INSTALLATION AND ADMINISTRATION GUIDE. Cisco Small Business. Camera Accessories

Transcription

1 INSTALLATION AND ADMINISTRATION GUIDE Cisco Small Business Camera Accessories

2 Cisco and the Cisco Logo are trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S. and other countries. A listing of Cisco's trademarks can be found at Third party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1005R) 010 Cisco Systems, Inc. All rights reserved B0

3 Contents Chapter 1: About This Document 5 Before You Begin 5 Lens Specifications 6 Enclosure Specifications 7 Cisco PVC300 Enclosure Accessory Specifications 8 Warnings and Precautions 10 Statement 1071 Warning Definition 10 Where To Go Next 16 Chapter : Accessory Installation Processes 17 Installing a Lens 17 Installing the PVC300/WVC300 Cameras in a VC 00 Enclosure 19 Before You Begin 19 Preparing the Enclosure Preparing the Brackets 3 Connecting the Cables 3 Attaching the Camera to the Camera Platform 3 Building the Enclosure 33 Mounting the Enclosure 35 Installing the Cisco PVC300 in a Cisco VC 030 Enclosure 37 Before You Begin 37 Assembling the Enclosure 39 Securing the Power Adaptor 43 Where to Go Next 43 Installing the Cisco VC 03 Corner Mount Adapter 44 Installing the Cisco VC 033 Pole Mount Adapter 47 Installing the VC0 Cameras in a VC 05 Enclosure 50 Before You Begin 50 Preparing the Enclosure 50 Installing the Enclosure 53 Camera Accessories Installation and Administration Guide 3

4 Contents Appendix A: Specifications 57 Cisco CAMLWA (Computar 1/3-inch.3 mm Wide Angle Lens) 57 Cisco CAMLMI (Tamron 1/3-inch 3-8 mm Varifocal.7X Zoom Lens) 58 Cisco VC 00 (Camera Exterior Enclosure with Heater and Blower for the Cisco PVC300/WVC300) 58 Cisco VC 030 (Camera Enclosure Exterior Pan Tilt for the Cisco PVC300)60 Cisco VC 05 (Indoor Recessed Ceiling Mount Kit for the Cisco VC0) 6 Appendix B: Where to Go From Here 64 Camera Accessories Installation and Administration Guide 4

5 1 About This Document The Cisco Small Business Internet Video Cameras provide high quality monitoring that can be optimized for many different applications. This document describes the installation of various camera accessories that can be used with the Cisco PVC300, WVC300, and PVC300 cameras. Before You Begin This document assumes that you have previously installed and configured your camera or cameras. For installation instructions, go to smallbizcameras for the Quick Installation Guide or the Administration Guide for your particular Cisco camera model. Datasheets are also available for your cameras and accessories on the same website. The following Cisco cameras can use the accessories described in this document: PVC300 Cisco Small Business Internet Video Camera with Audio and POE WVC300 Cisco Small Business Wireless-G Internet Video Camera with Audio PVC300 Cisco Small Business PTZ Internet Camera with Audio and POE VC0 Cisco VC0 Dome Wide Dynamic Range (WDR) Day/Night PoE Network Camera Please check for compatibility if your camera is not included in this list. Camera Accessories Installation and Administration Guide 5

6 About This Document Lens Specifications 1 Lens Specifications The following lenses can be used with the Cisco PVC300 and WVC300 cameras: Cisco Lens Model Number CIVS-IPC-VT38 CIVS-IPC-VT31 CIVS-IPC-VT55 CIVS-IPC-VF38 CIVS-IPC-VF31 CIVS-IPC-VF55 CAMLMI Camera Lens Description Tamron 3-8 mm Varifocal Lens, CS Mount Tamron 3-11 mm Varifocal Lens, CS Mount Tamron 5-50 mm Varifocal Lens, CS Mount Fujinon 3-8 mm Varifocal Lens, CS Mount Fujinon 3-11 mm Varifocal Lens, CS Mount Fujinon 5-50 mm Varifocal Lens, CS Mount Tamron 1/3-inch 3-8 mm Varifocal.7X Zoom Lens, CS Mount. For installation instructions, see Installing a Lens, page 17. CAMLWA Computar 1/3-inch.3 mm Wide Angle Lens. For installation instructions, see Installing a Lens, page 17. Camera Accessories Installation and Administration Guide 6

7 About This Document Enclosure Specifications 1 Enclosure Specifications The following enclosures can be used with the Cisco PVC300, WVC300, PVC300, and VC0 IP cameras: Cisco Camera Cisco Enclosure Model Number Enclosure Name Description PVC300/ WVC300 VC 00 Exterior Camera Enclosure with Defroster and Blower IP55 Certified outdoor enclosure with defroster and blower provides protection against small particles and splashing water. PVC300 VC 030 Camera Enclosure Exterior Pan Tilt Dome enclosure with wallmounting bracket and power adapter. Camera Accessories Installation and Administration Guide 7

8 About This Document Enclosure Specifications 1 Cisco Camera Cisco Enclosure Model Number Enclosure Name Description VC0 VC 05 Cisco VC 05 Indoor Ceiling Mount Kit Indoor recessed ceiling mount kit specifically designed to work with the Cisco VC0 Network Camera. The recessed feature reduces the area of the camera body that is below the ceiling. The cover is especially useful in false ceiling applications. NOTE: The three holes on the front of the cover indicate the microphone. Cisco PVC300 Enclosure Accessory Specifications The following items can be used with the VC 030 dome enclosure for the PVC300 camera: Cisco VC 030 Accessory Model Number CAB-AC-C5-US= CAB-AC-C5-UK= CAB-AC-C5-EUR= CAB-AC-C5-AUS= Accessory Name Localized Power Cord Description A power cord is not included with the VC 030 enclosure but is required for operation. Select the appropriate power cord based on regional requirements. Camera Accessories Installation and Administration Guide 8

9 About This Document Enclosure Specifications 1 Cisco VC 030 Accessory Model Number VC 031 Accessory Name Camera Exterior Pan Tilt Pendant Mounting Adapter Description Pendant mounting adapter for VC 030 includes ceiling mount and two pendant poles. VC 03 Camera Exterior Pan Tilt Corner Mounting Adapter Corner mount adapter used with the VC 030 to mount the PVC300 on the corner of a building. VC 033 Camera Exterior Pan Tilt Pole Mounting Adapter Pole mount adapter used with the VC 030 to mount the PVC300 on a pole. NOTE Before installing a surveillance system, check with local government agencies to determine if video surveillance and audio monitoring are permitted in your area. Camera Accessories Installation and Administration Guide 9

10 About This Document Warnings and Precautions 1 Warnings and Precautions Statement 1071 Warning Definition Warning IMPORTANT SAFETY INSTRUCTIONS This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. Use the statement number provided at the end of each warning to locate its translation in the translated safety warnings that accompanied this device. Statement 1071 SAVE THESE INSTRUCTIONS Waarschuwing BELANGRIJKE VEILIGHEIDSINSTRUCTIES Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die lichamelijk letsel kan veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust te zijn van de bij elektrische schakelingen betrokken risico's en dient u op de hoogte te zijn van de standaard praktijken om ongelukken te voorkomen. Gebruik het nummer van de verklaring onderaan de waarschuwing als u een vertaling van de waarschuwing die bij het apparaat wordt geleverd, wilt raadplegen. BEWAAR DEZE INSTRUCTIES Varoitus TÄRKEITÄ TURVALLISUUSOHJEITA Tämä varoitusmerkki merkitsee vaaraa. Tilanne voi aiheuttaa ruumiillisia vammoja. Ennen kuin käsittelet laitteistoa, huomioi sähköpiirien käsittelemiseen liittyvät riskit ja tutustu onnettomuuksien yleisiin ehkäisytapoihin. Turvallisuusvaroitusten käännökset löytyvät laitteen mukana toimitettujen käännettyjen turvallisuusvaroitusten joukosta varoitusten lopussa näkyvien lausuntonumeroiden avulla. SÄILYTÄ NÄMÄ OHJEET Attention IMPORTANTES INFORMATIONS DE SÉCURITÉ Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une situation pouvant entraîner des blessures ou des dommages corporels. Avant de travailler sur un équipement, soyez conscient des dangers liés aux circuits électriques et familiarisez-vous avec les procédures couramment utilisées pour éviter les accidents. Pour prendre connaissance des traductions des avertissements figurant dans les consignes de sécurité traduites qui accompagnent cet appareil, référez-vous au numéro de l'instruction situé à la fin de chaque avertissement. CONSERVEZ CES INFORMATIONS Camera Accessories Installation and Administration Guide 10

11 About This Document Warnings and Precautions 1 Warnung WICHTIGE SICHERHEITSHINWEISE Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu Verletzungen führen kann. Machen Sie sich vor der Arbeit mit Geräten mit den Gefahren elektrischer Schaltungen und den üblichen Verfahren zur Vorbeugung vor Unfällen vertraut. Suchen Sie mit der am Ende jeder Warnung angegebenen Anweisungsnummer nach der jeweiligen Übersetzung in den übersetzten Sicherheitshinweisen, die zusammen mit diesem Gerät ausgeliefert wurden. BEWAHREN SIE DIESE HINWEISE GUT AUF. Avvertenza IMPORTANTI ISTRUZIONI SULLA SICUREZZA Questo simbolo di avvertenza indica un pericolo. La situazione potrebbe causare infortuni alle persone. Prima di intervenire su qualsiasi apparecchiatura, occorre essere al corrente dei pericoli relativi ai circuiti elettrici e conoscere le procedure standard per la prevenzione di incidenti. Utilizzare il numero di istruzione presente alla fine di ciascuna avvertenza per individuare le traduzioni delle avvertenze riportate in questo documento. CONSERVARE QUESTE ISTRUZIONI Advarsel VIKTIGE SIKKERHETSINSTRUKSJONER Dette advarselssymbolet betyr fare. Du er i en situasjon som kan føre til skade på person. Før du begynner å arbeide med noe av utstyret, må du være oppmerksom på farene forbundet med elektriske kretser, og kjenne til standardprosedyrer for å forhindre ulykker. Bruk nummeret i slutten av hver advarsel for å finne oversettelsen i de oversatte sikkerhetsadvarslene som fulgte med denne enheten. TA VARE PÅ DISSE INSTRUKSJONENE Aviso INSTRUÇÕES IMPORTANTES DE SEGURANÇA Este símbolo de aviso significa perigo. Você está em uma situação que poderá ser causadora de lesões corporais. Antes de iniciar a utilização de qualquer equipamento, tenha conhecimento dos perigos envolvidos no manuseio de circuitos elétricos e familiarize-se com as práticas habituais de prevenção de acidentes. Utilize o número da instrução fornecido ao final de cada aviso para localizar sua tradução nos avisos de segurança traduzidos que acompanham este dispositivo. GUARDE ESTAS INSTRUÇÕES Advertencia! INSTRUCCIONES IMPORTANTES DE SEGURIDAD Este símbolo de aviso indica peligro. Existe riesgo para su integridad física. Antes de manipular cualquier equipo, considere los riesgos de la corriente eléctrica y familiarícese con los procedimientos estándar de prevención de accidentes. Al final de cada advertencia encontrará el número que le ayudará a encontrar el texto traducido en el apartado de traducciones que acompaña a este dispositivo. GUARDE ESTAS INSTRUCCIONES Camera Accessories Installation and Administration Guide 11

12 About This Document Warnings and Precautions 1 Varning! VIKTIGA SÄKERHETSANVISNINGAR Denna varningssignal signalerar fara. Du befinner dig i en situation som kan leda till personskada. Innan du utför arbete på någon utrustning måste du vara medveten om farorna med elkretsar och känna till vanliga förfaranden för att förebygga olyckor. Använd det nummer som finns i slutet av varje varning för att hitta dess översättning i de översatta säkerhetsvarningar som medföljer denna anordning. SPARA DESSA ANVISNINGAR Camera Accessories Installation and Administration Guide 1

13 About This Document Warnings and Precautions 1 Aviso INSTRUÇÕES IMPORTANTES DE SEGURANÇA Este símbolo de aviso significa perigo. Você se encontra em uma situação em que há risco de lesões corporais. Antes de trabalhar com qualquer equipamento, esteja ciente dos riscos que envolvem os circuitos elétricos e familiarize-se com as práticas padrão de prevenção de acidentes. Use o número da declaração fornecido ao final de cada aviso para localizar sua tradução nos avisos de segurança traduzidos que acompanham o dispositivo. GUARDE ESTAS INSTRUÇÕES Advarsel VIGTIGE SIKKERHEDSANVISNINGER Dette advarselssymbol betyder fare. Du befinder dig i en situation med risiko for legemesbeskadigelse. Før du begynder arbejde på udstyr, skal du være opmærksom på de involverede risici, der er ved elektriske kredsløb, og du skal sætte dig ind i standardprocedurer til undgåelse af ulykker. Brug erklæringsnummeret efter hver advarsel for at finde oversættelsen i de oversatte advarsler, der fulgte med denne enhed. GEM DISSE ANVISNINGER Camera Accessories Installation and Administration Guide 13

14 About This Document Warnings and Precautions 1 Camera Accessories Installation and Administration Guide 14

15 About This Document Warnings and Precautions 1 WARNING Only trained and qualified personnel should be allowed to install, replace, or service this equipment. Statement 1030 WARNING No user-serviceable parts inside. Do not open. Statement 1073 Camera Accessories Installation and Administration Guide 15

16 About This Document Where To Go Next 1 Where To Go Next The installation process for lenses and enclosures are discussed in Accessory Installation Processes, page 17. Camera Accessories Installation and Administration Guide 16

17 Accessory Installation Processes The following procedures help you install your Cisco camera accessories. Installing a Lens, page 17 Installing the PVC300/WVC300 Cameras in a VC 00 Enclosure, page 19 Installing the Cisco PVC300 in a Cisco VC 030 Enclosure, page 37 Installing the Cisco VC 03 Corner Mount Adapter, page 44 Installing the Cisco VC 033 Pole Mount Adapter, page 47 Installing the VC0 Cameras in a VC 05 Enclosure, page 50 Installing a Lens Follow the instructions below to replace the Cisco PVC300 or WVC300 camera lens with any C- or CS-mount lens. STEP 1 STEP Unscrew the current lens on your Cisco PVC300 or WVC300 IP camera. Ensure that the new lens is clean because any dirt may degrade the quality of video images. Save the lens opening dust cap and replace the dust cap if you remove the lens. Camera Accessories Installation and Administration Guide 17

18 Installing a Lens STEP 3 Screw the new lens onto the opening of the camera. The camera accepts both C- and CS-mount lenses. If you are using a CS-mount lens, screw the lens into the lens opening. If you are using the C-mount lens then you need to use the C-mount 5 mm lens adapter ring. The adapter ring is included with the camera. If you are using a DC auto iris lens, connect its cable to the DC auto iris lens connector on the IP camera. The illustrations below show the location of the connector on the IP camera. STEP 4 STEP 5 If you have a manual iris lens, adjust the iris according to the prevailing light conditions. Adjust the focus of your lens. Turn the lens slowly either clockwise or counterclockwise until the desired image appears. Do not turn the lens too far in either direction. Camera Accessories Installation and Administration Guide 18

19 Installing the PVC300/WVC300 Cameras in a VC 00 Enclosure Installing the PVC300/WVC300 Cameras in a VC 00 Enclosure Follow the instructions below to install a Cisco PVC300 or WVC300 camera into a Cisco VC 00 enclosure. Please note that the Cisco WVC300 camera must be wired to be used in the enclosure. Wireless mode is not supported. Before You Begin If you plan to install this camera into a tropical, coastal, saltwater, or corrosive industrial water/moist environment, seal each stainless steel screw and fitting with a silicon grease compound. This compound prevents corrosion and extends the life span of the camera and the housing. STEP 1 Organize the components of the VC 00 enclosure unit: Camera Accessories Installation and Administration Guide 19

20 Installing the PVC300/WVC300 Cameras in a VC 00 Enclosure Included Parts Enclosure cover and base Wall mount bracket Enclosure bracket Two accessory kits, which includes the following: Accessory Kit Parts, For Bracket Number of Items Anchor 3 Hexagonal stainless steel screws 3 Stainless steel washers 4 Nylon washers 4 L-type hex wrench 1 Allen wrench 1 Accessory Kit Parts, For Camera Number of Items Plastic pad Plastic washer 1 Hexagonal stainless steel screw 1/4 x 3/8 1 Hexagonal stainless steel screw 1/4 x 1/ 1 Stainless washers 1 Required Tools and Parts (Not Included) RJ45 plug Wire stripper or RJ45 crimping tool 10 mm wrench or socket Network cable tester Camera Accessories Installation and Administration Guide 0

21 Installing the PVC300/WVC300 Cameras in a VC 00 Enclosure Optional Tools and Parts (Not Included) Plastic pipe or conduit for protecting cords and cables STEP Familiarize yourself with the internal components of the enclosure. STEP 3 NOTE Set up and focus your camera before placing it in the enclosure. When it is in the enclosure, you can t make any more adjustments. Refer to the PVC300 and WVC300 Administration Guide for setup instructions. The Cisco WVC300 camera must be wired to be used in the enclosure. Wireless mode is not supported. Camera Accessories Installation and Administration Guide 1

22 Installing the PVC300/WVC300 Cameras in a VC 00 Enclosure Preparing the Enclosure STEP 1 STEP Use the provided wrench to remove the four screws that attach the enclosure cover to the base. Lift the enclosure cover off the base. STEP 3 Use the provided wrench to release the four keyhole screws, then slide the camera platform to withdraw it from the enclosure base. STEP 4 Use the supplied L-type hex wrench to detach the rectangular support from the camera platform. The rectangular support is required only during shipping. Camera Accessories Installation and Administration Guide

23 Installing the PVC300/WVC300 Cameras in a VC 00 Enclosure Preparing the Brackets This procedure describes how to connect the mounting bracket and the enclosure bracket. STEP 1 STEP STEP 3 Using the L-type hex wrench, adjust the ball joint in the enclosure bracket to set the approximate direction the enclosure. Place the wall mount bracket and the enclosure bracket together. Screw the brackets together using the provided stainless steel screw and L-type hex wrench. Connecting the Cables Before completing this procedure, you must cut the camera s Ethernet cable and the power cord as it will be necessary to feed them through the mounting brackets and the cable conduits found on the bottom of the enclosure. WARNING Equipment connected to outdoor cameras must be permanently grounded in accordance with national and local codes. Statement 374 WARNING Hazardous voltages may be present in the outdoor camera cables under fault conditions. Disconnect all cables from the outdoor cameras before servicing this equipment. Statement 376 WARNING Do not use this product near water; for example, near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement, or near a swimming pool. Statement 1035 WARNING Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations. Statement 1036 Camera Accessories Installation and Administration Guide 3

24 Installing the PVC300/WVC300 Cameras in a VC 00 Enclosure WARNING Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface. Statement 1037 WARNING Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning. Statement 1038 STEP 1 STEP Feed the cut Ethernet cable and power cord through the brackets. Feed the Ethernet cable and power cord through the conduits found on the bottom of the enclosure. The power cord goes through the conduit closest to the power supply wiring. WARNING When stranded wiring is required, use approved wiring terminations, such as closed-loop or spade-type with upturned lugs. These terminations should be the appropriate size for the wires and should clamp both the insulation and conductor. Statement 100 WARNING Use copper conductors only. Statement 105 Camera Accessories Installation and Administration Guide 4

25 Installing the PVC300/WVC300 Cameras in a VC 00 Enclosure STEP 3 Add the ferrite core on the power cord. STEP 4 Add the ferrite core on the Ethernet cable. Camera Accessories Installation and Administration Guide 5

26 Installing the PVC300/WVC300 Cameras in a VC 00 Enclosure STEP 5 Connect the power cord to the terminal block assembly. You can make these connections in one of two ways: color matching the wires, or using a multimeter to measure resistance from the power cord and the terminal block assembly. WARNING This equipment has been designed for connection to TN and IT power systems. Statement 1007 WARNING This equipment must be grounded. Never defeat the ground conductor or operate the equipment in the absence of a suitably installed ground conductor. Contact the appropriate electrical inspection authority or an electrician if you are uncertain that suitable grounding is available. Statement 104 WARNING When installing or replacing the unit, the ground connection must always be made first and disconnected last. Statement 1046 WARNING Use copper conductors only. Statement 105 WARNING The ground connection from the power cable MUST connect to the chassis first. The power cord ground wire must connect to the chassis ground terminal first. A closed loop connector must be attached to the ground and then attached to the screw and lock washer at the protective earth ground (PE). Camera Accessories Installation and Administration Guide 6

27 Installing the PVC300/WVC300 Cameras in a VC 00 Enclosure To color match the wires It is highly recommended that the installer references an IEC standard wiring diagram, such as those found at If you are using a multimeter, and you have a properly labeled power cord, you can use the multimeter to register the resistance from the prongs. The following is an illustration of a labeled European AC power cord plug head, showing Live, Earth, Neutral. If you are using a multimeter, the matched wire and plug will show resistance; mismatched will read OL (overload). By testing, the labeled plug pin on the cross-section indicates the exact wire, which you can then directly match on the enclosure power block assembly. The following is an illustration of a multimeter measuring the polarity of the wires. Camera Accessories Installation and Administration Guide 7

28 Installing the PVC300/WVC300 Cameras in a VC 00 Enclosure The following illustration shows the power cord attaching to the terminal block assembly. Note that the power cord ground wire (green/yellow in this case) does not connect to the terminal block; the ground connects directly to the chassis. Camera Accessories Installation and Administration Guide 8

29 Installing the PVC300/WVC300 Cameras in a VC 00 Enclosure The following illustration shows the power cord ground wire (green/yellow in this case) directly connecting to the enclosure chassis. Camera Accessories Installation and Administration Guide 9

30 Installing the PVC300/WVC300 Cameras in a VC 00 Enclosure STEP 6 Prepare to clamp the Ethernet cable with an RJ45 plug. To make the proper connections, refer to the following illustration that provides color mapping for the cable wires. STEP 7 STEP 8 Use the RJ45 crimping tool to clamp the plug to the wires. Use a network cable tester to test the Ethernet connections. Camera Accessories Installation and Administration Guide 30

31 Installing the PVC300/WVC300 Cameras in a VC 00 Enclosure STEP 9 Make any other I/O connections to the terminal block assembly (optional). Pin 1,, 3 and 4 are DC 1C outputs for motor lenses, IR illuminators, sirens or speakers Pins 5 and 6 are DC1V outputs for cameras NOTE If a pin is not in use, remove the cable from the connector. Camera Accessories Installation and Administration Guide 31

32 Installing the PVC300/WVC300 Cameras in a VC 00 Enclosure Attaching the Camera to the Camera Platform In this procedure, you will attach the camera to the camera platform in the enclosure. STEP 1 From the accessory kit, remove a rectangular plastic pad and a steel washer. The pad and the washer are pictured below. STEP STEP 3 STEP 4 Turn the camera upside down and find the mounting hole. Place the plastic pad over the mounting hole. Remove the screw from the camera platform. Place the washer on top of the camera platform, followed by the screw. STEP 5 Align the screw holes of the camera and camera platform. Camera Accessories Installation and Administration Guide 3

33 Installing the PVC300/WVC300 Cameras in a VC 00 Enclosure STEP 6 Use the supplied L-type hex wrench to secure the camera platform to the camera. Building the Enclosure STEP 1 Use the small wrench to secure the camera platform onto the enclosure base. TIP Make sure that the camera is firmly attached to the enclosure base and that the camera is as close to the front (glass) of the enclosure as possible. Camera Accessories Installation and Administration Guide 33

34 Installing the PVC300/WVC300 Cameras in a VC 00 Enclosure STEP Connect the Ethernet cable and power cord to the camera. STEP 3 Place the enclosure back over the sled and replace all screws. Camera Accessories Installation and Administration Guide 34

35 Installing the PVC300/WVC300 Cameras in a VC 00 Enclosure Mounting the Enclosure STEP 1 Use the rear section of the wall mount bracket (1) as a template to mark the mounting holes on the wall. STEP Attach the main enclosure to the brackets with the supplied four 1/4-inch screws (). Camera Accessories Installation and Administration Guide 35

36 Installing the PVC300/WVC300 Cameras in a VC 00 Enclosure STEP 3 Feed the cables from the enclosure and mounting brackets through the concealed cable channel found underneath the wall mount bracket (3). STEP 4 STEP 5 Secure the brackets and enclosure to the wall with the supplied plastic anchors and screws. Using the L-type hex wrench, adjust the ball joint in the enclosure bracket to set the final direction of the enclosure (4). STEP 6 (Optional) Plastic pipe or conduit should be used to waterproof and protect the cables and cords. Camera Accessories Installation and Administration Guide 36

37 Installing the Cisco PVC300 in a Cisco VC 030 Enclosure Installing the Cisco PVC300 in a Cisco VC 030 Enclosure Follow the instructions below to install a Cisco PVC300 camera into a Cisco VC 030 enclosure. These instructions also cover using the optional Cisco VC 031 Pendant Mounting Adapter. Before You Begin If you plan to install this camera into a tropical, coastal, saltwater, or corrosive industrial water/moist environment, seal each stainless steel screw and fitting with a silicon grease compound. This compound prevents corrosion and extends the life span of the camera and the housing. STEP 1 Organize the following components of the VC 030 enclosure unit: Included Parts Enclosure Enclosure cover Wall mount bracket Power supply Camera cable Camera Accessories Installation and Administration Guide 37

38 Installing the Cisco PVC300 in a Cisco VC 030 Enclosure Cross iron plate and screws Required Tools and Parts (Not Included) Phillips-head screwdriver Power cord. See the Cisco PVC300 Enclosure Accessory Specifications section for ordering information. Optional Tools and Parts (Not Included) Extension cord Custom length, -core copper conductor, type SPT-1 (UL/ CSA style), 18 AWG, texture x 0.84 mm², withstand 105 C, and 300V Electrical Junction Box Protection level IP66 or above; inner size at least W151 mm x L118 mm x H38 mm; material should be aluminium alloy Plastic pipe or conduit for protecting cords and cables STEP Organize the following (optional) components of the Cisco VC 031 Pendant Mounting Adapter. The mounting adapter can be used alone or with one or more pendant poles. Included Parts Mounting Adapter with Pendant Pole(s) Camera Accessories Installation and Administration Guide 38

39 Installing the Cisco PVC300 in a Cisco VC 030 Enclosure Assembling the Enclosure WARNING Equipment connected to outdoor cameras must be permanently grounded in accordance with national and local codes. Statement 374 WARNING Hazardous voltages may be present in the outdoor camera cables under fault conditions. Disconnect all cables from the outdoor cameras before servicing this equipment. Statement 376 WARNING Do not use this product near water; for example, near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement, or near a swimming pool. Statement 1035 WARNING Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations. Statement 1036 WARNING Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface. Statement 1037 WARNING Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning. Statement 1038 Camera Accessories Installation and Administration Guide 39

40 Installing the Cisco PVC300 in a Cisco VC 030 Enclosure STEP 1 Feed the power cord and Ethernet cable through the enclosure cover, appropriate bracket or adapter as needed for your situation. STEP Insert and connect the power cord and Ethernet cable to the appropriate sockets. STEP 3 Using the two screws provided, secure the Cisco PVC300 network camera to the cross iron plate. Camera Accessories Installation and Administration Guide 40

41 Installing the Cisco PVC300 in a Cisco VC 030 Enclosure STEP 4 STEP 5 Connect the power cord and the Ethernet cable to the camera. Secure the Cisco PVC300 network camera to the enclosure with the two provided screws. STEP 6 Attach the enclosure cover to the enclosure. You attach the two pieces by twisting the cover into the groove found in the enclosure. Camera Accessories Installation and Administration Guide 41

42 Installing the Cisco PVC300 in a Cisco VC 030 Enclosure! CAUTION Repeated installations can make the cover difficult to attach to the enclosure. However, do not add lubrication to the groove in the enclosure. Adding lubrication could cause the seal to fail. Lubrication may allow water to enter the enclosure and harm the camera, or the cover to loosen over time and fall. STEP 7 Attach the enclosure to the appropriate bracket. The various brackets are shown in the illustration. STEP 8 Secure the enclosure to the selected bracket using the supplied L-type hex wrench. Camera Accessories Installation and Administration Guide 4

43 Installing the Cisco PVC300 in a Cisco VC 030 Enclosure Securing the Power Adaptor A basic installation may leave the external power adaptor exposed to the elements. It is recommended that you use either an extension cord so the power adaptor can be placed indoors, or an electrical junction box. DC Extension Cord The specification of the extension cord, if needed, are as follows: Custom length, -core copper conductor, type SPT-1 (UL/CSA style), 18 AWG, texture x 0.84 mm², withstand 105 C, and 300V Electrical Junction Box The suggested requirements of the electrical junction box, if needed, are as follows: Protection level IP66 or above; inner size at least W151 mm x L118 mm x H38 mm; material should be aluminium alloy NOTE Plastic pipe or conduit should be used to waterproof and protect the cables and cords. Where to Go Next To mount your Cisco PVC300 camera to a corner or pole, use one of the following procedures: Installing the Cisco VC 03 Corner Mount Adapter Installing the Cisco VC 033 Pole Mount Adapter Camera Accessories Installation and Administration Guide 43

44 Installing the Cisco VC 03 Corner Mount Adapter Installing the Cisco VC 03 Corner Mount Adapter Follow the instructions below to build the VC 03 adaptor that allows you to corner mount the Cisco PVC300 camera. STEP 1 Organize the following components of the Cisco VC 03 Corner Mount Adapter: Included Parts Two steel plates Waterproof corrugated tubing fitting Screw set for dome type housing Screw set to lock steel plate Silicone stoppers Required Tools (Not Included) Phillips-head screwdriver Camera Accessories Installation and Administration Guide 44

45 Installing the Cisco VC 03 Corner Mount Adapter STEP Integrate two pieces of steel plate together and securely lock using the provided screws. STEP 3 Attach the waterproof corrugated tubing fitting into the steel plate. STEP 4 Securely lock the wall mount bracket with the corner mount adapter by using the provided screws. STEP 5 Feed the cables through the brackets and waterproof corrugated tubing fitting. Camera Accessories Installation and Administration Guide 45

46 Installing the Cisco VC 03 Corner Mount Adapter STEP 6 STEP 7 Build the camera enclosure as described in Steps 3-8 in Installing the Cisco PVC300 in a Cisco VC 030 Enclosure, page 37. Use the silicone stoppers to plug the unused holes on the steel plate. STEP 8 Screw the enclosure unit to the corner mount adapter. STEP 9 Screw the enclosure unit and bracket to wall. STEP 10 (Optional) Plastic pipe or conduit should be used to waterproof and protect the cables and cords. Camera Accessories Installation and Administration Guide 46

47 Installing the Cisco VC 033 Pole Mount Adapter Installing the Cisco VC 033 Pole Mount Adapter Follow the instructions below to build the Cisco VC 033 adaptor that allows you to pole mount the Cisco PVC300 camera. STEP 1 Organize the following components of the Cisco VC 03 Pole Mount Adapter: Included Parts Steel plate Three stainless steel belts Waterproof corrugated tubing fitting Screw set Silicone stoppers Required Tools (Not Included) Phillips-head screwdriver Camera Accessories Installation and Administration Guide 47

48 Installing the Cisco VC 033 Pole Mount Adapter STEP Attach the waterproof corrugated tubing fitting into the steel plate. STEP 3 Securely lock the wall mount bracket with the pole mount adapter by using the provided screws. STEP 4 Feed the stainless belt through the holes of the VC 033. STEP 5 Feed the cables through the brackets and waterproof corrugated tubing fitting. Camera Accessories Installation and Administration Guide 48

49 Installing the Cisco VC 033 Pole Mount Adapter STEP 6 STEP 7 Build the camera enclosure as described in Steps 3-8 in Installing the Cisco PVC300 in a Cisco VC 030 Enclosure, page 37. Fasten the enclosure unit to the pole mount adapter. STEP 8 STEP 9 Attach the housing unit to the pole and securely lock the stainless belt to the pole. (Optional) Plastic pipe or conduit should be used to waterproof and protect the cables and cords. Camera Accessories Installation and Administration Guide 49

50 Installing the VC0 Cameras in a VC 05 Enclosure Installing the VC0 Cameras in a VC 05 Enclosure Follow the instructions below to install a Cisco VC0 network camera into a Cisco VC 05 enclosure. Before You Begin Organize the components of the VC 05 enclosure unit. Included Parts Enclosure cover and base TORX tamper-resistant screwdriver Two screws to secure camera to base Alignment Template Required Tools and Parts (Not Included) # Phillips screwdriver Construction and electrical items needed for installation, as required Preparing the Enclosure WARNING Equipment connected to outdoor cameras must be permanently grounded in accordance with national and local codes. Statement 374 WARNING Hazardous voltages may be present in the outdoor camera cables under fault conditions. Disconnect all cables from the outdoor cameras before servicing this equipment. Statement 376 Camera Accessories Installation and Administration Guide 50

51 Installing the VC0 Cameras in a VC 05 Enclosure WARNING Do not use this product near water; for example, near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement, or near a swimming pool. Statement 1035 WARNING Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations. Statement 1036 WARNING Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface. Statement 1037 WARNING Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning. Statement 1038 Camera Accessories Installation and Administration Guide 51

52 Installing the VC0 Cameras in a VC 05 Enclosure STEP 1 If a dome cover is attached to the camera, remove the two screws with the provided TORX screwdriver, and then detach the dome cover. STEP Use the provided TORX screwdriver to loosen the four screws that attach the enclosure cover to the base and lift the enclosure cover off the base STEP 3 TIP Place the camera into the base, aligning the bottom of the camera with the raised base of the enclosure. Temporarily place the enclosure cover back on to make sure the Status LED comes through the opening in the enclosure. Camera Accessories Installation and Administration Guide 5

53 Accessory Installation Processes Installing the VC0 Cameras in a VC 05 Enclosure STEP 4 Attach the camera to the base using the enclosed screws with a # Phillips screwdriver (not included) as you line up the LED with the LED cutout in the cover. Installing the Enclosure STEP 1 Place the provided template on the ceiling or wall where the camera and enclosure are to be mounted STEP Complete any cutting and wiring as required. Camera Accessories Installation and Administration Guide 53

54 Installing the VC0 Cameras in a VC 05 Enclosure STEP 3 Place camera and enclosure base into prepared opening and make all required connections Camera Accessories Installation and Administration Guide 54

55 Installing the VC0 Cameras in a VC 05 Enclosure STEP 4 Tighten the anchor screws found on the enclosure base with a Phillips screwdriver until the anchors securely hold the unit into the wall or ceiling Camera Accessories Installation and Administration Guide 55

56 Installing the VC0 Cameras in a VC 05 Enclosure STEP 5 Make any final focus or zoom adjustments to your camera. Refer to the VC0 Administration Guide for setup instructions. STEP 6 Reattach the enclosure cover to the base using the TORX screwdriver Camera Accessories Installation and Administration Guide 56

57 A Specifications Cisco CAMLWA (Computar 1/3-inch.3 mm Wide Angle Lens) Device Dimensions Power Certification Operating Temp Storage Temp Operating Humidity Storage Humidity 1.59 inch x 1.6 inch (3 mm x 41. mm) n/a RoHS -10ºC to 50ºC (º-4F to 140ºF) -0ºC to 60ºC (º-4F to 140ºF) 80% relative humidity, Non-Condensing 90% relative humidity, Non-Condensing Camera Accessories Installation and Administration Guide 57

58 Specifications Cisco CAMLMI (Tamron 1/3-inch 3-8 mm Varifocal.7X Zoom Lens) A Cisco CAMLMI (Tamron 1/3-inch 3-8 mm Varifocal.7X Zoom Lens) Device Dimensions Power Certification Operating Temp Storage Temp Operating Humidity Storage Humidity 1.59 inch x 1.6 inch (3 mm x 41. mm) n/a CE -0ºC to 60ºC (º-4F to 140ºF) -0ºC to 60ºC (º-4F to 140ºF) 80% relative humidity, Non-Condensing 80% relative humidity, Non-Condensing Cisco VC 00 (Camera Exterior Enclosure with Heater and Blower for the Cisco PVC300/WVC300) Unit Weight Power Certification Operating Temp Storage Temp Operating Humidity Storage Humidity 1.68 lb or 6.81 oz (.76 kg) N/A CE, IP55, FCC, LVD, RoHS -0ºC to 50ºC (º-4F to 1ºF) -30ºC to 60ºC (º-F to 140ºF) 0% to 90% relative humidity, Non-Condensing 0% to 95% relative humidity, Non-Condensing Camera Accessories Installation and Administration Guide 58

59 Specifications Cisco VC 00 (Camera Exterior Enclosure with Heater and Blower for the Cisco PVC300/WVC300) A Device Dimensions 5.31 inch x 5.51 inch x 17. inch (135 mm x 140 mm x 450 mm) The inner dimensions of the camera mount: 415mm 135mm 6mm 55mm mm /4ʺ Screw The dimensions of the bracket base: mm 83.00mm 95.00mm 8.00mm Camera Accessories Installation and Administration Guide 59

60 Specifications Cisco VC 030 (Camera Enclosure Exterior Pan Tilt for the Cisco PVC300) A Cisco VC 030 (Camera Enclosure Exterior Pan Tilt for the Cisco PVC300) Device Dimensions Camera Accessories Installation and Administration Guide 60

61 Specifications Cisco VC 030 (Camera Enclosure Exterior Pan Tilt for the Cisco PVC300) A Unit Weight plus Bracket as shown in picture lb (3.9 kg) Power Adapter 1VDC /3A Certification Operating Temp Storage Temp Operating Humidity Storage Humidity CE, FCC, C-Tick, ICES, LVD, RoHS, IP66-0ºC to 50ºC (º-4F to 1ºF) -0ºC to 50ºC (º-4F to 1ºF) 0% to 95% relative humidity, Non-Condensing 0% to 95% relative humidity, Non-Condensing Camera Accessories Installation and Administration Guide 61

62 Specifications Cisco VC 05 (Indoor Recessed Ceiling Mount Kit for the Cisco VC0) A Cisco VC 05 (Indoor Recessed Ceiling Mount Kit for the Cisco VC0) Device Description Unit Weight A metal mount with plastic enclosure and clear dome cover lb or 8.33 oz (.803 kg) Camera Accessories Installation and Administration Guide 6

63 Specifications Cisco VC 05 (Indoor Recessed Ceiling Mount Kit for the Cisco VC0) A Device Dimensions 7.09 inch x 4.7 inch (180mm x 10mm) D x H Lens Color Power Transparent lens for unaltered video images N/A Camera Accessories Installation and Administration Guide 63

64 B Where to Go From Here Cisco provides a wide range of resources to help you and your customer. Support Cisco Small Business Support Community Cisco Small Business Support and Resources Phone Support Contacts Cisco Small Business Firmware Downloads Product Documentation Cisco Small Business Camera Documentation Cisco Small Business Cisco Partner Central for Small Business (Partner Login Required) Cisco Small Business Home small_business _support_center_contacts.html Select a link to download firmware for Cisco Small Business Products. No login is required. Downloads for all other Cisco Small Business products, including Network Storage Systems, are available in the Download area on Cisco.com at (registration/login required) Camera Accessories Installation and Administration Guide 64