R&S RTO and R&S RTE Oscilloscopes Release Notes Firmware Version

Transcription

1 R&S RTO and R&S RTE Oscilloscopes Release Notes Firmware Version These Release Notes are for following models of the R&S RTO and R&S RTE: R&S RTO 1012, order no K12, R&S RTO 1014, order no K14, R&S RTO 1022, order no K22, R&S RTO 1024, order no K24, R&S RTO 1002, order no K02, R&S RTO 1012, order no K12, R&S RTO 1022, order no K22, R&S RTO 1044, order no K44 R&S RTE 1022, order no K22, R&S RTE 1032, order no K32, R&S RTE 1052, order no K52, R&S RTE 1102, order no K02, R&S RTO 1004, order no K04, R&S RTO 1014, order no K14, R&S RTO 1024, order no K24, R&S RTE 1024, order no K24, R&S RTE 1034, order no K34, R&S RTE 1054, order no K54, R&S RTE 1104, order no K04, R&S RTE 1022, order no K22, R&S RTE 1024, order no K24, R&S RTE 1032, order no K32, R&S RTE 1034, order no K34, R&S RTE 1052, order no K52, R&S RTE 1054, order no K54, R&S RTE 1102, order no K62, R&S RTE 1104, order no K64, R&S RTE 1152, order no K72, R&S RTE 1154, order no K74, R&S RTE 1202, order no K82, R&S RTE 1204, order no K Rohde & Schwarz GmbH & Co. KG Muehldorfstr. 15, Munich, Germany Phone: Fax: Internet: Subject to change. R&S is a registered trademark of Rohde & Schwarz GmbH & Co. KG. Trade names are trademarks of the owners. The following abbreviations are used throughout this document: R&S RTO is abbreviated as R&S RTO, R&S RTE as R&S RTE. Release Notes Test and Measurement PAD-T-M: /02.00/CI/1/EN/

2 Current Version and History New Functions Table of Contents 1 Current Version and History New Functions Modified Functions Improvements Known Issues Modifications to the Documentation Firmware Update Preparing the Installation Performing the Firmware Update on the Instrument Performing the Firmware Update without a running oscilloscope application Firmware downgrade Installing Firmware Options Customer Support Release Notes

3 Current Version and History 1 Current Version and History 1.1 New Functions The following table lists the new functions and indicates the version in which the new function was introduced: Version Function Support for Option R&S RTO-K42 - D-PHY Serial Triggering & Decoding Support for Option R&S RTx-K10 - SENT Serial Triggering & Decoding Support for trigger event as Source for action events, for example "Save on Trigger" New toolbar items for PrintScreen, Save SaveSet, Labelling, ClearScreen and Update ReferenceWaveform New toolbar items for Reset, Autoset, Run/Cont and Run Nx Single for easy operation in remote mode Intelligent arrangement of the measurement results in docked mode SmartGrid for ResultDialogs - easy positioning of result dialogs via the touchscreen Different selectable font size for result dialogs and settings dialogs When values are entered in a settings dialog, the digit keyboard dialog includes buttons for settings the values to its Min and Max values The maximum acquisition time is increased to sec/ Div for the RTO and 5000 sec/ Div for the RTE including the RollMode When changing the channel colors all channel icon colors are kept consistent A PRESET action can be undone with the UNDO feature Export of history now can be done including the time stamp for each waveform. This also works for the ultra segmentation mode Reference waveforms can be analyzed without an active channel doing its acquisition Support of automatic firmware update via internet (instruments with operating system Windows 7 Embedded only) Support of current probe R&S RT-ZC05B and R&S RT-ZC10B Ready for future support of current probe R&S RT-ZC Support for Option R&S RTO-K50 - Manchester and NRZ Serial Triggering & Decoding Support for Option R&S RTE-K50 - Manchester and NRZ Serial Triggering & Decoding Support for Option R&S RTO-K52-8b10b Serial Triggering & Decoding Support for Option R&S RTE-K60 - USB 1.0 /1.1 / 2.0 / HSIC Serial Triggering & Decoding Option R&S RTO-K60: Enhanced trigger capabilities (data, etc.) Option R&S RTx-K1: Search on I2C decode Option R&S RTx-K3: Search on LIN decode RTE: Support of Bandwidth Upgrades for RTE models Kxx RTE: Support of additional models RTE: Support of reference waveform offset Support of current probe R&S RT-ZC20B Support of square grid for the X/Y diagram Support for Option R&S RTO-K8 - Ethernet Serial Decoding Support for Option R&S RTE-K8 - Ethernet Serial Decoding Support for Option R&S RTE-K9 - CAN FD Serial Triggering & Decoding Option R&S RTx-K3 / K9: decode results support physical values derived from DBC import Option R&S RTx-K3 / K9: symbolic trigger on physical values derived from DBC import Option R&S RTO-K13: HW recovered clock can be displayed Release Notes

4 Current Version and History Version Function Option R&S RTO-K13: TIE measurements support HW-CDR Support for Option R&S RTO-B103 - Memory Upgrade 200 MSamples per Channel (instruments with operating system Windows 7 Embedded only) Support for Option R&S RTO-B104 - Memory Upgrade 400 MSamples per Channel (instruments with operating system Windows 7 Embedded only) Support for Option R&S RTO-K9 - CAN FD Serial Triggering & Decoding Support for Option R&S RTO-K17 - High Defintion Support for Option R&S RTE-K17 - High Defintion Support for Option R&S RTO-K55 - MDIO Serial Triggering & Decoding Support for Option R&S RTE-K55 - MDIO Serial Triggering & Decoding Option R&S RTx-B1: Export of all digital signals within a digital bus (remote data capture with ASCII format only) The signal bar includes the information about bandfilter width Support of measurements in RollMode Printing of waveforms with white background while keeping the waveform colors Additional unit % for THD measurements available Support of UNCAL and AD overflow status in remote status bit commands RTO: Reference Level settings for "Upper Manual - Lower Absolute Peak" added RTO: Compliance tests (R&S Scope Suite) can be started from the menu bar via Analysis > External Apps (instruments with operating system Windows 7 Embedded only) Multilingual support for Japanese and Korean user interface 1.2 Modified Functions The following table lists the modified functions and indicates the version in which the modification was carried out: Version Function Improved FileOpen/ FileSave Dialog for easy file selection Toolbar Icons updated for improved user experience Print Hardkey directly creates a screenshot image without showing the print settings dialog first Interval trigger is defined by the slope instead of the polartity. The Remote command has been adjusted The position of the floating result dialogs is restored when saving and loading a saveset The default color of a mathematics signal is set to "Spectrogram" if an FFT is included in the mathematics formula Better readability of grid labels when printing with white background RTE: Reference Levels can be defined as absolute values Group result dialogs turned on by default If a waveform is saved because of an event action (for example a mask violation), the filename is always based on the autonaming settings Improved accuracy of jitter measurement histograms Adjustment of N-cycle jitter algorithm with respect to the time difference between adjacent groups of N consecutive cycles Support of Demoboard firmware version V Option R&S RTx-K17: Available maximal digital bandwidth is adapted to analog instrument bandwidth Improved update rate in selected scenarios when time or frequency measurements are active, especially in combination with long record length Release Notes

5 Current Version and History Version Function FindLevel functionality improved for rectangular signals with strong overshoot Closing a measurement result dialog with the Cancel button disables the measurement. In older versions just the visibility was disabled Maximal font size for dialogs is increased When attaching a multilingual keyboard and the keyboard language is changed, there is no impact on the behavior of the Frontpanel keys (instruments with operating system Windows 7 Embedded only) Improved multilingual support for Chinese, German and Russian user interface Single Click on the Horizontal signal bar opens the Horizontal dialog; single click on the Trigger signal bar opens the Trigger Dialog Single Click on a Channel signal bar activates the channel, if the channel is not active. If the channel is already active the channel dialog is opened. 1.3 Improvements The following table lists the eliminated issues and indicates the version in which the issues were eliminated: Version Function In some cases single FFT frames showed deviations during the modification of FFT settings. This issue is fixed In some cases, "Oven cold" was indicated with the R&S RTx-B4 option even though the oven was in operating temperature, This issue is fixed LimitLine violations as action items is supported in RunContinous Mode Improved accuracy for AutoZero functionality, especially for HD-mode Option R&S RTx-B1: Binary display for I²C and SPI when using MSO is fixed Option R&S RTx-B1: The slope is correctly taken into account in delay measurements In some cases, when the frequency span of the FFT math function was considerably smaller than the RBW, the firmware stopped responding. This issue is fixed The logic of the math function "greater than" / "less than" was not always accurate enough. This issue is fixed Fixed delay measurement function for edge count direction "from last" RTx-K1: Fixed duplicated byte occurrence if frame is incomplete If folders for data export contained a dot in their name, a new folder was created with every export. This issue is fixed In some cases the label font size was reset when restarting the instrument. This issue is fixed RTO: When loading SaveSets with reference level settings for "Upper Manual - Lower Absolute Peak" being active, the upper manual value was not loaded correctly. This issue is fixed In some cases the RTx firmware did not respond any more when the instrument was connected via a remote desktop connection and serial protocols were activated. This issue is fixed RTx-K31: In some cases the RTx firmware did not respond any more when a SaveSet was loaded, that had Harmonic Measurements turned on. This issue is fixed In roll mode zooming, scaling and moving was not possible in stop mode before the first acquisition was completed. This issue is fixed Option R&S RTx-K3 / K9: Symbolic display supports rounded integer values whereas the trigger settings support a resolution of 0.1. This issue is fixed Fixed option key issue RTE: In same cases the grid labels were not well readable in printouts with white background. This issue is fixed. Release Notes

6 Current Version and History Version Function In some cases the grid configuration was not recalled correctly from SaveSets with FFT diagrams. This issue is fixed Reference waveforms could not always be disabled after AutoSet. This issue is fixed Correct display of result lines of duty cycle measurements 1.4 Known Issues The following table lists the known issues and indicates since which version the issue could be observed: Since Function None 1.5 Modifications to the Documentation Revision History: Date Release Notes Revision Changes Support for Option R&S RTO-K42 - D-PHY Serial Triggering & Decoding Support for Option R&S RTx-K10 - SENT Serial Triggering & Decoding Service pack related to math function "greater than" / "less than" Release of R&S RTO-K50, R&S RTO-K52, R&S RTE-K50 and R&S RTE-K RTE: Support of Bandwidth Upgrades for RTE models Kxx Support of additional R&S RTE models Correct handling of remote desktop connection when serial protocols are activated Support of current probe R&S RT-ZC20B Service pack related to option key issue Release of R&S RTO-K8, R&S RTE-K8, R&S RTE-K9, TIE on HW-CDR Release of R&S RTO-B103, R&S RTO-B104, R&S RTO-K9, R&S RTO-K17, R&S RTE-K17, R&S RTO-K55 and R&S RTE-K55 Release Notes

7 Firmware Update 2 Firmware Update Firmware updates for the R&S RTO and R&S RTE are available as a single download from the Rohde&Schwarz web page or The installation file for R&S RTO and R&S RTE with Windows 7 is named Setup_Rtx_V _x64.exe. The installation will be rejected, if the installation file is used on an RTO instrument with Windows XP. The installation file for R&S RTO with Windows XP is named Setup_Rto_V _x86.exe. The installation will be rejected, if the installation file is used on an RTO instrument with Windows 7. After the update to version RTx V the instrument will start with preset instrument settings. To check the installed firmware version select Setup from the File menu and switch to the system tab. The firmware version is shown in the upper left corner of this dialog. Important Notice: On R&S RTO with Windows XP updates from a firmware version below to or higher require an additional download file from the Rohde&Schwarz web page or This installation file is named RTO-GraphicDriverUpdate-1.01.msi. To check, if the latest graphics driver version is installed on the instrument R&S RTO with Windows XP, change to the desktop of the instrument. The desktop is available by selecting the item Minimize Application of the File menu. Open the context menu of the main window with a right mouse click and select the menu item Graphics Properties. The following dialog box shall appear: Release Notes

8 Firmware Update If the dialog box on the screen looks different to the one above, an old driver is installed. Select the button Options and Support. A menu appears below. Select the item Information Center of this menu. On the right side a list of properties appears. The third property is titled Driver Version: Check the Version number. The latest driver has the version number Because older graphics driver versions may cause firmware crashes it is strongly recommended to install the latest version. 2.1 Preparing the Installation There are several ways how to update the device after downloading the firmware installation file. Please make sure, that the installation file Setup_Rtx_V _x64.exe is used for R&S RTO and R&S RTE with Windows 7. Setup_Rto_V _x86.exe is used for R&S RTO with Windows XP. Using a memory stick: 1. Copy the file(s) to a directory of the memory stick and insert the memory stick into one of the USB sockets of the instrument. Using the remote desktop and copying the installation files to a directory of the instrument: 1. Connect the instrument to your LAN 2. Start the remote desktop on your PC (C:\winnt\system32\mstsc.exe) Release Notes

9 Firmware Update 3. Enter the TCP/IP address of the instrument that you want to update. Ensure that the local resources > drives option is selected and press the Connect button 4. Login to the instrument (user name: instrument and password by default) 5. Copy the firmware installation file and, if necessary, the graphics installation file RTO-GraphicDriverUpdate-1.01.msi from your PC to a new folder on the instrument 6. You can now access this directory with the installation file from the instrument firmware Using a network drive: 1. Connect your instrument to your LAN, and establish a connection to one of your servers (ask your local IT administrator for support) 2. Copy the firmware installation file and, if necessary, the graphics installation file RTO-GraphicDriverUpdate-1.01.msi from your PC to a directory on this server 3. You can now access the directory with the installation file from the instrument firmware 2.2 Performing the Firmware Update on the Instrument The firmware update process is performed with the following steps: 1. Switch the instrument on and wait until the Oscilloscope has resumed operation 2. Ensure that the acquisition mode is not running. If the RUN CONT or the RUN Nx SINGLE key is shining green, press this key to stop the acquisition 3. Press the SETUP key or select Setup from the File menu at the bottom of the screen 4. Select the System tab 5. The selected dialog box contains a box with the title Select setup for firmware update. Press the Button Open within this box. A file selection dialog appears 6. Change the path to the drive and directory which you prepared in the step 2.1 (USB stick directory, remote PC directory or directory on a server) and close the dialog with the Select button 7. The installation starts and a new dialog box appears. Press the Next button to navigate to the selection of the firmware packages. By default all applications should be installed 8. Press the Install button to start the firmware update: The installation continues and the firmware is stopped. After a few minutes the system restarts automatically. Depending on the previously installed firmware version, a reconfiguration of the hardware may be required during the first start of the firmware. In this case, a message box is displayed and the update of the FPGA starts automatically. Do not switch off the instrument during this update! After the update of the FPGA Release Notes

10 Firmware Update the instrument performs another instrument restart automatically. If a special FPGA update is required the instrument must execute a cold boot. In such a case, a message appears on the screen asking to switch off the instrument. Press the Ok button and wait until the instrument is completely switched off. As a final step switch on the instrument. The instrument resumes operation. 9. As mentioned above the upgrade of the RTO from a firmware version less than (e.g x.x, 1.10.x.x or 1.0.x.x) to version or higher requires an additional update. To check the installed firmware version select Setup from the File menu and switch to the system tab. The firmware version is shown at the upper left corner of this dialog. If the version is less than install an additional firmware package for a graphics driver update: a) Download the file RTO-GraphicDriverUpdate-1.01.msi from the RTO home page and copy it to the instrument or to a memory stick b) Stop the instruments firmware with the Item Exit of the File menu c) Uninstall the old graphics driver in the following way: Open the windows control panel from the windows start menu (Start Settings Control panel). Select the icon Add or remove software. After a few seconds a list of all installed software packages appears. Select Intel Graphics Media Accelerator Driver. Additional information for this software appears. Press the button Remove and wait until the process is complete. d) Start the windows explorer on the desktop of the RTO and navigate to the directory with the installation file RTO-GraphicDriverUpdate-1.01.msi e) Double click on this file and wait until the installation is complete. This will take several minutes f) After a few seconds the instrument executes a reboot g) After the reboot an automatic installation will be started to setup the MS.net Framework. During this installation the instrument cannot be used as a normal Oscilloscope. The installation takes about 10 minutes. After the installation is complete another reboot is executed automatically h) After the second reboot the graphics driver update is complete 10. After the firmware update a self alignment is recommended. Select Self alignment from the File menu. Select Start Alignment to start the self alignment procedure. A message box appears to indicate the running alignment procedure. Wait until this message box disappears. This will take several minutes. Now the instrument is ready for operation. 2.3 Performing the Firmware Update without a running oscilloscope application If a firmware update shall be executed without running firmware, the windows explorer can be started. Change the path to the drive and directory prepared in step 2.1. Make a double click on this file and proceed with step 7 to update the instrument firmware. Release Notes

11 Firmware Update 2.4 Firmware downgrade A firmware downgrade is handled like a normal firmware installation with the following exceptions: R&S RTO Firmware downgrade from version 2.0 or higher to version 1.60 or lower is not supported for instruments with Windows 7: A firmware downgrade from version 2.0 or higher to version 1.60 or lower is only possible on RTO instruments with Windows XP. 2.5 Installing Firmware Options The firmware update includes all currently available firmware options. No additional installation is required. A firmware update has no side effects to firmware options already installed. The instructions in this chapter are only needed, if a firmware option is purchased and needs to be enabled on the instrument. Enabling Options by Entering Option Key Codes To activate firmware options, enter a license key for validation. The license key is in the device certificate or delivered as a part of the software package. The process is performed in the following steps: 1. Press the SETUP key. A dialog box appears. Select the SW options tab. The selected tab contains a box with the title Install a new option. There are two ways to install a firmware option: a) If a file including the option key is provided, select Open in the box with the title Install from file. Navigate to the directory containing the option key file. Choose the file and click Select b) If an option key number is provided double click on the data entry filed with the title Enter new option key. A key pad appears. Enter the option key number and press the Enter button. 2. After successful validation the message option key valid is displayed. If the validation failed, the firmware option is not installed. 3. If more than one firmware option shall be installed, step 1 and 2 needs to be repeated several times. 4. Reboot the device or restart the firmware. Release Notes

12 Customer Support 3 Customer Support Technical support where and when you need it For quick, expert help with any Rohde & Schwarz equipment, contact one of our Customer Support Centers. A team of highly qualified engineers provides telephone support and will work with you to find a solution to your query on any aspect of the operation, programming or applications of Rohde & Schwarz equipment. Up-to-date information and upgrades To keep your instrument up-to-date and to be informed about new application notes related to your instrument, please send an to the Customer Support Center stating your instrument and your wish. We will take care that you will get the right information. Europe, Africa, Middle East Phone customersupport@rohde-schwarz.com North America Phone TEST-RSA ( ) customer.support@rsa.rohde-schwarz.com Latin America Phone customersupport.la@rohde-schwarz.com Asia/Pacific Phone customersupport.asia@rohde-schwarz.com China Phone / customersupport.china@rohde-schwarz.com Release Notes