ICOP-6050F Embedded 386SX PC/104 CPU Module User s Manual (Version1.1)

Transcription

1 ICOP-6050F Embedded 386SX PC/104 CPU Module User s Manual (Version1.1)

2 Copyright Notice This document is copyrighted, 2003 by ICOP Technology Inc. All rights are reserved. The information in the manual is subject to change without notice in order to improving products. No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of the manufacturer. ICOP Technology Inc. assumes no responsibility for any inaccuracies that may be contained in this document. ICOP Technology Inc. makes no commitment to update or to keep current the information contained in this manual. Copyright 2000 by ICOP Technology Inc. All rights reserved. Ver , Printed in Taiwan Trademarks Acknowledgments All brand names and trademarks are the properties and registered brands of their respective owners. ii

3 T a b l e o f C o n t e n t s iii C h a p t e r 0 Startup Packing List Specifications Component Location... 3 C h a p t e r 1 Introduction Features Specifications DiskOnChip 2000 Flash Disk... 7 C h a p t e r 2 Installation Jumper Settings Connectors DiskOnChip/Flash ROM Disk Watchdog Timer...14 Appendix A Pin Assignments 22 IDE Interface Connector Floppy Disk Connector Parallel Port Interface bit General Purpose I/O Serial Port Interface Keyboard and PS/2 Mouse Connector PC/104 Connectors Warranty 28 iii

4

5 0.1 Packing List C h a p t e r 0 Startup Product Name ICOP-6050F Function Embedded 386SX PC/104 CPU Module Package ICOP-6050F Embedded 386SX PC/104 CPU Module FDD cable x 1 HDD cable x 1 GPIO cablex 1 RS232 cable x 2 Printer cable x 1 AT KB connector cable x 1 ICOP Embedded 386SX PC/104 AIO CPU Module User's Manual 1

6 0.2 Specifications Features ICOP-6050F Chipset DM&P(ALi) M6117D Processor 386SX-45 on-die Multi I/O Chip ALi 5113 BIOS AMI BIOS Watchdog Timer From 30.5μs to 512 seconds Bus Interface RAM PC/104 standard compliant 8MB onboard Enhanced IDE Port 1 Floppy Connector 1 Flash Disk / 1 DiskOnChip Socket Serial Port RS232 X 2 Parallel Port 1 Power Requirement Board Weight 76g Board Size 90mm x 96mm 2 ICOP Embedded 386SX PC/104 AIO CPU Module User's Manual

7 0.3 Component Location ICOP-6050F Reset COM2 RS232/RS485 FDD Cont. COM1 sel. for COM2 Mouse Keybboard LPT Port EIDE Port GPIO port RS-485 HDD-LED +5V / GND GND/-5V/-12V/+12V PC/104 port ICOP Embedded 386SX PC/104 AIO CPU Module User's Manual 3

8 C h a p t e r 1 Introduction 1.1 Features PC/104 (96x90 mm) Embedded CPU Module PC/104 connector DM&P (ALi) M6117D Embedded CPU, 100% compatible with 386SX CPU 8MB EDO RAM onboard Enhanced IDE devices and FDD interface One Bi-directional Parallel Port RS-232 interface RS-232/485 interface Watchdog timer Socket for Flash or DiskOnChip Onboard Keyboard, Mouse header Single voltage +5 V power connector Operating temperature from 20 ~ +70 Flexible OEM/ODM design 4 ICOP Embedded 386SX PC/104 AIO CPU Module User's Manual

9 1.2 Specifications Embedded CPU: DM&P(ALi) M6117D is an implementation of an INTEL compatible 386SX CPU, Realtime clock, a watchdog timer and ALi s M1217B chipset BIOS: Y2K compliant AMI system BIOS DRAM Memory: 8MB EDO DRAM onboard Bus Interface: PC/104 Data Bus: 16-bit Bus Speeds: PC/104-8 MHz (above values are defaults, bus speeds are programmable up to 16 MHz) DMA Channels: 7 Interrupt Levels: 15 Enhanced IDE: supports one port and up to two hard drives or Enhanced IDE devices of PIO mode 4. BIOS enabled/disabled Watchdog Timer: generates either a RESET, NMI or an IRQ when your application loses control over the system. Optionally the watchdog can trigger a user specified interrupt. The watchdog is configurable from 30.5μs to 512 seconds (in 30.5μs segments) Real-time Clock: included in M6117D with onboard lithium battery backup for 10 years of data retention. CMOS data backup of BIOS setup and BIOS default. Keyboard and Mouse Connectors: Internal 5-pin header for AT-keyboard Internal 5-pin header for PS/2-mouse High Speed Multi I/O Chipset: ALi 5113 or SMS CFDC37C669 Serial ports: one high speed RS-232 port, one high speed RS-232/485 port (jumper selectable). Both with 16C550 UART and 16 byte FIFO. BIOS enabled/ disabled Floppy Disk Drive Interface: supports up to two floppy drives, 5¼ (360 KB or 1.2 MB) and 3½ (720 KB, 1.44 MB). BIOS enabled / disabled Bi-directional Parallel Port: supports SPP, EPP and ECP mode. BIOS ICOP Embedded 386SX PC/104 AIO CPU Module User's Manual 5

10 enabled/disabled Environmental and Power Power Requirements: single voltage +5 V Board Dimensions: 90 (L) x 96 (W) mm. Board Weight: 76 g Extended Operating Temperature: -20~+70 C Storage Temperature: 0~+60 C 6 ICOP Embedded 386SX PC/104 AIO CPU Module User's Manual

11 1.3 DiskOnChip 2000 Flash Disk Flash Disk DiskOnChip 2000 Package: Single Chip FlashDisk in 32-pin DIP JEDEC Capacity: 8-256MByte capacity Data Reliability: ECC/EDC error correction Memory Window: 8 KByte ICOP Embedded 386SX PC/104 AIO CPU Module User's Manual 7

12 C h a p t e r 2 Installation 2.1 Jumper Settings J1 J15 J14 J10 J16 J2 J3 J8 J12 J13 J11 J9 J 6 J7 J4 +5V 8 ICOP Embedded 386SX PC/104 AIO CPU Module User's Manual

13 ICOP-6050F J1 J6 J7 RESET Switch +5V / Ground Power connector (Reserved): This 4 pin connector link to the +12V,-12V,-5V and GND pins of PC/104 connector. In case if you need +12,-12V or -5V for external device, you can use this connector. The power should supply by the PC/104 bus. Pin 1: +12V Pin 2: -12V Pin 3: -5V Pin 4: GND J9 HDD LED J10 RS-232/485 selection for COM2 1-2: RS-232 mode 2-3: RS-485 mode ICOP Embedded 386SX PC/104 AIO CPU Module User's Manual 9

14 2.2 Connectors J2 J3 J4 J7 J8 J11 J12 J13 J14 J15 J16 Keyboard connector Mouse connector PC104 port GND/-5/-12/+12 Printer port COM2 RS-485 EIDE Port GPIO (16-bit Gerenal Purpose Input Output) COM 1 RS-232 COM 2 RS-232 FDD controller 10 ICOP Embedded 386SX PC/104 AIO CPU Module User's Manual

15 2.3 DiskOnChip/Flash ROM Disk Setup a DiskOnChip 2000 Flash Disk Installation Instructions 1. Make sure the ICOP-6050 is powered OFF 2. Plug the DiskOnChip 2000 device(s) into its socket. Verify the direction is correct (pin 1 of the DiskOnChip 2000 is aligned with pin 1 of the socket) 3. Set address for both DiskOnChip and Flash Disk devices as below instructions: Step1: Enter to AMI BIOS Setup Utility while system power on Step2: Enter to Advanced Chipset Setup Step3: Select GPCS Function to Enable (For DiskOnChip) Step4: Setect GPCS0 Command to MEMR/W 8bit Step5: Select GPCS0 Start Address to 0C8000 HEX Step6: Select GPCS0 Size to 8 KBYTE (goto Step 10) (For Flash Disk) Step4: Setect GPCS0 Command to MEMR/W 8bit Step5: Select GPCS0 Start Address to 0E0000 HEX Step6: Select GPCS0 Size to 64 KBYTE Step7: Save changed and exit. 4. Power up the system 5. During power up you may observe the messages displayed by the DiskOnChip 2000 when its drivers are automatically loaded into system s memory 6. At this stage the DiskOnChip 2000 can be accessed as any disk in the system 7. If the DiskOnChip 2000 is the only disk in the system, it will appear as the first disk (drive C: in DOS) 8. If there are more disks besides the DiskOnChip 2000, the DiskOnChip 2000 will appear by default as the last drive, unless it was programmed as first drive. (please refer to the DiskOnChip 2000 utilities user manual) 9. If you want the DiskOnChip 2000 to be bootable: a - copy the operating system files into the DiskOnChip by using the standard DOS command (for ICOP Embedded 386SX PC/104 AIO CPU Module User's Manual 11

16 example: sys d:) b - The DiskOnChip should be the only disk in the systems or should be configured as the first disk in the system (c: ) using the DUPDATE utility For more information on DiskOnChip2000 technology, visit M-Systems Web site where you can find Utilities Manual, Data Sheets and Application Notes. In addition, you can find the lasted DiskOnChip 2000 S/W Utilities. 12 ICOP Embedded 386SX PC/104 AIO CPU Module User's Manual

17 2.3.2 Setting up a Flash Disk Before you can use the ICOP-6050F s Flash disk you will have to initialize it using a software utility called PC104.EXE. This program can be found on the utility disk in the subdirectory A:\FLASH - Connect a keyboard and floppy disk ICOP-6050F to the PC/104 bus and boot-up your system. - run PC104.EXE (this is a DOS command line utility) ICOP-6050F FLASH disk initialize program V1.0 FLASH manufacturer : (1)ATMEL (2)SST Input manufacturer number (1,2) : 1 Input quantity of FLASH (1,2) : 2 Simulation disk: (1)DISK-A (2)DISK-B (3)DISK-C (4)DISK-D Input manufacturer number (1,2,3,4) : 1 FLASH-DISK initialize finish. (Text in bold should be entered by user) - After running the PC104.EXE configuration program reboot the system, while holding down the left Ctrl key. This will bring you to the Flash Disk Utility - CHANGE CURRENT DISK NUMBER lets you select the drive you want to assign to the disk, either A, B, C or D - CHANGE FLASH DISK SIZE lets you select the amount of Flash EPROM chips that are onboard. - make selections and reboot the system after closing the program Your disk can now be formatted and setup with normal DOS commands such as FORMAT, FDISK, COPY, SYS etc. Note : when assigning the solid state disk as either C or D, you first have to run FDISK before formatting the drive! ICOP Embedded 386SX PC/104 AIO CPU Module User's Manual 13

18 2.4 Watchdog Timer The watchdog timer uses a KHz frequency source with a 24-bit counter. Its time range stretches from 30.5 ms to 512 sec. with a resolution of 30.5 ms. When the watchdog times out a System RESET, NMI or IRQ can be invoked. Watchdog timer control and the 24-bit counter itself occupy 6 consecutive 8-bit address locations. When functioning properly the system resets the watchdog timer periodically to prohibit that it times out. If the watchdog timer times out, it will RESET the system, or generate and NMI or IRQ, depending on its configuration. Watchdog or System Timer Another great application is to generate a periodic IRQ signal. Under DOS environment, the 8254, system timer 0, will generate IRQ0 every 54.9 ms. The watchdog is like system timer 0. It can be programmed to periodically generate a configurable IRQ. It may be clear that the selected IRQ, will be no longer available to the system. Configuring the Watchdog Timer in the BIOS The M6117D watchdog configuration register can be controlled by software or can be setup in the BIOS. To do so go to BIOS Setup s Advanched Chipset Setup Watchdog Function = Enable/Disable Watchdog Signal = RESET, NMI or IRQ 3/4/5/6/7/9/10/11/12/14/15 Watchdog Timer = 1/2/4/8/16/32/64/128/256/512 Seconds The BIOS setup only offers a limited amount of time-out values. More a hiher resolution of timeout values refer to the next paragraph Configuring the Watchdog Timer by Software Note that in case of using the BIOS setup, the watchdog starts counting the moment it passes the BIOS setup. This means that if you set the time-out period to 1 second, the system will keep rebooting before being able to load operating system or software! After you have finnished configuring you watchdog timer read Timeout Status & Reset - INDEX 3CH on page 12 and look at the example on page 15 to find out how to priodically reseting the timeout status to prevent the 14 ICOP Embedded 386SX PC/104 AIO CPU Module User's Manual

19 watchdog timer from invoking a RESET, NMI or IRQ. Configuring the Watchdog Timer by Software Chipset configuration registers The M6117D configuration register INDEX 37H, 38H, 39H, 3AH, 3BH, 3Ch are used to control the watchdog functions and/or display its current status. Enable/Disable watchdog - INDEX 37H Bit Value Action 7 reserved Do not modify the value of these bits! Disable watchdog timer Enable watchdog timer 5-0 Other function Do not modify the value of these bits! Watchdog time out action - INDEX 38H Bit Value Action No output signal 0001 IRQ IRQ IRQ IRQ IRQ IRQ IRQ IRQ IRQ IRQ IRQ NMI 1101 System RESET 1110 No output signal ICOP Embedded 386SX PC/104 AIO CPU Module User's Manual 15

20 1111 No output signal 3-0 Other function Do not modify the value of these bits! Watchdog timer - INDEX 39H, 3AH, 3BH Index 3Bh 3Ah 39h Bits D7 D0 D7 D0 D7 D0 counter For example [VSB......LSB] Index 3Bh 3Ah 39h Time out 00h 00h 01h 30.5μs 00h 00h 02h 61μs 00h 01h 00h 7.8 ms 00h 02h 00h 15.6 ms 01h 00h 00h 2 s 02h 00h 00h 4 s FFh FFh FFh 512 s Timeout Status & Reset - INDEX 3CH Bit Value Action Timeout has not occurred Timeout has occured Reset timer Has no meaning 5-0 Other function, do not modify these bits Programming the watchdog To perform any operation on the M6117D configuration registers you always have to unlock first and lock the registers afterwards 16 ICOP Embedded 386SX PC/104 AIO CPU Module User's Manual

21 Unlock configuration register mov al, 013h out 22h, al mov al, 0c5h out 23h, al Lock configuration register mov al, 013h out 22h, al mov al, 000h out 23h, al Read the value of a configuration register For example, read INDEX 3Ch : Unlock configuration register mov al, 03ch out 22h, al in al, 23h push ax Lock configuration register pop ax ;AL - result Write data to configuration register For example, write 0FFh to INDEX 3Bh : Unlock configuration register mov al, 03bh out 22h, al ICOP Embedded 386SX PC/104 AIO CPU Module User's Manual 17

22 mov al, 0ffh out 23h, al Lock configuration register Watchdog Program Example We use the following sequence to initialize the watchdog timer: (1) Unlock configuration register. (2) Disable watchdog timer by setting INDEX 37H Bit 6 to 0. (3) Set the expected counter value to INDEX 3BH, 3AH, 39H. (4) Select timeout action from INDEX 38H Bit 7-4. (5) Enable watchdog timer by setting INDEX 37H Bit 6 to 1. (6) Lock configuration register. Example: Set timeout to 128 sec to generate a system RESET. ; Please use MASM to compiler the following program ; Execute under DOS environment dosseg. model small. stack 100h.code main proc mov ax, 0c513h ; Unlock config. register call writechip mov ax, 03737h ; Disable watchdog timer call readchip and al, b xchg ah, al call writechip 18 ICOP Embedded 386SX PC/104 AIO CPU Module User's Manual

23 mov ax, 0403bh ; Set the expected counter ; value call writechip ; to [400000h] mov ax, 0003ah ; 30.5*sec*400000h= 128 sec call writechip mov ax, 00039h call writechip mov ax, 03838h ; Select system reset as ; timeout action call readchip and al, b or al, b xchg ah, al call writechip mov ax, 03737h ; Enable watchdog timer call readchip or al, b xchg ah, al call writechip mov ax, 00013h ; Lock config. register call writechip mov ax, 04c00h int 21h main endp readchip proc out 22h, al in al, 23h ICOP Embedded 386SX PC/104 AIO CPU Module User's Manual 19

24 ret readchip endp writechip proc out 22h, al xchg ah, al out 23h, al xchg ah, al ret writechip endp end main Reset watchdog timer Resets the watchdog timer periodically to prevent timeout. mov ax, 0c513h ; Unlock configuration ; register call writechip mov ax, 03C3Ch ; Reset watchdog timer ; counter call readchip or al, ; The counter is reset at xchg ah, al ; out 23h, al call writechip mov ax, 00013h ; Lock configuration 20 ICOP Embedded 386SX PC/104 AIO CPU Module User's Manual

25 ; register call writechip (the above code uses readchip and writechip procedures) ICOP Embedded 386SX PC/104 AIO CPU Module User's Manual 21

26 IDE Interface Connector Appendix A Pin Assignments Pin Description Pin Description 1 Reset 2 GND 3 Data 7 4 Data 8 5 Data 6 6 Data 9 7 Data 5 8 Data 10 9 Data 4 10 Data Data 3 12 Data Data 2 14 Data Data 1 16 Data Data 0 18 Data GND 20 N/C 21 N/C 22 GND 23 IOW # 24 GND 25 IOR # 26 GND 27 N/C 28 BALE-Default 29 N/C 30 GND-Default 31 Interrupt 32 IOCS16-Default 33 SA1 34 N/C 35 SA0 36 SA2 37 HDC CS0 38 HDC CSI # 39 HDD Active 40 GND 22 ICOP Embedded 386SX PC/104 AIO CPU Module User's Manual

27 Floppy Disk Connector Pin Description Pin Description 1 GND 2 Drive Enable Select 3 GND 4 N/C 5 GND 6 N/C 7 GND 8 Index # 9 GND 10 Drive select 0 11 GND 12 Drive select 1 13 GND 14 Drive select 2 15 GND 16 Motor enable 17 GND 18 Direction # 19 GND 20 STEP # 21 GND 22 Write data # 23 GND 24 Write gate # 25 GND 26 Track 0 # 27 GND 28 Write protect # 29 GND 30 Read data # 31 GND 32 Side 1 select # 33 GND 34 Disk change # ICOP Embedded 386SX PC/104 AIO CPU Module User's Manual 23

28 Parallel Port Interface Pin Description Pin Description 1 Strobe 2 Data 0 3 Data 1 4 Data 2 5 Data 3 6 Data 4 7 Data 5 8 Data 6 9 Data 7 10 Acknowledge # 11 Busy 12 Paper Empty # 13 Printer Select 14 Auto Form Feed # 15 Error # 16 Initialize # 17 Printer Select In # 18 GND 19 GND 20 GND 21 GND 22 GND 23 GND 24 GND 25 GND 26 NC 16-bit General Purpose I/O Pin Description Pin Description 1 GND 2 Vcc 3 GP0 4 GP8 5 GP1 6 GP9 7 GP2 8 GP10 9 GP3 10 GP11 11 GP4 12 GP12 13 GP5 14 GP13 15 GP6 16 GP14 17 GP7 18 GP15 19 Vcc 20 GND 24 ICOP Embedded 386SX PC/104 AIO CPU Module User's Manual

29 Serial Port Interface 10- Pin D-Type Description 1 1 Data Carrier Detect (DCD)/5V/12V 2 2 Receive Data (RXD) 3 3 Transmit Data (TXD) 4 4 Data Terminal Ready (DTR) 5 5 Ground (GND) 6 6 Data Set Ready (DSR) 7 7 Request to Send (RTS) 8 8 Clear to Send (CTS) 9 9 Ring Indicator (RI)/5V/12V 10 X NC Keyboard and PS/2 Mouse Connector Clock Data No Connection GND Power Note for Keyboard: Pin1: KBCLK Pin2: KBDATA Clock Data No Connection GND Power Note for Mouse: Pin1: MCLK Pin2: MDATA ICOP Embedded 386SX PC/104 AIO CPU Module User's Manual 25

30 PC/104 Connectors 64-Pin Long Connector PIN No. PIN Name PIN No. PIN Name 1 IOCHCHK * 2 0V 3 SD7 4 RESETDRV 5 SD6 6 +5V 7 SD5 8 IRQ9 9 SD4 10-5V 11 SD3 12 DRQ2 13 SD V 15 SD1 16 ENDXFR * 17 SD V 19 IOCHRDY 20 (KEY) 21 AEN 22 SMEMW * 23 SA19 24 SMEMR * 25 SA18 26 IOW * 27 SA17 28 IOR * 29 SA16 30 DACK3 * 31 SA15 32 DRQ3 33 SA14 34 DACK1 * 35 SA13 36 DRQ1 37 SA12 38 REFRESH * 39 SA11 40 SYSCLK 41 SA10 42 IRQ7 43 SA9 44 IRQ6 45 SA8 46 IRQ5 47 SA7 48 IRQ4 49 SA6 50 IRQ3 51 SA5 52 DACK2 * 53 SA4 54 TC 55 SA3 56 SALE 57 SA V 59 SA1 60 OSC 61 SA0 62 0V 63 0V 64 0V 26 ICOP Embedded 386SX PC/104 AIO CPU Module User's Manual

31 40-Pin Short Connector PIN No. PIN Name PIN No. PIN Name 1 0V 2 0V 3 MEMCS16 * 4 SBHE * 5 IOCS16 * 6 LA23 7 IRQ10 8 LA22 9 IRQ11 10 LA21 11 IRQ12 12 LA20 13 IRQ15 14 LA19 15 IRQ14 16 LA18 17 DACK0 * 18 LA17 19 DRQ0 20 MEMR * 21 DACK5 * 22 MEMW * 23 DRQ5 24 SD8 25 DACK6 * 26 SD9 27 DRQ6 28 SD10 29 DACK7 * 30 SD11 31 DRQ7 32 SD V 34 SD13 35 MASTER * 36 SD V 38 SD V 40 (KEY) ICOP Embedded 386SX PC/104 AIO CPU Module User's Manual 27

32 Warranty This product is warranted to be in good working order for a period of one year from the date of purchase. Should this product fail to be in good working orderat any time during this period, we will, at our option, replace or repair it at noadditional charge except as set forth in the following terms. This warranty doesnot apply to products damaged by misuse, modifications, accident or disaster. Vendor assumes no liability for any damages, lost profits, lost savings or anyother incidental or consequential damage resulting from the use, misuse of, orinability to use this product. Vendor will not be liable for any claim made by anyother related party. Return authorization must be obtained from the vendor before returned merchandise will be accepted. Authorization can be obtained by calling or faxing the vendor and requesting a Return Merchandise Authorization (RMA) number. Returned goods should always be accompanied by a clear problem description. 28 ICOP Embedded 386SX PC/104 AIO CPU Module User's Manual