CTIOS Agent Softphone Login Failure

Transcription

1 CTIOS Agent Softphone Login Failure Document ID: Contents Introduction Prerequisites Requirements Components Used Conventions Update CTIOS with Blank Password CTIOS Login Error CAD Login Error CECTI Error This is a shared line Related Information Introduction This document describes one reason why Agent Softphone for Cisco Computer Telephony Integration Object Server (CTIOS) fails to log into the server in a Cisco IP Contact Center (IPCC) Enterprise environment. Prerequisites Requirements Cisco recommends that you have knowledge of these topics: Cisco IPCC Enterprise configuration Computer Telephony Integration Object Server (CTIOS) Components Used The information in this document is based on these software and hardware versions: Cisco IPCC Enterprise Edition version 6.x and later CTIOS version 6.x and later The information in this document was created from the devices in a specific lab environment. All of the devices used in this document started with a cleared (default) configuration. If your network is live, make sure

2 that you understand the potential impact of any command. Conventions Refer to Cisco Technical Tips Conventions for more information on document conventions. 1 When the CTIOS Agent Softphone tries to log into the CTIOS Server, the login fails, and an IPCC error message appears (see Figure 1). Figure 1 IPCC Error Message In addition, the Agent ID and other agent related information are blank (see Figure 2). Figure 2 Cisco CTIOS Agent Softphone The corresponding log for the Peripheral Interface Manager (PIM) process displays these messages: 15:50:30 pg1a pim1 Trace: TelephonyDriver:Login IP address Login Device ID 2001 Device Target IP address 2001 *****15:50:30 pg1a pim1 Trace: BaseDevice:: CreateNewClientInstance: Invalid device type specified. Unsupported************* 15:50:30 pg1a pim1 Trace: TelephonyDriver::CSTASetAgentState: Agent 2001 login failed Create of Client Instance failed.nettargetid= :50:30 pg1a pim1 Trace: DeskLinkPeripheral::SetAlert (TelephonyDriver::CSTASetAgentState) Setting ERROR Alert #27 15:50:30 Create Instance 1 This problem occurs due to a configuration issue. When you configure the device target, you can specify configuration parameters that represent strings that the device receives during initialization. You can use the Configuration parameters field to enter specific parameters. The Configuration parameters field contains these three parameters:

3 /devtype: Device type /dn: Full phone number /ext: Extension /devtype and /dn are required parameters. /ext is optional. Here, the device is a Cisco CTIOS Agent Softphone. Therefore, the /devtype must be ciscophone (see Figure 3). CTIOS Agent Softphone login failure occurs if you spell ciscophone incorrectly during configuration. Correct the spelling of ciscophone in order to solve the problem. Figure 3 Configuration Parameters 2 Within the CTIOS client, all of the buttons are greyed out and the login option does not appear. This issue is documented by Cisco bug ID CSCta89546 (registered customers only). 2 Delete this registry key in order to resolve the issue: HKEY_LOCAL_MACHINE\SOFTWARE\Cisco Systems, Inc.\Ctios\CTIOS_ipba\ CTIOS1\EnterpriseDesktopSettings\All Desktops\IPCCSilentMonitor\Name\Settings StopSMNonACDCall Update CTIOS with Blank Password When you log in to CTIOS with a blank password, you receive the invalid username and password error. In order to resolve this issue, set a blank password with the Person Bulk Edit tool. This is documented in Cisco bug ID CSCty89124 (registered customers only). CTIOS Login Error

4 After you perform an upgrade to CUCM 8 and UCCE 8, you are unable to log in to CTIOS with 7940 phones. This error message is also received: error An attempt has been made to log in to a device that has unsupported IP addressing mode configured on UCM. Supported IP addressing mode for agents devices is IPv4 This issue occurs when both IPV4 and IPV6 are enabled. In order to resolve this issue, update the Common Device Configuration to turn off IPV6 and lock the phone to IPV4 only. CAD Login Error The Error [10159] This is a shared line. error is received when you try to add a new agent. An extension on the agent phone is shared by one or more devices. Note: This is only for one agent and is not a system wide issue. You need to turn up the tracing on the jgw logs. In order to do this on the active jgw, issue this command: C:\>procmon <cust_inst> <node> jgw<jtapi instance> >>>trace lock* /off >>>trace thread* /off >>>trace JT_TPREQUESTS /on >>>trace JT_JTAPI_EVENT_* /on >>>trace JT_PIM_EVENT /on >>>trace JT_ROUTE_MESSAGE /on >>>trace *CONF* /on >>>trace JT_LOW_LEVEL_API_JTAPI* /on In order to turn tracing off, enter >>>trace * /off. Based on the traces, perform a cti manager restart after office hours in order to resolve the issue. CECTI Error This is a shared line Some agents recently received the Error This is a shared line error message when they tried to log in to the CTIOS Toolkit. This error can be found in the JTAPI GW log. Note: This is an ICM deployment with CUCM 8.5.1, and the agents are using Extension Mobility (EM).

5 The agent in this example used EM on IP Communicator along with an IP phone. If the agent does not log out EM properly from IP Communicator before closing it or terminates IP Communicator incorrectly, the EM extension can be stuck in CUCM. As a result, CUCM will report it as a shared line when the agent logs in with an EM profile to the IP phone. For agents using their EM profiles on IP Communicators, complete these steps in order to resolve the issue: 1. Delete and then re create their EM profile on CUCM. 2. Log in with the re created EM profile on the IP phone, and test CTIOS. Note: You will need to log out from EM on the IP Communicator before you close them. Related Information Technical Support & Documentation Cisco Systems Contacts & Feedback Help Site Map Cisco Systems, Inc. All rights reserved. Terms & Conditions Privacy Statement Cookie Policy Trademarks of Cisco Systems, Inc. Updated: Jul 31, 2012 Document ID: 65747