EU Directives 1999/5/EC & 93/42/EEC: Compliance Information for Cisco Aironet AIR-(L)AP1131AG-E-K9 and AIR-(L)AP1242AG-E-K9 Products

Transcription

1 EU Directives 1999//EC & 93/4/EEC: Compliance Information for Cisco Aironet AIR-(L)AP1131AG-E-K9 and AIR-(L)AP14AG-E-K9 Products November 01 This document contains compliance information for wireless LAN products which are intended to be placed on the market within the European Union, Lichtenstein, Switzerland, Iceland, Norway, Turkey and other countries that have implemented the EU Directive 1999//EC and/or EU Directive 93/4/EEC Contents This document contains these sections: Scope, page 1 Declaration of Conformity with Regard to the EU Directive 1999//EC (R&TTE Directive), page CE Marking, page 4 Antennas, page 4 Changing Output Power, page 6 Changing Output Power, page 6 Obtaining Documents from Cisco.com, page Related Documentation, page 9 Scope The information in this document is applicable to the Cisco Aironet AIR-(L)AP1131AG-E-K9 and the AIR-(L)AP14AG-E-K9. The equipment operates in the,4 and the GHz bands. Americas Headquarters: Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA USA 007 Cisco Systems, Inc. All rights reserved.

2 Scope Declaration of Conformity with Regard to the EU Directive 1999//EC (R&TTE Directive) This declaration is only valid for configurations (combinations of software, firmware, and hardware, including antennas) provided and/or supported by Cisco Systems for use within the European Union, Lichtenstein, Switzerland, Iceland, Norway, Turkey or other countries that have implemented the EU Directives.

3 Scope Declaration of Conformity with Regard to the EU Directive 93/4/EEC (MDD) This device complies with the EMC requirements of the Medical Device Directive (MDD) 93/4/EEC. When installed in a medical environment, the equipment shall only be powered using PoE (Power over Ethernet). The full declaration of conformity for this product can be found in the Declarations of Conformity and Regulatory Information section of the appropriate product hardware installation guide, which is available on Cisco.com. See the Obtaining Documents from Cisco.com section on page for instructions for downloading these documents. 3

4 CE Marking The following standards were applied during the assessment of the product against the requirements of the Directives 1999//EC and 93/4/EEC: Radio: EN and EN EMC: EN and EN Safety: EN 6090 and EN 03 CE Marking For the Cisco Aironet AIR-(L)AP1131AG-E-K9 and the AIR-(L)AP14AG-E-K9, the following CE mark and Class- identifier are affixed to the equipment and its packaging. Intended Use of the Equipment The equipment is wireless LAN equipment that operates in the 400- to 43.-MHz band, and in the 10- to 30-MHz and 470- to 7-MHz bands. This equipment is for indoor use only! The maximum power level (EIRP) when operating in the.4 GHz band is 100 mw or 0 dbm. The maximum power level (EIRP) when operating in the MHz GHz band is 00 mw or 3 dbm. The maximum power level (EIRP) when operating in the MHz GHz band is 1000 mw or 30 dbm The regulatory limits for maximum output power are specified in EIRP. The EIRP level of a device can be calculated by adding the gain of the antenna used (specified in dbi) to the output power available at the connector (specified in dbm). Antennas AIR-(L)AP1131AG-E-K9 The dual band Wireless LAN product AIR-(L)AP1131AG-E-K9 has integrated antennas which cannot be removed or which are not user accessible. 4

5 Antennas AIR-(L)AP14AG-E-K9 The dual-band Wireless LAN product AIR-(L)AP14AG-E-K9 is equipped with with reversed polarity TNC antenna connectors for the use of dedicated antennas available from Cisco. Table 1 lists the.4-ghz antennas that can be used with this equipment, and Table lists the -GHz antennas that can be used. All antennas were assessed together with the equipment against the requirements of the R&TTE directive. It is the responsibility of the end user to select a power level that, together with the antenna, results in an EIRP (radiated power) level that is below the applicable limit. See the Intended Use of the Equipment section on page 4 to identify the regulatory limits for each frequency band.. Table 1.4-GHz Dedicated (external) Antennas and Maximum Allowed Conducted Power Settings Antenna Cisco Part Number Antenna Gain (dbi) Maximum Conducted Power Setting (dbm) (see note 1 ) Antenna Description AIR-ANT Dipole AIR-ANT POS diversity dipole AIR-ANT Diversity omni AIR-ANT17. 1 Ceiling mounted omni AIR-ANT06. 1 Mast mounted omni AIR-ANT Diversity omni AIR-ANT Wall mounted patch AIR-ANT Diversity patch AIR-ANT Hemispherical patch AIR-ANT410Y-R Yagi AIR-ANT Yagi AIR-ANT Omni AIR-ANT414S-R 14 7 Sector 1. The antenna gain mentioned does not include the cable loss. For all combinations, the total of power level, antenna gain and cable loss is equal to or below 0 dbm (EIRP). Table -GHz Dedicated Antennas and Maximum Allowed Conducted Power Settings Antenna Cisco Part Number Antenna Gain (dbi) Maximum Power Setting (dbm) Antenna Description AIR-ANT13-D-R 4 17 Dipole AIR-ANT14V-R Diversity omni

6 Changing Output Power Table -GHz Dedicated Antennas and Maximum Allowed Conducted Power Settings Antenna Cisco Part Number Antenna Gain (dbi) Maximum Power Setting (dbm) Antenna Description AIR-ANT160V-R 6 17 Omni AIR-ANT170P-R 7 14 Diversity patch AIR-ANT19P-R Patch Changing Output Power AIR-AP1131AG-E-K9 and AIR-AP14AG-E-K9 Connect your PC to the access point's Ethernet port and follow these steps to change the output power to meet the local regulations. Step 1 Step Step 3 Open your Internet browser. You must use Microsoft Internet Explorer.x or later. Enter the access point's IP address in the browser address line and press Enter. An Enter Network Password screen appears. Enter the username and password and press Enter. The Summary Status page appears. The default username and password are both Cisco. They are case-sensitive. Step 4 Step Step 6 Step 7 In the Network Interfaces section, select the radio you want to change. The status page for that radio appears. Select the Settings tab. The Settings page appears. Scroll down to the Transmitter Power section. Select the appropriate power level. Table 3 lists the output power levels (conducted) for the.4-ghz and -GHz bands. Table 3 Available Output Power Levels 0.11b/g.4-GHz Radio (dbm) a -GHz Radio (dbm)

7 Changing Output Power Step Click Apply. See the hardware installation guide or the quick start guide for your product for more details on how to connect your PC to the access point and on how to configure your access point using the web-browser interface. AIR-LAP1131AG-E-K9 and AIR-LAP14AG-E-K9 The output power on the AIR-LAP1131AG-E-K9 and the AIR-LAP14AG-E-K9 access points can be changed only using a Cisco Wireless LAN Controller. See the WLC configuration guide for more details on how to to configure your access point using the web-browser interface. Follow these steps to change the AIR-LAP1131AG-E-K9 or the AIR-LAP14AG-E-K9 access point s output power to meet local regulations: Step 1 Step Step 3 Step 4 Connect your access point to the Ethernet network to register with your controller. Open your Internet browser. You must use Microsoft Internet Explorer or later. Enter address (where IP address is the controller s IP address) in the browser address line and press Enter. A user login screen appears. Enter the username and password and press Enter. The controller s summary page appears. The username and password are case-sensitive. Step Step 6 Click Wireless > Access Point > 0.11a Radios or 0.11b/g Radios > Cisco APs > Configure. The radio settings page appears. Scroll down to the Tx Power Level Assignment field, and select Global or Custom. Global indicates that the radio output power is globally controlled by settings in the controller s global RF parameters section. Custom indicates that the radio output power is manually controlled by the Tx Power Configuration setting field. Step 7 In the Tx Power Level field, select the appropriate power level setting (1 to ). Based on the configured antenna gain, the configured channel, and the configured power level, the actual transmit power at the access point can be reduced so that the specific country regulations are not exceeded. Table 4 lists the Cisco Wireless LAN Controller power settings and the output power levels for the.4-ghz and -GHz bands. 7

8 Obtaining Documents from Cisco.com Table 4 Available Output Power Levels Cisco Wireless LAN Controller Tx Power Settings 1 1 (maximum) b/g.4-GHz Radio (dbm) n/a n/a 0.11a -GHz Radio (dbm) n/a 1. The Tx Power Level setting of 1 represents the maximum conducted power setting for the access point. Each subsequent power level (such as, 3, 4, etc) represents approximately a 3-dBm reduction in transmit power from the previous power level. Step Close your Internet browser. Obtaining Documents from Cisco.com Follow these steps to obtain any of the documentation mentioned in this document. Step 1 Step Step 3 Browse to Cisco s Software Center: For Cisco Aironet access point documents, click Cisco Aironet 1130AG Series, Cisco Aironet 100 Series, or Cisco Aironet 140AG Series in the Wireless LAN Access section. For Cisco Wireless LAN Controller documents, click Cisco 4400 Series Wireless LAN Controllers or Cisco 000 Series Wireless LAN Controllers. Select the appropriate document. The AIR-RM1/ radio modules are covered in the Cisco Aironet 100 series documents. If you still have questions regarding the compliance of these products or you cannot find the information you are looking for, please send an to Cisco at complianceinfo@cisco.com

9 Related Documentation Related Documentation These documents provide information about the controllers and access points: Cisco Wireless LAN Controller Configuration Guide describes installation, configuration, and logging into Cisco Wireless LAN Controllers. Cisco Aironet lightweight access point hardware installation guides describe the access point s hardware installation and specifications. 9

10 Related Documentation This document is to be used in conjunction with the documents listed in the Related Documentation section. Cisco and the Cisco Logo are trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S. and other countries. A listing of Cisco's trademarks can be found at Third party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (100R) 01 Cisco Systems, Inc. All rights reserved. 10