Operation Manual, Parts Directory and Price List

Transcription

1 Operation Manual, Parts Directory and Price List Vertical Door Coolers A Family Company Manufacturing In The USA Since 969 Self-Contained Models - BB, BB36, BB60*, BB8*, BB08*, ND5*, ND7*, ND9*, FV*, FV8*, LP60*, LP8*, LP08*, PT60, PT8, PT08, KC, KC8, KC5, KC7, KC8* Remote Models - BB, BB8, BB7, BB96, LP8, LP7, LP96, PT8, PT7, PT96 Dry Storage Models - DS, DS8, DS7, LPDS *See Page for Important Cooler Serial Number Information BB60-L-XSH(LR) FV-BS(L) BB7-R-N(LLR) shown with optional wood panel doors PT60-L-LLH(LR/RL) Glastender, Inc. 500 North Michigan Road Saginaw, MI Fax / Rev Glastender, Inc.

2 Service and Parts Cooler Serial Number Information... Terms and Conditions... 3 arranty... Installation Introduction... 5 Utility Requirements and Connections... 5 Uncrating and Start-Up Instructions... 5 Operation... 5 Cleaning Instructions Floor Sealing Instructions... 6 BB Minimum Air Flow Clearance Diagram... 6 Cooler Installation Checklist... 7 Cooler Design Change... 8 Specifications Electrical and Refrigeration Specifications... 9 iring Diagrams Endwall Models... 0 Self-Contained Models... Remote Models... Remote Models with Solenoid Control... 3 Built-in Fluorescent Light Fixtures... 3 BB Self-contained and KC Models... Replacement Parts Compressor and Condenser Related Parts BB Self-Contained & KC... 5 BB LP60, LP8, LP08, and Non Endwall BB60, BB8, BB08, ND5, ND7, ND9, KC7, and KC BB36, BB60, ND5, and KC5 Endwall... 8 BB8, BB08, ND7, ND9, KC7, and KC8 Endwall... 9 KC PT60, PT8, PT08... FV and FV8... Evaporator and Related Parts Doors and Related Parts Shelving, Racks and Related Parts Refrigeration Compartment Covers Volt Electrical Parts Fax /

3 Cooler Serial Number Information BB & ND Cooler Serial Number Information This manual is specific to self-contained BB60, BB8, BB08, ND5, ND7, and ND9 coolers prior to the serial numbers and dates listed below. BB60R 3363F 0/6/09 BB60L 35F 03/03/09 BB8R 357F 03/0/09 BB8L 356F 03/0/09 BB08R 35F 03/0/09 BB08L 36F 0/7/09 ND5R 359F 03/09/09 ND5L 3559F 03//09 ND7R 3906F 0/08/09 ND7L 375F 03//09 ND9R 36F 0/09/09 ND9L 375F 06/0/09 FV Cooler Serial Number Information This manual is specific to self-contained FV coolers prior to the serial numbers and dates listed below. FV SN 33788F and excluding SN 3753F & SN 33F FV8 SN 33788F and excluding SN 3796F LP Cooler Serial Number Information This manual is specific to self-contained LP coolers prior to the serial numbers and dates listed below. LP60R SN 38786F LP60L SN 38783F LP8R SN 39050N LP8L SN 3877N LP08R SN 33070N LP08L SN 3906N KC Cooler Serial Number Information This manual is specific to self-contained KC8 coolers with serial numbers beginning with Fax /

4 Terms and Conditions Prices: All prices are LIST. Applicable taxes will be added. Quotations: Unless otherwise stated, quotations are effective for 30 days only. Acceptance: All orders are subject to acceptance by Glastender, Inc. s headquarters in Saginaw, Michigan. Possession of the Product Directory and Price List is not an offer to sell. Shipments: F.O.B. factory in Saginaw, Michigan. Freight terms are Third Party or Collect if shipped directly to you. Prepay and Add to Invoice freight terms are available upon request. The approximate shipping weights of all products are listed with the prices. Partial shipments will be made unless otherwise specified by the customer. Surface freight classifications are: Glasswashers - Class 5 All Underbar Equipment (including Bar Die) Class 50 Portable Bars - Class 50 Remote refrigerators (i.e., no compressor) or dry storage back bar equipment - Class 5 Self-contained refrigeration equipment - Class 50 Ice Display Units (IDU and GDU) - Class 85 Lighted Liquor Displays - Class 85 Beer line chillers and beer towers (beverage dispensing equipment) - Class 9.5 Bottle Disintegration System - Class 50 Ice Cream Freezers - Class 77.5 All small items are evaluated to see the most cost effective means for shipment. Many small items ship via UPS or FedEx; however, when dimensional weight is excessive, LTL carriers are the most cost effective choice. Spare parts orders received before :00 PM EST can usually be shipped the same day. The order department is happy to assist with routing or shipping questions. Payment Terms: Cash should be included with all orders unless credit terms have been arranged. To establish credit, banking and trade references are required. A convenient credit application is available upon request. Payment via credit card is not our normal means of receiving payment. Visa and MasterCard will be accepted, but must be charged at the time of shipment. In addition, a payment via credit card for orders totaling more than $500 will incur a 3% convenience fee on the total transaction amount. Delivery: The majority of equipment is manufactured to order and typically ships within three to six weeks after complete order information is received by the factory. In-stock equipment typically ships within two to three days of the factory receiving complete order information. Returns: Items specified as Manufactured to Order are NOT returnable. A Return Authorization number must be issued by the factory in advance for any items that are returnable. The number MUST be noted on the outside of the returned package. Returns must be received within 90 days of the issue date. Shipping charges must be prepaid. A minimum 0% restocking charge will be applied to all authorized returns if received in new, unused condition in the original packaging. The above conditions apply to spare part returns, except spare part returns must be received within 30 days of original shipment for electronic or electrical parts or within 90 days for all other parts. Loss or Damage: For customer routed shipments, Glastender, Inc. is not responsible for any loss, damage, or delay of merchandise during shipment. Such transit claims must be filed with the carrier. Merchandise must be examined on arrival. If shortages occur, Glastender, Inc. must be notified in writing within five (5) days of delivery to honor any shortage claim. Glastender will assume responsibility for freight claims on Prepay and Add shipments but the customer must inspect freight and note any damage upon receipt. Failure to do so may result in losses at the customer s expense. Custom Orders: Custom orders must be paid in advance and are not subject to cancellation. Laminates: Some products include common, readily available plastic laminates of the customer s selection. There may be an additional charge if uncommon varieties are ordered. 07// Fax /

5 arranty Statement APPLICAE TO ALL PRODUCTS SOLD ITHIN THE UNITED STATES AND CANADA Glastender, Inc. warrants all products to be free of defects in material and workmanship. One-year labor and parts warranty applies to all glasswashers, self-contained refrigeration models, and BDS model bottle disintegration units. In established areas, a start up is included with GT- and GT-30 model glasswashers. arranty is effective for one year from the date of installation or up to 8 months from date of factory shipment, whichever occurs sooner. Glastender, Inc. will replace any part or assembly found defective under normal use and service. For warranty labor claims beyond 5 months from the date of factory shipment, proof of date of installation or occupancy must be provided. Authorization for labor must be obtained from Glastender within the warranty period and prior to the service being performed. Labor warranty applies to the United States and Canada only. Remote refrigeration models and beer line chillers include a one-year parts warranty only. There is no labor warranty on these products. Field replacement parts not covered under the original warranty include a 90-day part warranty from the date of installation. FOUR YEAR ADDITIONAL COMPRESSOR ARRANTY: Glastender will warrant to the original user the compressor for all selfcontained refrigeration models for an additional four years following the regular one-year warranty period. This plan applies to the compressor only. A completed warranty claim form MUST accompany all returned defective parts or assemblies. Upon request, a defective part or assembly must be returned to Glastender, Inc., Saginaw, Michigan, with all transportation and delivery charges prepaid. arranty repairs or replacements will be shipped FOB factory in Saginaw, Michigan. Reimbursement for applicable freight charges covers ground service only. Glastender provides in-warranty repairs during a service company s regular working days and hours. There is no provision for payment of a premium rate during overtime hours. hen warranty service is requested during other than normal working hours, the end user will be charged the premium portion of the overtime rate. The warranty covers substantiated travel expenses for up to hours / 00 miles round trip up to a maximum of $50. Any additional costs due to installations that require extra work, time, or travel to gain access for service are the sole responsibility of the equipment purchaser. Any exceptions to these travel and access limitations must be pre-approved by a factory representative. The warranty does not cover equipment subjected to accidents, freight damage, alterations from the original design, improper power and/or plumbing hookups, improper chemical use, general misuse, or lack of routine required maintenance as determined by Glastender, Inc. Installation, normal control adjustments, general maintenance, correcting an installation error, or service calls that reveal the unit is functioning normally will not be reimbursed under warranty. Condenser coils on self-contained refrigeration products must be cleaned regularly. Failure to provide adequate air flow to a refrigeration unit will void the warranty. Glastender shall not be liable for loss of use, revenue, or profit, or for any other indirect, incidental, special, or consequential damage including, but not limited to, product spoilage or loss. This warranty is conditioned upon Glastender receiving notice of any defect subject to this warranty within sixty (60) days of its discovery by the end user or dealer. All products are warranted only for the initial place of installation. Removal of a product automatically terminates this warranty. SECOND YEAR EXTENDED PARTS & LABOR ARRANTY: Glastender s one-year parts and labor warranty on self-contained refrigeration units, excluding beer line chillers, can be extended to two years with the purchase of a two year parts and labor warranty. Specify part number ER ($50 net price) when ordering. EXPORT ARRANTY - One year parts only. EXCLUSION OF ARRANTIES EXCEPT AS PROVIDED ABOVE, GLASTENDER MAKES NO ARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED ARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT. LIMITATION OF REMEDIES AND DAMAGES If Buyer makes a valid and timely claim as outlined above, Glastender s liability and Buyer s remedies under this agreement will be limited solely to labor charges authorized and/or replacement or credit, at Glastender s option, with respect to Products returned at Buyer s expense within thirty (30) days after warranty repair. GLASTENDER S LIABILITY ILL IN NO EVENT BE GREATER IN AMOUNT THAN THE PURCHASE PRICE OF THE RETURNED PRODUCTS. GLASTENDER ILL NOT BE LIAE UNDER ANY CIRCUMSTANCE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, INCLUDING, BUT NOT LIMITED TO, LABOR COSTS EXCEPT AS COVERED UNDER OUR ARRANTY, LOST PROFITS OR THE LOSS OF PERISHAE PRODUCTS RESULTING FROM THE USE OF OR INABILITY TO USE OUR PRODUCTS OR FROM OUR PRODUCTS INCORPORATION INTO OR BECOMING A COMPONENT OF ANY OTHER PRODUCT. NEITHER PARTY ILL HAVE ANY NEGLIGENCE OR OTHER TORT LIABILITY TO THE OTHER, OR TO ANY THIRD PARTY, ARISING FROM ANY BREACH OF THIS AGREEMENT. GOVERNING LA - JURISDICTION The terms and conditions of an order are to be governed and construed according to the laws of the State of Michigan, without regard to conflict of laws principles. Buyer hereby consents to the jurisdiction and venue of the courts located in Saginaw County, Michigan. No representative, distributor, dealer, or any other person is authorized to modify this warranty. This warranty replaces all other written or verbal warranties. NOTE: Glastender, Inc. s policy of constant quality improvement means that prices, specifications, and policies are subject to change without notice. Questions regarding this warranty should be directed to Glastender s arranty Administrator IMPORTANT!! Attention Service Companies Please review the important warranty information on this page. If you believe a service call should be covered by the factory, please call the factory for authorization between 8AM and 5PM EST, Monday through Friday Fax /

6 Installation Introduction This manual describes the operational features of Vertical Door Coolers. Please review this information before attempting installation and operation. Long term, trouble-free service will follow if good housekeeping and maintenance procedures are followed. Thank you for selecting Glastender, Inc. products. Utility Requirements and Connections Electrical: 5 Volt AC, Phase, 60 Hz. A separate 5 Amp circuit is recommended. A 6-foot grounded cord and plug is included with self-contained models. Plumbing: Self-contained Models: Automatic condensate evaporator is included. No drain connection required. Remote Models: An external drain connection is required. Use the ten foot length of /" ID by 5/8" OD plastic tubing provided to run the drain line for condensate. The tubing should exit through one of the 3/" side knock-out holes. Self-contained Keg Coolers: The drain pain drain is pre-plumbed at the factory to stub out below the compressor compartment. A field connection to an external drain must be made from that point. Uncrating and Start-Up Instructions All models are shipped in one carton. These steps should be followed:. If legs or casters are included, bolt them to the base with the bolts provided.. Unwrap power cord from base if included. 3. Position unit and level and/or seal as required (see page and 3).. The evaporator drain pan on remote models must be plumbed to an external drain. All units with draft beer must be plumbed to an external drain (except model KC which includes an internal plastic drain bottle). On selfcontained models with draft beer and a factory installed finished top, the beer tower drain pan is plumbed through the cabinet and stubs out in the 3" space below the compressor compartment. Connection to an external drain must be made from that point. 5. Place shelves in desired location. 6. Plug into 5 volt AC outlet if a power cord is included. Remote models require electrical connections to be made by an electrician or remote refrigeration contractor. 7. Load with bottles or cans and allow time for products to cool. 8. Your Glastender equipment is now ready for use. Operation The operating temperature range is 36 F ( C) to 0 F (5 C). Self-contained models include an automatic defrost system. The refrigerator will defrost every six hours for approximately 0 minutes. Endwall coolers will defrost every four hours for approximately 5 minutes. During the defrost, the fan inside the cooler will remain on and the refrigeration system will turn off Cleaning Instructions Cleaning is essential to sustaining the integrity of your equipment and preventing corrosion. ESTIMATED CLEANING TIME: 5 to 0 minutes per unit daily, 5 minutes quarterly FREQUENCY: Daily cleaning of exterior & door gaskets. Quarterly cleaning of interior, including shelves. Cleaning Instructions continued on page Fax /

7 Installation Cleaning Instructions continued from page 3 PROCEDURE:. A non-chlorine based cleaner or mild detergent and warm water applied with a soft cloth or sponge to all contact surfaces.. Immediately rinse off cleaning agent(s), using clean warm water, clean soft cloth or sponge. 3. Dry with a soft clean cloth, removing standing water as soon as possible. NOTES:. Never use hydrochloric acid, wire brushes, steel wool, scrapers, or chlorine based cleaners on stainless steel surfaces, since they will break down the passivity layer and allow corrosion to occur.. On stainless steel surfaces, you may use a soft bristle brush or Scotch-Brite pad for more stubborn stains. Always scrub with the direction of the grain. Follow with a thorough cleaning as described above. 3. Deposits from food preparation must be properly removed. Even hard water deposits will rust stainless steel, if not removed.. Repeated cleaning may dry up black-vinyl-clad steel (exterior) surfaces of the cooler. Armor All or similar product can bring back the shine. Apply the product to a cloth and then rub into the surface, rather than spraying it directly onto the black-vinyl-clad surface. 5. The cooler door gaskets are most often overlooked when cleaning. Failure to clean them regularly will lead to premature failure, since alcohol and moisture build-up breaks down the gasket material. Sealing Vertical Door Cooler to Floor To comply with NSF & health codes, the cooler base must be sealed to the floor using NSF listed sealant. Place a bead of sealant along outer edges of the base and remove excess with disposable towel. The floor sealing procedure does not apply to models that include legs or casters. COOLER DOOR MAGNETIC GASKET COOLER CABINET Side View of Cabinet FLOOR BEAD SEALANT " BASE BB Minimum Air Flow Clearance Diagram ARNING: COMPRESSOR FAILURE DUE TO RESTRICTION OR OCKAGE OF AIR FLO ILL VOID ARRANTY. 7" COMPRESSOR COMPARTMENT 8" " 8" " /" MINIMUM CLEARANCE FOR AIR FLO AIR FLO 8 /" 0" SING ILL CONTINUE IF NO CABINET TO IMPEDE Plan View EVAPORATOR HOUSING 80 SING Fax /

8 Installation Attention Installer: ARNING!! Failure to level this cooler ILL VOID THE FACTORY ARRANTY. Doors will not close properly causing damage to hinges, handles, and/or gaskets which will adversely affect the refrigeration systems. COOLER ITH 6" LEGS COOLER ITHOUT LEGS Cooler Installation Checklist Is the unit evenly and solidly supported, either upon legs, or flat on the base; check for high spots? If the unit was designed for legs, are they attached? Is the unit level at the base, from end to end? Do the doors open and close freely, without touching any other part of the unit in travel? Are there open holes to the outside of the cabinet which are not plugged or insulated? Are there obstructions of any kind to air flow into or out of the condensing unit? Is product tubing or are other lines installed in such a manner to not allow shelf access? Special Instructions for Keg Coolers Before you begin:. Disassemble the tower into three parts, stiffener, skin, and top plate, top plate by unscrewing the top two screws.. Mount the column stiffener with provided four /"-0x-/" bolts. 3. Install insulation provided into the bottom of the column stiffener.. Place the column skin over the stiffener. Run the beer lines through the hole at the same time. 5. Install insulation provided into the top of the tower assembly. stiffener skin 6. Mount the column top plate to the column stiffener with the two #0-3x/" phillips flat head s/s machine screws provided. 7. Apply a bead of silicone sealant around the perimeter of the column. Use your finger to smooth out the bead. 8. ash tapping device and faucet with detergent and water. Flush beer tapping device and faucet lines Fax /

9 Cooler Design Change Important Design Change Information In February 00, Glastender released new BB and ND self contained cooler designs with the evaporator housing moved into an area above the compressor compartment. The serial numbers for these units will be and above. As of September 006, KC5, KC7, and KC8 model keg coolers are being manufactured as endwall models. Due to special customer request some BB and ND self contained models may not have the endwall design. Please be sure to verify which cooler design type you are ordering parts for. The term endwall will be used throughout this document to denote parts used for coolers featuring this design. Standard cooler configuration with evaporator inside cooler area. Compressor compartment may be located left or right. Endwall cooler configuration (most BB and ND models manufactured after Feb. 00, most KC models manufactured after Sept. 006) with evaporator located in housing above the compressor compartment. Compressor compartment may be located left or right Fax /

10 Electrical and Refrigeration Specifications BB Self-contained & KC Manufactured After //06 Electrical Refrigerant Pressure P.S.I.G. 5V, phase, 60 Hz Type Charge High Low.0 full load amps, /6 HP R3a 5.0 oz KC Manufactured Before //06 Electrical Refrigerant Pressure P.S.I.G. 5V, phase, 60 Hz Type Charge High Low.8 full load amps, /6 HP R3a 5.0 oz FV, FV8, and BB36 Self-contained Models Manufactured Before /0 Electrical Refrigerant Pressure P.S.I.G. 5V, phase, 60 Hz Type Charge High Low 5. full load amps, /5 HP R 3.5 oz. 85 BB Remote, BB8, BB7, BB96, LP8, LP7, LP96, PT8, PT7, PT96 Electrical Refrigerant Pressure P.S.I.G. 5V, phase, 60 Hz Type Charge High Low R n/a n/a n/a LP60, LP8, LP08 & Non-Endwall BB60, BB8, BB08, KC8, KC7, & KC8 Electrical Refrigerant Pressure P.S.I.G. 5V, phase, 60 Hz Type Charge High Low 8.8 full load amps, /3 HP R 3.5 oz. 85 PT60, PT8 Electrical Refrigerant Pressure P.S.I.G. 5V, phase, 60 Hz Type Charge High Low 8.8 full load amps, /3 HP R0a 9.0 oz. 85 PT08 Electrical Refrigerant Pressure P.S.I.G. 5V, phase, 60 Hz Type Charge High Low 8.8 full load amps, /3 HP R0a 0.0 oz. 85 BB36, BB60, ND5, KC5 Endwall Models Electrical Refrigerant Pressure P.S.I.G. 5V, phase, 60 Hz Type Charge High Low 7. full load amps, /3 HP R3a *.0 oz *.0 oz. charge Serial # F and after. 0.0 oz. charge prior to Serial # F. BB8, BB08, ND7, ND9, KC7, KC8 Endwall Models Electrical Refrigerant Pressure P.S.I.G. 5V, phase, 60 Hz Type Charge High Low 0. full load amps, /3 HP R0a 6.0 oz Fax /

11 iring Diagram for BB36, BB60, ND5, & KC5 Endwall Models HITE LIGHT RECEPTICAL AUX. RECEPTICAL DEFROST TIMER HITE ACK EVAPORATOR FAN 3 ACK LIGHT SITCH UE HITE UE UE MAIN POER SUPPLY CORD ACK HITE GREEN HITE UE 5v AC 5amp CONDENSER FAN ACK ORANGE ACK HITE OVERLOAD COMMON RUN START RELAY STARTER ACK ORANGE THERMOSTAT COMPRESSOR iring Diagram for Models BB8, BB08, ND7, ND9, KC7, & KC8 Endwall Models HITE LIGHT RECEPTICAL AUX. RECEPTICAL DEFROST TIMER ACK HITE EVAPORATOR FAN 3 ACK LIGHT SITCH UE HITE UE UE MAIN POER SUPPLY CORD ACK HITE GREEN HITE UE 5v AC 5amp CONDENSER FAN ACK ORANGE ACK HITE OVERLOAD COMMON RUN START RELAY STARTER ACK ORANGE THERMOSTAT COMPRESSOR Fax /

12 iring Diagram for Self-Contained LP60, LP8, LP08, PT60, PT8, PT08, & Non Endwall BB36, BB60, BB8, BB08, ND5, ND7, ND9, KC8, KC7, KC8* *NOTE: See page 7 for endwall BB, ND, and KC self-contained model wiring diagrams Evaporator Assembly Note: Some Units May Have Two Fans (Three Fans Shown) 3 5 B B S B ITEM 3 DESCRIPTION EVAPORATOR FAN ADE EVAPORATOR FAN MOTOR LIGHT SITCH B 3 B S 5 B CABINET LIGHT RECEPTACLE THERMOSTAT DEFROST TIMER OVERLOAD CAPACITOR COMPRESSOR B 0 START RELAY 5 VOLT 5 AMP SERVICE RECOMMENDED O O CONDENSER FAN MOTOR CONDENSER FAN ADE 3 BALLAST TOMBSTONE 5 STARTER B G G O LEGEND M B = Black = Blue = hite O = Orange G = Green 6 B O G B 7 8 G 9 S C M ELECTRICAL RATINGS All wires are 6 Gauge M 0 Compressor Condenser Fan Motor Evaporator Fan Motor 5V 5V 5V 7.05 AMP.80 AMP.8 AMP(Each) CONDENSING UNIT Fax /

13 iring Diagram for Remote Coolers Including Models BB, BB8, BB7, BB96, LP8, LP7, LP96, PT8, PT7, PT96 Evaporator Assembly Note: Some Units May Have Two Fans (Three Fans Shown) 3 TO LIGHTS ITEM DESCRIPTION O O EVAPORATOR FAN ADE EVAPORATOR FAN MOTOR 3 LIGHT SITCH THERMOSTAT 5 DEFROST TIMER G LEGEND 5V 5 O BK = Black = Blue = hite O = Orange G = Green R = Red Y = Yellow Y/ = Yellow w/blue stripe Y/R = Yellow w/red stripe M O NEUTRAL ELECTRICAL RATINGS All wires are 6 Gauge C REMOTE CONDENSING UNIT Evaporator Fan Motor 5V.8 AMP(Each) O Fax /

14 iring Diagram for Remote Coolers with Solenoid for Installing More than One Unit on One Condensing Unit Evaporator Assembly Note: Some Units May Have Two Fans (Three Fans Shown) 3 TO LIGHTS ITEM DESCRIPTION O O EVAPORATOR FAN ADE EVAPORATOR FAN MOTOR 3 LIGHT SITCH THERMOSTAT 5 DEFROST TIMER G 5V 5 O O S LEGEND BK = Black = Blue = hite O = Orange G = Green R = Red Y = Yellow Y/ = Yellow w/blue stripe Y/R = Yellow w/red stripe M ELECTRICAL RATINGS All wires are 6 Gauge NEUTRAL Evaporator Fan Motor 5V.8 AMP(Each) iring Diagram for Models After /5/00 with Fluorescent Light System FLOURESCENT LIGHT SYSTEM TO LIGHT FLOURESCENT LIGHT SYSTEM ONE LIGHT BK 5V R BALLAST Y/ LIGHT R R 5V B BALLAST STARTER B R B LIGHT R Y/R LIGHT Fax /

15 iring Diagram for BB Self-contained & KC After //06 0 VOLTS POER CORD G M R C OL M THERMOSTAT S START RELAY S COMPRESSOR OVERLOAD CONDENSER FAN MOTOR EVAPORATOR FAN MOTOR ALL IRE 6GA. TOTAL. AMPS KC Before //06 iring Diagram 0 VOLTS POER CORD G FAN TOER COOLING MOTOR O M R C OL THERMOSTAT S START RELAY S COMPRESSOR OVERLOAD ELECTRICAL RATINGS COMPRESSOR,.7 AMPS ALL IRE 6GA Fax /

16 BB Self-contained & KC Compressor, Condenser and Related Parts Part No. Old Part No. Description Price /0 HP Embraco compressor, R3a $ Start capacitor for /0 HP Embraco compressor GT-030 Relay for /6 HP Aspera R3a compressor Relay for /0 HP Embraco compressor GT-0300 Overload protector for /6 HP Aspera R3a compressor Overload protector for /0 HP Embroac compressor GT Automatic defrost timer GT-0353 Condenser fan motor GT-0380 Condenser fan motor blade GT-0335 Beer tower cooling fan shroud (KC models 05/0-0//06) GT-0358 Beer Tower Cooling Fan Motor (KC models 05/0-0//06) GT Exterior blade assembly (KC models 05/0-0//06) GT-0380 Interior blade assembly (KC models 05/0-0//06) GT-0353 Condenser fan motor mounting bracket GT Condenser coil (7" L, 6-7/8" H, -/" ) GT-036 Static condenser coil (KC before 0//06) Filter dryer with service port GT Condensate pan icking material icking Material (KC before 0//06) GT Cap tube 96" X GT-0330 Thermostat with knob and plate [Selco] GT-0389 Knob only Fax /

17 Standard BB36 Compressor and Condenser Related Parts Part No. Old Part No. Description Price GT /5 HP Aspera compressor, R $ GT-030 Start capacitor for /5 HP Aspera R compressor GT-0307 Relay for /5 HP Aspera R compressor GT-030 Overload protector for /5 HP Aspera R compressor GT /5 HP Tecumseh compressor, R (after /00) GT-03 Start capacitor for /5 HP Tecumseh R compressor GT-037 Relay for /5 HP Tecumseh R compressor GT-03 Overload protector for /5 HP Tecumseh R compressor GT Condenser fan motor, GT-0380 Condenser fan motor blade assembly GT-0355 Condenser fan motor mounting bracket GT-0360 Condenser coil (0"L x 7-5/6" x D) GT Fan shroud, condenser Filter dryer with service port GT Condensate pan (3-3/"L x 9-/" x "D) GT-0380 icking material ( required) Elbow, white nylon, /" x /" GT-0376 Tubing, drain, clear plastic, /" ID x 5/8" OD, per foot GT-0353 Base, condensing unit GT Automatic defrost timer, 6hr GT-0300 Condensing unit power cord GT-0377 Cap tube 60" X GT-0350 Accumulator, suction line Fax /

18 Compressor and Condenser Related Parts for LP60, LP8, LP08, & Non Endwall BB60, BB8, BB08, ND5, ND7, ND9, KC7, and KC8 Part No. Old Part No. Description Price GT /3 HP Aspera compressor, R $ GT-030 Start capacitor for /3 Aspera HP R compressor GT-0303 Relay for /3 HP Aspera R compressor GT-030 Overload protector for /3 HP Aspera R compressor GT /3 HP Tecumseh compressor, R (after /00) GT-0306 Start capacitor for /3 HP Tecumseh R compressor GT-03 Relay for /3 HP Tecumseh R compressor GT-0307 Overload protector for /3 HP Tecumseh R compressor GT Condenser fan motor GT-0380 Condenser fan motor blade assembly GT-0355 Condenser fan motor mounting bracket GT-0360 Condenser coil (0"L x 7-5/6" x "D) GT Fan shroud, condenser Filter dryer with service port GT Condensate pan (3-3/"L x 9-/" x "D) GT-0380 icking material ( required) Elbow, white nylon, /" x /" GT-0376 Tubing, drain, clear plastic, /" ID x 5/8" OD, per foot GT-0353 Base, condensing unit GT Automatic defrost timer, 6hr GT-0300 Condensing unit power cord GT-0350 Cap tube 0" X GT-0350 Accumulator, suction line /3 HP, R (BB60, BB8, BB08, ND5, ND7, LP60, LP8, LP08, KC7, KC8) Fax /

19 BB36, BB60, ND5, & KC5* Compressor and Condenser Related Parts for Endwall Models Part No. Old Part No. Description Price GT-0350 /3 HP Tecumseh compressor, R3a $ GT-030 Start capacitor for /3 HP Tecumseh R3a compressor GT-03 Relay for /3 HP Tecumseh R3a compressor GT-03 Overload protector for /3 HP Tecumseh R3a compressor GT-035 Condenser fan motor GT-0380 Condenser fan blade assembly GT-035 Condenser fan motor mounting bracket GT-0360 Condenser coil GT Fan shroud, condenser Filter dryer with service port Condensate pan icking material GT-0373 Tubing, drain, clear plastic, per foot, 3/" ID GT Base, condensing unit GT Automatic defrost timer hr GT-0300 Condensing unit power cord GT Capillary tubing 8" X 0.036" (prior to Serial # F) Capillary tubing 65" X 0.09" (Serial # F and after) GT-0350 Accumulator, suction line 0.00 * KC5 production began with serial number N Fax /

20 BB8, BB08, ND7, ND9, KC7*, & KC8* Compressor and Condenser Related Parts for Endwall Models Part No. Old Part No. Description Price GT /3 HP Embraco compressor, R0a $ GT-0303 Start capacitor for /3 HP Embraco R0a compressor GT-0303 Relay for /3 HP Embraco R0a compressor GT-0305 Overload protector for /3 HP Embraco R0a compressor GT Condenser fan motor GT-0380 Condenser fan blade assembly GT-035 Condenser fan motor mounting bracket GT-0369 Condenser coil GT Fan shroud, condenser Filter dryer with service port Condensate pan icking material GT-0373 Tubing, drain, clear plastic, 3/" dia, per foot GT Base, condensing unit GT Automatic defrost timer hr GT-0300 Condensing unit power cord GT-0380 Cap tube 8" x GT-0350 Accumulator, suction line 0.00 *KC7 Endwall configuration production began with serial number N. *KC8 Endwall configuration production began with serial number 00309N Fax /

21 Compressor and Condenser Related Parts for KC8 Part No. Old Part No. Description Price GT /3 HP Aspera compressor, R $ GT-030 Start capacitor for /3 HP Aspera R compressor GT-0303 Relay for /3 HP Aspera R compressor GT-030 Overload protector for /3 HP Aspera R compressor GT /3 HP Tecumseh compressor, R (same models, after /00) GT-0306 Start capacitor for /3 HP Tecumseh R compressor GT-03 Relay for /3 HP Tecumseh R compressor GT-0307 Overload protector for /3 HP Tecumseh R compressor GT Condenser fan motor, GT Condenser fan blade Condenser fan motor mounting bracket GT-0368 Condenser coil (9"L x 7" x 3-/"D) Fan shroud, condenser (prior to 9/6/06) Housing, condenser fan, 8" models (after 9/6/06) Bracket, condenser fan, top, 8" models (after 9/6/06) Bracket, condenser fan, bottom, 8" models (after 9/6/06) Filter dryer with service port GT-0380 Condensate pan (7-7/8"L x 7-/" x -/"D) icking material Elbow, white nylon, /" x /" GT-0376 Tubing, drain, clear plastic, /" ID x 5/8" OD, per foot GT Automatic defrost timer 6hr GT-0300 Condensing unit power cord GT-0350 Cap tube 0" X GT-0350 Accumulator, suction line Fax /

22 Compressor and Condenser Related Parts for PT60, PT8, and PT08 Part No. Old Part No. Description Price GT /3 HP Aspera compressor, R0a $ GT-0303 Start capacitor for /3 HP Aspera R0a compressor GT-035 Relay for /3 HP Aspera R0a compressor GT-0305 Overload protector for /3 HP Aspera R0a compressor GT /3 HP Tecumseh compressor, R0a (after /00) GT-0306 Start capacitor for /3 HP R0a Tecumseh compressor GT-03 Relay for /3 HP R0a Tecumseh compressor GT-0307 Overload protector for /3 HP R0a Tecumseh compressor GT Condenser fan motor GT-0380 Condenser fan motor blade assembly GT-035 Condenser fan motor mounting bracket GT-0360 Condenser coil (0"L x 7-5/6" x "D) GT Fan shroud, condenser Filter dryer with service port GT Condensate pan (3-3/"L x 9-/" x "D) GT-0380 icking material ( required) Elbow, white nylon, /" x /" GT-0376 Tubing, drain, clear plastic, /" ID x 5/8" OD, per foot GT-0353 Base, condensing unit GT Automatic defrost timer 6hr GT-0300 Condensing unit power cord GT-0350 Cap tube 0" X GT-0350 Accumulator, suction line /3 HP, R0A (PT60, PT8 and PT08) Fax /

23 Compressor and Condenser Related Parts for FV and FV8 Part No. Description Price /5 HP Aspera compressor, R (before 0/00) $ /5 HP Tecumseh compressor, R (after 0/00 and before 0/0/0) Compressor, /hp, 0V, Tecumseh model AEA30YXA (after 0/0/0) Start capacitor for /5HP Aspera R compressor (before 0/00) Start Capacitor, compressor, /hp 3a & /5hp R, 0V 5.00 Tecumseh model AEA30YXA (after 0/00) Relay for /5 HP Aspera R compressor (before 0/00) Relay, compressor, /hp R3a & /5hp R (after 0/00) Overload protector for /5 HP Aspera R compressor (before 0/00) Overload protector, /hp 3a & /5hp R, 0V, Compressor, model 0.00 AEA30YXA & AEA95EXA (after 0/00) Fan shroud, condenser Condenser fan motor, Condenser fan motor blade Condenser fan motor mounting bracket Condenser coil (3"L x 8-/" x -/"D) Filter dryer with service port Condensate pan (7"L x 3-7/8" x -/"D), FV icking material ( required for the FV8) Condensate pan, FV Elbow, white nylon, /" x /" Tubing, drain, clear plastic, /" ID x 5/8" OD, per foot Automatic defrost timer 6hr Condensing unit power cord Cap tube 60" X.036" (before 0/0/0) Cap tube.09", per foot, 0" required (after 0/0/0) Accumulator, suction line Fax /

24 Evaporators and Related Parts Part No. Old Part No. Description Price GT-0330 Expansion valve, remote model, R refrigerant $ GT Expansion valve, remote model, R3a refrigerant GT-033 Expansion valve, remote model, R0a refrigerant GT-0350 Filter dryer for remote coolers GT-0330 Thermostat with knob and plate [Selco] GT-0389 Knob only GT Rope lighting, replacement kit, for BB, BB GT Rope lighting, replacement kit, for BB60, ND8, ND5, LPT GT Rope lighting, replacement kit, for BB8, ND GT Rope lighting, replacement kit, for BB GT Light, fluorescent, plug-in GT Switch (prior to 9/0) GT-033 Switch GT Electrical Outlet, black (Triboro with no ground) GT Receptacle, snap in with ground GT-0308 Solenoid valve, remote cooler GT-0309 Solenoid Coil, 0V, remote cooler GT-0380 Thermometer GT-0395 Light bulb cover. clear plastic Light socket with wire lead, set of GT-0396 Light bulb, GE# F6T GT-0397 Ballast for one light evaporator housing Kit, fluorescent light conversion, replaces single ballast for dual light systems GT-0398 Ballast for two light evaporator housing GT-039 Starter base, fluorescent light GT-039 Starter, fluorescent light, -6-8 watt GT Light bulb, fluorescent, 36" long, T (prior to 08-07) GT-0397 Ballast, 0V, lamp, rapid start (use with ) Bulb, Fluorescent 36", 5 T8 (after 08-07) Ballast, 3 T8 (use with 00036) Lamp holder, Fluorescent light, set of Fax /

25 Evaporators and Related Parts Blower Motor Assembly Endwall BB8, BB08, ND7, ND9, KC5, KC7*, KC8 *KC7 Note: Prior to SN 0373N Mf d Evaporator Coil for BB Self-contained, KC (8" L, -/8" H, 3-/" ) Evaporator Fan Replacement Parts Endwall BB36, BB60, ND5, All Non Endwall Models, and 6 KC7 SN 0373N Mf d --03 and later Evaporator Drain Pan, Left, for Endwall Models BB36, BB60, BB8, BB08, ND5, ND7, ND9, KC5, KC7, and KC8 (9-/8" L, 5" H, /" ) Evaporator Coil for Endwall Models BB36, BB60, BB8, BB08, ND5, ND7, ND9, KC5, KC7, KC8 (6" L, 6" H, " ) Drain Pan for BB Self-contained, KC (8-/" L, 3-7/8" H, " ) Drain Pan Assembly for Non Endwall Models BB8, BB60, BB7, BB8, ND5, ND7, KC8, KC7, KC8 (8-5/8" L, -5/8" H, 3/" ) Evaporator Coil for BB Remote, BB36, LP8, LP60, PT8, FV, FV8 (8-3/" L, -5/8" H, " ) Evaporator Coil for LP7, LP8, LP96, LP08, PT7, PT8, PT96, PT08 (39-/" L, -5/8" H, " ) Drain Pan for BB96, BB08 (39-/" L, -5/8" H, 3/" ) Drain Pan for PT8 (0-3/8" L, -3/" H, " ) Evaporator Coil for Non Endwall Models BB8, BB60, BB7, BB8, ND8, ND0, ND5, ND60 ND7, KC8, KC7, KC8 (7-/" L, " H, -7/8" ) Evaporator Coil for BB96, BB08, ND80 (38-/" L, " H, -7/8" ) Drain Pan for PT7, PT8, PT96, PT08 (-/8" L, -3/" H, " ) Drain Pan for BB Remote, BB36, LP8, LP60 (0-3/8" L, -3/" H, " ) Drain Pan for LP7, LP8, LP96, LP08 (-/8" L, -3/" H, " ) Fax /

26 Evaporators and Related Parts Part No. Old Part No. Description Price GT-0359 Blower motor assembly (Endwall BB8, BB08, ND7, ND9, $5.00 KC5, KC7, KC8) GT-0330 Evaporator fan guard (Endwall BB36, BB60, ND5 & All Non Endwall Models) GT-0380 Evaporator fan motor blade, white plastic (All Non Endwall Models) GT Evaporator fan motor (Endwall BB36, BB60, ND5 & All Non Endwall Models) GT-035 Evaporator fan motor mounting bracket (Endwall BB36, BB60, ND5.00 & All Non Endwall Models) GT Evaporator coil (BB Self-contained, KC) Evaporator coil (Endwall Models BB36, BB60, BB8, BB08, 0.00 ND5, ND7, ND9, KC5, KC7, KC8) (after 3/06) Evaporator coil replacement kit (BB36, BB60, BB8, 0.00 BB08, ND5, ND7, ND9 Endwall Models) (prior to 3/06) It is also necessary to purchase a drain pan, or GT-036 Evaporator coil (BB Remote, BB36, LP8, LP60, PT8, FV, FV8) GT-0368 Evaporator coil (PT60) GT-0363 Evaporator coil (LP7, LP8, LP96, LP08, PT8, PT96, PT08) GT Evaporator coil (Non Endwall Models, BB8, BB60, BB7, BB8, ND0, ND8, ND5, ND60 ND7, KC8, KC7, KC8) GT-0360 Evaporator coil (BB96, BB08, ND80) TXV valve extension Cover (3 door remote coolers) TXV valve extension Cover ( door remote coolers) TXV valve Cover (all remote coolers) GT Evaporator drain pan (BB Self-contained, KC) Evaporator drain pan (KC) (prior to 0//06) Evaporator drain pan, Right (Endwall Models BB36, BB60, BB8, BB08, ND5, ND7, ND9, KC5, KC7, KC8) (after 3/06) Evaporator drain pan, Left (Endwall Models BB36, BB60, BB8, BB08, ND5, ND7, ND9, KC5, KC7, KC8) (after 3/06) GT Evaporator drain pan (Endwall Models BB36, BB60, BB8, BB08, ND5, ND7, ND9) (prior to 3/06) Drain pan assembly, evaporator, fan, remote (Non Endwall Models, 5.00 BB8, BB60, BB7, BB8, ND5, ND7, KC8, KC7, KC8) GT Evaporator drain pan (BB96, BB08) Evaporator drain pan (PT60) Evaporator drain pan (PT8) GT Evaporator drain pan (PT7, PT8, PT96, PT08) GT Evaporator drain pan (BB Remote, BB36, LP8, LP60) GT Evaporator drain pan (LP7, LP8, LP96, LP08) Evaporator drain pan (FV, FV8) Assembly, shroud, evaporator, -fan, - door e/w, 0 Volt Assembly, shroud, evaporator, -fan, - door e/w, 0 Volt, digital t-stat Fax /

27 Doors and Related Parts Part No. Old Part No. Description Price GT-0350 Door handle, stainless $ GT-0350 Door handle, brass Door handle, tab style, glass door, right (Prior to 003) Door handle, tab style, glass door, left (Prior to 003) GT Door lock, stainless Key, #806, for stainless cooler door lock ( ) GT Door lock, brass Key, #606, for brass cooler door lock ( ) GT Plug for door handle, stainless GT Plug for door handle, brass GT Screws for top of handle, stainless (set of ), 0/3 x " PFH Machine Screw GT Screws for top of handle, brass (set of ), 0/3 x 5/8" PFH Machine Screw GT Screw for bottom of handle, stainless, and screws for old style brackets GT Screw for bottom of handle, black GT-03 Hinge set, 0º swing, set of two w/screws and washers GT-030 Hinge set, 80º swing, set of two (prior to /99 - w/ screws and washers) GT-035 Hinge bracket, bottom, left (prior to /99 - w/ screws) GT-036 Hinge bracket, bottom, right (prior to /99 - w/ screws) GT-030 Hinge set and brackets, 80º swing, left (complete with screws) GT-03 Hinge set and brackets, 80º swing, right (complete with screws) GT-0353 Lock bracket GT-0330 Hinge set & brackets for wood doors, 80º swing, left (complete with screws) GT-033 Hinge set & brackets for wood doors, 80º swing, right (complete with screws) GT-0335 Lock bracket for wood doors GT Cooler door gasket, push-in style, black, 3-/" x 3-/" OD GT Cooler door gasket, screw-on style (wooden doors before 6/9/90) 3½" x 3½" OD GT-0337 Cooler door gasket, LP and FV models, black, 3½" x 6½" OD GT-0333 Cooler door gasket, narrow door, black, 9½" x 3½" OD GT Screw for door hinges ( required) GT Bolts for brackets (6 required) Hinge rail, bottom, front vent coolers ( washers required, not 0.00 included) GT-0360 Plastic washer for hinge GT Bushing for hinge (gray) Standard laminated door trim rail kit Laminated door trim rail kit, for narrow doors Laminated door trim rail kit, for low profile narrow doors Laminated door trim rail kit, for low profile doors Fax /

28 Doors and Related Parts Replacement Doors for Units Manufactured PRIOR to January 999 Replacement Doors for BB, PT, RF, DS, KC7, and KC8 Models Part No. Old Part No. Description Price GT Black vinyl clad door (prior to /99) $ GT Unlaminated door (prior to /99) GT Laminated door (prior to /99) GT Stainless door (prior to /99) Glass door, black (prior to /99) Glass door, stainless (prior to /99) Replacement Doors for LP and FV Models GT Black vinyl clad door, low profile (prior to /99) GT Unlaminated door, low profile (prior to /99) GT Laminated door, low profile (prior to /99) GT Stainless door, low profile (prior to /99) Glass door, low profile, black (prior to /99) Glass door, low profile, stainless (prior to /99) Replacement Doors for ND Models GT Black vinyl clad door, narrow (prior to /99) GT-0367 Unlaminated door, narrow (prior to /99) GT Laminated door, narrow (prior to /99) GT Stainless door, narrow (prior to /99) Glass door, narrow, black (prior to /99) Glass door, narrow, stainless (prior to /99) NOTE: Door gaskets, handles and hinges are sold separately, see page 6 for part numbers Fax /

29 Doors and Related Parts Replacement Doors for Units Manufactured January 999 and After Replacement Doors for BB, PT, RF, DS, and KC Models Part No. Old Part No. Description Price GT Black vinyl clad door $ GT-0368 Unlaminated door GT-0368 Laminated door GT Stainless door Glass door, black Glass door, stainless Replacement Doors for LP and FV Models GT Black vinyl clad door, low profile GT Unlaminated door, low profile GT Laminated door, low profile GT Stainless door, low profile Glass door, low profile, black Glass door, low profile, stainless Replacement Doors for ND Models GT-0369 Black vinyl clad door, narrow GT Unlaminated door, narrow GT-0369 Laminated door, narrow GT Stainless door, narrow Glass door, narrow, black Glass door, narrow, stainless NOTE: Door gaskets, handles and hinges are sold separately, see page 6 for part numbers 3 /6 3 /6 3 5 /8 9 /6 3 /6 7 /6 7 ½ 3 / Fax /

30 Doors and Related Parts Replacement Glass Doors for Units Manufactured September 003 and After NOTICE: In September of 003, we released new style glass doors for our vertical door coolers. These new style doors fit all of our units manufactured AFTER January 999, However these new style glass doors look different than the glass doors manufactured BETEEN January 999 and September 003. Please consider this fact if you need to match the look of your replacement glass door with that of existing glass doors. If you need to order the style of glass doors manufactured between January 999 and September 003, please refer to page 5. Replacement Doors for BB, PT, RF, DS, and KC Models Part No. Old Part No. Description Price GT-0000 Stainless Steel Glass Door $ GT-000 Black Vinyl Clad Glass Door GT-000 Laminated Glass Door Replacement Doors for LP and FV Models Part No. Old Part No. Description Price GT-000 Stainless Steel Glass Door GT-00 Black Vinyl Clad Glass Door GT-00 Laminated Glass Door Replacement Doors for ND Models Part No. Old Part No. Description Price GT-000 Stainless Steel Glass Door GT-00 Black Vinyl Clad Glass Door GT-00 Laminated Glass Door NOTE: Door gaskets, handles, and hinges are sold separately, see page 6 for part numbers 3 5/8" 9 5/8" 3 5/8" 33 3/8" 7 /" 33 3/8" Fax /