CX-CT6C. 2.4GHz 6 Channel FHSS Technology Digital Proportional Radio System. Copyright 2011 KY MODEL Company Limited.

Transcription

1 CX-CT6C 2.4GHz 6 Channel FHSS Technology Digital Proportional Radio System INSTRUCTION MANUAL Copyright 211 KY MODEL Company Limited.

2 MENU Table of content Introduction Caution Transmitter Chart 2.4G Binding Heli. Connection Diagram (3 Servos CCPM) Airplane Connection Diagram V-Tail COnnection Diagram DELTA-MIX Connection Diagram CX-CT6C Basic Features LED Displaying Board Function Menu System Menu MODEL.SET PLANE TYPE Function Menu (Heli.) D/R SUB. TRIM TRAVEL CH.REV SWASH.MIX GYRO.SENS THRO.CURV MONITOR PIT.CURV THRO.HOLD Function Menu for Fixed Wing Plane Function Menu for V-Tail Function Menu for Delta Mix Technology Data

3 1. Introduction Thank you for purchasing the CopterX CX-CT6C digital proportional radio system. With advanced micro processor control, large LCD display, glitch free FHSS 2.4GHz system, multiple model memory, build-in program for helicopter, airplane, v-tail and delta wing. Make this one of the most advance radio system in the market. Please keep this manual for future reference. 2. Caution CX-CT6C Please read this manual carefully and keep it for reference in the future. Warning: 1. This product was designed only for radio controlled models; 2. The usage of this product should be approved by local relevant law or regulations; 3. We will not be responsible for the damages caused by unauthorized modification, adjustment or replacement of parts of this product; 4. The manual may be altered without prior notice. Please contact us if you have any corrections or clarifications that should be made in the manual. Please pay more attention to the parts in this manual, which are marked with Warning Before starting the transmitter, make sure the transmitter batteries are well loaded and with enough power. And please check and confirm that the servos are all well and properly connected. Please take off batteries from transmitter after flying and during the transportation. Please check and have a test on control surfaces to confirm the transmitter handling of each part prior to each takeoff. Keep the radio system away from moisture, high temperature and strong vibration. Do not clean the product with solvent. Do not fly your models near airfield, schools, hospitals, residences, power transmission network, communication facilities and other places that are forbidden for starting the transmitter. Please stop flying your models with the radio on rainy or windy days, or at night. Do not fly the models when you are tired, sick, intoxicated, or not in good spirit. The antenna does not touch anything else when power switch is turned on. Do not leave this product and its accessories within the reach of small children. Please use this product according to your local relevant law or regulation, we are not responsible for any incidents or damages. 2

4 3. Transmitter Chart Antenna Hover pitch Hover throttle IDLE switch TH. Hold (Heli.) CH 5 (Plane) (Heli.) A/E/R DR (Aile, Elev, Rudd) Digital trim Left stick Hook Digital trim Power switch LCD display UP DOWN EXIT GYRO.SENS (Heli.) CH 6 (Plane) Digital trim Right stick Digital trim INCREASE DECREASE Charging jack G Binding The binding process: turn on the transmitter, then connect the power of receiver keeping the receiver BIND button till the light turn on GREEN which means the binding is successful. After that, it is unnecessary to bind again. Caution: make sure the RX and TX is within one meter, and around 1 meters no similar device. If the light flashing, showing the binding failure, please do again as above indication. 3

5 5.1. Heli. Connection Diagram (3 Servos CCPM) Switch to HELIC position and enter Helicopter mode. (AILE.) (ELEV.) Front (PITCH) Gyro RUDD. Servo 4 Receiver Remote Gain Rudder ELEV. PITCH Servo 3 Power Electronic Speed Controller Motor AILE. Servo 1 Servo 2 4

6 5.2. Airplane Connection Diagram Switch to plane position and enter Airplane mode, not mix function, as for normal planes. Receiver channel distribution: CH1: Aileron CH2: Elevator CH3: Throttle CH4: Rudder CH5: Gear CH6: Flap AILE. AILE. RUDD. ELEV. Servo 5 Flap Servo 4 Receiver Gear RUDD. ELEV. Servo 3 Power Electronic Speed Controller Motor AILE. Servo 1 Servo 2 5

7 5.3. V-Tail Connection Diagram Switch to V-Tail position and enter V-Tail mode, elevator and Rudder is mixed, as for V-Tail planes. Receiver channel distribution: CH1: Aileron CH2: Ruddervator (Tail) CH3: Throttle CH4: Ruddervator 2 (Tail) CH5: Aileron DELTA-MIX Connection Diagram Switch to DELTA position and enter DELTA-MIX mode, aileron and elevator is mixed, as for triangle planes, tailless planes, discal planes. Receiver channel distribution: CH1: Eleron CH2: Eleron 2 CH3: Throttle CH4: Rudder 6

8 6. CX-CT6C Basic Features 1. Pitch neutral trim 2. Output standard 6 channel signal and support 2.4G sytem 3. Support 3D fly mode, normal fly, idle 1 fly and idle 2 fly (in the idle mode) 4. D/R for Aileron, elevator, rudder 5. Throttle hold function 6. Gyro sensitivity adjustment 7. Channel neutral position setting 8. Channel reverse and channel servo travel adjustment 9. Six models data memory 1. LED will blink with alarming when the voltage is low 7. LED Displaying Board Function POWER LED The light keeps on with blue color in normal power-on condition. When the voltage is below 4.V, the light blinks with alarming. Now please exit the operation and change new battery. NOTE: If THRO HOLD is shown on LCD when you turn on the power, please move TH. HOLD switch to the position, otherwise, you can not properly enter power on interface. 1.V CT6C TH. HOLD THRO HOLD FUN. MENU SYS. MENU NOTE: If IDLE ON is shown on LCD when you turn on the power, please move IDLE switch to the position N, otherwise, you can not properly enter power on interface. 1.V CT6C IDLE IDLE ON FUN. MENU SYS. MENU 7

9 8. Menu FUN. MENU D/R SUB.TRIM TRAVEL CH.REV SWASH.MIX GYRO.SENE THRO.CURV MONITOR PIT.CURV THRO.HOLD SYS. MENU HELIC PLANE V-TAI DELTA D/R SUB.TRIM TRAVEL CH.REV MONITOR D/R SUB.TRIM TRAVEL CH.REV MONITOR V-TAIL D/R SUB.TRIM TRAVEL CH.REV MONITOR DELTA-MIX HELIC PLANE V-TAI DELTA MODEL.SET PLANETYPE STICKMODE MODEL.SET PLANETYPE STICKMODE MODEL.SET PLANETYPE STICKMODE MODEL.SET PLANETYPE STICKMODE 1. MODEL.SET: Here you can set the parameter of the model, rename, save and format the corresponding model parameter, and come back to the factory setting. 2. PLANETYPE: Four types of plane are selectable. Helicopter, fixed wing(plane), V-Tail and Delta. 3. STICKMODE: Operating stick selection: Mode 1 (right throttle), Mode 2 (left throttle), Mode 3 and Mode : Neutral position setting of 4 proportional channels controlled by the operating stick. 5. : This menu can be used for simulator setting. 8

10 9.1. System Menu 1.V CT6C FUN. MENU SYS. MENU MODEL.SET MODEL MOD RENAME SAVE AS RECOVER PLANE TYPE MODEL.SET PLANE TYPE PLANE HELICTYPE PLANE STICK V-TAIMODE DELTA MODE 1 RU AI EL TH MODEL.SET PLANE TYPE RENAME MOD A BCDEFGHIJ KLMNOPQRST UVWXYZ MODE 2 RU AI TH EL MODEL MOD RENAME SAVE AS RECOVER MODE 3 AI RU EL TH MODEL MOD RENAME SAVE AS RECOVER MODE 4 AI RU TH EL STICK ADJ NORMAL STICK ADJ 9

11 9.2. MODEL.SET MODEL.SET PLANE TYPE MODEL MOD RENAME SAVE AS RECOVER Recall Model 1. Press up or down to select, and press to come to the interface. 2. Press to come to MODEL.SET interface, and now the shadow area is the item that can be set currently. 3. Press INC or DEC to select mode you expect. The default setting are Mod1, Mod2, Mod3, Mod4, Mod5, Mod6. 4. Press to confirm when a model number is selected, otherwise your selection is invalid. Remark: when your selection is successful, the model naming area in the main interface will show the corresponding change. Please note: All your settings have been saved in the current model number. MODEL MOD RENAME SAVE AS RECOVER RENAME UOD A BCDEFGHIJ KLMNOPQRST U VWXYZ Rename model 1. Press up or down to select, and press to come to the interface. 2. Press to come to MODEL.SET interface, and now the shadow area is the item that can be set currently. 3. Press up or down to select the setting function items, and press to come to RENAME 4. Move the stick in left stick four directions to select letters or digits to rename your item. Press to confirm when letters or digits are selected, otherwise your selection is invalid. Caution: When cannot select letters to the left need redone. Remark: when the cursor is at or, press to quickly change the single letter of the name. 1

12 MODEL MOD RENAME SAVE AS RECOVER MODEL MOD RENAME SAVE AS RECOVER Save as model number 1. Press down to select, and press to come to the interface. 2. Press to come to MODEL.SET interface, and now the shadow area is the item that can be set currently. 3. Press up or down to select the setting item, and press to come to SAVE AS 4. Press up or down to select your model number to be saved. Press to confirm when the number is selected. It can be saved again and again in different model number groups. Press EXIT to leave the setting. Remark: the data of the current model will copy to another memory slot, so please be careful. MODEL MOD RENAME SAVE AS RECOVER MODEL MOD RENAME SAVE AS RECOVER Recover the factory data 1. Press down to select, and press to come to the interface. 2. Press to come to MODEL.SET interface, and now the shadow area is the item that can be set currently. 3. Press up or down to select the setting item, and press to come to RECOVER 4. Press to recover the factory setting, and press EXIT to leave the menu. Remark: This recovery will clear the data of the current model, please be careful. 11

13 9.3. PLANE TYPE MODEL.SET PLANE TYPE MODEL.SET PLANE TYPE PLANE HELICTYPE PLANE STICK V-TAIMODE DELTA Plane type selection 1. Press down to select, and press to come to the interface. 2. Press up or down to select PLANE TYPE, and now the shadow area is the item that can be set currently. Press to go to the next step. 3. Now comes out a dialing box, press up or down to select HELIC, PLANE, V-TAIL or DELTA. And press to save the setting and leave the operation MODE 1 MODE 2 MODE 3 MODE 4 EL RU AI TH TH RU AI EL EL AI RU TH TH AI RU EL Stick mode selection 1. Press down to select, and press to come to the interface. 2. Press up or down to select, and now the shadow area is the item that can be set currently. Press to og to the next step. 3. Press up or down to select MODE 1 (right throttle), MODE 2 (left throttle), MODE 3, MODE 4. And press to save the selection and press EXIT to leave the operation. Remark: This operation changes the distribution of 4 proportional channels. Please note: AILE, ELEV, THRO and RUDD channels have been distributed now. When the stick model is changed, the menu order controlled by the stick AI and EL is also changed. Please pay attention to the difference. 12

14 9.5. Stick neutral position setting 1. Press to come to interface, and now the shadow area is the item that can be set currently. 2. Before your operation, please be sure that the 4 proportional channels of the sticks are in the neutral position and the 4 electronic trim buttons are also in the neutral position. 3. Press to enter, and now comes out a dialing box. Press up or down to select NO or YES, and press. When you hear one beep sound, the neutral setting is successful. 4. Press EXIT to save and leave the setting STICK ADJ NORMAL STICK ADJ Trainer mode selection 1. Press down to select, and press to come to the interface. 2. Press up or down to select NORMAL or. NORMAL: normal fly, : simulator software NOTE 1. This function is for simulator operation in the computer, optional simulator cable and software require. 2. Please do not connect Trainer interface at the back of the transmitter to any electric equipment or other radio transmitters, or else, we are not responsible for any damages. 3. This interface does not support training function, it is only for flying simulation software. Simulating JACK 13

15 1.1. Function Menu (Heli.) 1.V CT6C FUN. MENU SYS. MENU D/R SUB. TRIM TRAVEL THRO.CURV MONITOR PIT.CURV CH.REV SWASH.MIX GYRO.SENE THRO.HOLD D/R H I O L DR 1 1 SUB. TRIM CH.REV AILE SUB. TRIM AILE ELEV THRO TRAVEL TRAVEL AILE 1 1 ELEV 1 1 THRO 1 1 REV.SW CH REV NOR H I O L DR 1 1 ELEV SUB. TRIM RUDD GEAR PITH TRAVEL RUDD 1 1 GEAR PITH H I O L 14 DR 1 1 RUDD

16 SWASH.MIX SWASH.MIX AILE -5 PITH -5 ELEV -5 GYRO.SENE GYRO.SENS POS -1 POS1 1 THRO.CURV THRO. CURV NOR I O L MONITOR PIT.CURV NOR I O L PIT. CURV THRO.HOLD THRO.HOLD THRO. CURV IDLE I O 1 L 1 PIT. CURV IDLE I O L THRO. CURV IDLE1 I O 1 L 1 PIT. CURV IDLE1 I O L SW ON VALUE 15

17 1.2. D/R H I O L DR 45 1 AILE AILE DR SW POS/POS1 A/E/R D/R 1 D/R operation for AILE 1. Press up to select, and press to come to the interface. 2. Press up or down to select D/R, and now the shadow area is the item that can be set currently. Press to go to the next step. 3. Press A/E/R D/R to select AILE D/R, and LCD shows the corresponding AILE or AILE1 4. Press up or down to select H or L, and press INC or DEC to set the corresponding value and dual band curve will change accordingly. 5. Set AILE D/R switch on the top of the transmitter. When A/E/R D/R is in position, LCD shows AILE, and now you can set D/R value for AILE. And when A/E/R D/R is in 1 position, LCD shows AILE1, and now you can set D/R value for AILE1 6. After your setting, press EXIT to save the setting and leave the operation. H I O L DR 1 45 ELEV ELEV DR SW POS/POS1 A/E/R D/R 1 D/R operation for ELEV 1. Press up to select, and press to come to the interface. 2. Press INC or DEC to select D/R, and now the shadow area is the item that can be set currently. Press to select ELEV D/R. 3. Move up or down button to select H or L, and press INC or DEC to set the corresponding value and dual band curve will change accordingly. 4. Set ELEV D/R switch on the top of the transmitter. When A/E/R D/R is in position, LCD shows ELEV, and now you can set D/R value for ELEV. And when A/E/R D/R is in 1 position, LCD shows ELEV1, and now you can set D/R value for ELEV1 5. After your setting, press EXIT to save the setting and leave the operation. 16

18 H I O L DR 1 1 RUDD AILE DR SW POS/POS1 A/E/R D/R 1 D/R operation for RUDD 1. Press up to select, and press to come to the interface. 2. Press up or down to select D/R, and now the shadow area is the item that can be set currently. Press to go to the next step. 3. Press up or down to select H or L, and press INC or DEC to set the corresponding value and dual band curve will change accordingly. 4. Set RUDD D/R switch on the top of the transmitter. When A/E/R D/R is in position, LCD shows RUDD, and now you can set D/R value for RUDD. And when A/E/R D/R is in 1 position, LCD shows RUDD1, and now you can set D/R value for RUDD1 5. After your setting, press EXIT to save the setting and leave the operation. Remark: There is no shortcut key on the surface of the transmitter, D/R data is only one group, please be noted SUB. TRIM D/R SUB. TRIM AILE SUB. TRIM RUDD SUB. TRIM ELEV GEAR TRAVEL THRO PITH Channel neutral trim operation 1. Press up to select, and press to come to the interface. 2. Press INC or DEC to select SUB TRIM, and now the shadow area is the item that can be set currently. Press to go to the next step. 3. Press up or down to select AILE, ELEV, THRO, RUDD, GEAR, PITCH. 4. Press INC or DEC to set the value of channel neutral trim. 5. After your setting, press EXIT to save the setting and leave the operation. 17

19 1.4. TRAVEL D/R SUB. TRIM TRAVEL AILE 1 ELEV STICK: RUDD. RU TRAVEL THRO 1 1 EL Travel operation 1. Press up to select, and press to come to the interface. 2. Press up or down to select TRAVEL, and now the shadow area is the item that can be set currently. Press to go to the next step. 3. Press up or down to select the channel you like to adjust, use Rudder stick to select the high or low value. 4. Press INC or DEC to set the travel value. 5. After your setting, press EXIT to save the setting and leave the operation CH.REV CH.REV CH REV.SW CH REV.SW SWASH.MIX REV REV GYRO.SENE NOR NOR Channel reverse operation 1. Press up to select, and press to come to the interface. 2. Press up or down to select CH.REV, and now the shadow area is the item that can be set currently. Press to go to the next step. 3. Press up or down to select the channel. 4. Press INC to set the reverse mode and DEC to set normal mode. 5. After your setting, press EXIT to save the setting and leave the operation. 18

20 1.6. SWASH.MIX CH.REV SWASH.MIX GYRO.SENE SWASH.MIX AILE -5 PITH -5 ELEV -5 Swash mix (only for CCPM three servos 12 helicopter) 1. Press up to select, and press to come to the interface. 2. Press up or down to select SWASH.MIX, and now the shadow area is the item that can be set currently. Press to go to the next step. 3. Press up or down to select AILE, PITCH, ELEV. 4. Press INC or DEC to set the value of each channel. 5. After your setting, press EXIT to save the setting and leave the operation GYRO.SENS CH.REV SWASH.MIX GYRO.SENE GYRO.SENS POS -2 POS1 1 GYRO.SENS POS/POS1 GYRO.SENS 1 Gyro sensitivity adjustment 1. Press up to select, and press to come to the interface. 2. Press up or down to select GYRO.SENE, and now the shadow area is the item that can be set currently. Press to go to the next step. 3. Set GYRO.SENS switch on the top of the transmitter: When GYRO.SENS is in position, LCD shows POS, and now you can set the value for POS by INC or DEC. When GYRO.SENS is in 1 position, LCD shows POS 1, and now you can set the value for POS 1 by INC or DEC. 4. After your setting, press EXIT to save the setting and leave the operation. 19

21 1.8. THRO.CURV IDLE SW OFF IDLE SW 1 OFF/POS/POS1 NOR I O L THRO. CURV THRO. CURV IDLE1 I 2 O 8 H 1 Throttle curve operation 1. Press up to select, and press to come to the interface. 2. Press up or down to select THRO.CURV, and now the shadow area is the item that can be set currently. Press to go to the next step. 3. There are three throttle curves to be selected, normal, IDLE and IDLE 1 by the switch at the left top of the transmitter. 4. Press up or down to select the throttle curve point. There are 5 points, they are L, 1, 2, 3, H. Press INC or DEC to set the corresponding value separately, and the throttle curve will change accordingly. 5. After you setting, press EXIT to save the setting and leave the operation. Remark: the transmitter can save 3 groups of different throttle curves MONITOR THRO. CURV MONITOR PIT. CURV Monitor system 1. Press up to select, and press to come to the interface. 2. Press up or down to select MONITOR, and now the shadow area is the item that can be set currently. Press to go to the next step. 3. When you move the sticks or channel switches, you can find the corresponding channel bars will change accordingly. This function is designed to monitor the working conditions of the transmitter. 4. After your setting, press EXIT to save the setting and leave the operation. Remark: This function helps you adjust the setting, neutral trim as well as channel inspection. 2

22 1.1. PIT.CURV IDLE SW OFF IDLE SW 1 OFF/POS/POS1 NOR I O L PIT. CURV PIT. CURV IDLE1 I 2 O 2 H 1 Pitch curve 1. Press up to select, and press to come to the interface. 2. Press up or down to select PIT.CURV, and now the shadow area is the item that can be set currently. Press to go to the next step. 3. There are three pitch curves to be selected, normal, IDLE and IDLE 1 by the switch at the left top of the transmitter. 4. Press up or down to select the pitch curve point. There are 5 points, they are L, 1, 2, 3, H. Press INC or DEC to set the corresponding value separately, and the pitch curve will change accordingly. 5. After your setting, press EXIT to save the setting and leave the operation. Remark: the transmitter can save 3 groups of different pitch curves THRO.HOLD THRO.HOLD THRO.HOLD SW ON TH.HOLD POS/POS1 TH.HOLD 1 VALUE Throttle hold 1. Press up to select, and press to come to the interface. 2. Press up or down to select THRO.HOLD, and now the shadow area is the item that can be set currently. Press to go to the next step. 3. Set the TH.HOLD switch at the top of the transmitter. When TH.HOLD is in position, LCD shows SW OFF ; When TH.HOLD is in 1 position, LCD shows SW ON. Press INC or DEC to set the hold position. 4. After your setting, press EXIT to save the setting and leave the operation. 21

23 11.1. Function Menu for Fixed Wing Plane This menu includes: D/R, sub-trim, servo travel, channel reverse, stick monitor. Please see the corresponding description in the helicopter function menu for the operation. GEAR CH (Ch5) FLAP CH (Ch6) Function Menu for V-Tail V-Tail function menu includes: D/R, sub-trim, servo travel, channel reverse, monitor. Please see the corresponding description in the helicopter function menu for the operation. CH.REV MONITOR V-TAIL V-TAIL ELEV1 5 ELEV2 5 RUDD2 5 RUDD1 5 V-Tail mixing 1. Press up to select, and press to come to the interface. 2. Press up or down to select V-TAIL, and now the shadow area is the item that can be set currently. Press to go to the next step. 3. Press up or down to select ELEV1, ELEV2, RUDD1, RUDD2. And set the mixing value by INC or DEC 4. After your setting, press EXIT to save and leave the operation. 22

24 11.3. Function Menu for Delta Mix Delta mix function menu includes: D/R, sub trim, servo travel, channel reverse, monitor. Please see the corresponding description in the helicopter function menu for the operation. CH.REV MONITOR DELTA-MIXa DELTA-MIX AILE2 5 AILE1 5 ELEV1 5 ELEV2 5 Delta mix setting 1. Press up to select, and press to come to the interface. 2. Press up or down to select DELTA-MIX, and now the shadow area is the item that can be set currently. Press to go to the next step. 3. Press up or down to select AILE2, AILE1, ELEV1, ELEV2. And set the mixing value by INC or DEC 4. After your setting, press EXIT to save and leave the operation. Transmitter Model: CX-CT6C Specification: LCD Modulation: GFSK Channels: 6 Frequency: 2.4GHz Working current: 1mA Measurement: 2*185*15mm(packing meas.) 12. Technology Data Receiver Model: CX-CR6C Code format: PCM Channels: 7 Frequency: 2.4GHz DC: 4.5~9.6V, 3mA Net weight: 11.5g This device complies with part 15 of the FCC rules. Operation is subjuct to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment. Due to unforeseen changes in production procedures, the information contained in this manual is subjuct to change without notice. 23

25 Copyright 211 KY MODEL Company Limited.