65A PARTS MANUAL. Backhoe RHINO

Transcription

1 65A Backhoe Published 10/01 Part No. F A An Operator s Manual was shipped with the equipment in the Manual Canister. The Operator s Manual is an integral part of the safe operation of this machine and must be maintained with the unit at all times. READ, UNDERSTAND, and FOLLOW the Safety and Operation Instructions contained in the Operator s Manual before operating the equipment. If the Operator s Manual is not with the equipment, contact your dealer or Rhino ( ) to obtain a Free copy before operating the equipment. PARTS MANUAL RHINO 1020 S. Sangamon Ave. Gibson City, IL parts@servis-rhino.com 2001 Alamo Group, Inc.

2 TO THE OWNER/OPERATOR/DEALER All implements with moving parts are potentially hazardous. There is no substitute for a cautious, safe-minded operator who recognizes the potential hazards and follows reasonable safety practices. The manufacturer has designed this implement to be used with all its safety equipment properly attached to minimize the chance of accidents. BEFORE YOU START!! Read the safety messages on the implement and shown in your manual. Observe the rules of safety and common sense! SAFETY HAZARD SIGNAL WORDS There are three levels of hazard intensity identified by signal words DANGER, WARNING and CAUTION. The level of hazard intensity is identified by the following definitions. DANGER DANGER - Immediate hazards which will result in severe injury or death. WARNING WARNING - Hazards or unsafe practices which could result in minor personal injury or death. CAUTION CAUTION - Hazards or unsafe practices which could result in minor personal injury or property damage. THIS SAFETY SYMBOL MEANS ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! PELIGRO LEA EL INSTRUCTIVO Si No Lee Ingles, Pida Ayuda a Alguien Que Si Lo Lea Que le Traduzca las Medidas de Seguridad. Read and understand the complete Warranty Statement found in this Manual. Fill out the Warranty Registration Form in full and return it within 30 Days. Make certain the Serial Number of the Machine is recorded on the Warranty Card and on the Warranty Form that you retain. The use of will-fit parts will void your warranty and can cause catastrophic failure with possible injury or death.

3 SAFETY DECALS SAFETY DECALS NOTE: Safety decal location is listed below each decal. Replace decal if damaged or illegible. Replacement decals are available from your dealer i

4 SAFETY DECALS LEFT SIDE - BOOM RIGHT SIDE - BOOM SAFETY DECALS LEFT SIDE RIGHT SIDE 5 REAR VIEW TOP VIEW - LEFT STABILIZER TOP VIEW - RIGHT STABILIZER TOP VIEW - COVER PLATE ii

5 SAFETY DECALS SAFETY DECALS iii

6 SAFETY DECALS SAFETY DECALS ITEM PART NO. QTY. TYPE DESCRIPTION OPERATION Right Side Stabilizer Position WARNING To Prevent Bodily Injury WARNING To Prevent Bodily Injury DANGER Crushing Hazard DANGER Crushing Hazard OPERATION Left Side Stabilizer Position WARNING To Prevent Instability OPERATION Dipperstick & Bucket Operation OPERATION Boom Operation LOGO Rhino Universal One Call OPERATION Swing Lock OPERATION Boom Lock LOGO Rhino NAME 65A INSTRUCT Operator's Manual Inside iiii

7 Parts 1

8 PARTS ORDERING GUIDE The following instructions are offered to help eliminate the needless delay and error in processing purchase orders for the equipment in this section 1. The Parts Section is prepared in logical sequence and grouping of parts that belong to the basic machine featured in this manual. Part Numbers and Descriptions are given to help locate the parts and quantities required. 2. The Purchase Order must include name and address of the person or organization ordering the parts, who should be charged, and if possible, the serial number of the machine for which the parts are ordered. 3. The Purchase Order must clearly list the quantity of each part, the complete and correct part number, and the basic name of the part. 4. The Manufacturer reserves the right to substitute parts where applicable. 5. Some parts are unlisted items which are special production items not normally stocked and are subject to special handling. Request a quotation for such parts before sending a Purchase Order. 6. The Manufacturer reserves the right to change prices without notice. NOTE: Please refer to The Safety Section in the front of this Manual for the proper Part Number when ordering Replacement Safety Decals. For maximum safety and to guarantee optimum product reliability, always use genuine Rhino Parts. The use of inferior replacement parts may cause premature or catastrophic failure which could result in serious injury or death. Direct any questions regarding parts to an authorized Rhino Dealer. qqqqqqqqqq For dealer location information contact: Rhino 1020 S. Sangamon Ave. Gibson City, IL Parts@servis-rhino.com F Parts 2

9 TABLE OF CONTENTS Boom Assembly Buckets Cylinder Assembly - Boom & Dipper Cylinder Assembly - Bucket Cylinder Assembly - Swing Dipperstick & Bucket Assembly Hydraulic Hose Schematic Mainframe Assembly Seat Assembly Swing Frame Assembly Valve Assembly F Parts 3

10 MAINFRAME ASSEMBLY F Parts 4

11 MAINFRAME ASSEMBLY ITEM PART NO. QTY. DESCRIPTION CYLINDER, Stabilizer STABILIZER PAD STABILIZER, Assembly PIN, Anti Rotation, 1-x 5-7/ TRIM, Plastic, 8.5" SUPPORT, Swing Cylinder PIN, 1 x MAINFRAME BUSHING, 1.00 I.D. X 1.25 O.D. X 1.25 Long PIN, 1 x BUSHING, 1.88 O.D. x 1.50 I.D. X 1.00 Long COTTER, Hair Pin, 3/32 x 1-7/ PIN, Stop, Stabilizer Pad FITTING, Grease, 1/ C 4 NUT, Lock, 5/ COTTER PIN, 3/16 x 1-1/ RUBBER BUMPER DECAL, Operation C 10 WASHER, Flat, 5/ WASHER, Lock, 5/ SCREW, Cap, 5/16-18 x 3/ H8C 4 SCREW, Cap, 5/8-11 x 2-1/ C 4 NUT, Lock, 5/ SHOULDER BOLT, 3/8-16 x NUT, Lock, 3/ DECAL, Swing Lock COVER, Plate WASHER, Machine, 1 x 1-1/ COVER, Seat Bracket SPEED NUT, Clip On ANTI SKID PATCH DECAL, Warning, Bodily Injury DECAL, Warning, Bodily Injury DECAL, Danger, Crushing, Hazard DECAL, Danger, Crushing Hazard DECAL, Operation DECAL, Warning, Prevent Instability DECAL, Operation DECAL, Operation DECAL, Rhino DECAL, Universal One Call F Parts 5

12 SWING FRAME ASSEMBLY ITEM PART NO. QTY. DESCRIPTION CYLINDER, Swing PLATE, Orifice SWING BRACKET PIN, Swing Cylinder, 1 x 4-3/ WASHER, Thrust 1-1/2 ID x 2-1/4 OD x.09 Thickness H5C 2 SCREW, Cap, 5/16-18 x C 6 NUT, Lock, 5/ PIN, Swing Post, 1-1/2 x U-BOLT, 5/ NUT, Lock, 3/ FITTING, Grease, 1/ LOCK, Flat BUSHING, Machine, 1 inch I.D COTTER PIN, 5/16 x 2-1/ PIN, Boom Cylinder Rod, 1 x 7-1/ SCREW, Cap, 3/8-16 x 2-1/ PIN, Boom Base 1-1/4 x 7-1/ FITTING, Grease, 1/8 NPT BUSHING, Sleeve, 1.00 I.D. x 1.25 O.D. X 1.00 Long PIN, Swing Lock, 3/4 x 3 Clevis HAIR PIN COTTER F Parts 6

13 BOOM ASSEMBLY 65A ITEM PART NO. QTY. DESCRIPTION BOOM CYLINDER, Dipperstick CYLINDER, Boom PIN, Dipper Stick Base, 1x PIN, Lift Cylinder, Base 1x SHOULDER BOLT, 3/8-16 x PLATE, Orifice DECAL, Boom Lock FITTING, Grease, 1/ NUT, Lock, 3/ H5C 1 SCREW, Cap, 5/16-18 x C 2 NUT, Lock, 5/ FITTING, Grease, 1/8 NPT SPEED NUT CLAMP, Hose SCREW, Cap, 5/16-18 x 1-1/ WASHER, Lock, 5/ CLAMP SCREW, Cap, 3/8-16 x 1-1/ DECAL, RHINO DECAL, Model 65A, White GROMMET GROMMET C 1 WASHER, Flat, 5/16 SAE F Parts 7

14 DIPPERSTICK & BUCKET ASSEMBLY F Parts 8

15 DIPPERSTICK & BUCKET ASSEMBLY ITEM PART NO. QTY. DESCRIPTION CYLINDER, Bucket 2 * - BUCKET, Complete, 9" ( ) * - BUCKET, Complete, 12" ( ) * - BUCKET, Complete, 12" Heavy Duty ( ) * - BUCKET, Complete, 16" ( ) * - BUCKET, Complete, 16" Heavy Duty ( ) * - BUCKET, Complete, 18" ( ) DIPPERSTICK TOGGLE LINK PLATE, Link, Arm, Toggle PIN, Anti Rotation, 1 x 6-5/ PIN, Cylinder Base, 1 x 6-1/ FITTING, Grease, 1/ SOCKET, Slow Moving Vehicle BRACKET, Mounting, Slow Moving Vehicle C 2 BOLT, Carriage, 5/16-18 x 3/ C 6 NUT, Lock, 5/ CLAMP, Hose, # PIN, 1 x 7-1/ SCREW, Cap, 3/8-16 x 2-1/ SCREW, Cap, 3/8-16 x 1-1/ TOOTH, Bucket, 1-3/4 Wide SHANK, Bucket, 1" Wide H5C 2 SCREW, Cap, 5/16-18 x COTTER PIN, 1/4 x 1-1/ LINK, Bucket C 2 NUT, Jam, 3/ B600 2 WASHER, Flat, 3/ NUT, Lock, 3/ PIN, Pivot, 1-1/4 x 7-1/ WASHER, Machine, 1 x 1-1/ BUSHING, 1.00 I.D. x 1.25 O.D. X 1.50 Long PIN, 1 x 8-1/8 * Buckets not sold as repair part (order as whole goods) F Parts 9

16 HYDRAULIC SCHEMATIC 19 F Parts 10

17 HYDRAULIC SCHEMATIC ITEM PART NO. QTY. DESCRIPTION FITTING, Elbow, 9/16-18 JIC x 3/4 O-Ring, VALVE PLATE, Orifice FITTING, Adapter, HOSE, 1/4 x 16 (Swing Cylinder to Swing Cylinder) FITTING, Adapter, 3/4 O-Ring x 9/16 JIC FITTING, Elbow, 9/16-18 JIC x 9/16-18 JIC Swivel, HOSE, 1/4 x 124 (Dipper & Bucket Rod) HOSE, 1/4 x 108 (Dipper & Bucket Base) HOSE, 1/4 x 54 (Stabilizer to Valve) FITTING, Elbow, 3/4-16 JIC x 3/4-16 O-Ring, HOSE, 1/4 x 40 (Swing Cylinder to Valve) NYLON SLEEVE, 6" HOSE, 1/4 x HOSE CLAMP TIE STRAP, Adjustable, 1/2 x TIE STRAP, Adjustable, 3/16 x WOVEN COTTON LOOM NYLON SLEEVE, NYLON SLEEVE, NYLON SLEEVE, HOSE, 1/4 x 102 (Dipper Cylinder Base and Rod) F Parts 11

18 SEAT ASSEMBLY ITEM PART NO. QTY. DESCRIPTION SEAT PLATE, Seat C 1 NUT, Lock, 1/ POST, Seat SCREW, Cap, 3/8-16 x 1-1/ NUT, Lock, 3/ COTTER PIN, 3/16 x 3/ SCREW, Cap, 5/16-18 x 3/ SCREW, Cap, 1/2-13 x 3-1/ BOLT, Shoulder, 3/8-16 x 1-1/ WASHER, Lock, 5/ LATCH, Spacer SPRING C 2 TOP LOCK NUT, 1/ WASHER, Flat, 1/ SCREW, Cap, 1/4-20 x DECAL, Manual Canister CANISTER,with Cap (Includes item 19) SEAL, Manual Canister MOUNTING PLATE, Canister F Parts 12

19 CYLINDER ASSEMBLY- SWING NOTE: Cylinder code stamped near cylinder base end. SWING CYLINDER (2-1/4 ) ITEM PART NO. QTY. DESCRIPTION ROD, 1-3/8" 2 * 1 RING, Wiper 3 * 1 SEAL, V-Cup 4 * 1 RING, Backup 5 * 1 O-Ring HEAD, Cylinder 7 * 1 RING, Wear PISTON 9 * 2 O-Ring 10 * 1 SEAL, Piston 11 * 1 RING, Wear RING, Steel NUT, Lock, CYLINDER TUBE 15 * 1 LOCKWIRE BUSHING, 1.00 I.D. x 1.25 O.D. X 1.00 Long * Repair Kit, Includes (*) Items F Parts 13

20 CYLINDER ASSEMBLY- BUCKET NOTE: Cylinder code stamped near cylinder base end. BUCKET CYLINDER (2-1/4 ) STABILIZER CYLINDER (2-1/4 ) ITEM PART NO. QTY. DESCRIPTION ROD, 1-3/8" (Bucket Cylinder) ROD, 1-3/8" (Stabilizer Cylinder) 2 * 1 RING, Wiper 3 * 1 SEAL, V-Cup 4 * 1 RING, Backup 5 * 1 O-Ring HEAD, Cylinder 7 * 1 RING, Wear PISTON 9 * 2 O-Ring 10 * 1 SEAL, Piston 11 * 1 RING, Wear NUT, Lock, 3/ CYLINDER TUBE, (Bucket Cylinder) CYLINDER TUBE, (Stabilizer Cylinder) 14 * 1 LOCKWIRE * Repair Kit, Includes (*) Items F Parts 14

21 CYLINDER ASSEMBLY- BOOM & DIPPER NOTE: Cylinder code stamped near cylinder base end. BOOM CYLINDER (2-1/2 ) ITEM PART NO. QTY. DESCRIPTION ROD, 1-3/8" 2 * 1 RING, Wiper 3 * 1 SEAL, V-Cup 4 * 1 RING, Backup 5 * 1 O-Ring HEAD, Cylinder 7 * 1 RING, Wear PISTON 9 * 2 O-Ring 10 * 1 SEAL, Piston 11 * 1 RING, Wear NUT, Flange Lock, 3/ CYLINDER TUBE 14 * 1 LOCKWIRE * Repair Kit, Includes (*) Items DIPPER CYLINDER (2-1/4 ) ITEM PART NO. QTY. DESCRIPTION ROD, 1-3/8" 2 * 1 RING, Wiper 3 * 1 SEAL, V-Cup 4 * 1 RING, Backup 5 * 1 O-Ring HEAD, Cylinder 7 * 1 RING, Wear PISTON 9 * 2 O-Ring 10 * 1 SEAL, Piston 11 * 1 RING, Wear NUT, Lock, 3/ CYLINDER TUBE 14 * 1 LOCKWIRE * Repair Kit, Includes (*) Items F Parts -15

22 VALVE ASSEMBLY There are two different styles of working sections Order positioner kits (2 & 5) for your style of valve Top View Shown Old Style A Spool New Style B NOTE: Use loctite 262 when replacing spool ends (35). F Parts 16

23 VALVE ASSEMBLY REPAIR PARTS - (45882) ITEM PART NO. QTY. DESCRIPTION SEAL KIT, Main Relief Cartridge SPRING CENTER POSITIONER KIT (Old Style A ) SPRING CENTER POSITIONER KIT (New Style B ) SEAL KIT, Body Section PLUG, Port FLOAT POSITIONER KIT (Old Style A ) FLOAT POSITIONER KIT (New Style B ) RISER, Right RISER, Left (Not Shown) HANDLE KNOB H8C 6 SCREW, Cap, Socket Head, 1/4-28 x 3/ ROD END, Assembly ROD END H8C 2 SCREW, Cap, 1/4-20 x 2, Grade H8C 8 SCREW, Cap, Socket Head, #10-24 x 1-1/ NUT, Hex, 1/ RELIEF, Work Port, 2500 PSI RELIEF, Work Port with Anti Cavitation, 2150 PSI RELIEF, Main 2150 PSI C 2 NUT, Lock, 1/ STUD KIT (Includes 4 stud bolts) SEAL KIT, Relief (Work relief cartridges) PLUG, No Relief Cavity SEAL KIT, Spool (Includes 2 Seals) Mounting Bracket POWER BEYOND SLEEVE (Optional) PLUG KIT, Load Check BOOT SEAL KIT, Power Beyond SCREW, Cap, 5/16-18 x C 4 WASHER, Flat, 5/ C 4 NUT, Lock, 5/ SEAL KIT, Work Port Plug NUT, Hex, 1/ HANDLE KIT (Includes items 41-46) CLEVIS & PIN KIT INLET COVER OUTLET COVER VALVE SECTION, 4-Way, 3-Position (Does not include items 16, 17, 19, 34 or 35) VALVE SECTION, 4-Position Float (Does not include item 19) VALVE SECTION, with long spool (Does not include 16 or 17) H8C 4 SCREW, Cap, Socket Head, #10-24 x BRACKET, Handle KNOB, Handle ROD, Handle BOOT, Dust PIN, Dowel, 3/16 x.50 F Parts 17

24 BUCKETS Standard Buckets Heavy Duty Buckets BUCKET BUCKET WIDTH STRUCK CAPACITY MODEL Inches Cubic Feet 9" " " H.D " " H.D " ITEM PART NO. QTY. DESCRIPTION BUCKET, 9" - - BUCKET, 12" - - BUCKET, 12" H.D. - - BUCKET, 16" - - BUCKET, 16" H.D. - - BUCKET, 18" TOOTH, Bucket SHANK, Bucket SCREW, Cap, 3/8-16 x 1-1/4 (Standard buckets only) C 2 NUT, Jam, 3/8-16 (Standard buckets only) PIN, 1 x 8-1/2 (Heavy Duty buckets only) H5C 2 SCREW, Cap, 5/16-18 x 2 (Heavy Duty buckets only) C 2 NUT, Lock, 5/16-18 (Heavy Duty buckets only) F Parts 18

25 NUMERICAL PART INDEX Part No. Page No. Part No. Page No. Part No. Page No , , , , ,6,7,9, , 6, 7, , 9, 12, , , 6, 9 15B H8C H5C , 7, 9, , H8C H8C H8C H8C C , C ,6,7, ,17, C C C , , C C , 7, , 14, , 14, , , , F Parts 19

26 NUMERICAL PART INDEX Part No. Page No. Part No. Page No. Part No. Page No , , 7, , , , F Parts 20

27 RHINO LIMITED WARRANTY 1. LIMITED WARRANTIES Rhino warrants for one year from the purchase date to the original non-commercial, governmental, or municipal purchaser ( Purchaser ) and warrants for six months to the original commercial or industrial purchaser ( Purchaser ) that the goods purchased are free from defects in material or workmanship Manufacturer will replace for the Purchaser any part or parts found, upon examination at one of its factories, to be defective under normal use and service due to defects in material or workmanship This limited warranty does not apply to any part of the goods which has been subjected to improper or abnormal use, negligence, alteration, modification, or accident, damaged due to lack of maintenance or use of wrong fuel, oil, or lubricants, or which has served its normal life. This limited warranty does not apply to any part of any internal combustion engine, or expendable items such as blades, shields, guards, or pneumatic tires except as specifically found in your Operator s Manual Except as provided herein, no employee, agent, Dealer, or other person is authorized to give any warranties of any nature on behalf of Manufacturer. 2. REMEDIES AND PROCEDURES This limited warranty is not effective unless the Purchaser returns the Registration and Warranty Form to Manufacturer within 30 days of purchase Purchaser claims must be made in writing to the Authorized Dealer ( Dealer ) from whom Purchaser purchased the goods or an approved Authorized Dealer ( Dealer ) within 30 days after Purchaser learns of the facts on which the claim is based Purchaser is responsible for returning the goods in question to the Dealer It after examining the goods and/or parts in question, Manufacturer finds them to be defective under normal use and service due to defects in material or workmanship, Manufacturer will: (a) Repair or replace the defective goods or part(s) or (b) Reimburse Purchaser for the cost of the part(s) and reasonable labor charges (as determined by Manufacturer) if Purchaser paid for the repair and/or replacement prior to the final determination of applicability of the warranty by Manufacturer. The choice of remedy shall belong to Manufacturer Purchaser is responsible for any labor charges exceeding a reasonable amount as determined by Manufacturer and for returning the goods to the Dealer, whether or not the claim is approved. Purchaser is responsible for the transportation cost for the goods or part(s) from the Dealer to the designated factory. 3. LIMITATION OF LIABILITY MANUFACTURER DISCLAIMS ANY EXPRESS (EXCEPT AS SET FORTH HEREIN) AND IMPLIED WARRANTIES WITH RESPECT TO THE GOODS INCLUDING, BUT NOT LIMITED TO, MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE MANUFACTURER MAKES NO WARRANTY AS TO THE DESIGN, CAPABILITY, CAPACITY, OR SUITABILITY FOR USE OF THE GOODS EXCEPT AS PROVIDED HEREIN, MANUFACTURER SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO PURCHASER OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY LIABILITY, LOSS, OR DAMAGE CAUSED OR ALLEGED TO BE CAUSED DIRECTLY OR INDIRECTLY BY THE GOODS INCLUDING, BUT NOT LIMITED TO, ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES RESULTING FROM THE USE OR OPERATION OF THE GOODS OR ANY BREACH OF THIS WARRANTY. NOT WITHSTANDING THE ABOVE LIMITATIONS AND WARRANTIES, MANUFACTURERS LIABILITY HEREUNDER FOR DAMAGES INCURRED BY PURCHASER OR OTHERS SHALL NOT EXCEED THE PRICE OF THE GOODS NO ACTION ARISING OUT OF ANY CLAIMED BREACH OF THIS WARRANTY OR TRANSACTIONS UNDER THIS WARRANTY MAY BE BROUGHT MORE THAN TWO (2) YEARS AFTER THE CAUSE OF ACTION HAS OCCURRED. 4. MISCELLANEOUS Proper Venue for any lawsuits arising from or related to this limited warranty shall be only in Guadalupe County,Texas Manufacturer may waive compliance with any of the terms of this limited warranty, but no waiver of any terms shall be deemed to be a waiver of any other term If any provision of this limited warranty shall violate any applicable law and is held to be unenforceable, then the invalidity of such provision shall not invalidate any other provisions herein Applicable law may provide rights and benefits to purchaser in addition to those provided herein. KEEP FOR YOUR RECORDS ATTENTION: Purchaser should fill in the blanks below for his reference when buying repair parts and/or for proper machine identification when applying for warranty. Rhino Implement Model Serial Number Date Purchased Dealer ATTENTION: READ YOUR OPERATORS MANUAL RHINO Member of the Alamo Group 1020 S. Sangamon Ave. Gibson City, IL

28 TO THE OWNER/OPERATOR/DEALER In addition to the standard Limited Warranty shown on the facing page, Rhino also provides: 1. A TWO-YEAR (24 months) LIMITED WARRANTY* on non-perishable structural items such as: Loader Boom, Side Frames, Mount Brackets, Backhoe Boom, Dipper, Main Frame, Stabilizer Legs, Swing Bracket, Subframe and Related Mounting Brackets provided they have not been subjected to abuse or mis- use and have been properly maintained as noted. NOTE properly maintained specifically includes, but is not limited to: A) Regular lubrication. B) Using proper amounts of correct hydraulic fluid. C) Regular torque inspection of all fasteners. 2. *WARRANTY LIMITATIONS Warranty is ONE-YEAR (12 months) for hydraulic cylinders and seals, pivot pins, wear bushings, hydraulic hoses, buckets or other attachments, wear or cutting edges and tooth bars. After one year (12 months) standard warranty, these items are considered Wearing Perishable Parts and replacement is the users responsibility.

29 TO THE OWNER/OPERATOR/DEALER To keep your implement running efficiently and safely, read your manual thoroughly and follow these directions and the Safety Messages in this Manual. The Table of Contents clearly identifies each section where you can easily find the information you need. The OCCUPATIONAL SAFETY AND HEALTH ACT ( Subpart C) makes these minimum safety requirements of tractor operators: REQUIRED OF THE OWNER: 1. Provide a Roll-Over-Protective Structure that meets the requirements of this Standard; and 2. Provide Seatbelts that meet the requirements of this paragraph of this Standard and SAE J4C; and 3. Ensure that each employee uses such Seatbelt while the tractor is moving; and 4. Ensure that each employee tightens the Seatbelt sufficiently to confine the employee to the protected area provided by the ROPS. REQUIRED OF THE OPERATOR 1. Securely fasten seatbelt if the tractor has a ROPS. 2. Where possible, avoid operating the tractor near ditches, embankments, and holes. 3. Reduce speed when turning, crossing slopes, and on rough, slick, or muddy surfaces. 4. Stay off slopes too steep for safe operation. 5. Watch where you are going - especially at row ends, on roads, and around trees. 6. Do not permit others to ride. 7. Operate the tractor smoothly - no jerky turns, starts, or stops. 8. Hitch only to the drawbar and hitch points recommended by the tractor manufacturer. 9. When the tractor is stopped, set brakes securely and use park lock, if available. Keep children away from danger all day, every day... Equip tractors with rollover protection (ROPS) and keep all machinery guards in place... Please work, drive, play and live each day with care and concern for your safety and that of your family and fellow citizens

30 65A-OMWPL Printed U.S.A. P/N F-3631