CARRIER REFRIGERATION EQUIPMENT AND PARTS

Transcription

1 EVAPORATOR COILS CONDENSING UNITS 1/2 Through 80 HP COMPLETE REFRIGERATION PACKAGES AIR DEFROST ELECTRIC DEFROST HOT GAS DEFROST Ceiling Temp Low Height Unit Coolers SW Series Literature No. C January, 2005 Flow Temp Low Velocity Unit Coolers LW Series Literature No. C January, 2005 All Temp 2 b Low Profile Unit coolers CW Series Literature No. C January, 2005 Inter Temp Medium Profile Unit Coolers Ultra Temp High Capacity Warehouse Unit Coolers Minicon - Air Cooled Cond. units 1/2 to 6 HP with Tecumseh hermetic and Carlyle semi-hermetic compressors FW Series Literature No. C January, 2005 HW Series Literature No. C January, 2005 CS Series - Air Cooled condensing units Literature No. C January, 2006 MidLine - CM-Series - Air Cooled Condensing Units 3-15 HP With Carlyle compressors. Literature No. C 310.2,September, 2006 MaxLine - CL-Series - Air Cooled Condensing Units HP With Carlyle compressors. Literature No. C 320, December, 2006 Plus parts for above mentioned units. Please contact your local Carlyle Certified Refrigeration Partner for all product, technical, sales and pricing issues. 94

2 Many of our units can be customized to meet specific job site requirements. Due to ongoing product development, product designs are subject to change without notice. ORDERING INFORMATION 1. Model Number 2. Type of defrost 3. Electrical characteristics voltage frequency and phase of motors. 4. Refrigerant type 5. Suction Temperature 6. Evaporator TD Please contact your local Carlyle Certified Refrigeration Partner for all product, technical, sales and pricing issues. 95

3 Dual Air Discharge Unit Cooler SW Series APPLICATIONS The Dual Air Discharge unit cooler is designed for use in walk-in coolers and freezers with low headroom clearance. Its extra low height allows more product to be stored on shelves. The dual air flow design provides even temperatures throughout the box. SIZES There are twenty models available, ranging in capacity from 4,800 to 25, TD. COIL The coil is constructed from seamless Copper tubes which are staggered and mechanically expanded into heavy gauge, corrugated, Aluminum fins, assuring maximum heat transfer. Optionally available with Copper or phenolic coated fins (phenolic fins are for air defrost only). HOUSING Rust free heavy gauge textured Aluminum is standard. Optionally available with white enamel coating. MOTORS / FANS Fan motors and blades can be easily accessed by lowering the hinged drain pan. Motors are life lubricated and are commonly in stock at most wholesale houses. ELECTRICAL Available in 115V, V & 460V/1. All components are factory wired to terminal strips and are UL & cul listed. DEFROST All models are available in air and electric defrost designs. Air defrost units are suitable for use in coolers down to 35 F. Electric defrost units are designed for use in rooms down to -10 F. Please contact your local Carlyle Certified Refrigeration Partner for all product, technical, sales and pricing issues. 96

4 Dual Air Discharge Unit Cooler SW Series AIR DEFROST / walk-in coolers 35 F and above MODEL NO. +25 F ST MOTOR AMPS DEFROST DEFROST AMPS 10 TD 15 TD CFM 115/1 230/1 WATTS 230/1 460/1 SWA ,500 11,250 1, SWA ,800 13,200 1, SWA ,800 14,700 1, SWA ,200 16,800 2, SWA SWA ,000 16,200 19,500 24,300 1,920 2, SWA SWA ,000 21,000 22,500 31,500 1,760 1, NOT AVAILABLE SWA ,000 34,500 2, SWA ,000 37,500 2, IN SWA ,400 9,600 1, SWA ,200 12,300 1, ELECTRIC SWA ,300 13,950 1, SWA ,000 15,000 2, DEFROST SWA ,300 18,450 2, SWA ,000 21,000 1, SWA ,700 23,500 2, SWA ,000 28,500 1, SWA ,800 31,200 2, SWA ,200 34,800 3, Standard voltage supplied on SWA models is 115/1/60 8 FPI 6 FPI ELECTRIC DEFROST / walk in coolers and freezers below +34 F MODEL NO. 10 TD MOTOR AMPS DEFROST DEFROST AMPS -20 ST +20 ST CFM 115/1 230/1 WATTS 230/1 460/1 SWE ,300 6,360 1, SWE ,200 7,440 1, SWE ,900 8,200 1, SWE ,700 9,240 2, SWE ,000 10,800 1, SWE ,000 12,000 1, SWE ,500 15,000 2, SWE ,000 16,800 1, SWE ,000 19,200 2, SWE ,800 23,200 3, SWE ,800 5,760 1, SWE ,800 6,960 1, SWE ,500 7,800 1, SWE ,200 8,640 2, SWE ,400 10,080 1, SWE ,500 11,400 1, SWE ,500 13,800 2, SWE ,800 15,360 1, SWE ,500 17,400 2, SWE ,300 20,760 3, Standard voltage supplied on SWE models is /1/60 6 FPI 4 FPI Please contact your local Carlyle Certified Refrigeration Partner for all product, technical, sales and pricing issues. 97

5 Dual Air Discharge Unit Cooler SW Series AIR DEFROST Models 8 FPI 6 FPI MODEL DIMENSIONS(in) TXV CONNECTIONS(in) SHIP WT. NUMBER L W H A B TYPE LIQ. (ODS) SUCT. (ODS) (lbs) SWA /2 28-3/ EXT 1/2 5/8 95 SWA /2 28-3/ EXT 1/2 5/8 100 SWA /2 28-3/ EXT 1/2 5/8 105 SWA /2 28-3/4 8-3/ EXT 1/2 7/8 125 SWA /2 28-3/4 8-3/ EXT 1/2 7/8 130 SWA /2 28-3/4 8-3/ EXT 1/2 7/8 135 SWA /2 28-3/4 8-3/ EXT 1/2 7/8 150 SWA /2 28-3/4 10-1/ EXT 1/2 7/8 155 SWA /2 28-3/4 10-1/ EXT 1/2 7/8 165 SWA /2 28-3/4 10-1/ EXT 1/2 1-1/8 185 SWA /2 28-3/ EXT 1/2 5/8 90 SWA /2 28-3/ EXT 1/2 5/8 95 SWA /2 28-3/ EXT 1/2 5/8 100 SWA /2 28-3/4 8-3/ EXT 1/2 7/8 120 SWA /2 28-3/4 8-3/ EXT 1/2 7/8 125 SWA /2 28-3/4 8-3/ EXT 1/2 7/8 130 SWA /2 28-3/4 8-3/ EXT 1/2 7/8 145 SWA /2 28-3/4 10-1/ EXT 1/2 7/8 150 SWA /2 28-3/4 10-1/ EXT 1/2 7/8 160 SWA /2 28-3/4 10-1/ EXT 1/2 1-1/8 180 ELECTRIC DEFROST Models 6 FPI 4 FPI MODEL DIMENSIONS(in) TXV CONNECTIONS(in) SHIP WT. NUMBER L W H A B TYPE LIQ. (ODS) SUCT. (ODS) (lbs) SWE /2 28-3/ EXT 1/2 5/8 95 SWE /2 28-3/ EXT 1/2 5/8 100 SWE /2 28-3/ EXT 1/2 5/8 105 SWE /2 28-3/4 8-3/ EXT 1/2 7/8 125 SWE /2 28-3/4 8-3/ EXT 1/2 7/8 130 SWE /2 28-3/4 8-3/ EXT 1/2 7/8 135 SWE /2 28-3/4 8-3/ EXT 1/2 7/8 150 SWE /2 28-3/4 10-1/ EXT 1/2 7/8 155 SWE /2 28-3/4 10-1/ EXT 1/2 7/8 165 SWE /2 28-3/4 10-1/ EXT 1/2 1-1/8 185 SWE /2 28-3/ EXT 1/2 5/8 90 SWE /2 28-3/ EXT 1/2 5/8 95 SWE /2 28-3/ EXT 1/2 5/8 100 SWE /2 28-3/4 8-3/ EXT 1/2 7/8 120 SWE /2 28-3/4 8-3/ EXT 1/2 7/8 125 SWE /2 28-3/4 8-3/ EXT 1/2 7/8 130 SWE /2 28-3/4 8-3/ EXT 1/2 7/8 145 SWE /2 28-3/4 10-1/ EXT 1/2 7/8 150 SWE /2 28-3/4 10-1/ EXT 1/2 7/8 160 SWE /2 28-3/4 10-1/ EXT 1/2 1-1/8 180 Please contact your local Carlyle Certified Refrigeration Partner for all product, technical, sales and pricing issues. 98

6 Low Velocity Discharge Unit Cooler LW Series APPLICATIONS The Low Velocity Discharge unit coolers are ideally suited for meat cutting, holding and packaging rooms as well as produce storage and florist boxes. SIZES There are eight models available, ranging in capacity from 6,700 to 37, TD. HOUSING Rust free heavy gauge textured Aluminum is standard. Optionally available with white enamel coating. COIL Seamless copper tubes are staggered and mechanically expanded into heavy gauge corrugated Aluminum fins assuring maximum heat transfer. Optionally available with copper or phenolic coated fins. MOTORS / FANS Fan motors and blades can be easily accessed by lowering the hinged drain pan. Motors are life lubricated and are commonly in stock at most wholesale houses. ELECTRICAL Available in 115V and 208/230V. All components are factory wired to terminal strips and are UL and cul listed DEFROST All models are available in air, electric and hot gas defrost designs. Air defrost units are suitable for use in coolers down to 35 F. Electric, Hot Gas Re-Evap and Hot Gas Reverse Cycle coils are designed for use in rooms down to 28 F. Please contact your local Carlyle Certified Refrigeration Partner for all product, technical, sales and pricing issues. 99

7 Low Velocity Discharge Unit Cooler LW Series PERFORMANCE AND ELECTRICAL DATA CAPACITY (Btu/hr) MOTOR ELECTRIC DEFROST MODEL CFM AMPS AMPS 10 F TD 15 F TD 20 F TD QTY NO 115V 230/1 WATTS 230V/1 230V/3 460V/1 LW* ,700 10,050 13, LW* ,000 15,000 20, LW* ,500 20,250 27, LW* ,000 24,000 32, LW* ,000 27,000 36, LW* ,000 33,000 44, LW* ,500 37,950 53, LW* ,000 55,500 74, ORDERING INFORMATION REQUIRED: 1. Model number 2. Type of defrost 3. Electrical characteristics 4. Refrigerant type 5. Suction temperature 6. Evaporator TD NOTE: Air defrost models are suitable for +35 F room temperature and above. Electric and Hot Gas defrost suitable for +28 F room temperature and above. PHYSICAL DATA MODEL DIMENSIONS (in) MODEL NOMENCLATURE: SHIP WT. (lbs) CONNECTIONS (in.)1 NO A B C D W LIQUID SUCTION DRAIN LW* /2 6-1/4 8-1/2 58-1/2 1/2 F.N. 7/8 OD 3/4 MPT 155 LW* /2 6-1/4 8-1/2 82-1/2 1/2 F.N. 7/8 OD 3/4 MPT 205 LW* /2 9-3/ /2 1/2 F.N. 1-1/8 OD 3/4 MPT 265 LW* /2 9-3/ /2 1/2 F.N. 1-1/8 OD 3/4 MPT 285 LW* /2 9-3/ /2 1/2 F.N. 1-1/8 OD 3/4 MPT 325 LW* /2 9-3/ /2 1/2 F.N. 1-1/8 OD 3/4 MPT 340 LW* /2 12-3/ /2 1/2 F.N. 1-1/8 OD 3/4 MPT 370 LW* /2 12-3/ /2 1/2 F.N. 1-1/8 OD 3/4 MPT All models require externally equalized TXV. Please contact your local Carlyle Certified Refrigeration Partner for all product, technical, sales and pricing issues. 100

8 Low Profile Unit Cooler CW Series AIR DEFROST - 3,900 to 39,000 BTUH ELECTRIC DEFROST - 3,600 to 28,000 BTUH HOT GAS DEFROST - 3,600 to 28,000 BTUH SMALL TO MEDIUM WALK-INS COOLERS & FREEZER APPLICATIONS FEATURES: The Carrier Low Profile is the original low profile unit cooler that has established an industry standard as being the all purpose design for walk-in coolers, freezers and other applications. They feature an air draw-through design offering air, electric and hot gas defrost models. SIZES There are 35 sizes available with 3,700 to 39,000 BTUH at a 10 TD ranging from 740 to 4,980 cfm. One through six fan models are available. HOUSING Rust-free, heavy gauge, textured Aluminum casing is light weight yet durable. Each fan section is baffled to prevent short cycling of the air. The unit is designed to mount flush to the ceiling and meets all NSF requirements. Slotted hangers are provided for easy installation. Drain fittings are installed in the horizontal position to gain more usable headroom in low ceiling applications. The end panels now are hinged to open up out for easy access to both the piping and electrical ends. Optional expansion valves can be conveniently installed inside the cabinet. COIL Seamless Copper tubes are staggered and mechanically expanded into corrugated Aluminum fins and heavy gauge tube sheets to achieve maximum heat transfer and strength. Die formed fin collars provide even fin spacing. Fin spacings available are 4, 6, and 8 fins per inch. Sweat connections are standard on all models and optional field installed flare connection kits are available at no extra charge. MOTORS All motors are 1/20 HP, permanently lubricated, ball bearing, with thermal overload protection. Available in 115V, 208/230V and optional 460V, single Phase. Optional high efficiency PSC motors are available in 115V and 230V. FANS Heavy duty 12 Aluminum fans are balanced to provide vibration-free operation. Our new low throw black plastic fan guards have an improved air pattern. The optional epoxy resin high throw fan guard moves air up to 50 feet. AIR DEFROST All models with the prefix CWA are designed for use in coolers of 35 F and warmer. Complete air defrost systems for off-cycle or timed air defrost are available from Carrier. ELECTRICAL Available in 115V, 208/230V, and 460V (see page 4). All components are factory wired to convenient screw-type terminal strips. A large compartment is supplied internal to the unit for all electrical components and is easily accessible by removing the end panel. All models are UL & cul listed. ELECTRIC DEFROST Available on all models with the prefix CWE. Designed for use where electric heat is used to defrost. Placement of the heaters internal to the coil allows for an extremely rapid and efficient defrost. This arrangement enables the heat to be conducted through the fins from the center out for an even defrost pattern. All heaters are wired to a terminal strip to allow a quick field change-over from single phase to three phase, 230V to 460V and vice versa. A lower heater is installed close to the drain pan for fast, reliable drainage. A defrost termination thermostat (DT) terminates the defrost cycle when the temperature is satisfied. A heater safety thermostat is installed to prevent heaters from overheating above 75 F in case of DT failure. All heaters are flexible and can be easily replaced within 12 inches of the end of the units. A fan delay thermostat is supplied to allow the warm coil to cool after a defrost cycle prior to the fans turning on. Complete electric defrost refrigeration systems are available from Carrier. HOT GAS DEFROST Two types available - Re-Evap models with the prefix CWH and reverse cycle with the prefix CWG. All models include a fixed DTFD factory wired and a hot gas drain pan circuit to defrost the drain pan. On all Hot Gas models, the drain fitting is located on the left-hand rear of the unit when facing the fan guards. Re-evap models include a Heat Exchanger-Re-Evaporator shipped together with the unit for field installation. Complete Re-Evap Refrigeration Systems are available from Carrier. Contact factory for piping information. Please contact your local Carlyle Certified Refrigeration Partner for all product, technical, sales and pricing issues. 101

9 AIR DEFROST / SPECIFICATIONS 8 FPI 6 FPI 4 FPI BTUH Total Fan Motor AMPS - 1 Phase Total Fan Motor AMPS 1 Phase 25 F ST CFM Standard Motor Optional PSC Motor MODEL NO 10 TD 12 TD 115V 230V 460V 115V 230V CWA ,100 4, CWA ,300 6, CWA ,600 7, CWA ,600 9,100 1, CWA ,700 11,600 1, CWA ,600 12,700 1, CWA ,200 14,600 1, CWA ,400 16,100 1, CWA ,000 19,200 2, CWA ,500 23,400 2, CWA ,200 25,400 3, CWA ,400 31,700 2, CWA ,500 33,000 3, CWA ,800 38,200 4, CWA ,000 46,800 4, CWA ,900 4, CWA ,800 5, CWA ,800 7, CWA ,000 8,400 1, CWA ,700 10,400 1, CWA ,500 13,800 1, CWA ,500 17,400 2, CWA ,000 20,400 2, CWA ,200 23,000 3, CWA ,000 27,600 3, CWA ,500 29,400 4, CWA ,500 35,400 4, CWA ,500 41,400 4, CWA ,200 5, CWA ,400 10,100 1, CWA ,500 12,600 1, CWA ,000 15,600 2, CWA ,000 20,400 3, CWA ,500 25,800 4, CWA ORDERING INFORMATION It is vital that the information listed below is given with each evaporator order. Orders without this information may be delayed. Evaporators with options such as solenoid and expansion valves will not be processed until all the required information is given. 1. Model Number 2. Voltage, frequency and phase of motors and heaters (when applicable) 3. Refrigerant Type 4. Evaporator Temperature 5. Evaporator T.D. OPTIONAL FEATURES High efficiency PSC fan motors 460 volt motors and heaters Coated Aluminum fins or Copper Fins Baked white enamel housing Epoxy resin high throw guards for up to 50 ft. Reheat kits (not UL listed Factory mounted expansion valves Please contact your local Carlyle Certified Refrigeration Partner for all product, technical, sales and pricing issues. 102

10 ELECTRIC DEFROST / SPECIFICATIONS BTUH 10 TD Evaporator 6 FPI 4 FPI Temperature MODEL NO CFM Motor Amps¹ Heater Amps² Standard PSC 208/230V 460V Watts 230V 460V 230V 1 PH 3 PH 1 PH CWE ,400 3,600 3,700 3, ,000 CWE ,900 4,100 4,300 4, ,000 CWE ,400 4,600 4,800 5, ,000 CWE ,700 6,000 6,200 7,000 1, ,600 CWE ,100 7,500 7,800 8,700 1, ,600 CWE ,700 9,200 9,600 11,500 1, ,000 CWE ,400 12,000 12,500 14,500 2, ,000 CWE ,300 14,000 14,600 17,000 2, ,000 CWE ,000 16,400 17,100 19,200 3, ,000 CWE ,600 18,500 19,200 23,000 3, ,000 CWE ,000 21,000 21,800 24,500 4, ,000 CWE ,300 24,500 25,500 29,500 4, ,000 CWE ,600 28,000 29,100 34,500 4, ,000 CWE ,500 3,700 3,800 4, ,000 CWE ,800 7,200 7,500 8,400 1, ,000 CWE ,100 8,500 8,800 10,500 1, ,000 CWE ,000 10,500 10,900 13,000 2, ,000 CWE ,300 14,000 14,600 17,000 3, ,000 CWE ,100 18,000 18,700 21,500 4, ,000 CWE ,400 21,500 22,400 25,500 4, ,000 (1) All fan motors are wired for single phase. Standard motors are shaded pole. High efficiency PSC (Permanent Split Capacitor) motors are optional. (2) For 280/230 volt models, heaters are wired as standard for single phase on 1 through 4 fan models. 5 and 6 fan models are wired 3 phase. 460 Volt models are only available in single phase and are compatible with all 3 phase systems. HOT GAS DEFROST / SPECIFICATIONS 6 FPI 4 FPI Model Number BTUH 10 TD Evaporator Temperature Re-Evap Rev Cycle CFM Fan Motor Amps¹ Standard PSC 115V 230V 460V 115V 230V Re-Evap HEA Unmtd CWH16-36 CWG ,400 3,600 3,700 3, A CWH16-41 CWG ,900 4,100 4,300 4, A CWH16-46 CWG ,400 4,600 4,800 5, A CWH26-60 CWG ,700 6,000 6,200 7,000 1, A CWH26-75 CWG ,100 7,500 7,800 8,700 1, A CWH26-92 CWG ,700 9,200 9,600 11,500 1, A CWH CWG ,400 12,000 12,500 14,500 2, A CWH CWG ,300 14,000 14,600 17,000 2, A CWH CWG ,000 16,400 17,100 19,200 3, A CWH CWG ,600 18,500 19,200 23,000 3, A CWH CWG ,000 21,000 21,800 24,500 4, A CWH CWG ,300 24,500 25,500 29,500 4, A CWH CWG ,600 28,000 29,100 34,500 4, A CWH14-37 CWG ,500 3,700 3,800 4, A CWH24-72 CWG ,800 7,200 7,500 8,400 1, A CWH24-85 CWG ,100 8,500 8,800 10,500 1, A CWH CWG ,000 10,500 10,900 13,000 2, A CWH CWG ,300 14,000 14,600 17,000 3, A CWH CWG ,100 18,000 18,700 21,500 4, A CWH CWG ,400 21,500 22, , A (1) All fan Motors are wired for single phase Please contact your local Carlyle Certified Refrigeration Partner for all product, technical, sales and pricing issues. 103

11 PHYSICAL DATA Models Refrigerant Connections Dimensions No. (Inches) CWA CW E/H/G TXV TYPE All Liquid CWA Suction CW E/H/G Suction HG Of Hangers A B C W EXT ½ ODS 5/8 0DS / EXT 1/2 5/ / EXT 1/2 5/ / EXT 1/2 5/ / EXT 1/2 7/ / EXT 1/2 7/ / EXT 1/2 7/ / EXT 1/2 7/ / EXT 1/2 1-1/ / EXT 1/2 1-1/ / EXT 1/2 1-1/ /2 36-1/2-81-1/ EXT 1/2 1-1/ /2 36-1/2-81-1/ EXT 1/2 1-1/ /2 36-1/2-99-1/ EXT 1/2 1-1/ / / / EXT 1/2 1-1/ / / / EXT ½ ODS 5/8 0DS 5/8 0DS 5/8 0DS / EXT 1/2 5/8 5/8 5/ / EXT 1/2 5/8 5/8 5/ / EXT 1/2 5/8 5/8 5/ / EXT 1/2 7/8 7/8 5/ / EXT 1/2 7/8 7/8 5/ / EXT 1/2 7/8 7/8 5/ / EXT 1/2 1-1/8 1-1/8 5/ / EXT 1/2 1-1/8 1-1/8 5/ /2 36-1/2-81-1/ EXT 1/2 1-1/8 1-1/8 5/ /2 36-1/2-81-1/ EXT 1/2 1-1/8 1-1/8 5/ /2 36-1/2-99-1/ EXT 1/2 1-1/8 1-1/8 5/ / / / EXT 1/2 1-1/8 1-1/8 5/ / / / EXT ½ ODS 5/8 0DS 5/8 0DS 5/8 0DS / EXT 1/2 5/8 5/8 5/ / EXT 1/2 5/8 5/8 5/ / EXT 1/2 5/8 5/8 5/ / EXT 1/2 7/8 7/8 5/ /2 36-1/2 36-1/2 81-1/ EXT 1/2 1-1/8 1-1/8 5/ /2 36-1/2 36-1/2 99-1/ EXT 1/2 1-1/8 1-1/8 5/ / /2 245 Optional Extended Flare Kit available upon request for field installation. Hot Gas connections only apply to the CWH models. INSTALLATION NOTES: (1) Install 12 away from back wall. (2) Drain connection on CWA and CWE units are centered on drain pan; and on the left end (facing air discharge) on CWH and CWG units. (3) For long air throw requirements, specify high throw fan guard. (4) Unit height at drain end of hot gas models is as follows: 1,2, and 3 fan models = 15-7/8, 4,5, and 6 fan models = 16-1/4. Ship Wt. (lbs.) Please contact your local Carlyle Certified Refrigeration Partner for all product, technical, sales and pricing issues. 104

12 Medium Profile Unit Cooler FW Series AIR DEFROST 12,600 to 69,000 BTUH ELECTRIC DEFROST 10,500 to 52,000 BTUH HOT GAS DEFROST 10,500 to 52,000 BTUH MEDIUM TO LARGE WALK-IINS COOLER & FREEZER APPLICATIONS FEATURES APPLICATIONS Medium Profile unit coolers are ideally suited for a wide range of coolers and freezers. FWA models are designed for use in coolers above 35 F. FWE, FWG, and FWH units are suited for 35 F coolers, when mechanical defrosts are required, as well as for freezers with temperatures ranging down to -30 F. SIZES There are 37 models offered, with capacities from 10,500 BTUH up to 69, TD. Air flow ranges from 3,320 CFM to 9,130 CFM. HOUSING Each unit is constructed with a rust-free, heavy gauge, textured, Aluminum housing which is light weight yet extremely durable. Air and electric defrost models have hinged drain pans to allow for convenient servicing and maintenance (Hot Gas drain pans are not hinged). Slotted hangers are provided on all units for fast installation. COIL Seamless Copper tubes are staggered and mechanically expanded into heavy gauge corrugated Aluminum fins to assure maximum heat transfer. Die formed fin collars are provided for accurate fin spacing. Heavy gauge hangers are fastened directly to the tube sheet of the coil to provide high structural strength. REFRIGERATION Medium Profile unit coolers are designed for most refrigerants including, R-22, R-404A, R-134a, R-502 and R-507. Please specify system refrigerant requirements when ordering. A separate compartment is provided for all refrigerant connections which allows ample room for internal mounting of expansion valves. Medium Profile can also be used with chilled water or glycol solutions, contact factory for selection. FANS Powerful heavy duty Aluminum fans are individually balanced to provide vibration free operation. WIRE FAN GUARDS Standard heavy gauge wire fan guards are epoxy coated for corrosion resistance. Optional air straighteners are available for increased air throw when required. MOTORS All motors are high efficiency PSC, ball bearing type, life lubricated and thermally protected. Medium Profile unit coolers use either 1/8 HP, 1050 rpm or 1/3 HP, 1075 rpm motors. ELECTRICAL Available in 115V/1, 208/230/1, 208/230/3, 460/1 or 460/3. Inter-Temps can also be operated on 220/1/50, 220/3/50, 380/1/50 and 380/3/50 power. All components are factory wired to convenient screw type terminal blocks. A large compartment is supplied for all electrical components and is easily accessible by removing the end panel. AIR DEFROST Available on FWA series only, for use in coolers at +35 F and above. Complete air defrost systems are available from Carrier. ELECTRIC DEFROST These units are available as FWE models. The placement of heaters within the refrigeration coil allows for a more efficient and rapid defrost cycle than other designs. This arrangement enables the energy from the heaters to be conducted from the center of the core out, providing an even defrost pattern. All heaters are factory installed and wired to screw type terminal blocks, allowing for quick field hook up or change over from 1 to 3 phase with the installation of jumper wires. Separate, fixed defrost termination; fan delay and heater safety controls are factory mounted for optimum performance of each control function. Drain pans are heated for fast, reliable drainage. Timer and contactors are available as options. Complete electric defrost systems are available from Carrier. HOT GAS RE-EVAP DEFROST Available on all but the FWA models. These units include separate fixed defrost termination and fan delay controls which are factory mounted for optimum performance of each control function. A hot gas drain pan circuit is provided, thus eliminating the need for electric heat and additional wiring. A heat exchanger /re-evaporator is supplied with every unit. HOT GAS REVERSE CYCLE DEFROST Available on all but the FWA models. These units include separate fixed defrost termination and fan delay controls which are factory mounted for optimum performance of each control function. A hot gas drain pan circuit is provided, thus eliminating the need for electric heat and additional wiring. This unit is also used for Alternating Evaporator System. Please contact your local Carlyle Certified Refrigeration Partner for all product, technical, sales and pricing issues. 105

13 Medium Profile Unit Cooler FW Series OPTIONS Copper fins Coated fins (air and hot gas defrost models only) Galvanized steel housing Insulated drain pans Custom circuiting for chilled water or glycol applications High throw fan guards (air straighteners) Reheat kit. Adjustable DTFD Contact factory for other requirements Nomenclature AIR THROW Air throw is greatly affected by installation variables. Optimum air throw is obtained by high ceiling with no interference from beams, or return air restrictions. Medium Profile unit coolers will throw air up to 50 feet under ideal conditions, 60 to 70 feet with air straighteners. Performance Data F R E 4 E F Z P E I R MODEL CAPACITY 10 TD (R404A, R22) NUMBER CFM -30 F -20 F -10 F +10 F +25 F FW* FW* FW* FW* FW* FW* FW* MODEL CAPACITY 10 TD (R404A, R22) NUMBER CFM -30 F -20 F -10 F +10 F +25 F F FW* R FW* E 6 FW* E F FW* Z P FW* E I R FW* FW* FW* * E = Electric defrost H=Hot gas defrost-re evap G = Hot gas defrost-reverse cycle C O 4 O F L P E I R MODEL BTUH MODEL BTUH MODEL CFM BTUH NUMBER CFM +25 F NUMBER CFM +25 F NUMBER +25 F FWA FWA FWA FWA C FWA C FWA FWA O 6 FWA O 8 FWA FWA O F FWA O F FWA FWA L P FWA L P FWA E I E I FWA FWA FWA R R FWA FWA FWA FWA FWA FWA For 50 Hz applications, multiply BTU/H capacity by.94 correction factor. Please contact your local Carlyle Certified Refrigeration Partner for all product, technical, sales and pricing issues. 106

14 ELECTRICAL DATA. F R 4 E E F Z P E I R F R 6 E E F Z P E I R TOTAL MOTOR AMPS 60 HZ ELECTRIC DEFROST AMPERAGE HZ 208/ V MODEL 115 V V 1 PH 208 V 230 V 460 V NUMBER 1 PH 1 PH 3 PH 1 PH 3 PH 1 PH 3 PH 1 PH 3 PH WATTS FW* FW* FW* FW* FW* FW* FW* FW* FW* FW* FW* FW* FW* FW* FW* * E = Electric defrost G=Hot gas defrost - Reverse cycle H= Hot gas Re-Evap 115V Available for Hot Gas Defrost units only. AIR DEFROST UNITS C O 4 O F L P E I R TOTAL MOTOR AMPS 60 HZ TOTAL MOTOR AMPS 60 HZ MODEL 115V 208/230V 460V MODEL 115V 208/230V 460V NUMBER 1PH 1PH 3PH 1PH NUMBER 1PH 1PH 3PH 1PH FWA FWA FWA C FWA FWA O 6 FWA FWA O F FWA FWA L P FWA FWA E I FWA R FWA FWA FWA FWA C O 8 O F L P E I R TOTAL MOTOR AMPS 60 HZ MODEL 115V 208/230V 460V NUMBER 1PH 1PH 3PH 1PH FWA FWA FWA FWA FWA FWA FWA FWA Please contact your local Carlyle Certified Refrigeration Partner for all product, technical, sales and pricing issues. 107

15 PHYSICAL DATA F R 4 E E F Z P E I R F R 6 E E F Z P E I R AIR DEFROST UNITS C O 4 O L F E P R I MODEL NUMBER MODEL NUMBER FAN DIA (in) FAN DIA (in) MOTOR DATA QTY HP RPM MOTOR DATA QTY HP RPM OPTIONAL HEAT EXCH (UNMTD) OPTIONAL HEAT EXCH (UNMTD) RE-EVAP HEAT EXCH (UNMTD) RE-EVAP HEAT EXCH (UNMTD) LIQUID ODS LIQUID ODS CONNECTIONS (in) SUCTION ODS CONNECTIONS (in) SUCTION H.G. ODS ODS DRAIN MPT FWA / RXH150 N/A 1/2 7/8 N/A 3/4 115 FWA / RXH150 N/A 1/2 7/8 N/A 3/4 130 FWA / RXH150 N/A 1/2 7/8 N/A 3/4 280 FWA / RXH250 N/A 1/2 1 1/8 N/A 3/4 310 FWA / RXH250 N/A 7/8 1 1/8 N/A 3/4 345 FWA / RXH250 N/A 7/8 1 1/8 N/A 3/4 375 FWA / RXH250 N/A 7/8 1 3/8 N/A 3/4 400 FWA / RXH350 N/A 7/8 1 3/8 N/A 3/4 505 H.G. ODS DRAIN MPT FW* / RXH150 HEA3A 1/2 1 1/8 7/8 3/4 120 FW* / RXH150 HEA3A 1/2 1 1/8 7/8 3/4 135 FW* / RXH150 HEA3A 1/2 1 1/8 7/8 3/4 285 FW* / RXH250 HEA4A 1/2 1 3/8 7/8 3/4 315 FW* / RXH350 HEA4A 7/8 1 3/8 7/8 3/4 350 FW* / RXH350 HEA4A 7/8 1 5/8 7/8 3/4 435 FW* / RXH500 HEA5A 7/8 1 5/8 7/8 3/4 530 FW* / RXH150 HEA3A 1/2 1 1/8 7/8 3/4 125 FW* / RXH150 HEA3A 1/2 1 1/8 7/8 3/4 140 FW* / RXH150 HEA3A 1/2 1 1/8 7/8 3/4 295 FW* / RXH250 HEA4A 1/2 1 3/8 7/8 3/4 320 FW* / RXH350 HEA4A 7/8 1 3/8 7/8 3/4 365 FW* / RXH350 HEA4A 7/8 1 5/8 7/8 3/4 450 FW* / RXH500 HEA5A 7/8 1 5/8 7/8 3/4 490 FW* / RXH500 HEA5A 7/8 1 5/8 7/8 3/4 535 SHIP WT (lbs.) SHIP WT (lbs.) C O 6 O L F E P R I C O 8 O L F E P R I FWA / RXH150 N/A 1/2 7/8 N/A 3/4 120 FWA / RXH150 N/A 1/2 7/8 N/A 3/4 140 FWA / RXH150 N/A 1/2 7/8 N/A 3/4 290 FWA / RXH250 N/A 1/2 1 1/8 N/A 3/4 320 FWA / RXH250 N/A 7/8 1 1/8 N/A 3/4 360 FWA / RXH250 N/A 7/8 1 1/8 N/A 3/4 395 FWA / RXH250 N/A 7/8 1 3/8 N/A 3/4 415 FWA / RXH350 N/A 7/8 1 3/8 N/A 3/4 520 FWA / RXH150 N/A 1/2 7/8 N/A 3/4 125 FWA / RXH150 N/A 1/2 7/8 N/A 3/4 145 FWA / RXH250 N/A 1/2 1 1/8 N/A 3/4 295 FWA / RXH250 N/A 1/2 1 1/8 N/A 3/4 330 FWA / RXH250 N/A 7/8 1 1/8 N/A 3/4 370 FWA / RXH250 N/A 7/8 1 3/8 N/A 3/4 390 FWA / RXH350 N/A 7/8 1 3/8 N/A 3/4 430 FWA RXH350 N/A 7/8 1 3/8 N/A 3/4 540 Please contact your local Carlyle Certified Refrigeration Partner for all product, technical, sales and pricing issues. 108

16 DIMENSIONS ALL MODELS ELECTRIC AND HOT DIMENSIONS GAS DEFROST AIR DEFROST MODELS FIG. W A B FW* FW* FWA FWA FWA FW* FW* FWA FWA FWA FW* FW* FWA FWA FWA FWA FWA FWA FW* FW* FWA FWA FWA /2 FW* FW* FWA FWA /2 FW* FWA FW* FW* FWA FWA FWA FW* FW* FWA FWA FWA * E = Electric defrost H = Hot gas defrost - Re evap G = Hot gas defrost - Reverse cycle 3/4 MPT drain connections on all units Please contact your local Carlyle Certified Refrigeration Partner for all product, technical, sales and pricing issues. 109

17 Large Profile Unit Cooler HW Series FEATURES AIR DEFROST - 16,400 to 273,000 BTUH ELECTRIC DEFROST - 11,800 to 248,000 BTUH HOT GAS DEFROST - 11,800 to 248,000 BTUH LARGE WALK-INS & WAREHOUSES COOLER & FREEZER APPLICATIONS APPLICATION - Large Profile unit coolers are ideally suited for a wide range of large coolers, freezers and blast freezers. The HW*U and HW*L models are designed for use below +25 F room temperature. The HW*M and HWAH models are designed for coolers in the medium and high temperature ranges. SIZES - There are 61 sizes available, ranging in capacity from 11,800 to 273, TD, and ranging in air flow from 2,720 to 29,900 CFM. HOUSING - Rust-free, heavy gauge textured Aluminum; lightweight and durable. Air and electric defrost models have hinged drain pans to allow for convenient servicing and maintenance (Hot Gas drain pans are not hinged). LIFTING LEGS - 2 fan models and larger are shipped upright with removable lifting legs, allowing the unit to be installed quickly, and easily with a forklift. Slotted hangers are provided for fast installation. COIL - Seamless Copper tubes are mechanically expanded into heavy gauge corrugated Aluminum fins to assure maximum heat transfer. Die formed fin collars are provided for accurate fin spacing. Hangers are fastened directly to the tube sheets of the coil to provide high structural strength. All units are dehydrated, sealed and shipped with a nitrogen holding charge. REFRIGERANTS - For use with direct expansion, R-22, R-404A, and R-507. Specify refrigerant when ordering. A separate compartment is provided for all refrigeration connections, allowing ample room for internal mounting of expansion valve(s). Large Profile units can also be used for chilled water or glycol solutions, contact factory for selection. FANS - Powerful, heavy-duty Aluminum fans are individually balanced to provide vibration-free operation. Wire fan guards are epoxy coated for corrosion resistance. Optional air straighteners are available for increased air throw. MOTORS - All motors are high efficiency PSC, ball bearing type, life lubricated and thermally protected. HW*U and HW*L models use 3/ RPM or 3/4 HP, 1625 RPM motors. HW*M and HWAH models use 1/3 HP or 3/4 HP, 1075 RPM motors. ELECTRICAL - Available in 115/1, 208/230/1, 208/230/3, 460/1 and 460/3 (see page 10). Large Profile units can also be operated on 220/1/50, 220/3/50, 380/1/50, and 380/3/50 power (contact factory for details). All components are factory wired to convenient screw-type terminal blocks. A large compartment is supplied for all electrical components and is easily accessible by removing the end panel. AIR DEFROST - Available on HWAM and HWAH series only for use in coolers at +35 F and above. ELECTRIC DEFROST - Available on all but the HWAH models. Placement of the heaters within the refrigeration coil allow for a more efficient and rapid defrost cycle. This arrangement enables heat to be conducted from the center of the core out, for a more even defrost pattern. All heaters are factory wired to screw-type terminal blocks, allowing for a quick field change over from 1 to 3 phase or 230V to 460V and vice versa with the use of jumpers. An adjustable, remote bulb defrost termination and fan delay (DTFD) is mounted and wired. Drain pans are heated for fast, reliable drainage. Timer and contactors are available as options. Complete Electric Defrost systems are available from Carrier. HOT GAS RE-EVAP DEFROST - Available on all but the HWAH models. Includes an adjustable defrost termination and fan delay (DTFD), factory installed. A hot gas drain circuit is supplied, thus eliminating the need for electric heat and additional wiring. A Heat Exchanger/Re-Evaporator is supplied with every unit. Refer to the current Technical Bulletin HG for piping. Complete Hot Gas Re-Evap systems are available from Carrier, contact factory. HOT GAS REVERSE CYCLE DEFROST - Available on all but the HWAH models. Includes an adjustable defrost termination and fan delay. (DTFD) factory installed. A hot gas drain pan circuit is supplied, thus eliminating the need for electric heat and additional wiring. Refer to the current Technical Bulletin HG For piping. This unit is also used for Alternating Evaporator Systems. Please contact your local Carlyle Certified Refrigeration Partner for all product, technical, sales and pricing issues. 110

18 Large Profile Unit Cooler HW Series OPTIONS Copper fins. Inherent 3 phase motors. Coated fins (air and hot gas models only). Ultra low temperature motor grease for applications down to -60 F suction temperature. Galvanized steel casing. Insulated drain pans. High pressure propeller fans (up to 0.5 external pressure) Custom circuiting for chilled water or glycol applications. High air throw fan guards. AIR THROW Air throw is affected by installation variables. Optimum air throw is obtained by high ceiling with no interference from beams, product or return air restrictions. MODEL WIRE FAN GUARD FAN GUARD / AIR STRAIGHTENER HW*U / HW*L feet feet HW*M / HWAH feet feet Please contact your local Carlyle Certified Refrigeration Partner for all product, technical, sales and pricing issues. 111

19 PERFORMANCE DATA F R 4 E E F Z P E I R F R 6 E E F Z P E I R CAPACITY 10 TD (404A, R-22) MODEL SUCTION TEMPERATURE NUMBER CFM -30 F -20 F -10 F +10 F HW*U HW*U HW*U HW*U HW*U HW*U HW*U HW*U HW*U HW*L HW*L HW*L HW*L HW*L HW*L HW*L HW*L HW*L HW*L HW*L HW*L HW*L HW*L HW*L HW*L HW*L HW*L HW*L HW*L HW*L C O 6 O L F E P R I MODEL NUMBER CFM CAPACITY BTUH@10 TD +20 F MODEL NUMBER CFM CAPACITY BTUH@10 TD +20 F HW*M HWAH HW*M HWAH HW*M HWAH HW*M HWAH C HW*M HWAH O 8 HW*M O HWAH HW*M L F HWAH HW*M E P HWAH HW*M R I HWAH HW*M HWAH HW*M HWAH HW*M HWAH HW*M HWAH HW*M HWAH HW*M HWAH HWAH Please contact your local Carlyle Certified Refrigeration Partner for all product, technical, sales and pricing issues. 112

20 F R 4 E E F Z P E I R F R 6 E E F Z P E I R C O 6 O L F E P R I C O 8 O L F E P R I MODEL NUMBER FAN DIA (In.) MOTOR DATA (1) RE-EVAP CONNECTIONS (In.) 2 OPTIONAL HEAT HEAT EXCH. SUCT. H.G. QTY HP RPM EXCH. LIQUID (UNMTD.) ODS ODS (UNMTD.) DRAIN MPT Ship Wt.(Lbs.) HW*U / RHX-150 HEA2A 1/2FL 1-1/8 7/8 3/4 190 HW*U / RHX-250 HEA3A 7/8 ODS 1-3/8 7/8 3/4 370 HW*U / RHX-350 HEA4A 7/8 ODS 1-5/8 7/8 3/4 440 HW*U / RHX-350 HEA5A 7/8 ODS 1-5/8 7/8 3/4 570 HW*U / RHX-500 HEA6A 7/8 ODS 2-1/8 1-1/8 1-1/4 665 HW*U / (2) RHX-500 (2) HEA5A (2) 7/8 ODS (2) 2-1/8 1-1/8 1-1/4 875 HW*U / (2) RHX-500 (2) HEA5A (2) 7/8 ODS (2) 2-1/8 1-1/8 1-1/4 900 HW*U / (2) RHX-500 N/A (2) 7/8 ODS (2) 2-1/8 1-1/8 1-1/ HW*U / (2) RHX-500 N/A (2) 1-1/8 ODS (2) 2-5/8 1-1/8 1-1/ HW*L / RHX-150 HEA3A 1/2FL 1-1/8 7/8 3/4 180 HW*L / RHX-150 HEA3A 1/2FL 1-1/8 7/8 3/4 200 HW*L / RHX-150 HEA3A 5/8 ODS 1-1/8 7/8 3/4 220 HW*L / RHX-250 HEA4A 7/8 ODS 1-3/8 7/8 3/4 370 HW*L / RHX-250 HEA4A 7/8 ODS 1-3/8 7/8 3/4 400 HW*L / RHX-350 HEA4A 7/8 ODS 1-5/8 7/8 3/4 425 HW*L / RHX-350 HEA5A 7/8 ODS 1-5/8 7/8 3/4 446 HW*L / RHX-500 HEA5A 7/8 ODS 2-1/8 7/8 3/4 525 HW*L / RHX-500 HEA5A 7/8 ODS 2-1/8 7/8 3/4 585 HW*L / RHX-500 HEA6A 7/8 ODS 2-1/8 7/8 3/4 620 HW*L / RHX-500 HEA6A 7/8 ODS 2-1/8 7/8 3/4 645 HW*L / RHX-500 HEA6A 1-3/8 ODS 2-1/8 1-1/8 1-1/4 675 HW*L / RHX-500 (2) HEA5A 7/8 ODS 2-1/8 1-1/8 1-1/4 726 HW*L / RHX-500 (2) HEA5A (2) 7/8 ODS (2) 2-1/8 1-1/8 1-1/4 850 HW*L / (2) RHX-500 (2) HEA5A (2) 7/8 ODS (2) 2-1/8 1-1/8 1-1/4 885 HW*L / (2) RHX-500 (2) HEA6A (2) 7/8 ODS (2) 2-1/8 1-1/8 1-1/4 895 HW*L / (2) RHX-500 (2) HEA6A (2) 7/8 ODS (2) 2-1/8 1-1/8 1-1/4 910 HW*L / (2) RHX-500 N/A (2) 1-1/8 ODS (2) 2-1/8 1-1/8 1-1/ HW*L / (2) RHX-500 N/A (2) 1-1/8 ODS (2) 2-1/8 1-1/8 1-1/ HW*L / (2) RHX-500 N/A (2) 1-3/8 ODS (2) 2-5/8 1-1/8 1-1/ HW*L / (2) RHX-500 N/A (2) 1-3/8 ODS (2) 2-5/8 1-1/8 1-1/ HW*M / RHX-150 HEA3A 1/2FL 7/8 7/8 3/4 200 HW*M / RHX-150 HEA3A 5/8 ODS 7/8 7/8 3/4 220 HW*M / RHX-250 HEA4A 5/8 ODS 1-1/8 7/8 3/4 360 HW*M / RHX-250 HEA4A 5/8 ODS 1-1/8 7/8 3/4 400 HW*M / RHX-250 HEA4A 5/8 ODS 1-1/8 7/8 3/4 425 HW*M / RHX-250 HEA5A 5/8 ODS 1-1/8 7/8 3/4 446 HW*M / RHX-350 HEA5A 5/8 ODS 1-3/8 7/8 3/4 585 HW*M / RHX-350 HEA6A 7/8 ODS 1-3/8 7/8 3/4 620 HW*M / RHX-350 HEA6A 7/8 ODS 1-3/8 1-1/8 1-1/4 675 HW*M / RHX-500 (2) HEA5A 7/8 ODS 1-3/8 1-1/8 1-1/4 726 HW*M / (2) RHX-350 (2) HEA5A 7/8 ODS 1-5/8 1-1/8 1-1/4 830 HW*M / (2) RHX-350 (2) HEA5A 1-1/8 ODS 1-5/8 1-1/8 1-1/4 885 HW*M / (2) RHX-500 (2) HEA6A 1-1/8 ODS 2-1/8 1-1/8 1-1/4 910 HW*M / (2) RHX-500 N/A 1-5/8 ODS 2-5/8 1-1/8 1-1/ HW*M A 1-8 ODS HWAH / RHX-150 N/A 5/8 ODS 7/8 N/A 3/4 210 HWAH / RHX-150 N/A 5/8 ODS 7/8 N/A 3/4 230 HWAH / RHX-250 N/A 5/8 ODS 1-1/8 N/A 3/4 370 HWAH / RHX-250 N/A 5/8 ODS 1-1/8 N/A 3/4 410 HWAH / RHX-250 N/A 5/8 ODS 1-1/8 N/A 3/4 435 HWAH / RHX-250 N/A 5/8 ODS 1-1/8 N/A 3/4 458 HWAH / RHX-250 N/A 7/8 ODS 1-3/8 N/A 3/4 550 HWAH / RHX-350 N/A 7/8 ODS 1-3/8 N/A 3/4 600 HWAH / RHX-350 N/A 7/8 ODS 1-3/8 N/A 3/4 635 HWAH / RHX-350 N/A 7/8 ODS 1-3/8 N/A 1-1/4 690 HWAH / RHX-500 N/A 7/8 ODS 1-3/8 N/A 1-1/4 746 HWAH / (2) RHX-350 N/A 7/8 ODS 1-3/8 N/A 1-1/4 785 HWAH / (2) RHX-350 N/A 7/8 ODS 1-5/8 N/A 1-1/4 905 HWAH / (2) RHX-500 N/A 7/8 ODS 2-1/8 N/A 1-1/4 930 HWAH / (2) RHX-500 N/A 1-7/8 ODS 2-5/8 N/A 1-1/ HWAH / (2) RHX-500 N/A (2) 1-3/8 ODS (2) 2-5/8 N/A 1-1/ (1) All motors are single phase. All three fan models and larger are delta wired for three phase power. Inherent three phase motors are available, contact factory. (2) All Large Profile units are custom circuited for optimum performance and operating efficiency. Should conditions vary from those listed to the right, *connection sizes and quantity may be subject to change, contact factory to confirm. * Connection sizes are based on the following criteria: HW*U: - 30 ST, 10 TD R-404A HW*L: - 20 ST, 10 TD R-404A HW*M: +20 ST, 10 TD R-22 HWAH: +25 ST, 10 TD R-22 Please contact your local Carlyle Certified Refrigeration Partner for all product, technical, sales and pricing issues. 113