SPECIFICATION INDEX. CUSTOMER/MILITARY SPECIFICATIONS PCA WEBSITE (Revised on 11/10//2015)

Transcription

1 AGUSTA NTA010R Rev. G Drawing Procedures Gen. Requirements NTA013R Rev. C Drawing Requirements Geometric Tolerances NTA022R Rev. C Surface Texture and Condition NTA023R Rev. B Marking of Parts ALENIA ADET 0031 Rev. B Finishing of Aluminum Alloy Parts by deburring, breaking of sharp edges or radiusing ADET 0196 Rev. C Forming & Rectification of Aluminum Alloys By Rolling ADET 0237 Rev. C Forming & Rectification of Metallic Materials Bt 3 Points Bending BOEING CO. BAC1505 Rev. BC Tee 90 Degree, Aluminum, Extruded BAC1506 Rev. BK Tee, Miscellaneous, Aluminum, Extruded BAC1520 Rev. AM Miscellaneous Aluminum, Extruded BAC5000 Rev. AN Sealing, General BAC5018 Rev. L Installation of Safetying Devices BAC5019 Rev. U Chromic Acid Anodizing BAC5034 Rev. N Temporary Protection of Production Materials, Parts & Assemblies w/ Non adherent Film BAC Rev. G Temporary Protection of Production Materials, Parts, & Assemblies with Coatings BAC Rev. D Temporary Protection of Production Materials, Parts & Assemblies w/ Non adherent Film BAC Rev. D Temporary Protection of Production Materials, Parts & Assemblies With Preservatives BAC Rev. G Temporary Protection of Production Materals, Parts & Assemblies w/ Pressure Sensitive Tape BAC Rev. C Solid Rivet Instl In Composite Structures BAC5300 Rev. M Fitting of Metal Parts BAC Rev. H Surface & Edge Integrity of Metal Parts BAC Rev. H Metal Part Forming, Straightening & Fitting BAC5307 Rev. U Part Marking BAC5308 Rev. G Application of Stencil & insignia Markings BAC5325 Rev. J Application of Non Chromated Primer on Composite, Plastic, Titanium & Cres Surfaces BAC5338 Rev. E Acid Etch And Electrochemical Etch Marking BAC5401 Rev. E Storage, Handling, Issuance & Age Control of Rubber or Rubber-Like Materials BAC5423 Rev. W Penetrant Inspection BAC5424 Rev. U Magnetic Particle Inspection BAC5439 Rev. J Ultrasonic Inspection BAC5514 Rev. AP Common Bonding Requirements for Structural Adhesives BAC5555 Rev. T Phosphoric Acid Anodizing of Aluminum for Structural Bonding BAC5602 Rev. AF Heat Treatment of Aluminum Alloys BAC5619 Rev. H Heat Treatment of Corrosion Resistant Steel BAC5621 Rev. K Temperature Control for Processing Of Metals BAC5625 Rev. E Surface Treatments for Ferrous Alloys BAC5626 Rev. C Colored Chemical Conversion Coatings For Aluminum BAC5632 Rev. D Boric Acid Sulfuric Acid Anodizing BAC5650 Rev. E Hardness Testing BAC5651 Rev. D Eddy Current Electrical Conductivity Inspection BAC5663 Rev. C Sol-Gel Conversion Coatings For Aluminum Alloys BAC5665 Rev. A Application of Sol-Gel Conversion Coatings on Corrosion Resistant Alloys BAC5709 Rev. W Hard Chromium Plating BAC5710 Rev. V Application of Special Purpose Coatings

2 BAC5719 Rev. AA Chemical Conversion Coatings For Aluminum & Aluminum Alloys BAC5725 Rev. G Stripping Organic Materials BAC5730 Rev. R Shot Peening BAC Rev. D Shot Peen Forming BAC Rev. C Shot Peening Self Contained BAC5736 Rev. W Application of Chemical/Solvent Resistant Finishes BAC5744 Rev. G Manual Cleaning (Cold Alkaline, Solvent Emulsion & Foam Cleaners) BAC5748 Rev. U Abrasive Cleaning, Deburring, And Finishing BAC5749 Rev. W Alkaline Cleaning BAC5750 Rev. N Solvent Cleaning BAC5755 Rev. AB Application of Interior Decorative Finishes BAC5765 Rev. W Cleaning & Deoxidizing Aluminum Alloys BAC5771 Rev. J Stripping Inorganic Finishes BAC5786 Rev. M Etch Cleaning of Aluminum Alloys BAC5845 Rev. R Application of Polyurethane Topcoat BAC5882 Rev. K Application of Urethane Compatible Primer BAC5946 Rev. AA Temper Inspection of Aluminum Alloys BACD2097 Rev. Y Surface Texture (U.S. Customary and Texture) BMS5-89 Rev. T Corrosion Inhibiting Adhesive Primer BMS7-186 Rev. M Aluminum Alloy Forgings BMS Rev. L Aluminum Alloy Plate, 2324 BMS7-306 Rev. K High Strenght, Corrosion Resistant Aluminum Alloy Extrusions, 7150-T7751X BMS7-323 Rev. E High Strength Fatigue Tolerant, Stress Corrosion Resistant 7050 Aluminum Alloy BMS10-11 Rev. AC Chemical and Solvent Resistant Finish BMS10-83 Rev. N Interior Decorative Urethane Paint System BMS10-86 Rev. P Fluoropolymer Filled Coating BSS7015 Rev. (Org) Dimensional Control of Castings and Forgings BSS7025 Rev. (Org) Establishing & Maintaining Process Control Documents for Metallic Materials BSS7039 Rev. C Liquid Penetrant Inspection BSS7225 Rev. H Adhesion, Tape Test BSS7350 Rev. E Rockwell Hardness Testing Procedures BSS7351 Rev. E Eddy Current Electrical Conductivity-Direct Reading Method BSS7651 Rev. B Direct Reading Conductivity Inspection, Personnel Certification For D Rev. J Quality Assurance Standard for Digital Product Definition At Boeing Suppliers D Rev. AA Hardware & Software Compatibility Requirements for Suppliers Use of BCAG Catia Native Datasets as Authority for Design, Manufacturing & Inspection DOUGLAS DPS Rev. J Hardness Testing Procedures DPS Rev. AV Hardness Values for Aluminum Alloys DPS Rev. J Eddy Current Conductivity Testing-Equipment & Procedures DPS1.700 Rev. W Pyrometry DPS2.50 Rev. BG Sealing Materials and Methods DPS Rev. R Identification of Parts & Assemblies C-17 DPS Rev. U Marking Methods and Materials, Ink Stamping DPS3.69 Rev. E Forming Aluminum General DPS Rev. AP Forming of 7000 Series Aluminum Alloys DPS Rev. V Forming of 2000 Series Aluminum Alloys & DMS 2249 DPS Rev. K Forming 2024 Aluminum Alloys (Superceded by DPS ) DPS Rev. C Bar Coding

3 DPS3.381 Rev. AU Sealing Compounds, Two-Part DPS Rev. AR Epoxy (FR) Coating System DPS Rev. AB Epoxy Primer, DMS 2104 DPS Rev. N Protective Systems Peelable DPS Rev. H Alkaline Removable Temporary Protective Coating DPS4.512 Rev. E Stress Relief Forming 7000 Series Alloys DPS4.710 Rev. M Minimum Fabrication Practices For Metals DPS Rev. K Edge Condition Requirements DPS Rev. C Sheet Metal Fabrication Practices DPS Rev. AK General Fabrication Practices Commercial DPS Rev. AV Steel Heat Treatment Quench & Temper Hardenable DPS7.00 Rev. J Aluminum Heat Treatment General DPS Rev. BL Aluminum Heat Treatment Wrought Materials DPS Rev. N Aluminum Heat Treatment Procedures C17 DPS Rev. L Aluminum Heat Treatment Pyrometry (Replaced by DPS 1.700) DPS Rev. H Aluminum Heat Treatment Testing DPS9.05 Rev. L Cleaning of Carbon Steels & Low Alloy Steels DPS9.07 Rev. AN Surface Treatment of Corrosion Resistant Steels DPS9.45 Rev. AW Conversion Coatings for Aluminum DPS9.74 Rev, AD Cadmium Plating DPS9.316 Rev. AJ Stripping of Organic Coatings DPS11.01 Rev. AR Chromic Acid Anodizing Aluminum-Chromate Sealed MAA Rev. D Quality Assurance Standard for Digital Product Definition at Spirit Aerosystems. Inc. Suppliers PS12010 Rev. U Cleaning Solvent Hand or Immersion PS Rev. AC Pickling Aluminum Aloys PS13143 Rev. W Aluminum, Ion Vapor Deposition (IVD) of PS13201 Rev. AL Anodizing Aluminum Alloys PS13202 Rev. R Coating - Colorless Chemical Surface Treatment PS13204 Rev. AM Conversion Coating, Brush And Spray PS13209 Rev. W Coating, Multicolored Chemical Conversion of Aluminum Alloys (Immersion Process) PS13375 Rev. AE Application of Epoxy Primer PS13517 Rev. AA Painting of Douglas Commercial, C-17, T-38 & T-45 Aircraft PS13525 Rev. AE Polyurethane Corrosion Resistant Coating, Spray Application of PS13553 Rev. AG Impact Resistant Coating System PS13630 Rev. AF Painting of F/A-18 & AV-8 Aircraft PS13646 Rev. AL Painting of F-15 Aircraft PS14007 Rev. AB Forming Aluminum Alloy Wrought Products PS15500 Rev. Y Heat Treating Criteria for Aluminum Alloys PS Rev. A Heat Treating of Aluminum Alloys to the T6/T62 & T72 Conditions PS Rev. D Heat Treating of Aluminum Alloys to the T76 And T5 Conditions PS15701 Rev. P General Heat Treat Criteria for Aluminum Alloys PS15719 Rev. G Hardening 7050 Extrusions to the T76 Temper PS16001 Rev. CC Marking of Fabricated Parts PS16010 Rev. R Identification of parts and Assemblies PS16011 Rev. V Marking Methods and Materials PS20001 Rev. AB Protection of Parts During Fabrication and Storage PS20006 Rev. R Sheet Metal & Extrusions, Rqrmts & Acceptance Criteria for Parts Fabricated From PS20022 Rev. P Chemical Milling PS20024 Rev. P Deburring, Blending, and Sanding of Metal Parts

4 PS21201 Rev AF Magnetic Particle Inspection PS21202 Rev. AT Penetrant Inspection PS21203 Rev. K Hardness Testing of Parts & Materials PS21207 Rev. G Eddy Current Determination of Electrical Conductivity For Aluminum Alloys PS21212 Rev. F Hardness Inspection of Metals PS21313 Rev. M Coating Adhesion Test PS22162 Rev V Automatic Gas Tungsten (GTAW) of Turbular Joints PS23023 Rev. W(Supp 8) Hardness & Electrical Conductivity Inspection Criteria for Metals PS23041 Rev. V Machined Parts, Requirements & Acceptance Criteria for BELL HELI BPS 4001 Rev. O Chromic Acid Anodizing BPS 4050 Rev. Y Marking Aircraft Parts BPS 4089 Rev. M Fluorescent Penetrant Inspection BPS 4451 Rev. G Application of Epoxy Primer BPS 4555 Rev. NC Thin Film Sulfuric Acid Anodize EMBRAER MEP Rev. O Aluminum Alloy 7475, Bare & Clad Sheet MEP Rev F Aluminum Alloy Alclad 2024, Fine Grained-Sheet MEP Rev H Aluminum Alloy 2524, Alclad Sheet & Bare Plate MEP Rev Q Epoxy Primer, Chromate Based, Fluid Resistant MEP Rev AS High Solids Polyurethane Enamel, Fluid Resistant NE Rev. L Inks for Marking of Parts NE Rev AE Parts-Marking Methods NE Rev O Metallic Parts- Cutting, Chamfering & Deburring NE Rev J Machined Metallic Details-General Tolerances NE Rev A Dimensioning & Tolerancing NE Rev I Aluminum Parts Forming & Straightening NE Rev I Metal Sheet or Extruded Parts General Tolerances NE Rev X Aluminum Alloys Hardness & Conductivity Values NE Rev K Joggles in Extruded & Performed Sheet Sections NE Rev D Aluminum & Its Alloys-Annealing NE Rev W Aluminum & Its Alloys-Solution Heat Treatment NE Rev P Aluminum & Its Alloys-Artificial Aging NE Rev P Aluminum & Its Alloys-Chemical Conversion Coating NE Rev AB Aluminum & Its Alloys-Anodic Coatings In Chromic Acid NE Rev AL Epoxy Primer, Chromate Based, Fluid Resistant (MEP Types I, II & III) For Metallic Detail Parts-Application Requirements NE Rev AY High Solids Polyurethane & Metallic (MICA) Enamel(MEP )-Application Requirements NE Rev U Aluminum & Its Alloys-Chemical Milling NE Rev H Raw Materials/Euipment/Parts Protection For Handling, Transportation & Storage PF Rev M Surfaces For Electrical Bonding-Preparation & Protecton ERICKSON EPFS-307 Rev. Y Engineering Product Fabrication EPFS -309 Rev. D Chemical Milling EPFS -319 Rev. F Forming and Straightening of Aluminum Alloys

5 ES0037 Rev. H Identification Marking of Parts ES0051 Rev. A Process Specification for Adhesive Bonding Main and Trail Rotor Blades ES0053 Rev. B Adhesive Bonding System, Main and Tail Rotor Blades GOODRICH RPS Rev. F Controlled Processes & Materials RPS Rev. AJ Nut Substitutions For Hi-Lock Collar RPS Rev. U Chromic Acid Anodize RPS Rev. T Sulfuric Acid Anodize For Aluminum Alloys RPS Rev. AE Application of Organic Finishes & Dissimilar Metal Protection RPS Rev. AD Part Marking & Identification RPS Rev. AE Sealing RPS Rev. AE Surface Preparation of Heat & Corrosion Resistant Alloys RPS Rev. H Cleaning of Aluminum RPS Rev. L Shop Fabrication Standards RPS Rev. C Inspection of Castings & Forgings RPS Rev. F Penetrant Inspection RPS Rev. A Penetrant Inspection of Grid-Lock Parts RPS Rev. L Bearing Installation And Retention ISRAEL AIR PS E Rev. K Cleaning Of Aluminum Alloys PS E Rev. S Chromic Acid Anodize PS E Rev. (Orig.) Application of Epoxy Top Coat PS E Rev. F Application of Fluid Resistant Epoxy Primer PS E Rev. F2 Identification of Aircraft Parts PS E Rev. B Fabrication Practices of Metallic Parts General PS Rev. B Fabrication Practice Surface Finishing and Roughness Control PS E Rev. E1 Hardness Testing of Metals PS E Rev. D2 Hardness & Electrical Conductivity Inspection Acceptance Criteria Tables for Metal Parts PS E Rev. D Eddy Current Determination of Electrical Conductivity of Aluminum Parts PS E Rev. G Liquid Penetrant Inspection PS E Rev. E Incoming Raw Material Acceptance Testing (Laboratory Test) LOCKHEED MARTIN DS Rev. AA Hardness Values & Hardness-Tensile Strength Relationship for Metals FMS-3027 Rev. C F-16 Corrosion Resistant Epoxy Primer Coatings FPS-1003 Rev. M Sealing Specification Pressurized & Non-Fuel Areas (V1) FPS-1051 Rev. C Chemical Milling of Metals (Amend. 1) FPS-3001 Rev. G Contractors Finish Specifications for F-16 Air Combat Fighter FPS-3008 Rev. F Marking of Aircraft & Aerospace Ground Equipment Parts FPS-3017 Rev. F Metal Removal Procedures & Limitations FPS-3018 Rev. B Forming of Aluminum Alloys FPS-3033 Rev. B Chromic Acid Anodize Treatment for Aluminum Alloys FPS-3035 Rev. P Adhesive Sealed Integral Fuel Tank Applications FPS-3090 Rev. B Thin Film Sulfuric Acid Anodize Treatment for Aluminum & Aluminum Alloys M039 Rev. L Chem Milling, AL, TI or Cres Aly, RGH/Radius Tol For NDTS-1101 Rev. H Penetrant Inspection (Amend. 2, 3) NDTS-1500 Rev. K Hardness and Conductivity Testing (Amend. 1)

6 NDTS-1501 Rev. K Hardness Testing (Amend. 1) NDTS-1502 Rev. M Conductivity Testing G14 Rev. G30 Aircraft Finishes, Coding Scheme G112M Rev. G14 Electrical Bonding G700 Rev. G19 Epoxy/Primer/Polyurethane Topcoat PM-5010 Rev. L Supplier/Seller Shipping Instructions PS0170 Rev. G11 (V15) Cleaning of Parts and Materials (also use for stripping) PS0471 Rev. G39 Finish Specification for C-130 Series Airplane PS0491 Rev. G8 Cadmium Plating (Electrodeposited) PS0581 Rev. G37 Fasteners, Mechanical, Preparation for and Installation of PS1005 Rev. G8 Protection of Materials & Parts In Process Of Fabrication or Assembly STP Rev. A Processing of Titanium & Titanium Alloys STP Rev. AC Forming & Fabrication Practices for Sheet Metal, Extrusions, Forgings, & Billets (V19, V20, V21, V22, V23) STP Rev. K Fabrication of Titanium & Titanium Alloy Parts (V1, V3) STP Rev. E Standard Machining Practices, Tolerances & Allowances (V2) STP Rev. H Chemical Milling of Aluminum Alloys STP Rev. L (V6) Shot Peening of Metal Parts STP Rev. G Magnetic Particle Inspection, Requirements for STP Rev. N (V4) Penetrant Inspection, General Requirements for STP Rev. N Heat Treatment of Carbon & Low Steels to Below 220KSI STP Rev. M Stress Relieving, Baking & Cold Treatment of Steel Parts STP Rev. T (V11) Heat Treatment of Precipitation hardening stainless steel STP Rev. N Heat Treatment of Carbon & Low Alloy Steels to below 220 ksi uts STP Rev. AA Heat Treatment of Aluminum Alloys for Use on Aircraft (V24 V31) STP Rev. J (V2) Heat Treatment of Titanium & Titanium Alloys STP Rev. B Application of Scale Inhibiting Compound STP Rev. G Welding, Resistance-Spot Intermittent Spot, & Seam (1) (V1) (V5) STP Rev. R Wet Installation of Fasteners (V1) STP Rev. H Cleaning of Carbon & Low Alloy Steels STP Rev. W Cleaning Of Aluminum & Aluminum Alloys (V11, V12, V13) STP Rev. H Cleaning of Titanium & Titanium Alloys STP Rev. AC Sulfuric Acid Anodizing of Aluminum & Aluminum Alloys (V17) (V18) STP Rev. M Chromic Acid Anodize (V1 V11 V20 V21) STP Rev. L Chemical Protective Film for Aluminum and Aluminum Alloys (V6 V7) (V8) STP Rev. M Application of Chemical Film Protective Treatments to Aluminum & Aluminum Alloys By methods other than Immeersion STP Rev. D Stripping of Organic Finishes STP Rev. B Application & Removal, Temp. Protective Coatings STP Rev. T (V1) Marking Parts & Assemblies for ID & Inspection TMS-MC-015 Rev. 29 Supplier Tooling Manual (Tool Mfgt. Specs Material Control -015) MILITARY AND FEDERAL SPECIFICATIONS / STD s A-A /20/98 Synthetic Lacquer, Camouflage, Exterior, VOC Complaint (TT-L-20A was superseded by A-A-3164 MIL-STD-1537 Rev. C Test Methods for Electrical Conductivity Test for Verification of Heat Treatment of Aluminum Alloys Eddy Current Method FED-STD-595 Rev. C Colors used in Government Procurement MIL-A-8625 Rev. F (1) Anodic Coatings for Aluminum and Aluminum Alloys

7 MIL-DTL-5541 Rev. F Chemical Conversion Coatings on Aluminum & Aluminum Alloys MIL-F Rev. D (2), N 1 Finishes, Organic, Weapons System, Application and Control MIL-PRF Rev. G (1) Coating, Epoxy, High Solids MIL-PRF Rev. K Primer Coatings-Epoxy, High Solids MIL-PRF Rev. E Performance Specs - Coating: Polyurethane, Aircraft & Support Equipment MIL-PRF Rev. E Primer Coatings-Epoxy, Waterborne MIL-DTL-5002 Rev. E Surface Treatment and Organic Coating for Metal Surface of Weapons systems NORTHROP GF13D Rev. H Flushness-Fastener Counter Sink Head GH11AL Rev. H Hole Preparation - Fastener GP17G Rev. T Etch Clean GP20A Rev. CK Process And Finish Codes GS31AB Rev. AR Shop Practice Mandatory and Optional (AR2) (AR3) Amend AN1, Amend AN11 GSS4306 Rev. D Integral Fuel Tank Coating (MIL-C-27725) GSS4310 Rev K (1) Primer Epoxy Polyamide Finish Amendment 1 GSS4407 Rev. G Lacquer: Acrylic, MIL-L (GP110H) GSS4510 Rev. H Coating, Polyurethane GSS4710 Rev. F (1) (2) Identification Marking of Fabricated Metallic Parts and Assemblies GSS5100 Rev. H (1) Heat Treatment of Low Alloy Steels GSS5300 Rev. F Forming and Straightening of Aluminum Alloys Amendment 3 GSS7012 Rev. C Preparation of Surfaces by Abrasive Methods GSS7030 Rev. G Alkaline Cleaning of Ferrous and Non Ferrous Alloys GSS8056 Rev. B Cadmium Coating, Vacuum Deposited Amendment 2 GSS15302 Rev. E (3) Installation of Solid and Tubular Rivet (Release Date 11/17/94, Amend 2) GSS15303 Rev. F (2) Installation of Blind Rivets GSS26100 Rev. G Chemical Milling (Caustic Process) of Aluminum Alloy GT23A Rev. T Penetrant Inspect QOS-0021 Rev. E Conductivity and Hardness QOS-0033 Rev. H Inspection Guidelines for Sheet Metal Detail Parts & Assemblies QOS-0034 Rev. L Supplier Inspection of Tooling GLOBAL HAWK SPECS Rev. M Finish Specification Rev. D Critical Part Control Specification EPFS-307 Rev. Y Standard and Tolerances for Manufacturing Parts and Assemblies EPFS-309 Rev. D Chemical Milling EPFS-319 Rev. E Forming & Straightening of Aluminum Alloys EPFS-600 Rev. M Identification Marking, Methods of EPFS-602 Rev. M Rubber Stamp Method Identification Marking F Rev. F Non destructive Test Specification (Determination of Alum. Alloy Conductivity F Rev. G Non destructive Test Specification (Florescent Penetrant Inspection) F Rev. B Non destructive Test Specification (Hardness Testing of Metals) SAE/AMS/ASTM SPECIFICATIONS

8 AMS 2658 Rev. C Hardness and Conductivity Inspection of Wrought Aluminum Alloy Parts AMS 2700 Rev. E Passivation of Corrosion Resistant Steels AMS 2750 Rev. E Pyrometry AMS 2770 Rev. N Heat Treatment of Wrought Aluminum Alloy Parts AMS 2771 Rev. E Heat Treatment of Aluminum Alloy Castings AMS 2772 Rev. F Heat Treatment of Aluminum Alloy Raw Materials AMS-C Rev. C Coating, Corrosion Preventative Polyurethane for Aircraft Integral Fuel Tanks for Use to 250 Degrees Fahrenheit (121 Degrees Celsius) AMS-H-6088 Rev. C Heat Treatment of Aluminum Alloys (Obsolete, Superceded by AMS 2770, AMS 2771, AMS 2772 ASTM E18 Rev Standard Test Methods for Rockwell Hardness of Metallic Materials 1, 2 ASTM E 1316 Rev Standard Terminology for Nondestructive Examinations ASTM E1417 Rev Standard Practice For Liquid Penetrant Testing ISO Rev. 2003(E) Quality Mgmt Systems Guidelines For Configuration Mgmt (ED2) ISO Rev. 2003(E) Measurement Mgmt Systems-Rqrmts For Measurement Processes & Measuring Equipment (ED1) ISO/IEC Rev. 2005(E) General Rqrmts For the Competence of Testing & Calibration Laboratories MATERIAL SPECIFICATIONS AMS 2301 Rev. K Steel Cleanliness, aircraft quality magnetic particle inspection proc. AMS 4048 Rev. N Aluminum Alloy Sheet & Plate, Alclad 5.6Zn-2.5Mg-1.6Cu-0.23Cr(Alclad ) Annealed or when specified, As Fabricated (Alclad 7075-F) Composition similar to UNS A97075) (Supercedes AMS-QQ-A-250/13) AMS 4049 Rev. L Aluminum Alloy, Sheet & Plate, Alclad 5.6Zn-2.5Mg-1.6Cu-0.23Cr (Alclad 7075;-T6 Sheet-T651 Plate) Solution & Precipitation Heat Treated (Composition similar to UNS A97075) (Supercedes AMS-QQ-A-250/13) AMS 4050 Rev. H Aluminum Alloy, Plate 6.27 Zn-2.3 Cu-2.3 Mg-0.12Zr (7050-T7451) AMS 4077 Rev. G Aluminum Alloy Sheet and Plate, Alclad one side AMS 4096 Rev. C Aluminum Alloy Sheet and Plate AMS 4101 Rev. E Aluminum Alloy, Plate AMS 4201 Rev. E Aluminum Alloy Plate 6.22n-2.3Cu-2.2Mg-0.60Mn (2124-T851 AMS 4252 Rev. B Aluminum Alloy, Plate 6.4Zn-2.4Mg-2.2Cu-0.12Zr(7050-T7651) AMS 4260 Rev. G Aluminum Alloy, Investment Castings 7.0Si-0.32Mg(356.0-T6) AMS 4296 Rev. B Aluminum Alloy, Alclad Sheet and Plate 4.3 Cu-1.4Mg-0.60Mn (Alclad 2524-T3) AMS 4340 Rev. E Aluminum Alloy Extrusions 6.2 Zn-2.3Cu-2.2Mg 0.12Zr(7050-T76511) AMS 4347 Rev. C Aluminum Alloy Sheet 1.0Mg-0.8Si-0.8Cu-0.5Mn(6013-T4) AMS 4900 Rev. N Titanium Sheet, Strip & Plate Commercially Pure Annealed, 55.0KSi AMS 4901 Rev. S Titanium Sheet, Strip & Plate Commercially Pure Annealed(379MPa) AMS 4911 Rev. N Titanium Alloy, Sheet, Strip & Plate 6A1-4V annealed AMS 4935 Rev. K Titanium Alloy Extrusions & Flash Welded Rings 6A1-4V AMS 5122 Rev. J Steel Strip (SAE 1095) Hard Temper AMS 5510 Rev. S Steel, Corrosion & Heat Resistant, Sheet Strip and Plate 18Cr-10.5NNi-0.40Ti AMS 5516 Rev. P Steel, Corrosion Resistant, Sheet, Strip & Plate 18Cr-9 0Ni(Sae 30302) AMS 5517 Rev. L Steel, Corrosion Resistant, Sheet and Strip 18Cr-8Ni(Sae 30301) AMS 5528 Rev. H Steel, Corrosion Resistant Sheet, Strip & Plate 17Cr-7.0Ni-1.1A1 AMS 5599 Rev. G Nickel Alloy, Corrosion & Heat Resistant, Sheet, Strip & Plate AMS 5604 Rev. G Steel, Corrosion Resistant, Sheet, Strip & Plate 16.5Cr-4.0Ni-4.0Cu-0.30Cb AMS 5643 Rev. R Steel Bars, Forgings, Tubing & Rings 16Cr-4.0Ni-0.30Cb-4.0Cu AMS 5659 Rev. P Steel, Corrosion Resistant, Bars, Wires, Forgings, Rings & Extrusions 15Cr4.5Ni0.30Cb

9 AMS 5903 Rev. B Steel, Corrosion, Resistant, Sheet, Strip & Plate 18Cr-9.0Ni AMS 6348 Rev. D Steel, Bars 0.95Cr-0.20M0( c AMS 6349 Rev. C Steel, Bars 0.95 Cr-0.20M0 ( C AMS 6382 Rev. N Steel, Bars, Forgings, & Rings 0.95Cr-0.20M0( C AMS 6414 Rev. L Steel, Bars, Forgings & Tubing 0.80Cr-1.8Ni 0.25M0 AMS-A Rev. B Aluminum-Alloy Castings, High Strength AMS-QQ-A-200/11 Rev. A Aluminum Alloy 7075, Bar, Rod, Shapes, tube & Wire Extruded AMS-QQ-A-250 Rev. A Aluminum & Aluminum Alloy, Plate & Sheet Gen. Specification for AMS-QQ-A-250/3 Rev. A Aluminum Alloy Alclad 2014, Plate and Sheet AMS-QQ-A-250/4 Rev. B Aluminum Alloy 2024, Plate & Sheet AMS-QQ-A-250/5 Rev. B Aluminum Alclad 2024, Plate & Sheet AMS-QQ-A-250/8 Rev. C Aluminum Alloy 5052, Plate & Sheet AMS-QQ-A-250/11 Rev. A Aluminum Alloy 6061, Plate & Sheet (Obsolete, Cancelled-(Replaced by ASTM B 209) AMS-QQ-A-250/12 Rev. A Aluminum Alloy 7075, Plate & Sheet AMS-QQ-A-250/13 Rev. A Aluminum Alloy Alclad 7075, Plate & Sheet (Cancelled) (Superceded by AMS 4048 & AMS 4049) AMS-QQ-A-250/18 Rev. B Aluminum Alloy Alclad One side 7075, Plate & Sheet AMS-QQ-A-250/24 Rev. A Aluminum Alloy, 7075, Plate & Sheet (Improved Exfoliation Resistant) AMS-QQ-A-250/25 Rev. A Aluminum Alloy Alclad 7075, Plate and Sheet Improved Exfoliation Resistant (Replaced by AMS 4316) AMS-QQ-A-250/29 Rev. A Aluminum Alloy, 2124, Plate AMS-QQ-A-250/30 Rev. A Aluminum Alloy 2219, Plate and Sheet AMS-QQ-A-367 Rev. D Aluminum Alloy Forgings AMS-QQ-P-416 Rev. C Plating, Cadmium (Electrodeposited)