Mity SoC Module & Mity SoC Development Kit
|
|
|
- Todd Malone
- 8 years ago
- Views:
Transcription
1 Mity SoC Module & Mity SoC Development Kit Mity SoC Module with 2MB/2S/IDE/Parallel/GPIO & ISA bus Development for Mity SoC Module User s Manual (Revision1.0)
2 Copyright The information in this manual is subject to change without notice for continuous improvement in the product. All rights are reserved. The manufacturer assumes no responsibility for any inaccuracies that may be contained in this document. And makes no commitment to update or to keep current the information contained in this manual. Manual No. IUM Ver.1.0 All rights reserved. 1 st issue date: October 25, 2002 Released date: January 13, 2003 Trademarks Acknowledgment Other brand names or product names appearing in this document are the properties and registered trademarks of their respective owners. All names mentioned herewith are served for identification purpose only. ii
3 T a b l e o f C o n t e n t s T a b l e o f C o n t e n t s...iii C h a p t e r 0 Startup 0.1 Packing List Option Accessory Specification... 2 Mity SoC Module... 2 Mity Soc Development Board Ordering Information Ordering Selection... 5 C h a p t e r 1 Introduction 1.1 Features... 7 Mity SoC Module... 7 Mity Soc Development Board Specification... 8 Mity SoC Module... 8 Mity Soc Development Board VGA Interface DiskOnChip 2000 Flash Disk Network Interface C h a p t e r 2 Installation 2.1 Board Outline Mity SoC Module Mity Soc Development Board Mity SoC Development Kit Installation Connectors & Jumpers Summary Mity SoC Module Mity Soc Development Board Pin Assignments & Jumper Settings iii
4 iv Mity SoC Module J1 : X-ISA Connector J2 : I/O Connector U2 : DRAM 2MB (Option) U3 : DRAM 2MB (Standard) u8 : BIOS Mity Soc Development Board J1 : X-ISA Connector J2 : ISA bus Connector, SL J3 : ISA bus Connector, SL J4 : PC/104 Connector CN J4 : PC/104 Connector CN J6 : Mity-Mite VGA J7 : IDE Connector J8 : I/O Connector J9 : GPIO J10 : COM J11 : COM J12 : RESET J13 : PS/2 Keyboard J14 : VGA J15 : DC_INPUT (Terminal Block) J16 : DC_JACK J17 : DC_INPUT (Molex) J18 : Mity-Mite VGA J19 : Keyboard J20 : PRINT : LED Display U2 : DOC Connector (DiskOnChip) U5 : 8ØPORT (7 Segment Display) DiskOnChip/Flash ROM Disk Setup a DiskOnChip 2000 Flash Disk Watchdog Timer C h a p t e r 3 SVGA Setup 3.1 Introduction Chipset Display memory... 43
5 3.2 Flat Panel BIOS and Wiring C h a p t e r 4 Network Interface 4.1 Introduction Software Support a p p e n d i x : schematic diagram..53 W a r r a n t y...53 Mity Soc CPU Module : Mity SoC Module 2MB//2MB/2S/IDE/Parallel/GPIO v
6 vi This page is intentionally left blank.
7 C h a p t e r Packing List Startup Product Function Package Mity SoC Module Mity SoC Development Kit Mity SoC Module with 2MB/2S/IDE/ Parallel/GPIO ISA bus Development Board for Mity SoC Module Mity SoC Module x1 ISA bus Development Board x1 Manual & Drivers CD x 1 FDD cable x 1 HDD cable x 1 VGA cable x1 RS232 cable x 2 Printer cable x 1 GPIO cable x1 Keyboard cable x1 0.2 Option Accessory Product Function Package Mity Mite VGA/LCD DevKit VGA/LCD Control Module Mity-Mite VGA/LCD Development Kit x1 Mity Soc CPU Module : Mity SoC Module 2MB//2MB/2S/IDE/Parallel/GPIO 1
8 0.3 Specification Mity SoC Module Mity SoC CPU Module 2MB/2S/IDE/Parallel/GPIO SoC BIOS System Memory Bus Interface I/O Interface ISA Interface Connectors H/W & S/W Support Power Requirement Board Weight Board Size Operating Temperature DM&P(ALi) M6117D 386SX System-on-Chip CPU 40MHz Data Bus: 16-bit Bus Speeds: 8MHz, programmable up to 16MHz Watchdog Timer: 30.5uS to 512uS Real Time Clock (Need external Battery) AMI BIOS (Flash disk or optional EPROM) Onboard 2MB (optional 4MB) 16-bits ISA Interface RS-232 pin x2 (optional TTL level) Bi-directional Parallel interface x1 16-bit GPIO interface Keyboard interface IDE interface Speaker Power LED DM&P(ALi) M6117D 386SX SoC Support Mity-Mite VGA 2.0mm, 32x2 pin header for specific I/O Interface x1 2.0mm, 32x2 pin header for specific X-ISA 16-bit Interface x1 DMP Software Library Support Development Kit Support Single Voltage 45g 65mm X 45mm (2.56 x 1.77 inches) -20 o C ~ +70 o C 2 Mity Soc CPU Module : Mity SoC Module 2MB/2S/IDE/Parallel/GPIO
9 Mity SoC Development Board Mity-SoC ISA bus Development board Board Type Bus Interface I/O Interface ISA Interface Connectors LED Indicators Half-size ISA-bus Extended I/O Module for Mity-SoC PC/ bits ISA Interface RS-232 pin x2 (optional TTL level) Bi-directional Parallel interface x1 16-bit GPIO interface Keyboard interface IDE interface Speaker Power LED DM&P(ALi) M6117D 386SX SoC Support Mity-Mite VGA 2.0mm, 32x2 pin header for Mity-SoC x2 2.0mm, 32x1 pin header for Mity-Mite VGA/LCD Module x1 40-pin box header for enhanced IDE x1 20-pin box header for GPIO x1 26-pin box header for printer x1 10-pin box header for COM2 5-pin header for PS/2 keyboard x1 10-pin box header for VGA x1 PC/104 connector x1 32-pin socket for for DiskOnChip x1, 8MB~256MB External 9-pin D-Sub male COM1 connector External 15-pin D-type female VGA connector External 6-pin Mini DIN for PS/2 KB Power input x3 selection: (1)DC Jack, (2)2-pin Terminal strip and (3) 4-pin Molex connector P.O.S.T.Test Indicator : Two digit 7-Segment LED Display GPIO Input LED indicators x16 GPIO Switch Input x4 IDE LED DiskOnChip One socket supporting DiskOnChip 8MB~256MB (User GPSC) Mity Soc CPU Module : Mity SoC Module 2MB//2MB/2S/IDE/Parallel/GPIO 3
10 0.3 Specification continuation H/W & S/W Support Power Requirement Board Weight Board Size Operating Temperature DMP Software Library Support Development Kit Support Single Voltage 225g 185mm X 122mm (7.28 x 4.80 inches) -20 o C ~ +70 o C 0.4 Ordering Information Mity SoC-8/P5 Mity SoC-12/P5 Mity-Mite VGA/LCD Development Kit Mity-SoC Development Board Mity-SoC Development Kit 5-Pack of Mity-Mite Module 2MB/2S/IDE/Parallel/ GPIO (TTLx1, RS232 x1) 5-Pack of Mity-Mite Module 4MB/2S/IDE/Parallel/ GPIO (TTLx2) VGA/LCD Development kit for Mity SoC and Mity-Mite Module ISA bus Development board for Mity-SoC Module Complete Development Kit with Mity-SoC module, Mity-Mite VGA/LCD module and ISA Development board. 4 Mity Soc CPU Module : Mity SoC Module 2MB/2S/IDE/Parallel/GPIO
11 0.5 Ordering Selection Mity Soc CPU Module : Mity SoC Module 2MB//2MB/2S/IDE/Parallel/GPIO 5
12 This page is intentionally left blank. 6 Mity Soc CPU Module : Mity SoC Module 2MB/2S/IDE/Parallel/GPIO
13 C h a p t e r 1 Introduction 1.1 Features Mity SoC Module Mity size CPU Module (65 x 45 mm) DM&P M6117D 386SX System-On-Chip Onboard 2MB SDRAM (optional 4MB) Enhanced IDE devices interface One Bi-directional Parallel Port RS-232/485 interface x2 Watchdog timer Support Keyboard interface Single voltage +5 V power connector Operating temperature from 20 C +70 C DM&P H/W & S/W Library support Development kit support Accept custom modification Provide OEM & ODM design Mity-SoC Development Board Base board development concept for Mity-SoC Provide quick time-to-market I/O integration ISA-bus interface Expandable PC/104 interface Available socket for DiskOnChip Onboard Keyboard & Mouse connector Mity Soc CPU Module : Mity SoC Module 2MB//2MB/2S/IDE/Parallel/GPIO 7
14 1.2 Specification Mity SoC Module Embedded CPU: DM&P M6117D 386SX System-on-Chip CPU 40MHz, Realtime clock, and watchdog timer. BIOS: Y2K compliant AMI system BIOS System Memory: Onboard 2MB SDRAM (optional 4MB) Data Bus: 8/16-bit Bus Speeds: ISA Bus 40MHz DMA Channels: 7 Interrupt Levels: 15 Enhanced IDE: supports one port and up to two hard drives or Enhanced IDE devices of PIO mode 4. BIOS enabled/disabled Watchdog Timer: generates either a RESET, NMI or an IRQ when your application loses control over the system. Optionally the watchdog can trigger a user specified interrupt. The watchdog is configurable from 30.5µs to 512 seconds (in 30.5µs segments) Keyboard Connector: supports PS/2 Keyboard Serial ports: supports high speed RS-232 port, high speed RS-232/485 port Bi-directional Parallel Port: supports SPP, EPP and ECP mode. BIOS enabled/disabled Environmental and Power Power Requirements: single voltage mA Board Dimensions: 65 (L) x 45 (W) mm. Board Weight :45 g Extended Operating Temperature: -20 C ~+70 C 8 Mity Soc CPU Module : Mity SoC Module 2MB/2S/IDE/Parallel/GPIO
15 Mity-SoC Development Board Bus Interface: ISA Bus Interface I/O Expansion: PC/104 ISA Bus Interface I/O Interface: provides headers for IDE, Serial, Parallel, GPIO, and Speaker. Board Testing : provides P.O.S.T. Test during design test Disk-On-Chip : supports 8~256MB Real-time Clock: included in DM&P M6117D SOC with onboard lithium battery backup for 10 years of data retention. CMOS data backup of BIOS setup and BIOS default. Environmental and Power Power Requirements: single voltage mA Board Dimensions: 65 (L) x 45 (W) mm. Board Weight :45 g Extended Operating Temperature: -20 C ~+70 C Mity Soc CPU Module : Mity SoC Module 2MB//2MB/2S/IDE/Parallel/GPIO 9
16 1.3 VGA Interface Chipset: TOPRO TP6508IQ Chip Memory: Shared system memory up to 128MB System Bus: 16bit ISA bus Panel Data Bus: 24-bit Display: CRT and LCD Flat Panel, Mono/TFT/DSTN/LCD Supported Flat Panels: NEC NL-6448AC30-10 TFT 9.4" 640X480 NEC NL-6448AC30-03 TFT 9.4" 640X480 NEC NL-6448AC33-10 TFT 10.4" 640X480 NEC NL-6448AC33-13 TFT 10.4" 640X480 NEC NL-6448AC33-18 TFT 10.4" 640X480 NEC NL-8060BC31-09 TFT X600 NEC NL-8060AC31-02 TFT 10.4" 800X600 NEC NL-8060AC31-01 TFT 10.4" 800X600 SHARP LQ10D42 TFT 10.4" 640X480 SHARP LQ10D421 TFT 10.4" 640X480 SHARP LQ12531 TFT 12.1" 800x600 SHARP LM64C35P MONO 10.4" 640X480 Planar EL AA1 EL color 10.4" 640X Mity Soc CPU Module : Mity SoC Module 2MB/2S/IDE/Parallel/GPIO
17 1.4 DiskOnChip 2000 Flash Disk Flash Disk DiskOnChip 2000 Package: Single Chip FlashDisk in 32-pin DIP JEDEC Capacity: MByte capacity Data Reliability: ECC/EDC error correction Memory Window: 8 Kbyte 1.5 Network Interface Chipset: Realtek 8019AS single chip Type: 10BASE-T Connectors: 8-pin male header, pitch 2.0mm Monitoring LEDs: network ready indicator, network activity indicator Compatibility: NE2000 Mity Soc CPU Module : Mity SoC Module 2MB//2MB/2S/IDE/Parallel/GPIO 11
18 C h a p t e r 2 Installation 2.1 Board Outline Mity SoC Module Mity SoC Development Board 12 Mity Soc CPU Module : Mity SoC Module 2MB/2S/IDE/Parallel/GPIO
19 Mity Mite VGA/LCD Development Board 2.2 Mity SoC Development Kit Installation Warning : Be sure that you have the right orientation of Mity SoC Module before plugging it into the ISA Bus & I/O headers of the Mity SoC Development Board. Take note that the CPU DMP M6117D must be situated on the right side. The Manufacturer is not liable for any damage caused by wrong orientation. Mity Soc CPU Module : Mity SoC Module 2MB//2MB/2S/IDE/Parallel/GPIO 13
20 2.3 Connectors & Jumpers Summary Mity SoC Module SUMMARY J1: ISA x2 Pin Header J2: I/O x2 Pin Header U2: DRAM 2MB (Option) 42-pin DIP SSD U3: DRAM 2MB (Standard) 42-pin DIP SSD U8: BIOS 32-pin PLCC Socket 14 Mity Soc CPU Module : Mity SoC Module 2MB/2S/IDE/Parallel/GPIO
21 Mity SoC Development Board SUMMARY J1: Mity SoC x2 Pin Header J2: ISA bus Connector, SL62 62-pin Gold finger (Total 98 pins) J2: ISA bus Connector, SL36 36-pin Gold finger (Total 98 pins) J4: PC104 Connector 104-pin Female Box Header J6: Mity-Mite VGA x2 Pin Header J7: IDE Connector 40-pin Box Header J8: I/O x2 Pin Header J9: GPIO 20-pin Box Header J10: COM1 9-pin D-Sub Connector J11: COM2 10-pin Box Header J12: RESET 2-pin Pin Header J13: PS/2 Keyboard 6-pin Mini Din Connector J14: VGA 15-pin D-Sub Connector J15: DC_INPUT 2-pin Pin Header J16: DC_JACK 3-pin Jack J17: DC_INPUT 4-pin Pin Header J18: Mity-Mite VGA pin Box Header J19: Keyboard pin Molex Header J20: PRINT 26-pin Box Header LED Display Green LED x16 U2: DOC Connector (DiskOnChip) 32-pin DIP Socket U5: 8 PORT (7 Segment Display) 18-pin DIP SSD Mity Soc CPU Module : Mity SoC Module 2MB//2MB/2S/IDE/Parallel/GPIO 15
22 2.4 Pin Assignments & Jumper Settings Mity SoC Module J1: X-ISA Connector x2-Box Header 1 GND 2 SBHE 3 RSTDRV 4 SD7 5 VCC 6 SD6 7 SD8 8 SD5 9 SD9 10 SD4 11 SD10 12 SD3 13 SD11 14 SD2 15 SD12 16 SD1 17 SD13 18 SD0 19 GND 20 IOCHRDY 21 SMEMW 22 AEN 23 SMEMR 24 SA19 25 XIOW 26 SA18 27 XIOR 28 SA17 29 SD14 30 SA16 31 SD15 32 SA15 33 MEMCS16 34 SA14 35 TOCS16 36 SA13 37 REFRESH 38 SA12 39 SYSCLK 40 SA11 41 IRQ7 42 SA10 43 IRQ6 44 SA9 45 IRQ5 46 SA8 47 IRQ4 48 SA7 49 IRQ3 50 SA6 51 IRQ10 52 SA5 53 IRQ11 54 SA4 55 BALE 56 SA3 57 VCC 58 SA2 59 XOSC 60 SA1 61 GND 62 SA0 63 IRQ12 64 IRQ14 16 Mity Soc CPU Module : Mity SoC Module 2MB/2S/IDE/Parallel/GPIO
23 J2: I/O Connector x2-Box Header 1 DCD1 2 RXD1 3 TXD1 4 DTR1 COM1 5 GND 6 DSR1 COM1 7 RTS1 8 CTS1 9 RI1 10 VCC 11 DCD2 12 RX2 13 TXD2 14 DTR2 COM2 15 GND 16 DSR2 COM2 17 RTS2 18 CTS2 19 RI2 20 VCC 21 PD0 22 SLCT 23 PD1 24 PR 25 PD2 26 BUSY PRN 27 PD3 28 ACK\ PRN. 29 PD4 30 SLCTIN\ 31 PD5 32 INIT\ 33 PD6 34 ERROR\ 35 PD7 36 AUTOFD\ 37 GND 38 STORBE\ 39 GP0 40 GP8 41 GP1 42 GP9 43 GP2 44 GP10 45 GP3 46 GP11 GPIO 47 GP4 48 GP12 GPIO 49 GP5 50 GP13 51 GP6 52 GP14 (DOC) 53 GP7 54 GP15 GPCS 55 GPCS0 56 VBAT BAT+ KBD. 57 KBDAT 58 HDCS0 IDE. 59 KBCLK 60 HDCS1 SPK. 61 SPKR 62 RESETL RESET 63 GND 64 PWG Mity Soc CPU Module : Mity SoC Module 2MB//2MB/2S/IDE/Parallel/GPIO 17
24 U2: DRAM 2MB (Option) 1 1 VCC 42 GND 2 DO 41 D15 3 D1 40 D14 4 D2 39 D13 5 D3 38 D12 6 VCC 37 GND 7 D4 36 D11 8 D5 35 D10 9 D6 34 D9 10 D7 33 D8 11 NC 32 NC 12 NC 31 CASL 13 WE 30 CASH 14 RAS 29 OE 15 A11 28 A9 16 A10 27 A8 17 A0 26 A7 18 A1 25 A6 19 A2 24 A5 20 A3 23 A4 21 VCC 22 GND U3: DRAM 2MB (Standard) 1 1 VCC 42 GND 2 DO 41 D15 3 D1 40 D14 4 D2 39 D13 5 D3 38 D12 6 VCC 37 GND 7 D4 36 D11 8 D5 35 D10 9 D6 34 D9 10 D7 33 D8 11 NC 32 NC 12 NC 31 CASL 13 WE 30 CASH 14 RAS 29 OE 15 A11 28 A9 16 A10 27 A8 17 A0 26 A7 18 A1 25 A6 19 A2 24 A5 20 A3 23 A4 21 VCC 22 GND 18 Mity Soc CPU Module : Mity SoC Module 2MB/2S/IDE/Parallel/GPIO
25 U8: BIOS 32-pin PLCC Socket 1 MA18 2 SA16 3 SA15 4 SA12 5 SA7 6 SA6 7 SA5 8 SA4 9 SA3 10 SA2 11 SA1 12 SA0 13 XD0 14 XD1 15 XD2 16 GND 17 XD3 18 XD4 19 XD5 20 XD6 21 XD7 22 KBSJ 23 SA10 24 MEMR 25 SA11 26 SA9 27 SA8 28 SA13 29 SA14 30 MA17 31 SMEMW 32 VCC Mity Soc CPU Module : Mity SoC Module 2MB//2MB/2S/IDE/Parallel/GPIO 19
26 Mity SoC Development Board J1: X-ISA Connector x2-Box Header 1 GND 2 SBHE 3 RSTDRV 4 SD7 5 VCC 6 SD6 7 SD8 8 SD5 9 SD9 10 SD4 11 SD10 12 SD3 13 SD11 14 SD2 15 SD12 16 SD1 17 SD13 18 SD0 19 GND 20 IOCHRDY 21 SMEMW 22 AEN 23 SMEMR 24 SA19 25 XIOW 26 SA18 27 XIOR 28 SA17 29 SD14 30 SA16 31 SD15 32 SA15 33 MEMCS16 34 SA14 35 TOCS16 36 SA13 37 REFRESH 38 SA12 39 SYSCLK 40 SA11 41 IRQ7 42 SA10 43 IRQ6 44 SA9 45 IRQ5 46 SA8 47 IRQ4 48 SA7 49 IRQ3 50 SA6 51 IRQ10 52 SA5 53 IRQ11 54 SA4 55 BALE 56 SA3 57 VCC 58 SA2 59 XOSC 60 SA1 61 GND 62 SA0 63 IRQ12 64 IRQ14 20 Mity Soc CPU Module : Mity SoC Module 2MB/2S/IDE/Parallel/GPIO
27 J2 : ISA Bus SL62 62-pin Gold finger (Total 98 pins) J3 : 36-pin J2 : 62-pin 1 (A1) IOCHCK 2 (B1) GND 3 SD7 4 RSTDRV 5 SD6 6 VCC 7 SD5 8 IRQ9 9 SD4 10-5V 11 SD3 12 DRQ2 13 SD V 15 SD1 16 OWS 17 SD V 19 IOCHRDY 20 GND 21 AEN 22 SMEMW 23 SA19 24 SMEMR 25 SA18 26 IOW 27 SA17 28 IOR 29 SA16 30 DACK3 31 SA15 32 DRQ3 33 SA14 34 DACK1 35 SA13 36 DRQ1 37 SA12 38 REFRESH 39 SA11 40 SYSCLK 41 SA10 42 IRQ7 43 SA9 44 IRQ6 45 SA8 46 IRQ5 47 SA7 48 IRQ4 49 SA6 50 IRQ3 51 SA5 52 DACK2 53 SA4 54 TC 55 SA3 56 BALE 57 SA2 58 VCC 59 SA1 60 OSC 61 SA0 62 GND Mity Soc CPU Module : Mity SoC Module 2MB//2MB/2S/IDE/Parallel/GPIO 21
28 J3 : ISA bus SL36 36-pin Gold finger (Total 98 pins) J3 : 36-pin J2 : 62-pin 1 (A1) SBHE 2 (B1) MEMCS16 3 LA23 4 IOCS16 5 LA22 6 IRQ10 7 LA21 8 IRQ11 9 LA20 10 IRQ12 11 LA19 12 IRQ15 13 LA18 14 IRQ14 15 LA17 16 DACK0 17 MEMR 18 DRQ0 19 MEMW 20 DACK5 21 SD8 22 DRQ5 23 SD9 24 DACK6 25 SD10 26 DRQ6 27 SD11 28 DACK7 29 SD12 30 DRQ7 31 SD13 32 VCC 33 SD14 34 MASTER 35 SD15 36 GND 22 Mity Soc CPU Module : Mity SoC Module 2MB/2S/IDE/Parallel/GPIO
29 J4: PC/104 Connector - 64-pin Header Connector (CN1) 1 IOCHCHK * 2 GND 3 SD7 4 RSTDRV 5 SD6 6 VCC 7 SD5 8 IRQ9 9 SD4 10-5V 11 SD3 12 DRQ2 13 SD V 15 SD1 16 OWS* 17 SD V 19 IOCHRDY 20 GND 21 AEN 22 SMEMW * 23 SA19 24 SMEMR * 25 SA18 26 XIOW * 27 SA17 28 XIOR * 29 SA16 30 DACK3 * 31 SA15 32 DRQ3 33 SA14 34 DACK1 * 35 SA13 36 DRQ1 37 SA12 38 REFRESH * 39 SA11 40 SYSCLK 41 SA10 42 IRQ7 43 SA9 44 IRQ6 45 SA8 46 IRQ5 47 SA7 48 IRQ4 49 SA6 50 IRQ3 51 SA5 52 DACK2 * 53 SA4 54 TC 55 SA3 56 BALE 57 SA2 58 VCC 59 SA1 60 XXOSC 61 SA0 62 GND 63 GND 64 GND Mity Soc CPU Module : Mity SoC Module 2MB//2MB/2S/IDE/Parallel/GPIO 23
30 J4 PC/104 Connector 40-pin Header Connector (CN2) 1 GND 2 GND 3 MEMCS16 * 4 SBHE * 5 IOCS16 * 6 LA23 7 IRQ10 8 LA22 9 IRQ11 10 LA21 11 IRQ12 12 LA20 13 IRQ15 14 LA19 15 IRQ14 16 LA18 17 DACK0 * 18 LA17 19 DRQ0 20 MEMR * 21 DACK5 * 22 MEMW * 23 DRQ5 24 SD8 25 DACK6 * 26 SD9 27 DRQ6 28 SD10 29 DACK7 * 30 SD11 31 DRQ7 32 SD12 33 VCC 34 SD13 35 MASTER * 36 SD14 37 GND 38 SD15 39 GND 40 NC 24 Mity Soc CPU Module : Mity SoC Module 2MB/2S/IDE/Parallel/GPIO
31 J6: Mity-Mite VGA Connector x2-Box Header 1 GND 2 SBHE 3 RSTDRV 4 SD7 5 VCC 6 SD6 7 SD8 8 SD5 9 SD9 10 SD4 11 SD10 12 SD3 13 SD11 14 SD2 15 SD12 16 SD1 17 SD13 18 SD0 19 GND 20 IOCHRDY 21 SMEMW 22 AEN 23 SMEMR 24 SA19 25 XIOW 26 SA18 27 XIOR 28 SA17 29 SD14 30 SA16 31 SD15 32 SA15 33 MEMCS16 34 SA14 35 TOCS16 36 SA13 37 REFRESH 38 SA12 39 SYSCLK 40 SA11 41 IRQ7 42 SA10 43 IRQ6 44 SA9 45 IRQ5 46 SA8 47 IRQ4 48 SA7 49 IRQ3 50 SA6 51 IRQ10 52 SA5 53 IRQ11 54 SA4 55 BALE 56 SA3 57 VCC 58 SA2 59 XOSC 60 SA1 61 GND 62 SA0 63 IRQ12 64 IRQ14 Mity Soc CPU Module : Mity SoC Module 2MB//2MB/2S/IDE/Parallel/GPIO 25
32 J7: IDE Connector pitch 40-pin Box Header 1 RESETL 2 GND 3 SD7 4 SD8 5 SD6 6 SD9 7 SD5 8 SD10 9 SD4 10 SD11 11 SD3 12 SD12 13 SD2 14 SD13 15 SD1 16 SD14 17 SD0 18 SD15 19 GND 20 VCC 21 NC 22 GND 23 XXIOW 24 GND 25 XXIOR 26 GND 27 NC 28 NC 29 NC 30 GND 31 IRQ14 32 IOCS16 33 SA1 34 NC 35 SA0 36 SA2 37 HDCS0 38 HDCS-1 39 IDELED 40 GND 26 Mity Soc CPU Module : Mity SoC Module 2MB/2S/IDE/Parallel/GPIO
33 J8: I/O Connector x2-Box Header 1 DCD1 2 RXD1 3 TXD1 4 DTR1 COM1 5 GND 6 DSR1 COM1 7 RTS1 8 CTS1 9 RI1 10 VCC 11 DCD2 12 RX2 13 TXD2 14 DTR2 COM2 15 GND 16 DSR2 COM2 17 RTS2 18 CTS2 19 RI2 20 VCC 21 PD0 22 SLCT 23 PD1 24 PR 25 PD2 26 BUSY PRN 27 PD3 28 ACK\ PRN. 29 PD4 30 SLCTIN\ 31 PD5 32 INIT\ 33 PD6 34 ERROR\ 35 PD7 36 AUTOFD\ 37 GND 38 STORBE\ 39 GP0 40 GP8 41 GP1 42 GP9 43 GP2 44 GP10 45 GP3 46 GP11 GPIO 47 GP4 48 GP12 GPIO 49 GP5 50 GP13 51 GP6 52 GP14 (DOC) 53 GP7 54 GP15 GPCS 55 GPCS0 56 VBAT BAT+ KBD. 57 KBDAT 58 HDCS0 IDE. 59 KBCLK 60 HDCS1 SPK. 61 SPKR 62 RESETL RESET 63 GND 64 PWG Mity Soc CPU Module : Mity SoC Module 2MB//2MB/2S/IDE/Parallel/GPIO 27
34 J9: GPIO - 20-pin Box Header 1 GND 2 VCC 3 GP0 4 GP8 5 GP1 6 GP9 7 GP2 8 GP10 9 GP3 10 GP11 11 GP4 12 GP12 13 GP5 14 GP13 15 GP6 16 GP14 17 GP7 18 GP15 19 VCC 20 GND J10 : COM1 9-pin D-Sub Connector J11 : COM2-10-pin Box Header J12: RESET - 2-pin Header 1 PWG 2 GND 1 DCD1 2 RXD1 3 TXD1 4 DTR1 5 GND 6 DSR1 7 RTS1 8 CTS1 9 RI DCD2 2 RXD2 3 TXD2 4 DTR2 5 GND 6 DSR2 7 RTS2 8 CTS2 9 RI2 10 VCC 28 Mity Soc CPU Module : Mity SoC Module 2MB/2S/IDE/Parallel/GPIO
35 J13 : PS/2 Keyboard - 5-pin Molex Header 1 KBCLK 2 KBDAT 3 NC 4 GND 5 VCC J14: VGA Connector - 15-pin D-Sub Connector (female) 1 R 6 GND 11 NC 2 G 7 GND 12 NC 3 B 8 GND 13 HYSYNC 4 NC 9 NC 14 VSYNC 5 GND 10 GND 15 NC J15: DC_INPUT - 2-pin Terminal Block 1 VCC 2 GND J16: DC_JACK - 3-pin Jack 1 VCC 2 GND 3 NC Mity Soc CPU Module : Mity SoC Module 2MB//2MB/2S/IDE/Parallel/GPIO 29
36 J17: DC_INPUT - 4-pin Molex Header 1 VCC 2 GND 3 GND 4 +12V J18 : Mity-Mite VGA pin Box Header 1 R 2 GND 3 G 4 GND 5 B 6 GND 7 HSYNC 8 GND 9 VSYNC 10 GND J19 : PS/2 Keyboard & Mouse - 6-pin Mini-Din Connector 1 KBCLK 2 NC 3 GND 4 KBDAT 5 NC 6 VCC 7 GND 8 GND 9 GND 30 Mity Soc CPU Module : Mity SoC Module 2MB/2S/IDE/Parallel/GPIO
37 J20 : PRINT - 26-pin Box Header 1 STORBE 2 PD0 3 PD1 4 PD2 5 PD3 6 PD4 7 PD5 8 PD6 9 PD7 10 ACK\ 11 BUSY 12 PE 13 SLCT 14 AUTOFD 15 ERROR\ 16 INIT\ 17 SLCTIN\ 18 GND 19 GND 20 GND 21 GND 22 GND 23 GND 24 GND 25 GND 26 NC LED DISPLAY: Green LED x16 D2 XGP0 D3 XGP1 D4 XGP2 D5 XGP3 D6 XGP4 D7 XGP5 D8 XGP6 D9 XGP7 D10 XGP8 D11 XGP9 D12 XGP10 D13 XGP11 D14 XGP12 D15 XGP13 D16 XGP14 D17 XGP15 Mity Soc CPU Module : Mity SoC Module 2MB//2MB/2S/IDE/Parallel/GPIO 31
38 U2 : DOC (DiskOnChip) : 32-pin Grid hole DIP Socket 1 NC 2 NC 3 SA15 4 SA12 5 SA7 6 SA6 7 SA5 8 SA4 9 SA3 10 SA2 11 SA1 12 SA0 13 SD0 14 SD1 15 SD2 16 GND 17 SD3 18 SD4 19 SD5 20 SD6 21 SD7 22 GPSC0 23 SA10 24 SMEMR 25 SA11 26 SA9 27 SA8 28 SA13 29 SA14 30 NC 31 SMEMW 32 VCC U5 : 8 PORT 18-pin 7-Segment DIP SSD 1 H_SEGE 2 H_SEGD 3 H_SEGC 4 NC 5 L_SEGE 6 L_SEGD 7 L-SEGG 8 L_SEGC 9 NC 10 L_SEGB 11 L_SEGA 12 L_SEGF 13 VCC 14 VCC 15 H_SEGB 16 H_SEGA 17 H_SEGG 18 H_SEGF 32 Mity Soc CPU Module : Mity SoC Module 2MB/2S/IDE/Parallel/GPIO
39 2.5 DiskOnChip Flash Disk Setup a DiskOnChip 2000 Flash Disk Installation Instructions 1. Make sure the power of Mity SoC Module is turned OFF. 2. Plug the DiskOnChip 2000 device into its socket. Verify the mounting orientation of the DiskOnChip 2000 is correct (DiskOnChip 2000 pin 1 must be aligned with pin 1 of the socket). 3. Set the address for both DiskOnChip and Flash Disk devices following the instructions below: Step1: Enter to AMI BIOS Setup Utility while system power on. Step2: Enter to Advanced Chipset Setup. Step3: Select GPCS Function to Enable. (For DiskOnChip) Step4: Select GPCS0 Command to MEMR/W 8bit. Step5: Select GPCS0 Start Address to 0C8000 HEX. Step6: Select GPCS0 Size to 8 KBYTE (go to Step 10). (For Flash Disk) Step4: Setect GPCS0 Command to MEMR/W 8bit. Step5: Select GPCS0 Start Address to 0E0000 HEX. Step6: Select GPCS0 Size to 64 KBYTE. Step7: Select GPCS1 Command to IOW 8bit. Step8: Select GPCS1 Start Address to HEX. Step9: Select GPCS1 Size to 2 BYTE. Step10: Save changes and exit. 4. Power up the system. 5. During power up, you may observe the messages displayed by the DiskOnChip 2000 when its drivers are automatically loaded into system s memory. 6. At this stage, the DiskOnChip 2000 can be access as any disk in the system. 7. If the DiskOnChip 2000 is the only disk in the system, it will appear as the first disk (drive C: in DOS). 8. If there are more disks besides the DiskOnChip 2000, the DiskOnChip 2000 will appear by default as the last drive, unless it was programmed as first drive. (please refer to the DiskOnChip 2000 utilities user manual). 9. If you want the DiskOnChip 2000 to be bootable: a - copy the operating system files into the DiskOnChip by using the standard DOS command (for example: sys d:) b - The Mity Soc CPU Module : Mity SoC Module 2MB//2MB/2S/IDE/Parallel/GPIO 33
40 DiskOnChip should be the only disk in the systems or should be configured as the first disk in the system (c: ) using the DUPDATE utility For more information on DiskOnChip2000 technology, visit M-Systems Web site where you can find Utilities Manual, Data Sheets and Application Notes. In addition, you can find the lasted DiskOnChip 2000 S/W Utilities. 34 Mity Soc CPU Module : Mity SoC Module 2MB/2S/IDE/Parallel/GPIO
41 2.6 Watchdog Timer The watchdog timer uses a KHz frequency source with a 24-bit counter. Its time range stretches from 30.5 ms to 512 sec. with a resolution of 30.5 ms. When the watchdog times out, a System RESET, NMI or IRQ can be invoked. Watchdog timer control and the 24-bit counter itself occupy 6 consecutive 8-bit address locations. When functioning properly, the system resets the watchdog timer periodically to prohibit that it times out. If the watchdog timer times out, it will RESET the system, or generate and NMI or IRQ, depending on its configuration. Watchdog or System Timer Another great application is to generate a periodic IRQ signal. Under DOS environment, the 8254, system timer 0, will generate IRQ0 every 54.9 ms. The watchdog is like a system timer 0. It can be programmed to periodically generate a configurable IRQ. It may be clear that the selected IRQ, will no longer be available to the system. Configuring the Watchdog Timer in the BIOS The Vortex86 watchdog configuration register can be controlled by software or can be setup in the BIOS. To do so, go to BIOS Setup s Advanced Chipset Setup Watchdog Function = Enable/Disable Watchdog = RESET, NMI or IRQ 3/4/5/6/7/9/10/11/12/14/15 Watchdog Timer = 1/2/4/8/16/32/64/128/256/512 Seconds The BIOS setup only offers a limited amount of time-out values. To obtain a more higher resolution of timeout values, refer to the next paragraph Configuring the Watchdog Timer by Software. Note that in case of using the BIOS setup, the watchdog starts counting the moment it passes the BIOS setup. This means that if you set the time-out period to 1 second, the system will keep rebooting before being able to load operating system or software! After you have finished configuring your watchdog timer, it reads Timeout Status & Reset - INDEX 3CH on page 23; and look at the example on page 24 to find out how to periodically resetting the timeout status to prevent the watchdog timer from invoking a RESET, NMI or IRQ. Mity Soc CPU Module : Mity SoC Module 2MB//2MB/2S/IDE/Parallel/GPIO 35
42 Configuring the Watchdog Timer by Software Chipset configuration registers The Vortex86 configuration register INDEX 37H, 38H, 39H, 3AH, 3BH, 3Ch are used to control the watchdog functions and/or display its current status. Enable/Disable watchdog - INDEX 37H Bit Value Action 7 reserved Do not modify the value of these bits! Disable watchdog timer Enable watchdog timer 5-0 Other function Do not modify the value of these bits! Watchdog time out action - INDEX 38H Bit Value Action No output signal 0001 IRQ IRQ IRQ IRQ IRQ IRQ IRQ IRQ IRQ IRQ IRQ NMI 1101 System RESET 1110 No output signal 1111 No output signal 3-0 Other function Do not modify the value of these bits! Watchdog timer - INDEX 39H, 3AH, 3BH Index 3Bh 3Ah 39h Bits D7 D0 D7 D0 D7 D0 counter [VSB......LSB] 36 Mity Soc CPU Module : Mity SoC Module 2MB/2S/IDE/Parallel/GPIO
43 For example Index 3Bh 3Ah 39h Time out 00h 00h 01h 30.5µs 00h 00h 02h 61µs 00h 01h 00h 7.8 ms 00h 02h 00h 15.6 ms 01h 00h 00h 2 s 02h 00h 00h 4 s FFh FFh FFh 512 s Timeout Status & Reset - INDEX 3CH Bit Value Action Timeout has not occurred Timeout has occured Reset timer Has no meaning 5-0 Other function, do not modify these bits Programming the watchdog To perform any operation on the Vortex86 configuration registers you always have to unlock first and lock the registers afterwards. Unlock configuration register mov al, 013h out 22h, al nop nop nop nop mov al, 0c5h out 23h, al nop nop nop nop Lock configuration register mov al, 013h out 22h, al mov al, 000h out 23h, al Mity Soc CPU Module : Mity SoC Module 2MB//2MB/2S/IDE/Parallel/GPIO 37
44 Read the value of a configuration register For example, read INDEX 3Ch : Unlock configuration register mov al, 03ch out 22h, al nop nop in al, 23h nop nop push ax Lock configuration register pop ax ;AL - result Write data to configuration register For example, write 0FFh to INDEX 3Bh : Unlock configuration register mov al, 03bh out 22h, al nop nop mov al, 0ffh out 23h, al nop nop Lock configuration register Watchdog Program Example We use the following sequence to initialize the watchdog timer: (1) Unlock configuration register. (2) Disable watchdog timer by setting INDEX 37H Bit 6 to 0. (3) Set the expected counter value to INDEX 3BH, 3AH, 39H. (4) Select timeout action from INDEX 38H Bit 7-4. (5) Enable watchdog timer by setting INDEX 37H Bit 6 to Mity Soc CPU Module : Mity SoC Module 2MB/2S/IDE/Parallel/GPIO
45 (6) Lock configuration register. Example: Set timeout to 128 sec to generate a system RESET. ; Please use MASM to compiler the following program ; Execute under DOS environment dosseg. model small. stack 100h.code main proc mov ax, 0c513h ; Unlock config. register call writechip mov ax, 03737h ; Disable watchdog timer call readchip and al, b xchg ah, al call writechip mov ax, 0403bh ; Set the expected counter ; value call writechip ; to [400000h] mov ax, 0003ah ; 30.5*sec*400000h= 128 sec call writechip mov ax, 00039h call writechip mov ax, 03838h ; Select system reset as ; timeout action call readchip and al, b or al, b xchg ah, al call writechip mov ax, 03737h ; Enable watchdog timer call readchip or al, b xchg ah, al call writechip mov ax, 00013h ; Lock config. register call writechip mov ax, 04c00h int 21h main endp Mity Soc CPU Module : Mity SoC Module 2MB//2MB/2S/IDE/Parallel/GPIO 39
46 readchip proc out 22h, al nop nop in al, 23h nop nop ret readchip endp writechip proc out 22h, al nop nop xchg ah, al out 23h, al nop nop xchg ah, al ret writechip endp end main Reset watchdog timer Resets the watchdog timer periodically to prevent timeout. mov ax, 0c513h ; Unlock configuration ; register call writechip mov ax, 03C3Ch ; Reset watchdog timer ; counter call readchip or al, ; The counter is reset at xchg ah, al ; out 23h, al call writechip mov ax, 00013h ; Lock configuration ; register call writechip (the above code uses readchip and writechip procedures) 40 Mity Soc CPU Module : Mity SoC Module 2MB/2S/IDE/Parallel/GPIO
47 2.6 General Purpose I/O M6117D supports 16 independent GPOs and GPIs. This group of GPOs does not need external 74LS373 to latch as generate purpose output. Also this group of GPIs do not share signals with the ISA data bus, so no external 74LS245 is required either. At boot time the state of the GPIO ports can be set in the BIOS. Go to BIOS Setup s Advanched Chipset Setup GPIO Sample Program ; Please use TASM to compiler the following program. ; Execute under DOS environment. ;.286.model small.code mov al,13h ; Unlock M6117D configuration register. out 22h,al ; mov al,0c5h ; out 23h,al ; mov al,4eh ; Enable GPIO[7-0] is output pin. out 22h,al ; mov al,0ffh ; If AL fill FF, then ; GPIO[7-0] set as output pin. out 23h,al ; User can be set logic 1 ; of OUT direction. mov al,4fh ; Enable GPIO[15-8] is input pin out 22h,al ; mov al,00 ; If AL fill 00, then ; GPIO[15-8] set as input pin. out 23h,al ; User can be set logic 0 ; of IN direction. mov al,47h ; Output data port. out 22h,al ; mov al,55h ; Example data out value is 55, ; to output pin out 23h,al ; GPIO[7-0]. So user can ; repeat this loop. mov al,46h ; If GPIO[7-0] is set input direction, then data out 22h,al ; input port is 46. in al,23h ; Example data input value Mity Soc CPU Module : Mity SoC Module 2MB//2MB/2S/IDE/Parallel/GPIO 41
48 mov al,4ch out 22h,al ; in al,23h ; from data input GPIO[7-0] ; Input data port ; Read data from GPIO[15-8] ; into AL register. mov al,4dh ; If GPIO[15-8] is set output ; direction, then data out 22h,al ; output port is 4d. mov al,55h ; output data value is 55. out 23h,al... continue program end ; Example data output value ; to data input GPIO[15-8] 42 Mity Soc CPU Module : Mity SoC Module 2MB/2S/IDE/Parallel/GPIO
49 C h a p t e r 3 SVGA Setup 3.1 Introduction The ICOP-6054VE has an on-board VGA interface. The specifications and features are described as follows: Chipset The ICOP-6054VE uses a HMC HM86508 for its SVGA controller, which supports conventional analog CRT monitor or flat panel. In addition, it also supports interlaced and non-interlaced analog monitors (color and monochrome VGA) in high-resolution modes while maintaining complete IBM VGA compatibility. Multiple frequency (multisync) monitors are handled as if they were analog monitors Display memory With 1 MB memory, the VGA controller can drive CRT displays or color panel displays with resolutions up to 1024 x 768 at 256 colors. Mity Soc CPU Module : Mity SoC Module 2MB//2MB/2S/IDE/Parallel/GPIO 43
50 3.1.3 VGA/Flat Panel Connectors Flat Panel Connector Pin Assignment (44 Pin for all ICOP 386 Series) Pin Description Pin Description 1 +12V 2 +12V 3 GND 4 GND 5 PVcc 6 PVcc 7 ENAVEE 8 ENAVEE 9 P0 10 P1 11 P2 12 P3 13 P4 14 P5 15 P6 16 P7 17 P8 18 P9 19 P10 20 P11 21 P12 22 P13 23 P14 24 P15 25 P16 26 P17 27 P18 28 P19 29 P20 30 P21 31 P22 32 P23 33 GND 34 GND 35 SHFCLK 36 FLM 37 M 38 LP 39 GND 40 ENABKL 41 GND 42 ASHFCLK 43 Vcc 44 Vcc 44 Mity Soc CPU Module : Mity SoC Module 2MB/2S/IDE/Parallel/GPIO
51 Description for the Pin of the Flat Panel Connector Description P0~P23 Flat panel data output ENABKL Activity Indicator and Enable Backlight outputs SHFCLK Shift clock. Pixel clock for flat panel data M M signal for panel AC drive control LP Latch pulse. Flat panel equivalent of HSYNC FLM First line marker. Flat panel equivalent of VSYNC +12V +12V power from PC power supply ENAVDD Power sequencing controls for panel LCD bias volt ENAVEE Power sequencing controls for panel LCD bias volt SHFCLK The inverter signal of SHFCLK VDDM 3.3V or 5V selected by JP6 3.2 Flat Panel BIOS and Wiring Below is a list of optional Flat Panel SVGA BIOS. The VGA BIOS is combined with the system BIOS in a single. To change to another BIOS please contact your local dealer. MLCD.dat - Data File for MONO DSTN640*480 (Default) example : (1) HOSIDEN HLM6667 (2) HITACHI LMG5160XUFC (3) CASIO MD650TS00-01 (4) OPTREX DMF_50260NFU-FW-8 DSTN.dat - Data file for Color DSTN640*480 example : (1) Sanyo LCM NTK (2) SHARP LM64C35P TFT_S1.dat - Data File for TFT640*480-Sync (16 BIT) TFT_S2.dat - Data File for TFT640*480-Sync (18/24 BIT) example : (1) HITACHI TX26D60/TX24D55 (2) TOSHIBA LTM09C015A (3) SHARP LQ10D321 TFT_LP1.dat - Data File For TFT640*480-LP (16 BIT) TFT_LP2.dat - Data File For TFT640*480-LP (18/24 BIT) Mity Soc CPU Module : Mity SoC Module 2MB//2MB/2S/IDE/Parallel/GPIO 45
52 example : (1) Toshiba LTM09c015A) TFT86_S1.dat - Data File for TFT800*600_sync (16 BIT) TFT86_S2.dat Data File for TFT800*600_sync (18/24 BIT) example : (1) NEC NL8060AC26-05 (2) NEC NL8060AC26-04 (3) NEC NL8060BC31-02 EL.dat - Data File for EL640*480 example : (1) PLANAR EL A PLASMA.dat - Data File for PLASMA640*480 example : (1) PANASONIC S817 CRT/Flat Panel Mode All the above BIOS support either CRT only, Flat Panel only or CRT/Flat Panel simultaneously. To set the mode a Panel Switching Utility is used. USAGE: At DOS prompt type >SW508 then Screen will show 1. CRT Only 2. Panel Only 3. CRT/Panel Simutaneous 46 Mity Soc CPU Module : Mity SoC Module 2MB/2S/IDE/Parallel/GPIO
53 NEC NL6448AC33-18 wiring NEC NL6448AC33-18 ICOP-6054VE CON1 Pin Pin Pin Pin CN1-1 GND 3 GND CN1-2 CLK 35 SHFCLK CN1-3 Hsync 38 LP CN1-4 Vsync 36 FLM CN1-5 GND 4 - CN1-6 R0 27 P18 CN1-7 R1 28 P19 CN1-8 R2 29 P20 CN1-9 R3 30 P21 CN1-10 R4 31 P22 CN1-11 R5 32 P23 CN1-12 GND 33 - CN1-13 G0 19 P10 CN1-14 G1 20 P11 CN1-15 G2 21 P12 CN1-16 G3 22 P13 CN1-17 G4 23 P14 CN1-18 G5 24 P15 CN1-19 GND 34 - CN1-20 B0 11 P2 CN1-21 B1 12 P3 CN1-22 B2 13 P4 CN1-23 B3 14 P5 CN1-24 B4 15 P6 CN1-25 B5 16 P7 CN1-26 GND 39 - CN1-27 ENAB 37 MDE CN1-28 Vcc 43 Vcc CN1-29 Vcc 44 Vcc CN1-30 NC - - CN1-31 NC - - Mity Soc CPU Module : Mity SoC Module 2MB//2MB/2S/IDE/Parallel/GPIO 47
54 NEC NL6448AC30-10 wiring NEC NL6448AC30-10 ICOP-6054VE CON1 Pin Pin Pin Pin CN1-1 CLK 42 SHFCLK CN1-2 Hsync 38 LP CN1-3 Vsync 36 FLM CN1-4 DE 37 MDE CN P0 CN1-6 B0 10 P1 CN1-7 B1 11 P2 CN1-8 B2 12 P3 CN1-9 B3 13 P4 CN P5 CN P6 CN1-12 G0 16 P7 CN1-13 G1 17 P8 CN1-14 G2 18 P9 CN1-15 G3 19 P10 CN P11 CN1-17 R0 21 P12 CN1-18 R1 22 P13 CN1-19 R2 23 P14 CN1-20 R3 24 P15 CN P16 CN P17 CN P18 CN P19 CN P20 CN P21 CN P22 CN P23 CN1-29 PVcc 5 LCD Vdd CN1-30 Vcc 43 Vcc CN1-31 MODE 44 Vcc CN1-32 GND 3 GND CN1-33 GND 4 GND CN1-34 Vdd CN1-35 ENABKL 40 ENABKL CN1-36 GND 39 GND 48 Mity Soc CPU Module : Mity SoC Module 2MB/2S/IDE/Parallel/GPIO
55 LJ32H028 wiring LJ32H028 ICOP-6054VE CON1 Pin Pin Pin Pin CN1-1 D1 11 P2 CN1-2 D0 12 P3 CN1-3 D3 9 P0 CN1-4 D2 10 P1 CN1-5 CP2 35 SHF_CLK CN1-6 GND 3,4 GND CN1-7 CP1 38 LP CN1-8 GND 33,34 GND CN1-9 S 36 FLM CN CN CN CN V 43,44 +5V(Vdd) CN CN V 1,2 +12V Mity Soc CPU Module : Mity SoC Module 2MB//2MB/2S/IDE/Parallel/GPIO 49
56 SHARP LQ10D42 wiring (640 X 480 TFT Color) SHARP LQ10D42 ICOP-6054VE CON1 Pin Pin Pin Pin CN1-1 GND 3,4 GND CN1-2 CLK 42 SHFCLK CN1-3 Hsync 38 LP CN1-4 Vsync 36 FLM CN1-5 GND 3,4 GND CN1-6 R0 21 P12 CN1-7 R1 22 P13 CN1-8 R2 23 P14 CN1-9 R3 24 P15 CN1-10 R4 25 P16 CN1-11 R5 26 P17 CN1-12 GND 3,4 GND CN1-13 G0 15 P6 CN1-14 G1 16 P7 CN1-15 G2 17 P8 CN1-16 G3 18 P9 CN1-17 G4 19 P10 CN1-18 G5 20 P11 CN1-19 GND 3,4 GND CN1-20 B0 9 P0 CN1-21 B1 10 P1 CN1-22 B2 11 P2 CN1-23 B3 12 P3 CN1-24 B4 13 P4 CN1-25 B5 14 P5 CN1-26 GND 3,4 GND CN1-27 ENAB 40 M CN1-28 Vcc 43,44 Vcc +5V CN1-29 Vcc 43,44 Vcc +5V CN1-30 R/L - - CN1-31 U/D Mity Soc CPU Module : Mity SoC Module 2MB/2S/IDE/Parallel/GPIO
57 SHARP LQ12S31 wiring (800 X 600 TFT Color) SHARP LQ12S31 ICOP-6054VE CON1 Pin Pin Pin Pin CN1-1 GND 3 GND CN1-2 CLK 35 SHFCLK CN1-3 GND 4 GND CN1-4 Hsync 38 LP CN1-5 Vsync 36 FLM CN1-6 GND 8 GND CN1-7 GND 8 GND CN1-8 GND 8 GND CN1-9 R0 27 P18 CN1-10 R1 28 P19 CN1-11 R2 29 P20 CN1-12 GND 8 GND CN1-13 R3 30 P21 CN1-14 R4 31 P22 CN1-15 R5 32 P23 CN1-16 GND 39 GND CN1-17 GND 39 GND CN1-18 GND 39 GND CN1-19 G0 19 P10 CN1-20 G1 20 P11 CN1-21 G2 21 P12 CN1-22 GND 39 CN1-23 G3 22 P13 CN1-24 G4 23 P14 CN1-25 G5 24 P15 CN1-26 GND 41 GND CN1-27 GND 41 GND CN1-28 GND 41 GND CN1-29 B0 11 P2 CN1-30 B1 12 P3 CN1-31 B2 13 P4 CN1-32 GND 41 GND CN1-33 B3 14 P5 CN1-34 B4 15 P6 CN1-35 B5 16 P7 CN1-36 GND 41 GND CN1-37 ENAR 37 M CN1-38 TST - - CN1-39 Vcc 43 +5Vcc CN1-40 Vcc 44 +5Vcc CN1-41 TST - - Mity Soc CPU Module : Mity SoC Module 2MB//2MB/2S/IDE/Parallel/GPIO 51
58 C h a p t e r 4 Network Interface 4.1 Introduction The Realtek RTL-8019AS 10Mbps Ethernet controller board supports both 10BASE-T and Coax 10Base-2 BNC connectors, and allows direct connec-tion to your 10Mbps Ethernet based Local Area Network for full interaction with local servers, wide area networks such as the Internet. I/O and IRQ settings can be done by software with the supplied utility software, or it can be set for Plug and Play compatibility. The controller supports : Full-Duplex Ethernet function to double channel bandwidth, auto media detection. 4.2 Software Support On-board EEPROM (93C46) programming Setup/Diagnostic program for DOS Help utility for easy installation RPL boot ROM for Novell Netware, Microsoft NT NDIS2 (DOS,OS/2,Lantastic,WFW3.1 K K) NDIS3,NDIS4,NDIS5 for WIN95,98,NT3.51,4.0,5.0,WFW3.11 Netware 16-bit ODI driver for DOS,OS/2 and 32-bit ODI driver for Netware 3.x,4.x,5.0 Server Packet driver for UNIX Client SCO Unix driver Linux driver All operating systems that support standard NE Mity Soc CPU Module : Mity SoC Module 2MB/2S/IDE/Parallel/GPIO
59 A p p e n d i x Schematic Diagram - Please refer to the schematic diagram on the preceding 3 pages. - Mity Soc CPU Module : Mity SoC Module 2MB//2MB/2S/IDE/Parallel/GPIO 53
60 54 Mity Soc CPU Module : Mity SoC Module 2MB/2S/IDE/Parallel/GPIO
61 Mity Soc CPU Module : Mity SoC Module 2MB//2MB/2S/IDE/Parallel/GPIO 55
62 56 Mity Soc CPU Module : Mity SoC Module 2MB/2S/IDE/Parallel/GPIO
63 Warranty This product is warranted to be in good working order for a period of one year from the date of purchase. Should this product fail to be in good working order at any time during this period, we will, at our option, replace or repair it at no additional charge except as set forth in the following terms. This warranty does not apply to products damaged by misuse, modifications, accident or disaster. Vendor assumes no liability for any damages, lost profits, lost savings or any other incidental or consequential damage resulting from the use, misuse of, originality to use this product. Vendor will not be liable for any claim made by any other related party. Return authorization must be obtained from the vendor before returned merchandise will be accepted. Authorization can be obtained by calling or faxing the vendor and requesting a Return Merchandise Authorization (RMA) number. Returned goods should always be accompanied by a clear problem description. Mity Soc CPU Module : Mity SoC Module 2MB//2MB/2S/IDE/Parallel/GPIO 57
ICOP-6050F Embedded 386SX PC/104 CPU Module User s Manual (Version1.1)
ICOP-6050F Embedded 386SX PC/104 CPU Module User s Manual (Version1.1) Copyright Notice This document is copyrighted, 2003 by ICOP Technology Inc. All rights are reserved. The information in the manual
ICOP-6053. Embedded 386SX PC/104 All-in-One CPU Module with 2S/ DOC/ 4M RAM onboard/ Ethernet User s Manual. (Version 3.1)
ICOP-6053 Embedded 386SX PC/104 All-in-One CPU Module with 2S/ DOC/ 4M RAM onboard/ Ethernet User s Manual (Version 3.1) Copyright Notice This document is copyrighted, 2000 by ICOP Technology Inc. All
Vortex86-6072. PC/104 Embedded Vortex86 CPU Module. User s Manual 64MB/2S/2USB/CRT/LCD/GPIO. (Revision 1.1)
Vortex86-6072 PC/104 Embedded Vortex86 CPU Module 64MB/2S/2USB/CRT/LCD/GPIO User s Manual (Revision 1.1) Copyright The information in this manual is subject to change without notice for continuous improvement
ICOP-6083 Series ICOP-6084 Series
ICOP-6083 Series ICOP-6084 Series Tiny Vortex86 I/O Modules Single LAN/DUAL LAN/Mini-PCI Audio-Video/Audio/Video User s Manual (Revision1.0) Copyright The information in this manual is subject to change
An0067. Cable-set Reference Guide. Rev. 2.0 - December 2007 - ETH_An0067_USM20-2007- 12
An0067 Cable-set Reference Guide Rev. 2.0 - December 2007 - ETH_An0067_USM20-2007- 12 2 Introduction Disclaimer The information in this manual has been carefully checked and is believed to be accurate.
CMT6104 IDE Controller and Hard Drive Carrier utilitymodule User s Manual
CMT6104 IDE Controller and Hard Drive Carrier utilitymodule User s Manual ISO9001 and AS9100 Certified BDM-610020013 Rev. A CMT6104 IDE Controller and Hard Drive Carrier utilitymodule User s Manual RTD
UMBC. ISA is the oldest of all these and today s computers still have a ISA bus interface. in form of an ISA slot (connection) on the main board.
Bus Interfaces Different types of buses: ISA (Industry Standard Architecture) EISA (Extended ISA) VESA (Video Electronics Standards Association, VL Bus) PCI (Periheral Component Interconnect) USB (Universal
NuIPC cpci- 3700 3U CompactPCI All-in-one Socket 370 CPU Module User s Guide
NuIPC cpci- 3700 3U CompactPCI All-in-one Socket 370 CPU Module User s Guide @Copyright 1999~2000 ADLINK Technology Inc. All Rights Reserved. Manual Rev. 1.10: 26 June 2000 The information in this document
ROCKY - 318 386SX SBC
ROCKY - 318 386SX SBC @Copyright 1997 All Rights Reserved. Manual first edition Nov.1,1997 The information in this document is subject to change without prior notice in order to improve reliability, design
Quick Installation. A Series of Intelligent Bar Code Reader with NeuroFuzzy Decoding. Quick Installation
Quick Installation A Series of Intelligent Bar Code Reader with NeuroFuzzy Decoding This chapter intends to get your new FuzzyScan scanner working with your existing system within minutes. General instructions
Network Appliance. Model Number SCB-6971. User s Manual. User s Manual
Network Appliance Model Number SCB-6971 Desktop AMD Geode LX800 Network Appliance with four LAN or three LAN and four switch, Mini PCI User s Manual Version 1.0 AEWIN Technologies Co., Ltd 1 Copyright
PCM-3346 Series. 486 DX66-based Module with SVGA/LCD/LAN Interface User's Manual
PCM-3346 Series 486 DX66-based Module with SVGA/LCD/LAN Interface User's Manual Copyright notice This document is copyright, 2000 and 2002, by Advantech Co., Ltd. All rights are reserved. The original
85MIV2 / 85MIV2-L -- Components Locations
Chapter Specification 85MIV2 / 85MIV2-L -- Components Locations RJ45 LAN Connector for 85MIV2-L only PS/2 Peripheral Mouse (on top) Power PS/2 K/B(underside) RJ45 (on top) +2V Power USB0 (middle) USB(underside)
PCM-3662 PC/104-plus Ethernet Module
PCM-3662 PC/104-plus Ethernet Module Introduction The PCM-3662 is a 10/100 Mbps Ethernet interface module that attaches to the PC/104-plus connector on your CPU card or PC/104-plus CPU module. The PCM-3662
Chapter 5 Cubix XP4 Blade Server
Chapter 5 Cubix XP4 Blade Server Introduction Cubix designed the XP4 Blade Server to fit inside a BladeStation enclosure. The Blade Server features one or two Intel Pentium 4 Xeon processors, the Intel
Products. CM-i586 Highlights. Página Web 1 de 5. file://c:\documents and Settings\Daniel\Os meus documentos\humanoid\material_o...
Página Web 1 de 5 The Home of the World's Best Computer-On-Module's Products Computer- On-Module's CM-X270 CM-X255 CM-iGLX CM-F82 CM-i686M CM-i686B CM-iVCF CM-i886 CM-i586 PC/104+ & ATX boards SBC-X270
DK40 Datasheet & Hardware manual Version 2
DK40 Datasheet & Hardware manual Version 2 IPC@CHIP DK40 Evaluation module Beck IPC GmbH http://www.bcl.de page 1 of 11 Table of contents Table of contents... 2 Basic description... 3 Characteristics...
General FAQ s E-Pos Systems.
General FAQ s E-Pos Systems. Q1. To install ELO touch screen, why does E-Touch Pro (B55 M/B) work fine in Windows but fail in DOS? Q2. Why can't the Touch screen driver work on Win XP? Q3. I installed
XPort Universal Demo Board User Guide
XPort Universal Demo Board User Guide Part Number 900-563 Revision A September 2009 Copyright and Trademark Contacts 2009 Lantronix. All rights reserved. No part of the contents of this book may be transmitted
Technical Information Jumpers, Connectors and Memory JXM7031 (7031-xxx) MicroATX Motherboard Dual Jasper Forest Processors
Technical Information Jumpers, Connectors and Memory JXM7031 (7031-xxx) MicroATX Motherboard Dual Jasper Forest Processors Dimension Diagram * = Pin 1 = Card Slots are on.800 centers Notes: All dimensions
PC/104 Specification
PC/104 Embedded Consortium www.pc104.org PC/104 Specification Version 2.6 October 13, 2008 Please Note This specification is subject to change without notice. While every effort has been made to ensure
Easy! Smooth! GP/ST-3500 Series->GP4000 Series Replacement Guidebook
Easy! Smooth! GP/ST-3500 Series->GP4000 Series Replacement Guidebook 1/46 The 6th Edition April 2013 Copyright 2013.4 Digital Electronics Corporation. All Rights Reserved. Preface This guidebook introduces
2-Port RS232/422/485 Combo Serial to USB2.0 Adapter (w/ Metal Case and Screw Lock Mechanism) Installation Guide
2-Port RS232/422/485 Combo Serial to USB2.0 Adapter (w/ Metal Case and Screw Lock Mechanism) Installation Guide 1. Introduction Thank you for purchasing this 2-Port RS232/422/485 Combo Serial to USB Adapter.
WIZ-Embedded WebServer User s Manual (Ver. 1.0)
[텍스트 입력] WIZ-Embedded WebServer User s Manual (Ver. 1.0) 2007 WIZnet Inc. All Rights Reserved. For more information, visit our website at www.wiznet.co.kr Document History Information Revision Data Description
Specifications for the Gateway M1300 Tablet PC
Specifications for the Gateway M1300 Tablet PC Specifications are subject to change without notice or obligation. Processor and Core Logic Processor options Chipset Processor packaging Level 2 cache Core
Web Site: www.parallax.com Forums: forums.parallax.com Sales: sales@parallax.com Technical: support@parallax.com
Web Site: www.parallax.com Forums: forums.parallax.com Sales: sales@parallax.com Technical: support@parallax.com Office: (916) 624-8333 Fax: (916) 624-8003 Sales: (888) 512-1024 Tech Support: (888) 997-8267
Mother Board Component
Mother Board Component Explain Introduction Mother Board Component 1.Clock Generator 2. CPU socket 3. Memory Socket Memory error checking 4. ROM Bios 5. CMOS Ram 6. Battery 7. Chipset 8. Expansion Slot
ALL-USB-RS422/485. User Manual. USB to Serial Converter RS422/485. ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
ALL-USB-RS422/485 USB to Serial Converter RS422/485 User Manual ALL-USB-RS422/485 USB to RS-422/485 Plugin Adapter This mini ALL-USB-RS422/485 is a surge and static protected USB to RS-422/485 Plugin Adapter.
LwLVision-USB 2.0. Installation Guide
LwLVision-USB 2.0 Installation Guide About this manual This manual has been carefully compiled and examined to the state-of-the-art. G&D neither explicitly nor implicitly takes guarantee or responsibility
2100 POS System. 2100 User Guide
2100 POS System 2100 User Guide Thank you for selecting UTC RETAIL s innovative Model 2100 Point of Sale solution! This guide is designed to acquaint you with the features and functionality of the 2100
Chapter 1. Getting Started Getting Started
Getting Started Chapter 1. Getting Started Getting Started Thank you for purchasing the MD-5000 M-ATX mainboard. The MD-5000 mainboard is based on SiS 648 North Bridge & 963 South Bridge chipsets for optimal
M68EVB908QL4 Development Board for Motorola MC68HC908QL4
M68EVB908QL4 Development Board for Motorola MC68HC908QL4! Axiom Manufacturing 2813 Industrial Lane Garland, TX 75041 Email: Sales@axman.com Web: http://www.axman.com! CONTENTS CAUTIONARY NOTES...3 TERMINOLOGY...3
PCA-6774. ISA Socket370 Slot PC, VGA/LCD/LVDS/LAN/CFC with optional second LAN and Gigabit LAN. User Manual
PCA-6774 ISA Socket370 Slot PC, VGA/LCD/LVDS/LAN/CFC with optional second LAN and Gigabit LAN User Manual i Copyright This document is copyrighted, 2005. All rights are reserved. The original manufacturer
8-Bit Microcontroller with Flash. Application Note. Using a Personal Computer to Program the AT89C51/C52/LV51/LV52/C1051/C2051
Using a Personal Computer to Program the ATC/C/LV/LV/C0/C0 Introduction This application note describes a personal computer-based programmer for the ATC/C/LV/LV/C0/C0 Flash-based s. The programmer supports
Data Cables. Schmitt TTL LABORATORY ELECTRONICS II
Data Cables Data cables link one instrument to another. Signals can attenuate or disperse on long wires. A direct wire works best for short cables of less than 10 ft. A TTL cable connection can use a Schmitt
If anything is damaged or missing, contact your dealer.
User Manual CS-62 Read this guide thoroughly and follow the installation and operation procedures carefully in order to prevent any damage to the units and/or any devices that connect to them. This package
Operator Touch Panel PC OTP/57V esom2586 / x86
Operator Touch Panel PC OTP/57V esom2586 / x86 3U Operator Touch Panel Device with 5.7 VGA LCD, Touch Screen, Embedded PC and Java 6 Product Information Description The OTP/57V is a compact PC-based open
USER GUIDE Programming Adapter Cable for Fujitsu Flash Microcontroller- F²MC-16LX/FR Family Fujitsu Microelectronics America, Inc.
USER GUIDE Programming Adapter Cable for Fujitsu Flash Microcontroller- F²MC-16LX/FR Family Fujitsu Microelectronics America, Inc. 1 Revision History Revision # Date Comment 1.0 03.25.2001 New Document
NOTICE. The information in this manual is subject to change without notice.
NOTICE TMC shall not be responsible for technical or editorial errors or omissions contained in this manual. TMC will not be liable for incidental or consequential damages resulting from the furnishing,
Advanced Data Capture and Control Systems
Advanced Data Capture and Control Systems Tronisoft Limited Email: sales@tronisoft.com Web: www.tronisoft.com RS232 To 3.3V TTL User Guide RS232 to 3.3V TTL Signal Converter Modules P/N: 9651 Document
TCP/IP MODULE CA-ETHR-A INSTALLATION MANUAL
TCP/IP MODULE CA-ETHR-A INSTALLATION MANUAL w w w. c d v g r o u p. c o m CA-ETHR-A: TCP/IP Module Installation Manual Page Table of Contents Introduction...5 Hardware Components... 6 Technical Specifications...
RN-WIFLY-EVAL-UM. WiFly Evaluation Kit. 2012 Roving Networks. All rights reserved. RN-WIFLY-EVAL-UM Version 1.32r 10/9/2012 USER MANUAL
WiFly Evaluation Kit 2012 Roving Networks. All rights reserved. Version 1.32r 10/9/2012 USER MANUAL OVERVIEW This document describes the hardware and software setup for Roving Networks evaluation kits,
RN-XV-RD2 Evaluation Board
RN-XV-RD2 Evaluation Board 2012 Roving Networks. All rights reserved. -1.01Version 1.0 9/28/2012 USER MANUAL OVERVIEW This document describes the hardware and software setup for Roving Networks RN-XV-RD2
RC2200DK Demonstration Kit User Manual
Demonstration Kit User Manual Table of contents TABLE OF CONTENTS... 1 QUICK INTRODUCTION... 2 INTRODUCTION... 3 DEMONSTRATION BOARD... 4 POWER SUPPLY SECTION... 5 RS-232 INTERFACE... 6 CONNECTORS... 7
LiveDesign Evaluation Board Technical Reference Manual. Technical reference manual for Altium s LiveDesign Evaluation Boards
LiveDesign Evaluation Board Technical Reference Manual Technical reference manual for Altium s LiveDesign Evaluation Boards CAUTION THIS EQUIPMENT INCLUDES EXPOSED ELECTRONIC COMPONENTS THAT ARE HIGHLY
Chapter 1. Getting Started Getting Started
Getting Started Chapter 1. Getting Started Getting Started Thank you for purchasing the MD-8080 M-ATX mainboard. The MD-8080 is based on Intel 865PE & Intel ICH5 chipsets for optimal system efficiency.
System Installation. 3-1 Socket 370 Celeron/Pentium-III Processor. Installing S370 CPU. Removing CPU. Configuring System Bus
System Installation This chapter provides you with instructions to set up your system. The additional information is enclosed to help you set up onboard PCI device and handle WDT operation in software
1 Mi kołaj Z Mik ar ołaj Z zyc arzy ki cki
1 Mikołaj Zarzycki NAND Flash SD Card Connector 256MB, 8bit I/F Push type, Up to 2GB/12.5Mbps USB Connector 1 x Device 2 x HOST, Dual-port LCD Module KEY Battery Holder 128 x 64 dots matrix structure 4
Block 3 Size 0 KB 0 KB 16KB 32KB. Start Address N/A N/A F4000H F0000H. Start Address FA000H F8000H F8000H F8000H. Block 2 Size 8KB 16KB 16KB 16KB
APPLICATION NOTE M16C/26 1.0 Abstract The following article describes using a synchronous serial port and the FoUSB (Flash-over-USB ) Programmer application to program the user flash memory of the M16C/26
16-Port RS232 to USB2.0 High Speed Multi Serial Adapter (w/ Metal Case) Installation Guide
16-Port RS232 to USB2.0 High Speed Multi Serial Adapter (w/ Metal Case) Installation Guide 1. Introduction Thank you for purchasing this 16-Port RS232 to USB2.0 High Speed Multi Serial Adapter. It is an
PCAN-MicroMod Evaluation Test and Development Environment for the PCAN-MicroMod. User Manual. Document version 2.0.1 (2013-08-06)
PCAN-MicroMod Evaluation Test and Development Environment for the PCAN-MicroMod User Manual Document version.0. (0-0-0) Products taken into account Product Name Part number Model PCAN-MicroMod Evaluation
2-port RS-232 High Speed Low Profile Universal PCI Serial Board
SER5037HL port RS3 High Speed Low Profile Universal PCI Serial Board Introduction SUNIX SER5037HL, Universal PCI serial communication board, allows users to add or expand two RS3 ports on PCbased system.
Lab Experiment 1: The LPC 2148 Education Board
Lab Experiment 1: The LPC 2148 Education Board 1 Introduction The aim of this course ECE 425L is to help you understand and utilize the functionalities of ARM7TDMI LPC2148 microcontroller. To do that,
RS-232/422/485, Power over Ethernet
IP-COM-M IP-COMi-M IP-COM-M PoE IP-COMi-M PoE RS-232 RS-232/422/485 RS-232, Power over Ethernet RS-232/422/485, Power over Ethernet Edition: September 2012 The computer programs provided with the hardware
Alcatel-Lucent OmniPCX Enterprise Communication Server TA-MMK (MMK V2)
Alcatel-Lucent OmniPCX Enterprise Communication Server TA-MMK (MMK V2) Legal notice: Alcatel, Lucent, Alcatel-Lucent and the Alcatel-Lucent logo are trademarks of Alcatel-Lucent. All other trademarks are
WP-8849. WinPAC-8x49 Series (WP-8149/8449/8849) is the new generation WinCE based InduSoft PAC (Programmable Automation Controller).
Tu Sitio de Automatización! WP-8149 WP-8449 Introduction: WP-8849 WinPAC-8x49 Series (WP-8149/8449/8849) is the new generation WinCE based InduSoft PAC (Programmable Automation Controller). It equips a
USBSPYDER08 Discovery Kit for Freescale MC9RS08KA, MC9S08QD and MC9S08QG Microcontrollers User s Manual
USBSPYDER08 Discovery Kit for Freescale MC9RS08KA, MC9S08QD and MC9S08QG Microcontrollers User s Manual Copyright 2007 SofTec Microsystems DC01197 We want your feedback! SofTec Microsystems is always on
JNIOR. Overview. Get Connected. Get Results. JNIOR Model 310. JNIOR Model 312. JNIOR Model 314. JNIOR Model 410
The INTEG is an Ethernet I/O (digital, analog) device that monitors and controls a small set of process signals. functions as both basic I/O for integration with another application or system AND as a
PC Notebook Diagnostic Card
www.winter-con.com User s Guide PC Notebook Diagnostic Card User s Guide 1 www.winter-con.com User s Guide INTRODUCTION Notebook Diagnostic Card is a powerful diagnostic tool for technicians and administrators
WinCON8000-R2/R8. Hardware User s Manual
WinCON8000-R2/R8 Compact Embedded Controller Hardware User s Manual REV 1.1 2004/10/22 1 Warranty All products manufactured by ICP DAS are warranted against defective materials for a period of one year
How To Configure Your Computer With A Microsoft X86 V3.2 (X86) And X86 (Xo) (Xos) (Powerbook) (For Microsoft) (Microsoft) And Zilog (X
System Configuration and Order-information Guide RX00 S4 February 008 Front View CD-ROM Drive (Optional) Hard Disk Bay Back View PCI Slot 0/00/000BASE-T connector Serial Port Display Mouse Keyboard Inside
PCAN-ISA. CAN Interface for ISA. User Manual
PCAN-ISA CAN Interface for ISA User Manual Products taken into account Product Name Model Item Number PCAN-ISA Single Channel One CAN channel IPEH-002074 PCAN-ISA Dual Channel Two CAN channels IPEH-002075
Eureka Technology. Understanding SD, SDIO and MMC Interface. by Eureka Technology Inc. May 26th, 2011. Copyright (C) All Rights Reserved
Understanding SD, SDIO and MMC Interface by Eureka Technology Inc. May 26th, 2011 Copyright (C) All Rights Reserved Copyright by Eureka Technology Inc. All Rights Reserved Introduction This white paper
EvB 5.1 v5 User s Guide
EvB 5.1 v5 User s Guide Page 1 Contents Introduction... 4 The EvB 5.1 v5 kit... 5 Power supply...6 Programmer s connector...7 USB Port... 8 RS485 Port...9 LED's...10 Pushbuttons... 11 Potentiometers and
USB / Data-Acquisition Module NOW LEAD-FREE
USB / Data-Acquisition Module NOW LEAD-FREE DLP-TEMP-G Features: Digital I/Os, Analog Inputs (0- Volts) or any combination USB. and.0 Compatible Interface th Generation Silicon from FTDI Supports Up To
Embedded & Industrial PCs International Products and Configurations INDEX
page 1 of 53 4 Embedded & Industrial PCs International Products and Configurations INDEX Introduction Index General Conditions Contact information Standard warranty conditions Return of goods for repair
HARDWARE MANUAL. BrightSign HD120, HD220, HD1020. BrightSign, LLC. 16795 Lark Ave., Suite 200 Los Gatos, CA 95032 408-852-9263 www.brightsign.
HARDWARE MANUAL BrightSign HD120, HD220, HD1020 BrightSign, LLC. 16795 Lark Ave., Suite 200 Los Gatos, CA 95032 408-852-9263 www.brightsign.biz TABLE OF CONTENTS OVERVIEW... 1 Block Diagram... 2 Ports...
SKP16C62P Tutorial 1 Software Development Process using HEW. Renesas Technology America Inc.
SKP16C62P Tutorial 1 Software Development Process using HEW Renesas Technology America Inc. 1 Overview The following tutorial is a brief introduction on how to develop and debug programs using HEW (Highperformance
2 Port KVM Switch. If anything is damaged or missing, contact your dealer.
2 Port KVM Switch User Manual CS-82A Read this guide thoroughly and follow the installation and operation procedures carefully in order to prevent any damage to the units and/or any devices that connect
LBNP16312. RS-232/485/422 serial device server. User manual
Tu Sitio de Automatización! LBNP16312 RS-232/485/422 serial device server User manual Summarize-----------------------------------------------------------------------------14-3 Package checklist---------------------------------------------------------------------14-3
How To Use A Sunix Ser5037A Card On A Pc Or Mac Or Mac With A Microsoft Powerbook (Powerbook) With A Powercard (Powercard) And Powercard With A Mini Usb (Powerboard) With An
SER5037A port RS3 Universal PCI Serial Board Introduction SUNIX SER5037A, Universal PCI serial communication board, allows users to add or expand two RS3 ports on PCbased system. The card is compatible
Trademarks. IBM, PC/AT, and PC/XT are trademarks of International Business Machines Corporation.
The information presented in this publication has been carefully checked for reliability; however, no responsibility is assumed for inaccuracies. Specifications are subject to change without notice. Trademarks
Hardware Reference. Linux Device Server IGW/922 with DIL/NetPC ADNP/9200
Linux Device Server IGW/922 with DIL/NetPC ADNP/9200 Hardware Reference SSV Embedded Systems Heisterbergallee 72 D-30453 Hannover Phone: +49 (0)511/40 000-0 Fax: +49 (0)511/40 000-40 E-mail: sales@ist1.de
Manual Serial PCI Cards
Manual Serial PCI Cards W&T Models 13011, 13410 13411, 13610 13611, 13812 Version 1.4 Subject to error and alteration 37 01/2005 by Wiesemann & Theis GmbH Subject to errors and changes: Since we can make
WHQL Certification Approval...2 User Interface...3 128K software FIFO 4 Universal PCI Interface...5 Ready for 64-bit System...5
0 INDEX WHQL Certification Approval...2 User Interface...3 128K software FIFO 4 Universal PCI Interface...5 Ready for 64-bit System...5 1.0 Introduction 6 2.0 Features.. 6 3.0 Hardware Guide... 7 3.1 System
M3 ORANGE Snap-On. User Guide. Product Model: A-SNO-ATYP-060-R00. Compatible Device: M3 ORANGE. Version 2.2 Released in March 2013
M3 ORANGE Snap-On User Guide Product Model: A-SNO-ATYP-060-R00 Compatible Device: M3 ORANGE Version 2.2 Released in March 2013 Contents Copyright and Agreement... 3 Notice. 4 Warnings and Cautions for
Thermostat Application Module Kit
Thermostat Application Module Kit PUG0040-00 Product User Guide Kit Contents Overview Thermostat Application Module CD-ROM: Software Examples and Documentation The Thermostat Application Module provides
3NNet KVM CP-104S /OSD / 19 KVM CP-108S / OSD / 19 KVM CP-116S / OSD / 19
3NNet USERS MANUAL KVM CP-104S /OSD / 19 KVM CP-108S / OSD / 19 KVM CP-116S / OSD / 19 RACK MOUNTABLE 4 / 8 / 16 PORT PS2 KVM SWITCH Rev 1.1 TABLE OF CONTENTS INTRODUCTION.. 3 FEATURES... 3 PACKAGE CONTENTS........
System Configuration and Order-information Guide ECONEL 100 S2. March 2009
System Configuration and Orderinformation Guide ECONEL 100 S2 March 2009 Front View DVDROM Drive 5 inch Bay Floppy Disk Drive Back View Mouse Keyboard Serial Port Display 10/100/1000BASET Connector Inside
ET-BASE AVR ATmega64/128
ET-BASE AVR ATmega64/128 ET-BASE AVR ATmega64/128 which is a Board Microcontroller AVR family from ATMEL uses MCU No.ATmega64 and ATmega128 64PIN. Board ET-BASE AVR ATmega64/128 uses MCU s resources on
nanoetxexpress Specification Revision 1.0 Figure 1 nanoetxexpress board nanoetxexpress 26.02.2009 Specification Rev 1.
nanoetxexpress Specification Revision 1.0 Figure 1 nanoetxexpress board Specification Rev 1.0 Page 1 of 12 Contents Figure 1 nanoetxexpress board...1 1. Introduction...3 2. Module Configuration...4 3.
Using GIGABYTE Notebook for the First Time
P55 V3.0 Congratulations on your purchase of the GIGABYTE Notebook. This manual will help you to get started with setting up your notebook. The final product configuration depends on the model at the point
ENET-710. ENET-710 - Ethernet Module ENET-710 JAN / 06 FOUNDATION
ENET-710 ENET-710 - Ethernet Module JAN / 06 ENET-710 FOUNDATION E N E T 7 1 0 ME smar www.smar.com Specifications and information are subject to change without notice. Up-to-date address information is
Cable Pinouts. SRP I/O Module
Cable Pinouts C This appendix lists the cables and connector pinout assignments for the cables used with the ERX-700 series and ERX-1400 series. Topic Page SRP I/O Module C-1 CT1 and CE1 I/O Modules C-4
SBC8600B Single Board Computer
SBC8600B Single Board Computer 720MHz TI s Sitara AM3359 ARM Cortex-A8 Microprocessor Onboard 512MByte DDR3 SDRAM and 512MByte NAND Flash UARTs, 2*USB Host and 1*OTG, 2*Ethernet, CAN, RS485, LCD/TSP, Audio,
CONSOLE REMOTE I /O AC 9V
CONSOLE CONSOLE REMOTE I /O AC 9V AC 9V REMOTE I /O User Manual CE-220 Read this guide thoroughly and follow the installation and operation procedures carefully in order to prevent any damage to the units
User Manual IC-485AI 2002-09-27
User Manual IC-485AI Note: This equipment has been tested and found to comply ith the limits for a Class A digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
Video Keyboard Mouse Audio automatic Switch CAS-241, CAS-441, CAS-441-PM
CAS-241, CAS-441, CAS-441-PM USER MANUAL Please read this manual and follow the installation procedure carefully to prevent any damage to the VKMA switch and/or to the connected devices. 2 Disclaimer We
PCAN-MicroMod Universal I/O Module with CAN Interface. User Manual. Document version 2.1.0 (2014-01-16)
PCAN-MicroMod Universal I/O Module with CAN Interface User Manual Document version 2.1.0 (2014-01-16) Products taken into account Product Name Part number Model PCAN-MicroMod IPEH-002080 with firmware
Orbit PCI Mk 2 Network Card. User Manual. Part No. 502566 Issue 4
Orbit PCI Mk 2 Network Card User Manual Part No. 502566 Issue 4 Information in this document is subject to change without notice. Companies, names and data used in examples herein are fictitious unless
LINDY ELECTRONICS LIMITED & LINDY-ELEKTRONIK GMBH - SECOND EDITION
RS-422/485 PCI Card User Manual English No. 51200 (2 Port) No. 51202 (4 Port) No. 51204 (8 Port) www.lindy.com LINDY ELECTRONICS LIMITED & LINDY-ELEKTRONIK GMBH - SECOND EDITION (Nov 2005) 1.0 Introduction
3.2 inch QVGA TFT Color LCD User s Guide Version 1 & 2
3.2 inch QVGA TFT Color LCD - User s Guide 3.2 inch QVGA TFT Color LCD User s Guide Version 1 & 2 Give graphics and to your application! EA2-USG-0701 v2.1 Rev A 3.2 inch QVGA TFT Color LCD - User s Guide
I/O Products IC697VSC096
I/O Products IC697VSC096 Single-Slot Celeron Socket 370 Processor-Based 814-000431-000 VMEbus Single-Board Computer January 2010 Features Celeron socket 370-based Single-Board Computer (SBC) with operating
Secu6 Technology Co., Ltd. Industrial Mini-ITX Intel QM77 Ivy Bridge Mobile Motherboard Support 3 rd Generation Core i7 / i5 / i3 Mobile Processor
ITX-QM77 Industrial Mini-ITX Intel QM77 Ivy Bridge Mobile Motherboard Support 3 rd Generation Core i7 / i5 / i3 Mobile Processor Datasheet 2012.09.19» Intel Ivy Bridge (IVB) 3rd Generation Core i3 / i5
USB-to-Serial RS-232 Hub USB-to-Serial RS-422/485 Hub USER MANUAL UC2322 / UC2324 / UC4852 / UC4854
USB-to-Serial RS-232 Hub USB-to-Serial RS-422/485 Hub USER MANUAL UC2322 / UC2324 / UC4852 / UC4854 FCC Information This equipment has been tested and found to comply with the limits for a Class B digital
MCB3101 (Class I) WiRobot Serial Bluetooth Wireless Module User Manual
MCB3101 (Class I) WiRobot Serial Bluetooth Wireless Module User Manual Version: 1.0.1 Dec. 2005 Table of Contents I. Introduction 2 II. Operations 2 II.1. Theory of Operation 2 II.2. Configuration (PC-PC
EasyPIC4 User s Manual
SOFTWARE AND HARDWARE SOLUTIONS FOR THE EMBEDDED WORLD MikroElektronika - Books - Compilers User s Manual PIC MICROCHIP DEVELOPMENT BOARD 3in1 mikro IN-CIRCUIT DEBUGGER USB 2.0 IN-CIRCUIT PROGRAMMER With
CP2110-EK CP2110 EVALUATION KIT USER S GUIDE. 1. Kit Contents. 2. Relevant Documentation. 3. Software Setup
CP2110 EVALUATION KIT USER S GUIDE 1. Kit Contents The CP2110 Evaluation Kit contains the following items: CP2110 Evaluation Board RS232 Serial Cable USB Cable DVD Quick Start Guide 2. Relevant Documentation
EZmoto V2. Product description Rev. 6 10/01/2014. EZmoto V2 Product description Rev.6 10/01/2014
EZmoto V2 Product description Rev. 6 10/01/2014 1 Contents 1. Overview... 3 2. Hardware Interface Description... 3 2.1 Main features of the EZmoto... 3 2.2 Hardware block diagram... 4 2.3 Internal Hardware
A+ Guide to Managing and Maintaining Your PC, 7e. Chapter 1 Introducing Hardware
A+ Guide to Managing and Maintaining Your PC, 7e Chapter 1 Introducing Hardware Objectives Learn that a computer requires both hardware and software to work Learn about the many different hardware components