Place the Wall Corner 2430 cabinet and a W1230, per the plan, on the floor. Mark the hinge location on the cabinet with a PENCIL and remove the doors. CHECK SHELF SUPPORTS TO ENSURE CABINET IS RIGHT SIDE UP AND THE HINGE IS ON THE CORRECT SIDE. Attach the cabinets through the face frames, with 3 evenly spaced 2 ½ drywall screws, 1 ea. above and below the hinges and 1 in the middle. Align the face frames and clamp cabinets together. Drill the initial hole through both face frames, with a 1/8 drill bit. Enlarge the hole, IN THE FIRST CABINET ONLY, with a 3/16 drill bit so the screw will not bind going through the cabinet. Counter sink the hole, so the screw sits flush to the face frame. WITH BLOCKING: Pre- drill TOP holes in upper cabinets, 1 down from the inside top of the cabinet, with a 7/32 bit. WITHOUT BLOCKING: LAYOUT FOR WALLS STUDS BEFORE DRILLING. Lift the assembly on to the ledger, tight against the FRONT/SIDE walls. Temporarily attach the cabinets to the wall in the top holes. Check for level and plumb on all sides of cabinets. Shim as needed and attach permanently with 4 CABINET screws on the top and bottom. Moving down the garage wall, the next cabinet is a W It will need the BACK cutout for the vent in the wall and possibly an electrical outlet. Position the cabinet on the wall, ABOVE THE VENT ROUGH IN, mark the vent location on the Bottom of the cabinet. Remove the cabinet and extend lines down rear of cabinet. Complete the layout, drill starter holes and cut with a jig saw. The bottom of the cabinet will also be cut out for the Stove Hood Vent, using an onsite TEMPLATE. Place the template in side the bottom frame, mark the vent opening, drill starter holes and cut. MAKE SURE THE ELECTRICAL WHIP COMING OUT OF THE WALL IS 1 BELOW THE CABINET. If not, lower as needed. OR
4 Layout for the electrical outlet, ALLOW 1 ON EACH SIDE AND TOP AND BOTTOM and cut the cabinet, as needed. THE ELECTRICAL COVER PLATE MUST BE FLUSH TO THE WALL. Continue down the wall installing a W2430 and a W3015 over the refrigerator. Go back to the corner and locate the W3630, the next cabinet going toward the kitchen window. Move the ledger to the front wall. Mark hinge location and remove the LEFT door ONLY and place the cabinet on the ledger. CHECK SHELF SUPPORTS TO ENSURE CABINET IS RIGHT SIDE UP. Attach the face frame to the corner cabinet, check for plumb and level and then attach to wall. Repeat the process starting from the other inside corner installing a Wall Corner 2430 and a W-2430, working back toward the kitchen window and then down the interior kitchen wall with 2-W3030 s. The ledger can be moved to the INTERIOR kitchen wall. BASE CABINETS: The BASE cabinet installation will start with a Lazy Susan, in the corner where the water line to the outside hose bib, is located. Remove the LS door. A ledger for the counter top may be needed in the corner behind the LS. Attach 1 x 4 with 2 ½ drywall screws into the blocking flush with the level line. Draw a plumb line DOWN the wall from the W 1230 that frames the Right side of the stove opening. This line will establish the LEFT edge of the Lazy Susan. Move the Lazy Susan into position. Shim as needed to bring the cabinet UP to the level line established in previous steps. Check for level in all directions before attaching to the wall. Position the Base 24 up to the level line, leaving a 30-1/4 opening between the front face frames of the cabinets for the STOVE. Attach to wall. Move the B-24 cabinet in place between the LS and the SB. MAKE SURE THE SIDES OF THE B-24 ARE UN FINISHED. Shim cabinet UP to the level line and attach to the face frame of the LS and to the wall. NOTE: Once base cabinets are level front to back, there still may be a gap between the back of the cabinet and the wall. THIS IS BECAUSE THE WALLS ARE OUT OF PLUMB. Place shims between the back of the cabinet and the wall, drill pilot hole and attach to wall with Specialty Cabinet Screws. DRILL HOLE ON EITHER SIDE OF THE SHIMS, NOT THROUGH THE SHIMS.
5 SETTING THE SINK BASE CABINET: This will be one of the more challenging cabinets to install, because of the cutouts for plumbing and electrical. Hold the H/C water lines plumb and mark their centerline and the PVC drain centerline on the wall. Extend the lines up the wall, just above the LEVEL cabinet line. Measure out 1 on each side and from the top and bottom of the electrical box. Extend the side lines above the level cabinet line. Measure DOWN from the cabinet level line to the line 1 above the electrical box and write the # on wall. Measure DOWN to the line 1 mark below the electrical box and write the # on wall. Establish the EXACT location of the Sink Base cabinet. The objective is to have the center of the SB MATCH the centerline of the window. However, reality is that it may be off depending on several factors. With the SB positioned against the B- 24, transfer the marks from the wall to the top, rear edge of the cabinet with a framing/speed square. Move the cabinet to center of the room. Place cardboard on floor and lay the cabinet face down on cardboard. Extend the lines for the electrical box down the rear of the cabinet using the numbers from the wall. Connect the lines and draw the outline for the electrical cutout. Verify the numbers. Then drill a hole in the corners and cut the opening with a jig saw. NOTE: Remove drywall screws in the sides and rear of the SB BEFORE install. They will interfere with the C-top install. Establish the distance from the wall to the centerline of the H/C water pipe and PVC drain line. Transfer the numbers to the floor of the SB cabinet. REMEMBER to subtract the thickness of the rear wall of the cabinet. Drill water lines holes with a 1 paddle bit and the drain pipe with a 3 hole saw. Hold the cabinet up above the pipes and feed the water lines through the holes and set the cabinet over the drain line on the floor. Check fit, adjust as needed and attach to wall.. A Blind Base Corner 45/48 cabinet will go next to the SB-36, and into the corner opposite the LS. This cabinet will be pulled off the interior wall to allow the adjoining cabinet, on the interior wall, to open. Install cover/filler to the open side of the BBC.
6 The B-36 that attaches to the BBC 45/48 will have a wide stile on the edge next to the BBC and the opposite side will UN-FINISHED. Locate and cut the heat duct by marking lines on the floor for the edge(s) of the duct. Position the B-36 and transfer the marks to the toe kick. Cut the toe kick out with a jig saw 3-1/2 up from the bottom of the cabinet. Level, shim and attach as before. Replace all the kitchen cabinet doors and adjust for proper gaps, as needed. Trim shims next to the walls as well as the floor. TOE KICK INSTALLATION: AFTER the flooring is installed, trim material will be installed to finish the toe kick area of the cabinets. Cut to length and install with sub-floor adhesive and 2 nails to secure while glue sets. NOTE: A cutout will be needed for a heat duct under the cabinet. Mark and cut the toe kick with a jig saw to match cutout in cabinet. BATHROOM VANITY: A 36 vanity will be installed in the Bathroom located tight to the Utility closet wall. Check wall for cabinet blocking. If there, proceed. IF NOT, locate studs to attach Vanity. VERIFY THE HEIGHT OF THE VANITY If 31- ½, establish a level line at that height above the floor. If NOT, use the height of the cabinet. Measure DOWN from the level to locate the centerline of the PVC drain line. Follow the same steps to locate the centerline of the H/C water lines. Transfer marks to rear of Vanity. Extend marks down the back of the Vanity and drill holes as needed. NOTE: Watch out for plumbing vent pipe, IN WALL, where PVC drain comes out of wall. Set Vanity in to place, shim to level and attach to wall. COUNTERTOP AND BACKSPLASH INSTALLATION: A pre-fabricated Laminate counter top and backsplash will be installed in the Kitchen and Bath. Drill holes in the triangles in the front corners of the Base Cabinets. SHORT drywall screws will be placed through these holes to secure the counter top.
7 AFTER removal of assembly screws, Cut the front and rear frame of the SB to prepare for the Counter-top install. The Kitchen sink wall and interior wall tops may be in 2 pieces and assembled on site. After assembly, place Sub Floor Adhesive along the rear, top of the cabinets, along the walls. Then slide the Top into its final position. 2 drywall screws will installed UP through the holes in the triangles and into the build up in the Top. The small top will be installed on the B-24 to the left of the stove with Sub Floor Adhesive along the rear wall and/or screws UP through the triangle in the front corners. Back splash will be cut to length, except for the B-24 piece, and installed with Sub Floor Adhesive. WHEN CUTTING THE BACKSAPLASH, CUT FROM THE UNFINISHED END ONLY. The B-24 backsplash may not need cutting. Mark and cut the Bath backsplash as above and glue in place. Short pieces of wood will be cut to hold the Backsplash in position until the glue sets. These will go between the top of the backsplash and the bottom of the upper cabinets. Cut them a little short and use shims for tight fit. TT 2/24/2015
HOW TO INSTALL A BEAUTIFUL NEW KITCHEN
HOW TO INSTALL A BEAUTIFUL NEW KITCHEN Easy to follow step-by-step kitchen cabinet installation TOOL AND MATERIAL LIST Hammer Pry bar Screwdriver Phillips Flathead Level Tape measure Pencil Straight edge
More informationKITCHENS. Tip PAGE 1 FITTING YOUR KITCHEN GUIDE. How to mark out a kitchen. Tools required for installing a kitchen STEP ONE STEP TWO STEP THREE
FITTING YOUR KITCHEN GUIDE How to mark out a kitchen PAGE 1 Before starting on the installation, measure 870mm from the lowest point of the floor and mark a datum line around the room to indicate where
More informationDIY CABINET REFACING INSTALLATION GUIDE
DIY CABINET REFACING INSTALLATION GUIDE CABINET REFACING INSTALLATION Are you ready to reface your outdated cabinets? This guide will show you how to install your new Facelifters Cabinet Refacing Products
More informationCabinetry Installation
Cabinetry Installation INTALLATION EQUIPMENT #8 x 2 1 2 screws #8 x 2 1 2 washer head screws Variable speed drill, electric or cordless Extension cord Countersink drill bit Drill bits, 3/16 and 1/4 Assorted
More informationDIRECTIONS FOR ASSEMBLING BASE & WALL CABINETS
DIRECTIONS FOR ASSEMBLING BASE & WALL CABINETS TheRTAStore.com STEP 1: CLEAR A WORK SPACE Place your RTA cabinet panels on a smooth, scratch resistant surface in a large, open area. (Some people like to
More informationComposite Stone Veneer
Composite Stone Veneer Installation Guide Ver 1 Jun 2015 www.compstone.com Composite Stone Veneer Installation Guide Contents Introduction & Overview 3 Required Tools 4 Optional Tools 4 Attachment Guidelines:
More informationWe urge you to read and follow the attached installation instructions. Failure to do so may void the warranty of this garden window unit.
Important Information for New Construction Installations Attention Installer! We urge you to read and follow the attached installation instructions. Failure to do so may void the warranty of this garden
More informationIrvinton Village Apartments 2901 Fulton Houston, Texas 77009 Houston Housing Authority J. Allen Management Managing Agent
Irvinton Village Apartments 2901 Fulton Houston, Texas 77009 Houston Housing Authority J. Allen Management Managing Agent Scope for Irvinton Village Unit #512 Overall Scope: Demolition, Renovation, and
More informationKITCHEN INSTALLATION GUIDE
KITCHEN INSTALLATION GUIDE The step-by-step guide to installing your new kitchen right The materials and tools you ll need This brochure is your guide to preparing and installing your new kitchen. Inside
More informationUB1 AIR CONDITIONING UNIT INSTALLATION INSTRUCTIONS
UB1 AIR CONDITIONING UNIT INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS: Carefully read these instructions before installing your new air-conditioner. AUSTRALIAN AUTOMOTIVE AIR AL00500054E 1 Table
More informationHow to Build a Poker Table
How to Build a Poker Table www.pokertablematerials.com 10-Person Poker Table- 96 x 48 These are step by step instructions for building a poker table. The table will measure 48" x 96" and have a 4" wide
More informationHow to Install GoBoard:
How to Install GoBoard: A Step-by-Step Guide Durable, Ultra-Lightweight, Waterproof Tile Backer Board Introducing GoBoard Every tiling project requires a durable, waterproof surface under the tile, called
More informationINSTALL INSTRUCTIONS KK-C-HVAC-1 HVAC UNIT 2003-2014 CHEVROLET/GMC VANS FOR
INSTALL INSTRUCTIONS KK-C-HVAC-1 HVAC UNIT 2003-2014 CHEVROLET/GMC VANS FOR (For NEW 2007 ALL WHITE KWIK-KITS ONLY) Warning do not attempt to install A/C units unless you are experienced with servicing
More informationKitchen Cabinets. Installing
Installing Kitchen Cabinets Careful planning and knowing exactly where the framing is help factory-made cabinets go in quickly and easily for a custom look with no nasty surprises BY KEVIN LUDDY THE STARTING
More informationINSTALLATION INSTRUCTIONS
door frames Engineered product systems INSTALLATION INSTRUCTIONS door frames MINIMALIST DOOR FRAME Fry Reglet Flush Door frames are designed for use with 3 5/8 studs with ½ drywall both sides (4 5/8 throat
More informationWren Kitchens Installation Tips... 3. Carefully check your kitchen delivery... 4. Measuring out and marking up... 5. Fitting the base cabinets...
tra 1 Index Wren Kitchens Installation Tips... 3 Carefully check your kitchen delivery... 4 Measuring out and marking up... 5 Fitting the base cabinets... 6 Fitting the corner cabinets... 7 The 972mm or
More informationDE Frame with C Series Sidelight
TOOLS REQUIRED Tape measure 6' magnetic level 3' magnetic level Screw gun with clutch adjusted #2 phillips tip #3 phillips tip Screwdriver (used to adjust frame on will using oval slots) Pry Bar Powder
More informationInstallation Guide. Bath and Wall Surrounds SERIES 7104 1021861-2-B
Installation Guide and Wall Surrounds SERIES 7104 1021861-2-B Thank You For Choosing Sterling We appreciate your commitment to Sterling value. Please take a few minutes to review this manual before you
More informationNew Home Walk-Through Package
New Home Walk-Through Package Carrying out a Successful Walk-through Before Closing John MacDonald Architect inc. The Courtyard @ Bonnie Stuart, 141 Whitney Place Suite 101, Kitchener, ON. N2G 2X8 New
More informationWe urge you to read and follow the attached installation instructions. Failure to do so may void the warranty of this garden window unit.
Important Information for New Construction Installations Attention Installer! We urge you to read and follow the attached installation instructions. Failure to do so may void the warranty of this garden
More informationCedar Cottage Doghouse Plans
Overlapping cedar shingles add an element of charm to this medium size doghouse. The walls, floor, and trim are constructed of solid cedar, making it naturally weather resistant and provides excellent
More informationWHI 90-Minute Rated Veneered Door Frame Installation Instructions
No. 940-03-10 INSTALLATION INSTRUCTIONS 90 MINUTE RATED VENEERED DOOR FRAME DOOR REQUIREMENTS: Consult the door manufacturer to make sure that the doors are qualified for the hardware to be installed,
More informationRouter Table Plans. www.bobsplans.com
www.bobsplans.com Router Table Plans Increase the capabilities of your router with this weekend project. Features a sliding fence with EZ-Mount clamps. These clamps are simple to make and grip tightly
More informationTexas Deparmtment of Housing and Community Affairs Community Development Block Grant (CDBG)
Texas Deparmtment of Housing and Community Affairs Community Development Block Grant (CDBG) Subrecipient Name: Homeowner Name: Home Address: Homeowner Signature: Building Contractor Name and Address: Work
More informationIMPORTANT INSTALLATION GUIDE VALENCIA SQUARE CORNER SHOWER READ ALL INSTRUCTIONS CAREFULLY BEFORE STARTING THE INSTALLATION
INSTALLATION GUIDE VALENCIA SQUARE CORNER SHOWER SEALANT REQUIRED TO COMPLETE THIS INSTALLATION: (Not supplied) Sika Sikasil NG (Arctic White) To seal the WHITE shower door and returns to the shower tray.
More informationGuidelines for Earthquake Bracing of Residential Water Heaters
Guidelines for Earthquake Bracing of Residential Water Heaters Department of General Services Division of the State Architect 1102 Q Street, Suite 5100 Sacramento, CA 95814 Phone: (916) 324-7099 Fax: (916)
More informationInstalling Window and Door Mouldings
Installing Window and Door Mouldings About Window and Door Mouldings The trim around windows and doors greatly influences the look and style of your interior. They also bridge the gaps and cover spaces
More informationYour Basement Remodeling Specialist LLC
Your Basement Remodeling Specialist LLC Contents Introduction 3 Remodel Details 4 Basement Bid Scope 5 Financial Arrangements 6 Homeowners Shopping Guide 7 The following is provided with your actual quote:
More informationGate Leg Drop Leaf Table Plans
Preparing the table top blanks: Cut and glue enough 3/4 stock to make three panels 40 long by 24 wide (they will be cut to final size at a later time). While the glue dries we will work on the legs. Preparing
More informationCooktop Low-Profile Ventilation Hoods
INSTALLATION GUIDE Cooktop Low-Profile Ventilation Hoods Contents Wolf Cooktop Low-Profile Ventilation Hoods........ 3 Cooktop Low-Profile Hood Specifications.......... 4 Cooktop Low-Profile Hood Installation............
More informationREDI-EXIT COMMERCIAL FIRE DOOR AND EXTERIOR DOOR KITS INSTALLATION GUIDELINES
REDI-EXIT COMMERCIAL FIRE DOOR AND EXTERIOR DOOR KITS INSTALLATION GUIDELINES Tools Required Tape Measure Hammer Slotted Screw Driver #2 & #3 Philips Screw Driver 3-4 Foot Level 12 Pry Bar Cold Chisel
More informationBeautiful kitchens and bathrooms to meet your budget! KITCHEN REMODELING BATHROOM REMODELING COUNTERTOPS AND MORE!
Beautiful kitchens and bathrooms to meet your budget! KITCHEN REMODELING BATHROOM REMODELING COUNTERTOPS AND MORE! QUALITY CABINETRY CUSTOM DESIGN PROFESSIONAL INSTALLATION SINCE 1989 WOW! DON T YOU DESERVE
More informationSAMPLE INSTRUCTIONS. Best Barns USA Assembly Book. the Denver. 12'x 12' or 12'x16' Revised November 29, 2010
Best Barns USA Assembly Book Revised November 29, 2010 SAMPLE INSTRUCTIONS the Denver 12'x 12' or 12'x16' Manufactured by Reynolds Building Systems, Inc. 205 Arlington Drive Greenville, PA 16125 724-646-3775
More informationwww.cornholesupplies.com
www.cornholesupplies.com How To Build Regulation Cornhole Boards Home of the Original Cornhole Bags and Boards Supply List: 1-4' X 8' Piece of Plywood (pre sanded) 4-2" X 4" X 8' Studs (2 by 4s make sure
More informationThis handout is a guide only and does not contain all of the requirements of the Minnesota State Building Code or city ordinances.
Basement Finishing Guide Community Development Department Building Inspections Division 5200 85 th Avenue North / Brooklyn Park, MN 55443 Phone: (763) 488-6379 / Fax: (763) 493-8171 6/15 www.brooklynpark.org
More informationChapter 3 Installing Over-the-Post Railing on an L-Shaped Stair
49 Chapter 3 Installing Over-the-Post Railing on an L-Shaped Stair In this chapter: The Over-the-Post Balustrade System Determining the Rail Centerline Using Rail Bolts Making a Pitch Block Laying Out
More informationBest Barns USA Assembly Book
Best Barns USA Assembly Book Revised November 27, 2013 the Easton - R 12'x 20' Manufactured by Reynolds Building Systems, Inc. 205 Arlington Drive Greenville, PA 16125 724-646-3775 This manual is copyrighted.
More informationSUMMARY OF WORK FOR GENERAL CONTRACTOR
SUMMARY OF WORK FOR GENERAL CONTRACTOR 1. General scope of work A. The work at 163 Seabrook consists of: 1. Finish the kitchen and 1 st floor hallway area 2. Finish 1 st floor bathroom and laundry area
More informationThe JIG is UP Or A couple hours up front pays in the long run.
Ed Simon Page 1 of 5 The JIG is UP Or A couple hours up front pays in the long run. A large part of the fun of beekeeping is the construction and assembly of the equipment. Since it is a hobby, I decided
More informationGuidelines for Earthquake Bracing Residential Water Heaters
Guidelines for Earthquake Bracing Residential Water Heaters Department of General Services Division of the State Architect In accordance with the Health and Safety Code Section 19215, the Division of the
More informationBrick Veneer Construction
Brick Veneer Construction Check list of suggested tools & support items Claw hammer Tape measure 3/4" [19 or 20] Wood chisel Wood or plastic shims Pry bar Utility knife Caulking and caulking gun Power
More informationTotal Quantity: IMPORTANT: Plans are to be used with 3 x6 Plexiglass (SKU #298-017).
# Materials: Quantity Each: 4x4x8 3 2x4x8 2 2x8x8 1 4x8x3/4 plywood 1 3 x6 corkboard (can be 18 of the 1 x1 pieces) 1 3 x6 plexiglass 1 8 door casing 3 Primer 1 qt. Total Quantity: TIPS FOR SUCCESSFUL
More informationMarch 14, 2007. Installation of Bay, Bow and Garden Windows
March 14, 2007 Re: Installation of Bay, Bow and Garden Windows Attached are the Atrium Companies, Inc recommendation for the installation of bay, bow and garden windows. These instructions were developed
More informationSliding Barn Door Hardware Installation Instructions BALDUR and ODEN
Sliding Barn Door Hardware Installation Instructions BALDUR and ODEN Installation Instructions Structural Information For standard systems and most custom single door opening systems. General Overview
More informationBasement Window Installation Guide Hopper and Sliding
Basement Window Installation Guide Hopper and Sliding americancraftsmanwindows.com Project Requirements: Installation must comply with all applicable building codes. Existing window frame, wall and weatherresistant
More informationSelf-Home Inspection Checklist
To be used as a first home visit for note taking. Visit www.homeinspectiondirect.com for more tips and information about buying a home and hiring a home inspector. This form in no way replaces a professional
More informationAssembly GUIDE. display wine cellar kits. Required. Suggested. Questions? 888.373.6057. or visit wineracksamerica.com
Page 1 Middle Ladder End Ladder Display Tray Screwless Connector Package Contents * All models follow the same assembly procedure varying only in the number of middle ladders your rack will require. Depending
More informationCongratulations on your new IKEA Kitchen, and on the money you saved!
Congratulations on your new IKEA Kitchen, and on the money you saved! INSTALLATION GUIDE FOR YOUR AKURUM KITCHEN Seven steps to a brand new kitchen It s time to discover another major advantage of investing
More informationBUILT-IN DISHWASHER INSTALLATION INSTRUCTIONS
BUILT-IN DISHWASHER INSTALLATION INSTRUCTIONS PLEASE READ COMPLETE INSTRUCTIONS BEFORE YOU BEGIN LEAVE INSTALLATION INSTRUCTIONS AND USER'S GUIDE WITH OWNER ALL ELECTRIC WIRING AND PLUMBING MUST BE DONE
More informationGENERAL WIRING RULES FOR HOUSES
GENERAL WIRING RULES FOR HOUSES 1. Romex has to be installed in drilled holes in joists or studs even above suspended ceilings - No stapling to bottom edges of joists or studs. You may staple wire to flat
More informationQWALL 4 ACRYLIC SHOWER WALL INSTALLATION INSTRUCTIONS
QWALL 4 ACRYLIC SHOWER WALL INSTALLATION INSTRUCTIONS IMPORTANT DreamLine TM reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical
More informationBuilding Condition Assessment Report
Building Condition Assessment Report Asset C3c - Oak Terrace Cottage 121 Address Riverview Lands, 2601 Lougheed Highway, Coquitlam, BC. V5C 4J2 Construction Year Size (Gross Floor Area) 1920. 2,553 Sq.Ft.
More informationWOODLAND HOMES BUILDING PROCESS A STEP BY STEP CONSTRUCTION GUIDE TO YOUR NEW HOME
WOODLAND HOMES BUILDING PROCESS A STEP BY STEP CONSTRUCTION GUIDE TO YOUR NEW HOME 1 THE BUILDING PROCESS The focus of Woodland Homes building department is Quality, Service and Predictability. Through
More informationClad Direct Glaze Window Installation Instructions
Clad Direct Glaze Window Installation Instructions Sill flashing and sealing: 2. An overview of the proper flashing sequence is shown in figure 1. Please read entire installation instructions carefully
More informationSUPER SHED. Indoor shelter for your outdoor tools.
SUPER SHED Indoor shelter for your outdoor tools. Not everyone needs a garden shed. But, if you've no more space on your garage wall for that new leaf rake, if you can't find your potting trowel because
More informationInstallation Manual. Toilet Partitions, Dressing Compartments & Shower Stalls
Installation Manual Toilet Partitions, Dressing Compartments & Shower Stalls Metpar Corp 95 State Street, Westbury, New York, USA, 11590 Tel: 516-333-2600 Fax: 516-333-2618 Internet: http://www.metpar.com
More informationGarage Workbench Plans
www.bobsplans.com Garage Workbench Plans Every home woodworker knows the importance of making efficient use of the available space in his or her shop. This workbench is designed to provide the maximum
More informationSliding Door Hardware Installation Instructions
Sliding Door Hardware Installation Instructions Installation Instructions Structural Information For standard systems and most custom single door opening systems. General Overview ff All Krown Lab sliding
More informationInstallation Instructions
Installation Instructions 1. Position the unit onto bridging packers. These keep the unit away from any water sitting inside the frame. 2. Centralise the unit within the frame and pack the edges with appropriate
More informationEucaboard / Eucaplac/ Eucatile paneling is intended for dry interior use only and requires care in handling.
i This instruction sheet describes the proper methods for installing Eucatex decorative wall paneling. Eucaboard / Eucaplac/ Eucatile paneling is intended for dry interior use only and requires care in
More informationHow To Install Your Frameless Shower Enclosure
How To Install Your Frameless Shower Enclosure a) Installing Single Frameless Door Side Mounted Wall Hinges b) Installing Frameless Door with In-Line Panel c) Installing Frameless Door Between In-Line
More informationBlack Wolf POCKET BILLIARD TABLE INSTALLATION MANUAL. SERVICE DEPARTMENT P.O. BOX 68 BRISTOL, WI 53104
Black Wolf TM POCKET BILLIARD TABLE INSTALLATION MANUAL www.brunswickbilliards.com SERVICE DEPARTMENT P.O. BOX 68 BRISTOL, WI 53104 51-905710-000 SEPTEMBER 2010 NOTE: Please use the instructions in this
More informationWindow Installation Instructions
Caution The correct installation methods of windows in full frame or insert applications is critical towards achieving the tested performance of the window and longterm enjoyment and energy savings for
More informationSchedule of Maintenance Fees
Schedule of Maintenance Fees Effective July 1, 2015 It is the policy of the Housing Authority of Murray not to charge for NORMAL wear and tear. However, the Housing Authority reserves the right in every
More information604 Water Closets and Toilet Compartments
604 Water Closets and Toilet Compartments 604.1 General. Accessible water closets and toilet compartments shall comply with Section 604. 604.2 Location. The water closet shall be positioned with a wall
More informationCOMPLIMENTARY WOODWORKING PLAN
COMPLIMENTARY WOODWORKING PLAN Adirondack Chair This downloadable plan is copyrighted. Please do not share or redistribute this plan in any way. It has been created for Wilton Tools, a division of WMH
More informationBUILT-IN MICROWAVE OVEN INSTALLATION INSTRUCTIONS
UILT-IN MIROWVE OVEN INSTLLTION INSTRUTIONS 24" (61.0 cm), 27" (68.6 cm), 30" (76.2 cm) This product is suitable for use above electric or gas built-in ovens, and below non-vented electric or gas cooktops.
More informationIMPROVEMENT COST ESTIMATE powered by HomeFixers
IMPROVEMENT COST ESTIMATE powered by HomeFixers 123 Main St, Anytown, USA 12345 2000 SF $ 45,041.06 100.0% $22.52 per sq. ft. Stage 1: Pre-Construction $ 1,461.00 3.2% 1 House Secured $ 106.00 0.2% Lockbox
More informationBase Cabinet with Self-storing Folding Doors and Floor
Usable Kitchens When designing a kitchen for use by persons with mobility impairments, especially those who use wheelchairs, careful layout of the kitchen is crucial to maintaining accessibility. People
More informationINSTALLATION OF A BAY WINDOW
INSTALLATION OF A BAY WINDOW Installation of a Bay Window These instructions relate to the replacement of an existing bay window or replacement of a straight window with a new bay window, in an opening
More informationThese instructions will show you how to install an internal door into a non-loadbearing partition wall. The instructions are split into three parts.
No 8 in the series of 'How to' brochures produced by PlaceMakers, New Zealand How to Frame and Hang a Door These instructions will show you how to install an internal door into a non-loadbearing partition
More informationTOLL FREE: (866) 591-7792. E-Mail: techmail@vigoindustries.com. www.vigoindustries.com VANITY SPECIFICATIONS. VANITY COMPONENTS Model VG09042K1
VANITY SPECIFICATIONS VANITY COMPONENTS Model VG09042K1 MODEL VG09042K1 FEATURES Freestanding cabinet Soft closing sliding cabinet drawer hardware White, single hole ceramic sink Cabinet ships assembled
More informationLadder Shelf Plans Final dimensions: 25 L x 21 W x 72 H
Ladder Shelf Plans Final dimensions: 25 L x 21 W x 72 H Copyright 2011. MLCS Woodworking. Page 1 Router bits and supplies needed: 3/8 Rabbeting bit (#10691) 1 Bottom Cleaning bit (#7941) Top and Bottom
More informationINSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS
BATH SINKS INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Caution: All installation types need to allow room for faucet installation. Ensure adequate clearance behind the basin for your faucet and
More information11339 Georgia Ave Wheaton, MD 20902 phone: fax: 240.483.4975
11339 Georgia Ave Wheaton, MD 20902 phone: fax: 240.483.4975 Thank you for choosing Counter Culture to template, fabricate and install your new countertops. We will do our best to delight you with our
More informationPremier & Deluxe 3-Season Room Sliding Glass Door
DTSSGD-11 Premier & Deluxe 3-Season Room Sliding Glass Door Installation Instructions Screen Door Seal Left Side Track Top Track Assembly Right Side Track Right Side Trim Sliding Glass Door Sliding Screen
More informationCORNER FRIDGE REFRIGERATION UNIT INSTALLATION AND OPERATION INSTRUCTIONS
CORNER FRIDGE REFRIGERATION UNIT INSTALLATION AND OPERATION INSTRUCTIONS D E F Y I N G C O N V E N T I O N Congratulations on your new Corner Fridge Your new corner fridge may have different functions
More informationGreat Beginnings. Merillat Essentials
Great Beginnings. Merillat Essentials Sensibility+you. Where it all begins. The start of a meal. The core of the home. The center of life. The kitchen brings together all of the elements of life, and Merillat
More informationNew Employee / Applicant - Information Pack (Includes: Driver Back round Release Form, Skills & Tools Assessment
New Employee / Applicant - Information Pack (Includes: Driver Back round Release Form, Skills & Tools Assessment Included are the following: Personal information form Driver Back round Check Authorization
More informationSash Replacement Guide
for Andersen 200/400 Series Awning Windows Read all instructions carefully before attempting this procedure. If you have any questions about your ability to complete this procedure, call Andersen at 1-888-888-7020
More informationCeiling Mounted Folding Attic Ladders Installation Instructions
Ceiling Mounted Folding Attic Ladders Installation Instructions WARNING Before you start installing your new Louisville Ceiling Mounted Folding Attic Ladder, you must read and understand the following:
More informationDo it yourself guide to installing your kitchen
Do it yourself guide to installing your kitchen Design and Quality IKEA of Sweden In most kitchens, it s easiest to install the wall cabinets first. This way there won t be any base cabinets to work around
More informationHolz Choices & Specifications
March 21, 2011 0. SALES AND DESIGN 1. UTILITIES AND PERMITS Holz Choices & Specifications 2. EXCAVATION AND LOT PREPARATION Job Beginning date of Monday May 2 nd, 2011 ALTERNATE: Garage walls as drawn
More informationAbove-Counter Bathroom Sink
P72060 P72061 P72064 P72065 P72066 P72067 1 of 5 THANK YOU FOR CHOOSING KALLISTA We appreciate your commitment to KALLISTA quality products. Please take a moment to review this manual before you install
More informationCOST OF WORK FORM. Abbreviations: ea = each, LF = linear feet, SF = square feet, HSF = square feet of living area (including garage conversion space)
COST OF WORK FORM All costs shown are estimates using base grade materials, taxes, and labor. For houses where a higher quality is indicated, the costs should be increased for work requiring upgraded materials.
More informationInspection Item COMMENTS
APPENDIX 9 AFFORDABLE HOUSING PROGRAM INSPECTION CHECKLIST Participating Jurisdiction: Homeowner Name: Assisted Property Address: Date of Physical Inspection of Property: Total Square Footage of Property:
More informationStanley Neighborhood Series
Stanley Neighborhood Series On the Outside - Appealing Exteriors Maintenance Free Double 5 Siding Per Design 25Year Shingles New and Appealing Exterior Elevations Portico, Porches and Covered Entry Per
More informationSun Windows General Information Sun New Construction Window Installation Instructions
Sun Windows General Information Section 1 G F H H H A. Apply Weather Resistive Barrier B. Apply Sill Flashing Tape C. Place Waterproof Sill Shims D. Caulk Back of Nail Fin Sides & Top, Set Window, Fasten
More informationYou can do it all yourself. But you don t have to.
You can do it all yourself. But you don t have to. IKEA Professional Kitchen Services. We ll take it from here. A high standard of accuracy has been sought in the preparation of this brochure. We apologize
More informationHfHMD uses LP SmartSide siding and trim.
HfHMD uses LP SmartSide siding and trim. These products are: More durable than cement fiber board. Much more volunteer-friendly to install. When installed correctly, have a 5/50- year pro-rated warranty.
More informationBorges Construction Company A limited liability Corporation Page1 of 1
Page1 of 1 The following is a quote to remodel the master bathroom at your home: Materials Labor Demolition 1 Dumpster $ 225.00 $ - 2 Remove existing carpet $ - $ 50.00 3 Remove existing tile $ - $ 80.00
More informationInsulView Window Installation Instructions
InsulView Window Installation Instructions 1. The entire building is normally sheeted with the 2" 2 ½ OR 3 wall panel and the windows installed at a later time. A window retrofit of an existing building
More informationINSTALLATION INSTRUCTIONS for Bifold Doors (JII103)
Thank you for selecting JELD-WEN products. Attached are JELD-WEN s recommended installation instructions for premium composite, hollow and solid core molded Bifold Doors. Bifolds are designed for fast
More informationKitchen & Bath Measurements Guide
Kitchen & Bath Measurements Guide High End design without High End pricing Kitchen & Bath Measurement Guide ABOUT US Interstock Premium Cabinetry (IPC) is a manufacturer and importer of kitchen cabinets
More informationREAD THE INSTRUCTIONS SEVERAL TIMES BEFORE STARTING ASSEMBLY
1954-87 CHEV BED INSTRUCTIONS (Revised Nov 2002) Thank you and congratulations on your purchase of the finest Street Rod Pickup Bed on the market today. The following instructions should help you assemble
More informationInspection Report of 1895 Jamesport Circle PSL, Fl 33953 Prepared for Yen Ho
Inspection Report of 1895 Jamesport Circle PSL, Fl 33953 Prepared for Yen Ho The State of Florida requires the builder to build in compliance with the Florida Building Code. Florida State Statutes 455
More informationPDmB, Inc. Definitions
Page 1 of 11 Definitions S Satisfactory Meets industry standards for proper material and installation NP Not Present Condition or item was not present at time of inspection NI Not Inspected Condition or
More informationFTC 2015-2016 DIY Mountain Build Guide
FTC 2015-2016 DIY Mountain Build Guide Assembly Instructions Check out the DIY2015-2016 Prints and BoM for individual part details. Release 1.0 9/10/15 Page 1 This guide and Bill of Materials are for constructing
More informationHow you select and where to install me! Kitchen BE CAREFUL OF FOLLOWING PARAMETERS : A- Plumbing space needed (specifically the height).
Environment, recycling, selective collect Today, to convert a house to recycling, a house should have necessary methods and tools. Richelieu, always ahead of practical solutions, offers management and
More informationTHINGS YOU SHOULD KNOW
INSTALLATION INSTRUCTIONS Value Sized Roll The quickest, easiest, cleanest way to install tile. No Mortar, No Mixing, No Mess Complete Your Project in a Day No Waiting Between Setting and Grouting THINGS
More information