Drum set : Assembly Instructions

Transcription

1 Front Right side View of completed model Back Left side A drum set is a collection of various types of drums, cymbals and other percussion instruments that are lined up in a formation that makes them easily played by one person. The number and type of instruments included can be arranged according to the performer's preference or characteristics of the music. The performer usually plays seated on a stool. The idea for the drum set is said to have originated in military bands, when a cymbal was placed on top of the bass drum to make it easier for the performer holding it. This was followed by the idea to use a pedal to play the bass drum with the foot, and the invention of the hi-hat, two cymbals on top of each other that are clashed together. These adaptations have resulted in the drum set up and beat style we know today. Parts sheet (Pattern) : Twenty-two A4 sheets (No.1~No.22) No. of Parts : 384 Assembly Instructions : Ten A4 sheets (No.1~No.10) *Build the model by carefully reading the Assembly Instructions, in the parts sheet page order. *Assembly will be easier if you write the part's number on the back of each part. Handy Hint Trace along the folds with a ruler and a used pen (no ink) to get a sharper, easier fold. Assembly Instructions Tools and materials Assembly tip Caution Mountain fold (dotted line) Make a mountain fold. Valley fold (dashed and dotted line) Make a valley fold. Scissors line (solid line) Cut along the line. Cut In line (orange solid line) Cut a slot. Cut out (orange shaded) Cut out the area marked. The glue spot(colored dot) shows where to apply the glue. Glue spot (Red dot) Glue parts with the same number together. Glue spot (Green dot) Glue within the same part. Glue spot (Blue dot) Glue to the rear of the other part. Glue spot (Yellow dot) Apply glue to the back, and attach to the back of the other parts. Scissors, set square, glue (We recommend stick glue),pencil, used ballpoint pen, toothpicks, tweezers, (useful for handling small parts) Before gluing, crease the paper along mountain fold and valley fold lines and make sure rounded sections are nice and stiff. Glue, scissors and other tools may be dangerous to young children so be sure to keep them out of the reach of young children. PAGE01

2 Before starting. Drum set : Assembly Instructions Each page of the "Parts sheet" has a sheet number in the top left-hand corner (Sheet No.1~No.22). Work in order of these sheet numbers. (The parts for assembly are on pages 2 ~ 22.) There are 384 parts in total, and each part is numbered according to its page. Also, the glue spots on each part are marked with the number of the part to attach to them. The numbers ~ in the Assembly Instructions indicate the order to attach parts. Follow this order when attaching. When one part has multiple spots to attach, or glue spots for attaching other pieces, colors ( ) and numbers are used to show the precise location and method for attaching. Check the diagrams in the "Assembly Instructions" carefully for each part as you work. PAGE03 Align the marker lines on 3A and 3B with the glue spots on 3C ~ 3H, PAGE02 Back side *Take note of where the thick marker line is. sides Front side Handy Hint: Wrapping the piece around a can or other cylindrical object will result in a neater finish. *NB: Begin from the opposite side to the seam. Back side *NB: Align the thick marker line with the upper part, and insert it through to the front side. Do not apply glue. Back side Front side Front side Diagonal line Seam *Attach to the display stand later. Back side Front side PAGE02

3 PAGE04 PAGE05 *Roll up Seam line Inside Align the seam lines and insert the pieces inside each other, and attach to the specified position. Face the seam line inwards and insert the piece to the position specified. Wrapping the piece around a thin cylindrical object will result in a neater finish. *Attach the back. PAGE06 Tom-tom 13" x 10" *Be sure to align the thick black marker lines on the top and bottom (circled here in blue) when attaching. Align the marker lines on 6A and 6B with the glue spots on 6C ~ 6H, *Roll up *Do not attach the area marked with the diagonal lines. Assemble both the left and right parts so that their seams face outwards. *After attaching, swivel the pieces around as shown, so that the seams face inwards. sides *Attach the parts circled in blue around the tom holder pipes so that the pipes are held up vertically. Tom holder pipe *Take note of where the thick marker line is. PAGE03

4 PAGE06 Tom-tom 13" x 10" PAGE07 Tom-tom 12" x 9" *Be sure to align the thick black marker lines on the top and bottom (circled here in blue) when attaching. Align the marker lines on 7A and 7B with the glue spots on 7C ~ 7H, sides *Take note of where the thick marker line is. *Before attaching parts 6O and 6P, bend them into shape as shown in the diagram. *Begin from the opposite side to the seam. Specified position *Begin from the opposite side to the seam. Seam Take note of the markings *NB: Align the thick marker line with the specified position on the upper part, and insert it through. Do not apply glue. Seam *Before attaching parts 7P and 7Q, bend them into shape as shown in the diagram. *NB: There are 12 6Q parts altogether. One of them, marked 6Q-1, has a specific location for attaching. Specified position *NB: Align the thick marker line with the specified position on the upper part, and insert it through. Do not apply glue. *Do not apply glue to. *Do not apply glue to. Take note of the markings *NB: There are 12 7R parts altogether. One of them, marked 7R-1, has a specific location for attaching. PAGE04

5 PAGE / Tom-tom 13" x 10" / Tom-tom 12" x 9" PAGE08 Floor tom *Begin from the opposite side to the seam. Shell Lug Head Tom holder Seam Lug bar *Before attaching parts 8F and 8G, bend them into shape as shown in the diagram. *NB: There are 16 8H parts altogether. Tom-tom 13" x 10" front head Tom-tom 12" x 9" hook PAGE09 Floor tom Align the marker lines on 9A and 9B with the glue spots on 9C ~ 9H, *Be sure to align the thick black marker lines on the top and bottom (circled here in blue) when attaching. sides *Take note of where the thick marker line is. *Do not apply glue to. Specified position *NB: Align the thick marker line with the specified position on the upper part, and insert it through. Do not apply glue. *Take note of where the thick marker line is. PAGE05

6 PAGE09 Floor tom Align the marker lines on 10A and 10B with the glue spots on 10C ~ 10H, *Be sure to align the thick black marker lines on the top and bottom (circled here in blue) when attaching. *Take note of where the thick marker line is. sides Head Snare wire picture Lug *Align the snare wire position here. Shell Leg *Do not apply glue to. Align the snare wire position and fit the head on. Do not apply glue. Snare wire position *After completing the stand, place the snare drum on the arm. Do not apply glue. Shell Head Lug PAGE10 Snare drum *Begin from the opposite side to the seam. Rubber arm Stand PAGE11 Snare drum sides *Roll up Seam *Roll up *Before attaching parts 10R and 10S, bend them into shape as shown in the diagram. *NB: There are 8 10T parts altogether. PAGE06

7 PAGE12 Ride cymbal sides *Align the reverse sides PAGE13 Crash cymbal sides sides Cymbal stand nut Felt for clutch Cymbal sides Die-cast joint Angle adjustment tilter Cymbal Stand Die-cast joint Die-cast joint Stand Die-cast joint *Roll up *Roll up PAGE07

8 PAGE14 Hi-hat cymbal PAGE14 15 Hi-hat cymbal *Back side of 14C Extension rod Hi-hat clutch Hi-hat cymbal sides Curl. Die-cast joint Stand *Roll up *Roll up *Do not apply glue to. *Put the pieces back to back and attach together. Foot pedal Foot pedal *The hi-hat cymbal moves when you press the foot pedal. PAGE08

9 PAGE15 Drum pedal PAGE16 Drum stool sides *Back side of 16B sides *Roll up *Bend the pieces left and right to open a gap. Do not apply glue. Seat sides Leg Felt beater Frame Foot pedal *The felt beater moves when you press the foot pedal. PAGE09

10 PAGE Display stand PAGE21 22 Display stand PAGE20 21 Display stand Ride cymbal Crash cymbal Tom-tom 13" x 10" Tom-tom 12" x 9" Hi-hat cymbal *Fold inside Snare drum Floor tom Drum stool Drum pedal View of completed model *The completed photo is an image of a basic drum set. The parts can be arranged to your liking. PAGE10