How To Power A Bladecenter H Servers

Transcription

1 Solutions Guide for IBM Data Center Architecture: IBM BladeCenter H Servers In today s high-demand enterprise environment, organizations need a reliable infrastructure to run compute-intensive applications with minimal maintenance and downtime. IBM BladeCenter H is a powerful platform built with the enterprise customer in mind, providing industry-leading performance, innovative architecture and a solid foundation for virtualization. Blade server applications present unique challenges in terms of rack level power distribution (ack PDU), cable management and physical access space requirements for hot-swappable blade components. This application guide provides recommendations for enclosures, ack PDUs, and cable management to best address the specific physical infrastructure needs of the BladeCenter H Chassis.

2 Contents Instructions.. 4 ack PDU selection.5 Additional ack PDU.. 7 Enclosure Diagrams..9 Cable Management 12 2

3 Enclosures and ack Mount Power Distributions Units Advanced PDUs Integrates power management capabilities with other products including Symmetra PX UPS, row and room PDUs, Inow cooling, NetShelter SX enclosures, and StruxureWare for Data Centers management software suite. Features zero U, low profile design, optimized for high-density rack power solutions to minimize interference between the ack PDU and hot-swap blade components. Comprehensive device, phase, and breaker bank level metering for overload protection, capacity planning purposes, and energy efficiency initiatives ight Angle C19/C20 connectors minimize bend radius at the connection point and reduce interference in the rear of an enclosure Full Featured Enclosures NetShelter SX enclosures offer the most standard, outof-box features to ease installation and speed deployment. Single enclosure design is flexible enough to accommodate various networking and server applications. Sizes Available: 42U, 45U, & 48U heights, 600mm (24 ) & 750mm (30 ) widths, and 1070mm (42 ) & 1200mm (47.2 ) depths. Schneider Electric is a global leader in data center infrastructure - cooling, UPS, power distribution, racks and management. 3

4 Instructions This guide is designed to facilitate a step by step selection of ack PDUs, enclosures and accessories for IBM BladeCenter H servers. STEP 1: Determine estimated power load per blade chassis. After consulting the manual, determine the total power load and redundancy configurations offered. BladeCenter H includes options for up to four standard 2900 W or 2980W highefficiency hot-swap and redundant load-balancing power supplies. At full redundancy, the chassis is capable of maximum input power capacity over 7000W. Total max power consumption for a typical customer configuration of BladeCenter H chassis is 5kW. The average power is about 3-4kW. STEP 2: Table 3A, 3B: Maximum Quantity Chassis per ack PDU. Table is organized by maximum capacity of standard 20A, 30A, 50A, and 60A ack PDUs kw. Utilize power data calculated in step 1 and required number of connected servers to select the proper capacity ack PDU. STEP 3: Table 3A, 3B: Select ack PDU. Take the ack PDU capacity from within table 3A, or 3B and select the desired ack PDU based on input connection to ack PDU and compatibility of ack PDU receptacles with power cords. Additional ack PDUs are listed on page 7 and 8 if the listed ack PDU in these tables do not match your equipment configuration. This step is critical as the ack PDU must be able to connect to an input circuit on site and the servers and switches must have the correct type and quantity of receptacles to power up properly. STEP 4: Select Enclosures and Installation Diagrams. Depending on special constraints onsite, select the appropriate combination of enclosure width and depth. It is recommended using wide (750mm) and deep (1200mm) enclosures if space permits, as this offers the most flexibility during operation and ease of installation. 4

5 IBM BladeCenter H Power Step 1: Determine Power Configuration The IBM BladeCenter H Server Chassis includes options for four hot-swappable redundant power supplies. Schneider recommends using power cords with three C20 inlets for power distribution flexibility with ack PDUs. Follow the diagram below for a fully redundant 2N power configuration. ack PDU Source B ack PDU Source A Connect to C19 Outlets on ack PDU Step 2: Determine Anticipated Power Load Up to four 2980 W high-efficiency power supplies with load-balancing and failover capabilities provide additional reliability and protection. Max power consumption per chassis can range from 2.5 to 7.5 KW; while a typical peak power consumption is closer to 4-5kW. It is recommended to use BladeCenter Power Configurator to accurately predict the power and cooling required for specific configurations to enablie realistic planning of the proper power and cooling infrastructure. The calculator can be found on the IBM website. Power Capping via Active Energy Manager also be utilized to reduce the risk of overloading a circuit. The power capping value can only be set on a blade server, not on the chassis. The IBM H-chassis requires a unique IBM cord (shown at left) with 3 IEC C20 connectors to the rack PDU. Two primary feeds (16A max each) supply power to blades, while a 3rd specially labeled cord 5.5A max) is for the blower. Total power consumption for a typical configuration is 4-5kW or less per chassis enclosure. 5

6 IBM BladeCenter H Power Step 3: Determine Chassis Quantity The following tables show the maximum amount of BladeCenter H chassis which can be supported from a desired rack PDU. The data for Table 3A and 3B is organized based on the power capacity ratings for standard rack mount PDUs, showing both single phase and three phase options The tables show recommended Metered ack PDUs with a zero U form factor and IEC outlets. Please note that additional rack PDUs in different configurations are shown on page 7 and 8. Table 3A - North America Solutions Number of Chassis per ecommended PDU * Limited by number of C19 outlets on PDU ** Limited by internal circuit breaker capacity UL mandates 80% derating (16A)for continuous loads. Table 3B- International Solutions Number of Chassis per ack Based on Calculated Power Load * Limited by number of C19 outlets on PDU ** Limited by internal circuit breaker capacity (16A). 6

7 ack PDU Charts - Metered Metered ack Power Distribution Units (PDUs) provide active metering to enable energy optimization and circuit protection. User-defined alarm thresholds mitigate risk with real-time local and remote alerts to warn of potential circuit overloads. Metered ack PDUs provide power utilization data to allow Data Center managers to make informed decisions on load balancing and right sizing IT environments to lower total cost of ownership. AP8000 series Metered ack PDUs include real power monitoring, a temperature/humidity sensor port, locking IEC receptacles, and ultra low profile circuit breakers. Users can access and configure Metered ack PDUs through secure Web, SNMP, or Telnet Interfaces. ack PDUs recommended on page 6 and 7. AP8868 AP8866 AP8888 7

8 ack PDU Charts - Switched Switched ack Power Distribution Units (PDUs) enable advanced, user-customizable power control and active monitoring. emote outlet level controls allow power on/off functionality for power recycling to remotely reboot equipment and restrict unauthorized use of individual outlets. Power sequencing time delays allow users to define the order in which to power up or down attached equipment. Avoid circuit overload during power recovery and extend uptime of critical equipment by prioritizing the load shedding. Input Current metering provides real-time remote monitoring of connected loads. AP8000 series Switched ack PDUs include real power monitoring, a temperature/humidity sensor port, and locking IEC receptacles. User-defined alarms warn of potential circuit overloads before critical IT failures occur. Users can access, configure, and control Switched ack PDUs through secure Web, SNMP, or Telnet Interfaces. Metered by Outlet with Switching ack Power Distribution Units (PDUs) enable advanced, user-customizable power control and individual outlet power metering. 8

9 9

10 Enclosure ecommendations 600mm/24 Wide The following diagrams are intended to show how the BladeCenter H chassis fits within the different widths and depths of the NetShelter SX. Blade chassis in general offer unique challenges of space and access. The rear area needs to be completely clear of cable managers and PDUs in order to access the rear hot-swappable components. TOP VIEW Yellow areas show data cabling area. ecommended cable managers: A7710 The 1070mm (42 ) deep enclosure is not recommended due to lack of the space for cable management. If 1070mm deep must be used, maximize space by rotating PDUs 90 degrees so that the outlets are facing the rear. Use A7711 kit to rotate PDUs. Add right angle power cord kits to improve clearance with enclosure frame. For cable management, use A7540 Toolless Cable ing kit in any available space. The 1200mm (47 ) deep enclosure offers more mounting options for PDUs and cable managers. The above two diagrams show suggested options. PDUs should be mounted in rear-most toolless channels to avoid interference with blade chassis components. If it is preferred to mount PDUs on opposite sides, maximize space by rotating PDUs 90 degrees so that the outlets are facing the rear. ecommended cable manager A7710 mounted in toolless rear channels. AP8866 rack PDU shown in illustration; however, configuration would be common for any PDU selection. EA VIEW 10

11 Enclosure ecommendations 750mm/30 Wide The below diagrams show the available rear space for 750mm (30 ) wide NetShelter s and the recommended ack PDU and cable management options. TOP VIEW ack PDUs can be placed on either side of rack enclosure Yellow areas show data cabling area. ecommended cable managers: A7710, A7721, or A7580A 1200mm enclosure has additional space for access and cable management (can use additional A7721 kits or A7710 kits) The wider 750mm (30 ) enclosures are the recommended enclosures for blade applications. They offer the best clearance with absolutely no interference with the ack PDUs/cable managers and the removable modules of the blade chassis. ecommended cable manager A7710 mounted in toolless rear channels. EA VIEW 11