HOSE, COUPLINGS, FITTINGS AND ACCESSORIES CATALOG

Transcription

1 Certified ISO 9002 HOSE, COUPLINGS, FITTINGS AND ACCESSORIES CATALOG Our Mission Summers Rubber Company provides solutions to our customers needs by distributing and fabricating specialty components that convey, connect and seal industrial applications where flexibility and flow are an sintegral part of a process system.

2 Instant Access to Thousands of Products Summers extensive regional inventories include thousands of products from hundreds of the world s leading hose product manufacturers. Brand names you can rely on for quality, value and performance. Not far from your location, Summers has industrial hose brands such as Gates, Boston, HBD-Thermoid, Goodyear and Kanaflex. Hydraulic hose and fittings from Gates, Hansen and Brennan. Quality couplings from Civacon-OPW, Dixon, Hansen and Victaulic-Drylink. Teflon and metal expansion joints from Hosemaster, Senior Flexonics, Flexible Components and Jackson. Ducts from Flexaust and Federal. Sealing products and gaskets from Durametallic and Boston Sheet. Plus many, many more on a resource list that continues to grow in tandem with today s hose and hose application technology. On-site Services to Save You Time and Money Summers helps you improve the efficiency and productivity of your purchasing and maintenance functions with the following on-site services: Hose assembly preventive maintenance tracking. Special stocking agreements. Service level reports. Custom labeling. Hose assembly pressure testing and certification. Kit assembly and packaging. Inventory management. Delivery service. Plant surveys for application improvements and safety. Store room inventory reduction analysis. Just In Time delivery for MRO and OEM programs. Private labeling of hose and fittings. Conveniently Located for Fast Service The Summers regional warehousing network provides fast, complete service to customers in Ohio, Pennsylvania and nearby states. Our locations are fully inventoried and staffed with competent knowledgeable people who can quickly handle requests over the counter, over the phone, by fax or mail. Need it extra fast? No problem. We can arrange for fast deliveries with our own fleet of trucks. Summers Rubber Company 2 Berea Road Cleveland, OH 44 Phone: Toll-free: Fax: Summers Rubber of Findlay 22 Lima Avenue Findlay, OH 4840 Phone: Toll-free: Fax: Summers Rubber of Eastlake 00 Lakeland Boulevard Eastlake, OH Phone: Toll-free: Fax: Summers Rubber of New Castle, Quality Hose & Supply Division 0 North Liberty Street New Castle, PA 602 Phone: Toll-free: Fax: Summers Rubber of Mansfield 60 West Longview Avenue Mansfield, OH 4490 Phone: Toll-free: Fax: Summers Rubber of Dover RD Dover, OH Phone: Toll-free: Fax: Summers Rubber of Marietta Route 7 & Tennis Center Drive Marietta, OH 470 Phone: Toll-free: Fax: Summers Rubber of Akron 489 Kelly Avenue Akron, OH 4406 Phone: Toll-free: Fax:

3 TABLE OF CONTENTS INDUSTRIAL HOSE Air, Water, Fire, Steam, Material Handling, Food Grade, Marine, Petroleum, Chemical, Sandblast, Plastic (PVC), LPG and Special Application, Tubing and Push-on Tube Fittings HOSE COUPLINGS, FITTINGS, CLAMPS AND ACCESSORIES Nipples, Barbed Inserts, Hydrant Adapters, Garden Hose Fittings and Adapters SPECIAL APPLICATION HOSES, METAL AND TEFLON HOSE DUCTING HOSE QUICK DISCONNECTS Cam and Groove (Fluid and Dry), Industrial Interchange, Chicago (Claw Type), High Pressure and Special Applications TECHNICAL DATA HYDRAULIC HOSE FITTINGS AND ADAPTERS GASKETS AND SEALING PRODUCTS SHEET RUBBER AND SPONGE RUBBER POWER TRANSMISSION PRODUCTS SWIVEL, ROTARY, BALL JOINTS AND VALVES CONVEYOR BELTS AND FASTENERS GLOVES, RAIN GEAR, LUBRICANTS AND MISCELLANEOUS SUPPLIES Copyright 998 Summers Rubber Company, Cleveland, Ohio 44

4 ALPHABETICAL INDEX Index A Acid Suit Adapters and Tube Fittings Brass Flange Garden Hose Hydrant Hydraulic Agricultural PVC Water Suction/Discharge Hose Agricultural Spray Special Application Hose Air Brake Hose Air Conditioning Hose Air Drill Hose Air Fittings and Accessories Ball Swivels In-Line Swivels Push-On Ball Swivels Air Fittings and Accessories Air Hose , 8 Air Tool Hose , 9 Alcohol Petroleum Hose Anti Freeze Petroleum Hose Aromatic Solvents Chemical Hose 2 B Ball Valves Brass Full Port High Pressure Polypropylene Single Union Stainless Steel Barco Joints Beverage Hose Blower Material Handling Hose... 6 Boots Brass Barbed Hose Fittings Brass Compression Fittings Brass Pipe Fittings Brass Push-On Tube Fittings Brewery Beverage Hose Bull Air Hose Burning Special Application Hose.. 4 Butane-Propane Petroleum Hose.. C Cam and Groove Cautionary Statement Cement Blower Hose Chemical Suit Clamps BAND-IT BAND-IT Tool Bolt Type Bridge Buckles Center Punch Clamp Tool for Pinch-On Clamps Double Ear Giant Tool High Torque Hose Support Make-A-Clamp Miniature Pinch-On Punch Tools Radiator C continued Clamps continued Screw/Radiator Spiral/Power Clamp T-Bolt Worm Gear Clear Braided Multi-Purpose Tubing Clear Vinyl Multi-Purpose Tubing, FDAApproved Composite Chemical Hose Concrete Pump Material Handling Hose Contractors Grade Suction/Discharge Hose Contractors Air Hose Contractors Water Hose Convertapipe Special Application Hose Conveyor Belts and Fasteners Belt Accessories Conveyor Terms and Definitions 298 Edge Finishes , 29 Elevator Belting Fabrications Fabrications, Standard I Cleats. 29 Flexco Fasteners Food Handling Belts Heavy-Duty Conveyor Hole Punching, Perforating Incline Belts Longitudinal Splicing Mechanical Fasteners Monofilament Thermoplastic Belting Notching PVC Conveyor Precision Grinding Splicing Urethane Cleats Urethane Specialties V-Guides Coolant Hose Coupling Accessories Manifolds Air Tool Swivels Blow Gun In-Line Lubricators Rubber Tipped Blow Gun Washers Whipcheck Safety Cable Coupling Summary Information... 6 Couplings Air Fittings Air Fittings and Accessories Air King Universal Couplings Brass Compression Fittings Crimped Steam Hose Double U-Bolt Fire Hose Nozzle Ground Joint Ground Joint Fittings Ground Joint Viton Seal Couplings Sand Blast Couplings Single U-Bolt U-Bolt Clamps Water Nozzles Whip Check Safety Cable Couplings, Pipe Fittings (NPT) Brass C continued Couplings, Pipe Fittings NPT cont. Bushing, Coupling Hose Ends , 7 Hydraulic Couplings, Fittings and Accessories Barbed Hose Fittings Female NPT Male NPT Brass Ball Valves Brass Short Shank Fittings Female, GHT Male, GHT Bushing Female NPT Swivel Fitting, Ball Seat GHTAdapters Mender Nylon Inserts Pipe Nipple Push-On Fittings Reducer Coupling Couplings, Food Grade Fittings Acme Thread Hex Nuts Bevel Seat Female Bevel Seat Gaskets CB Fittings Male NPT Stem Sanitary Clamp Sanitary End Stem Sanitary Gaskets Couplings, Nozzles Fire Hose Nozzle Water Nozzles Play Pipes Couplings, Shank Type Fittings Brass Hose Mender Brass NPT Ends Carbon Plated Steel Foot Valve Grooved End Jump Sizes Long Shank Long Shank Couplings Short Shank, Brass Swivel Nut.. 69 Skimmer Stainless Steel Steel Hose Mender Tri-Lokt Hose Nipples Unplated Steel, Plated Steel Coupling, Steam , 6-64, 40 Crack Filler Material Handling Hose 9 Credit Application Crimped Steam Hose Couplings.. 4 Cross-Linked Polyethylene Chemical Tube Crush Resistant Chemical Hose.. 2 Crush Resistant Polyethylene Chemical Tube Crush Resistant Teflon Lined Chemical Tube Cryogenic Special Application Hose 0 Custom Made Rubber Cut Sheet Rubber D Dairy Water Hose Debris Collector Material Handling Hose Die Cut

5 ALPHABETICAL INDEX Index continued D continued Diesel Petroleum Hose Divers Air Special Application Hose Dredge Sleeve Material Handling Tube Dredge Sleeves Special Application Hose Drop Sleeves Material Handling Hose Drop Sleeves Material Handling Tubing Dry Cement Delivery Material Handling Hose Dry Material Suction/Discharge, Bulk, FDA Hose Ducting Hoses Chip Handling Crush-proof Custom Built Flexible Ducting.. Dust Collection , External Orange Wearstrip Flexible Hose and Ducting Hose Summary Fume Removal Hot Air Insulation Blowing Leaf Loading and Collection Light Weight Plastic Vacuum... 2 Polyethylene Polyvinylchloride (PVC) Silicone Stainless Steel Straw Blowing Swimming Pool Thermoplastic Rubber Urethane Vacuum Vent White E EPDM Chemical Tube Elephant Trunk Material Handling Hose Emulsion Material Handling Hose Expansion Joints Concentric, Eccentric Reducers. 06 Lateral/Axial Offset Metal Rubber Specification Sheet Spherical Spool-Type Teflon Wire Arch Exhaust Hose, See Duct Hose09-2 Extruded Rubber Goods See Molded/Extruded Rubber Goods 299 F FDA Food and Beverage Tube., 4 FDA, A Standards Food and Beverage Hose Farm Spray Special Application Hose Fire Hose Nozzle Fittings, See Couplings Flexco Fasteners F continued Flanges Hydraulic Pipe , 98, 04 Sanitary Flexlock Connector Flexseal Connector Food Grade Fittings Food Grade Service PVC Water Suction/Discharge Food Hose Fuel Delivery Petroleum Hose.... Furnace Coolant Special Application Hose G Garage Exhaust Hose and Accessories Garden Hose Garden Hose Adapters Gaskets and Sealing Products Accessories Bearing Gard Braided Compression Packing.. 20 Compressed Gasket Material Cut Rubber and Gasket Material 247 Flange and Valve Shields Gasketing on a Roll Jacketed and Solid Metal Gaskets Lip Seal O-Rings Sealing Technical Service Questionnaire Seals, Mechanical, See Mechanical Seals Spiral-Wound Gaskets Gasoline Drop Petroleum Hose... 2 Gasoline Petroleum Hose Gauges Dry Liquid Filled General Service Multi-Purpose Hose Gloves Chemical Resistant General Purpose Special Purpose Gorilla Multi-Purpose Hose Grass, Leaves, Dust and Air PVC Discharge Hose Ground Joint Fittings Grout Material Handling Hose Gum Sleeves Material Handling Tubing H Handbuilt Specialty Hose Heater Hose Herbicides Special Application Hose4 Hi-Temp Hose High Heat Applications Insulated Hose Sleeving, Rope, Tape High Pressure Air Hose Hose Reels Manual Rewind Portable Storage Power Rewind Spring Rewind , 89 H continued Hose and Hose Coupling Safety. 06 Hose Selection Guide Hoses, Air Air Drill Air Tool , 9 Bull Contractors Air General Service High Pressure Multi-Purpose Recoil , 9 Self Storing , 9 Wire Braid Hoses, Chemical Aromatic Solvents Composite Cross-Linked Polyethylene Tube. 2 Crush Resistant Crush Resistant Polyethylene Tube Crush Resistant Teflon Lined Tube EPDM Tube Naptha , 27 Paint/Chemical (special flexible nylon material). 28 Solvents Aromatic Tallow Teflon Lined Tube Teflon Tube Ultrahigh Molecular Weight Polyethylene Tube Hoses, Ducting See Ducting Hoses Hoses, Food and Beverage Beverage Brewery FDATube FDA, A Standards Food Milk Potable Water Wine and Water Based FDA Hoses, Hydraulic See Hydraulic Hoses Hoses, Material Handling Blower Cement Blower Concrete Pump Crack Filler Debris Collector Dredge Sleeve Drop Sleeves , 9 Dry Cement Delivery Dry Material Suction/Discharge, Bulk, FDAApproved Elephant Trunk Emulsion Grout Gum Sleeves Hot Air Blower Material Handling Municipal Vacuum Plaster Pure Gum Tubing Rubber Tar and Asphalt Sand Blast Shot Blast Slurry

6 ALPHABETICAL INDEX Index continued H continued Hoses, Material Handling continued Tar Patching Vac All Hoses, Metal See Metal Hoses Hoses, Metric Thermoplastic Tubing Nylon Metric Tubing Polyethylene Metric Tubing..... Polyurethane Metric Tubing Hoses, Multi-Purpose Clear Braided Tubing Clear Vinyl Tubing, FDA Approved General Service Gorilla Lock-On Non-Conductive PVC General Purpose Pot Room Push-On Terminator Hoses, PVC Water Suction/Discharge Agricultural Food Grade Service Grass, Leaves, Dust, Air Discharge24 Heavy-Duty Heavy-Duty Armour Guard Discharge Light-Duty Marine Septic Static Wire Hoses, Petroleum Alcohol Anti Freeze Butane-Propane Diesel Fuel Delivery Gasoline Gasoline Drop LPG Oil Field Suction/Discharge Tank Truck Vapor Recovery Hoses, Pneumatic Tubing Nylon (Flexible) Polyethylene Polyurethane Hoses, Special Application Agriculture Spray Air Brake Burning Convertapipe Coolant Cryogenic Divers Air Dredge Sleeves Farm Spray Flexlock Connector Flexseal Connector Furnace Coolant Handbuilt Specialty Hose Built-In Nipple Combination Nipple Flexlock End 2# ANSI Flange 49 Flexseal End Soft Capped End Straight End Capped Heater Herbicides H continued Hoses, Special Application continued Hi-Temp Jetting Marine Marine Exhaust Non-Conductive Orchard Spray Out Gassing Oxygen Oxygen/Acetylene Paint Spray Sand Suction Scarfing Sewer Cleaning Silicone Spraying Waterblast Welding Hoses, Steam/Pressure Washer Pressure Washer Steam Steam Cleaner Hoses, Water Contractors Water Dairy Garden Hot Water Wash Down Municipal Non-Marking Sanitary Hoses, Water Suction/Discharge Contractor Grade Suction/Discharge Heavy-Duty PVC Lay Flat Discharge Mill Stationary Water Discharge.. 22 Pump Discharge PVC Lay Flat Discharge Rubber Discharge Water Suction Hot Air Blower Material Handling Hose Hot Water Wash Down Hose Hydrant Adapters Hydrant Adapter Cleveland Fire Dept. Thread National Standard Thread Hydraulic Hose Hydraulic Hose Fittings and Adapters Adapters and Tube Fittings Agency Specifications BSP Thread Adapters Banjo Fittings Bend Restrictor Coupling Selection Crimp Equipment Flat-Face O-Ring Plugs, Caps and Adapters Flat-Face O-Rings Adapters Forged SAE Flange Adapters and Accessories High Pressure Adapter 000 psi 22 High Pressure Adapter 6000 psi 22 High Pressure Hydraulic Swivel Joints Hose Protection Products Hose Selection Guide H continued Hydraulic Hose Fittings and Adapters continued How to Order Hydraulic Fitting Selection Nomenclature Hydraulic Hose Interchange Hydraulic Steel Tubing Metric Thread Adapters Metric Tube Fittings Metrically Dimensioned Steel Tubing Micro Hose Assemblies Pressure Test Systems O-Ring Flange to JIC O-Rings for Code 6, Code 62, Caterpillar Style Flange Fittings Protective Sleeve SAE Flanges SAE Four Bolt Connections Selecting The Proper Hose Spring Guards Steel Flareless Fittings Swivel Joints Thread Configurations Tube Fitting and Adapters Hydraulic Technical Data 7 Flare (JIC) SAE (4 Flare) Bend Radius British Thread Types British Standard Pipe Parallel.. 4 British Standard Pipe Tapered.. 4 Coupling Identification Thread Identification Tool DIN 24 Cone DIN 60 Cone Flareless Tube Flow Capacity French Thread Types GAZ GAZ Poclain 24 Flange German DIN Thread Types Grease Fittings Hose Assembly Routing Tips Japanese 0 Flare Parallel Threads Japanese Tapered Pipe Thread. 9 Japanese Thread Types Komatsu Style 0 Flare Komatsu Style Flange Fitting Metric Standpipe Assembly Nomographic Chart North American Thread Types O-Ring Boss O-Ring Face Seal (ORFS) J O-Ring Flange SAE J8... Parker Triple Thread Flare Fittings Press-Lok Connectors Pressure Drop SAE Inverted Flare SAE Recommended Practice Thread Identification Tools Whitworth Thread

7 ALPHABETICAL INDEX Index continued I Industrial Technical Data Corrosion Agents to Materials Corrosion Resistance Dimensions of Steel Flanges... 7 Dimensions of Steel Pipe Dimensions of Tank Truck Flanges End Force Chart Feet of Water to Inches of Mercury Fraction/Decimal Conversion Chart Steam Temperature/Pressure Conversion Guide Temperature Conversions Thread Dimensions Thread Sealing Tips Threading Threads Injection Molding Coupling Insulated Hose J Jetting Special Application Hose.. 47 Joint Sealant K Kamlok Kamvalok L LPG Petroleum Hose Leaf Collection Hose Light-Duty PVC Water Suction/Discharge Hose Load Arms Lock-On Multi-Purpose Hose Lubricants and Misc. Supplies Anti-Seize Lubricant Belt Dressing Cable Ties Cleaning Solvent Degreaser Gasket Remover Gear, Chain and Cable Lubricant 04 Hydraulic Oil Hydraulic Sealant Lubricants Marking Paints Nickel Anti-Seize Lubricant O-Ring Making Kit Penetrating Oil Pipe Sealant Pliobond 20 Adhesive Removable Threadlocker Sealants Silicone Lubricant Teflon Tape Thread Sealant M Machinery Mounts Marine Exhaust Hose Marine PVC Water Suction/Discharge Hose Marine Special Application Hose.. 44 Material Handling Hose Matting M continued Mechanical Seals Back-up Designed Cartridge Inside Bellows Metal Bellows Mixer Applications Outside Bellows Single, Pusher Split Menders, Hose , 7 Metal Hoses Chemical Transfer Chlorine Transfer Corrugated Fabricated Corrugated Assemblies9 Fabricated Interlock Assemblies. 98 Interlocked Interlocked Fabricated Assemblies Special Fabricated Assemblies Guarded Assembly Jacketed Assembly Lined Assembly Traced Assembly Metric Push-On Tube Fittings.. -6 Milk Suction/Discharge Hose Mill Stationary Water Discharge Hose Mold Mate Coupling Molded/Extruded Rubber Goods Extrusions Grommets Latex Dipped Molded Vibration Mounts Multi-Purpose Hose Municipal Hose Municipal Vacuum Material Handling Hose N Naptha Chemical Hose Naptha Chemical Tube Non-Conductive Hose Non-Conductive Special Application Hose Non-Marking Water Hose Nozzles Automatic Shut-Off Fleet Service Fuel Oil Delivery Service Water Nylon (Flexible) Pneumatic Tubing. Nylon Metric Thermoplastic Tubing. O O-Rings Oil Field Suction/Discharge Petoleum Hose Orchard Spray Special Application Hose Out Gassing Special Application Hose Oxygen Special Application Hose.. 4 Oxygen/Acetylene Special Application Hose P PVC General Purpose Hose..... P continued PVC Heavy Duty Discharge PVC Lay Flat Discharge Hose PVC Water Suction/Discharge Hose. 2 Packing-Compression Paint Spray Special Application Hose0 Pipe Fittings (NPT) Brass Bushing, Coupling Hose Ends , 7 Hydraulic Paint/Chemical Hose (special flexible nylon material).. 28 Plaster Material Handling Hose... 8 Plastic Push-On Tube Fittings Polyethylene Metric Thermoplastic Tubing Polyethylene Pneumatic Tubing... Polyurethane Metric Thermoplastic Tubing Polyurethane Pneumatic Tubing.. Potable Water Hose Pot Room Hose Power Transmission Products HTD Belt Drives Long-Length Belting Mini-Pitch Belting Nu-T-Link Belting Poly Chain GT Belt Products Supreme V-Link Belting Timing Belt Drives Twin Power Belts V-Belts, See V-Belts Power Wash Power Washer Accessories Pressure Washer Gun Spray Nozzles Wand Pressure Washer Accessories Pressure Washer Hose Pressure Washer and Steam Cleaner Hose Protective Suit Pump Discharge Hose Pure Gum Material Handling Tubing 9 Push-On Multi-Purpose Hose Push-On Tube Fittings Brass Push-In Tube Fittings Compression Fitting Male Swivel Barb Fittings Metric Push-In Tube Fittings.. -6 Plastic Push-In Tube Fittings. 7-8 Splicing Union Kit Q Quick Connect Couplings ARO Agricultural Applications Agricultural Hydraulic Quick Connect Fittings Flat Face Flo-Temp Gas-Mate Coupling Heavy-Duty Wing Nut High Pressure Hydraulic Two-Way Shut-Off Industrial Interchange Injection Molding Mold Mate

8 ALPHABETICAL INDEX Index continued Q continued Quick Connect Couplings One-Way Couplings One-Way Special Application Couplings Pioneer Plastic Socket and Plug Power Wash Applications Safeway Agricultural Series Free Angle Socket and Plug Plastic Dust Caps Steam Coupling Straight Thru Couplings Truflate Plugs Two-Way Couplings Ultra Pressure Quick Disconnect Couplings Accessories Autolok Cam and Groove Cam and Groove Elbows Cam and Groove Lockable Dust Caps Cam and Groove Polypropylene Elbows Cam and Groove Reducing Adapters and Couplers Cam and Groove Reducing Couplers x Adapters Cam and Groove Specialty Items Cam and Groove Spool Adapters Couplers Cam and Groove, 0# Flanged Drilling Coupler s Kits Dry Disconnect Coupling Actuators Dry Disconnect Couplings Dry Disconnect Hose Coupling Dry Link Dual Ball Valve Design Gaskets for Kam and Groove Fittings Kamlok Kamvalok Polypropylene Cam and Groove Fittings The Smartlok System, Hose-Manifold Match Twin-Kam R Rain Gear Jacket Overall Overshoe PVC Rainsuit Raincoat Slicker Boot Recoil Air Hose , 9 Refrigeration Hose Rotary Joints Rubber Discharge Hose Rubber Sheeting, See Sheet Rubber Rubber Tar and Asphalt Material Handling Hose S SAE Flanges Safety, Hose and Hose Coupling. 06 Sand Blast Fittings, See Couplings Sand Blast Hose Sand Suction Special Application Hose Sanitary Fittings, See Couplings Sanitary Water Hose Scarfing Special Application Hose. 4 Sealants Selecting The Proper Hose Self Storing Hose , 9 Septic PVC Water Suction/Discharge Hose Sewer Cleaning Special Application Hose Sheet Gasketing , Sheet Rubber and Sponge Rubber Buna N Sheet Butyl Sheet Chute Lining Closed Cell Sponge Sheet Cloth Inserted Sheet Diaphram Sheet EPDM Sheet Food Grade Vinyl Sheet Gum Sheet Hypalon Sheet Industrial Matting Industrial Matting: Ergonomic, Anti-Fatigue, Safety Products. 26 Military Specification Sheeting.. 28 Neoprene Sheet Open Cell Sponge Sheet SBR Sheet Sheet Rubber Silicone Sheet Skirtboard Teflon Molded Sheet Urethane Rollers Urethane Sheet, Rod, Tubing Urethane Wheels Viton Sheet Shot Blast Hose Sight Flow Indicators, Ball Silicone Hose Sleeves Drop Elephant Gum Slicker Boot Slurry Hose Solvents Aromatic Chemical Hose. 2 Special Fabricated Assemblies Spring Guard Spraying Hose Stair Tread Strips Static Wire PVC Water Suction/Discharge Hose Steam Couplings Ground Joint Quick Connect Steam Hose Steam Cleaner Hose Strainers Swimming Pool Hose Swivel Joints , How to Order Swivel Joints Loading Arms T Tallow Chemical Tube Tank Truck Petroleum Hose Tapes, Teflon Tar and Asphalt Fittings Tar Patching Hose Teflon Fittings, Large Bore Teflon Chemical Tube Teflon Hose Assemblies Convoluted and Rubber Covered Teflon FDA (Food and Drug Administration) Fitting Options How to Order Convoluted and Rubber How to Order Small Bore Large Bore, Convoluted Tube (/8 thru ) Power Trim Rubber Covered Teflon Smooth Tube Small Bore (thru ) Teflon Lined Chemical Tube Teflon Tapes Terminator Multi-Purpose Hose... 4 Terms and Conditions of Sale Thread Data Thread Sealants Tube Fitting and Adapters Tubing Braided Gum Nylon Vinyl U Ultrahigh Molecular Weight Polyethylene Chemical Tube V V-Belts Heavy-Duty ASection B Section C Section D Section E Section Light-Duty PoweRated Molded Notch Vac All Material Handling Hose... Vacuum Hose Valves Ball Sight Flow Indicators VISI-FLO Vapor Recovery Petroleum Hose.. 2 Vent Hose Vibration Pads Machinery Mounts 29 W Wash Down Hose Water Nozzles Water Suction/Discharge Hose Waterblast Special Application Hose Welding Special Application Hose. 4 Wine and Water Based FDA Beverage Hose Wire Braid Air Hose

9 TERMS AND CONDITIONS OF SALE Summers Rubber Company s Terms and Conditions of Sale General. All prices, and these Terms and Conditions of Sale are subject to change by Summers Rubber Company without prior notice. 2. Upon placement of the purchase order, Buyer agrees to the exclusive application of Summers Rubber Company s Terms and Conditions of Sale.. All orders placed on account are subject to a minimum charge of $ All claims must be made within seven (7) days of receipt of merchandise. Payment Terms. Except as may be stated on invoice, payment terms for approved credit sales are % ten (0) days, net thirty (0) days. Only such invoices paid within ten (0) days of the invoice date, shall be entitled to the % discount. Summers Rubber Company reserves the right to alter payment terms based on Buyer s payment history. 2. Summers Rubber Company reserves the right to hold shipments against past due accounts. Freight Terms, Goods Damaged or Shorted in Shipment. All shipments will be made F.O.B., Destination. Buyer shall be responsible for clearly noting any shortages or damages on the delivery receipt (freight bill). Upon delivery, Buyer is also required to immediately notify Summers Rubber Company by phone or fax of any damages or shortages. 2. Backorders will be shipped in the most practical fashion with charges consistent with the freight policy established under the original order. Acceptance, Alteration and Cancellation of Orders. Orders for fabricated goods, non-standard items, or non-standard lengths, may not be cancelled after production has occurred or any other costs incurred. Return of Defective Merchandise. Defective or failed goods shall be held at Buyer s premises until authorization has been granted by Summers Rubber Company to return the goods, freight pre-paid, or dispose of the goods. Credit, based on prices at time of purchase, will be issued for goods found to be defective by Summers Rubber Company upon inspection. Goods Shipped in Error Buyer must notify Summers Rubber Company immediately on any goods shipped in error. Upon notification, the goods are to be returned to Summers Rubber Company either via truck or UPS on a freight collect basis. Buyer will be reimbursed for cost of such goods. Merchandise Ordered in Error Standard packaged goods only may be returned, provided that the goods are in the Buyer s possession no more than thirty (0) days. If such goods are accepted for return, the goods must be returned freight prepaid and Buyer will be charged (i) a minimum of 20% of the purchase price to cover restocking and handling charge, plus (ii) the outbound freight charges if the goods had been shipped to Buyer prepaid. Returns are not accepted for goods that are specially manufactured to meet the Buyer s requirements of either specifications or large quantity. Concealed Damage Any evidence of damage to goods shipped, upon the opening of the original shipping package, must be reported to the Summers Rubber Company without delay. Delivery Delays Summers Rubber Company shall not be liable or deemed in default for failure to deliver or delay in delivery due to any cause beyond its reasonable control. Installation Unless otherwise agreed in writing by Summers Rubber Company, Buyer and only Buyer shall be responsible for the installation and start-up of the goods. Repairs Unless otherwise agreed in writing by Summers Rubber Company, repairs to Buyer s goods are at the sole cost and expense of Buyer. PERMISSIBLE VARIATIONS Summers Rubber Company has the right, without giving notice to Buyer, prior to the delivery of goods to Buyer to make any changes in the composition of the goods which, in the opinion of Summers Rubber Company, does not affect the general characteristics or properties of the goods. In addition, Summers Rubber Company may make any change or variation in the goods which is within governmental or industry standards or specifications applicable at the time of manufacture without giving notice to Buyer. Buyer will accept any goods which may incorporate any changes in the composition or specifications, and any increase in price resulting from such change will be paid by Buyer. 9

10 CAUTIONARY STATEMENT Summers Rubber Company s Cautionary Statement All goods sold or distributed by Summers Rubber Company are in the nature of commodities and are sold under the manufacturers published specifications and not for particular purposes, uses or applications. The Buyer or user of the goods shall first determine the suitability of the goods for the intended purposes, uses or applications, and the Buyer or user of the goods shall either conduct their own engineering studies or tests, or retain and consult with qualified engineers, consultants or testing laboratories before determining the proper use, suitability or propriety of the goods for the intended purposes, uses, or applications. The Buyer or user assumes full responsibility for the suitability, propriety, use and application, installation, and maintenance of the goods. Buyer or user is responsible for disclosing, prior to sale or supply of the goods, the specifications or requirements for the goods being purchased. The goods, including but not limited to, hose, tubing or coupling may fail due to the use or conveyance of substances at elevated or lowered temperatures or at excessive pressures, or the conveyance of abrasive, injurious, flammable, explosive or damaging substances, or for other reasons related to the application, installation, use, or maintenance of the goods. Hose or tubing used in bent configurations will be subjected to increased stress and abrasion. Hose clamps or couplings may loosen after initial installation and all sections of hose and tubing, including connections, couplings and clamps, should be inspected frequently, regularly and consistently, and should be replaced, adjusted or retightened for the avoidance of leakage, for the prevention of injuries or damages, and for general safety purposes. Except as indicated in the following Limited Warranty, Summers Rubber Company shall not be liable or responsible for direct or indirect injuries or damages caused by or attributed to the failure or malfunction of the goods sold or distributed by it. Summers Rubber Company recommends that the Buyer or users of the goods frequently and consistently undertake inspections and protective measures with respect to the use and application of the goods which should include the examination of tube and cover conditions, of the hose or tubing, and the identification, repair or replacement of sections showing cracking, blistering, separations, internal and external abrasions, leaking or slipped couplings or connections, and undertake appropriate integrity and application tests. LIMITED WARRANTY, WARRANTY DISCLAIMERS AND LIMITATIONS OF REMEDIES AND LIABILITIES Summers Rubber Company warrants that the goods manufactured by Summers Rubber Company will be free from defects in materials and workmanship at the date of tender of delivery of the goods. No item shall be deemed defective if such item conforms to approval models, samples, test runs, or previously accepted items or if such item fits Buyer s products, parts, jigs, or equipment or otherwise reasonably accommodates Buyer s instructions or intended purpose. Summers Rubber Company does not warrant against failures caused by erosion, corrosion, misuse or improper use, including but not limited to any operation beyond rated capacity, improper use or application of the goods, use of the goods not in compliance with service manuals and instructions, use of the goods by untrained or unqualified persons, substitution of parts or any alteration or repair by others which, in the judgment of Summers Rubber Company, adversely affects the goods. To the extent transferable, Summers Rubber Company shall pass on to Buyer all manufacturer or supplier warranties of the goods obtained by Summers Rubber Company. Except as set forth above, Summers Rubber Company makes NO OTHER WARRANTIES concerning the goods whatsoever. SUMMERS RUBBER COMPANY DISCLAIMS AND EXCLUDES ALL OTHER EXPRESS WARRANTIES AND ALL IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE concerning the goods. Buyer acknowledges and agrees that Summers Rubber Company s obligation described in this Paragraph is the sole remedy bargained for by Buyer IN LIEU OF ALL OTHER EXPRESS AND IMPLIED WARRANTIES. In no event will Summers Rubber Company s liability exceed the paid purchase price of the goods. Summers Rubber Company s obligations described in this Paragraph shall be BUYER S SOLE AND EXCLUSIVE REMEDY AGAINST SUMMERS RUBBER COMPANY FOR ANY LIABILITY WITH RESPECT TO THE EQUIPMENT WHETHER ANY CLAIM FOR RECOVERY IS BASED UPON OR ARISES OUT OF THEORIES OF CONTRACT, NEGLIGENCE, TORT (INCLUDING STRICT LIABILITY) OR OTHERWISE. Buyer agrees that NO OTHER REMEDY SHALL BE AVAILABLE to Buyer and that IN NO EVENT SHALL SUMMERS RUBBER COMPANY BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES, including without limitation loss of income, loss of time, loss of sales, cost or replacement items, claims asserted by Buyer s customers, injury to personal property, or injury to any person, whether or not occasioned by Summers Rubber Company s negligence. No accommodation by Summers Rubber Company to Buyer, whether by attempt, effort or promise to repair or replace, and whether for sales policy or otherwise shall establish any additional liability of Summers Rubber Company or any contract term inconsistent with the terms herein. A suit based on any cause of action must be commenced within one () year from the date of delivery. 0

11 S.T.A.M.P.E.D. WORKSHEET 8 Easy Steps to Selecting a Hose Work Sheet S T SIZE Inside Diameter Length TEMPERATURE Highest Lowest Outside Diameter A M P APPLICATION How is hose being used Environmental or Installation considerations MEDIA What is going through the hose PRESSURE Actual Working Pressure (+) Spikes Suction ( ) E D ENDS Fittings Size DELIVERY Date Required Ship Via Thread Style Material Next, call your nearest Summers location. Our trained sales staff will gladly help select the right hose for your application! Company Name Contact Person Phone Number Photocopy for additional copies.

12 CREDIT APPLICATION Credit Application Company Name MAILING: Address P.O. Box City State Zip Phone No. Fax No. SHIPPING: Address P.O. Box City State Zip Phone No. Fax No. Nature of Business Bank Years in Business Branch Taxable: Yes No If exempt, include exemption certificate. Name of Buyer Phone No. Name of Owner or Principle Officer Title Signature Date How did you hear about us? Trade References. Company Phone No. Address Fax No. City State Zip 2. Company Phone No. Address Fax No. City State Zip. Company Phone No. Address Fax No. City State Zip Summers Rubber Company accepts the following credit cards as a Value-Added service for our customers. 2

13 INDUSTRIAL HOSES Multi-Purpose Hoses Red Cover General Service 200 psi, Air and Water Nom. Nom. Max. Min. Bend I.D. O.D. W.P. Suction Radius (In.) (In.) (psi) (In. Hg.) (In.) Red Red Red Red Red Red Recommended for: Air and water applications requiring maximum flexibility. Outstanding resistance to heat and ozone. Temperature range: -40 F to +200 F (-40 C to +9 C) continuous service. Construction: Tube: Type P (EPDM). Black. Reinforcement: Synthetic, high tensile textile cord. Cover: Type P (EPDM). Red. All sizes through 2 are perforated. (Blue, green and yellow covers available on special order.) Black Cover General Service 200 psi, Air and Water Nom. Nom. Max. Min. Bend I.D. O.D. W.P. Suction Radius (In.) (In.) (psi) (In. Hg.) (In.) Black Black Black Black Black Black Black Black Recommended for: Air and water applications requiring maximum flexibility. Outstanding resistance to heat and ozone. Temperature range: -40 F to +200 F (-40 C to +9 C) continuous service. Construction: Tube: Type P (EPDM). Black. Reinforcement: Synthetic, high tensile textile cord. Cover: Type P (EPDM). Black. All sizes through 2 are perforated. Tufflex GP PVC General Purpose 00 psi, Air, Water, Mild Chemicals, Mild Oils Nom. Nom. Max. Min. Bend I.D. O.D. W.P. Suction Radius (In.) (In.) (psi) (In. Hg.) (In.) Tufflex GP Tufflex GP Tufflex GP Tufflex GP Tufflex GP Tufflex GP Tufflex is a registered trademark of The Gates Rubber Company. Recommended for: Multi-purpose applications including air, water (up to0 F), mild chemicals and spray solutions at rated working pressures listed. Suitable for in-line oiler service. Silicone free. Temperature range: - F to +0 F (-26 C to +66 C) continuous service. Construction: Tube: Type G (PVC). Black. Reinforcement: Synthetic, high tensile textile cord. Cover: Type G (PVC). Red. All sizes are perforated. (Blue cover available on special order.)

14 INDUSTRIAL HOSES Multi-Purpose Hoses continued Premo Flex (Non-Conductive) 00 psi, Air, Water, Oil and Gas Nom. Nom. Max. Min. Bend I.D. O.D. W.P. Suction Radius (In.) (In.) (psi) (In. Hg.) (In.) Recommended for: Applications requiring a premium grade spiral hose with excellent flexibility and maximum resistance to air, water, petroleum oils, gasoline, kerosene and fuel oil (to 20 F) and lubricating oils (to 22 F). Excellent weather and ozone resistance. Temperature range: -40 F to +22 F (-40 C to +00 C) continuous service. Construction: Tube: Type C (Nitrile). Black. Reinforcement: Synthetic, high tensile textile cord. Cover: Type C2 (Modified Nitrile). Red. (Black, blue, green and yellow covers available in popular sizes on special order) Premo Premo Premo Premo Premo Premo 20 Premo Flex is a trademark of The Gates Rubber Company. Terminator Gorilla Type Hose (Non-Conductive) 00 psi, Oil, Weather and Ozone Resistant Nom. Nom. Max. Min. Bend I.D. O.D. W.P. Suction Radius (In.) (In.) (psi) (In. Hg.) (In.) Recommended for: Applications requiring a premiumquality, multi-purpose hose with superior abrasion resistance for air, oil and some chemical applications. Excellent durability for extra long life in these applications: mining, air drill, construction, poultry plants and other severe service. Excellent weather and ozone resistance. Temperature range: -40 F to +22 F (-40 C to +00 C) continuous service. Construction: Tube: Type C (Nitrile). Black. Reinforcement: Synthetic, high tensile cord. Cover: Type C2 (Carboxylated Nitrile). Yellow Terminator Terminator Terminator Terminator Terminator Terminator Terminator Terminator Terminator is a registered trademark of The Gates Rubber Company and Gorilla is a trademark of Goodyear Tire and Rubber Company. 4

15 INDUSTRIAL HOSES Multi-Purpose Hoses continued Clear Braided Tubing Non-toxic, FDA Approved, Resistance to Abrasion Nom.. Nom. Max. I.D. O.D. W.P. (In.) (In.) (psi) KB KB KB KB KB KB KB KB KB KB KB-2 Recommended for: Tubing is non-toxic, it can be used for food handling and other general industrial service applications such as pressurized air and water lines. It s ideal where resistance to abrasion is required. Features Meets FDA standards. Reinforced with braided, high tensile polyester yarn. Smooth inner bore provides full flow characteristics. Transparent for visual inspection. Lightweight and flexible, easy to handle. Four times the pressure rating of non-reinforced vinyl tubing. Size range: 4 I.D. through 2 I.D. Clear Vinyl Tubing (CVT) Non-toxic, FDA Approved Nom.. Nom. Max. I.D. O.D. W.P. (In.) (In.) (psi) CVT CVT CVT CVT CVT CVT CVT CVT CVT CVT CVT CVT CVT CVT-2 CVT vinyl tubing is a specially formulated flexible tubing designed for applications that require compliance with FDA and -A Sanitary Standards. CVT tubing is ideal for piping applications in the food and beverage industry since it is non-toxic. A mirror-smooth bore prevents interior buildup, is easy to clean, provides good flow characteristics, and permits visual checks on material flow. CVT tubing can be used in many industrial applications, such as low-pressure air and water lines, liquid feed lines, or transfer of various materials for permanent or temporary installations. CVT tubing s resistance to chemicals gives good to excellent service with organic and inorganic acids and alkalies, and moderate resistance to oil, gasoline, and alcohol. Features Manufactured from ingredients approved by the FDA. Meets -A Sanitary Standard for handling milk and dairy products. Transparent for visual inspection. Odorless will not affect the taste of products being handled. Ozone and age resistant. Smooth inner bore prevents accumulation of sediment. Flexible, easy to handle.

16 INDUSTRIAL HOSES Multi-Purpose Hoses continued Push-On/Lock-On 00 psi Hose I.D. Black Blue Green Red Yellow Gray (In.) Cover Cover Cover Cover Cover Cover Recommended for: Petroleum-base hydraulic oils, water, hot lubricating oils, diesel fuels and air. Lock-On hose and couplings are not recommended for pressure surge applications or critical applications, such as permanent piping in residential or commercial buildings. Use clamp for non critical vibration and diesel fuel applications. Temperature range: -40 F to +22 F (-40 C to +00 C). Air -40 F to +60 F (-40 C to +7 C). Construction: Tube: Black, oil resistant synthetic rubber highly resistant to oil and heat. (Nitrile). Reinforcement: One fiber braid. Cover: Oil and abrasion resistant synthetic rubber (Neoprene). Available in black, blue, green, red, yellow, gray and white colors. All sizes and colors meet U.S. MSHA 2G. 6 LOLA+ LOLB+ LOLG+ LOLR+ LOLY+ LOLC+ 4 4LOLA+ 4LOLB+ 4LOLG+ 4LOLR+ 4LOLY+ 4LOLC+ 8 6LOLA+ 6LOLB+ 6LOLG+ 6LOLR+ 6LOLY+ 6LOLC+ 2 8LOLA+ 8LOLB+ 8LOLG+ 8LOLR+ 8LOLY+ 8LOLC+ 8 0LOLA+ 0LOLB+ 0LOLG+ 0LOLR+ 0LOLY+ 0LOLC+ 4 2LOLA+ 2LOLB+ 2LOLG+ 2LOLR+ 2LOLY+ 2LOLC+ 6

17 INDUSTRIAL HOSES Air Hoses Contractors Air CPLD x 0 20 psi, Heavy-Duty, Universal Fittings Each End Size Working Pressure (In. x Ft.) (psi) 4 x 0 20 CAH0C Contractors Air hose is designed for heavy-duty construction applications. Working pressure: 20 lbs. Branding: White ink: Size-WP-Made in U.S.A. Cover color: Red. Oil resistance: Limited. Construction: Tube: EDPM. Reinforcement: 4 Spiral Polyester Yarn. Cover: EPDM. Nylon Recoil Hose Assemblies Hose Hose Swivel Working I.D. Length Male Length (In.) (Ft.) NPT (Ft.) No Self Storing Air Tool Hose Features Extremely lightweight. Resistant to most chemicals. Highly flexible nylon. Less than % moisture absorption. Excellent memory and coil retractability. More abrasion resistant than rubber hose. Brass swivel compression fittings both ends, prevents hose from twisting and tangling. Specifications: Recommended working length: Maximum 80% of total length. Temperature range: -20 F to +80 F (-29 C to +82 C). Working pressure: 200 psi (280 psi Heavy Duty only). Range of coil sizes: 8 to 4. 7

18 INDUSTRIAL HOSES Air Hoses continued 8MB Air Drill Wire Braid 00 psi, Extra Heavy-Duty Nom. Nom. Max. Min. Bend I.D. O.D. W.P. Suction Radius (In.) (In.) (psi) (In. Hg.) (In.) Recommended for: Extra heavy-duty, high pressure use on industrial, construction and pneumatic mining applications requiring wire braided hose with an oil resistant tube and abrasion resistant cover. Temperature range: -0 F to +22 F (-4 C to +00 C) continuous service. Construction: Tube: Type A (Neoprene). Black. Reinforcement: Braided, high tensile steel wire. Cover: Type D (Natural Rubber). Gray with yellow spiral stripe. All sizes through 4 are perforated MB MB MB MB MB Bull Hose 9MB High Pressure 000 psi, Air, Oil and Hot Water Nom. Nom. Max. Min. Bend I.D. O.D. W.P. Suction Radius (In.) (In.) (psi) (In. Hg.) (In.) Recommended for: High pressure air, water and oil applications requiring good kink resistance and excellent flexibility. Also washdown service to 22 F (00 C) in packing plants where a nonmarking cover is required. Additionally, it can convey maximum 00 psi steam at 8 F (70 C). Temperature range: -40 F to +22 F (-40 C to +00 C) air service. Construction: Tube: Type A (Neoprene). Black. Reinforcement: Braided, high tensile steel wire. Cover: Type M (Hypalon). Gold. All sizes are perforated. 4.6, MB 8.77, MB 2.92, MB 4.2, MB 4.46, MB 4.7, MB 2.94, MB , MB 8

19 INDUSTRIAL HOSES Water Hoses Black Municipal and Contractors Water Hose CPLD 0 psi, GHT Male x Female Sanitary/Hot Water Wash Down Hose 20 psi Recommended for: Water hoses provides general water pressure service for municipalities and the general construction markets. Heavy-duty, crush proof solid brass couplings with wrench grips. Cover color: Black. Oil resistance: Limited. Construction: Tube: EPDM. Reinforcement: 2 spiral polyester yarn. Cover: EPDM. Size W.P. (In. x Ft.) (psi) 4 x 0 0 CWH0C Rubber Vinyl Garden Hose Features Super strong dual spiral knit reinforcement. Rubber/Vinyl formulation maintains strength in all weather. Heavy gauge green cover. Medium duty, crush proof solid brass couplings with wrench grips. Hot water up to 60 F. Size W.P. (In. x Ft.) (psi) 8 x 0 0 SS80 4 x 0 0 SS87 Dairy Non-Marking Recommended for: Designed to clean food equipment, and is used in food processing plants; features an EPDM tube and cover. The white cover resists scuffing, abrasion and cracking. The four spiral polyester reinforcement provides flexibility and makes it virtually kink-proof. Handles hot water up to 200 F at 0 psi, and is rated for working pressures up to 20 psi. Branding: Blue Ink. Made in U.S.A. Oil resistance: Limited. Construction: Tube: EPDM. Reinforcement: 4 spiral polyester yarn. Cover: EPDM. White. Nom. Nom. I.D. O.D. W.P. (In.) (In.) (psi) Wash Wash Insulated Water Nozzles SN7 Heavy-duty brass valve and adjusting nut. Hold open clip locks any spray pattern. Chrome plated all zinc body. Industrial strength nylon handle. Rubber head guard on threaded GHT front version. Handle GHT threads. Hot water up to 80 F. Thermo-Plastic Fire Hose Nozzle with Bumper FNB-GHT Series Size (In.) GHT Thread 4 FNB7GHT 9

20 INDUSTRIAL HOSES Water Suction and Discharge Hoses Water Suction/Discharge Hose Nom. Nom. Max. Min. Bend I.D. O.D. W.P. Suction Radius (In.) (In.) (psi) (In. Hg.) (In.) Recommended for: Suction hose used to convey water, detergents, phosphate ester hydraulic fluids and dilute solutions of acids, alkalies and glycols. Temperature range: -40 F to +80 F (-40 C to +82 C) continuous service. Construction: Tube: Type P (EPDM). Black. Reinforcement: Synthetic, high tensile textile with steel wire helix. Cover: Type D (SBR). Black with green spiral stripe Shark Shark Shark Shark Shark Shark Shark 90 SD Contractor Grade Liquid Suction and Discharge Construction, Agricultural, Cesspool/Sewer Cleaning, Plant Maintenance Recommended for: Suction and discharge of liquids in the construction, rental and agricultural industries such as agricultural chemicals, liquid fertilizers and dewatering. Temperature range: -40 F to +8 F (-40 C to +70 C) Construction: EPDM rubber, polyethylene helix, synthetic braiding, smooth bore, corrugated O.D. Features Lightweight and flexible. Rated for both suction and discharge. External helix provides for easy drag. Resistant to agricultural chemicals. Durable in construction applications. Nom. Nom. Max. Min. Bend I.D. O.D. W.P. Suction Radius (In.) (In.) (psi) (In. Hg.) (In.) SD SD SD SD 20

21 INDUSTRIAL HOSES Water Suction and Discharge Hoses continued Rubber Discharge Hose Nom. Nom. Max. Min. Bend I.D. O.D. W.P. Radius (In.) (In.) (psi) (In) Water D Water D Water D Water D Water D Pump Discharge Hose Recommended for: Water discharge in heavy-duty service requiring a compact, rugged and lightweight hose. Temperature range: -40 F to +80 F (-40 C to +82 C) continuous service. Construction: Tube: Type P (EPDM). Black. Reinforcement: Multiple plies of synthetic, high tensile textile. Cover: Type D (SBR). Black with green spiral stripe. Standard Duty PVC Lay Flat Discharge Hose Nom. Max. Bursting I.D. W.P. Pressure (In.) (psi) (psi) PVC PVC PVC PVC PVC PVC PVC Recommended for: Standard duty, water discharge for construction and agricultural applications. Temperature range: - F to +8 F (-24 C to +70 C). Construction: Braided blue vinyl. Heavy-Duty PVC Lay Flat Discharge Hose Nom. Max. Bursting I.D. W.P. Pressure (In.) (psi) (psi) HD PVC HD PVC HD PVC HD PVC HD PVC HD PVC Recommended for: Heavy-duty, water discharge for construction and agricultural applications. Temperature range: - F to +8 F (-24 C to +70 C). Construction: Braided red vinyl. 2

22 INDUSTRIAL HOSES Water Suction and Discharge Hoses continued All Synthetic Mill Hose CPLD M x F NPT Pin Lug Fitting Stationary Water Discharge Tube: Black extruded synthetic rubber. Nom. I.D. Length (In.) (Ft.) 2 0 M-0C M20-0C M2-0C 2 0 M0-0C M40-0C Heavy-Duty Armour Guard Hose 00 psi Water Discharge Recommended for: Washdown. Dewatering. Coal preparation and utility plants. Petrochemical, oil and gas drilling. Jetting and pump discharge. Storage tank cleaning. Sewer cleaning. Nom. I.D. W.P. (In.) (psi) HD AG HD AG HD AG HD AG HD AG HD AG Light-Duty 00 CL Hose Water Suction and Discharge Nom. Max. Min. Bend Vacuum I.D. W.P. Radius Rating (In.) (psi) (In.) (In. Hg.) CL CL CL Recommended for: General water suction hose. Temperature range: - F to +8 F (-24 C to +70 C). Construction: Flexible PVC, rigid PVC helix, smooth bore, corrugated O.D CL CL CL CL CL 22

23 INDUSTRIAL HOSES Water Suction and Discharge Hoses continued Nom. Max. Min. Bend Vacuum I.D. W.P. Radius Rating (In.) (psi) (In.) (In. Hg.) Heavy-Duty 2 CL Hose Suction and Discharge CL CL CL CL CL CL Recommended for: Economical heavy-duty water suction hose. Temperature range: - F to +8 F (-24 C to +70 C). Construction: Flexible PVC, rigid PVC helix, smooth bore, smooth O.D. Color: Clear or Solid Green. Extra Heavy-Duty Kanaline SR Hose Suction and Discharge Nom. Max. Min. Bend Vacuum I.D. W.P. Radius Rating (In.) (psi) (In.) (In. Hg.) KL KL KL KL KL KL KL Recommended for: Heavy-duty suction and discharge hose for use in fish suction and rental/construction pumping. Construction: Flexible PVC, rigid PVC helix, synthetic braiding, smooth bore, corrugated O.D. Temperature range: - F to +8 F (-24 C to +70 C). Features Lightweight and flexible. External helix provides for easy drag. Rated for both suction and discharge. Clear sidewall permits visual check of material flow. 00 EPDM Septic, Agricultural and Marine Hose Suction and Discharge Nom. Max. Min. Bend Vacuum I.D. W.P. Radius Rating (In.) (psi) (In.) (In. Hg.) EPDM EPDM EPDM EPDM EPDM EPDM EPDM EPDM Recommended for: Heavy-duty liquid suction hose for use in construction dewatering, liquid waste, cesspool cleaning, septic handling, agricultural applications and marine use. Temperature range: -40 F to +8 F (-40 C to +70 C). Construction: EPDM rubber, polyethylene helix, smooth bore, corrugated O.D. Features Lightweight and flexible. External helix provides for easy drag. Resistant to agricultural chemicals. 2

24 INDUSTRIAL HOSES Water Suction and Discharge Hoses continued ST 200 SFG with Static Wire Hose Suction and Discharge Nom. Max. Min. Bend Vacuum I.D. W.P. Radius Rating (In.) (psi) (In.) (In. Hg.) Recommended for: Pneumatic conveying of lightweight solids such as powders and plastic pellets. Temperature range: - F to +8 F (-24 C to +70 C). Construction: Produced entirely of compounds in compliance with FDA and -A nontoxic specifications, flexible PVC, rigid PVC helix, multi-strand copper static grounding wire, smooth bore, corrugated O.D ST 200 SFG ST 200 SFG ST 200 SFG ST 200 SFG ST 200 SFG Note: This hose was not designed for bulk handling such as unloading of rail cars. 20 HFG Food Grade Service Suction and Discharge Nom. Max. Min. Bend Vacuum I.D. W.P. Radius Rating (In.) (psi) (In.) (In. Hg.) Recommended for: Applications: Heavy-duty food grade suction hose for bottling and dairy industries. Temperature range: - F to +8 F (-24 C to +70 C). Construction: Produced entirely of compounds in compliance with FDA and -A nontoxic specifications, flexible PVC, rigid PVC helix, smooth bore, corrugated O.D HFG HFG HFG HFG HFG HFG HFG HFG Note: This hose was not designed for bulk handling such as unloading of rail cars. 0 CL Discharge Hose of Grass, Leaves, Dust and Air Recommended for: Lightweight general ducting for ventilation and grass clippings, leaves, dust and fumes. Temperature range: - F to +8 F (-24 C to +70 C). Construction: Flexible PVC, rigid PVC helix, smooth bore, corrugated O.D. Nom. Min. Bending I.D. Radius (In. ) (In.) CL CL CL CL CL CL CL 24

25 INDUSTRIAL HOSES Chemical Hoses Mustang 4HW Hose Cross-Linked Polyethylene Tube Nom. Nom. Max. Min. Bend I.D. O.D. W.P. Suction Radius (In.) (In.) (psi) (In. Hg.) (In.) HW HW HW HW HW HW HW HW Mustang is a trademark and Gatron is a registered trademark of The Gates Rubber Company. Construction: Tube: Type K (Gatron Modified Cross-linked Polyethylene). Tan. High chemical resistance. Reinforcement: Synthetic, high tensile textile with steel wire helix. Cover: Type P (EPDM). Black or green corrugated with orange spiral stripe. Blue, red, gray, tan and yellow covers available on special order. Recommended for: Tank truck, barge, ship, or storage tank transfer of a variety of chemical products. Mustang 4HW contains a wire helix for full suction capability, as well as for routing hoses through tight bends. Its Modified Cross-linked Polyethylene tube stock is best in class for maintaining a tight seal with stainless steel fittings, and is designed for cleaning with 0 psi steam or in a bath containing 0% F (00 C). Applications include over 90 basic chemicals which are building blocks for numerous chemicals used in a variety of industries. Reference The Summers Rubber Company for proper hose selection. Temperature range: -40 F to +20 F (-40 C to +2 C) normal service. Mustang 4HW is designed to withstand fluid temperatures to 20 F (2 C), however the rating is dependent on the specific chemical conveyed. Contact Summers Rubber Company for any chemical above 2 F (2 C). Solvents Aromatic Naptha Mustang Crush Resistant Hose Cross-Linked Polyethylene Tube Nom. Nom. Max. Min. Bend I.D. O.D. W.P. Suction Radius (In.) (In.) (psi) (In. Hg.) (In.) HWCR HWCR HWCR HWCR Mustang is a trademark and Gatron is a registered trademark of The Gates Rubber Company. Construction: Tube: Type K (Gatron Modified Cross-linked Polyethylene.) Tan. High chemical resistance. Reinforcement: Synthetic, high tensile textile with monofilament helix providing crush and kink resistance. Cover: Type P (EPDM). Black corrugated with orange spiral stripe. Blue, red, gray, tan and yellow covers available on special order. Recommended for: Tank truck, barge, ship, or storage tank transfer of a variety of chemical products. Mustang Crush Resistant Hose contains a wire helix for full suction capability, as well as for routing hoses through tight bends. Its Modified Cross-linked Polyethylene tube stock is best in class for maintaining a tight seal with stainless steel fittings, and is designed for cleaning with 0 psi steam or in a bath containing 0% F (00 C). Applications include over 90 basic chemicals which are building blocks for numerous chemicals used in a variety of industries. Reference The Summers Rubber Company for proper hose selection. 2

26 INDUSTRIAL HOSES Chemical Hoses continued Stallion Hose Teflon Lined Tube Nom. Nom. Max. Min. Bend I.D. O.D. W.P. Suction Radius (In.) (In.) (psi) (In. Hg.) (In.) Recommended for: Tank truck, barge, ship, or storage tank transfer of a variety of chemical products. Stallion has a wire helix for full suction capability. The Teflon tube stock has excellent chemical resistance and is backed by Gates Gatron for flex fatigue safety at the coupling. Stallion is designed for easy cleaning in a bath containing 0% F (00 C). Applications include most basic chemicals which are building blocks for numerous chemicals used in a variety of industries. Reference The Summers Rubber Company for proper hose selection. Temperature range: -40 F to +00 F (-40 C to +49 C) normal service. Stallion is designed to withstand fluid temperatures to 00 F (49 C), however the rating is dependent on the specific chemical conveyed. Contact Summers Rubber Company for any chemical above 2 F (2 C) Stallion Stallion Stallion Stallion Stallion Stallion Stallion Stallion is a trademark and Gatron is a registered trademark of The Gates Rubber Company. Teflon is a registered trademark of the Dupont Co. and Neoflon is a registered trademark of Daikin. Construction: Tube: Type T (FEP) (Teflon or Neoflon ). White backed with Gatron Modified XLPE. Reinforcement: Synthetic, high tensile textile with steel wire helix. Cover: Type P (EPDM). Blue corrugated with red spiral stripe. Stallion Crush Resistant Hose Teflon Lined Tube Nom. Nom. Max. Min. Bend I.D. O.D. W.P. Suction Radius (In.) (In.) (psi) (In. Hg.) (In.) StallionCR StallionCR Recommended for: Tank truck, barge, ship, or storage tank transfer of a variety of chemical products. Stallion Crush Resistant Hose has a wire helix for full suction capability. The Teflon tube stock has excellent chemical resistance and is backed by Gates Gatron for flex fatigue safety at the coupling. Stallion is designed for easy cleaning in a bath containing 0% F (00 C). Applications include most basic chemicals which are building blocks for numerous chemicals used in a variety of industries. Reference The Summers Rubber Company for proper hose selection StallionCR StallionCR Stallion is a trademark and Gatron is a registered trademark of The Gates Rubber Company. Teflon is a registered trademark of the Dupont Co. Construction: Tube: Type T (FEP) (Teflon or Neoflon ). White backed with Gatron Modified XLPE. Reinforcement: Synthetic, high tensile textile with monofilament helix and static wire. Cover: Type P (EPDM). Blue corrugated with red spiral stripe. 26

27 INDUSTRIAL HOSES Chemical Hoses continued Renegade Hose Ultrahigh Molecular Weight Polyethylene Tube Nom. Nom. Max. Min. Bend I.D. O.D. W.P. Suction Radius (In.) (In.) (psi) (In. Hg.) (In.) Renegade Renegade Renegade Renegade Renegade Renegade Renegade Renegade Renegade is a trademark and Gatron is a registered trademark of The Gates Rubber Company. Construction: Tube: Type L (Ultrahigh Molecular Weight Polyethylene). Clear, backed with Gatron Modified XLPE. Reinforcement: Synthetic, high tensile textile with steel wire helix. Cover: Type P (EPDM). Green corrugated with yellow spiral stripe. Recommended for: Tank truck, barge, ship, or storage tank transfer of a variety of chemical products. Renegade contains a wire helix for full suction capability, as well as for routing hoses through tight bends. The Ultrahigh Molecular Weight Polyethylene tube stock has excellent chemical resistance, and is backed by Gates Gatron for flex fatigue safety at the coupling. Renegade is designed for easy cleaning in a bath containing 0% F (00 C). Applications include over 40 basic chemicals which are building blocks for numerous chemicals used in a variety of industries. Reference Summers Rubber Company for proper hose selection. Temperature range: -40 F to +22 F (-40 C to +00 C) normal service. Renegade is designed to withstand fluid temperatures to 22 F (00 C), however the rating is dependent on the specific chemical conveyed. Contact Summers Rubber Company for any chemical above 2 F (2 C). Naptha Tallow Renegade Crush Resistant Hose Ultrahigh Molecular Weight Polyethylene Tube Nom. Nom. Max. Min. Bend I.D. O.D. W.P. Suction Radius (In.) (In.) (psi) (In. Hg.) (In.) RenegadeCR RenegadeCR RenegadeCR RenegadeCR RenegadeCR Renegade is a trademark and Gatron is a registered trademark of The Gates Rubber Company. Construction: Tube: Type L (Ultrahigh Molecular Weight Polyethylene). Clear, backed with Gatron Modified XLPE. Reinforcement: Synthetic, high tensile textile with monofilament helix and static wire. Cover: Type P (EPDM). Green corrugated with yellow spiral stripe. Recommended for: Tank truck, barge, ship, or storage tank transfer of a variety of chemical products. Renegade Crush Resistant Hose contains a wire helix for full suction capability, as well as for routing hoses through tight bends. The Ultrahigh Molecular Weight Polyethylene tube stock has excellent chemical resistance, and is backed by Gates Gatron for flex fatigue safety at the coupling. Renegade is designed for easy cleaning in a bath containing 0% F (00 C). Applications include over 40 basic chemicals which are building blocks for numerous chemicals used in a variety of industries. Reference Summers Rubber Company for proper hose selection. 27

28 INDUSTRIAL HOSES Chemical Hoses continued Colt EPDM Tube Nom. Nom. Max. Min. Bend I.D. O.D. W.P. Suction Radius (In.) (In.) (psi) (In. Hg.) (In.) Recommended for: Tank truck, barge, ship or storage tank transfer of a variety of mild chemical products. Colt contains a wire helix for full suction capability, as well as for routing hoses through tight bends. Its EPDM tube stock will withstand 20 F (2 C) applications. Reference Summers Rubber Company for proper hose selection. Temperature range: -40 F to +20 F (-40 C to +2 C) normal service. Colt is designed to withstand fluid temperatures to 20 F (2 C), however the rating is dependent on the specific chemical conveyed. Contact Summers Rubber Company for any chemical above 2 F (2 C). Construction: Tube: Type P (EPDM). Black. Mild chemical resistance. Reinforcement: Synthetic, high tensile textile with steel wire helix. Cover: Type P (EPDM). Yellow corrugated with green spiral stripe Colt Colt Colt Colt Colt Colt Colt Colt Colt Colt is a trademark of The Gates Rubber Company. 77B Paint/Chemical Hose Nom. Nom. Max. Min. Bend I.D. O.D. W.P. Suction Radius (In.) (In.) (psi) (In. Hg.) (In.) Recommended for: Paint spray applications, as well as transfer of petroleum based products (aliphatic, aromatic and chlorinated hydrocarbon; such as toluene, xylene, benzene, gasoline and carbon tetrachloride). Reference Summers Rubber Company for proper hose selection. Not Recommended for Acids. Temperature range: -40 F to +0 F (-40 C to +66 C) continuous service. Note: Contact Summers Rubber Company when conveying chemicals above 20 F (49 C). Construction: Tube: Type Z (Special flexible nylon material). Tan. Reinforcement: Synthetic, high tensile textile cord. Static wire available in 4 as special order. Cover: Type A (Neoprene). Black B* B* B* B* B* *Also available as Static Wire, minimum,000 feet. 28

29 INDUSTRIAL HOSES Chemical Hoses continued Composite Hose Products Features Lightweight easy to handle. Flexible even at low temperatures. Polypropylene liner with a polypropylene and polyester carcass for maximum chemical resistance. Abrasion-resistant PVC-coated fabric outer cover maximum durability and safety. Double end-to-end electrical continuity prevents static electricity build-up and internal arcing. Choice of galvanized or stainless steel outer wire for maximum durability depending on external environment. Couplings: Externally swaged: NPT threaded; fixed, floating, reducing flanges; cam-and-groove quick-disconnect couplings, female lugs supplied per order. Nom. Nom. Max. Min. Bend I.D. O.D. W.P. Radius (In.) (psi) (pis) (In.) COMPO PG COMPO PG COMPO PG COMPO PG COMPO PG COMPO PG COMPO PG A chemical utility hose for chemical plant, refineries, paint producers, paper mills and many other in-plant, liquid transfer operations as well as rail car loading and tank truck delivery. Recommended for: Chemical plants, refineries, paint producers, paper mills, in-plant rail car loading and tank truck delivery. Highly corrosive acids and alkalis, aldehydes, amines, alephatics, aromatic fuels, chlorinated hydrocarbons, alcohols, esters, ketones, lacquers and petroleum products at rated discharge pressure or at full suction. Not recommended for service for many bromide, chloride or fluoride compounds. Temperature range: -22 F to +22 F (-0 C to +00 C) Construction: Inner wire: Polypropylene-coated steel (6 stainless steel available). Outer wire: Galvanized steel (6 stainless steel available). Carcass: All polypropylene fabrics, films and polyester barrier layers. Cover: Abrasion-resistant PVC-coated fabric. Color: Gray with blue stripe. Teflon Tube Pure Teflon, white tube (TLCT). Unexcelled chemical resistance and compatible with all materials. Easy to clean assured sterility, can be cleaned with steam, caustics, solvents or other cleaning agents. Durable, kink resistant with no external wire reinforcement to potentially fray. Full vacuum rated and the most flexible, smooth tube Teflon design. Min. Min. Nom. Nom. Recom. Test Burst Bend I.D. O.D. W.P. Pressure Pressure Radius (In.) (In.) (psi) (psi) (psi) (In.) ,00.0 8TLCT/WTLCT , TLCT/WTLCT , TLCT/WTLCT , TLCT/WTLCT ,0.0 24TLCT/WTLCT ,200. 2TLCT/WTLCT , TLCT/WTLCT , TLCT/WTLCT , TLCT/WTLCT Teflon is a registered trademark of the DuPont Co. Temperature range: -40 F to +0 F (-40 C to +77 C). Hose has successfully passed internal steam tests at 406 F (208 C). Construction: Smooth tube internally bonded to a rubber hose type construction. Multiple reinforcement, double helix wire supported. Chemically resistant, ozone and abrasion resistant cover. Approvals: FDA (Food and Drug Administration) and Pharmacopeia Class VI. Fittings: Over 6 styles of stocked crimp design. Bolt-on or clamped fitting styles optional. 29

30 INDUSTRIAL HOSES Petroleum Hoses Longhorn Hose Petroleum Transfer Hose Nom. Nom. Max. Min. Bend I.D. O.D. W.P. Suction Radius (In.) (In.) (psi) (In. Hg.) (In.) Recommended for: Commercial gasolines, diesel oils, fuel oils and other petroleum products. Ideal for oil field service truck use. Temperature range: -40 F to +80 F (-40 C to +82 C). Note: Fuels are normally conveyed below 20 F (49 C). Construction: Tube: Type C (Nitrile). Black. Reinforcement: Synthetic, high tensile textile with steel wire helix. Cover: Type A (Neoprene). Black with red spiral stripe Longhorn Longhorn Longhorn Longhorn Longhorn Longhorn Longhorn Longhorn Longhorn is a registered trademark of The Gates Rubber Company. Tank Truck Hose Alcohol Hose Ant Freeze Hose Gasoline Hose Super-Vac Hose Oil Field Suction and Discharge Hose Nom. Nom. Max. Min. Bend I.D. O.D. W.P. Suction Radius (In.) (In.) (psi) (In. Hg.) (In.) Recommended for: Tank truck service, including oil field vacuum truck, where full suction or rated working pressures are required. Ideal for applications handling crude oil, salt and fresh water, tank bottoms, drilling mud, dilute solutions of hydrochloric acids and diesel fuels. Reference The Summers Rubber Company for chemical resistance information. Note: Not recommended for refined petroleum products such as gasoline. Temperature range: -40 F to +0 F (-40 C to +66 C) continuous service. Note: Diesel fuel normally conveyed below 20 F (49 C). Construction: Tube: Type C (Nitrile). Black. Reinforcement: Synthetic, high tensile textile with steel wire helix. Cover: Type D (SBR). Black corrugated with blue spiral stripe SuperVac SuperVac SuperVac SuperVac SuperVac SuperVac Super-Vac is a registered trademark of The Gates Rubber Company. 0

31 INDUSTRIAL HOSES Petroleum Hoses continued Wagon Master Hose Fuel Delivery Hose Nom. Nom. Max. Min. Bend I.D. O.D. W.P. Suction Radius (In.) (In.) (psi) (In. Hg.) (In.) WagonM WagonM WagonM WagonM Wagon Master is a registered trademark of The Gates Rubber Company. Diesel Hose Recommended for: Transferring fuel oils or commercial gasolines in applications at temperatures as low as -40 F (-40 C). Hose remains flexible to -20 F (-29 C). For home and commercial service where a nonmarking cover is required. Temperature range: -20 F to +80 F (-29 C to +82 C) continuous service. Note: Gasoline is normally conveyed below 20 F (49 C). Construction: Tube: Type C (Nitrile). Black. Reinforcement: Braided, high tensile synthetic textile cord. Cover: Type C 2 (Modified Nitrile). Red. Nonmarking. LPG Hose Butane-Propane Nom. Nom. Max. Min. Bend I.D. O.D. W.P. Suction Radius (In.) (In.) (psi) (In. Hg.) (In.) LPG LPG LPG LPG Power Grimp is a registered trademark of The Gates Rubber Company. Recommended for: Liquid or gaseous propane, butane or any combination of these two mixtures. Can be used for natural gas under certain conditions such as: open/outside areas and well ventilated factory buildings (if local building codes permit). Not recommended for residential or office buildings. Temperature range: -40 F to +0 F (-40 C to +66 C) continuous service. Reference The Summers Rubber Company for additional information. Construction: Tube: Type C (Nitrile) up to 4. Type A (Neoprene) 2, 2 and. Black. Reinforcement: Braided, high tensile synthetic textile cord. Cover: Type C 2 (Modified Nitrile). Up through 4. Type A (Neoprene) 2, 2 and. Black. All sizes are perforated. Couplings: 72 Gates permanent Power Crimp couplings only through 2 I.D.

32 INDUSTRIAL HOSES Petroleum Hoses continued Vapor Recovery Hose Nom. Nom. Min. Bend I.D. O.D. Radius (In.) (In.) (In.) Recommended for: Gasoline vapor recovery only. Temperature range: -40 F to +8 F (-40 C to +70 C). Construction: Nitrile rubber, rigid PVC helix, smooth bore, corrugated O.D VaporRec VaporRec VaporRec Gasoline Drop Hose Nom. Nom. Max. Min. Bend I.D. O.D. W.P. Radius (In.) (psi) (pis) (In.) LT LT Recommended for: Gasoline tank truck gravity drop hose for such items as naphtha, kerosene, light and heavy oil, and gasohol. Temperature range: -0 F to +8 F (-4 C to +70 C). Construction: Nitrile rubber, rigid PVC helix, synthetic braiding, smooth bore, corrugated O.D. Features Lightweight and flexible. External helix provides for easy drag. Rated for up to 40% aromatic content. Available with static grounding wire: ST20 LT. Note: Banding sleeves must be used for and 4 sizes ST20LT ST20LT ST20LT 2

33 INDUSTRIAL HOSES Steam/Pressure Washer Hoses Steam Hose Nom. Nom. Max. Min. Bend I.D. O.D. W.P. Suction Radius (In.) (In.) (psi) (In. Hg.) (In.) Black Cover Steam Steam Steam Steam Steam Steam Steam Red Cover RedSteam RedSteam RedSteam Recommended for: All types of steam saturated and superheated up to 20 psi and 40 F (22 C). Note: Do not alternate use between steam and water. Temperature range: 40 F to +40 F (-40 C to +22 C) continuous service. Construction: Tube: Type P 2 (EPDM). Black. Reinforcement: Braided, high tensile steel wire. Cover: Type P 2 (EPDM). Black or red. All sizes are perforated RedSteam RedSteam Whitewater Pressure Washer and Steam Cleaner Hose Combination Hose Nom. Nom. Max. Min. Bend I.D. O.D. W.P. Suction Radius (In.) (In.) (psi) (In. Hg.) (In.) For Service to 20 F (2 Pressure 8.690,000 2, WhiteW 2.8 2,00 0, WhiteW For Service to 2 F (6 Pressure , WhiteW , WhiteW Recommended for: Designed for use on either steam cleaner machines or combination steam cleaner/pressure washer machines. Resistant to Cleaning Chemicals. The tube and cover compounds used in Goodyear Whitewater hose are resistant to the chemicals used in the pressure washer and steam cleaner market. Temperature ranges: Handles steam safely. Whitewater handles steam up to 2 F (6 C) at 0 psi with a safety factor in excess of 0 to. Handles high pressure hot water. Whitewater handles hot water up to 20 F (2 C) at 000 psi (200 psi on 2 ) with a 4 to safety factor. Construction: Tube: Black heat resistant synthetic rubber. Reinforcement: One wire braid. Cover: Black heat and ORS synthetic rubber (pin pricked), RMA Class B.

34 INDUSTRIAL HOSES Steam/Pressure Washer Hoses continued PCI Power Clean Pressure Washer Hose 000 psi PCII Power Clean Pressure Washer Hose 4000 psi Recommended for: Heavy-duty use on hot and cold water high pressure cleaning equipment where heavy-duty service is required. Flexible. Use Bend Restrictors to extend service life. Note: Not recommended for steam service. Temperature range: Laboratory tested for normal service from -40 F to +22 F (-40 C to +00 C). Increased operating temperatures will reduce hose assembly service life. Construction: Tube: Black. Specially compounded to handle high pressure water service. Reinforcement: High tensile steel one-wire braid. Cover: Black. Specially compounded to handle pressure washer environment. Nom. Nom. Max. Min. Bend I.D. O.D. W.P. Suction Radius (In.) (In.) (psi) (In. Hg.) (In.) 4.8,000 2, PCI 8.68,000 2, PCI ,00 0, PCI Recommended for: Heavy-duty use on hot and cold water high pressure cleaning equipment where heavy-duty service is required. Flexible. Use Bend Restrictors to extend service life. Note: Not recommended for steam service. Temperature range: Laboratory tested for normal service from -40 F to +22 F (-40 C to +00 C). Increased operating temperatures will reduce hose assembly service life. Construction: Tube: Black. Specially compounded to handle high pressure water service. Reinforcement: High tensile steel two-wire braid. Cover: Black. Specially compounded to handle pressure washer environment. Nom. Nom. Max. Min. Bend I.D. O.D. W.P. Suction Radius (In.) (In.) (psi) (In. Hg.) (In.) 4.8,000 20, PCII ,000 8, PCII 2.86,00 4, PCII Refer to page 48 for Pressure Washer Wands and Nozzles. Crimped Steam Hose Couplings Available Female Spud Male Spud Double Spud Knurled Nut Wing Nut Dayco is a registered trademark of Mark IV, Inc. 4

35 INDUSTRIAL HOSES Material Handling Hoses Dry Material Suction/Discharge Hose Gum Tube, Bulk Commodity, FDA Approved Nom. Nom. Max. Min. Bend I.D. O.D. W.P. Suction Radius (In.) (In.) (psi) (In. Hg.) (In.) SB SB SB SB SB SB SB Recommended for: Transfer of bulk food products via suction, pneumatic or gravity systems where FDA sanitary tubestock is required. Examples: Flour, sugar, syrup and edible grains. (Not recommended for vinegar, mustard or other compounds containing acetic acid.) Temperature range: -40 F to +0 F (-40 C to +66 C) continuous service. Construction: Tube: Type D 2 (Natural Rubber). Sanitary FDA. White. 6 thick. ( 8 thick tube also available.) Reinforcement: Synthetic, high tensile textile with steel wire helix. Cover: Type D (Natural Rubber). Gray corrugated with burgundy spiral stripe. 80AR Material Handling Suction/Discharge Hose SBR Tube Nom. Nom. Max. Min. Bend I.D. O.D. W.P. Suction Radius (In.) (In.) (psi) (In. Hg.) (In.) AR AR AR AR AR AR AR AR AR Debris Collector Hose Slurry Hose Municipal Vacuum Hose Vac All Hose Recommended for: Transfer of dry bulk materials via suction, pneumatic or gravity systems where abrasion resistance is the primary requirement and a static conductive hose is needed. Can also be used for vacuum or ducting service. Temperature range: -40 F to +8 F (-40 C to +70 C) continuous service. Construction: Body: Type D (SBR). Black. Compounded for abrasion resistance and static conductivity. Reinforcement: Rigid PVC helix. Black.

36 INDUSTRIAL HOSES Material Handling Hoses continued Sand Blast Hose Nom. Nom. Max. Min. Bend I.D. O.D. W.P. Radius (In.) (psi) (pis) (In.). Recommended for: Sand, shot blasting work and wherever abrasive materials are carried at high velocity. Temperature range: -40 F to +0 F (-40 C to +66 C) continuous service. Construction: Tube: Type D (Natural Rubber). Black. Static conductive. Reinforcement: Synthetic, high tensile textile. Cover: Type D (SBR). Black with yellow spiral stripe. All sizes are perforated Sandblast Sandblast Sandblast * Sandblast* Sandblast Sandblast Sandblast *Special Nominal I.D. Sand Blast Hose. Dry Cement Delivery Hose Nom. Nom. Max. Min. Bend I.D. O.D. W.P. Radius (In.) (psi) (pis) (In.) Dry Cement Recommended for: Pneumatic transfer of bulk cement and other dry bulk materials. Temperature range: -40 F to +0 F (-40 C to +66 C) continuous service. Construction: Tube: Type D (Natural Rubber). Black. Static conductive 8 thick. ( 4 thick tube also available.) Reinforcement: Synthetic, high tensile textile. Cover: Type D (SBR). Black with gray spiral stripe. Shot Blast Hose Cement Blower Hose Blower Hose Hot Air Blower Hose Nom. Nom. Max. Min. Bend I.D. O.D. W.P. Suction Radius (In.) (In.) (psi) (In. Hg.) (In.) Recommended for: Conveying hot air up to 0 F from blower or compressor to storage tank used in the transfer of dry bulk commodities. Temperature range: -40 F to +0 F (-40 C to +77 C) normal service. Construction: Tube: Type H (Butyl). Black. Reinforcement: Synthetic, high tensile textile with steel wire helix. Cover: Type P (EPDM). Black with yellow spiral stripe HotAir HotAir HotAir 6

37 INDUSTRIAL HOSES Material Handling Hoses continued Elephant Trunk Hose Nom. Nom. I.D. O.D. Reinforce- (In.) (In.) ment plies 46 Elephant plies 6 8 Elephant plies 47 Elephant plies 7 2 Elephant plies 28 Elephant plies 8 8 Elephant plies 0 Elephant plies 0 4 Elephant plies 2 Elephant plies 2 4 Elephant plies 4 Elephant plies 6 Elephant plies 8 Elephant plies 20 Elephant plies 22 Elephant plies 24 Elephant plies 0 Elephant Recommended for: Designed exclusively for low pressure discharge service. Lightweight construction provides excellent flexibility for handling ease. Premium quality tube resists cuts, scuffs, and gouges. All-purpose cover protects against ozone attack. Temperature range: -40 F to +80 F (-40 C to +82 C). Construction: Tube: ES 97: 8 SBR. ES 98: 6 SBR. Reinforcement: Multiple plies of polyester. Cover: 6 SBR. Drop Sleeves Hose Premium Concrete Pump Hose Nom. Nom. I.D. O.D. Reinforce- W.P. (In.) (In.) ment (psi) plies ConcPump plies ConcPump plies 00 2 ConcPump plies ConcPump plies 00 2 ConcPump plies ConcPump Recommended for: Premium grade, high quality, multipurpose concrete placement hose. Specially formulated tube offers superior protection against wet, abrasive materials. Our exclusive arana design offers excellent flexibility for handling ease and is kink resistant. Rugged, abrasion resistant, all purpose cover provides excellent protection against cuts, scuffs, gouges, and ozone attack. Temperature range: -40 F to +80 F (-40 C to +82 C). Construction: Tube: Seamless SBR. Reinforcement: Multiple plies of polyester. Cover: One piece SBR. 7

38 INDUSTRIAL HOSES Material Handling Hoses continued High Pressure Grout Hose Recommended for: Ultra-high pressure, premium grade concrete pump hose. Designed specifically for high pressure applications. Our exclusive arana spiral method minimizes contraction and elongation while remaining flexible for handling ease. High grade tube provides added protection against wet, abrasive materials. All weather cover resists scuffs, cuts, gouges and is ozone resistant. Temperature range: -40 F to +80 F (-40 C to +82 C). Construction: Tube: Seamless SBR. Reinforcement: Multiple plies of polyester. Cover: One piece SBR. Nom. Nom. I.D. O.D. Reinforce- W.P. (In.) (In.) ment (psi) plies Grout plies Grout plies Grout plies Grout plies Grout Plaster Hose 4 Tube Dredge Sleeve Recommended for: Rugged abrasion resistant flexible connectors. Designed exclusively for in-line dredge discharge service. Heavy-duty construction provides excellent working pressures. Specially formulated tube offers superior protection against cuts, scuffs, or abrasions. Available in three different tube thicknesses to meet your needs. Temperature range: -40 F to +80 F (-40 C to +82 C). Construction: Tube: Black natural. Reinforcement: Multiple plies of polyester. Cover: One piece SBR. Nom. Nom. I.D. O.D. Reinforce- W.P. (In.) (In.) ment (psi) plies Dredge plies Dredge plies Dredge plies Dredge plies Dredge plies Dredge plies 0 48 Dredge plies Dredge plies 0 40 Dredge plies Dredge plies 0 2 Dredge plies Dredge plies 0 4 Dredge plies 0 4 Dredge v 8 plies 0 6 Dredge plies 0 8 Dredge Note: 8 Tube and 2 Tube also available. 8

39 INDUSTRIAL HOSES Material Handling Hoses continued Rubber Tar and Asphalt Hose Nom. Nom. Max. Min. Bend I.D. O.D. W.P. Suction Radius (In.) (In.) (psi) (In. Hg.) (In.) RT&A RT&A RT&A RT&A RT&A RT&A Crack Filler Hose Tar Patching Hose Emulsion Hose Drop Sleeves Gum Sleeves Tar and Asphalt Fittings Recommended for: Hot asphalt tank truck delivery and barge cleaning with a maximum temperature of 0 F. Temperature range: 20 F to +0 F (-29 C to +77 C). Hot asphalt. Construction: Tube: Type C (Nitrile). Black. Reinforcement: Synthetic, high tensile textile with steel wire helix. Cover: Type A (Neoprene). Black with red spiral stripe. Heavy-duty packed-on reusable rigid male to female swivel fittings ensure secure, leak-free connections in severe tar and asphalt transfer applications. These mechanically attached fittings can be easily installed at the factory or in the field. Refer to page 97 for Metal Tar and Asphalt Hose. Male Fitting with NPT Thread Swivel Female Fitting with NPS Thread Crack Filler Material Handling Hose Tan Pure Gum Tubing Wrapped Finish Nom. I.D. (In.) Wall Thickness (In.) Nom. I.D. (In.) Wall Thickness (In.) 44 6, 8, 6, , 6, 4, , 8, 6, , , 8, 4, 6, 8 8, 4 8, 6, 4, 8, 7 6, 2, 8 8, 6, 4, 6 8, 6, 4, 6, 2, , 4, 8, 2, , 4 8, 4, 2 8 8, 4 8, 4 8, 4, 8, 4 8 8, 4 Rubber tubing is available in almost any durometer or polymer. The most popular is durometer pure gum or 60 durometer Neoprene. Tubing is often used for fluid transfer, larger sizes for discharge chutes where abrasion presents problems. Available in: Neoprene EPDM SBR Nitrile Silicone 24 6, 8, 4, 6, 8, , , , 4, , 4 Available up to 42 I.D. 9

40 INDUSTRIAL HOSES Food and Beverage Hoses Food and Beverage Master Hose Nom. Nom. Max. Min. Bend I.D. O.D. W.P. Suction Radius (In.) (In.) (psi) (In. Hg.) (In.) Recommended for: Transfer of milk, juice, soft drinks, pharmaceuticals, cosmetics or water-based products requiring an FDA sanitary hose. Food Master is also suitable for many dry bulk products via suction, pneumatic or gravity where a sanitary hose is required. Temperature range: -40 F to +20 F (-40 C to +0 C) continuous service. Construction: Tube: Sanitron. White. Reinforcement: Synthetic, high tensile textile with static conductive filament; resilient monofilament helix providing crush and kink resistance Food Bev Food Bev Food Bev Food Bev Food Bev Food Bev Food Bev Food and Beverage Master and Sanitron are trademarks of The Gates Rubber Company. 20HFG Clear PVC Suction/Discharge Hose Meets FDA Requirements A Standards and USDA Nom. Nom. Max. Min. Bend I.D. O.D. W.P. Suction Radius (In.) (In.) (psi) (In. Hg.) (In.) Recommended for: Transfer of bulk food products via suction, pneumatic or gravity systems where sanitary hose is required. Temperature range: -0 F to +8 F (-2 C to +70 C) continuous service. Construction: Body: Type G (PVC). Sanitary FDA. Clear. Reinforcement: Rigid thermoplastic reinforcement HFG HFG HFG HFG HFG HFG HFG Milk Suction/Discharge Hose 40

41 INDUSTRIAL HOSES Food and Beverage Hoses continued 692SB Bulk Commodity Suction/Discharge Hose FDA Tube Fats, Oils and Acetic Acids Nom. Nom. Max. Min. Bend I.D. O.D. W.P. Suction Radius (In.) (In.) (psi) (In. Hg.) (In.) SB SB SB SB SB SB Recommended for: Animal fat, vegetable oil and other edible oils at temperatures up to 80 F requiring FDA sanitary hose. Also for soybeans, vinegar, mustard, cider, salad dressings and other acetic acid applications. Temperature range: -40 F to +80 F (-40 C to +82 C) continuous service. Construction: Tube: Type A 2 (Neoprene). Sanitary FDA. White. 8 thick. ( 8 thick tube also available.) Reinforcement: Synthetic, high tensile textile with steel wire helix. Cover: Type A (Neoprene). Tan corrugated with burgundy spiral stripe. Potable Water Hose Nom. Nom. Max. Min. Bend I.D. O.D. W.P. Suction Radius (In.) (In.) (psi) (In. Hg.) (In.) Potable Contact Summers 0 Rubber 0.0 Company9.0 4 Potable for dimensions Potable Potable Potable Potable Recommended for: Transfer of potable water, non-potable water or liquids not containing oils or chemicals from a supply ship to an offshore drilling rig or platform and for transfer applications on offshore or onshore drilling rigs or platforms; applications which require a lightweight, flexible hose with a tight bend radius and a high rated working pressure in long continuous lengths. Temperature range: -40 F to +0 F (-40 C to +66 C) continuous service. Construction: Tube: Type D 2 (Food Grade Natural Rubber). White. Reinforcement: Multiple plies of synthetic cord. Cover: Type A (Neoprene). Tan with green spiral stripe. Oil, abrasion and weather resistant. 4

42 INDUSTRIAL HOSES Food and Beverage Hoses continued Brewery Hose Nom. Nom. Max. Min. Bend I.D. O.D. W.P. Suction Radius (In.) (In.) (psi) (In. Hg.) (In.) Recommended for: Beer, ale or water based products requiring an FDA sanitary hose. Temperature range: -40 F to +20 F (-40 C to +0 C) continuous service. Construction: Tube: Sanitron. White. Reinforcement: Synthetic, high tensile textile with resilient monofilament helix providing crush and kink resistance. Cover: Type P (EPDM). White with burgundy spiral stripe. Hose Ends: Plain Brew Brew Brew Brew Brew Brew Brew Sanitron is a trademark of The Gates Rubber Company. Cellar Master Wine and Water Based FDA Hose Nom. Nom. Max. Min. Bend I.D. O.D. W.P. Suction Radius (In.) (In.) (psi) (In. Hg.) (In.) Recommended for: Wine or water-based products requiring an FDA sanitary hose. Temperature range: -40 F to +20 F (-40 C to +0 C) continuous service. Construction: Tube: Sanitron. White. Reinforcement: Synthetic, high tensile textile with resilient monofilament helix providing crush and kink resistance Cellar Cellar Cellar Cellar Cellar Cellar Cellar Cellar Master is a registered trademark and Sanitron is a trademark of The Gates Rubber Company. 42

43 INDUSTRIAL HOSES Special Application Hoses Green GP/Oxygen Hose I.D. O.D. W.P. (In.) (In.) (psi) Service XHD 8 Green OX XHD 2 Green OX XHD 4 Green OX Out Gassing Hose Scarfing Hose Recommended for: The abuse oriented applications in the steel producing and oil refining industries. It features a medium high oil resistant NBR blend tube with a four spiral polyester reinforcement. The medium oil resistant cover and a constant working pressure of 00 psi make this heavy-duty hose the ideal industrial choice. Not recommended for fuel or oil transfer applications. Branding: Yellow Ink. Size-WP-GP/Oxygen-Made in U.S.A. Cover color: Green. Oil resistance: Medium High. Construction: Tube: Medium high oil resistant, NBR blend. Reinforcement: Four spiral polyester yarn. Cover: Medium oil resistant, CR. Oxygen/Acetylene Welding and Burning Hose I.D. O.D. W.P. (In.) (In.) (psi) Weld Weld Weld Weld Recommended for: Use in the steel, metalworking, shipbuilding and construction industries. The tube is smooth and free of contaminants, which is important when welding with argon or other sensitive gases. The abrasion resistant cover resists cracking and weather. Multi-spiral reinforced construction makes the hoses extremely flexible and easy to handle in cramped spaces. They are virtually kink-proof and crush-proof. Both hoses are available in R, RM or T grades, and exceed RMA/CGA requirements. Branding: White per RMA requirements. Cover colors: Single and twin line. Cover colors: Red for fuel gas. Cover colors: Green for oxygen. Cover colors: Other colors available. 4

44 INDUSTRIAL HOSES Special Application Hoses continued Marine Exhaust Hose Discharge Coolant and Marine Hose Wire Inserted Suction and Discharge Recommended for: Use as a straight connection in wet exhaust systems on marine gasoline or diesel engines. It is the top-of-the-line marine exhaust hose and is multi-plied soft wall hose. Temperature range: 0 to +22 F (-8 C to +00 C). Length: Available in 2 lengths. Construction: Tube: Blended for coolant and heat resistance. Carcass: Multiple plies synthetic fabric. Cover: Blended for oil, heat and ozone resistance. I.D. O.D. W.P. (In.) (In.) (psi) Marine Marine Marine Marine Marine Marine Marine Marine Marine Marine Marine Marine Marine Marine Marine Marine Marine Marine Marine Marine Marine Marine Marine Marine Marine Marine Marine Marine Marine Marine Marine Marine Marine Marine Marine Marine Marine Marine Recommended for: Multi-purpose application where wire reinforcement is required to resist vacuum or where a wire reinforced hose is required to provide great flexibility and resists kinking including: bilge ventilation, bilge pump intake and discharge, toilet and bath connections, cabin heating and internal water systems, galleys and drains. Temperature range: -20 to +22 F (-29 C to +00 C). Length: 2 and 60 most sizes. Construction: Tube: Blended for coolant and heat resistance. Cover: Blended for oil, heat and ozone resistance. Specifications: Flexible, wire reinforced hose for automotive, industrial and marine applications. One ply synthetic fabric through 2 4 I.D., two-ply 2 8 and over. I.D. O.D. Burst Min. Bend (In.) (In.) (psi) Radius (In.) WI Marine WI Marine WI Marine WI Marine WI Marine WI Marine WI Marine WI Marine WI Marine WI Marine WI Marine WI Marine WI Marine WI Marine WI Marine WI Marine WI Marine WI Marine WI Marine WI Marine WI Marine WI Marine WI Marine WI Marine WI Marine WI Marine WI Marine WI Marine WI Marine 44

45 INDUSTRIAL HOSES Special Application Hoses continued Thermo AG 800 Agriculture Spray Hose Nom. Nom. Max. Min. Bend I.D. O.D. W.P. Suction Radius (In.) (In.) (psi) (In. Hg.) (In.) Thermo AG Thermo AG800 Thermo AG 800 is a registered trademark of The Gates Rubber Company. Spraying Hose Farm Spray Hose Orchard Spray Hose Herbicides Hose Hi Temp Hose Recommended for: Spraying lawns, trees and similar applications with diluted solutions of water and oil based insecticides and herbicides. For insecticides or herbicides containing more than 2% Toluene or Xylene. Temperature range: + F to +0 F (-26 C to +66 C). Maximum temperature dependent on insecticide/herbicide or chemical conveyed. For temperature above 20 F (49 C), contact Summers Rubber Company. Construction: Tube: Type G (PVC). Black. Reinforcement: Synthetic, high tensile textile cord. Cover: Type G (PVC). Yellow. Nom. Nom. Max. Min. Bend I.D. O.D. W.P. Suction Radius (In.) (In.) (psi) (In. Hg.) (In.) HB Divers Air Hose 8.7, HB 2.94, HB Recommended for: Handling mixtures of oxygen, helium and nitrogen gases customarily used in diving applications as air breathing hose. The kink resistant hose is designed for extra long wear under normal operating use. Temperature range: -40 F to +20 F (-40 C to +49 C) continuous service. Construction: Tube: Type C (Nitrile). Black. Reinforcement: Braided, high tensile synthetic textile cord. Cover: Type A (Neoprene). Black. All sizes are perforated. Industrial Furnace Coolant Hose (Non-Conductive) I.D. No. of W.P. (In.) Plies (psi) IFC IFC IFC IFC IFC Available up to 4 Recommended for: To resist sparks, flames and molten splatter in an industrial setting. It has multiple carcass with special temperature resistant outer jacket. 4

46 INDUSTRIAL HOSES Special Application Hoses continued Air Brake Hose I.D. O.D. Burst (In.) (In.) (psi) Air Brake Air Brake Recommended for: Conveying air in truck brake systems. Trailer and brake system manufacturers, and aftermarket packagers and wholesalers use this hose. It is certified to meet DOT FMVSS 06 requirements. The SOR tube and cover with a four spiral polyester reinforcement make it virtually kink-proof and keep it flexible even in extreme temperatures. Branding: KX Air Brake Size A SAE, J402 DOT KX size (MM) All Date Shift Lot Suffix. Cover color: Black. Oil resistance: Medium. Construction: Tube: SOR (Synthetic Oil Resistance Compound). Reinforcement: 4 spiral polyester yarn. Cover: SOR. Silicone Heater Hose I.D. (In.) Recommended for: Low pressure coolant and heater connections in hostile engine environments. Resists aging, ozone, chemicals, lubricants, hardening and cracking. Supplied to most major OEM s. Temperature range: -6 to + F (-4 C to +7 C). Meets or exceeds all the operating requirement of SAE J20 as well as OE specs. Specifications: Ply silicone heater hose. Nylon reinforced. NOMEX reinforcement by special order. Note: Special hose clamps are recommended on all silicone coolant and heater hose. NOMEX is a registered trademark of the DuPont Co. Hi Temp Hose

47 INDUSTRIAL HOSES Special Application Hoses continued Piranha Factory Couple Assembly Sewer Cleaning Hose NP-6 SP-6 Min. Max. Min. Bend Cover Hose I.D. O.D. W.P. Burst Radius Thick- Color (In.) (In.) (psi) (psi) (In.) ness No. Yellow ,000, NP-6 Orange ,00 6, SP-6 DSM-EPP s Piranha hose is constructed to provide rugged and reliable service under even the most severe and demanding condition found in high pressure sewer cleaning. Piranha sewer cleaning hose is constructed with a polyolefin tube which provides maximum resistance to the hydrolysis commonly associated with other thermoplastic tube materials. Reinforcement with high tensile polyester fiber contributes to an exceptionally low volumetric expansion rate and eliminates loss of strength from moisture absorption. A polyetherurethane cover provides exceptional cut, abrasion and fungus resistance. And all components are bonded together to maximize fitting retention and wear resistance, and to provide a smaller minimum bend radius. Temperature range: -40 F to +22 F (-40 C to +0 C). Construction: A yellow olefin tube, single high tensile braid reinforcement. Piranha is a registered trademark of DMS Polymer. Waterblast Ultra-High Static Pressure Hose Assemblies CPLD 0 Male NPT Each End Max. Coupling Min. Bend I.D. W.P. Thread Radius (in.) (psi) Size & Type (In.) No. 8 0, NPTF.0 WB/2K06 2 0, NPTF 7.0 WB/2K08 4 0, NPTF.0 WB/2K2 4 0, NPTF 4.0 WB/2K6 Jetting Hose Recommended for: Ultra-high pressure waterblast applications. Not recommended for hydraulic applications. Temperature range: -40 F to +20 F (-40 C to +00 C) with peaks up to 20 F (20 C). Construction: Inner Tube: Seamless black synthetic rubber. Oil resistant. Reinforcement: Four spirals of high-tensile strength wire. Cover: Black synthetic rubber. Resistant to abrasion, oil, fuel and weathering. 47

48 INDUSTRIAL HOSES Special Application Hoses continued Handbuilt Specialty Hose, Handcrafted to Your Specs Convertapipe Acid Dredge Sleeves Safetyflex Sand Suction Suction Box Flexseal Connector Flexlock Connector Flexseal and Flexlock are trademarks and Convertapipe and Safetyflex are registered trademarks of HBD Industries, Inc. 48

49 INDUSTRIAL HOSES Special Application Hoses continued Handbuilt Specialty Hose, Handcrafted to Your Specs continued Straight End Capped Hose end terminates with rubber cap to protect reinforcement from contamination that would cause hose to fail prematurely. Soft Capped End Body wire reinforcement terminates short of hose end to create soft end for ease of clamping to ensure sealed fit to couplings or pipe. Flexseal End Similar to Flexlock ends for acid/corrosive or abrasive materials utilizing a steel interlocking 2# ANSI backup ring that allows rotation of hose for wear purposes without complete disassembly of line. Combination Nipple For low or medium pressure service with water, material handling and water suction. For use with straight ends. Shank Low or medium pressure air, water or general purpose in suction or discharge service. Swage with Male Pipe Threaded End/ 0# ANSI Flange Used on smooth bore oil or chemical suction and discharge hose for barge service where weight normally associated with built-in nipple is a concern. Swage coupling can terminate in male pipe threads, victaulic groove, 0-00# ANSI fixed or floating flanges. Flexlock End 2# ANSI Flange Used where rubber seal or surface is required for applications involving acid/corrosive or abrasive materials. Incorporates a solid steel backup flange for structural strength in 2-20# ANSI configuration. Fire Engine Suction Hose Used to connect fire engine suction hose to pumps. Quick Disconnect Low and medium pressure water, petroleum and chemical transfer where fast connection is desired. Reattachable Petroleum Transfer For coupling fuel oil, tank truck, LP-gas hose and aircraft fueling hose. Beaded Ends Used where rubber seal/surface is required when handling abrasive, corrosive or caustic materials. Built-In Nipple Threaded End/ 0# ANSI Flange Recommended on handbuilt hose for heavy-duty suction or discharge service where a steel pipe is integrally built into the hose end. Pipe nipple can terminate in male pipe threads, victaulic groove, 0-00# ANSI fixed or floating flanges. Length selection: From 6 oal to 00 oal selected sizes. Contact The Summers Rubber Company for your exact length requirement. Fabric reinforcement selection: Square woven: Polyester, Nylon. Tire cord: Polyester, Nylon, Kevlar. Polymer color selection: Black Green Orange Red White Blue Brown Yellow Working pressure selection: From full vacuum to 00 psi discharge. 49

50 INDUSTRIAL HOSES Special Application Hoses continued Code 940: Cryoflex Cryogenic Hose Features Maximum compatibility handles a wide range of low temperature and cryogenic conveyants. Meet IMO Gas Carrier Code depending on construction (IMO type approval for working temperatures to -8 F (-0 C) and pressures to 0 psi (0. bar). Reliability tested to industry standard 2 times rated working pressures. Durability 6 stainless steel inner and outer wires for maximum chemical and wear resistance. Fatigue resistant developed in association with leading oil and gas companies for maximum durability, safety and performance. Double end-to-end electrical continuity prevents static electricity build-up and internal arcing. Max. Min. Bend I.D. W.P. Radius (in.) (psi) (In.) No Cryoflex Cryoflex Cryoflex Cryoflex Cryoflex Cryoflex Cryoflex Recommended for: Safe transfer of fully refrigerated liquefied petroleum gases and related conveyants to -28 F (-88 C). Conveyants handled: Compatible with a wide range of low temperature fluids including the following per IMO Gas Carrier Code, Chapter XIX: Acetaldehyde, Ammonia (anhydrous), Butadiene, Butane, Butane/Propane mixture, Butylene, Diethylamine, Ethylamine, Ethyl Chloride, Methyl Acetylene/Propadiene, Methyl Bromide, Propane, Polypropylene, Propadiene, Refrigerant Gases, Vinyl Chloride. Also suitable for Liquid Ethane to -28 F (-88 C) and liquid CO 2. Nylaflow High Pressure Paint Spray Hose Nylaflow paint spray hose is sold as a finished assembly, with NPSM female swivel and spring guards on both ends. Max Min. Operating Bend I.D. O.D. Pressure Radius (In.) (In.) psi (In.) No , *4C-4* * Nylaflow 4C-4 paint spray hose comes in stock lengths of 2 ft. and 0 ft., in black or blue. Other hose sizes and custom assembly lengths are available, subject to minimum order requirements. Key Characteristics of Nylaflow Paint Spray Hose Resistant to flex fatigue. Dissipates static charge. Will not swell or degrade in contact with most paint chemicals, oils and most other solvents. Lightweight approximately half that of comparable rubber or wire hose. Highly abrasion resistant. Extremely durable. Inner tube will not chip or peel in service, reducing the possibility of system contamination. Service temperature range of 0 F (-8 C) to 200 F (9 C). Linear change ±% under typical operating pressure. O.D. smaller than comparable rubber hose without reducing the I.D., pressure rating or fluid-carrying capacity. Smooth interior seamless inner tube. All assemblies are factory tested. Nylaflow is a registered trademark of DSM Engineering Plastic Products. 0

51 INDUSTRIAL HOSES Pneumatic Tubing Nylon (Flexible) 00 Slit Pac Flexible lightweight nylon is best used in applications such as air logic systems, chemical handling and lubricant lines. Low moisture absorption. Black tubing provides reduced ultraviolet degradation. Temperature range: -60 F to +20 F (- C to +2 C). Temperature range: Continuous use: -40 F to +200 F. Excellent dimensional stability. Tube Tube Wall Min. Bend Working O.D. I.D. Thickness Radius psi (In.) (In.) (In.) No Polyurethane 00 Slit Pac Polyether based material is most flexible (9 Durometer). Resists kinks, abrasions and most chemicals. Applications include instrumentation, robotics, vacuum, fuel lines and where highly flexible tubing is required. Temperature range: -40 F to +80 F (-40 C to +82 C). Tube Tube Wall Min. Bend Working O.D. I.D. Thickness Radius psi (In.) (In.) (In.) No Polyethylene 00 Slit Pac Linear Low Density (LLDPE) Polyethylene is lightweight and more flexible than nylon. Resistant to solvents and chemicals. Applications include air logic systems, water and chemical lines. Temperature range: -00 F to +7 F (-7 C to +80 C). Tube Tube Wall Min. Bend Working O.D. I.D. Thickness Radius psi (In.) (In.) (In.) No Metric Thermoplastic Tubing Nylon Metric Tubing 2m (82 ) Slit Pac Nylon tubing is a lightweight, flexible tube with a low moisture absorption factor. It is resistant to a wide range of chemicals. For use in a variety of applications requiring low-pressure hydraulic, pneumatic and chemical transfer. Temperature range: -40 F to 200 F (-40 C to +9 C). Temperature range: Continuous use: (-40 F to +200 F) Polyethylene Metric Tubing 2m (82 ) Slit Pac Linear Low Density (LLDPE) Polyethylene tubing has superior stress-cracking resistance as determined by the ASTM Igepal stress cracking test. Resistance to a broad range of chemicals, solvents and corrosive atmospheres. More economical and more flexible than nylon. Temperature range: -00 F to +7 F (-7 C to +79 C). Tube Tube Wall Min. Bend O.D. I.D. Thickness Radius (mm) (mm) (mm) (mm) No Tube Tube Wall Min. Bend O.D. I.D. Thickness Radius (mm) (mm) (mm) (mm) No

52 Polyurethane Metric Tubing 2m (82 ) Slit Pac INDUSTRIAL HOSES Metric Thermoplastic Tubing continued Polyurethane tubing is ether based and is the most flexible of all tubing. Resists kinks, abrasions and many chemicals. Temperature range: -40 F to +80 F (-40 C to +82 C). Tube Tube Wall Min. Bend O.D. I.D. Thickness Radius (mm) (mm) (mm) (mm) No Brass Push-In Tube Fittings Male Connector Knurled Male Connector Male Elbow Tube NPT O.D. Thread Size (In.) (In.) No Tube O.D. Thread Size (In.) (In.) No. 8 0/2 UNF /2 UNF /2 UNF 6840 Female Connector Tube NPT O.D. Thread Size (In.) (In.) No O-ring Tube NPT O.D. Thread Size (In.) (In.) No

53 INDUSTRIAL HOSES Brass Push-In Tube Fittings continued Union Elbow Banjo Elbow/UNF Thread Male Swivel Branch Tee Tube O.D. (In.) No Tube O.D. Thread (In.) Type No. 8 0/2 UNF /2 UNF /2 UNF 040 Banjo Tee/UNF Thread Tube NPT O.D. Thread Size (In.) (In.) No O-ring Female Elbow Tube O.D. Thread (In.) Type No. 8 0/2 UNF /2 UNF Union Tee Tube NPT O.D. Thread Size (In.) (In.) No Swivel Elbow Tube NPT O.D. Thread Size (In.) (In.) No O-ring Male Swivel Run Tee Tube NPT O.D. Thread Size (In.) (In.) No. 8 2 x 4 2 x O-ring Tube O.D. (In.) No Straight Union Tube O.D. (In.) No

54 INDUSTRIAL HOSES Brass Push-In Tube Fittings continued Union Reducer Manifold Encapsulated Cartridge Tube Smaller O.D. Tube O.D. (In.) (In.) No Larger Smaller Tube O.D. Tube O.D. (2 Ports) (4 Ports) (In.) (In.) No Tube O.D. (In.) No * 8 620* 4 640* 8 660* *Includes optional O-ring Plug Reducer Standard Cartridge Bulkhead Union Plug Tube O.D. O.D. (In.) (In.) No Tube O.D. (In.) No Tube O.D. (In.) No Female Bulkhead 4 Elbow Tube NPT O.D. Thread Size (In.) (In.) No Plastic Plug Tube O.D. (In.) No Tube NPT O.D. Thread Size (In.) (In.) No Plastic Color Caps Overall Diameter No X X X X denotes color: 0-White, -Black, 2-Red, -Blue, 4-Green and -Yellow. 4

55 INDUSTRIAL HOSES Brass Metric Push-In Tube Fittings Male Connector Male Swivel Run Tee Union Elbow O-ring Tube BSPT O.D. Thread (mm) Size No. 4 M M Swivel Elbow O-ring O-ring Tube BSPT O.D. Thread Size (mm) (In.) No Tube BSPT O.D. Thread Size (mm) (In.) No Union Reducer Larger Smaller Tube O.D. Tube O.D. (mm) (mm) No Straight Union Tube O.D. (mm) No Tube O.D. (mm) No Union Tee Tube O.D. (mm) No Banjo Elbow Tube Thread O.D. Size (mm) (mm) No. 4 M 0200

56 INDUSTRIAL HOSES Brass Metric Push-In Tube Fittings continued Female Connector Cartridge Branch Y Tube BSPT O.D. Thread Size (mm) (In.) No Tube O.D. (mm) No Manifold Tube BSPT O.D. Thread Size (mm) (In.) No Male Swivel Branch Tee O-ring Tube BSPT O.D. Thread Size (mm) (In.) No Side Top Ports Tube Ports Tube O.D. O.D. (mm) (mm) No Union Y Bottom Top Tube O.D. Tube O.D. (mm) (mm) No Plug Tube O.D. (mm) Plastic Color Caps Overall Diameter No No X denotes color: 0-White, -Black, 2-Red, -Blue, 4-Green and -Yellow. 6

57 INDUSTRIAL HOSES Plastic Push-In Tube Fittings 60 Swivel Elbow Long Elbow Female Elbow Tube NPT O.D. Thread Size (In.) (In.) No Tube NPT O.D. Thread Size (In.) (In.) No Tube NPT O.D. Thread Size (In.) (In.) No Male Swivel Run Tee Banjo Elbow Union Elbow Tube NPT O.D. Thread Size (In.) (In.) No Tube O.D. (In.) No Tube NPT O.D. Thread Size (In.) (In.) No Union Tee Tube Tube O.D. O.D. (In.) (In.) No

58 INDUSTRIAL HOSES Plastic Push-In Tube Fittings continued Male Swivel Branch Tee Plug-In Y Plug Tube NPT O.D. Thread Size (In.) (In.) No Straight Union Tube O.D. (In.) Union Y No Plug Tube O.D. O.D. (In.) (In.) No Branch Y Tube NPT O.D. Thread Size (In.) (In.) No Tube O.D. (In.) Plastic Color Caps Overall Diameter No No X denotes color: 0-White, -Black, 2-Red, -Blue, 4-Green and -Yellow. Single Multiple Tube O.D. Tube O.D. (In.) (In.) No

59 INDUSTRIAL HOSES Nylon Recoil Air Hose Features Extremely lightweight. Resistant to most chemicals. Highly flexible nylon. Less than % moisture absorption. Excellent memory and coil retractability. More abrasion resistant than rubber hose. Brass reusable swivel compression fittings both ends, prevents hose from twisting and tangling. Specifications: Recommended working length: Maximum 80% of total length. Temperature range: -20 F to +80 F (-29 C to +82 C). Working pressure: 200 psi (280 psi heavy-duty only). Range of coil sizes: 8 to 4. Self Spiral Hose Air Tool Hose Nominal Nominal Nominal Hose Hose Hose Swivel Working Compact Outside Coil Inside Coil I.D. O.D. Length Male Length Length Diameter Diameter (In.) (In.) (Ft.) NPT (Ft.) (In.) (In.) (In.) No. Nylon Recoil Hose Assemblies (Red) *82* *80* *92* *90* * 927* * 97* *No Spring Guard. Rigid Barb Fitting. Nylon Bulk Hose (Red)

60 INDUSTRIAL HOSES Nylon Hose Fittings Reusable Compression Fitting Individual Compression Fitting Compression Fitting Components Spring Guard Begin assembly with hose end cut square. Slide nut over hose. 2. Push hose over tapered end of body past the barb.. Slide spring guard and nut over fitting body and manually engage threads. 4. Tighten nut fully with wrench to make assembly secure. Hose Pipe I.D. Thread (In.) (In.) No Compression Fitting Kits Fitting Kit for Standard Nylon Recoil Hose Hose Pipe I.D. Thread (In.) (In.) No *0802* 6 4 * 0980* 6 4 * 0900* 4 H.D *Spring not required. Rigid Barb. Swivel Barb. Hose Pipe I.D. Thread (In.) (In.) No Male Swivel Barb Fittings Hose Pipe I.D. Thread (In.) (In.) No *Rigid Fittings *040* 8 060* Splicing Union Kit Hose I.D. (In.) No *00906* * kit includes barb fitting *and clamps Hose I.D. (In.) No Nut Hose I.D. (In.) No Ferrule and Insert Hose I.D. (In.) No

61 HOSE COUPLINGS, FITTINGS, CLAMPS AND ACCESSORIES Summary Information Cam & Groove Boss Holedall Fire Hose Fittings Andrews, Boss-Lock, EZ Boss-Lock, Swaged-on and Phonograph Finish, Polypropylene, Reducing Couplers, Adapters, Gaskets, Replacement Handles, Accessories, Strap-Grip Boss and EZ-Boss Ground Joint and Washer Type Couplings, Male and LP Stems, Boss Clamps, Air Hammer Fittings, Mining Fittings, Boss /Holedall Fittings, Steam Quick Disconnects Holedall Externally Swaged and Internally Expanded Fittings, Food Grade Fittings, Holedall Petroleum Fittings, Rams, Petroleum Coupling Expanders Swing Wall Reels, Fire Hose, Expansion Ring Couplings, Wrenches, Adapters, Swivels, Nipples, Valves, Thermoplastic and Brass Nozzles, Flat Seal Couplings Air Fittings Shank Fittings Valves Pipe & Welding Fittings Air Receiver Manifold, Air King Universal Couplings, Whipchek, Dix-Lock, Dual-Lock, Aluminum Manifolds, Air Chief Quick Connects, Blow Guns, Tube Fittings, FRLs, Gauges, Bi-Metal Thermometers Menders, Nipples, Suction Couplings, Foot Valves, Strainers, Long and Short Shank Fittings, Spray Hose Couplings, Stainless Steel Fittings Ball Valves, Locking Ball Valves, Steam Valves, Mini Valves, Non- Metallic Ball Valves, Strainers, Gate Valves, Butterfly Valves, Air Valves, Safety Check Valves Weld End Fittings, Welding Nipples, Flanges, Turned Back Fittings, NPT Threaded Fittings, Sight Flow Indicators, Grooved Pipe Fittings Brass Fittings Plastic Fittings Tank Truck Fittings Maintenance & Repair Hose Stations, Garden Hose Fittings, Brass Shank Fittings, Brass Fittings, Ferrules, Crimping Tools Quick Disconnect Fittings, PVC Tubing, Tuff-Lite Nylon, Polypropylene and Kynar Hose Fittings Tight and Loose Fill Couplers and Adapters, Shank Couplings, Pipe Caps, Loose Fill Tubes, Sight Flow Indicators, Reducers and Adapters for Tank Trucks Sealants and Lubricants, Thread Tape, Test Pumps, Coupling Inserter, Lockouts, Hose Mallet, Hose Knife, Hose Tags, Hose Ties, Hose Tape, Hose Racks, Hose Reels Clamps Hydraulic Fittings Swivel Joints Miscellaneous Pinch-On, Worm Gear, Band Clamps, Strap-Grip, Single and Double Bolt Clamps, Spiral Clamps, T-Bolt Clamps, StayPut Wire Clamps, Tools and Accessories Straight Thru s, Mold Coolant Line Couplings, Hydraulic Quick Connects, Return Line Fittings, Plugs and Caps, Swivel Adapters, Hydraulic Couplings, Hydraulic Filters and Heads V-ring Type and O-ring Type Swivel Joints Expansion Joints, Control Rods and Retaining Rings 6

62 HOSE COUPLINGS, FITTINGS, CLAMPS AND ACCESSORIES Ground Joint Fittings Ground Joint Viton Seal Couplings Recommended use High pressure, steam, air, water. Recommended clamp Interlocking U-bolt. Working pressure Hose Size Design Safety (In.) W.P. Factor 2,000 psi 4 x W.P. 4 2,00 psi 4 x W.P. 2 2,00 psi 4 x W.P. 4 2,00 psi 4 x W.P. 2 2,00 psi 4 x W.P ,00 psi 4 x W.P. The Ground Joint Viton Seal Coupling provides a metal-to-metal mating area for strength plus a steam approved DuPont Viton O-ring on the stem as a secondary seal for a superior leak proof connection. The coupling passes the 000 hour MIL-H-2920 Steam Resistance Test and strict hydrostatic tests with the wing nut tightened only by hand. The O-ring fills in the dents and scratches caused by everyday wear and tear eliminating costly leaks. Machined stems eliminate leaks caused by the parting line of as cast hose ends. Viton Seal Stems are available with male and female NPT ends. NPT ends allow for easy installation of metal hose or other connections requiring a thread end instead of a hose end. All Hose Stem and Male Stems, including the cast 4, 2 and 2 are machined with a serration design. A round knurled Ground Joint Nut is available in 4 and. It is useful for applications where less bulk and a low profile is desirable. Since the coupling is tightened by hand, the nut does not need bulky handles on the wing nut. Interlocking U-Bolt Clamps Recommended use Secures hose on interlocking hose stems The Interlocking U-bolt Clamp wraps 60 around the hose and fitting creating what can be considered an adjustable ferrule. The 60 design provides superior retention. Only nine clamps are needed to cover all hoses ranging from 2 thru 2 diameters. The clamps do not crack when tightened with an air wrench and are easy to assemble since all the nuts are one one side. The Ground Joint Viton Seal Fittings are interchangeable with the old style ground joint, and U-bolt clamps interchange with most interlocking stems. STEM WING NUT VITON O-RING SPUD Viton is a registered trademark of the DuPont Co. 62

63 HOSE COUPLINGS, FITTINGS, CLAMPS AND ACCESSORIES Ground Joint Seal Couplings Female Set (with wing nut) GJF Series Female Spud GFS Series Wing Nut GN Series Viton O-ring VO Series Hose Size (In.) Hose Size (In.) 2 GJF-2 4 GJF- 4 GJF-4 4 GJF- 2 GJF GJF-8 Hose Size (In.) Steel 2 GFS-2 4 GFS- 4 GFS-4 Machined Ductile Iron 4 GFS- 2 GFS GFS-8 Hose Size (In.) Machined Ductile Iron 2 GN-2 4 GN- 4 GN-4 4 GN- 2 GN GN-8 2 VO-2 4 VO- 4 VO-4 4 VO- 2 VO VO-8 Female Set (with knurled nut) RGJF Series Interlocking Male System IMS Series Male Spud GMS Series Knurled Nut (low profile) RGN Series Hose Size (In.) Hose Size (In.) Steel 4 x 4 IMS- 4 x 8 IMS-x8 8 x 4 IMS-8x 8 x 8 IMS-8 8 x 2 IMS-8x2 4 x 2 IMS-x2 2 x 8 IMS-2x8 2 x 2 IMS-2 2 x 4 IMS-2x 4 x 2 IMS-x2 4 x 4 IMS- 4 x IMS-x4 x 4 IMS-4x x IMS-4 Machined Ductile Iron 4 x 4 IMS- 2 x 2 IMS-6 2 x 2 IMS-8 Hose Size (In.) Steel 2 GMS-2 4 GMS- 4 GMS-4 Machined Ductile Iron 4 GMS- 2 GMS GMS-8 Double Spud GDS Series Hose Size (In.) Steel 2 GDS-2 4 GDS- 4 GDS-4 4 GDS- 2 GDS GDS-8 Hose Size (In.) Steel 4 RGN- 4 RGN-4 Viton Seal Male End (Viton Seal x Male NPT) GJMS Series Hose Size (In.) Steel 4 GJMS- 4 GJMS-4 2 GJMS GJMS-8 Viton Seal Female End (Viton Seal x Female NPT) GJFS Series 4 RGJF- 4 RGJF-4 Viton Seal Hose Stem GJS Series Hose Size (In.) Steel 2 GJS-2 4 GJS- 4 GJS-4 Machined Ductile Iron 4 GJS- 2 GJS GJS-8 Interlocking Hose Mender IHM Series Hose Size (In.) Hose Size (In.) Steel 4 GJFS- Steel 2 IHM-2 4 IHM- 4 IHM-4 4 IHM- 2 IHM IHM-8 Viton is a registered trademark of the DuPont Co. 6

64 HOSE COUPLINGS, FITTINGS, CLAMPS AND ACCESSORIES Ground Joint Seal Couplings continued Single U-Bolt IC Series Whip Check Safety Cable WC Series Warning Labels LAB Series Hose O.D. Hose O.D. Hose Min. (In.) Max. (In.) Size (In.) No Double U-Bolt IC Series 2 IC-2 4 IC- Hose O.D. Hose O.D. Hose Min. (In.) Max. (In.) Size (In.) No IC-4L IC-4L IC-L IC-6L IC-6L IC-8L IC-8L Hose Size (In.) 2 WC-2 4 WC- 2 WC-4 4 WC- 2 WC WC-8 Hose Size (In.) 2 LAB- 4 LAB- 2 LAB- 4 LAB-2 2 LAB LAB-2 Miscellaneous Quick Connects Sand Blast Couplings These fittings are designed for use on Sand Blast and Cement Placing hose. Supplied with screws. Installation:. Ends of hose must be cut square to fit snug against metal end. 2. Holding hose tight to end of fitting, insert screws and turn in full, putting screw 80 from first to insure best centering.. After all screws have been placed, check tube opposite screws to be sure screws have not penetrated completely through. Threaded Couplings (Aluminum) ASC Series Quick Couplings ASB Series NPT Size (In.) 4 ASC2 2 ASC0 Hose Hose Size (In.) O.D. (In.) No ASB ASB ASB ASB0 Nozzle Holders ANH Series Hose Hose Size (In.) O.D. (In.) No ANH ANH ANH ANH0 WARNING: FOR WATER SERVICE ONLY. NOT TO BE USED FOR STEAM SERVICE. NOTE: Safety Clips are same size for both 2-lug & 4-lug Universal Couplings. Use Safety Clips on all Universal Coupling applications. 64

65 HOSE COUPLINGS, FITTINGS, CLAMPS AND ACCESSORIES Air Fittings and Accessories Air King Universal Couplings for Air Service Only (Also available in Brass, Stainless Steel) Hose End (Malleable Iron) AM Series Size (In.) 8 AMH 2 AM 8 AM 4 AM6 4 AM King 4-Lug Quick-Acting Couplings Hose End (Malleable Iron) AM Series Size (In.) Female NPT End (Malleable Iron) AM Series 4 AM6 2 AM2 2 4 AM26 Male NPT End (Malleable Iron) AM Series Size (In.) 8 AMB 2 AMB 8 AM2 4 AM7 4 AM2 Rubber Washer for 4-Lug Fits All Sizes Size (In.) 4 AM8 2 AM2 2 4 AM28 AWR4 Female NPT End (Malleable Iron) AM Series Size (In.) 8 AMC 2 AMC 8 AM 4 AM8 4 AM Air King with Ferrules AM-WF and RAM-WF Series Malleable Iron and Stainless Steel Air King with Carbon Steel Ferrules can be crimped or swaged-on. Rated to 0 psi Working Pressure. Blank End (Malleable Iron) AM Series AM0 Size O.D. Range Mall. Iron Stain. Steel (In.) From To AMWF- RAMWF AM6WF- RAM6WF AMWF AMWF- RAMWF Triple Connection (Malleable Iron) AM Series AM0 Air King Universal Swivels AM-SWIV Series These Universal Swivel fittings interchange with other Air King fittings and include a heavy-duty, free-turning joint that will swivel under pressure to prevent hose kinking. Working Pressure: 0 psi. Malleable Iron. For Air Service Only. Size (In.) 2 Male NPT AM2SWIV 4 Hose End AM6SWIV 4 Male NPT AM7SWIV 4 Female NPT AM8SWIV 6

66 HOSE COUPLINGS, FITTINGS, CLAMPS AND ACCESSORIES Air Fittings and Accessories continued The use of an Air King Safety Clip or wire type retainer is necessary to assure Air King Universal Couplings will not become accidentally disconnected. This guarantees the fittings are properly connected as pin will not go through holes in mating flanges until couplings are locked in place. Air King is rated to 0 psi Standard Air King fittings come with AWR4 washers. Air King available to meet MIL Spec. WWC-6D. WARNING: NEVER USE ANY AIR KING COUPLINGS FOR STEAM SERVICE! None of Summers Rubber Company s catalog information is to be interpreted to mean that this type of coupling is suitable for use on steam hose. The Importance of Whip Hose Constant vibration created by air drills, pavement breakers etc. is destructive to air hose couplings, especially the quickacting type. To provide protection connect one end of a to 0 length of air hose to the tool using the heat-treated No. 00 Steel Nipple which withstands vibration for a longer period. Connect the other end of Whip Hose to the air supply with the quick-acting coupling. Whip Hose should remain permanently connected to the tool and should be the same diameter as the supply line hose. Washers AWR Series Safety Clips AC Series (Package of 2) AWR4 One size fits all coupling sizes. Rubber temperature range: 20 F to 60 F. AC One size fits all coupling sizes. In-Line Lubricators PL Series Designed to protect portable or stationary air tools by efficiently oiling the tool mechanisms. Each time an air tool is operated, a fine mist of oil is injected into it along with the air from the compressor. Installation is recommended within 2 feet of the tool to be lubricated. Transparent sight disc allows visual inspection of oil level. Oil flow regulated by screwdriver screw adjustment. Size (In.) 2 PL00L 4 PL400L 4 PL400L 4 PL00L Whipchek Safety Cable WB or WA Series Use Whipchek to help prevent accidents or injury resulting from hose or coupling failure. A positive safeguard for air hose connections helps you meet today s safety standards. Whipcheck should be installed in the extended positive position (no slack). Maximium Working Pressure: 200 psi for Air. Features Hose-to-hose or hose-to-rigid outlet. Whipchek is the low cost answer to eliminate injuries caused by broken air hose connections. Highly resistant to rust and corrosion. No tools needed Easy to install and remove. Accepted by Bureau of Mines. Bureau of Reclamation. U.S. Army Corps. of Engineering. OSHA. Cable Length (In.) (In.) WB 4 8 WA2 Safety Blow Gun D Series Basic safety blow gun for general purpose use. Tip pressure will not exceed 0 psi, yet gives a good blast of air for cleaning. It complies with the requirements of OSHA lb and 90.9 when used on air lines of 0 psi or less. Safety glasses or shield must be worn when using any blow gun. 4 female NPT inlet D204-0 Rubber Tipped Blow Gun D Series Provides leakproof seal between gun and fluid line or other opening. Also excellent for cleaning molds or delicate surfaces where a metal tip might scratch or otherwise harm critical areas. CAUTION: This blow gun does not have a safety by-pass to prevent buildup of tip pressure in the event of tip blockage. It may be used for cleaning purposes only if the air supply (inlet pressure) has been reduced to 0 psi or less. TYPE OF OIL TO USE Use any petroleum-base, non-detergent lightweight oil (SAE 0/0SSU) which will readily break up into a mist. Do not use any synthetic oil or oils containing additives or solvents female NPT inlet D20

67 HOSE COUPLINGS, FITTINGS, CLAMPS AND ACCESSORIES Air Fittings and Accessories continued Ball Swivels D-S Series Hose Male Size NPT (In.) (In.) D444S 4 D446S Air Tool Swivels D-U Series Size (In.) 4 D44U 8 D46U 2 D48U Push-On Ball Swivels D-SL Series In-Line Swivels SV Series Rated to 20 psi. Steel. Minimum psi. Hose Male Size NPT (In.) (In.) D444SL 4 D446SL Hose Female Size NPT (In.) (In.) 2 x 2 SV20 4 x 4 SV26 in Manifolds D Series Suggested Applications Supply air operated tools from a single hose. Mount to pipe at workbench or overhead. Permits use of air by more than one mechanic. Different tools in the shop use different styles of couplers. Mount different style couplers on one manifold. Inlet Thread (In.) 4 NPT D404 8 NPT D406 2 NPT D408 Dixon Steel Hose Mender DM and RDM Series Shank Type Fittings Dixon Brass Hose Mender BM Series Size (In.) Zinc Plated Steel 6 Stainless Steel 4 DMA RDMA 8 DMB RDMB 2 DM RDM 8 DM 4 DM6 RDM6 4 DM RDM 4 DM6 RDM6 8 DM8 2 DM2 RDM2 2 DMXL2* 2 4 DM26 RDM DMXL26* 2 2 DM 4 DM6 RDM6 4 4 DM46 RDM46 4 DM 6 4 DM DM DM DM20 *XL series is extra long. Size (In.) 6 BSI 44 4BSI 6 BSI 84 6BSI 24 8BSI 44 2BSI 44 6BSI 67

68 HOSE COUPLINGS, FITTINGS, CLAMPS AND ACCESSORIES Shank Type Fittings continued King Combination Nipples Hose nipples, made from tubular stock, to fit straight end hose. Threaded end, in all styles, has male NPT thread same size as hose; i.e. 2 nipple has 2 thread and fits 2 I.D. hose. Combination nipples are recommended for low pressure discharge and suction service. The working pressure of combination nipples varies with the size of the nipple, the size and construction of the hose and the type of clamping system used. A coupled length of hose, in any size, should be tested to 2 times the working pressure and held for minutes without leaking or coupling movement. As a general rule, these fittings are not recommended for pressures exceeding 00 psi on hose diameters and over. Not intended for compressed air on sizes 4 and above. Unplated Steel, Plated Steel and 6 Stainless Steel NPT Ends ST, STC and RST Series Size (In.) Unplated Steel Plated Steel 6 Stainless Steel NPT End NPT End NPT End 2 ST STC RST 4 ST STC RST 4 ST0 STC0 RST0 4 ST STC RST 2 ST20 STC20 RST ST2 STC2 RST2 2 2 ST0 STC0 RST0 4 ST STC RST 4 4 ST40 STC40 RST40 4 ST0 STC0 RST0 6 4 ST60 STC60 RST ST80 STC80 RST ST00 STC ST20 STC20 Unplated steel and plated steel in sizes 2 2 are knurled. Flanged Steel FST Series Size (in.) Flanged Steel* 2 FST FST2 4 FST 4 4 FST FST FST80 * are welded 0# flanges. Tri-Lokt Hose Nipples Type 6 Stainless Steel The successful Tri-Lokt Nipple with the same exclusive features designed for higher pressure hose applications in stainless steel with stainless steel tie strips for superior corrosion resistance. Carbon Plated Steel, NPT, Swaged H Series Hose I.D. (In.) 4 H600 2 H H H60 4 H H60 4 H H68 Nipples complete with tie stripes. Type 6 Stainless Steel, NPT, Swaged S Series Size (in.) 4 S600 2 S S S60 4 S S60 Nipples complete with tie stripes. Brass NPT Ends BST Series 68 Size (in.) Brass NPT End 2 BST 4 BST 4 BST0 4 BST 2 BST BST2 2 2 BST0 4 BST 4 4 BST40 4 BST0 6 4 BST60 Replacement Tri-Lokt Yokes and Tie Strip Size (in.) SS Yokes 4 H006 8 H02 2 H022 4 H04 4 H040 Tri-Lokt is a registered trademark of Band-It -Idex Inc. Size (in.) SS Tie Strip Kits* 4 H604 2 H H H64 4 H H64 4 H H774 * set strips and jr. clamps.

69 HOSE COUPLINGS, FITTINGS, CLAMPS AND ACCESSORIES Shank Type Fittings continued King Combination Nipples continued Unplated Steel, Grooved End STV Series Jump Sizes, Plated Steel, Hose Shank x Male NPT STC Series Size (in.) Grooved End 4 STV0 4 STV 2 STV STV2 2 2 STV0 4 STV 4 4 STV40 4 STV0 6 4 STV STV STV STV20 Hose Male Shank NPT (In.) (In.) No. 4 x 4 STC00 4 x 4 STC00 4 x 4 STC0 4 x 4 STC0 4 x 2 STC20 2 x 4 STC20 2 x 2 4 STC x 2 STC x 2 2 STC x 2 4 STC x 4 STC0 4 x 2 2 STC0 4 x 4 4 STC x 4 STC40 King Steel Short Shank Suction Couplings (NPSM Thread) Female Steel with Brass Swivel Nut WF Series Size (in.) 4 WF2 2 WF0 2 4 WF WF20 4 WF WF WF600 King Steel Short Shank Suction continued Male Steel WM Series Size (in.) 4 WM2 2 WM0 2 2 WM WM20 2 WM WM WM600 Plated Steel Long Shank Couplings (NPSM Thread) Female with Swivel Nut SLS Series Male SLS Series Hose NPSM I.D. Thread (In.) (In.) 2 2 SLS SLS SLS848 Hose NPSM I.D. Thread (In.) (In.) 2 2 SLS SLS SLS88 Super King Long Shank Couplings for Bulk Handling Female with NPSM Thread Brass Nut Plated Steel Shank SD Series Male with NPT Thread RSK and SK Series Size (in.) 4 SD 2 SD SD2 2 2 SD0 4 SD 4 4 SD40 Size (in.) 6 Stainless Steel 2 4 RSK26 4 RSK6 Plated Steel 4 SK6 2 SK2 2 4 SK SK 4 SK6 4 4 SK46 69

70 HOSE COUPLINGS, FITTINGS, CLAMPS AND ACCESSORIES Shank Type Fittings continued Complete Foot Valve Assembly Painted DFV Series Strainer Standard Threaded, Round Hole Type Zinc Plated Steel RHS Series Size (in.) 2 DFVS DFVS DFVS00 2 DFVS0 4 2 DFVS DFVS DFVS DFVS DFVS20 Size (in.) 2 RHS20V 2 2 RHS RHS00 2 RHS0 4 2 RHS400 2 RHS RHS RHS RHS RHS20 Strainer Black Polyethylene Strainer TSS Series Size (in.) 2 TSS TSS2 2 TSS Skimmer Top Round Hole Type Zinc Plated Steel DST Series Size (in.) 2 DST DST2 2 DST Strainer Long Thin Round Hole Type Zinc Plated Steel RSS Series Size (in.) 2 RSS RSS2 2 2 RSS0 2 RSS 4 2 RSS40 70

71 HOSE COUPLINGS, FITTINGS, CLAMPS AND ACCESSORIES Food Grade Fittings The Sanitary End Stem, Bevel Seat Female End, Sanitary Clamps, Sanitary Gaskets and Ferrules are USDA approved and are designed to comply with the new -A standards for hose assemblies. Flow Chief Food Grade Fittings Sanitary End Stem IXSE Series Sanitary Clamp PFC Series Sanitary Gaskets PFG and PFG-TF Series Size (in.) 2 IXSE IXSE2 2 2 IXSE40 2 IXSE IXSE64 Size (in.) Size (in.) 2 PFC PFC2 2 2 PFC40 2 PFC PFC64 Buna-N* White 2 PFG PFG2 2 2 PFG40 2 PFG PFG64 Teflon White 2 PFG24TF 2 2 PFG2TF 2 2 PFG40TF 2 PFG48TF 4 2 PFG64TF *FDA approved. Bevel Seat Female IXFS Series Acme Thread Hex Nuts IXAN Series Size (in.) 2 IXFS IXFS2 2 2 IXFS40 2 IXFS IXFS64 Size (in.) 2 IXAN IXAN2 2 2 IXAN40 2 IXAN IXAN64 Bevel Seat Gaskets for Bevel Seat Fittings Buna N Black PFG-BS Series Male NPT Stem IXMS Series CB Fittings IXCBF, IXCBM and PFG-CB Series Size (in.) 2 PFG24BS 2 2 PFG2BS 2 2 PFG40BS 2 PFG48BS 4 2 PFG64BS Size (in.) 2 IXMS IXMS2 2 2 IXMS40 2 IXMS IXMS64 Size (in.) Female IXCBF48 Male IXCBM48 Gasket PFG48CB 7

72 HOSE COUPLINGS, FITTINGS, CLAMPS AND ACCESSORIES Nozzles and Hydrant Adapters Insulated Water Nozzles SN7 Pistol-Grip Water Nozzles CSN7 Heavy-duty brass valve and adjusting nut. Hold open clip locks any spray pattern. Chrome plated all zinc body. Industrial strength nylon handle. Rubber head guard on threaded GHT front version. Handle GHT threads. Hot water up to 80 F. Heavy-duty all zinc metallized body. Clip locks any spray pattern. Easy squeeze on/off lever. All brass valve stem and adjusting nut. Stainless steel spring with lifetime packing. Handle GHT threads. Thermo-Plastic Fire Hose Nozzle with Bumper FNB-GHT Series Size (in.) GHT Thread 4 FNB7GHT Brass Plain Hose Nozzles, Play Pipes Heavy-Duty Adjustable Hydrant Wrench HYD Wrench Brass Hydrant Adapters HYDRANT ADAPTER CHARTS CFDF = Cleveland Fire Department Female NST = National Standard Thread NPSHM = National Pipe Straight Hose Male NPT = National Pipe Tapered Reducer Pin Lug Adapter, Female x Male 69P Series Female x Male 2 2 CFDF x NPSHM 0-69P 2 2 NSTF x 2 NPSHM -69P 2 2 CFDF x 2 NSTM 20-69P 2 2 CFDF x 4 NPSHM 0-69P 2 2 CFDF x 2 NPSHM 40-69P 2 2 CFDF x 2 NPSHM 0-69P Double Male Adapter, Male x Male 8 Series Adapter, Female x Male 7 Series Male x Male 2 NPSHM x 2 NSTM NSTM x 2 2 NPSHM NPSHM x 2 NSTM CFDM x 2 2 NPSHM 0-8 Female x Male 2 NPTF x 2 NSTM NSTF x 2 2 NPTM -7 2 NSTF x 2 NPSHM NSTF x 2 2 NSTM NPSHF x 2 NSTM CFDF x 2 2 NPTM 40-7 Size Length (In.) (In.) No. GHT Thread, 00 psi 4 6 BN6F NPSH Thread 4 6 BN7F 4 8 BN0F 4 0 BN2F 2 0 BNF BN20F BN2F NST Thread 2 0 BNF BN2F Akron Fire Department (AFD) and Other Threads Available 72

73 HOSE COUPLINGS, FITTINGS, CLAMPS AND ACCESSORIES NPT Threaded Pipe Fittings Reducer Bushing 0 Malleable Iron Reducer Coupling 0 Malleable Iron Close Pipe Nipple Schedule 40 Welded Pipe Male NPT x Male NPT Carbon Steel Male x Female (In.) (In.) No. x 8 x 8 Bush x 2 x 2 Bush x 4 x 4 Bush 4 x 4x Bush 2 x 4 2x 4 Bush 2 x 2x Bush 2 x 4 2x 4 Bush 2 x 2x Bush 2 x 4 2x 4 Bush 2 x 2 2x 2 Bush x 2 x 2 Bush x 2 x2 Bush x 2 2 x2 2 Bush 4 x 2 4x2 Bush 4 x 2 2 4x2 2 Bush 4 x 4x Bush 6 x 4 6x4 Bush Other sizes available upon request. Female x Female (In.) (In.) No. 2 x 8 2x 8 Clpg 4 x 8 4x 8 Clpg 4 x 2 4x 2 Clpg x 8 x 8 Clpg x 2 x 2 Clpg x 4 x 4 Clpg 4 x 4 4x 4 Clpg 4 x 4x Clpg 2 x 4 2x 4 Clpg 2 x 2x Clpg 2 x 4 2x 4 Clpg 2 x 2x Clpg 2 x 4 2x 4 Clpg 2 x 2 2x 2 Clpg x 2 x2 Clpg 4 x 4x Clpg 6 x 4 6x4 Clpg Other sizes available upon request. NPT Size (In.) No. 4 Close Nip 8 Close Nip 2 Close Nip 4 Close Nip 4 Close Nip 4 4 Close Nip 2 2 Close Nip Close Nip 4 Close Nip Close Nip Other sizes available upon request. Brass Ball Valves For control of air, water, oil and gas in hose or pipe lines. Female NPT x Female NPT, Standard Port BBV Series Brass Fittings and Accessories Size (in.) Rated to 600 psi WOG and 0 psi steam 4 44BBV 8 46BBV 2 48BBV 4 2BBV 4 6BBV Rated to 400 psi WOG and 2 psi steam 4 20BBV 2 24BBV 2 4 2BBV Brass Short Shank Fittings Machined Female w/swivel Nut, GHT GHTF Series Machined Male, GHT GHTM Series Size (in.) 8 /8GHTF 2 /2GHTF 8 /8GHTF 4 /4GHTF Size (in.) 8 /8GHTM 2 /2GHTM 8 /8GHTM 4 /4GHTM 7

74 HOSE COUPLINGS, FITTINGS, CLAMPS AND ACCESSORIES Brass Fittings and Accessories continued Brass GHT Adapters (Washers not included) Female Swivel, GHT x GHT BA Series Female x Female GHT x GHT BA977 Brass Push-On Fittings Push-On NPT-Male Hose Barb National Pipe Tapered, Dryseal PMB Series Hose NPT Size (In.) (In.) PMB 4-244PMB PMB Female Swivel, GHT x Female NPT BAS Series Male GHT x Female NPT BA and FM Series Female x Female GHT x 2 NPT GHT x 4 NPT Male x Female GHT x 2 NPT GHT x 4 NPT GHT x NPT Rigid Female, GHT x Female NPT BA Series Female x Female GHT x 2 NPT GHT x 4 NPT BAS974 BAS976 BA794 BA796 FM076 BA974 BA PMB 4 4-4PMB PMB PMB 8-246PMB PMB PMB PMB 2-248PMB 4 8-2PMB 2 0-8PMB 2 2-8PMB 4-22PMB Push-On Female NPT Hose Barb National Pipe Tapered, Dryseal PFB Series Hose NPT Size (In.) (In.) 4 44PFB 8 46PFB 2 48PFB 4 2PFB Threaded Male, GHT x GHT BA Series Male x Male GHT x GHT BA777 Push-On Female JIC Swivel Hose Barb, Ball Seat National Pipe Straight PFJS Series Hose NPT Size (In.) (In.) PFJS 6 4-PFJS 8 4-6PFJS 6 6-2PFJS Threaded Male x Male NPT BA Series Male x Male GHT x 8 NPT GHT x 2 NPT GHT x 4 NPT BA76 BA746 BA PFJS 2 6-8PFJS 2-28PFJS 8 8-0PFJS 8-0PFJS 4-2PFJS Female GHT x Male NPT BMA and FM-T Series Female x Male GHT x 2 NPT GHT x 4 NPT GHT x NPT BMA974 BMA976 FM760T Push-On Hose Mender PMB Series Hose NPT Size (In.) (In.) LOM 6-24LOM 8-246LOM 2-248LOM 8 0-8LOM 4-22LOM 74

75 HOSE COUPLINGS, FITTINGS, CLAMPS AND ACCESSORIES Brass Fittings and Accessories continued Brass Barbed Hose Fittings Brass Female NPT Hose Inserts BI-F Series Hose NPT Size (In.) (In.) BI-2F 8 44BI-2F 4 44BI-4F 4 46BI-4F 8 46BI-6F Brass Hose Mender BSI Series Hose NPT Size (In.) (In.) BSI 44 44BSI 6 4BSI 84 46BSI 24 48BSI 84 0BSI 44 2BSI BI-8F Brass Male NPT Hose Inserts BI-M Series Hose NPT Size (In.) (In.) BI-2M 6 8 4BI-2M 4 4BI-4M BI-2M 4 44BI-4M 8 44BI-6M 6 8 4BI-2M 4 4BI-4M 8 4BI-6M BI-2M 4 46BI-4M 8 46BI-6M 2 46BI-8M BI-4M 8 48BI-6M 2 48BI-8M 4 48BI-2M 8 8 0BI-6M 2 0BI-8M 4 0BI-2M 4 2 2BI-8M 4 2BI-2M 4 6BI-2M 4 6BI-6M Brass Female NPT Swivel Fitting, Ball Seat BI-UFSB Series 4 Hose NPT Size (In.) (In.) 6 4 2BI-2F 8 4BI-2UFSB Tuff-Lite Nylon Inserts White TN Series Hose NPT Size (In.) (In.) 4 8 TN2 4 TN22 8 TN2 2 TN24 4 TN26 8 TN TN TN 4 TN2 8 TN 2 TN4 4 TN6 2 8 TN4 4 TN42 8 TN4 2 TN44 4 TN TN 2 TN4 4 TN6 4 8 TN6 2 TN64 4 TN66 8 TN68 4 TN86 8 TN TN8 4 TN0 2 TN TN20 2 TN TN BI-2UFSB 4 44BI-4UFSB 8 44BI-6UFSB 4 4BI-4UFSB 4 46BI-4UFSB 8 46BI-6UFSB 2 46BI-8UFSB 2 48BI-8UFSB 4 2BI-2UFSB 7

76 HOSE COUPLINGS, FITTINGS, CLAMPS AND ACCESSORIES Standard Brass Compression Fittings Used with: Copper, brass, aluminum and plastic tubing. Not recommended for steel tubing. Soft plastic tubing requires internal tube support. Advantages: Low cost. No flaring required. Easy to assemble. Available with long or short nut and in a wide range of styles and sizes. Typical applications: Gasoline, oil, water, vacuum lines, air lines, and other low and medium pressure uses where excessive vibration or tube movement is not involved. Use long nuts (6 Series) to improve vibration characteristics. Delrin Sleeve P60 Series Tube O.D. (In.) No. 4 P P60-8 P P P60-0 Use with Plastic Tubing. In-Line Sleeve M60 Series Long Nut 6 Series Tube O.D. (In.) No Brass Insert P6 Series Reducing Union 62R Series Tube O.D. (In.) x (In.) No. 4 x 8 62R-42 4 x 6 62R-4 6 x 4 62R-4 8 x 4 62R-64 8 x 6 62R-6 2 x 8 62R-86 8 x 8 62R-06 8 x 2 62R-08 Check Valve 6 Series Fitting Sleeve Nut Tubing Assembly instructions:. Slide nut and then sleeve on tubing. Threaded end of nut must face out. 2. Insert tubing into fitting body. Be sure tubing is bottomed on fitting shoulder.. Assemble nut to fitting body. 4. Tighten nut securely compressing sleeve to create seal with tube. Note: For soft plastic tubing insert proper tube support into plastic tubing and proceed as in Step. Delrin sleeve (P60 Series) can be used in place of brass sleeve to prevent cutting tube. Standard Sleeve 60 Series Tube O.D. (In.) No Tube O.D. (In.) Nut 6 Series Tube O.D. (In.) No. 8 M M60-4 M M M M60-0 Use with Plastic Tubing where alignment is necessary. No Tube O.D. NPT (In.) (In.) No P P P P P P P6-0 Union 62 Series Tube O.D. (In.) No Tube O.D. NPT (In.) (In.) No Tube O.D. (In.) Tee Three Tube Ends 64 Series No

77 Elbow Two Tube Ends 6 Series HOSE COUPLINGS, FITTINGS, CLAMPS AND ACCESSORIES Standard Brass Compression Fittings continued Male Connector 68 Series Male Elbow 69 Series Female Elbow 70 Series Tube O.D. (In.) Female Connector 66 Series Tube O.D. NPT (In.) (In.) No No Tube O.D. NPT (In.) (In.) No Tube O.D. NPT (In.) (In.) No Tube O.D. NPT (In.) (In.) No Tee Pipe on Branch 72 Series Slip Style Connector Tank Type 268 Series Tube O.D. NPT (In.) (In.) No Tee Pipe on Run 7 Series Tube O.D. NPT (In.) (In.) No v Tube O.D. NPT (In.) (In.) No

78 Bulkhead Union 7 Series HOSE COUPLINGS, FITTINGS, CLAMPS AND ACCESSORIES Standard Brass Compression Fittings continued Tee Pipe on Run 76 Series 4 Male Elbow 77 Series Tube O.D. (In.) No N 8 7-6N 2 7-8N 4 *7-4N* *Locknut Only Tube O.D. NPT (In.) (In.) No Tube O.D. NPT (In.) (In.) No Used with: Brass, copper and iron pipe. Advantages: Positive mechanical seal. Large range of styles and sizes available. Typical applications: Could be used with water, air, oil, natural gas and liquefied petroleum products. Actual Size of Pipe Thread at Small End 8 4 Brass Pipe Fittings Reducing Coupling 0 Series Pipe Thread (In.) x (In.) No. 4 x x x x x x x x x x x x Tee 0 Series Pipe Thrd. (In.) No Cross 02 Series Coupling 0 Series Pipe Thrd. (In.) No Union 04 Series Elbow 00 Series Pipe Thrd. (In.) No. Pipe Thrd. (In.) No Pipe Thrd. (In.) No

79 HOSE COUPLINGS, FITTINGS, CLAMPS AND ACCESSORIES Brass Pipe Fittings continued Cap 08 Series Long Nipple Series Close Nipple 2 Series Plug Recessed Hex Head 8 Series Pipe Thrd. (In.) Square Head Plug 09 Series Pipe Thrd. (In.) No Bushing 0 Series Pipe Thread (In.) x (In.) No. 4 x x x x x x x x x x x x x x Lock Nut Series Pipe Thrd. (In.) No No Pipe Thrd. Lgth. (In.) x (In.) No. 8 x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x Pipe Thrd. (In.) No Pipe Flange 4 Series Pipe Thrd. (In.) Street Elbow 6 Series Pipe Thrd. (In.) No F x 8M Plug Slotted Head 7 Series Pipe Thrd. (In.) No No Pipe Thrd. (In.) No Adapter 20 Series Pipe Thrd. (In.) No v Plug Hex Head 2 Series Pipe Thrd. (In.) No Reducing Adapter 20R Series Pipe Thread (In.) x (In.) No. 4 x 8 20R x 8 20R x 4 20R x 8 20R x 2 20R-282 x 4 20R-62 79

80 HOSE COUPLINGS, FITTINGS, CLAMPS AND ACCESSORIES Brass Pipe Fittings continued Hex Nipple 22 Series 4 Street Elbow 24 Series Service Tee Male Pipe on Run 27 Series 4 Elbow 29 Series Pipe Thrd. (In.) No Reducing Hex Nipple 2 Series Pipe Thrd. (In.) No Male Elbow 26 Series Pipe Thrd. (In.) No. 8F x M x F F x M x F F x M x F F x M x F 27-8 Service Tee Male Pipe on Branch 28 Series Pipe Thrd. (In.) No Fuseable Pipe Plug 2 Series Pipe Thrd. Melting (In.) Point No. Pipe Thread (In.) x (In.) No. 4 x x x x x x Pipe Thrd. (In.) No x x x Pipe Thrd. (In.) No. 8F x F x M F x F x M F x F x M F x F x M

81 HOSE COUPLINGS, FITTINGS, CLAMPS AND ACCESSORIES Clamps Standard Duty Worm Gear Clamp Miniature Worm Gear Clamp Heavy-Duty, High Torque Screw: 6 hex-head stainless steel. Band and housing: 2 wide stainless steel. Clamp Diameters English (In.) Min. Max. No v Screw: 4 hex-head. Band and housing: 6 wide. 62M Series has 00 series marine grade stainless steel screw, band and housing. Clamp Diameters English (In.) Min. Max. No M M M M M M M M M M6 The premier clamp in the industry. Screw: 6 hex-head. 40 grade stainless steel. Band: 8 wide;.027 thick. 04 grade stainless steel. Housing and saddle: 8 wide;.060 thick. 04 grade stainless steel. Clamp Diameters English (In.) Min. Max. No

82 HOSE COUPLINGS, FITTINGS, CLAMPS AND ACCESSORIES Clamps continued Make-A-Clamp Style TBC Stainless Steel Band, Carbon Steel Bolt Center Punch Clamps This is a maintenance clamp system in a box. By simply cutting off a piece of banding from a continuous roll, you can make any size 0 stainless steel worm-driven clamp from 2 diameter and up. It s a must for anyone likely to encounter requirements for varying sized large clamps. 2 band width,.02 thickness. Reusable. Contents 82 No. Retail kit 8 2 band, adj. fasteners, band splice 4000 Kit with 00 band, 2 adj. fasteners, 0 band splices 400 Kit with 0 band, 0 adj. fasteners, band splices 4002 Adj. fastener Shipped 0 fasteners per box 4004 Box with 00 band,0 band splices 400 Box with 0 band, band splices demonstrator kit with clamps 4007 Bridge Clamps 2 24 I.D. Bridge clamps are preformed to bridge helical wire, providing a secure fit without leakage for non-cuffed hoses. Secure fit on duct and vent hoses without leakage. Style TBC 4 wide 00 series stainless steel band,.02 thick. Opens 6 above and tightens 8 smaller than nominal I.D. for a total of 6 range for clamps TBC0 through TBC20. Opens 6 above and tightens 7 2 smaller than nominal I.D. for clamps TBC26 through TBC70 for a total of 9 2 range. Carbon steel bolt. Torque rating 70 in/lb. O.D. Range (In.) Min. Max. No. 2 2 *TBC* TBC0 8 6 TBC7 4 6 TBC TBC TBC TBC TBC TBC TBC TBC TBC TBC TBC2 2 6 TBC TBC TBC TBC TBC TBC TBC TBC TBC TBC TBC TBC TBC TBC TBC TBC TBC70 *With Saddle Quick Release Latch. BAND-IT CP series center punch clamps are available in 20 stainless steel or heat treated galvanized carbon steel. CP clamps are locked with a standard conical punch, ensuring a strong, powerful lock for reliable clamping. Both 20 stainless steel and galvanized carbon steel center punch clamps are manufactured with 20 stainless steel buckles to provide maximum locking strength. CP clamps should be installed with BAND-IT s T00, T0 or S8 center punch tools. Type 20 Galvanized Clamp Band SS Carbon Stl. I.D. Width (In.) (In.) No. No. 8 wide clamp.02 thick. 8 wide clamp.02 thick CPS CP 8 CPS CP 8 CP4S CP4 8 CPS CP 8 CP6S CP6 8 CP7S CP7 8 CP8S CP8 8 CP9S CP9 8 CP0S CP0 8 CPS CP 8 CP2S CP2 8 CP4S CP4 8 CP6S CP6 8 CP8S CP8 8 CP20S CP20 8 CP24S CP24 8 CP28S CP28 8 CP2S CP2 Band-It is a registered trademark of Band-It -Idex Inc.

83 HOSE COUPLINGS, FITTINGS, CLAMPS AND ACCESSORIES Clamps continued Standard Duty BAND-IT Clamp The BAND-IT Tool C00 Giant Tool G402 BAND-IT Band in Type 20 stainless steel has been the industry standard for nearly 60 years with its superior yield and tensile strength properties for maximum clamping strength. And product innovations such as BAND-IT Totes and patented EASY SCALE make the BAND-IT Band Clamping System better than ever. All BAND-IT sizes feature fully rounded smooth edges for safety and easy installation. For clamps of even greater strength, use a double wrap, threading the Ear-Lokt Buckle each time around. Width Thickness (In.) (In.) No. Type 20 Stainless Steel, 00 per roll 6.0 C C C C C C206 BAND-IT Buckles Ear-Lokt Buckles in Type 20 stainless steel are designed to accommodate both single and double wrap clamps. The unique teeth and ears provide for maximum clamping strength. Width (In.) No. Type 20 Stainless Steel 6 C2 4 C22 8 C2 2 C24 8 C2 4 C26 Package quantity: 00 Giant Band Giant Band is available in Type 20 stainless steel. It is used for heavyduty clamping applications. Giant 4 band in 20 stainless steel has a breaking strength of,00 pounds. Double wrapped clamps are recommended for maximum strength. Width Thickness (In.) (In.) No. Type 20 Stainless Steel, 00 per roll G G G42 Giant Buckles Giant Buckles, Ear-Lokt, are offered in widths to correspond to Giant Band. Giant clamps may be double wrapped for extra strength. Width (In.) No. Type 20/0 Stainless Steel 4 G440 4 G44 4 G442 Package quantity: 2 The Giant Tool must be used to apply heavy-duty Giant clamps. Measuring 6 2 in length, it is designed to pull up to 6,000 pounds. Center Punch Open-End Clamps Austenitic stainless steel open-end clamps are tensioned, then locked by striking tool punch with mallet or hammer. Use BAND-IT Center Punch tools. Max Dia. Max Dia. Band Once Twice Total Width Around Around Length (In.) (In.) (In.) (In.) No. Type Stainless Steel OS O0S O6S O20S Other sizes available. Band-It is a registered trademark of Band-It -Idex Inc. 8

84 HOSE COUPLINGS, FITTINGS, CLAMPS AND ACCESSORIES Clamps continued Center Punch Tools Double Ear Clamps Zinc Plated Steel Band Spiral Clamps Clockwise Wound T00 Description S8 These ratchet action tensioning tools are for applying Center Punch and Center Punch Open-End clamps with a center punch lock. No. For 8 Wide Clamps T00 For 8 Wide Clamps T0 8 Adapter Insert for T00 Tool S02 Mallet (Forged Steel) T26 For 8 and 8 Wide Clamps S08 Replacement s Center Punch Head for T00 and T0 Center Punch Holder for T00 and T0 Punch for T00 and T0 Replacement Punch Assembly for S8 Winding Mandrel Assembly Other sizes available. T2 T22 S90 S202 J08 When ordering Double Ear Clamps, select nominal clamp size nearest to, but always larger than, O.D. of material to be clamped after insert has been fitted. Nominal Closed Open Size (In.) (In.) No For use on convoluted cover hose. Clamps are Plated Steel. Hose I.D. (In.) No. Type 20/0 Stainless Steel Power Clamp Power Clamp 2 2 Power Clamp Power Clamp 2 Power Clamp 6 26 Power Clamp Power Clamp 0 Power Clamp Oetiker Clamp Tool for Pinch-On Clamps

85 HOSE COUPLINGS, FITTINGS, CLAMPS AND ACCESSORIES Clamps continued Double Bolt Clamps With Two Saddles Hose Support Clamps A rugged, plated malleable iron twobolt clamp with machine bolts and hex nuts. Inner surface has dual gripping ridges. Bolt lugs are reinforced to prevent bending out of alignment. O.D. Range (In.) Min. Max. Torque* No *Recommended Torque rated in ft/lbs. Prevents damage to hose. Provides hose support where long lengths are used. Minimizes hose chafing problems. Avoids twisting of hose lines, especially when hose is routed in two directions. Provides neater installation of hose lines. Hose I.D. (In.) No CL-6 2 CL CL CL- 6 CL CL- 6 CL CL CL-9 66 CL CL CL CL- 466 CL CL CL-4 8

86 HOSE COUPLINGS, FITTINGS, CLAMPS AND ACCESSORIES Nozzles OPW 90 Manual Nozzles For High Flow, Bulk Fuel Oil Delivery Service OPW 7H Automatic Shut-Off Nozzles For Heavy-Duty, High Flow Truck, Bus and Fleet Service Spout Optional Aluminum body lighterweight, easier to maneuver. Dual poppets easy to open nozzle against high inlet pressures. Four position hold-open feature for use when fueling large capacity tanks. Nozzle must be attended at all times during usage. Right angle design provides larger lever area for better grip and easier control; permits nozzle to fit into awkward spaces close to walls and into corners. Drag lugs protect the nozzle when dragged across rough surfaces; adds to long life with rough usage. Easily replaced spout the spout is simply threaded into the body. Replacement spouts are readily available from Summers Rubber Company. NPT female threads at inlet end standard pipe threads accept all standard, 4, 2 and 2 male connections. Materials: Body: Cast aluminum. Main stem: Stainless steel. Stem seal: Graphite with Teflon. Disc: Viton. Spout: OPW 296 brass or 297 aluminum (optional). Size Government (In.) No. Description National Stock No A-44 with Flexible Brass Spout G-B04 with Spout and Ground Wire GW- for Potable Water with Spout If you operate a full service truckstop, refuel your own fleet, or manage a cardlock refueling location, the low cost, long life and durability of the OPW 7H high flow nozzle can help increase your productivity, sales and profits. Even, smooth spray pattern minimizes diesel foaming and false shutoffs. Extra long anchor spring keeps the OPW 7H secure in most large fill openings. Helps reduce spills a unique two-stage lever design assures a positive shut-off, even if held wide open. Three position hold-open device one finger control of hold-open mechanism means easy setting of flow rate. Easily replaced spout simply remove three screws. Replacement kits are readily available from Summers Rubber Company. Dash-pot action for smoother closing action and reduced line shock. Dual poppets easy to open nozzle against high pressure. Available with FlowLock designed to shut-off automatically when the spout is tipped up, limiting spillage. Listed by Underwriters Laboratories Inc. BSPP threads available by ordering the OPW 7HL. Materials: Body: Aluminum. Lever and lever guard: Durotuff. Packing: Graphite with Teflon. Disc: Viton. Inlet size: NPT. WARNING: Do not use OPW 7H Nozzles with a hold-open device on pre-pay self-service installations. Use of foreign objects to hold open automatic nozzles could result in failure to shut-off and personal injury. Hand Insulator 7H with Color 7H FlowLock Green 7H-000 7H-00 Black 7H H-040 Yellow 7H H-090 Teflon and Viton are registered trademarks of the Dupont Co. 7H is a registered trademark and FlowLock is a trademark of OPW Fueling Components. Durotuff is a registered trademark of OPW. 86

87 HOSE COUPLINGS, FITTINGS, CLAMPS AND ACCESSORIES Hose Reels Hose Reels in All Sizes and Capacities Hannay Reels is the leading manufacturer of high quality hose and cable reels for most every conceivable application. This catalog describes and gives specifications on the most popular hose reels. If you don t find what you re looking for, call Summers Rubber Company and we will help you meet your needs. Reel Selector Chart Hose I.D. Sizes (In.) Reel Type 4 2 Hose Assemblies Spring Rewind Reels 4 2 Series LN 4 8 Series N00 (high pressure) 4 4 Dual Series N600/600 (dual hose) 8 & 2 Series N700/700 4 & Series N800/800 4 & 2 Series 900 Compact Manual Rewind Reels 4 8 Series 000 Power Rewind Reels 4 Series 00, 800, Dual Series 2000, 7000 (dual hose) 2 Series Series Series Series 9000 Manual Rewind Reels 4 2 Series 000, 00 Storage Reels 4 2 Series C200, C00 Spring Rewind Reels Manual Rewind Reels Compact Manual Rewind Reels Power Rewind Reels Storage Reels Portable Storage Reels Model C6-0- The model C6-0- portable cable storage reel is small, lightweight, and durable for quick and easy use especially in fire/rescue, mobile broadcasting, or industrial maintenance and repair applications where long lengths of cable are payed out over large areas. This model is supplied with a spring drag device to brake the reel. Model C Model C is a strong, portable reel for storing higher capacities. Steel construction with direct crank rewind for fast, easy pickup. Model C is supplied with a spring drag device used to brake the reel. An optional pin lock (PL-2) is available at additional cost. Rewind Models C6-0- and C feature crank rewind handles permanently attached to the disc. Insert cable in opening in drum and disc to initiate winding. Note: These storage reels have no live connections. Portable Storage Reels For Broadcast Cable Extension Cord Forestry Fire Hose Rope Model C For Broadcast Cable Extension Cord Rope Model C

88 HOSE COUPLINGS, FITTINGS, CLAMPS AND ACCESSORIES Hose Reels continued Portable Garden Hose Reels To Handle 2 through I.D. Hose GH00 For Grounds Maintenance Restaurants Home Use GHAT200 Hannay Hose Reel Models GH00 and GHAT200 are designed for portable use in grounds maintenance by the restaurant, fast food, hotel and other industries. Hannay portable reels get to and from the job fast. Pickup and storage are quick and neat, keeping hose safely out of the way while minimizing wear and tear. Models GH00 and GHAT200 are continuous flow reels with swivel joint inlet, fluid hub and outlet riser. Model GHAT200 comes with pneumatic tires. Rewind Direct crank rewind. Model GH00 has a permanently attached crank. Model GHAT200 has a removable crank. Inlet Model GH00 standard inlet is 90 ball bearing swivel joint with 2 female NPT threads. Model GHAT200 standard inlet is 90 ball bearing swivel joint with female NPT threads. Outlet Model GH00 and GHAT200 standard outlet is male GHT threads. Other sizes and/or threads, including female NPT threads, can be furnished and must be specified. When specifying other than GHT threads delete prefix GH from model number. Operating Pressures and Temperatures Model GH00 operates at pressures to 000 psi and temperatures from 20 F to 400 F (-7 C to 204 C). Model GHAT200 operates at pressures to 000 psi and temperatures from 20 F to 400 F (-7 C to 204 C). Reels to operate at other pressures and temperatures can be furnished at extra cost. Stainless Steel Manual Rewind Reels 88 Portable Storage Reels Series SS00 to Handle Single 4 through 8 I.D. Hose Series SS800 to Handle Single 2 through 4 I.D. Hose Series SS4000 to Handle Single 2 through I.D. Hose Hannay s strong, lightweight compact reels designed for long lengths of hose. These compact reels are exceptionally versatile and able to meet your special requirements. Rewind Manual A direct crank rewind is permanently attached to the reel axle on Series SS00, SS800, and SS4000. Brakes and Locks Reels with direct crank rewind are supplied with an adjustable spring tension brake and spring actuated pin lock as standard. Inlet Series SS00 standard inlet is 90 ball bearing swivel joint with 2 female NPT threads. Series SS800 and SS4000 standard inlet is 90 ball bearing swivel joint with female NPT threads. Outlet Series SS00 standard outlet is 2 female NPT threads. Series SS800 standard outlet is 4 female NPT threads. Series SS4000 standard outlet is female NPT threads. Other sizes and/or threads can be furnished, must be specified. Optional Rollers Rollers may be purchased as accessory items. Specify roller position when ordering. Mounting brackets are necessary. Operating Pressures and Temperatures Series SS00 these reels operate at pressures to 000 psi and handle product temperatures from 20 F to 400 F (-7 C to 204 C). Series SS800 and SS4000 these reels operate at pressures to 000 psi and handle product temperatures from 20 F to 400 F (-7 C to 204 C). Reels to operate at other pressures and temperatures can be furnished at extra cost.

89 HOSE COUPLINGS, FITTINGS, CLAMPS AND ACCESSORIES Hose Reels continued Stainless Steel Spring Rewind Reels To Handle Single 4 through 2 I.D. Hose Series SSLN700 Series SSN700 Series SSN700 and SSLN700 reels offer a narrow frame for compact mounting. The SSLN700 reels are designed for in-plant and processing applications and not for vehicle or mill duty use. Rewind A heavy-duty spring motor provides self-contained rewind power. A non sparking ratchet assembly locks the reel when the desired length of hose has been payed out. A pull on the hose unlocks the reel and the spring motor retracts the hose. A declutching arbor is provided to prevent damage from reverse winding. Inlet/Outlet Standard inlet is 90 ball bearing swivel joint with 2 female NPT threads. Standard outlet is 2 female NPT threads. Other sizes and/or threads can be furnished and must be specified. Operating Pressures and Temperatures These reels operate at pressures to 000 psi and handle product temperatures from 20 F to 400 F (-7 C to 204 C). Reels to operate at other pressures and temperatures can be furnished at extra cost. Rollers All models are supplied with a 4-way roller assembly. Roller position must be specified. Hose Stop A hose stop should be used to prevent damage to rollers and nozzles and to permit adjustment of free hose length. To receive a detailed parts breakdown drawing for Series SSLN700, request ISO 72; for Series SSN700, request ISO 7. Pressure Gauges, Steel Case Dry 2 Dry, 4 Bottom Stem 2 2 Dry, 4 Bottom Stem Graduation psi No. Major Minor Range DRY DRY DRY DRY DRY DRY DRY 2 Graduation psi No. Major Minor Range , DRY , DRY , DRY , DRY , DRY , DRY , DRY , DRY , DRY , DRY , DRY , DRY

90 HOSE COUPLINGS, FITTINGS, CLAMPS AND ACCESSORIES Pressure Gauges, Steel Case Dry continued 2 Dry, 4 Center Back Mount Graduation psi No. Major Minor Range DRY CBM DRY CBM DRY CBM DRY CBM DRY CBM 2 Pressure Gauges, Stainless Case Liquid Filled 2 2 Stainless Steel, Liquid Filled, Brass Internals, 4 Bottom Stem 2 2 Stainless Steel, Liquid Filled, Brass Internals, 4 Center Back Mount Graduation psi No. Major Minor Range 0 Hg 000-psi 000VAC-0 Liquid Fld 0 Hg 00-psi 00VAC-0 Liquid Fld 0 Hg 060-psi 00VAC-60 Liquid Fld 0 Hg 60-psi 0VAC-60 Liquid Fld , Liquid Fld , Liquid Fld , Liquid Fld , Liquid Fld , Liquid Fld , Liquid Fld , Liquid Fld , Liquid Fld , Liquid Fld , Liquid Fld , Liquid Fld , Liquid Fld , Liquid Fld , Liquid Fld , Liquid Fld , Liquid Fld , Liquid Fld Graduation psi No. Major Minor Range , CBM Liq Fld , CBM Liq Fld , CBM Liq Fld , CBM Liq Fld , CBM Liq Fld , CBM Liq Fld , CBM Liq Fld , CBM Liq Fld , CBM Liq Fld , CBM Liq Fld , CBM Liq Fld , CBM Liq Fld , CBM Liq Fld , CBM Liq Fld 90

91 Annular Corrugated Stainless Steel Hose SPECIAL APPLICATION HOSES, METAL & TEFLON HOSES Corrugated Metal Hose Max. Static Dynamic No. Working Min. Bend Min. Bend I.D. of Pressure Radius Radius (In.) Braids (psi) (In.) (In.) Annular hose is available in T2 and T6L stainless steel. Metal hose is used when temperature extremes, corrosive media, or permeation preclude the use of rubber, PTFE, or plastic hose. Typical applications are found in steel making, chemical processing, paper manufacturing, petroleum refining, and in numerous other industrial applications. Explanation of Numbers: Available T2 Stainless Steel T6L Stainless Steel Braid Types Unbraided T04 Single Braided T04 Double Braided , SS Metal Hose,77 2 2, , SS Metal Hose,420 2, , SS Metal Hose,8 2 2, , SS Metal Hose,86 2, , SS Metal Hose,20 2, , SS Metal Hose,898 2, , SS Metal Hose,78 2, , SS Metal Hose,64 2, , SS Metal Hose, 2, , SS Metal Hose,449 2, , SS Metal Hose,47 2, , SS Metal Hose,46 2, , SS Metal Hose,299 2, , SS Metal Hose,27 2, , SS Metal Hose,20 2, 9

92 SPECIAL APPLICATION HOSES, METAL & TEFLON HOSES Chemical Transfer Hose ChemKing Chemical Transfer Hose Static Dynamic Inside Outside Number Min. Bend Min. Bend Working Dia. Dia. of Radius Radius Pressure (In.) (In.) Braids (In.) (In.) psi , , , , , ,674 Note: Braid is T6 stainless steel. Monel braid is offered upon request. When Monel braid is used, stated pressure ratings need to be reduced by a factor of 0.7. numbers for Monel Braid are AL 6780 (Single Braid), and AL 6788 (Double Braid). ChemKing is the ultimate metal hose for chemical transfer. Made from C-276 alloy, ChemKing offers unparalleled corrosion resistance. C-276 is one of the most universally corrosion resistant materials available and is used in a range of environments from moderately oxidizing to strongly reducing. ChemKing provides excellent corrosion resistance to many of the most severe applications found in chemical processing. In fact, there is such a high level of pitting corrosion resistance that it is considered inert to seawater and is used in many seawater, brine, and high chloride environments, even at strong acid ph values. 2 In addition, ChemKing may be used for hydrogen sulfide found in sour gas wells. ChemKing is also extremely flexible. Hose Master s unique hydroforming technology minimizes stress during the corrugating process, resulting in a longer lasting, more flexible chemical or gas transfer hose. Nos.: AL 6700 (No Braid) Nos.: AL 6740 (Single Braid) Nos.: AL 6744 (Double Braid) Technical Data Blue Sheet, Nickel-Base Alloy Allegheny Ludlum AL-276 (UNS Designation N0276), Allegheny Ludlum, B-70-ED 989, p.2 2 Id, p. ChlorSafe Chlorine Transfer Hose Nos.: AL 6740 (Single Braid) Nos.: AL 6744 (Double Braid) Min. Inside Outside Number Dynamic Max. Min. Dia. Dia. of Bend Radius Working Burst (In.) (In.) *Braids* (In.) Pressure **Pressure** , , ,87 **Standard Braid is T6 stainless steel. Monel braid is offered upon request (double braid is required for all sizes using Monel braid. Number for Monel Braid is AL 6788). **Chlorine Institute specification pressure ratings represent a to safety factor. ChemKing and ChlorSafe are registered trademarks of Hose Master Inc. Chlorine Transfer Hose ChlorSafe is the answer to chlorine transfer problems. Made from C-276 alloy, ChlorSafe can stand up where other alloys fail. No matter how hard you try, it is nearly impossible to keep chlorine dry. When moisture combines with the chlorine, hydrochloric acid is created. This noxious chemical destroys traditional metal hose. But C-276 is one of the few materials available that resists hydrochloric acid s corrosive properties. Seam weld integrity is a concern for anyone using chlorine transfer hose. Another unique advantage of C-276 is its resistance to carbide precipitation during welding, maintaining corrosion resistance even in the heat-affected zones of welded joints. This, coupled with Hose Master s proprietary seam weld technology, ensures that ChlorSafe is truly worry-free. This unique hydroforming technique minimizes stress during the corrugating process, resulting in a longer lasting, more flexible metal hose. Couple this with the extreme corrosion resistance of C-276 alloy, and see why ChlorSafe is the best chlorine transfer hose. Assemblies are available with C-276 male nipples or C-276 A stub ends with 00 lb. ANSI carbon steel flanges. All assemblies are fabricated in accordance to the Chlorine Institute guidelines.

93 SPECIAL APPLICATION HOSES, METAL & TEFLON HOSES Fabricated Corrugated Assemblies Fitting Explanation Alloy Male Pipe Nipple Sch. 40 TOE (Thread One End) pipe nipple with NPT threads. SS, CS, Brass Other threads and schedules available. Hex Male Fitting NPT thread fitting complete with an integral wrench flat hex. SS, CS, Brass Solid Female Pipe 0# female fitting with NPT internal thread. SS, CS, Bronze Heavier ratings available. Female Union Ground joint 0# female union with NPT thread. SS, MI, FS, Brass Higher pressure ratings and washer joint unions are available. Weld Nipple Sch. 40 pipe beveled for butt welding. SS, CS Sch. 80 and 60 also available. Tube Ends Wide range of wall gauges and bent tube ends available. SS, CS, Copper JIC Female Swivel Also available in SAE configuration for cryogenic SS, CS, Brass and automotive applications. Victaulic Male Nipple Sch. 40 pipe grooved for victaulic clamping. SS, CS Sch. 80 and 60 also available. Sanitary (vacuum) Fittings Available in standard and special configurations. SS Weld Neck Flange Raised face, ASTM 0# rated. SS, FS Other ratings and facings available. A Stub & Lap Joint Flange Sch. 40 type A stub end with ASTM 0# lap joint flange. SS, CS Other flange ratings available. C Stub & Slip-On Flange Sch. 0 type C stub end with ASTM 0# slip-on flange. SS, FS Other schedules and flange ratings available. Slip-On Flange ASTM 0# rated raised face slip-on flange. SS, FS Other ratings and facings available. Plate Flange 0# drilling. Variety of thicknesses and drillings SS, CS available including TTMA specifications. Weld Reducer Available in a wide range of reductions and schedules. SS, CS 9

94 SPECIAL APPLICATION HOSES, METAL & TEFLON HOSES Special Fabricated Assemblies Jacketed Assembly Lined Assembly Jacketed assemblies are normally used in one of the following applications:. As a heated transfer line for those products, such as sulphur, which must be maintained at an elevated temperature in order to flow readily. Steam or hot oil is circulated through the jacket, which in turn heats the product being conveyed in the core hose. 2. As a cryogenic transfer line. Maintaining a high vacuum in the jacket effectively insulates cryogenic liquids being conveyed in the core hose. Product being conveyed through an unlined corrugated metal hose at high velocity can set up resonant vibration within the hose causing it to prematurely fail. This may be eliminated by adding a liner to the hose. Traced Assembly Guarded Assembly Traced hose assemblies are used when the product being conveyed must be heated in order to flow freely. Steam or hot oil circulated through the inner tracer hose heats the product in order to maintain high flow rates. Guarded assemblies are used where a corrugated metal hose could easily be damaged by rough handling, abrasion, or flexing past its minimum bend radius. 94

95 SPECIAL APPLICATION HOSES, METAL & TEFLON HOSES Interlocked Metal Hose Interflex INTERFLEX is a quality, general purpose interlocked metal hose formed from a single metal strip. Pressure and vacuum capabilities may be easily enhanced by the selection of an appropriate packing material. Interflex is available in various alloys, metal strip thicknesses and in diameters from 2 through 6. Interlocked hose is available in any length up to 00 and can be provided in bulk or fabricated assemblies. A sampling of some industries and their applications for Interflex hose are: Agriculture, lumber, chemical, petroleum refining, municipalities, tank truck. Packings Available for Increased Pressure and Vacuum Capabilities Packing Max. Type Features Temp. Cotton Most economical packing 80 F Elastomeric Provides maximum pressure and vacuum capability 200 F Copper For high temperatures 800 F High Temp. Fiber Specially coated high temperature filament 000 F Stainless Steel For extreme temperatures 200 F Explanation of Interflex Numbers: Strip Thicknesses Material Codes 0 Extra Lightweight AL Aluminum Lightweight GS Galvanized Steel 8 Medium Weight SS T04 Stainless Steel 20 Light Heavyweight 6 T6 Stainless Steel 2 Heavyweight 0 Extra Heavyweight IN 0 IN IN 8 IN 2 IN 0 IN 20 GS, SS GS, SS GS, SS, 6 GS, SS GS AL Min. Min. Min. Min. Min. Min. Wt. Bend Wt. Bend Wt. Bend Wt. Bend Wt. Bend Wt. Bend I.D. /ft. Radius /ft. Radius /ft. Radius /ft. Radius /ft. Radius /ft. Radius (In.) (Lbs.) (In.) (Lbs.) (In.) (Lbs.) (In.) (Lbs.) (In.) (Lbs.) (In.) (Lbs.) (In.) Notes: Other diameters are available on request. For packed hose add 0% to both weight per foot and minimum bend radius. Minimum bend radius is Notes: measured from the center line of the hose. Technical data is meant to be used as a guide. If more specific information is required, please contact Summers Rubber Company. 9

96 SPECIAL APPLICATION HOSES, METAL & TEFLON HOSES Interlocked Metal Hose continued Ultraflex ULTRAFLEX is a smoothbore hose ideally suited for dry bulk pneumatic conveying. This hose is produced with a durable armor and a highly abrasionresistant liner. Ultraflex is available in various alloys, metal strip thicknesses and in diameters from 2 through 6. Smoothbore hose is available in any length up to 00 and can be provided in bulk or fabricated assemblies. A sampling of some industries and their applications for Ultraflex hose are: Brewing, cement, food processing, mining, plastic pellets. Packings Available for Increased Pressure and Vacuum Capabilities Packing Max. Type Features Temp. Cotton Most economical packing 80 F Elastomeric Provides maximum pressure and vacuum capability 200 F Copper For high temperatures 800 F High Temp. Fiber Specially coated high temperature filament 000 F Stainless Steel For extreme temperatures 200 F Explanation of Ultraflex Numbers Armor Materials Armor Strip A Aluminum Lightweight G Galvanized Steel 8 Medium Weight S T04 Stainless Steel 20 Light Heavyweight 6 T6 Stainless Steel 2 Heavyweight Liner Material S T0 Stainless Steel 4 T40 Stainless Steel C Carbon Steel UF UF 8 UF 2 UF A 20 G, S / C, S, 4 G, S, 6 / C, S, 4 G, S / C, S A / C, S Min. Min. Min. Min. Wt. Bend Wt. Bend Wt. Bend Wt. Bend I.D. /ft. Radius /ft. Radius /ft. Radius /ft. Radius (In.) (Lbs.) (In.) (Lbs.) (In.) (Lbs.) (In.) (Lbs.) (In.) Notes: Other diameters are available on request. For packed hose add 0% to both weight per foot and Notes: minimum bend radius. Minimum bend radius is measured from the center line of the hose. Technical data is meant to be used as a guide. If more specific information is required, please contact Summers Rubber Company. 96

97 SPECIAL APPLICATION HOSES, METAL & TEFLON HOSES Interlocked Metal Hose continued Guard and B.O.P. Guard and BOP are both loose-wound interlocked metal hose formed from a single strip of steel. These products are specifically designed and engineered to be used as rugged protective armor over rubber, plastic, metal, and PTFE hose assemblies. These hoses are manufactured from various metals and strip thicknesses, and are available in diameters from 2 through 6 and in any length. A sampling of some industries and their applications for Guard and B.O.P. hose are: Marine, oil exploration, steel making, construction, electric cable conduit. Tar and Asphalt Tar and Asphalt hose is a sturdy and flexible interlocked metal hose specifically designed for the transfer of high temperature viscous fluids. Mechanically attached fittings allow for easy installation at the factory or in the field. Tar and Asphalt hose is available in standard lengths of 60 or 00 but can be provided in a any specified length up to 00. A sampling of some industries which commonly use Tar and Asphalt hose are: Refineries, municipalities, contractors, highway commissions. Refer to page 9 for Rubber Tar and Asphalt Hose. Interlocked Fabricated Assemblies Refer to end fitting styles on the next page. 97

98 SPECIAL APPLICATION HOSES, METAL & TEFLON HOSES Fabricated Interlock Assemblies Fitting Explanation Alloy Male Pipe Nipple Sch. 40 T.O.E. (Thread One End) pipe nipple with NPT threads. SS, AL, CS, Brass Other threads and schedules available. Victaulic Male Nipple Sch. 40 pipe grooved for victaulic clamping. SS, C Sch. 80 and 60 also available. Tube Ends Wide range of wall gauges and bent tube ends available. SS, AL, CS Plate Flange 0# drilling. Variety of thicknesses and drillings SS, CS available including TTMA specifications. Slip-On Flange ASTM 0# rated raised face slip-on flange. SS, FS Other ratings and facings available. C Stub and Slip-On Sch. 0 Type C stub end with ASTM 0# slip-on flange. SS, FS Other schedules and flange ratings available. A Cam and Available from 2 to 2 size. SS, AL, CS, Bronze Groove Adapter D Cam and Available from 2 to 2 size. SS, AL, CS, Bronze Groove Adapter Compensator Provides a convenient method of attaching a shank type Urethane fitting to interlocked hose. Also helps relieve stress in the fitting to hose connection. 98

99 SPECIAL APPLICATION HOSES, METAL & TEFLON HOSES Teflon Hose Assemblies Thru Small Bore (thru ) Construction: Smooth tube of anti-static (conductive) Teflon. Braid(s) reinforcements of densely packed, high tensile Type 04 stainless steel wire. Reinforcement design varies size by size. Fittings are Type 6 stainless steel. Operating temperature range: -6 F (-4 C) to 400 F (204 C) Features/applications: Non-aging hose designed for high pressure hydraulic or pneumatic service. Non-stick Teflon surface ideal for viscous material transfer. Teflon also minimizes pressure drop loss. Exceeds SAE 00R8 and SAE 00R9 standards. Flexible, chemically resistant, moisture resistant, low volumetric expansion. Max. Min. Burst Pressure Hose Nom. Operating (psi) Min. Nom. Size Hose Pressure Bend Size I.D. O.D. Room Temp. Room 400 F Radius (In.) (In.) (In.) (psi) Temp. (204 C) (In.) TH TH TH TH TH TH000 Teflon Hose Assemblies Fitting Options Female JIC Swivel Female Pipe FNPT Female O-ring Nom. Size (In.) Thread Nom. Size (In.) Thread N.A N.A. 4 N.A. Nom. Size (In.) Thread N.A N.A. 4 C.F. 4 C.F. Male NPT JIC Male NPT Union Nom. Size (In.) Thread Teflon is a registered trademark of the DuPont Co. Nom. Size (In.) Thread

100 SPECIAL APPLICATION HOSES, METAL & TEFLON HOSES Teflon Hose Assemblies Thru continued Covers Firesleeve/insulating sleeve: Protects hose from direct flame or external heat. Helps insulate workers from internal heat. Material is braided fiberglass tubing impregnated with silicone rubber (accessory code F). Anti-kink casing: Stainless steel armor prevents over bending/kinking of hose and provides chafe protection for the wire braid. Casing provides added safety allowing hose assembly to weep rather than rupture if for some reason tube should fail (accessory code A). How to Order Small Bore Number Example: 08TH020S6A 08 TH 02 0 S6 A Length Tube I.D. (In.) Hose Style Fitting One End Fitting Other End Fitting Material Accessory Code 04 ( 6)4 0 ( 6)4 08 ( 2) 0 ( 2)44 2 ( 8)44 6 ( 7 8)44 TH 02 = Female JIC 0 = Male Pipe NPT 06 = Female Pipe FNPT 08 = JIC/Male Union = O-ring Type 6 stainless steel A = Armor Casing C = Armor Cuffs F = Firesleeve Teflon is a registered trademark of the DuPont Co. 00

101 Large Bore Convoluted Tube (/8 thru ) SPECIAL APPLICATION HOSES, METAL & TEFLON HOSES Teflon Hose Assemblies 8 Thru Teflon tube Pure Teflon: white or static dissipating conductive. WSC: natural white Teflon tube. BCS: conductive tube to 0-6. Both tubes are low profile, self-draining, helical convolution form. Neutral to taste, color or odor. Non-stick, non-contaminating tube cleans easily. Steam, detergent or caustic cleanable. Temperature rating: -00 F (-7 C) to 40 F (22 C). Reinforcement High tensile Type 04 stainless steel braided. Working pressure based on minimum 4: safety factor; burst to suggested maximum working pressure. Approvals FDA (Food and Drug Administration). United States Pharmacopeia Class VI. Fittings: Over 0 stocked styles. Min. Operating Rated Min. Vacuum Pressure Operating Bend Resistance* Size I.D. O.D. Room Temp. Pressure Radius (In. of (In.) (In.) (In.) (psi) (psi) (In.) Mercury) Full 2706 WCS or BCS Full 2708 WCS or BCS Full 272 WCS or BCS Full 276 WCS or BCS WCS or BCS WCS or BCS WCS or BCS For styles above 2 I.D. consult literature regarding TWOB or TBOB Series Hose. *Vacuum resistance measured with hose bent to 2x minimum bend radius, ambient temperature. Teflon is a registered trademark of the DuPont Co. 0

102 Teflon Smooth Tube SPECIAL APPLICATION HOSES, METAL & TEFLON HOSES Rubber Covered Teflon Smooth Tube Teflon tube Pure Teflon; white tube (TLCT). Unexcelled chemical resistance. Compatible with all material. Easy to clean. Assured sterility. Non-stick smooth tube. Can be cleaned with steam, caustics, solvents or other cleaning agents. Durable, kink resistant with no external wire reinforcement to potentially fray. Full vacuum rated. The most flexible, smooth tube Teflon design. Temperature rating: -40 F (-40 C) to 0 F (77 C) Has has successfully passed internal steam tests at 406 F (208 C). Construction: Smooth tube internally bonded to a rubber hose type construction. Multiple reinforcement, double helix wire supported. Chemically resistant, ozone and abrasion resistant cover. Approvals FDA (Food and Drug Administration). United States Pharmacopeia Class VI. Fittings: Over 6 styles of stocked crimp design. Flare thru TM designs available. Bolt-on or clamped fitting styles optional. Recommended Min. Size Size Working Bend I.D. Nom. O.D. Pressure Radius (In.) (In.) (psi) (In.) TLCT/WTLCT TLCT/WTLCT TLCT/WTLCT TLCT/WTLCT TLCT/WTLCT TLCT/WTLCT TLCT/WTLCT TLCT/WTLCT TLCT/WTLCT Teflon is a registered trademark of the DuPont Co. 02

103 SPECIAL APPLICATION HOSES, METAL & TEFLON HOSES Convoluted and Rubber Covered Teflon Hose How to Order OVERALL LENGTH inside diameter (I.D.) hose with male NPT fitting one end and cam-lock coupler ( D ) fitting other end. Fitting materials: Type 6 stainless steel. Number Example: 6WCS06S6-L 6 WCS 0 6 S6 ( ) Length Size I.D. (In /6 ) Hose Style Fitting One End Fitting Other End Fitting Material Accessory Code 06 ( 8) 08 ( 2) 2 ( 4) 6 () 20 ( 4) 24 ( 2) 2 (2) TLCT Size 08 ( 2) 2 ( 4) 6 () 20 ( 4) 24 ( 2) 2 (2) 40 (2 2) 48 () 64 (4) WCS BCS Also available with nonmetallic braids. TLCT Hose Style TLCT WTLCT 0 = Butt Weld Adapter, Pipe 02 = JIC Female 0 = Male Pipe, NPT 06 = Female Pipe, FNPT 07 = JIC/Female Union 08 = JIC/Male Union 0 = Sanitary, Gasket Style 0U = Sanitary, Step-Up = Sanitary, Mini Style *2 = Flange Retainer, Lap Joint Style *6 = Cam-lock Coupler ( D ) *7 = Cam-lock Adapter ( E ) *8 = Cam-lock x Flange Adapter 20 = Sanitary, Bevel Seat w/nut = Compression Connector FN = Compression Connector w/nuts & Ferrules 2 = Compression Adapter 2FN = Compression Adapter w/nuts & Ferrules = O-ring Female Adapter 8 = JIC Male 40 = Sanitary, Bevel Seat, Exposed Thread 4 = Butt Weld Adapter, Tube 44 = O-ring Male 0 = I-Line Sanitary Male = I-Line Sanitary Female 6 = NPSH Female Swivel *Teflon Encapsulated style also available. st Letter: Ferrule Material 2nd Letter: Fitting Material rd Letter: Flange Material C = Steel M = Monel 6 = 6 SS T = Teflon Encapsulated P = Polypropylene V = PVDF (Kynar) (4) = Flanges Only 04 SS (6) = Flanges Only 6 SS Length Tolerance A = Armor Casing C = Casing Strain Cuffs F = Firesleeve H = Hypalon Chafe Sleeve S = External Spring Guard 4 (.20) on assemblies to 24 2 (.00) on assemblies 2 to 60 % on assemblies over 60 Teflon is a registered trademark of the DuPont Co. 0

104 SPECIAL APPLICATION HOSES, METAL & TEFLON HOSES Large Bore Teflon Fittings Selection Pipe Thread (NPT) Male Style 0 Flanges Lap Joint Flange Style 2 Shown with epoxy coated steel flange Cam and Groove Female Swivel Type Style 6 Also available Teflon Encapsulated Style 6T and Flare-Thru TM design Male Union Style 08 Female Style 06 Teflon Encapsulated Style 2T Available Flare-Thru TM design Gasket Style 66T Teflon Encapsulated Gasket Silicone Center completely encased with Teflon Male Style 7T Stainless steel version Style 7 Female Union Style 07 JIC Female Swivel Style 02 Cam by Flange Adapter Teflon Encapsulated Style 8T Stainless steel version Style 8 Some sizes also available in plated steel material. Male Style 8 Teflon is a registered trademark of the DuPont Co. 04

105 SPECIAL APPLICATION HOSES, METAL & TEFLON HOSES Large Bore Teflon Fittings Selection continued Sanitary Mini Sanitary Style Compression Compression Tube Adapter Style 2 Butt Weld Tube Butt Weld Style 4 Tri-Clamp Style 0 Available Flare-Thru TM design Tube Adapter with Nut and Ferrule(s) Style 2 FN Pipe Butt Weld Style 0 Bevel Seat with Nut Style 20 Tube Connector Style O-ring Female with Nut Style Bevel Seat Male Style 40 Tube Connector with Nut and Ferrule(s) Style FN Male Style 44 I-Line Male Style 0 Available Flare-thru TM design Tri-Clamp is a registered trademark of Ladish Co.; I-Line is a registered trademark of Cherry Burrell Corp. and Teflon is a registered trademark of the DuPont Co. 0

106 SPECIAL APPLICATION HOSES, METAL & TEFLON HOSES Expansion Joints Rubber, Teflon /Metal Rubber Expansion Joints All designs available: Spool-Type, Wide Arch, Spherical, Low Spring Rate Type. In-stock sizes range from to 72 I.D. Manufacturing capability to 44 I.D. (Tooling is available to manufacture all non-stock sizes.) 0 sizes of concentric and eccentric expansion joint reducers. Modifications to design include: Multi-Arch and Filled-Arch. Standard Elastomers include: Butyl, Neoprene, Nitrile, Hypalon, Natural, EPDM, Viton and FEP. U-Type expansion joints are manufactured in Rectangular, Oval and Round configurations with internal or external flanges or Turbine/ Condenser or Piping/Ducting services. Spherical Design Wire Arch Design Spool-Type Concentric Reducer Eccentric Reducer Lateral/Axial Offset Teflon and Viton are registered trademarks of the DuPont Co. 06

107 SPECIAL APPLICATION HOSES, METAL & TEFLON HOSES Expansion Joints Rubber, Teflon /Metal continued Expansion Joints Handbuilt Heavy Duty Low Torque Gaskets Rubber Pipe/ Vibration Dampeners Expansions Joints Molded Spherical, Single and Double Economical For Plastic, Fiberglass, Glass or other piping which require minimum sealing forces. Manufactured in EPDM (with peroxide cure) and EPDM (with PTFE Film). In-stock sizes are available from 2 to 2 I.D. Teflon Expansion Joints For Vibration/Noise Reduction or lateral movements. In-stock sizes from to 24 I.D. in lengths from 2 to 48. Standard Elastomers are Neoprene and Butyl, other elastomers are available. Flexible Metal Hose Connectors Handbuilt and Molded Non-metallic Expanision Joints are designed for tough demanding industrial applications, as found in: Air Conditioning- Heating and Ventilating Systems, Chemical-Petrochemical and Industrial Process Piping Systems, Power Generating Plants, Steel Mills, Marine Services, Pulp/Paper Systems, Water- Wastewater-Sewage and Pollution Control Systems. Installed next to mechanical equipment or between the anchor points of a piping system to: Absorb pipe movement/stress. Reduce system noise. Isolate mechanical vibration. Compensate alignment/offset. Eliminate electrolysis. Protect against start-up/surge forces. Teflon and Viton are registered trademarks of the DuPont Co. Called: Couplings, Expansion Joints or Bellows. In-stock sizes ranging from to 2 in 2, and convolutions with PFA Teflon. Also available in PTFE Teflon with in-stock sizes ranging from 4 to 24 I.D. in and convolutions. Designed primarily for chemical services, the inexpensive cost and short face-to-face lengths make this product universal in application. Metal Expansion Joints High Corr or Low Corr. Modifications to design include: Universal and Tied. Available with flanged or welded ends. Single or Multi-ply Bellows construction. Standard bellows material is 04 or 2 stainless, but available in a variety of exotic metals. Sizes from to 24. Wire braid covered annular corrugated hose of stainless steel or bronze is stocked in I.D. sizes to 4. Available with flanged, welded or threaded ends. Special hose assemblies can be manufactured to customer specifications with: One Braid or Two Braids and a selection of end fittings. Non-Metallic Expansion Joints/Fan Connectors A complete line of ducting expansion joints available in round or rectangular sizes with flanged or flat belt profiles for fan inlet and discharge applications. For applications in: Chemical/ Petrochemical, Industrial, Power, and Pulp and Paper industries. Elastomeric elements are offered for systems operating below 400 F and are manufactured of Viton, Butyl EPDM or other elastomers. 07

108 SPECIAL APPLICATION HOSES, METAL & TEFLON HOSES Expansion Joint Specification Sheet Company Name MISCELLANEOUS MOVEMENTS PRESSURES FLOWING MEDIUM SIZE YOUR COMPANY Mailing Address City, State, Zip Code Item No. Tag No. Item No. Tag No. Item No. Tag No. Name of Person Submitting Data Phone No. Quantity Required Quantity Required Quantity Required Pipe Size of Application Nominal pipe size or the inside diameter of the connecting pipe flange Installed Length is the space between connecting pipe flanges. Indicate limitations, if any. Flowing Medium Indicate chemical. If flowing medium is corrosive, abrasive, or viscous, explain in detail. Type of Medium Indicate if liquid, gas, slurry, solids, etc. Inches Inches Inches Inches Inches Inches Temperature of Flowing Medium Operate Maximum Operate Maximum Operate Maximum Indicate both operating and maximum temperatures at the expansion joint. F F F F F F Temperature of Surrounding Atmosphere Minimum Maximum Minimum Maximum Minimum Maximum Indicate both minimum and maximum temperatures of atmosphere at the expansion joint. F F F F F F Time Duration at Maximum Temperature Indicate length of time. Velocity of Flowing Medium In feet per minute. Ft/Min Ft/Min Ft/Min Operating Pressure at the Joint Positive Negative Positive Negative Positive Negative Actual pressure in which system works in normal conditions. PSIG Hg PSIG Hg PSIG Hg Design Pressure of the System Positive Negative Positive Negative Positive Negative Highest/most severe pressure expected during operation. PSIG Hg PSIG Hg PSIG Hg Surge Pressure of the System Positive Negative Positive Negative Positive Negative Increased pressure due to pump starts, valve closings, etc. PSIG Hg PSIG Hg PSIG Hg Test Pressure of the System Positive Negative Positive Negative Positive Negative Hydrostatic test used to demonstrate system capability. PSIG Hg PSIG Hg PSIG Hg Type of Pressure Constant, intermittent, shock, pulsating, etc. Axial Compression at Joint In inches as a result of pipe extension expansion. Actual Elongation at Joint In inches as a result of pipe contraction. Lateral Deflection at Joint In inches. Angular Movement at Joint In degrees. Inches Inches Inches Inches Inches Inches Inches Inches Inches Degrees Degrees Degrees Torsional Movement at Joint In degrees. Degrees Degrees Degrees Pipe Flange Drilling Specification Specification Specification Indicate specific standard such as 0# ANSI B 6.. If special, provide: Flange O.D., Bolt, Circle, Number and Size of Holes. Mating Pipe Flange Thickness In inches. Inches Inches Inches Location of Joint Installation Indoors or outdoors. Retaining Rings Yes or No Yes or No Yes or No Are required on all installations. Reusable, they need not be ordered with replacement or spare expansion joints. Control Unit Assemblies Yes or No Yes or No Yes or No Are recommended for use in all expansion joint applications. Control units must be used when piping support or anchoring is insufficient. Hydrostatic Test of Joint Required by Manufacturer of Product Yes or No Yes or No Yes or No Complete and Mail to Summers Rubber Co. Photocopy this form for additional copies. 08

109 DUCTING HOSE Flexible Hose and Ducting Hose RFH RFH-W UFD Constructed of thermoplastic rubber and reinforced with a wire helix, RFH is the most versatile general purpose hose available today. No cements, solvents, chemicals, adhesives or glues are used in the manufacturing process. RFH has superior chemical resistance and is capable of handling fumes as tough as methyl ethyl ketone, sulfuric acid or toluene. Excellent ozone resistance; good abrasion resistance; low compression set. RFH can be manufactured in other colors, and can also be supplied with a color stripe. Please consult us for minimums and prices for other lengths and non-standard diameters. Standard lengths: 2, 0 and 00. Temperature range: -60 F to 27 F (- C to + C) continuous service, intermittent to 00 F (49 C). Sizes: 2 through 20. Standard color: Black. RFH04 RFH04 is a heavier version of RFH. For applications involving higher pressures or more severe abrasion, RFH04 is an ideal solution. Constructed in the same manner as RFH, RFH04 has higher pressure capability at elevated temperatures. RFH04 has the same characteristics as RFH and is available in other sizes. Standard sizes: 4, 6, 8, 0 and 2. Vacuum Hose Vent Hose RFH-W is identical to RFH except for an external orange wearstrip which covers the wire. This wearstrip helps prevent premature wire wear-through in the case of dragging or rough use. No cements, solvents, adhesives, glues or chemicals are used in the manufacturing process, thus the wearstrip will not come off or delaminate. The RFH-W wearstrip is molecularly bonded to the hose wall. Sizes up to 20 are available, ask about minimums. Standard sizes: 2 through 2. RFH-White RFH-White is identical to RFH in all of its characteristics except that its color is white. RFH-White is suitable for those applications where a white hose is desirable such as pharmaceuticals or food. Materials used in RFH-White are FDA acceptable. Standard sizes: 2,, 4,, 6, 8 and 0. Standard length: 2. Constructed of thermoplastic urethane and reinforced with a wire helix, UFD offers superior abrasion resistance. UFD is the answer for those who want a lightweight, flexible hose which can handle much abrasion. UFD can be used in numerous applications such as leaf loading, chip handling, dust collection, straw blowing, etc. The superior transparency of the clear UFD allows users to locate blockages. Consult us about non-standard diameters and lengths. Heavier or lighter versions are available for specific applications. Special colors are also available. Standard lengths: 2 or 0. Temperature range: -6 F to 200 F (-4 C to +9 C). Sizes: 2 through 8. Colors: Clear or Black. Leaf Collection Hose 09

110 DUCTING HOSE Flexible Hose and Ducting Hose continued CVD ARH J- Constructed of polyvinylchloride (PVC) and reinforced with wire, CVD is an excellent choice for many industrial applications. CVD is an economical alternative to most ducts and sacrifices nothing in performance. CVD is an excellent choice for applications involving fume removal, dust collection, ventilation and other more rigorous industrial requirements. Material used in clear version is FDA acceptable. Consult us about non-standard diameters and lengths. Special colors are also available. Standard lengths: 2 and 0. Temperature range: -20 F to 80 F (-29 C to +82 C) Sizes: 2 through 8. ARH has a smooth interior, for easier flow and resistance reduction. Constructed of a thermoplastic rubber, ARH offers many of the same properties as our RFH, including: excellent chemcial, ozone and UV resistance. There is no wire in ARH, allowing for much better crush resistance and good memory should the hose become accidentally crushed. The external helix allows for rough use or applications where the hose will be dragged. ARH is constructed without the use of solvents, adhesives, chemicals or glues; the external helix is molecularly bonded to the tube it will not come off or delaminate. Materials used in the white version are FDA accepted. Standard lengths: 2 and 0 (cut lengths on request). Temperature range: -60 F to 27 F (- C to + C) continuous service, intermittent to 00 F (49 C). Sizes: 4 through 4. Standard Color: Black with gray helix. Consult us about other colors. J- is an all-polyethylene hose with a smooth interior. It is a very economical choice for low pressure fume or ventilation applications. The all plastic construction gives the hose good memory to resist permanent crushing. J- can be manufactured with special integral cuffs, providing added strength and neater terminations. Variations of the J- allow us to provide special colors, diameters, lengths and widths. Good UV resistance and very flexible and economical. Material used in the clear version is FDA accepted. Standard lengths: 2 and 0 (cut lengths on request). Temperature range: -0 F to 60 F (-4 C to +7 C). Sizes: 4 through 4. Color: Black. 0

111 DUCTING HOSE Flexible Hose and Ducting Hose continued PFR TBH is an all plastic hose constructed of a clear polyethylene copolymer wall reinforced with a polyethylene helix. is used in numerous applications including tobacco stem collection, insulation blowing, dust collection and fume removal; can be supplied in a heavier or lighter version, satisfying specific application requirements. Good abrasion resistance. Material used in the clear version is FDA accepted. Standard Lengths: 2 and 0 (cut lengths on request). Temperature range: -0 F to 0 F (-4 C to +4 C). Sizes: through 4. Color: Clear wall with opaque helix. SPR Constructed of polyvinylchloride (PVC) and reinforced with wire, PFR is an excellent choice for shipyard ventilation applications. PFR is completely self extinguishing since it is manufactured with UL94 V-O materials. PFR is an economical alternative to neoprene coated fabric ducts which are commonly found at most shipyards. Good abrasion and weathering resistance. PFR can be supplied in other sizes and colors. Please consult us about minimums. Standard lengths: 2 or 0. Temperature range: -20 F to 80 F (-29 C to +82 C). Standard sizes: 4, 6 and 8. Color: Light Blue. ARD A low cost general purpose hose with excellent tear resistance, great flex fatigue resistance, with good abrasion, chemical and moisture resistance. Standard lengths: 2, 0, other lengths up to 00 available. Temperature range: -40 F to 22 F (-40 C to +07 C). Standard sizes: 2, 2 2,, 4,, 6, 7, 8, 0 and 2. TBH-W Constructed of a thermoplastic elastomer and wire reinforced, SPR offers durability and economy. SPR-W is offered with an orange external wearstrip. The flex fatigue and abrasion resistance of SPR and SPR-W are superior to that of most rubber compounds or conventional plasticized PVC compounds, neoprene or EPDM. Ask us about minimums for weights and sizes. Standard lengths: 2 or 0. Temperature range: -0 F to 80 F (-4 C to +82 C). Stock sizes: For SPR020 Stock sizes: through 8. Stock sizes: For SPR-W0 4. Color: Black for SPR, and Black w/orange wearstrip for SPR-W. Constructed of a clear polyvinylchloride (PVC) wall and wire reinforced, ARD is an economical choice for moving large volumes of air. ARD is highly retractable, very flexible and sturdy. ARD is reusable and handles more CFM. It is priced to compete favorably against other wide-pitch fabric ducts. Good chemical resistance. Non-standard diameters, special colors and special lengths are available. Standard lengths: 2 and 0. Temperature range: -20 F to 80 F (-29 C to +82 C). Standard sizes: 8 through 8. Color: Clear. All the characteristics of TBH and with the addition of a wearstrip this hose has even greater wear resistance in applications where the hose may be dragged. Standard lengths: 2, 0, other lengths up to 00 available. Temperature range: -40 F to 22 F (-40 C to +07 C). Standard sizes: 2, 2 2,, 4,, 6, Swimming Pool

112 DUCTING HOSE Flexible Hose and Ducting Hose continued TBH-AP CWC Duct Hose Bendway S An all polypropylene hose with no wire helix but this hose can be crushed and it will return to its original shape. Smooth interior hose with all the excellent characteristics of TBH. Standard lengths: 2 and 0. Temperature range: -40 F to 200 F (-40 C to +9 C). Standard sizes:, 4,, 6, 7, 8, Silfab, Silicone Hose Neoprene coated polyester fabric, two ply with steel helix wire. Temperature range: -40 F to 20 F (-40 C to +2 C). I.D. sizes: 4 to 6. Standard lengths: 0, and 2. Color: Black. Light Weight Plastic Vacuum Hose Type K For hot air and fume applications. Resists corrosive fume attack. Wide temperature capabilities; can be bent, straightened, and cut. Material: 04 stainless steel;.00 thick. Flex: Hand bendable. I.D. sizes: 2 to 2. Standard length: 0. Temperature range: -200 F to 800 F (- C to +426 C). Bendway A Silicone, temperature rated. Silicone coated fiberglass. Resists extreme temperatures. Steel wire helix with filament fiberglass cord. Applications: For hot or cold air handling, fume removal or ventilation from dryers, tanks or enclosures. Low pressure handling of gaseous materials. Silfab series resists extreme temperatures, fungi, and ozone. Fair resistance to alkalies, water, oils and solvents. Characteristics: Very flexible at low temperatures. Odor free in hot air service. Excellent electrical properties. Silfab 2 Standard fiberglass coated with silicone, two ply. Temperature range: -6 F to 0 F (-4 C to +287 C). I.D. sizes: to 2. Crush-proof, all-plastic hose. Offers superior flexing characteristics and abrasion resistance. After crushing or kinking, will regain its original shape. Material: Plastic. Flex: Very flexible. I.D. sizes: 4, 2, 4, 2, 2 4, 2 2 and. Standard length: 0. Temperature range: -6 F to 40 F (-4 C to +60 C). End fittings available. For hot air and fume applications. Resists corrosive fume attack. Wide temperature capabilities; can be bent, straightened, and cut. Material: Aluminum alloy;.008 thick. Flex: Hand bendable. I.D. sizes: 2 to 2. Standard length: 0. Temperature range: -00 F to 400 F (-7 C to +204 C). Silfab 2 is a registered trademark of Flex Fab Corporation. 2

113 DUCTING HOSE Rubber Convoluted Garage Exhaust Hose Precision The Vacuum Mandrel Process creates a precise patterned spiral convolution. 00% Recovery Convolutions made by the unique manufacturing process ensures 00% hose recovery. This means return to original shape after hose has been depressed. Material Special high performance rubber compounding techniques have been used to obtain the optimum physical properties for this demanding application. The selected EPDM polymer when combined with other critical ingredients provides the resistance to heat, aging and fumes encountered in today s service conditions. Greater Flexibility Uniform wall thickness permits severe distortion and bending of the garage exhaust hose without collapsing or kinking. Description Dia. (In.) x Lgth. (Ft.) No. 2 x 0 22 GE 2 2 x GE x 0 2 GE 4 x 0 24 GE x 0 2 GE Rubber Convoluted Garage Exhaust Hose Accessories Universal Adapter 9264 Dual Tailpipe Adapter 97 Door Port 926 Special rubber adapter will fit most automobiles. Adjustable, accepts either 2 2 or hose. Aluminum Y Adapter 926 This adapter is designed for use on cars equipped with side-by-side dual exhaust pipes. Used with or 4 hose. Diesel Elbow Adapter 9262 Rugged aluminum door port is easy to install and has a gravity door which shuts when not in use. For doors up to thick, accepts 2 and 2 2 hose. Garage Exhaust Hose Easy Assembly Can be used with 2 or 2 2 hose from two tailpipes and 2 2 or hose to the system outlet. For diesel stacks. Designed with air draft space to help reduce heat. Used with 4 and hose. 0 lengths couple together by squeezing one end and inserting into another end and releasing.

114 DUCTING HOSE Flexible Hose and Ducting Hose Summary X Indicates I.D. Availability Basic Drag Severe Basic FDA Metal Duct Hose Garage Lower Temperature Leaf/Chip High Heat Duct Protection Abrasion Duct Approved High Heat Exhaust Economical Light Wire/ Clear/ Duty Size Standard- Heavy Duty 22 Wear- No Abrasion No Standard Aluminum Stainless Standard Clear Industrial I.D. Standard Wearstrip Higher psi w/wire strip Wire Resistant Wire White 0 Bendway Bendway Garage PVC PVC Duct (In.) RFH RFH-W RFHO4 TBH TBH-W TBH-AP UFD-C ARH RFH-White Silfab 2 Type A Type S Exhaust ARD CVD 4 X X 4 X X 4 X X 2 X X 4 X X 2 4 X X X X X X X X X X X X 2 4 X X 2 2 X X X X X X X X 2 4 X 4 X X X X X X X X X X X X X 4 X 2 X X X X X 4 2 X X X X X X X X X X X X 4 2 X X X X X X 2 X X X X X X X X X 2 X X X X 6 2 X X X X X X X X X X X 7 2 X X X X X X X X 8 2 X X X X X X X X X X X 9 2 X X X X 0 2 X X X X X X X X X X X X X 2 2 X X X X X X X X X X 4 2 X X X X 6 2 X X X X 8 2 X X X X 20 2 X How to Order Ducting Hose I.D. Size Style Length Example: 2 RFH 2 4

115 DUCTING HOSE Custom Built Flexible Ducting End Finishes Accessories Ys, Ts and Branches Fabric Cuffs Steel Flanges Available in 2,, 4, 6, 8, 0 and 2 I.D. Eliminates need for backup plates. Ys Enlarged Cuffs Felt Flanges Neoprene-impregnated. Available in sizes from 2 through 24 I.D. Ts Made to order from galvanized sheet metal, neoprenecoated. Reduced Cuffs Reducers Made to order from galvanized sheet metal, neoprenecoated. Branches Transition Cuffs Transitions Made to order from galvanized sheet metal, neoprenecoated. Added Coatings/Dippings: Neoprene Most frequently used coating to resist weathering and abrasion. Buna N Superior to neoprene in applications involving specific chemicals, solvents, and oils. Polyurethane Produces smooth, high gloss surface. Resistance to abrasion, oxidation, ozone, and solvent attack. Not recommended for wet service.

116 DUCTING HOSE Fiberglass Sleeving, Rope and Tape for High Heat Applications Silco Sleeve High Grade Silicone Rubber Bonded to Fiberglass Sleeving. Fiberglass Rope and Tape Designed for Hot Process Applications Silco Sleeve is designed to protect wires, hoses, and cables from the hazards of high heat and occasional flame. Protects continuously to 00 F. Made of braided fiberglass yarn in a flexible sleeve form, then coated with high grade silicone rubber. Resistant to hydraulic fluids, lubricating oils, and fuels, and allows qualified hose assemblies to pass the SAE Aerospace Standards 0B testing under stated flow and pressure conditions. Nominal I.D. (In.) No. 4 4 Silco Sleeve 4 4 Silco Sleeve 2 2 Silco Sleeve Silco Sleeve 2 Silco Sleeve 24 Silco Sleeve 2 Silco Sleeve Also available in odd sizes 4 increments from 4 to. Applications Boiler doors. Wood stove doors. Industrial oven doors. Pollution control equipment doors. Aluminum crucible packing. Coke oven doors. Tadpole tape core rope. High temp filter bag retaining cord. Wicking. Pipe wrap. Tying and lacing cord. Other product options Wire jacketed rope. Silicone coated rope. Overbraided sizes available from 2 to 4. Tadpole tapes. Weld back tape. Wicks. Silco Sleeve is a registered trademark of Davlyn Manufacturing Co., Inc. 6

117 QUICK DISCONNECTS Twin-Kam Kamlok Couplers Standard Items Dust Plug Series 64-A Stainless Size Aluminum Brass Steel (In.) No. -AL -BR -SS A X X X A X X X A X X X A X X A X X X A X X X A X X A X X X A X X X A X Dust Cap Series 64-B Stainless Size Aluminum Brass Steel (In.) No. -AL -BR -SS B X X X B X X X B X X X B X X X B X X X B X X X B X X B X X X B X X X B X B X Female NPT Adapter Series 6-A Twin-Kam Kamlok Couplers Stainless Size Aluminum Brass Steel (In.) No. -AL -BR -SS A X X X A X X X A X X X A X X X A X X X A X X X A X X X A X X X A X X X A X 46 6-A X Female NPT Coupler Series 6-D Stainless Size Aluminum Brass Steel (In.) No. -AL -BR -SS D X X X D X X X D X X X D X X X D X X X D X X X D X X X D X X X D X X X D X 46 6-D X Male NPT Adapter Series 6-F Stainless Size Aluminum Brass Steel (In.) No. -AL -BR -SS F X X X F X X X F X X X F X X F X X X F X X X F X F X X X F X X X F X Male NPT Coupler Series 6-B Stainless Size Aluminum Brass Steel (In.) No. -AL -BR -SS B X X X B X X X B X X X B X B X X X B X X X B X B X X X B X X X B X Twin-Kam and Kamlok are registered trademarks of Civacon. 7

118 QUICK DISCONNECTS Twin-Kam Kamlok Couplers continued Hose Shank Adapter Series 6-E Stainless Size Aluminum Brass Steel (In.) No. -AL -BR -SS E X X X E X X X E X X X E X X X E X X X E X E X E X X X E X X X E X 46 6-E X Coupler Hose Shank Series 6-C Stainless Size Aluminum Brass Steel (In.) No. -AL -BR -SS C X X X C X X X C X X X C X X X C X X X C X X X C X X X C X X X C X X X C X 46 6-C X Also available in Malleable Iron and Polypropylene. Twin-Kam Kamlok Miscellaneous Couplers and Adapters Adapter and Coupler w/socket Welding End Series 6-AW & 6-DW Lockable Cap Series 64-BK DW AW Stainless Size Aluminum Steel (In.) No. -AL -SS 2 x AW X 2 x AW X X x.0 6-AW X x.0 6-AW X X 4 x AW X 4 x AW X X x AW X When ordering, size of bore (O.D. of tubing or pipe) must be specified. Stainless Size Aluminum Steel (In.) No. -AL -SS BK X X 64-BK X BK X X BK X Kamlok Coupler s Kits Guaranteed For Life [GFL] TM Twin-Kam Arms 8 s Kit includes: 2 Cam Arms, plus Pins, 2 Finger Rings and Instructions. Civacon Kamlok Coupler s Kits are packaged in convenient plastic pouches, pre-punched for easy hanging in stock room or display area. Our Strong Arm Guarantee: In the unlikely event a Guaranteed For Life [GFL] TM Twin-Kam Arm ever breaks Civacon will replace it Free of Charge no questions asked. Update your existing Civacon Kamlok Couplers by installing Guaranteed For Life [GFL] TM Twin-Kam Arms. CAUTION: We do not recommend the use of Twin-Kam Arms on couplers not manufactured by Civacon! Dimensional differences do exist and proper performance cannot be assured. Twin-Kam and Kamlok are registered trademarks and [GFL] is a trademark of Civacon. Aluminum, Stainless Sizes Brass Steel (In.) * 2 & 4* H982 H264 H98 H H829 H86, 4 & H487 H267 **6** H224 ** Finger Rings are not included with 2 and 4 Kit. ** 6 Cam Arms are bronze and do not have Twin-Kam and [GFL] feature. #Coupler, material of construction, not Twin-Kam Arm material.

119 QUICK DISCONNECTS Gaskets for Kam and Groove Fittings Compound 2 & Buna-N BG-07 BG-00 BG-2 BG-0 BG-200 BG-20 BG-00 BG-400 BG-00 BG-600 E.P.T. EG-07 EG-00 EG-2 EG-0 EG-200 EG-20 EG-00 EG-400 EG-00 EG-600 Neoprene NG-07 NG-00 NG-2 NG-0 NG-200 NG-20 NG-00 NG-400 NG-00 NG-600 White Neoprene WNG-07 WNG-00 WNG-2 WNG-0 WNG-200 WNG-20 WNG-00 WNG-400 WNG-00 WNG-600 Teflon* TG-07 TG-00 TG-2 TG-0 TG-200 TG-20 TG-00 TG-400 TG-00 TG-600 Viton-A VG-07 VG-00 VG-2 VG-0 VG-200 VG-20 VG-00 VG-400 VG-00 VG-600 Teflon Envelope Gasket (Buna Filled) Teflon Envelope Gasket (Viton Filled) TBG-07 TBG-00 TBG-2 TBG-0 TBG-200 TBG-20 TBG-00 TBG-400 TBG-00 TBG-600 TVG-07 TVG-00 TVG-2 TVG-0 TVG--200 TVG--20 TVG-00 TVG-400 TVG-00 TVG-600 * Solid Teflon gasket recommended for use with viscous fluids only. Other gaskets such as Silicone and Compar are available. Pressure Ratings for Kamlok Fittings Aluminum, Brass and Stainless Steel Working Pressure Size up to 200 F (In.) (psi) Accessories Description Size No. Brass Security Chain (w/ S Hooks) 6 Long H06682M 2 Long H0668M Cadmium Plated Security Chain (w/finger Chain) 2 Long H46 Finger Ring 2 2 H64M Up H792M Paddle Cam Arm provides extra leverage (Bronze only) 4 Description Type Paddle Cam Arm Coupler H286 H286 Dust Cap H287 H287 Caution: Civacon Kamloks are recommended for use in handling liquids and non-compressible fluids. The use of Kamloks for handling compressible media such as air or steam, can create a hazardous condition and serious injury may occur to the operator, should the fittings be uncoupled while the line is under pressure. Civacon Kamlok fittings are capable of handling compressed media within the pressure and temperature limitations, however, no warranty is expressed or implied by Civacon as to their suitability or fitness for any particular use. Civacon products should be used in compliance with applicable federal, state, and local laws and regulations. Product selection should be based upon physical specifications, limitations, and compatibility with the environment and material to be handled. Kamlok is a register trademark of Civacon. Teflon is a registered trademark of the DuPont Co. 9

120 QUICK DISCONNECTS Autolok TM Self-Locking Quick Coupler Autolok Couplers and Caps CL Coupler Hose Shank 7DL Coupler Female NPT 7BL Coupler Male NPT 7DCL Coupler Dust Cap Autolok is a trademark of Civacon. Stainless Steel Autolok Couplers and Caps Are Available in the Following Sizes and Configurations: 7CL SS 4 7CL SS 2 7CL SS 2 7CL SS 7CL SS 7DL SS 4 7DL SS 2 7DL SS 2 7DL SS 7DL SS 7BL SS 4 7BL SS 2 7BL SS 2 7BL SS 7BL SS 7DCL SS 4 7DCL SS 2 7DCL SS 2 7DCL SS 2 2 7DCL SS 7DCL SS 4 7DCL SS 90 Adapter x Female NPT Series 90PPA Cam and Groove Polypropylene Elbows 90 Coupler x Female NPT Series 90PPD Size (In.) No. 2 90PPA PPA200 Size (In.) No. 2 90PPD PPD Coupler x Hose Shank Series 90PPC Size (In.) No. 2 90PPC PPC Adapter x Male NPT Series 90PPF Size (In.) No. 2 90PPF PPF200 Pressure Ratings The polypropylene Couplers and Adapters are recommended for a maximum working pressure of 2 psi ( 2 ), 00 psi ( 2 2 ) and 7 psi ( ). Recommendations based on the use of mating fittings at an ambient temperature of 70 F with standard seal installed. Fittings are manufactured from a glass-filled polypropylene. Couplers supplied with EPR gaskets and 04 Stainless Steel handles. For use at elevated temperatures or other unusual operating conditions, consult factory. Polypropylene is not recommended for use with Teflon gaskets. Teflon is a registered trademark of DuPont Co. 20

121 QUICK DISCONNECTS Polypropylene Cam and Groove Fittings Male Adapter x Female NPT Type A Size (In.) No. 4 x 2 2 APO 4 4 APO 4 4 APO 2 x 4 4 APO 2 2 APO APO 4 4 APO Male Adapter x Hose Shank Type E Size (In.) No. 4 x 2 2 EPO 4 4 EPO 4 4 EPO 2 x 4 4 EPO 2 2 EPO EPO 4 4 EPO Female Coupler x Male NPT Type B Size (In.) No. 4 x 2 2 BPO 4 4 BPO 4 4 BPO 2 x 4 4 BPO 2 2 BPO BPO 4 4 BPO Male Adapter x Male NPT Type F Size (In.) No. 4 x 2 2 FPO 4 4 FPO 4 4 FPO 2 x 4 4 FPO 2 2 FPO FPO 4 4 FPO Female Coupler x Hose Shank Type C Size (In.) No. 4 x 2 2 CPO 4 4 CPO 4 4 CPO 2 x 4 4 CPO 2 2 CPO CPO 4 4 CPO Dust Plug Type P Size (In.) No. 4 4 DPPO 4 4 DPPO 2 2 DPPO DPPO 4 DPPO Female Coupler x Female NPT Type D Size (In.) No. 4 x 2 2 DPO 4 4 DPO 4 4 DPO 2 x 4 4 DPO 2 2 DPO DPO 4 4 DPO Dust Cap Type H Size (In.) No. 4 4 DCPO 4 4 DCPO 2 2 DCPO DCPO 4 DCPO Note: The coupler and adapter portions of the 4 size use the 2 standard body size. Note: The coupler and adapter portions of the 2 size use the 4 standard body size. 2

122 QUICK DISCONNECTS Cam and Groove Reducing Adapters and Couplers Reducing Adapter x Female NPT Series A Stainless Size Aluminum Steel (In.) No. -AL -SS 2 x 200-A X X x A X X x A X 4 x 400-A X X 4 x A X 6 x A X X Reducing Coupler x Female NPT Series D Stainless Size Aluminum Brass Steel (In.) No. -AL -BR -SS 2 x 2 0-D X X 22 x 2 20-D X X 2 x D X X X 24 x D X X X Reducing Adapter x Hose Shank Series E Stainless Size Aluminum Steel (In.) No. -AL -SS 4 x 400-E X X Reducing Coupler x Hose Shank Series C Stainless Size Aluminum Steel (In.) No. -AL -SS x C X X x C X 4 x 400-C X X Reducing Adapter x Male NPT Series F Stainless Size Aluminum Steel (In.) No. -AL -SS 2 x F X 22 x F X 2 x 2 0-F X X 2 x F X X 2 x F X 24 x F X X Reducing Coupler x Male NPT Series B Stainless Size Aluminum Steel (In.) No. -AL -SS 2 x B X X 22 x 2 20-B X X 22 x B X X 2 x B X X 2 x B X 24 x B X X Cam and Groove Reducing Couplers x Adapters Reducing Couplers x Adapters Series ADA Reducing Couplers x Adapters Series ADA-EZ Coupler Coupler Adapter Adapter Stainless Size Aluminum Steel (In.) No. -AL -SS 2 x ADA200 X X x 2 ADA020 X X x 4 ADA040 X X 4 x 2 ADA4020 X X 4 x ADA400 X X Stainless Size Aluminum Steel (In.) No. -AL -SS x 2 ADA020EZ X X 4 x ADA400EZ X X 22

123 QUICK DISCONNECTS Cam and Groove Reducing Couplers x Adapters continued Reducing Couplers x Adapters Series DA Coupler Adapter Mall. Stnls. Size Alum. Brass Iron Steel (In.) No. -AL -BR -MI -SS 2 x 2 0-DA X X 2 x 2 0-DA X X 2 x DA X X 22 x DA X X 22 x 2 20-DA X X 22 x DA X X Coupler Adapter 22 x DA X X 2 2 x DA X X 2 2 x 2 20-DA X X 2 x 2 0-DA X X 2 x DA X X X X 2 x DA X X 2 x DA X X X 24 x DA X X 24 x DA X X 24 x DA X X X X 24 x DA X X 24 x DA X X 2 x 2 00-DA X 2 x DA X 26 x DA X X 26 x DA X X X X Spool Adapters Series AA Cam and Groove Spool Adapters Mall. Stnls. Size Alum. Brass Iron Steel (In.) No. -AL -BR -MI -SS x 2 00-AA X x 4 2-AA X x 2 0-AA X X X 2 x 2 20-AA X X x AA X X X 22 x 200-AA X X X 22 x AA X X 2 2 x 20-AA X X 2 2 x AA X X x 2 00-AA X X X 2 x AA X X X x AA X X 24 x 400-AA X 24 x AA X X X x AA X X 2

124 QUICK DISCONNECTS Cam and Groove Spool Couplers Spool Couplers Series DD Coupler Boss-Lock Spool Couplers Series ADD Coupler Coupler Coupler Stainless Size Aluminum Steel (In.) No. -AL -SS DD X X 2 x 200-DD X X 200-DD X X DD X X Stainless Size Aluminum Steel (In.) No. -AL -SS ADD X X 2 x 200-ADD X X 200-ADD X X ADD X X Cam and Groove Lockable Dust Caps Lockable Dust Caps Series DC-L Aluminum and Brass Stainless Steel Stainless Size Aluminum Brass Steel (In.) No. -AL -BR -SS 2 200DC-L X X X 00DC-L X X X 4 400DC-L X X 6 600DC-L X 8 800DC-L X Cam and Groove Elbows 90 Adapter x Female NPT Series A-90 Stainless Size Aluminum Steel (In.) No. -AL -SS 2 0A-90 X A-90 X X 4 00A-90 X X A-90 X X 90 Coupler x Female NPT Series D-90 Stainless Size Aluminum Brass Steel (In.) No. -AL -BR -SS 4 00D-90 X 4 2D-90 X 2 0D-90 X D-90 X X X D-90 X 4 00D-90 X X X D-90 X X D-90 X 24

125 QUICK DISCONNECTS Cam and Groove Elbows continued 90 Adapter x Hose Shank Series E-90 Size Aluminum (In.) No. -AL 00E-90 X 4 400E-90 X 90 Coupler x Hose Shank Series C-90 Stainless Size Aluminum Brass Steel (In.) No. -AL -BR -SS 4 2C-90 X 2 0C-90 X C-90 X X X 4 00C-90 X X C-90 X X C-90 X X 90 Adapter x Male NPT Series F-90 Stainless Size Aluminum Steel (In.) No. -AL -SS 2 0F-90 X F-90 X X 2 x 2 20F-90 X 90 Coupler x Male NPT Series B-90 Stainless Size Aluminum Steel (In.) No. -AL -SS 2 0B-90 X B-90 X X 90 Coupler x Adapter Series DA-90 Stainless Size Aluminum Brass Steel (In.) No. -AL -BR -SS 2 0DA-90 X DA-90 X X 4 00DA-90 X X DA-90 X X X DA-90 X 90 Coupler x Coupler Series DD-90 Size Aluminum (In.) No. -AL 4 400DD-90 X 4 Coupler x Adapter Series DA-4 Stainless Size Aluminum Steel (In.) No. -AL -SS 4 400DA-4 X X 2

126 QUICK DISCONNECTS Cam and Groove Couplers & Adapters x 0# Flanged Drilling Adapter x 0# ASA Flange Drilling Series AL Mall. Stnls. Size Aluminum Iron Steel (In.) No. -AL -MI -SS 2 00-AL X 2 0-AL X AL X X 2 00-AL X X X AL X X AL X X Coupler x 0# ASA Flange Drilling Series DL Stainless Size Aluminum Steel (In.) No. -AL -SS 2 00-DL X 2 0-DL X DL X X 2 00-DL X X DL X X DL X X Cam and Groove Couplers & Adapters x Round Tank Truck Flange Adapter x Round Tank Truck Flange Series ALT Size Aluminum (In.) No. -AL 00-ALT X x ALT X ALT X ALT X Coupler x Round Tank Truck Flange Series DLT Size Aluminum (In.) No. -AL 00-DLT X x DLT X DLT X DLT X Gaskets Size O.D. I.D. Thickness (In.) Gasket (In.) (In.) (In.) No. Cork/Buna 8 28 Teflon Envelope with Klinger Filler Cork/Buna Teflon Envelope with Klinger Filler GTTFCB 6 00GTTFTK GTTFCB 6 400GTTFTK Cam and Groove Couplers & Adapters with Straight Pipe Thread (NPSM) For Delivery of Dry Goods Adapter Series AS Malleable Size Aluminum Iron (In.) No. -AL -MI AS X X Vegetable fiber gaskets are standard in threaded end. Boss-Lock Series ADS Stainless Size Aluminum Steel (In.) No. -AL -SS 4 ADS400 X X Coupler Series DS Malleable Size Aluminum Iron (In.) No. -AL -MI EZ Boss-Lock Series ADS-EZ Stainless Size Aluminum Steel (In.) No. -AL -SS DS X X 4 ADS400EZ X X Vegetable fiber gaskets are standard in threaded end. Replacement fiber gasket 400GAGFI. 26

127 QUICK DISCONNECTS Cam and Groove Specialty Items 00YDAAAL Aluminum 200YDAAAL Aluminum Type Description (In.) Type Description (In.) Y 2 Coupler x Adapter x Adapter Y 2 Coupler x 2 Adapter x 2 Adapter TAADAL Aluminum TAAMTAL Aluminum Type Description (In.) Type Description (In.) T 2 Adapter x 2 Adapter x 2 Coupler T 2 MNPT x 2 Adapter x 2 Adapter YFL Aluminum TLT Aluminum Type Description (In.) Y 4, Tank Truck Flanged, 4 x 4 x 4 Type Description (In.) T, Tank Truck Flanged, 4 x 4 x 4 T 4, Tank Truck Flanged, 4 x 4 x 4 0ALTAL Aluminum 2040ALTAL Aluminum Type Description (In.) Type Description (In.) A 2 Adapter x Tank Truck Flange A 2 Adapter x 4 Tank Truck Flange 400YDAAOD Aluminum 20TDA0AAL Aluminum Type Description (In.) Type Description (In.) Y Tank Truck Flanged Assembly, 4 Coupler x 4 Adapter x 4 Adapter T 2 Coupler x 2 Adapter x Adapter Note: Some parts have a colored anodized surface finish. 27

128 QUICK DISCONNECTS Dry Disconnect Couplings Dry Disconnect Couplings Series 700D Dry Disconnect Adapter Series 600AN The Kamvalok dry disconnect coupling continues to be the standard of the industry. It provides automatic closure from both directions the coupler and the adapter. It is still the first choice for loading/unloading operations and manifold mixing/blending. Sizes: 4, 2, 2 and Dry Disconnect Adapter Series 67ANF The Kamvalok coupler and adapter are designed with female threads and can be fitted to either a male pipe end or to a hose fitting. Flanged end adapters are made for specific operations, including in-plant and transportation. Sizes: 4, 2, 2 and Vapor Tank Truck Hose Dry Disconnect Series 27AVN The Civacon 67ANF dry disconnect adapter keeps hazardous chemicals and vapors in the line and out of the environment with an easy access connection for tank cars, tank trucks, intermodal tanks, and in-process operations. The 67ANF dry disconnect adapter is made specifically for applications using an ANSI flange. Features Raised face flange, or optional tongue and groove design. Connection with a D2000 TM actuating coupler or Kamvalok dry disconnect coupler (700 Series). Quick disassembly for easy cleaning. The 27AVN has easy access in recovering vapors and provides a dry disconnect connection for top or bottom loading/unloading tank truck operations. Features Vapor hose connection made with 2 Kamvalok dry disconnect or D2000 activating couplers. straight thread mounting with 2 dry disconnect cam and groove connection. Becomes a x 2 adapter for QRB valves. Low profile keeps fitting below rollover plane to minimize damage in case of rollover. Stays within IMO profile dimensions. Easy attachment to existing MC07, DOT407, MC2 and DOT42 trailers, no modification to trailer required. Quick-clean disassembly design. Dry Disconnect Coupling Actuators Series D2000 Kamvalok is a registered trademark and D2000 is a trademark of Civacon. If your application requires automatic closure from only one flow direction, the D2000 Actuator provides your best dry disconnect value. Ideal for vapor recovery and suction pump applications. The D2000 Dry Disconnect Coupling Offers Easy to clean design. Built-in valve. Low cost design. Heavy duty construction. Easy-to-use cam and groove design. Compatible with Kamvalok adapters. Simple design for reliable operation. Sizes: 2 and 2 28

129 QUICK DISCONNECTS Dry Disconnect Couplings Transport Series Elbow Swivel Coupler Series 7ES-72ES Kamvalok Dry Disconnects are used on multi-compartment petroleum, solvent, and chemical product delivery trucks with an onboard pumping unit. Features Built-in elbow and swivel for freedom of movement when used with a hose on tank trucks. Swivel end is 2 female NPT. Poppeted adapter and coupler minimizes product loss during routine disconnect. Built-in valve, no additional valve required. Quick disconnect, cam and groove style for ease of use. Automatic shut-off with accidental disconnect to minimize product loss. Size: 2 Dry Disconnect Adapter Series 6AN-62AN Features Poppeted adapter minimizes product loss. Built-in valve prevents spillage. Quick disconnect, cam and groove style for ease of use. Automatic shut-off on accidental disconnect. Sizes: 2 and Dry Disconnect Coupling Series 86 Dry Disconnect Coupling Series 866 Features Two-piece aluminum construction with a rotatable hardcoated adapter for longer life. One-piece heavy-duty poppet with an acetal resin bearing for smoother opening characteristics. Computer designed cam profile provides easy opening. Lighter weight Duratuff corrosion resistant lever. Designed in accordance with API RP-004 with a standard 4 TTMA flange. Mounting lugs provided for Model 00 brake interlock valve. Operating lever closes away from the operator with a minimal rotation for increased operator ease. Features Hard-coat anodized for longer wear. Designed in accordance with API RP-004 TTMA flange inlet. Acetal Resin Poppet Guide for smooth operation. Mounting lugs provided for Model 00 brake interlock valve. Kamvalok is a registered trademark of Civacon. A Petroleum Industry application for dispensing product from tank trucks. 29

130 QUICK DISCONNECTS Dry Disconnect Couplings Kamvalok Series Size Product (In.) Construction Seals No. Adapter 2, 2, Aluminum, Aluminum Zinc Buna N 6-AN Adapter 2, 2, Aluminum, Aluminum Zinc Viton 62-AN Adapter 2, Aluminum* Buna N 66-AN Tank Truck Adapter 2 Aluminum* Buna N 66-SFN Adapter 4 Aluminum* Viton 662-A Adapter 2, 2, Aluminum* Viton 662-A Adapter 2, 2, Aluminum* Teflon 66-AN Adapter 2, 2, Aluminum* EPT 664-AN Adapter 2, 2, Stainless Steel* Buna N 67-AN Adapter 2, 2, Stainless Steel* Viton 672-AN Adapter 2, 2, Stainless Steel* Teflon 67-AN Adapter 2, 2, Stainless Steel* 0# Flange Teflon 67-ANF Adapter 2, 2 Stainless Steel* EPT 674-AN Adapter 2, 2, Stainless Steel* 0# Flange EPT 674-ANF Coupler 2, 2, Aluminum, Acetal Buna N 7-D Elbow Swivel Coupler 2 Aluminum, Acetal Buna N 7-ES Gravity Coupler 2, Aluminum, Acetal Buna N 7-GC Coupler 2, 2 Aluminum, Acetal Viton 72-D Coupler 4 Aluminum, Acetal Viton 72-DP Elbow Swivel Coupler 2 Aluminum, Acetal Viton 72-ES Coupler 2, 2, Aluminum* Buna N 76-D Coupler 2, 2, Aluminum* Viton 762-D Coupler 2, 2, Aluminum* EPT 764-D Coupler 2, 2, Aluminum* Teflon & Chemraz 76-D Coupler 2, 2, Stainless Steel* Buna N 77-D Coupler 2, 2, Stainless Steel* Viton 772-D Coupler 2, 2, Stainless Steel* EPT 774-D Coupler 2, 2, Stainless Steel* Teflon & Chemraz 77-D *Stainless Steel Corrosion Resistance is comparable to 04 Stainless Steel. D2000 TM Series Size Product (In.) Construction Seals No. Coupler 2, 2 Stainless Steel* Buna N 227-D Coupler 2, 2 Stainless Steel* Viton 2272-D Coupler 2, 2 Stainless Steel* EPT 2274-D Coupler 2, 2 Stainless Steel* Teflon & Chemraz 227-D *Stainless Steel Corrosion Resistance is comparable to 04 Stainless Steel. Kamvalok is a registered trademark and D2000 is a trademark of Civacon, Viton and Teflon are registered trademarks of the DuPont Co. and Chemraz is a registered trademark of Greene Tweed. 0

131 QUICK DISCONNECTS Dry Disconnect Hose Coupling Assembly Style 20 Couplers & 2 COUPLERS 2 & COUPLERS Pressure Data Maximum working pressure: 2 size 20 psi 2 size 20 psi 22 size 0 psi 2 size 20 psi WARNING: FOR ONE TIME FIELD TEST ONLY, the Maximum Joint Working Pressure may be increased to 2 times the figures shown. Vacuum: Tested to 28 vacuum in all positions without leakage. Miscellaneous test data: Bending Moments (coupled assembly): Maximum 200 ft/lbs at the swivel. Temperature: The Dry Link adapter/coupler assembly has an operating temperature range of -20 F to 20 F (-29 C to 0 C), using Viton or EPDM seals and 20 F to 20 F (-7 C to 0 C) using Teflon seals. Materials: Wetted Metal s: All 6 Stainless Steel. Seals: Choice of Viton, EPDM or Teflon ( and 2 available only with Teflon seals). Style 260 Adapters & 2 ADAPTERS 2 & ADAPTERS Viton and Teflon are registered trademarks of the DuPont Co. and Dry Link is a trademark of Victaulic.

132 QUICK DISCONNECTS SureStop Dry Disconnect Hose Coupling Dual Ball Valve Design puts the squeeze on leakage while providing greater flow. 2 Restricted Unrestricted full-flow Ball valves are an excellent method for controlling fluid flow. They are considerably more efficient than stopper-style valves which can restrict flow around the central poppet or piston. SureStop uses a modified ball valve design on each side of the hose coupling. When the coupling is engaged, the valves interact with each other to squeeze back all trace fluids. This prevents fluid entrapment, as well as leakage when the coupling is disengaged. Unique Valve Lever Interlock assures safe, consistent operation. It s easy to make reliable connections with SureStop. A simple one-eighth twist engages the two halves and creates a seal. You then use the levers to open the valves, one at a time. The first secures the seal; the second then permits chemical flow with minimal restriction. The coupling remains locked until both ball valves are fully closed, permitting disengagement. Low profile, easy-grip handles are coded by color and symbol for positive identification. Modified ball valve design effectively rejects trace fluids less than 2 ml fluid loss per disconnect Rugged, chemical resistant materials Engineered materials handle the toughest applications. SureStop is made to stand up to the harshest chemicals and environments. It is precision-molded of glass reinforced, corrosion-resistant polypropylene. Teflon seats and fluorocarbon seals provide for smooth operation while maintaining a secure, leak-proof contact. Lightweight, compact and easy to use, SureStop helps keep the costs of handling hazardous fluids and chemicals in line. Applications* Pesticides Fertilizers Chemicals Diesel Fuel Motor Oil Sludge/Slurry Waste Oil Paints Ink Molasses *Meets or exceeds California Department of Food & Agriculture Dry *Break Specifications (HS-7, Section V, Item 7.a.) of not more *than 2 ml of drippage per disconnect. CAUTION: Do not use with fluids that have a low flash point, static discharge could result in fire or explosion. Specifications: Operation: Modified dual ball valve design. Construction: Glass-filled polypropylene Teflon seats, fluorocarbon O-rings. Maximum operating pressure: 00 psi 70 F 7 psi 0 F. Size Inlet Opening Pressure (In.) NPT (In.) Drop No. negligible, full port DB restricted, port DB200 Low profile, easy and safe to use, disengagement can only take place after both ball valves are fully closed. SureStop is a trademark of Sotera Systems, Tuthill Corp. Teflon is a registered trademark of the DuPont Co. 2

133 QUICK DISCONNECTS The Smartlok System Verify Hose-Manifold Match A signature tag providing a unique serial number is attached to the hose coupling. An antenna, attached to the manifold adapter, communicates via EMF with a coupling s signature tag. Smartlok is a trademark of Civacon.

134 QUICK DISCONNECTS Hansen Quick Connect Couplings One-Way Couplings Auto-Flo Series Plug Recognition Auto-Flo 2 Socket Socket Interchanges with ARO, Truflate and Industrial Interchange plugs. 4 Size Plug 20 ARO type slightly longer nose. Very short nose Truflate short nose type. Series Auto-Flo 2 Sockets are compatible with Industrial Interchange, ARO and Truflate Plugs Male End Connections Male End Connections (In.) Socket Brass 4 MPTN 2AS-2MMMN. 4 MBSP 2AS-2MBSTT 8 MPTN 2AS-7MMMN. 8 MBSP 2AS-7MBSTT Plug Interchange with Industrial Interchange, ARO and Truflate plugs. Auto-Flo 24 Socket Socket Industrial interchange Hansen type. 4 Size Plug Female End Connections Female End Connections (In.) Socket Brass Plug Interchange with Industrial Interchange, ARO and Truflate plugs. Built to interchange with CEJN 20 Series and Rectus 2 Series designed to provide the highest flow of any of the 4 Series Auto-Flo sockets. enlarged nose. 4 FPTN 2AS-2FMM. 4 FBSP 2AS-2FBST 8 FPTN 2AS-7FMM. 8 FBSP 2AS-7FBST Hose Stem End Connections Socket Plug Interchange with Industrial Interchange, ARO and Truflate plugs. Hose Stem End Connections (In.) Brass 6 4 HS 2AS-2HT 6 HS 2AS-HT 6 8 HS 2AS-7HT Push-On Hose Stem End Connections Socket Plug Interchange with Industrial Interchange, ARO and Truflate plugs. Push-On Hose Stem Connections (In.) Brass 4 HS 2AS-2HP 8 HS 2AS-7HP Auto-Flo is a trademark of Hansen Coupling Division, Tuthill Corp. 4

135 QUICK DISCONNECTS One-Way Couplings continued Series Auto-Flo 24 Male End Connections Series 000, 400 and 00 Socket Plug Male End Connections (In.) Brass 4 MPTN 24AS-2M-GM 4 MBSP 24AS-2MBST 8 MBSP 24AS-7MBST 2 MBSP 24AS-0MBST Female End Connections Socket Male End Connections (In.) Brass 4 MPTN 24AP-2M-GM 4 MBSP 24AP-2MBST 8 MBSP 24AP-7MBST 2 MBSP 24AP-0MBST Plug Ball lock Quick-Connective Couplings are used for compressed air, gases and liquids. Body sizes are 4, 8 and 2. Series 000, 4 Nominal Male End Connections Socket Operating Pressure Series psi Bar 000 2, , ,00 6 Note: 400 Series Operating Pressure Automotive Plug is 0 psi. Plug Female End Connections (In.) Brass 4 FPTP 24AS-2F-G. 4 FBSP 24AS-2FBS 8 FBSP 24AS-7FBS 2 FBSP 24AS-0FBS Hose Stem End Connections Hose Stem End Connections (In.) Socket Steel 8 4 HS 24AS-2H 6 HS 24AS-H 8 8 HS 24AS-7H 8 2 HS 24AS-0H Female End Connections (In.) Brass 4 FPTP 24AP-2F-G. 4 FBSP 24AP-2FBS 8 FBSP 24AP-7FBS 2 FBSP 24AP-0FBS Plug Hose Stem End Connections (In.) Steel 8 4 HS 24AP-2H 6 HS 24AP-H 8 8 HS 24AP-7H 8 2 HS 24AP-0H Sockets with Steel Sleeve Male End Connections (In.) Brass 8 MPT MPT MPT 00-4 * MT* *8 8 8MT* Stainless 4 MPT LL-00 *4 Male Flare Female End Connections Sockets with Steel Sleeve Socket Male End Connections (In.) Steel 4 MPT 0 4 MPT 0G 8 MPT 2 8 MPT 2G 8 MPT 4 8 MPT 4G * MT* 0-4 Brass 4 MPT B-0 Stainless 4 MPT LL-0 *4 Male Flare Steel Plug with Bleeder Ball Check reduces hose whip when disconnecting. Plug Any plug and socket from the same series, regardless of end connection, fit together to make a coupling assembly. Female End Connections (In.) Brass 8 FPT FPT FPT 200 Stainless 4 FPT LL-000 *4 Male Flare Female End Connections (In.) Steel 4 FPT 4 FPT G 8 FPT 8 FPT Brass 4 FPT B Stainless 4 FPT LL- Steel Plug with Bleeder Ball Check reduces hose whip when disconnecting.

136 QUICK DISCONNECTS One-Way Couplings continued Series 000, 4 Nominal continued Hose Stem End Connections Sockets with Steel Sleeve Socket Plug Series 400, 8 Nominal Female End Connections Socket Plug Hose Stem End Connections (In.) 600P 700P 6P 7P Brass 8 4 HS *600P * 8 4 HS *600P * 8 8 HS *700P * 8 8 HS *700P * 6 HS *800P * *4 Male Flare. Intended for low-pressure push-on style hoses. Hose Stem End Connections (In.) Steel 8 4 HS HS 6G 8 4 HS 6P * 8 4 HS 6PG 8 8 HS HS 7G 8 8 HS 7P 8 8 HS 7PG 6 HS 8 Brass 8 8 HS B-7 *4 Male Flare. Steel Plug with Bleeder Ball Check reduces hose whip when disconnecting. Intended for low-pressure push-on style hoses. Female End Connections (In.) Brass 8 FPT 400-A 4 FPT 400-A 8 FPT 420-A 2 FPT 440-A Female End Connections (In.) Steel 4 FPT 4 4 FPT 4G 8 FPT 4 8 FPT 4G 2 FPT 4 Brass 8 FPT B-4 Steel Plug with Bleeder Check Valve reduces hose whip when disconnecting. Plug Female End Connections (In.) Steel 4 FPT AP-2F 8 FPT AP-7F Hose Clamp End Connections Sockets with Steel Sleeve Socket Plug Series 00, 2 Nominal Female End Connections Socket Plug Hose Clamp Hose Clamp I.D. O.D. (In.) (In.) Brass SA SA 2 -SB 222 -SB SB 888 -SB SC 888 -SC7 6 -SC SD 888 -SD7 6 -SD SD I.D. O.D. (In.) (In.) Steel PA PA 2 -PB 222 -PB PB 888 -PB7 6 -PB PB PC 888 -PC7 6 -PC PD 888 -PD7 6 -PD PD 6 -PD PD Female End Connections (In.) Brass 4 FPT 00-A 8 FPT 00-A 2 FPT 20-A 4 FPT 40-A Female End Connections (In.) Steel 4 FPT -A 8 FPT 8 FPT G 2 FPT 2 FPT G 4 FPT 7 Steel Plug with Bleeder Check Valve reduces hose whip when disconnecting. Any plug and socket from the same series, regardless of end connection, fit together to make a coupling assembly. 6

137 QUICK DISCONNECTS One-Way Couplings continued Series 000, 4000, 000 and 6000 Series 000, 4 Nominal continued Female End Connections Socket Plug Pin-lock Quick-Connective Couplings designed for compressed air, gases and liquids. Body sizes are 4, 8, 2 and 4. Operating Pressure Size Series (In.) psi Bar , , , ,220 Features The original Hansen designed automatic coupling offered in nominal sizes of 4, 8, 2 and 4. Easy, automatic, push-to-connect design provides instantaneous connection and disconnection of lines, plus automatic shut-off of socket end of line. When connected, plug is free to swivel 60 eliminating any kinks in the hose. The plug interchange for the series is the Industrial Interchange. Female End Connections (In.) Brass 8 FPT FPT FPT 200 Hose Stem End Connections Socket Female End Connections (In.) Steel 4 FPT 4 FPT G 8 FPT 8 FPT Brass 4 FPT B Stainless 4 FPT LL- Steel Plug with Bleeder Ball Check reduces hose whip when disconnecting. Plug Series 000, 4 Nominal Male End Connections Male End Connections (In.) Brass 8 MPT MPT MPT 00-4 * MT* *8 8 8 MT* *4 Male Flare Socket Plug Male End Connections (In.) Steel 4 MPT 0 4 MPT 0G 8 MPT 2 8 MPT 2G 8 MPT 4 8 MPT 4G * MT* 0-4 Brass 4 MPT B-0 Stainless 4 MPT LL-0 *4 Male Flare Steel Plug with Bleeder Ball Check reduces hose whip when disconnecting. Hose Stem End Connections (In.) 600P 700P 6P 7P Brass 8 4 HS *600P * 8 4 HS *600P * 8 8 HS *700P * 8 8 HS *700P * 6 HS *800P * *4 Male Flare. Intended for low-pressure push-on style hoses. Hose Stem End Connections (In.) Steel 8 4 HS HS 6G 8 4 HS 6P 8 4 HS 6PG * 8 8 HS HS 7G 8 8 HS 7P 8 8 HS 7PG 6 HS 8 Brass 8 8 HS B-7 *4 Male Flare. Steel Plug with Bleeder Ball Check reduces hose whip when disconnecting. Intended for low-pressure push-on style hoses. Any plug and socket from the same series, regardless of end connection, fit together to make a coupling assembly. 7

138 QUICK DISCONNECTS One-Way Couplings continued Series 000, 4 Nominal continued Hose Clamp End Connections Socket Plug Series 000, 2 Nominal Female End Connections Socket Plug Hose Clamp I.D. O.D. (In.) (In.) Brass SA SA 2 -SB 222 -SB SB 888 -SB7 6 -SB SB SC 888 -SC7 6 -SC SD 888 -SD7 6 -SD SD 6 -SD SD Hose Clamp I.D. O.D. (In.) (In.) Steel PA PA 2 -PB 222 -PB PB 888 -PB7 6 -PB PB PC 888 -PC7 6 -PC PD 888 -PD7 6 -PD PD 6 -PD PD Female End Connections (In.) Brass 4 FPT 000-A 8 FPT 000-A 2 FPT 200-A 4 FPT 400-A Series 6000, 4 Nominal Female End Connections Socket Female End Connections (In.) Steel 4 FPT -A 8 FPT 8 FPT G 2 FPT 2 FPT G 4 FPT 7 Steel Plug with Bleeder Ball Check reduces hose whip when disconnecting. Plug Series 4000, 8 Nominal Female End Connections Socket Plug Female End Connections (In.) Brass 2 FPT FPT 6400 FPT 6600 Female End Connections (In.) Steel 2 FPT 6A 2 FPT 6GA 4 FPT 67A 4 FPT 67GA FPT 69A Female End Connections (In.) Brass 8 FPT 4000-A 4 FPT 4000-A 8 FPT 4200-A 2 FPT 4400-A Female End Connections (In.) Steel 4 FPT 4 4 FPT 4G 8 FPT 4 8 FPT 4G 2 FPT 4 Brass 8 FPT B-4 Steel Plug with Bleeder Ball Check reduces hose whip when disconnecting. Series P-0 Plastic Socket & Plug Socket Hose Stem End Connections (In.) Plastic 4 HS P4-0S-2H Steel Plug with Bleeder Ball Check reduces hose whip when disconnecting. Plug Male End Connections (In.) Plastic 4 MPT P4-0P-2M Any plug and socket from the same series, regardless of end connection, fit together to make a coupling assembly. 8

139 QUICK DISCONNECTS One-Way Couplings continued Series Free Angle NPT Male x NPT Male Description (In.) No. 4 NPT Male x 4 NPT Male FA2M-2M 8 NPT Male x 8 NPT Male FA7M-7M Steel Balls Shaft Steel Balls NPT Female x NPT Male Packing Packing Typical Schematic Description (In.) No. Main Body Cover Main Body 4 NPT Female x 4 NPT Male FA2F-2M 4 NPT Female x 8 NPT Male FA2F-7M 8 NPT Female x 8 NPT Male FA7F-7M Hansen Coupling introduces a new line of products to help alleviate Carpal Tunnel Syndrome and other stress-related injuries in the workplace. The product is the Free Angle Fitting which is designed to rotate 60 at up to a 4 angle. Design Features Unique design provides free 60 rotation with up to a 4 angle of rotation in any direction. Steel construction for maximum service life. Two rotating joints are protected with polyurethane dust covers. Many styles and sizes available for any application. Design Benefits Provides flexibility of tool position to help alleviate Carpal Tunnel Syndrome and back stress, resulting in fewer lost-time injuries. Helps minimize paint mutilation. Prevents kinking of the air supply hose. Application Assembly air lines in Automotive, Electronic, and other industries. Mechanical joints for robotics. Vibration isolation. Commercial and residential construction. Industrial Interchange Plug x NPT Male Description (In.) No. 4 Industrial Interchange Plug x 4 NPT Male FA2P-2M 8 Industrial Interchange Plug x 4 NPT Male FA7P-2M 8 Industrial Interchange Plug x 8 NPT Male FA7P-7M Hose Barb x NPT Male Description (In.) No. 4 Hose Barb x 4 NPT Male FA2H-2M 8 Hose Barb x 8 NPT Male FA7H-7M 9

140 QUICK DISCONNECTS One-Way Special Application Couplings Gas-Mate Coupling Female End Connections Socket, Plug, One-way shut-off Safety Couplings are designed for LP and natural gas applications where 8, 2, 4,, and 4 hose is used. Gas-Mate is a registered trademark of Hansen Coupling Division, Tuthill Corp. Female End Connections (In.) Brass 8 FPT FPT FPT FPT FPT GMS20FH Each Gas-Mate Socket uses one O-Ring. Female End Connections (In.) Brass 8 FPT FPT FPT FPT FPT GMP20F Series 4-HK ( 2 ) Female End Connections Socket Two-Way Couplings High Pressure Hydraulic Two-Way Shut-Off Plug Series 8-HK ( ) Female End Connections Socket Plug Connection (In.) Material 2 FPT Steel 4-HP-26 2 FBSP Steel 4-HP-26BS FT Steel 4-HP-0 2 FPT Brass B4-HP-26 2 FBSP Brass B4-HP-26BS 2 FPT SS 0 LL4-HP-26 2 FBSP SS 0 LL4-HP-26BS FT SS 0 LL4-HP-0 2 FPT SS 6 ML4-HP-26 2 FBSP SS 6 ML4-HP-26BS Series 6-HK ( 8 ) Female End Connections Socket Connection (In.) Material 4 FPT Steel 6-HP- 4 FBSP Steel 6-HP-BS 6 2 FT Steel 6-HP-2 4 FPT Brass B6-HP- 4 FBSP Brass B6-HP-BS Connection (In.) Material 2 FPT Steel 4-KP-26 2 FBSP Steel 4-KP-26BS FT Steel 4-KP-0 2 FPT Brass B4-KP-26 2 FBSP Brass B4-KP-26BS 2 FPT SS 0 LL4-KP-26 2 FBSP SS 0 LL4-KP-26BS FT SS 0 LL4-KP-0 2 FPT SS 6 ML4-KP-26 2 FBSP SS 6 ML4-KP-26BS Plug Connection (In.) Material 4 FPT Steel 6-KP- 4 FBSP Steel 6-KP-BS 6 2 FT Steel 6-KP-2 4 FPT Brass B6-KP- 4 FBSP Brass B6-KP-BS Connection (In.) Material FPT Steel 8-HP-6 FBSP Steel 8-HP-6BS 6 2 FT Steel 8-HP-6 FPT Brass B8-HP-6 FBSP Brass B8-HP-6BS FPT SS 0 LL8-HP-6 FBSP SS 0 LL8-HP-6BS 6 2 FT SS 0 LL8-HP-6 FPT SS 6 ML8-HP-6 FBSP SS 6 ML8-HP-6BS Connection (In.) Material FPT Steel 8-KP-6 FBSP Steel 8-KP-6BS 6 2 FT Steel 8-KP-6 FPT Brass B8-KP-6 FBSP Brass B8-KP-6BS FPT SS 0 LL8-KP-6 FBSP SS 0 LL8-KP-6BS 6 2 FT SS 0 LL8-KP-6 FPT SS 6 ML8-KP-6 FBSP SS 6 ML8-KP-6BS Note: The standard valve assemblies in the Series -HK through 8-HK Sockets and Plugs are staked; and, therefore seals are non-replaceable without replacing the valve assembly. Series -HK to 8-HK Steam Coupling The Hansen Steam Coupling is designed with an extra-wide flange on the sleeve for gripping. The coupling with the special sleeve allows the coupling to be operated while the user wears heavy gloves for protection. A -92 seal is the standard seal in the coupling for steam applications (00 psi saturated steam 8 F). Female End Connections Socket Plug 4 FPT SS 0 LL6-HP- 4 FBSP SS 0 LL6-HP-BS 6 2 FT SS 0 LL6-HP-2 4 FPT SS 6 ML6-HP- 4 FBSP SS 6 ML6-HP-BS 4 FPT SS 0 LL6-KP- 4 FBSP SS 0 LL6-KP-BS 6 2 FT SS 0 LL6-KP-2 4 FPT SS 6 ML6-KP- 4 FBSP SS 6 ML6-KP-BS Connection (In.) Material 8 FPT Brass B--H2Y Connection (In.) Material 8 FPT Brass BK

141 QUICK DISCONNECTS Two-Way Couplings continued Series IA Series FF Flat Face SOCKET BODY SLEEVE PLUG BODY SOCKET BODY SLEEVE VALVE ASSEMBLY PLUG BODY The Hansen Series IA conforms to the dimensional requirements of the ISO Standard 724-I Series A. Pressure Ratings Series psi Bar 2-IA 4,600 -IA, IA, IA 4, IA, Meets dimensional and performance standards of HTMA* and NFPA. Series FF style double-shutoff hydraulic couplings are intended for use on medium pressure hydraulic systems up to 62 psi operating pressures. Combines dual flush-face valving, push-to-connect operation, minimum fluid loss upon disconnection, low air inclusion and sleeve lock. Primary applications are with hydraulic tools where cleaner automatic connections are needed and in machine tool line connections where minimum fluid spillage is required. * Hydraulic Tool Manufacturing Association National Fluid Power Association Female End Connections Pressure Ratings Socket Plug Series psi Bar 6FF,62 20 Body Size Connection (In.) (In.) Body Size Connection (In.) (In.) Female End Connections Socket Plug FPT 2-I-6 4 FBSP 2-I-6BS 8 FPT -I-2 8 FBSP -I-2BS 2 FPT 4-I-26 2 FBSP 4-I-26BS 4 FPT 6-I- 4 FBSP 6-I-BS 2 FPT 8-I-6 2 FBSP 8-I-6BS FPT 2-A-6 4 FBSP 2-A-6BS 8 FPT -A-2 8 FBSP -A-2BS 2 FPT 4-A-26 2 FBSP 4-A-26BS 4 FPT 6-A- 4 FBSP 6-A-BS 2 FPT 8-A-6 2 FBSP 8-A-6BS Female End Connections (In.) Steel 8 FPTP 6-FFS-8FA 8 FBSP 6-FFS-8FBSA 2 FPTP 6-FFS-0FA 2 FBSP 6-FFS-0FBSA Female End Connections (In.) Steel 8 FPTP 6-FFP-8FA 8 FBSP 6-FFP-8FBSA 2 FPTP 6-FFP-0FA 2 FBSP 6-FFP-0FBSA Agricultural Hydraulic Quick Connect Fittings Female End Connections FPT Ball Valve Coupler FPT Ball Valve Plug Agricultural series couplers are used on construction equipment, farm implements and most other mobile equipment. Interchangeable with Pioneer 4000 Series and Safeway Agricultural Series. Operating pressure: 200 psi Socket Body Size NPT Thread (In.) (In.) Plug Body Size NPT Thread (In.) (In.)

142 QUICK DISCONNECTS Two-Way Couplings continued Series 96 Series UP Ultra Pressure 0,000 psi SOCKET BODY SLEEVE PLUG BODY Hansen Series 96 is a heavy-duty wing nut coupling which is designed for use in hydraulic lines where dry break and minimum air inclusion is required. The couplings are ideal for hydraulic dump trucks, oil field equipment, and spreading equipment. Features Non-spill double shut-off with minimum air inclusion. Connect/disconnect under pressure. Corrosion resistant brass body. Interchangeable with other manufacturers. Pressure Ratings Size (In.) psi Bar 4, , ,70 90 SOCKET BODY SLEEVE PLUG BODY Hansen Series UP (Ultra Pressure) is designed for applications where hydraulic fluid is being used at pressures up to 0,000 psi (700 BAR). The coupling has a ball lock mechanism that replaces the threaded connections typically used in high pressure hydraulics. Features Sleeve type connection with sleeve lock device. Slim profile compared to threaded coupling designs. Body materials made of high strength steel for durability. Pressure Ratings Series psi Bar UP 0, Male End Connections Male End Connections (In.) Socket Steel 4 MPT UP0S-2M 8 MPT UP0S-7M Plug Male End Connections (In.) Steel 4 MPT UP0P-2M 8 MPT UP0P-7M Female End Connections Female End Connections Socket Plug Socket Plug Body Size Connection (In.) (In.) Body Size Connection (In.) (In.) Female End Connections (In.) Steel 4 FPT UP0S-2F 8 FPT UP0S-7F Female End Connections (In.) Steel 4 FPT UP0P-2F 8 FPT UP0P-7F 4 4 FPT 96-S 2 2 FPT 96-S6 4 4 FPT 96-S4 4 4 FPT 96-P 2 2 FPT 96-P6 4 4 FPT 96-P4 Any plug and socket from the same series, regardless of end connection, fit together to make a coupling assembly. 42

143 QUICK DISCONNECTS Two-Way Couplings continued Series DB Pressure Ratings Size (In.) psi Bar 2 00 SOCKET END PLUG END Spillage/Inclusion Body Spillage Air Inclusion Size Max. Per Max. Per (In.) Disconnect Connect 2.02 ml.02 ml Female End Connections Socket Plug SOCKET BODY SLEEVE PLUG BODY Hansen Series DB is designed for fluid handling where no spillage is required. The coupling is made of 6 Stainless Steel which allows for use in chemical processing, pharmaceutical and food processing industries. Features Push-to-connect flush face design. Excellent flow, exceeding ISO B design couplings. All materials 6 Stainless Steel with Viton seals standard. Optional end connections are available. Female End Connections (In.) Steel 2 FBSP 4DBS-0FBS 2 FPTP 4DBS-0FBS Female End Connections (In.) Steel 2 FBSP 4DBP-0FBS 2 FPTP 4DBP-0FBS Straight Thru Couplings Flo-Temp Series Injection Molding Couplings Valved Non-Valved Hansen s Flo-Temp Series provides maximum flow required to cool injection molds. The product is available valved or non-valved depending on your application for use with hot oil, water-glycol, and hot water. Features Sockets have a brass construction with 02 stainless steel valve springs and 440 stainless steel locking balls. Plugs are designed short so that they can be easily recessed below the mold surface to avoid damage when the mold is being changed or stored. Valved models for automatic shut-off when line is disconnected. Non-valved straight-through models for maximum flow requirements and automatic shut-off is not a factor. Flo-Temp is a registered trademark of Hansen Coupling Division, Tuthill Corp. Any plug and socket from the same series, regardless of end connection, fit together to make a coupling assembly. 4

144 Flo-Temp Series continued QUICK DISCONNECTS Straight Thru Couplings continued Male Plug Mounting Information A C B H Flush Mounted Plug Externally Mounted Plug Dimensions (In.) NPT Hex Size (In.) (In.) A B C H Brass FTP FTP FTP FTP FTP FTP FTP FTP-6 Flo-Temp Series 200, 4 Nominal Sockets and Plugs Socket Barb Style End Connections Plug Male End Connections Hose I.D. Barb Stem (In.) Style Style Brass 4 Standard Straight FTS valved Standard Straight FTS-204V 4 Push-On* Straight FTS-204HP 4 valved Push-On* Straight FTS-204VHP 6 Standard Straight FTS-20 6 valved Standard Straight FTS-20V 8 Standard Straight FTS valved Standard Straight FTS-206V 8 Push-On* Straight FTS-206HP 8 valved Push-On* Straight FTS-206VHP 4 Standard 90 FTS-24 4 valved Standard 90 FTS-24V 4 Push-On* 90 FTS-24HP 4 valved Push-On* 90 FTS-24VHP 6 Standard 90 FTS-2 6 valved Standard 90 FTS-2V 8 Standard 90 FTS-26 8 valved Standard 90 FTS-26V 8 Push-On* 90 FTS-26HP 8 valved Push-On* 90 FTS-26VHP 4 Standard 4 FTS valved Standard 4 FTS-224V 4 Push-On* 4 FTS-224HP 4 valved Push-On* 4 FTS-224VHP 6 Standard 4 FTS-22 6 valved Standard 4 FTS-22V 8 Standard 4 FTS valved Standard 4 FTS-226V 8 Push-On* 4 FTS-226HP 8 valved Push-On* 4 FTS-226VHP *Push-On style hose barbs are self-locking and do not *require clamps. Sockets Plugs Thread Size Flow Diameter (In.) (In.) Brass 8 MPT 4 FTP-2 8 MBSP 4 FTP-2BST 4 MPT 4 FTP-22 4 MBSP 4 FTP-22BST 8 MPT 4 FTP-2 Plug Female End Connections Thread Size Flow Diameter (In.) (In.) Steel 8 FPT 4 FTP-2-F 8 FBSP 4 FTP-2-FBS 4 FPT 4 FTP-22-F 4 FBSP 4 FTP-22-FBS 8 FPT 4 FTP-2-F Mold Mate Injection Molding Flo-Temp is a registered trademark of Hansen Coupling Division, Tuthill Corp. 44

145 QUICK DISCONNECTS Straight Thru Couplings continued Flo-Temp Series 00, 8 Nominal Sockets and Plugs Socket Barb Style End Connections Plug Male End Connections Hose I.D. Barb Stem (In.) Style Style Brass 8 Standard Straight FTS-06 8 valved Standard Straight FTS-06V 8 Push-On* Straight FTS-06HP 8 valved Push-On* Straight FTS-06VHP 2 Standard Straight FTS-08 2 valved Standard Straight FTS-08V 2 Push-On* Straight FTS-08HP 2 valved Push-On* Straight FTS-08VHP 8 Standard 90 FTS-6 8 valved Standard 90 FTS-6V 8 Push-On* 90 FTS-6HP 8 valved Push-On* 90 FTS-6VHP 2 Standard 90 FTS-8 2 valved Standard 90 FTS-8V 2 Push-On* 90 FTS-8HP 2 valved Push-On* 90 FTS-8VHP Sockets Plugs Thread Size Flow Diameter (In.) (In.) Brass 4 MPT 8 FTP-2 4 MBSP 8 FTP-2BST 8 MPT 8 FTP- 2 MPT 8 FTP-4 Plug Female End Connections Thread Size Flow Diameter (In.) (In.) Steel 4 FPT 8 FTP-2-F 4 FBSP 8 FTP-2-FBS 8 FPT 8 FTP--F 8 FBSP 8 FTP--FBS 2 FPT 8 FTP-4-F 8 Standard 4 FTS-26 8 valved Standard 4 FTS-26V 8 Push-On* 4 FTS-26HP 8 valved Push-On* 4 FTS-26VHP 2 Standard 4 FTS-28 2 valved Standard 4 FTS-28V 2 Push-On* 4 FTS-28HP 2 valved Push-On* 4 FTS-28VHP *Push-On style hose barbs are self-locking and do not *require clamps. Flo-Temp Series 00, 2 Nominal Sockets and Plugs Socket Barb Style End Connections Plug Male End Connections Hose I.D. Barb Stem (In.) Style Style Brass 2 Standard Straight FTS-04 2 valved Standard Straight FTS-04V 2 Push-On* Straight FTS-04HP 2 valved Push-On* Straight FTS-04VHP 4 Standard Straight FTS-06 4 valved Standard Straight FTS-06V 4 Push-On* Straight FTS-06HP 4 valved Push-On* Straight FTS-06VHP *Push-On style hose barbs are self-locking and do not *require clamps. Socket Plugs Thread Size Flow Diameter (In.) (In.) Brass 2 MPT 8 FTP-4 4 MPT 8 FTP-6 Plug Female End Connections Thread Size Flow Diameter (In.) (In.) Steel 2 FPT 8 FTP-4-F 4 FPT 8 FTP-6-F Flo-Temp is a registered trademark of Hansen Coupling Division, Tuthill Corp. 4

146 Series ST without Shut-Off Valves QUICK DISCONNECTS Straight Thru Couplings continued Power Wash and Agricultural Applications Each Series ST Socket is equipped with a Buna N O-ring, and other compounds are available to handle a wide variety of liquids and gases. Features Smooth bore permits free flow of liquid or gas. Pressure Rating Service with Steel Plug with Brass Plug Stainless Steel Series psi Bar psi Bar psi Bar -ST 2, ,00 7 4, ST,00 80, , ST, ,700 86, ST 2, ,200 2, ST,700 7,700 7, ST 2,000 8,200 8, ST 2,700 86, , ST 2,200 2, , ST 2,200 2,400 97, ST,00 0, Male End Connections Thread Size Stainless (In.) Series Brass Steel 8 MPT -ST -S0 LL-S0 4 MPT 2-ST 2-S 8 MPT -ST -S20 LL-S20 2 MPT 4-ST 4-S2 4 MPT 6-ST 6-S0 LL6-S0 MPT 8-ST 8-S For optional Sleeve Lock Device add -SL to Socket Plug Thread Size Stainless (In.) Series Steel Brass Steel 8 MPT -ST -T0 B-T0 LL-T0 4 MPT -ST -T B-T 4 MPT 2-ST.2-T B2-T LL2-T 8 MPT -ST -T20 B-T20 LL-T20 2 MPT 4-ST 4-T2 B4-T2 LL4-T2 4 MPT 6-ST 6-T0 B6-T0 LL6-T0 MPT 8-ST 8-T B8-T LL8-T 4 MPT 0-ST 0-T40 B0-T40 LL0-T40 2 MPT 2-ST 2-T4 B2-T4 2 MPT 6-ST 6-T0 B6-T0 LL6-T0 2 2 MPT 20-ST 20-T B20-T Female End Connections Thread Size Stainless (In.) Series Brass Steel 8 FPT -ST -S LL-S 4 FPT 2-ST 2-S6 LL2-S6 8 FPT -ST -S2 LL-S2 2 FPT 4-ST 4-S26 LL4-S26 4 FPT 6-ST 6-S LL6-S FPT 8-ST 8-S6 LL8-S6 4 FPT 0-ST 0-S4* LL0-S4 2 FPT 2-ST 2-S46* LL2-S46 2 FPT 6-ST 6-S* LL6-S 2 2 FPT 20-ST 20-S6* For optional Sleeve Lock Device add -SL to * with Steel Sleeve. Socket Plug Thread Size Stainless (In.) Series Steel Brass Steel 8 FPT -ST -T B-T LL-T 4 FPT 2-ST.2-T6 B2-T6 LL2-T6 8 FPT -ST -T2 B-T2 LL-T2 2 FPT 4-ST 4-T26 B4-T26 LL4-T26 4 FPT 6-ST 6-T B6-T LL6-T FPT 8-ST 8-T6 B8-T6 LL8-T6 4 FPT 0-ST 0-T4 B0-T4 LL0-T4 2 FPT 2-ST 2-T46 B2-T46 LL2-T46 2 FPT 6-ST 6-T B6-T 2 2 FPT 20-ST 20-T6 B20-T6 Any plug and socket from the same series, regardless of end connection, fit together to make a coupling assembly. 46

147 QUICK DISCONNECTS Straight Thru Couplings continued Series ST without Shut-Off Valves continued Hose Stem End Connections Hose Socket Size Stainless (In.) Series Brass Steel 6 HS -ST *-S2* *LL-S2* 4 HS -ST *-S7* *LL-S7* 4 HS 2-ST 2-S7 8 HS -ST -S22 LL-S22 2 HS 4-ST 4-S27 4 HS 6-ST 6-S2 LL6-S2 HS 8-ST 8-S7 LL8-S7 For optional Sleeve Lock Device add -SL to *May differ from drawing and is made for hex stock. Plug Hose Size Stainless (In.) Series Steel Brass Steel 6 HS -ST B-T2 LL-T2 4 HS -ST B-T7 LL-T7 4 HS 2-ST 2-T7 B2-T7 8 HS -ST -T22 B-T22 LL-T22 2 HS 4-ST 4-T27 B4-T27 4 HS 6-ST 6-T2 B6-T2 LL6-T2 HS 8-ST 8-T7 B8-T7 Dust Caps Plastic Socket Dust Cap Socket and Plug Plastic Dust Caps Plastic Plug Dust Cap Plastic Dust Caps for One-Way Shut-Off Couplings One-Way Socket Plug Series Dust Cap Dust Cap 000 P-SDC--HK 4000 P-SDC-2-HK 000 P-PDC-2-HK 6000 P-PDC--HK 000 P-SDC--HK 00 P-SDC--HK P-PDC--HK 400 P-SDC-2-HK 600 P-SDC--HK P-PDC--HK 700 P-SDC--HK P-PDC--HK 2-RL P-SDC--HK P-PDC--HK -RL P-SDC-2-HK P-PDC-2-HK Plastic Dust Caps for Gas-Mate Couplings Dust Caps are available where protection is necessary against excessive flying grit or dust. The Socket Dust Cap is easily applied by pulling back the sleeve of the Socket and inserting the Dust Cap. The Plug Dust Cap covers the entire machined surface of the Plug. It is applied and held in place by friction on the locking portion of the Plug. Metal Dust Caps are supplied with chain and attachment ring. Plastic Dust Caps have integral plastic strap and attachment loop. Plastic Dust Caps for Two-Way Shut-Off Couplings Two-Way Socket Plug Series Dust Cap Dust Cap -HK P-SDC--HK P-PDC--HK 2-HK P-SDC-2-HK P-PDC-2-HK -HK P-SDC--HK P-PDC--HK 4-HK P-SDC-4-HK P-PDC-4-HK 6-HK P-SDC-6-HK P-PDC-6-HK 8-HK P-SDC-8-HK P-PDC-8-HK 0-HK 2-HK 20-HK 2-HKIG P-PDC-2-HK 2-HKIL P-PDC-2-HK 6FF P-SDC-6FF-. P-PDC-6FF-. Gas-Mate Series Socket Plug (In.) Dust Cap Dust Cap 4 P-SDC--HK P-PDC--HK 8 P-SDC-2-HK P-PDC-2-HK 2 P-SDC--HK P-PDC--HK 4 P-SDC-4-HK P-PDC-4-HK 2 P-SDC-6-HK P-PDC-6-HK Plastic Dust Caps for Straight Through Couplings Straight Through Socket Plug Series Dust Cap Dust Cap 2-ST P-SDC--HK -ST P-SDC-2-HK 6-ST P-SDC-4-HK P-PDC-4-HK 8-ST P-PDC-6-HK 0-ST P-PDC-8-HK 47

148 QUICK DISCONNECTS Spray Nozzles and Accessories for the Power Wash Industry Pressure Washer Gun Quick Connect QCMEG WashJet Spray Nozzles Makes Replacement Easy Male Plug (Brass) Size (In.) No. 4 M NPT B2-T 47 /4 Discharge Maximum pressure: 4000 psi Maximum flow: 2 gpm Maximum temperature: 00 F (49 C) Inlet: /8 NPT Outlet: /4 NPT Weight: 2.2 oz. Wand, Pipe Only Zinc Plated Steel /4 Male Thread, Both Ends Working pressure: 400 psi Burst pressure:,000 psi Length (In.) No Color-coded, quick connect QCMEG WashJet spray nozzles can be used to 4000 psi and fit Parker ST series, Hansen 2-S6 and equivalent couplings. The hardened stainless steel nozzles offer superior wear-resistance and have colored-coded nozzle guards that identify the spray angles available of 0,, 2 and 40. Bore Nos. Size (gpm) Female Socket Size (In.) No. 4 2-S6 Female Plug (Brass) Size (In.) No. 4 F NPT B2-T6 Quick-Change Swivel/ Quick Disconnect Screw-together connection; no wrenches; repairable/rebuildable; assembles easily; swivels easily; remove hoses fast and economically; no side pressure; no breakage. M22x. thread on connection with plug. Maximum temperature: 200 F (9 C) Maximum pressure: 4000 psi Size Swivel Screw (In.) Nut Plug 4 F NPT M NPT F NPT M NPT Power Washer Accessories 48

149 FAX: HYDRAULIC TECHNICAL DATA Hydraulic Coupling Identification There are five coupling systems generally used for hydraulic connections today. They are identified geographically or by country as: North American British French German Japanese This section lists the origin and coupling style found in each country. Brief descriptions and dimensional data follows each coupling style. North American Thread Types Iron Pipe Thread Abbreviations N National F Fuels P Pipe S Straight Thread T Tapered Thread M Mechanical Joint NPTF This is a dryseal thread; the National pipe tapered thread for fuels. This is used for both male and female ends. The NPTF male will mate with the NPTF, NPSF, or NPSM female. The NPTF male has tapered threads and a 0 inverted seat. The NPTF female has tapered threads and no seat. The seal takes place by deformation of the threads. The NPSM female has straight threads and a 0 inverted seat. The seal takes place on the 0 seat. The NPTF connector is similar to, but not interchangeable with, the BSPT connector. The thread pitch is different in most sizes. Also, the thread angle is 60 instead of the angle found on BSPT threads. NPSF The National pipe straight thread for fuels. This is sometimes used for female ends and properly mates with the NPTF male end. However, the SAE recommends the NPTF thread in preference to the NPSF for female ends. NPSM National pipe straight thread for mechanical joint. This is used on the female swivel nut of iron pipe swivel adapters. The leak-resistant joint is not made by the sealing fit of threads, but by a tapered seat in the coupling end. NPT Pipe Thread Nominal No. Male Female Dash Size Threads Thread Thread Size (In.) Per Inch O.D. (In.) I.D. (In.)

150 FAX: HYDRAULIC TECHNICAL DATA Hydraulic Coupling Identification, North American continued *7 Flare (JIC) The Society of Automotive Engineers (SAE) specifies a 7 angle flare or seat be used with high pressure hydraulic tubing. These are commonly called JIC couplings. The JIC 7 flare male will mate with a JIC female only. The JIC male has straight threads and a 7 flare seat. The JIC female has straight threads and a 7 flare seat. The seal is made on the 7 flare seat. All sizes have the same threads as the SAE 4 flare except 6 and 2. Carefully measure the seat angle to differentiate. *Note: Some C, CE and Lock-On couplings may have *Note: dual machined seats (both 7 and 4 seats). 7 Flare (JIC) Nominal Male Female Dash Size Thread Thread Thread Size (In.) Size O.D. (In.) I.D. (In.) *SAE (4 Flare) A term usually applied to fittings having a 4 angle flare or seat. Soft copper tubing is generally used in such applications as it is easily flared to the 4 angle. These are for low pressure applications such as for fuel lines and refrigerant lines. The SAE 4 flare male will mate with an SAE 4 flare female only. The SAE male has straight threads and a 4 flare seat. The SAE female has straight threads and a 4 flare seat. The seal is made on the 4 flare seat. All sizes have the same threads as the SAE 4 flare except 6 and 2. Carefully measure the seat angle to differentiate. *Note: Some C, CE and Lock-On couplings may have *Note: dual machined seats (both 7 and 4 seats). Nominal Male Female Dash Size Thread Thread Thread Size (In.) Size O.D. (In.) I.D. (In.) SAE 4 Flare 0

151 FAX: HYDRAULIC TECHNICAL DATA Hydraulic Coupling Identification, North American continued O-Ring Boss The O-ring boss male will mate with an O-ring boss female only. The female is generally found on ports. The male has straight threads and an O-ring. The female has straight threads and a sealing face. The seal is made at the O-ring on the male and the sealing face on the female. SAE Straight Thread O-Ring Boss Nominal Male Female Dash Size Thread Thread Thread O-Ring Size (In.) Size O.D. (In.) I.D. (In.) Size O-Ring Flange SAE J8 The SAE Code 6 and Code 62 4-Bolt Split Flange is used worldwide, usually as a connection on pumps and motors. There are three exceptions.. The 0 size, which is common outside of North America, is not an SAE Standard size. 2. Caterpillar flanges, which are the same flange O.D. as SAE Code 62, have a thicker flange head ( C dimension in Table).. Poclain flanges, which are completely different from SAE flanges. SAE Code 6 and Code 62 Nominal Code 6 (FL) Code 62 (FLH) Caterpillar (FLC) Flange Flange Flange Flange Size O.D. A B C O.D. A B C O.D. A B C

152 FAX: HYDRAULIC TECHNICAL DATA Hydraulic Coupling Identification, North American continued O-Ring Face Seal (ORFS) J4 A seal is made when the O-ring in the male contacts the flat face on the female. Couplings are intended for hydraulic systems where elastomeric seals are acceptable to overcome leakage and leak resistance is crucial. The solid male O-ring face seal fitting will mate with a swivel female O-ring face seal fitting only. An O-ring rests in the O-ring groove in the male. O-Ring Face Seal Nominal Male Female O-Ring Dash Size Thread Thread Thread Size Size (In.) Size O.D. (In.) I.D. (In.) (SAE J20) Flareless Tube The flareless solid male will mate with a female flareless nut and compression sleeve only. The male has straight threads and a 24 seat. The female has straight threads and has a compression sleeve for a sealing surface. The seal is made between the compression sleeve and the 24 seat on the male, and between the compression sleeve and the tubing on the female. Flareless Tube Tube Nominal Male Female Dash Size Size Thread Thread Thread Size (In.) (In.) Size O.D. (In.) I.D. (In.) SAE Inverted Flare The SAE 4 inverted flare male will mate with an SAE 42 inverted flare female only. The male has straight threads and a 4 inverted flare. The female has straight threads and a 42 inverted flare. The seal is made on the 4 flare seat on the male and the 42 flare seat on the female. SAE Inverted Flare Nominal Male Female Dash Size Thread Thread Thread Size (In.) Size O.D. (In.) I.D. (In.)

153 FAX: HYDRAULIC TECHNICAL DATA Hydraulic Coupling Identification, North American continued Female Brazed-On Stems Braze-On Stems Dash Size Tubing O.D. B (In.) Grease Fittings Special Male Grease Fitting Special Female Grease Fitting Parker Triple Thread Flare Fittings Parker Triple Thread Flare Fittings Nominal Female Male Dash Size Thread Thread Thread Size (In.) Size I.D. (In.) O.D. (In.) Swivel Female (FZX) 0 o Thread I.D. Thread O.D. 0 o Solid Male (MZ) Press-Lok Connectors Press-Lok style connectors are found on mining equipment worldwide. The seal is made when the O-ring on the male contacts the inside surface of the female. The two connectors are held together with a staple. Press-Lok Connectors Nominal Dash Size Male Female Size (In.) I.D. (In.) O.D. (In.) Press-Lok is a trademark of The Gates Rubber Company.

154 FAX: HYDRAULIC TECHNICAL DATA Hydraulic Coupling Identification, Foreign Thread Types British It is a common misconception that all foreign threads are metric. This is not always the case. There are two common thread forms metric and Whitworth (BSP). The country of origin and the proper nomenclature for each is listed below. Identifying Foreign Couplings If you can identify the country of origin of the equipment you are working with, it is easy to identify the coupling style. Simply find the appropriate country in the following pages and locate the particular coupling in the table that follows. British Standard Pipe Parallel Popular couplings have British Standard Pipe (BSP) threads, also known as Whitworth threads. These can be parallel (BSPP) or tapered (BSPT), with a 0 inverted flare. Flanges are equivalent to SAE Code 6 or Code 62 (except 0*). Port connections are usually made with BSPP threads and a soft metal cutting ring for sealing. The BSPP (parallel) male will mate with a BSPP (parallel) female or a female port. The BSPP male has straight threads and a 0 seat. The BSPP female has straight threads and a 0 seat. The female port has straight threads and a spotface. The seal on the port is made with an O-ring or soft metal washer on the male. The BSPP (parallel) connector is similar to, but not interchangeable with, the NPSM connector. The thread pitch is different in most sizes, and the thread angle is instead of the 60 angle found on NPSM threads. *( 0 is a non-sae size flange) Male Female Nominal Parallel Parallel Dash Size Thread Thread Thread Size (In.) Size I.D. (In.) O.D. (In.) * 0* *( 0 is a non-sae size flange) British Standard Pipe Parallel (BSPP) British Standard Pipe Tapered The BSPT (tapered) male will mate with a BSPT (tapered) female, or a BSPP (parallel) female. The BSPT male has tapered threads. When mating with either the BSPT (tapered) female or the BSPP (parallel) female port, the seal is made on the threads. The BSPT connector is similar to, but not interchangeable with, the NPTF connector. The thread pitch is different in most cases, and the thread angle is instead of the 60 angle found on NPTF threads. British Standard Pipe Tapered (BSPT) Male Female Nominal Tapered Tapered Dash Size Thread Thread Thread Size (In.) Size I.D. (In.) O.D. (In.)

155 FAX: HYDRAULIC TECHNICAL DATA Hydraulic Coupling Identification, Foreign Thread Types continued French Popular couplings are French GAZ. These have a 24 seat and metric threads. These are similar to German DIN couplings, but the threads are different in some sizes. Although both are metric threads, the French use fine threads in all sizes and German DIN couplings use coarse threads in larger sizes. Most port connections are flange connections. French flanges are different from SAE they have a lip that protrudes from the flange face. These are called Poclain style flanges. GAZ 24 The French Metric (GAZ) male will mate with the female 24 cone or the female tube fitting. The male has a 24 seat and straight metric threads. The female has a 24 seat or a tubing sleeve and straight metric threads. When measuring the flare angle with the seat angle gauge, use the 2 gauge. (The seat angle gauge measures the angle from the connector centerline). French Metric (GAZ) Metric Male Female Tube Thread Thread Thread O.D. Size O.D. (mm) I.D. (mm) (mm) M20x M24x M0x M6x M4x M2x GAZ Poclain 24 Flange The Poclain (French GAZ) 24 high pressure flange is usually found on Poclain equipment. The male flange will mate with a female flange or a port. The seal is made on the 24 seat. Poclain (French GAZ) Nominal Size A B C D E F (In.) (In.) (In.) (In.) (In.) (In.) (In.)

156 FAX: HYDRAULIC TECHNICAL DATA Hydraulic Coupling Identification, Foreign Thread Types continued German DIN (Deutsche Industrial Norme) Popular couplings are German DIN (Deutsche Industrial Norme). A coupling referred to as metric, usually means a DIN coupling. Flanges are standard Code 6 or Code 62 (except 0)*. *( 0 is a non-sae size flange) DIN 24 Male and Mating Female DIN 24 Cone The DIN 24 cone male will mate with any of the three females shown. The male has a 24 seat, straight metric threads, and a recessed counterbore which matches the tube O.D. of the coupling used with it. The mating female is a 24 cone with O-ring, a metric tube fitting or a universal 24 or 60 cone. There is a light and heavy series DIN coupling. Proper identification is made by measuring both the thread size and the tube O.D. (The heavy series has a smaller tube O.D. than the light, but has a thicker wall section.) When measuring the flare angle with the seat angle gauge, use the 2 gauge. (The seat angle gauge measures the angle from the connector centerline.) Metric Male Female Tube O.D. Tube O.D. Thread Thread Thread Light Heavy Size O.D. (mm) I.D. (mm) Series (mm) Series (mm) M2x M4x M6x M8x M20x M22x M24x M26x M0x M6x M42x M4x M2x DIN 60 Male and Mating Female DIN 60 Cone The DIN 60 cone male will mate with the female universal 24 or 60 cone connector only. The male has a 60 seat and straight metric threads. The female has a 24 and 60 universal seat and straight metric threads. When measuring the flare angle with the seat angle gauge, use the 0 gauge. (The seat angle gauge measures the angle from the connector centerline). Metric Male Female Tube Thread Thread Thread O.D. Size O.D. (mm) I.D. (mm) (mm) M4x M6x M8x M22x M26x M0x M8x M4x M2x

157 FAX: HYDRAULIC TECHNICAL DATA Hydraulic Coupling Identification, Foreign Thread Types continued German DIN (Deutsche Industrial Norme) continued DIN 82 Couplings Type A & B (Parallel Threads) The male DIN 82 Type A & B couplings will mate with the female DIN coupling shown below. The male and female type A & B couplings have straight threads. Sheet refers to straight metric threads, and Sheet 2 refers to straight Whitworth threads. The seal occurs when the ring seal (Type A) or the face seal (Type B) mates with the face of the female port. There are two series of DIN 82 Type A & B couplings, the light (L) and the heavy (S) series. DIN 82 Couplings Type A & B (Parallel Threads) Male Male Female Female Metric Thread Whitworth Thread Metric Thread Whitworth Thread Parallel Parallel Parallel Parallel DIN 82 Type A & B DIN 82 Type A & B DIN 82 Type A & B DIN 82 Type A & B SERIES Sheet Sheet 2 Sheet Sheet 2 Tube Metric Thread Whitworth Thread Metric Thread Whitworth Thread O.D. Thread O.D. A B C Thread O.D. A B C Thread I.D. A B Thread I.D. A B mm Size (mm) (mm) (mm) (mm) Size (In.) (mm) (mm) (mm) Size (mm) (mm) (mm) Size (In.) (mm) (mm) L 6 0x x Light 8 2x x x x x x x x x x x x x x x x x x S 6 2x x Heavy 8 4x x x x x x x x x x x x x x x x x x

158 FAX: HYDRAULIC TECHNICAL DATA Hydraulic Coupling Identification, Foreign Thread Types continued German DIN (Deutsche Industrial Norme) continued DIN 82 Type C Sheets & 2 Metric and Whitworth Tapered Thread Connectors DIN 82 Type C Sheets & 2 Metric and Whitworth Tapered Thread Connectors The DIN 82 Type C couplings are available with either metric or Whitworth British thread. The male will mate only with the female as shown. The male and female couplings have tapered threads. Sheet refers to tapered metric threads, and Sheet 2 refers to tapered Whitworth threads. The seal takes place on the threads. There are three series of DIN 82 Type C couplings: extra light (LL), light (L) and heavy (S). Male DIN 82 Male DIN 82 Female DIN 82 Female DIN 82 Type C, Sheet Type C, Sheet 2 Type C, Sheet Type C, Sheet 2 SERIES Metric Tapered Threads Whitworth Tapered Threads Metric Tapered Threads Whitworth Tapered Threads Tube Metric Thread Whitworth Thread Metric Thread Whitworth Thread O.D. Thread A B O.D. Thread A B O.D. Thread I.D. A Thread I.D. A (mm) Size (mm) (mm) (mm) Size (In.) (mm) (In.) Size (mm) (mm) Size (In.) (mm) LL 4 8x x Extra 8x x Light 6 0x x x x L 6 0x x Light 8 2x x x x x x x x x x S 6 2x x Heavy 8 4x x x x x x x x x x Metric Standpipe Assembly A metric standpipe assembly is comprised of three components attached to a male fitting. The components are: a Standpipe, Bite Sleeve and Metric Nut. The nut is placed over the Standpipe, followed by the Bite Sleeve (see illustration below). For DIN light assemblies, a DIN light metric nut is used. For DIN heavy assemblies, a DIN heavy metric nut is used. The Bite Sleeve and Standpipe are selected on the basis of tube O.D. required. Metric Standpipe Assembly Metric Standpipe Bite Sleeve Metric Nut Thread DIN Tube O.D. DIN Tube O.D. (mm) (mm) Light Heavy 6 6 M2x. 8 8 M4x. M6x. 0 0 M6x. M8x. 2 2 M8x. M20x. M22x. 6 6 M24x. 8 8 M26x M0x M0x M6x M6x M42x2. M4x M2x M2x2. 8

159 FAX: HYDRAULIC TECHNICAL DATA Hydraulic Coupling Identification, Foreign Thread Types continued Japanese There are two popular coupling styles in Japan.. All Komatsu equipment uses couplings with a 0 seat and metric fine threads. All flanges are Code 6 or Code 62 (except 0)*. 2. Most other Japanese equipment uses couplings with a 0 seat and British Standard Pipe Parallel threads, usually called JIS (Japanese Industrial Standard) couplings.they are not interchangeable with British couplings, since the flare is not inverted. All flanges are Code 6 or Code 62 (except 0)*. Japanese 0 Flare Parallel Threads These Japanese 0 flare male connectors will mate with a Japanese 0 flare female only. The male and female have straight threads and a 0 seat. The seal is made on the 0 seat. The threads on the Japanese 0 flare connector conform to JIS B 0202, which are the same as the BSPP threads. Both the British and Japanese connectors have a 0 seat, but they are not interchangeable, because the British seat is inverted. Male Female Nominal Parallel Parallel Dash Size Thread Thread Thread Size (In.) Size O.D. (In.) I.D. (In.) Male 0 o Japanese 0 Flare Thread O.D. Thread I.D. 0 o Female * 0* *( 0 is a non-sae size flange) Japanese Tapered Pipe Thread The Japanese tapered pipe thread connector is identical to and fully interchangeable with the BSPT (tapered) connector. The Japanese connector does not have a 0 Flare, and will not mate with the BSPP female. The threads conform to JIS B 020, which are the same as BSPT threads. The seal on the Japanese tapered pipe thread connector is made on the threads. Japanese Tapered Pipe Thread o 47 Thread O.D. Thread I.D. Male Female Nominal Tapered Tapered Dash Size Thread Thread Thread Size (In.) Size I.D. (In.) O.D. (In.) Male Female

160 FAX: HYDRAULIC TECHNICAL DATA Hydraulic Coupling Identification, Foreign Thread Types continued Japanese continued Komatsu Style 0 Flare Komatsu Style 0 Flare Parallel Threads The Komatsu style 0 Flare parallel thread connector is identical to the Japanese 0 Flare parallel thread connector except for the threads. The Komatsu style connector uses Metric fine threads which conform to JIS B The Komatsu style connector seals on the 0 Flare. Metric Male Female Nominal Size Dash Thread Thread Thread Size (In.) (mm) Size O.D. (mm) I.D. (mm) M8x M22x M24x M0x Mx M6x M42x Komatsu Style Flange Fitting Komatsu Style Flange Fitting The Komatsu style Flange fitting is nearly identical to and fully interchangeable with the SAE Code 6 flange fitting. In all sizes the O-ring dimensions are different. When replacing a Komatsu style flange with an SAE style flange, an SAE style O-ring must always be used. Nominal Size Dash Flange A B Size (In.) (mm) O.D. (In.) (In.) (In.) * 0* *( 0 is a non-sae size flange) 60

161 FAX: HYDRAULIC TECHNICAL DATA Thread Identification Tools Measuring Tools To be sure you order the correct couplings, the measuring tools shown below should be used. They are stocked by the Summers Rubber Company and are available on order. Product Number: Contents: Calipers Seat Gauges (English) Seat Gauges (Metric) Thread Gauges Thread I.D. Guide Measuring Threads With the caliper, measure the thread diameter at the largest point (O.D. of male threads; I.D. of female threads). Using the thread gauge, determine the number of threads per inch. Comparison of gauge and coupling threads against a lighted background will assure accuracy of reading. Measuring Seat Angles Using the seat gauge, determine the angle of the seat, as illustrated. When the centerline of the seat gauge extends parallel with the projected longitudinal axis of the coupling, then the angles of the gauge and seat match. Compare the measurements taken to a coupling shown in coupling specification tables that appear in this catalog, or the specifications in the Gates Hydraulic Coupling International Thread Identification Guide. NOTE: Thread binding will occur when different thread configurations are used. DO NOT mix thread configurations. 6

162 FAX: HYDRAULIC TECHNICAL DATA Hose Assembly Routing Tips Proper hose installation is essential for satisfactory performance. If hose length is excessive, the appearance of the installation will be unsatisfactory and unnecessary cost of equipment will be involved. If hose assemblies are too short to permit adequate flexing and changes in length due to expansion or contraction, hose service life will be reduced. The following diagrams show proper hose installations which provide maximum performance and cost savings. Consider these examples in determining length of a specific assembly. WRONG RIGHT When radius is below the required minimum, use an angle adapter to avoid sharp bends. WRONG WRONG RIGHT RIGHT When hose installation is straight, allow enough slack in hose line to provide for length changes which will occur when pressure is applied. Use proper angle adapters to avoid sharp twist or bend in hose. WRONG RIGHT WRONG RIGHT Adequate hose length is necessary to distribute movement on flexing applications and to avoid abrasion. Prevent twisting and distortion by bending hose in same plane as the motion of the boss to which hose is connected. WRONG RIGHT WRONG RIGHT Route hose directly by using 4 and/or 90 adapters and fittings. Avoid excessive hose length to improve appearance. Avoid twisting of hose lines bent in two planes by clamping hose at change of plane. NO PRESSURE HIGH PRESSURE WRONG RIGHT Reduce number of pipe thread joints by using proper hydraulic adapters instead of pipe fittings. To allow for length changes when hose is pressurized, do not clamp at bends so that curves will absorb changes. Do not clamp high and low pressure lines together. 62

163 FAX: HYDRAULIC TECHNICAL DATA Hose Assembly Routing Tips continued WRONG WRONG RIGHT RIGHT High ambient temperatures shorten hose life so make sure hose is kept away from hot parts. If this is not possible, insulate hose. Elbows and adapters should be used to relieve strain on the assembly, and to provide neater installations which will be more accessible for inspection and maintenance. WRONG RIGHT WRONG RIGHT To avoid hose collapse and flow restriction, keep hose bend radii as large as possible. Refer to hose specification tables for minimum bend radii. Run hose in the installation so that it avoids rubbing and abrasion. Often, clamps are required to support long hose runs or to keep hose away from moving parts. Use clamps of the correct size. A clamp too large allows hose to move inside the clamp and causes abrasion. WRONG RIGHT When installing hose, make sure it is not twisted. Pressure applied to a twisted hose can result in hose failure or loosening of connections. Assembly of Reusable and Field Attachable Couplings Five Easy Steps. Be sure to thoroughly oil hose. 2. Put socket in vise as shown. Turning counterclockwise, thread hose into socket. Leave a gap of /2 to /6 between end of hose and inside shoulder of socket.. Oil insert thread on nipple thoroughly. 4. With clockwise motion, thread nipple into socket until nipple hex shoulders against ferrule.. Inspect assembly internally for cut or bulged tube obstructions and cleanliness. 6

164 FAX: HYDRAULIC TECHNICAL DATA Coupling Identification Thread Identification Tools Hydraulic Coupling Templates Advertising Number: 949 These templates provide a fast and easy way to measure North American Thread and flange ends, seat angles (7 and 4 ) and hose I.D. Stainless Steel Dial Caliper Product Number: Caliper features a big 6 measuring capacity and reads to Dial is easy to read and shockproof. Capable of four-way measurement... inside, outside, depth and step. Comes in an impact resistant, hard plastic case for protection. Metric and BSP Female Thread Identification Kit Product Number: A sturdy, attractive carrying case suitable for counter display and field sales calls. Contains male metric and BSP plugs for identifying thread size, pocket I.D. kit, and flow chart with step-by-step instructions. For female thread identification, simply couple with the mating male. For female threads, identification is made by chasing the threads with the corresponding male. 64

165 FAX: HYDRAULIC TECHNICAL DATA Hydraulic System Pressure Drop What Is Pressure Drop? As related to our business, pressure drop is the difference between the pressure of a fluid as it enters one end of a hydraulic hose assembly and the pressure of that fluid as it leaves the other end. There will be a difference in pressure, and it will be less. How much less depends on what is between the beginning and end of the hose assembly. Here are some examples of things that can influence the amount of pressure drop.. FRICTION This is the rubbing of fluid against the inside walls of the hose assembly. 2. TYPE OF FLUID Different fluids behave differently under pressure. Thicker fluids are moved with greater difficulty and will exhibit greater pressure drop.. TEMPERATURE OF THE FLUID Warming fluids thins them so they are moved more easily, as with automotive oil. 4. LENGTH OF HOSE ASSEMBLY The longer it is, the more surface there is for friction to decrease pressure.. SIZE (I.D.) OF HOSE Affects the fluid velocity for a given flow rate. Higher velocities result in greater pressure drop. Therefore, a larger I.D. hose will produce less pressure drop. 6. TYPE OF COUPLINGS AND ADAPTERS Any change in bore or change in direction (such as with 4 or 90 elbows) can increase the amount of pressure drop. 7. FLOW RATE Pressure drop increases with flow rate for same size hose. Who Cares About Pressure Drop? Suppose you need 4000 psi of output from a hose assembly for hydraulic equipment to run efficiently. There will be some pressure drop and you must allow for it in helping to plumb the system with Gates hose, couplings and adapters. This means that the input pressure to the hose assembly must be equal to the output plus the amount of pressure drop. If the pressure drop in this example is 0 psi, then you will need 40 psi of input. How Can You Determine The Amount Of Pressure Drop? That s the easy part of it. Contact a Summers Rubber Company representative who is trained and equipped to quickly solve such problems for you. He will need information from you for a PRESSURE DROP DATA FORM. An example of a Pressure Drop analysis printed below will be sent to you for your application. Sample Pressure Drop Analysis Input Variables:, Fittings Used: Flow Rate: (GPM). Standard Straight Fitting Viscosity: 20.0 (Centistokes) Angle Coupling Specific Gravity: 0.8 Free Hose Length: 20.0 (ft.) Total Hose Pressure (2) Dash Pressure Drop-Hose () Heat () Size Velocity Drop & Fitting Reynolds Gain Horsepower (/6 ) (Ft/Sec) (psi/ft) (psi) Number (BTUH) Loss * *Recommended hose size, based on velocity, pressure drop, heat gain and hp loss. () Reynolds Number = inertia flow forces indicates the type of flow. friction forces (or viscosity) Reynolds No. Range Type of Flow aminar transient turbulent (2) Heat Gain is the total amount of energy converted to heat energy which will raise the fluid temperature if it is not dissipated. () Horsepower Loss is a measure of the conversion of mechanical energy to heat energy and is related to system heat gain. 6

166 Bend Radius The radius of a bent section of hose is always measured to the innermost surface of the curved portion. Minimum Bend Radius This is the tightest that a hose can be bent prior to exerting excessive forces that can cause kinking or damage. Impulse testing is conducted at minimum bend radius in accordance with SAE standards for appropriate hoses. Bend radius is listed with hose data for each hose type. Use Gates MegaSys hoses for optimum bend radii FAX: HYDRAULIC TECHNICAL DATA Hose Bend Radius Considerations Flow Capacities of Hose Assemblies at recommended Flow Velocities The Nomographic Chart on page 67 will help you select the correct hose size for a given hydraulic system. The velocity of the hydraulic fluid should not exceed the range shown in the right-hand column. When oil velocities are higher than recommended in the chart, the results are turbulent flow with loss of pressure and excessive heating. Higher velocities may be used if the flow of hydraulic fluid is intermittent or for only short periods of time. Velocity of hydraulic fluid in suction lines should always fall within the range recommended to assure efficient pump operation. The following example will help you to use this chart: Determine the hose assembly size needed to carry 0 gallons of oil per minute and figure the velocity of the oil through the hose assembly. The assembly is to be used in a pressure line and the flow will be continuous. Locate the flow, 0 gallons per minute (left-hand column), and velocity, 0 ft. per second (right-hand column), since it is near the center of the recommended range. Lay a straightedge across these two points. The straightedge crosses the center column nearest to the 8 hose assembly. Keeping the straightedge on 0 gallons per minute in the left-hand column, cross the center column at the 4 assembly, the 8 assembly and the 2 assembly. Reading the right-hand column, the straightedge crosses it at 7., 0. and 6 ft. per second, respectively. Since 7. and 0. are within the recommended velocity range for pressure lines, either a 4 or 8 hose assembly is required. Suction hose problems are solved in a similar manner, except that the recommended velocity range for intake line (right-hand column) is used. 66

167 FAX: HYDRAULIC TECHNICAL DATA Nomographic Chart Indicating Flow Capacity of Hose Assemblies at Recommended Flow Velocities Selecting the Right Hose Size With this nomograph, you can easily select the correct I.D. size, Desired Flow Rate (GPM) and Recommended Velocity (FPS). If you know any two factors, you can determine the third. The chart below is based on this formula: To use this nomograph:. Pick the two known values. 2. Lay a straightedge to intersect the two values.. Intersection on the third vertical line gives you value of that factor. Area (sq. in.) = Flow Rate (GPM) x Velocity (ft./sec.) EXAMPLE: A flow rate of 4GPM is obtained through a pressure hose with a 2 I.D. A line would intersect the two values and cross the Velocity line at 6. indicating 6. FPS. 67

168 FAX: HYDRAULIC TECHNICAL DATA Selection, Installation and Maintenance of Hose and Hose Assemblies SAE J27 May 86 SAE Recommended Practice Report of the Fluid Conductors and Connectors Technical Committee, approved September 979 and reaffirmed May Scope Hose (also includes hose assemblies) has a finite life and there are a number of factors which will reduce its life. This recommended practice is intended as a guide to assist system designers and/or users in the selection, installation, and maintenance of hose. The designers and users must make a systematic review of each application and then select, install, and maintain the hose to fulfill the requirements of the application. The following are general guidelines and are not necessarily a complete list. WARNING: IMPROPER SELECTION, INSTALLATION, OR MAINTENANCE MAY RESULT IN PREMATURE FAILURES, BODILY INJURY, OR PROPERTY DAMAGE. 2. Selection The following is a list of factors which must be considered before final hose selection can be made: 2. Pressure After determining the system pressure, hose selection must be made so that the recommended maximum operating pressure is equal to or greater than the system pressure. Surge pressures higher than the maximum operating pressure will shorten hose life and must be taken into account by the hydraulic designer. 2.2 Suction Hoses used for suction applications must be selected to insure the hose will withstand the negative pressure of the system. 2. Temperature Care must be taken to insure that fluid and ambient temperatures, both static and transient, do not exceed the limitations of the hose. Special care must be taken when routing near hot manifolds. 2.4 Fluid Compatibility Hose selection must assure compatibility of the hose tube, cover, and fittings with the fluid used. Additional caution must be observed in hose selection for gaseous applications. 2. Size Transmission of power by means of pressurized fluid varies with pressure and rate of flow. The size of the components must be adequate to keep pressure losses to a minimum and avoid damage to the hose due to heat generation or excessive turbulence. 2.6 Routing Attention must be given to optimum routing to minimize inherent problems. 2.7 Environment Care must be taken to insure that the hose and fittings are either compatible with or protected from the environment to which they are exposed. Environmental conditions such as ultraviolet light, ozone, salt water, chemicals, and air pollutants can cause degradation and premature failure and, therefore, must be considered. 2.8 Mechanical Loads External forces can significantly reduce hose life. Mechanical loads which must be considered include excessive flexing, twist, kinking, tensile or side loads, bend radius, and vibration. Use of swivel type fittings or adapters may be required to insure no twist is put into the hose. Unusual applications may require special testing prior to hose selection. 2.9 Abrasion While a hose is designed with a reasonable level of abrasion resistance, care must be taken to protect the hose from excessive abrasion which can result in erosion, snagging, and cutting of the hose cover. Exposure of the reinforcement will significantly accelerate hose failure. 2.0 Proper End Fitting Care must be taken to insure proper compatibility exists between the hose and coupling selected based on the manufacturer s recommendations substantiated by testing to industry standards such as SAE J7d (November, 976). 2. Length When establishing proper hose length, motion absorption, hose length changes due to pressure, as well as hose and machine tolerances must be considered. 2.2 Specifications and Standards When selecting hose, government, industry, and manufacturers specifications and recommendations must be reviewed as applicable. 2. Hose Cleanliness Hose components vary in cleanliness levels. Care must be taken to insure that the assemblies selected have an adequate level of cleanliness for the application. 2.4 Electrical Conductivity Certain applications require that hose be non-conductive to prevent electrical current flow. Other applications require the hose to be sufficiently conductive to drain off static electricity. Hose and fittings must be chosen with these needs in mind.. Installation After selection of proper hose, the following factors must be considered by the installer:. Pre-Installation Inspection Prior to installation, a careful examination of the hose must be performed. All components must be checked for correct style, size, and length. In addition, the hose must be examined for cleanliness, I.D. obstructions, blisters, loose cover, or any other visible defects..2 Follow Manufacturers Assembly Instructions. Minimum Bend Radius Installation at less than minimum bend radius may significantly reduce hose life. icular attention must be given to preclude sharp bending at the hose/fitting juncture..4 Twist Angle and Orientation Hose installations must be such that relative motion of machine components produces bending of the hose rather than twisting.. Securement In many applications, it may be necessary to restrain, protect, or guide the hose to protect it from damage by unnecessary flexing, pressure surges, and contact with other mechanical components. Care must be taken to insure such restraints do not introduce additional stress or wear points..6 Proper Connection of Ports Proper physical installation of the hose requires a correctly installed port connection while insuring that no twist or torque is put into the hose..7 Avoid External Damage Proper installation is not complete without insuring that tensile loads, side loads, kinking, flattening, potential abrasion, thread damage, or damage to sealing surfaces are corrected or eliminated..8 System Check Out After completing the installation, all air entrapment must be eliminated and the system pressurized to the maximum system pressure and checked for proper function and freedom from leaks. NOTE: Avoid potential hazardous areas while testing. 4. Maintenance Even with proper selection and installation, hose life may be significantly reduced without a continuing maintenance program. Frequency should be determined by the severity of the application and risk potential. A maintenance program should include the following as a minimum: 4. Hose Storage Hose products in storage can be affected adversely by temperature, humidity, ozone, sunlight, oils, solvents, corrosive liquids and fumes, insects, rodents, and radioactive materials. Storage areas should be relatively cool and dark and free of dust, dirt, dampness, and mildew. 4.2 Visual Inspections Any of the following conditions requires replacement of the hose: (a) Leaks at fitting or in hose. (Leaking fluid is a fire hazard.) (b) Damaged, cut, or abraded cover. (Any reinforcement exposed.) (c) Kinked, crushed, flattened, or twisted hose. (d) Hard, stiff, heat cracked, or charred hose. (e) Blistered, soft, degraded, or loose cover. (f) Cracked, damaged, or badly corroded fittings. (g) Fitting slippage on hose. 4. Visual Inspections The following items must be tightened, repaired, or replaced as required: (h) Leaking port conditions. (i) Clamps, guards, shields. (j) Remove excessive dirt buildup. (k) System fluid level, fluid type, and any air entrapment. 4.4 Functional Test Operate the system at maximum operating pressure and check for possible malfunctions and freedom from leaks. NOTE: Avoid potential hazardous areas while testing. 4. Replacement Intervals Specific replacement intervals must be considered based on previous service life, government or industry recommendations, or when failures could result in unacceptable down time, damage, or injury risk. 68

169 FAX: INDUSTRIAL TECHNICAL DATA Industrial Threading Thread Seal Washer Seal Mechanical Seal Ground Joint Type Shown Metal to Metal or Metal to Seal Abbreviation System Name Seal Method Thread Compatibility Examples BSPP British Standard Pipe Parallel Washer Seal Male BSPP Female BSPP Female BSPP Male BSPP BSPTr British Standard Pipe Tapered Thread Seal Male BSPTr Female BSPTr, BSPP* or Female BSPTr Male BSPTr Washer Seal* CHT American Standard Fire Hose Coupling Washer Seal Male NH (NST) Female NH (NST) Thread ( National Hose Thread is Female NH (NST) Male NH (NST) Chemical Hose Thread, and is also Not compatible with other systems. known as Booster Hose Thread) The thread is used on both /4 and hose. GHT Garden Hose Thread Washer Seal Male GHT Female GHT Female GHT Male GHT Not compatible with other systems. IPS Iron Pipe Straight Thread Washer Seal Generic name for Straight Pipe Thread (NPSH) IPT Iron Pipe Thread Generic name for All Pipe Thread More information is needed. JIC (7 ) Joint Industrial Committee Mechanical Seal Used with other mating JIC threads Metal to Metal or O-ring Seal NH American Standard Fire Hose Washer Seal Male NH (NST) Female NH (NST) or Coupling Thread Female NH (NST) Male NH (NST) NST National Hose Thread Not compatible with other systems. Thread pitch also known as and diameters of fire threads may vary according National Standard Thread to local and municipal regulations. Consult factory. NPT American Standard Tapered Thread Seal Male NPT Female NPT, NPTF, NPSM*, NPSH* Pipe Thread or Female NPT Male NPT, NPTF National Pipe Tapered Washer Seal* NPTF American Standard Tapered Thread Seal Male NPTF Female NPTF 2, NPT, NPSM*, NPSH* Pipe Fuel Dryseal Thread or Female NPTF Male NPTF 2, NPT National Pipe Tapered Fine Washer Seal* NPSH American Standard Straight Washer Seal Male NPSH Female NPSH, NPSM Pipe for Hose Couplings Female NPSH Male NPSH, NPT, NPTF, NPSM National Pipe Straight Hose NPSM American Standard Straight Washer Seal Male NPSM Female NPSM Mechanical Joints Female NPSM Male NPSM, NPT, NPTF National Pipe Straight Mechanical Both mating fittings must be of the same type. NPSM American Standard Straight Mechanical Seal Male NPSM Female NPSM Mechanical Joints Metal to Metal or Female NPSM Male NPSM, NPT, NPTF National Pipe Straight Mechanical O-ring Seal Both mating fittings must be of the same type. TIPT Tapered Iron Pipe Thread Thread Seal Generic name for Tapered Pipe Thread (NPT) Thread sealant is required to seal the threads on Thread Seal connections, except for NPTF as noted below. 2 NPTF threads do not require thread sealant for initial use when used with mating NPTF threads. Once NPTF are used, they require sealing compound for future use. An NPSM or NPSH Ball Seat Female requires a matching internal bevel on the NPSM, NPSH or NPT male. NOTE: Compatibility of thread type DOES NOT insure compatibility of the fittings, due to sealing design and thread lengths. ALWAYS USE MATING FITTINGS OF THE SAME TYPE. 69

170 FAX: INDUSTRIAL TECHNICAL DATA Identify Industrial Threads It is important to identify the threads before ordering couplings. Identifying threads can sometimes be the most difficult and frustrating part of coupling selection. However, without the right combination of threads, you may not provide a functional or safe connection. The diameters, threads per inch (TPI) and thread pitch, etc. are necessary to completely identify a thread. Ring, Plug and GO/NOGO gauges are required to accurately gauge or identify threads. In the field, in the absence of these gauges, thread leaf gauges can be used to identify the Threads Per Inch (TPI) and the thread pitch. On threads you have determined to be straight threads, a caliper can be used to measure the Outside Diameter of the Male (ODM) or the Inside Diameter of the Female (IDF). A caliper can also be used to take measurements of tapered thread diameters. However, these are more difficult to define because of the taper. Fortunately, there are few tapered threads to deal with and these can usually be identified from the nominal ODM and the TPI. However, identifying the thread may not fully identify what is needed in a mating fitting. The application is the primary limiting factor on the thread type used. Summers Rubber Company offers products with a wide variety of threads used with hoses, pipes and hydraulics. When attempting to choose a fitting, it is always advisable to first identify the thread to which it must connect. This may entail checking with a fitting or equipment manufacturer. The fire hose thread specifications for some local municipal fire equipment and hydrants may vary according to local specifications. These can generally be most easily identified by contacting the local fire department responsible for the hydrant. The most common thread used on fire equipment is National Standard Thread (NST), also known as National Hose thread (NH). When it is not possible to identify the thread:. Determine the number of threads per inch by measuring the distance from peak of thread to peak of thread across the largest number of whole threads. Then divide the number of threads by the measurement. (This will provide the TIP.) 2. Check to see if the thread is straight or tapered. a. Straight Threads Measure the Outside Diameter of the Male (ODM) or the Inside Diameter of the Female (IDF), from peak of thread to peak of thread. b. Tapered Threads Measure the Outside Diameter of the Male (ODM) at the large end and the small end, or the Inside Diameter of the Female (IDF) at the large end and the small end, from peak of thread to peak of thread. Then measure the Outside Diameter (OD) of the unthreaded pipe. Once the application and these two pieces of information have been determined, the thread can generally be determined. When in doubt, contact the factory. Male STRAIGHT THREAD Female Male TAPERED THREAD Female Peak to Peak Peak to Peak O.D. I.D. O.D. I.D. Peak to Peak Peak to Peak A Normal Engagement Length of NPT Thread in Inches A* *Dimensions given do not allow for variations in tapping or threading. Pressure Conversions PSI x.0690 = Bars Bar = 4. PSI 70

171 FAX: INDUSTRIAL TECHNICAL DATA Dimensions of Seamless and Welded Steel Pipe ASA-B6.0 and B6.9 Nominal Outside Pipe Schedule Wall Thickness (In.) Pipe Size Diameter Extra XXX (In.) (In.) Stand Strong Strong Dimensions of 0 lb. Steel Flanges ASA Nominal Flange O.D. of Diameter of Number Diameter of Diameter Pipe Size O.D. Thickness* Raised Face Bolt Circle of Bolts Bolt Holes of Bolts */6 raised face is included in the Thickness. All dimensions are in inches except number of bolts Dimensions of Tank Truck Flanges (TTMA Drilling) Nominal Flange Diameter of Number Diameter of Diameter Pipe Size O.D. Thickness* Bolt Circle of Bolts Bolt Holes of Bolts *Listed Thickness is for Aluminum Flanges. All dimensions are in inches except number of bolts Conversion Table Feet of Water to Inches of Mercury Feet of Water Inches of Mercury

172 FAX: INDUSTRIAL TECHNICAL DATA End Force Chart in Pounds Hose I.D (In.) psi psi psi psi psi psi psi psi psi , , ,27,7, ,227,47,964 2,44 4, ,060,44,767 2,2 2,827,4 7, ,27,88 2,,42,770,027 6,28 2, ,964 2,94,927 4,909,89 7,84 9,88 9,6 6 2,44 2,827 4,24,6 7,069 8,482,0 4,7 28, ,,027 7,40 0,0 2,66,080 20,06 2, 0, ,927 7,84,78,708 9,6 2,62,46 9,270 78,40 2 2,6,0 6,96 22,620 28,274,929 4,29 6,49,098 NOTE: For hose I.D.s from 4 to 2, the force in pounds is greater than the psi. FORCE is the dynamic power which is exported longitudinally through a hose, towards the ends. To arrive at the number of pounds of FORCE exerted, you merely multiply the area of the I.D. times the working pressure being used. Area of a circle is: π x r 2 (pi [.46] times radius squared). Force = Area x Pressure Thread Sealing Tips Sealing NPT threads can be an exasperating experience if certain techniques are not followed. The following tips will help alleviate many common problems in thread sealing: 0. Always use some type of sealant (tape or paste) and apply sealant to male threads only. If using a hydraulic sealant, allow sufficient curing time before system is pressurized. 02. When using tape sealant, wrap the threads in a clockwise motion starting at the first thread and, as layers are applied, work toward the imperfect (vanishing) thread. If the system that the connection being made to cannot tolerate foreign matter (i.e. air systems), leave the first thread exposed and apply the tape sealant as outlined above. 0. When using paste sealant, apply to threads with a brush, using the brush to work the sealant into the threads. Apply enough sealant to fill in all the threads all the way around. 04. When connecting one stainless steel part to another stainless steel part that will require future disassembly, use a thread sealant that is designed for stainless steel. This stainless steel thread sealant is also useful when connecting aluminum to aluminum that needs to be disconnected in the future. These two materials gall easily, and if the correct sealant is not used, it can be next to impossible to get apart. 0. When connecting parts made of dissimilar metals (i.e. steel and aluminum), standard tape or paste sealant performs satisfactorily. 06. For sizes 2 and below, tape or paste performs satisfactorily. When using thread tape, four wraps (covering all necessary threads) is usually sufficient. 07. For sizes 2 2 and above, thread paste is recommended. If thread tape is used, eight wraps (covering all necessary threads) is usually sufficient. Apply more wraps if necessary. 08. For stubborn-to-seal threads, apply a normal coating of thread paste followed by a normal layer of thread tape. 09. For extremely-stubborn-to-seal threads, apply a normal coating of thread paste followed by a single layer of gauze bandage followed by a normal layer of thread tape. CAUTION: When this procedure is done, the connection becomes permanent. Extreme measures will be necessary to disconnect these components. All other measures to seal the threads should be explored prior to use of this technique. 0. Over tightening threads can be just as detrimental as insufficient tightening. For sizes 2 and below, hand tighten the components and, with a wrench, tighten three full turns. For sizes 2 2 and above, hand tighten the components and, with a wrench, tighten two full turns. 72

173 FAX: INDUSTRIAL TECHNICAL DATA Thread Dimensions Nominal Dimensions of Standard Threads NH Pipe NPT NPSH NPSM (NST) BSPP BSPT Size O.D. ODM IDF ODM IDF ODM IDF Size (In.) (In.) TPI TPI (max) (min) TPI (max) (min) TPI ODM TPI (max) (min) TPI (In.) v ODM Outside Diameter of the Male IDF Inside Diameter of the Female TPI Threads Per Inch GHT ( 4 ).062 ODM, 2 TPI NOTE: Female NPT (Tapered Pipe) thread is not available on hose swivel nuts. Male NPT Thread Size Fittings Size Chart Male NST Thread Size Corrosion Resistance of Coupling Material CAUTION: The following data has been complied from generally available sources and should not be relied upon without consulting and following the specific recommendations of the manufacturer regarding particular coupling materials. Ratings Metal Non-Metal Gasket/Seal Material Excellent A Acceptable T Teflon 2 Good X Not Recommended V Viton Fair Contact Factory E EPDM X Not Recommended N Neoprene Contact Factory B Buna N NOTE:. Ratings given are based at 70 F. Chemical compatibility varies greatly with temperature. For applications at temperatures other than 70 F, contact the factory for recommendations. 2. Gasket/Seal Materials are not necessarily listed in order of preference.. Chemical Resistance of a material does not necessarily indicate the suitability of a fitting in a given application due to variables such as improper clamp and coupling application, special hose construction, gasket material, etc. Special caution should be taken when handling hazardous materials. 7

174 FAX: INDUSTRIAL TECHNICAL DATA Corrosion Agents to Materials Complete Legend See Page 7 AGENT Aluminum Brass Bronze Malleable Iron Carbon Steel Monel Stainless Steel, 04 Stainless Steel, 6 Nylon Polypropylene Seal Material Acetate Solvents: Crude X X 2 2 A X T Acetate Solvents: Pure X A X T Acetic Acid: 80% X X X X X TEVNB Acetic Acid: 0% 2 X X X 2 2 X X TEVNB Acetic Acid: 20% 2 X X X 2 2 X X TEVNB Acetic Acid: 0% 2 X 2 X 2 X X TEVNB Acetic Anhydride 2 X X X TNB Acetone A X TE Acetylene X X 2 2 X X TEVNB\ Alcohols: Amyl Alcohol A A TEVNB Alcohols: Benzyl Alcohol X A TVB Alcohols: Butyl Alcohol 2 2 A A TEVN Alcohols: Diacetone Alcohol X A TE Alcohols: Ethyl Alcohol X A TEVNB Alcohols: Hexyl Alcohol A Alcohols: Isobutyl Alcohol A Alcohols: Isopropyl Alcohol A A TEVNB Alcohols: Methyl Alcohol Methanol A A TENB Alcohols: Octyl Alcohol A Alcohols: Propyl Alcohol X A TEVNB Aluminum Chloride Aqu. X X X X X X X A A TEVNB Aluminum Fluoride Sat. 2 X 2 X 2 X A TEVNB Aluminum Nitrate Sat. X X 2 2 A A TEVNB Aluminum Potassium Sulfate Alum X 2 X 2 X A TEVNB Aluminum Sulfate Sat. X X 2 X 2 2 A A TEVNB Ammonia Anhydrous X X 2 A X TENB Ammonia Gas X X X X A X TENB Ammonia Nitrate X Ammonium Biflouride X X 2 X A TEVB Ammonium Carbonate Sat. 2 X X A A TEVNB Ammonium Casenate A Ammonium Chloride Sat. X X 2 X 2 X X A A TEVNB Ammonium Hydroxide Sat. 2 X X X 2 2 A A TEVNB Ammonium Nitrate 2 X X X X A A TENB Ammonium Phosphate 0-40% X X X X 2 2 A A TEVNB Ammonium Sulfate 0-40% X X X 2 X 2 A A TEVNB Aniline X 2 X 2 X X TV Arsenic Acid X X 2 X X 2 2 X A TEVNB Asphalt 2 2 X X TV Barium Carbonate Sat. X A A TEVNB Barium Chloride Sat X A A TEVNB Barium Hydroxide Sat. X 2 X A A TEVNB Barium Sulfate X A A TEVNB Barium Sulfide X X X 2 X 2 2 A A TEVNB Beer A A TEVNB Benzaldehyde X X X TE Benzene, Benzol A X TV Benzine A X Benzoic Acid X X X TVN Bleach 2.% Active Chlorine X X X X A TEVN Ratings given are based at 70 F. 74 Legend Metal: Excellent; 2 Good; Fair; X Not Recommended; and Contact Factory Legend Non-Metal: A Acceptable; X Not Recommended; and Contact Factory Legend Gasket/Seal Material: T Teflon; V Viton; E EPDM; N Neoprene; and B Buna N

175 FAX: INDUSTRIAL TECHNICAL DATA Corrosion Agents to Materials Complete Legend See Page 7 continued AGENT Aluminum Brass Bronze Malleable Iron Carbon Steel Monel Stainless Steel, 04 Stainless Steel, 6 Nylon Polypropylene Seal Material Borax X X A TEVNB Boric Acid X 2 X 2 X A TEVNB Brine Acid 2 2 X A TEVNB Bromic Acid X X X X X A TEVN Bromine Liquid 2 X X X X TV Butadiene, Butylene X X TVNB Butane X X TV Butyl Acetate A X T Butyric Acid 2 2 X X A A TV Calcium Bisulfate X X X X X 2 X A T Calcium Bisulfide 2 2 A A TVB Calcium Bisulfite X X 2 X X 2 X A TVNB Calcium Carbonate X A A TEVB Calcium Chloride Sat A A TEVNB Calcium Hydroxide Sat. X 2 X A A TEVNB Calcium Hypochlorite Sat. X X X X X X 2 X A TEV Carbon Bisulfide X 2 2 X 2 2 A X TV Carbon Dioxide Dry A A TENB Carbon Dioxide Wet X 2 2 X A TENB Carbon Disulfide X 2 2 X 2 2 A X TV Carbon Monoxide 2 A A TEVNB Carbon Tetrachloride X 2 A X TV Carbonic Acid X A TEVNB Castor Oil X A TEVNB Caustic Potash X X 2 A A TEVNB Cellosolves X A TE Chlorine Liquid 2 2 X X TV Chloroform X X X TV Chlorosulfonic Acid X X 2 2 X X X X T Clorox Bleach,.% CL X X 2 X TEVB Chromic Acid 0% 2 X X X X X X TVNB Citric Acid X X X 2 X A TEVNB Coke Oven Gas X X TEVN Copper Chloride X X X X X X X A A TEVNB Copper Cyanide X X X X 2 2 X TEVNB Copper Sulfate X X X X X 2 A A TEVNB Crysylic Acid Conc. 2 2 X X X TEV Cyclohexane A X TVB Detergents A A TEVNB Dextrose 2 2 A A TEVNB Diesel Fuels 2 A X TVB Diethylamine 2 X X 2 2 X A TN Disodium Phosphate A A TEV Ethers A X TB Ethyl Acetate A X T Ethyl Chloride A X TEVB Ethylene Chloride 2 2 A X TV Ethylene Dichloride 2 X A X TV Ethylene Glycol A X TEVNB Ethylene Oxide X X X X T Ratings given are based at 70 F. Legend Metal: Excellent; 2 Good; Fair; X Not Recommended; and Contact Factory Legend Non-Metal: A Acceptable; X Not Recommended; and Contact Factory Legend Gasket/Seal Material: T Teflon; V Viton; E EPDM; N Neoprene; and B Buna N 7

176 FAX: INDUSTRIAL TECHNICAL DATA Corrosion Agents to Materials Complete Legend See Page 7 continued AGENT Aluminum Brass Bronze Malleable Iron Carbon Steel Monel Stainless Steel, 04 Stainless Steel, 6 Nylon Polypropylene Seal Material Fatty Acids X 2 A A TVNB Ferric Chloride X X 2 X X X X X A TEVNB Ferric Hydroxide 2 A TEVNB Ferric Nitrate 0-0% X X X X X 2 2 X A TEVNB Ferric Sulfate X X X X 2 X A TEVNB Ferrous Chloride Sat. X X 2 X X X X A TEVNB Ferrous Sulfate X 2 2 X A TEVNB Fluboric Acid X 2 X A TEVNB Formaldehyde 0% 2 2 X 2 X A TEN Formic Acid Anhyd. X 2 X 2 X A TEVN Freon X 2 2 A X TVNB Freon X A X TVNB Freon X A X TN Fruit Juices 2 2 X 2 2 A A TVNB Fuel Oil A X TVNB Furfural A X TEN Gasoline Refined A X TVNB Gasoline Sour X X 2 2 A X TVNB Gelatin X A A TEVNB Glucose A A TEVNB Glue A TEVNB Glycerine 2 2 A A TEVNB Glycols A A TEVNB Heptane A X TVNB Hexane A X TVNB Hydrobromic Acid 0% X X X X X X X X A TEV Hydrobromic Acid 20% X X X X X X X X A TEV Hydrobromic Acid 20% X X X X X X X A TEVNB Hydrobromic Acid 8% X X X X X X X X A TEVN Hydrocyanic Acid 2 X X X A TEVN Hydrofluosilicic Acid 0-0% X 2 X X 2 X 2 X TEVNB Hydrogen Chloride Dry Gas X 2 2 X A TEVN Hydrogen Gas X A TEVNB Hydrogen Peroxide 0% X X X 2 X A TEV Hydrogen Sulfide Aqu. 2 X 2 X A TE Hypochlorous Acid X X X X X X X X X TEV Iodine X X X X X X A TEV Isopropyl Ether A X T Jet Fuel JP4, JP X X TV Kerosene X X TVNB Ketones A X T Lactic Acid 2% 2 2 X X A A TEVN Lactic Acid 80% 2 2 X X A A TEVN Lard Oil A A TVB Lead Acetate X X X X X A TENB Lead Chloride X 2 2 X TVNB Lead Sulfate X X X TEVNB Lime Sulphur X X X X X A TEVN Linoleic Acid 2 X X X A TVB Linseed Oil A A TVNB Ratings given are based at 70 F. 76 Legend Metal: Excellent; 2 Good; Fair; X Not Recommended; and Contact Factory Legend Non-Metal: A Acceptable; X Not Recommended; and Contact Factory Legend Gasket/Seal Material: T Teflon; V Viton; E EPDM; N Neoprene; and B Buna N

177 FAX: INDUSTRIAL TECHNICAL DATA Corrosion Agents to Materials Complete Legend See Page 7 continued AGENT Aluminum Brass Bronze Malleable Iron Carbon Steel Monel Stainless Steel, 04 Stainless Steel, 6 Nylon Polypropylene Seal Material Liquors: Black Liquor X X X X A TEVNB Liquors: Green Liquor 2 A TEVNB Liquors: Sugar Liquors Cane A A TEVNB Liquors: Sugar Liquors Beet 2 2 A A TEVNB Liquors: Sulfate Liquor 2 X X 2 2 X A TVNB Liquors: Sulfite Liquor X X X X 2 2 X X TVNB Liquors: Tanning Liquor 2 X A TVNB Liquors: White Liquor Pulp 2 X X X 2 2 X A TEVNB Lubricants Oil A X TVNB Magnesium Carbonate X A TEVNB Magnesium Chloride X X 2 X A TEVNB Magnesium Hydroxide X A TEVNB Magnesium Nitrate X A TEVNB Magnesium Oxide X Magnesium Sulfate X A TEVNB Maleic Acid 2 X 2 X A TEV Mercuric Chloride X X X X X X X A TEVB Mercuric Cyanide X X X X X A TEVB Mercury X X X 2 A A TEVNB Methane 2 2 A X TEVNB Methanol A A TENB Methyl Bromide X X X TV Methyl Ethyl Ketone A X TE Methyl Isobutyl Ketone A X T Methyl Methacrylate 2 X 2 2 X A T Methylene Chloride A X T Milk X X 2 X A A TEVNB Mineral Oil A A TVNB Muriatic Acid X X X X X A TV Napthalene A A TV Naptha A X TVB Nickel Chloride X X X X 2 X A TEVNB Nickel Sulfate X X 2 2 X A TEVNB Nitric Acid 00% X X X X 2 X X TV Nitric Acid 0% X X X X X 2 X X TV Nitric Acid 0% X X X X X X X TV Nitrobenzene A A T Oils: Castor Oil A A TEVNB Oils: Coconut Oil A A TVB Oils: Corn Oil A A TVNB Oils: Cotton Seed Oil A A TVNB Oils: Fuel Oil A X TVNB Oils: Linseed Oil A A TVNB Oils: Mineral Oil A A TVNB Oils: Silicon Oil A A TEVB Oils: Vegetable Oil A X TVNB Oleic Acid A X TB Oleum 2 X X 2 X 2 2 X X TV Oxalic Acid Sat. 2 2 X 2 X X X A TEV Oxygen X X TEVNB Ratings given are based at 70 F. Legend Metal: Excellent; 2 Good; Fair; X Not Recommended; and Contact Factory Legend Non-Metal: A Acceptable; X Not Recommended; and Contact Factory Legend Gasket/Seal Material: T Teflon; V Viton; E EPDM; N Neoprene; and B Buna N 77

178 FAX: INDUSTRIAL TECHNICAL DATA Corrosion Agents to Materials Complete Legend See Page 7 continued AGENT Aluminum Brass Bronze Malleable Iron Carbon Steel Monel Stainless Steel, 04 Stainless Steel, 6 Nylon Polypropylene Seal Material Palmitic Acid Sat X A TVB Paraffin A A TVNB Perchloroethylene X X TV Petrolatum A TVNB Phenol Carbolic Acid X 2 X X TV Phosphoric Acid 2-0% X X 2 X X X A TEVN Phosphoric Acid 0-8% X X X X X A TEV Photographic Solutions X X X TVNB Phthalic Anhydride X X TEV Picric Acid X X X X 2 2 X TEVNB Plating Solutions: Brass Plating Solution 2 X A TEVNB Plating Solutions: Cadium Plating Solution 2 X A TEVNB Plating Solutions: Chrome 40% Plating Solution X 2 2 X X 2 2 X A TEVN Plating Solutions: Copper (Cyanide) Plating Solution X A TEVNB Plating Solutions: Gold Plating Solution X A TEVNB Plating Solutions: Iron Plating Solution X A TEVB Plating Solutions: Lead Plating Solution X A TEVNB Plating Solutions: Nickel Plating Solution X A TEVNB Plating Solutions: Silver Plating Solution X A TEVNB Plating Solutions: Tin Plating Solution X A TEVNB Plating Solutions: Zinc Plating Solution X A TEVNB Potassium Acetate X X X 2 A A TEVB Potassium Bicarbonate 0% X A A TEVNB Potassium Carbonate 0% X 2 X 2 2 A A TEVNB Potassium Chlorate 0% 2 X X X A TEVNB Potassium: Chloride 0% X X 2 2 A A TEVNB Potassium Chromate 0% X A TEVB Potassium Cyanide Solution 0% X X X X A TEVNB Potassium Dichromate 0% X A TEVB Potassium Hydroxide 90% X X X 2 X X A TENB Potassium Nitrate 80% X A TEVNB Potassium Permanganate 20% X A TEVN Potassium Sulfate 0% A A TEVNB Propane X X TVB Propylene Gylcol A A TVNB Propylene Oxide 90% X X TE Pyridine A X T Pyrogallic Acid X X TVNB Silver Nitrate X X X X X 2 X A TEVNB Soap Solutions A A TEVNB Sodium Acetate 2 2 X A A TEN Sodium Bicarbonate 20% A A TEVNB Sodium Bisulfate X 2 2 A A TEVNB Sodium Bisulfite X 2 X X A A TEVNB Sodium Borate A A TEVNB Sodium Carbonate X A A TEVNB Sodium Chlorate 0% X 2 2 X A TEVNB Sodium Chloride 0% X X A TEVNB Sodium Cyanide X X X 2 X A A TEVNB Sodium Dichromate 2 X X X A TE Sodium Hydroxide 70% X X X 2 2 X A TENB 78 Ratings given are based at 70 F. Legend Metal: Excellent; 2 Good; Fair; X Not Recommended; and Contact Factory Legend Non-Metal: A Acceptable; X Not Recommended; and Contact Factory Legend Gasket/Seal Material: T Teflon; V Viton; E EPDM; N Neoprene; and B Buna N

179 FAX: INDUSTRIAL TECHNICAL DATA Corrosion Agents to Materials Complete Legend See Page 7 continued AGENT Aluminum Brass Bronze Malleable Iron Carbon Steel Monel Stainless Steel, 04 Stainless Steel, 6 Nylon Polypropylene Seal Material Sodium continued: Sodium Hydroxide 0% X X X A TENB Sodium Hydroxide 0% X 2 2 X A TENB Sodium Hypochlorite X X X X X X A TEV Sodium Metaphosphate X X 2 X X X TEVNB Sodium Nitrate 40% A A TENB Sodium Perborate 0% 2 X X A TEVNB Sodium Peroxide 0% 2 X X X A TEVNB Sodium Silicate A A TEVNB Sodium Sulfate A A TEVNB Sodium Sulfide 0% X X X X A TEVNB Sodium Thiosulphate 2 X X X A A TEVNB Stannic Chloride X X X X X X X X A TEVNB Stannous Chloride X X X X X X X TEVNB Steam X Stearic Acid A A TVNB Stoddard s Solvent X A TVB Sulfur Chloride X X X X X X TV Sulfur Dioxide Dry X A TE Sulfur Trioxide 2 2 X X X TEV Sulfuric Acid to 0% X 2 X X X X X X A TEVNB Sulfuric Acid 00% X X X 2 X X X TV Sulfurous Acid 2 2 X X X X X A TV Tannic Acid X X X X A TEVNB Tartaric Acid 2 A A TVNB Titanium Tetrachloride X X X X X TV Toluene A X TVB Tetrahydrofuran X 2 2 A X T Tomato Juice X A TEVNB Trichloroethylene 2 2 A X TV Triethanolamine 2 X A X TEVN\ Triethylamine A X TVB Trisodium Phosphate 0% X A A TVNB Turpentine 2 X 2 2 X X TVB Urea 0% A A TEVNB Urine 2 X A TEVNB Vinegar 2 X X A TEVN Water Acid Mine X X X X X A TEVNB Water Distilled X 2 2 X X 2 2 A A TEVNB Water Sea X A A TEVNB Whiskey X X A TEVNB Wine X 2 2 X 2 X A TEVNB Xylene A X TV Zinc Chloride X X X X X 2 A A TEVNB Zinc Nitrate 2 2 X A TEVNB Zinc Sulfate 0% X 2 2 X 2 X A TEVNB Ratings given are based at 70 F. Legend Metal: Excellent; 2 Good; Fair; X Not Recommended; and Contact Factory Legend Non-Metal: A Acceptable; X Not Recommended; and Contact Factory Legend Gasket/Seal Material: T Teflon; V Viton; E EPDM; N Neoprene; and B Buna N 79

180 FAX: INDUSTRIAL TECHNICAL DATA Steam Temperature/Pressure Conversion Guide Temperature/Pressure Equivalents of Saturated Steam Gauge Pressure at Sea Level F C Lbs/In 2 F C Lbs/In 2 F C Lbs/In Degrees Celsius = /9 (Degrees Fahrenheit 2) 80

181 FAX: INDUSTRIAL TECHNICAL DATA Temperature Conversions Look up reading in middle column. If in degrees Centigrade, read Fahrenheit equivalent in right hand column; if in Fahrenheit degrees, read Centigrade equivalent in left hand column. C F/ C F C F/ C F C F/ C F

182 FAX: INDUSTRIAL TECHNICAL DATA Fraction/Decimal Conversion Chart Inches Millimeters Inches Millimeters

183 HYDRAULIC HOSE FITTINGS AND ADAPTERS Hydraulic Hose Interchange (Showing Gates Hose Type with corresponding Competitor s Hose Type) The information provided below is intended as a reference guide only. These hoses are similar but are not identical in all respects. Refer to Gates Hose, Fittings & Equipment Catalog, pages 89-2 to assure that the suggested hose will handle the required application, and for correct Gates couplings to be used with hose selected. IMPERIAL PARKER GATES AEROQUIP DAYCO GOODYEAR EASTMAN HANNIFIN STRATOFLEX WEATHERHEAD G6K HT6 N4 C FC27 NH/CMH 90/9 N/N6 74/76 240/4240/276 H470 G4K/GK FC24 N/CN N4/N /4240 C2 FC20A/FC6 CE/CZ 920/92 M6/M7 77C 270 H40 GS4 FC20A CE/CZ 920 M7 77C 270 H40 G2AT-HMP FC9 NJ M2T FC0/FC40 FX 9292 HR2C/HFS2 4 C2AT FC22/279 BX 902 J4 0/ H42 C2ATH FC9/FC0 J9 C2A 09 B 9020 H /222 H02 J2AT MK AX 929 HRC/HFS 48 28/22 H00 MK -0, -2, -6 FC22/279/08 BX/QX 902/909 J4/L 0/782/4 244 H42 CT FC2/266 MX 90 E7 42/78 28/22 H04 CTH E9 42HT CA FC98/FC298 M 900 D7 4/77 2/22 H008 CC 0 D 900 Y9A 78/20/27 2/22 H066/H069 CR 26 F H69 CE FC /286/2 CD FC24/FC0/FC G 286/266 H448 C 28 H 900 D H07 CH ZD C6 A 9060 A 77 H009 C6H A H409 C4 FC8 C 9040 U 88/90 29 H09 G4H U2 RLA L R RLC LOC 2 L C 82/8 22 H00 LOL Plus 26/28/27 L 9240/920/926 B7/B8/HPO/HAW 80/GPH 20/29 H0/H20 C7S FC426/FC70 R7/R HR7/DA 40N H46/H446 FC72 R70 HR7H/K4/K 0H H4/H44 C7SNC FC427/FC7 R HR70/D4A/L4/L 0A/8A FC7 8H C8S FC74 R8/R HR8 20N/80N C8SNC FC7 R HR80 28N/88N C TS T H24 PolarSeal FC P-80/769 H747 M2T is a registered trademark of The Gates Rubber Company. 8

184 84 HYDRAULIC HOSE FITTINGS AND ADAPTERS How To Identify Gates Hydraulic Components Gates Hydraulic Descriptions Descriptions for Gates Hydraulic Hose, Couplings, and Adapters were designed to simplify the identification of Gates hydraulic products. Hose and coupling descriptions are an effective reference when determining Gates hydraulic part numbers. Hydraulic hose catalog descriptions are the simplest we could devise. The letters are abbreviations of a complete description and are all easy to learn. For SAE hoses the basic letter is C and it is a substitute for 00. The number which follows the C designates the SAE specification. (Example: CA means SAE 00RA; we dropped the R to keep the descriptions short.) Additional hoses have descriptions which are abbreviations of their construction or use. For a detailed listing of Gates Hydraulic Hose Catalog Descriptions, refer to Hydraulic Hose Selection Guide (Pages 84 and 8). This chart shows: Standard Industry Specifications (if applicable) Tube & Cover Stock Hose Description Temperature Range Construction Dash Size Use Hose Page Number NOTE: SAE 00R series hose listed in this catalog meet or exceed those specifications as described in SAE J7. In applications where the electrical conductivity of a hydraulic assembly is a factor, Gates C7SNC and C8SNC hose is non-conductive per SAE J7 as tested per SAE J4. CAUTION: Working Pressure Working pressure of the application should always determine selection of hose. Used up to the recommended working pressure, hose will provide normal service life before replacement is required. Maximum Working Pressure Maximum working pressure of any hose line must also include any spikes or pressure surges. This may require a gauge reading since pressure relief valve settings can be initially overridden. Minimum Burst Pressure When new, the hose described in this catalog will meet or exceed the minimum burst pressure shown in the hose specification tables. However as with any hose in the industry after hose has been impulsed for a length of time, the minimum burst pressure will decrease from the figure shown in the specification tables. Temperature Ranges The temperature ranges specified for specific hoses refer to recommended limits of fluids being conveyed or ambient temperatures. Exceeding these limits will cause degradation of material compounds and reduced hose service life. 7 Easy Steps To Selecting The Proper Hose An effective way to remember hose selection criteria is to remember the word... S T A M P E D S = Size T = Temperature A = Application M = Material to be conveyed P = Pressure E = Ends or couplings D = Delivery (volume and velocity). Hose Size (Dash Numbers) The inside diameter of the hose must be adequate to keep pressure loss to a minimum and avoid damage to the hose due to heat generation or excessive turbulence. See Nomograph Chart in Hydraulic Technical Data on page 67. To determine the replacement hose size, read the layline printing on the side of the original hose. If the original hose layline is painted over or worn off, the original hose must be cut and inside diameter measured for size. NOTE: Before cutting an original hose assembly, measure the overall assembly length. This measurement will be required to build the replacement assembly. The hydraulics industry has adopted a measuring system called Dash Numbers to indicate hose and coupling size. The number which precedes the hose or coupling description is the dash size (see following table). This industry standard number denotes hose I.D. in sixteenths of an inch. (The exception to this is the SAE00R hoses CC, CD, CE, CR, C4 and Refrigeration/AC, where dash sizes denote hose I.D. equal to equivalent tube O.D.) Hose O.D. can be a critical factor when hose routing clamps are used or hoses are routed through bulkheads. Check individual hose specification tables for O.D.s.

185 HYDRAULIC HOSE FITTINGS AND ADAPTERS Selecting The Proper Hose continued Dash Numbers Hose I.D. (Inches) Dash All Except C Series, C4 and PolarSeal C Series, C4 and PolarSeal No. Inches Millimeters Inches Millimeters / Temperature When selecting a replacement assembly, two areas of temperature must be considered. These are fluid temperature and ambient temperature. The hose selected must be capable of withstanding the minimum and maximum temperature seen by the system. Care must be taken when routing near hot manifolds and in extreme cases a heat shield may be advisable. See the Gates Hydraulic Hose Selection Guide on pages 86 and 87, Hose Specification Pages, and/or the Additional Temperature Limits for Gates Hydraulic Hose Chart from Gates Hydraulic Hose, Fittings & Equipment Catalog for temperature ranges and limits for water, water/oil emulsions and water/glycol solutions.. Application Determine where or how the replacement hose or assembly is to be used. Most often only a duplicate of the original hose will have to be made. To fulfill the requirements of the application, additional questions may need to be answered, such as: Where will hose be used? Fluid and/or Ambient Temperature? Hose Construction? Equipment Type? Fluid Compatibility? Thread End Connection Type? Working and Surge Pressures? Environmental Conditions? Permanent or Reusable Couplings? Suction Application? Routing Requirements? Thread Type? Government and Industry Standards Unusual Mechanical Loads? Minimum Bend Radius? Being Met? Non-Conductive Hose Required? Excessive Abrasion? 4. Material to be Conveyed Some applications require specialized oils or chemicals to be conveyed through the system. Hose selection must assure compatibility of the hose tube, cover, couplings and O-rings with the fluid used. Additional caution must be exercised in hose selection for gaseous applications such as refrigerant and LPG. NOTE: All block type couplings contain nitrile O-rings which must be compatible with the fluids being used.. Pressure Most important in the hose selection process is knowing system pressure, including pressure spikes. Published working pressures must be equal to or greater than the system pressure. Pressure spikes greater than the published working pressure will shorten hose life and must be taken into consideration. Gates DOES NOT recommend using hoses on applications having pressure spikes greater than published working pressures of the hose. 6. Ends of Couplings Identify end connections using Gates coupling templates and measuring tools in Hydraulic Technical Data on pages 6 and 64, or Coupling Identification section pages 204 through 207. Once thread ends have been identified, consult the appropriate section of the catalog for specific catalog description selection. 7. Delivery (Vacuum and Velocity) If the same I.D. of the original hose is used, assume the system is properly sized to efficiently transport fluid. If the system is new or altered, determine the hose I.D. needed to transport required fluid volume flow by using the Nomographic Chart in Hydraulic Technical Data on page 67. 8

186 HYDRAULIC HOSE FITTINGS AND ADAPTERS Gates Hydraulic Hose Selection Guide Stock Standard Industry Descrip- Construction Tube Cover Specification tion (Reinforcement) Use Name Type Name Type SAE 00R G6K 4&6-spiral, wire Extremely High Pressure Neoprene A Neoprene A SAE 00R C 4&6-spiral, wire High Pressure Petrol, Oils Neoprene A Neoprene A G4K/GK 4-spiral, wire High Pressure Petrol, Oils Neoprene A Neoprene A SAE 00R2 C2 4-spiral, wire High Pressure Petrol, Oils Neoprene A Neoprene A C2M 4-spiral, wire High Pressure, Tight Bends Neoprene A Neoprene A GS4 4-spiral, wire High Pressure Petrol, Oils Neoprene EPDM SAE 00R2 Type AT G2AT-HMP 2-braid, wire Multi-Fluid, High Temperature CPE J Neoprene A SAE 00R6 M2T 2-braid, wire Tight Bends, High Flexibility Nitrile C NBR/PVC C 2 SAE 00R2 Type AT, DIN Type 2SN C2AT 2-braid, wire Petroleum Oils Nitrile C NBR/PVC C 2 SAE 00R2 Type AT C2ATH 2-braid, wire High Temperature Nitrile C Hypalon M SAE 00R2 Type A, DIN Type 2ST C2A 2-braid, wire Petroleum Oils Nitrile C NBR/PVC C 2 PCII 2-braid, wire Pressure Wash Nitrile C NBR/PVC C 2 NCB 74, DIN Type 2ST CPB 2-braid, wire Mine Roof-support systems Nitrile C NBR/PVC C 2 BCS 74, DIN Type 2ST CPB+ 2-braid, wire Mine Roof-support systems *** NBR/PVC C 2 IJ00 J2AT 2-braid, wire Industrial Jack Hose *** NBR/PVC C 2 SAE 00R7 MK &2-braid, wire, 4 4-spiral Tight Bends, High Flexibility Nitrile C NBR/PVC C 2 SAE 00R Type AT, DIN Type SN CT -braid, wire Petroleum Oils Synthetic Elastomer C NBR/PVC C 2 SAE 00R Type AT CTH -braid, wire High Temperature Nitrile C Hypalon M SAE 00R Type A, DIN Type ST CA -braid, wire Petroleum Oils Synthetic Elastomer C NBR/PVC C 2 PCI -braid, wire Pressure Wash Nitrile C NBR/PVC C 2 SAE J402, DOT FMVSS06-74, Type AII CD -braid, T-W-T Petrol. & Syn. fluids, air brakes CPE J Textile SAE 00R, DOT FMVSS06-74, Type AII *CC* -braid, T-W-T Petr. Oil, Air Brake, Power Steering *Nitrile* C Textile CR -braid, T-W-T Petr. Oil, Air, Water Nitrile C Neoprene A DOT FMVSS06-74, Type AI CE -braid, T-W-T Air Brake, Power Steering, Lube Nitrile C Textile SAE 00R C 2-braid, Textile Petrol. Oils, Antifreeze, Water Nitrile C Neoprene A CH 2-braid, Textile High Temperature Nitrile C Neoprene A SAE 00R6 C6 -braid, Textile Petrol. Oils, Antifreeze Nitrile C Neoprene A SAE 00R6 C6H -braid, Textile High Temperature Nitrile C Neoprene A SAE 00R4 C4 2-braid, Textile, helical wire Return & Suction Nitrile C Neoprene A SAE 00R4 G4H 2-spiral, Textile, helical wire Return & Suction High Temperature Nitrile C Neoprene A RLA -braid, Textile Return & Low Pressure Nitrile C Neoprene A RLC -braid, Textile Return & Low Pressure Nitrile C Neoprene A LOC -braid, Textile Petrol., Oils, Antifreeze, Water Nitrile C Neoprene A LOL+ -braid, Textile Diesel Fuel & Air Nitrile C Neoprene A Thermoplastic SAE 00R7 C7S -braid, polyester Petroleum & Synthetic Fluids Nylon Z Urethane U SAE 00R7 C7SNC -braid, polyester Non-conductive Nylon Z Urethane U SAE 00R8 C8S -braid, Kevlar Petroleum & Synthetic Fluids Nylon Z Urethane U SAE 00R8 C8SNC -braid, Kevlar Non-conductive Nylon Z Urethane U Refrigerant SAE J Type AII Dimensions/ Type D Performance AC4a 2-spiral, textile Air Conditioning (R2 and R4a) Chloroprene A EPDM P Teflon SAE 00R4 C4 -braid, stainless steel High Temperature, Multi-Fluid PTFE Stainless Steel * -4 and - sizes have a Neoprene tube. M2T is a registered trademark of The Gates Rubber Company. *** Nitrile or Neoprene 86

187 HYDRAULIC HOSE FITTINGS AND ADAPTERS Gates Hydraulic Hose Selection Guide continued Temp. Dash Size vs. Rated Working Pressure (psi) Industry ( F) ,000 6,000 6,000 6, ,000,000,000,000,000, ,000,000, ,000 4,000 4,000 4,000,000 2,00 2, ,000 4,000, ,000 4,000 4,000,000 2,00 2, ,20,00,000 2, ,000 4,000,00 2,70 2,20 2, ,000,800 4,800 4,000,62,00 2,400, ,62,20, ,000,000,07 4,000,00 2,70 2,20 2,000,62,00, ,00 4,00, ,0 7,700 6,80 4,90,770 2, ,00 9,2 6,400 4,90,77 2, ,000 0, ,000,000,000,000,000,000, ,62,27,2 2,600 2,2,900,2, ,70 2,20 2,000,00,20, ,27 2,00 2,600 2,2,900,2, ,000,000 2, ,00,00,00,20, ,000,000 2,20 2,000,70, ,000,000 2,20 2,000,70, ,00,00,00,20, ,00,20,200,2, ,20,2, ,000 2,70 2,00 2,20 2,000,20, ,000 2,70 2,00 2,20 2,000,20, ,000,000 4,000,00 2, ,000 4,000, ,00,00,00, Static pressures for mine application All purpose fleet application service 40 F to +00 F ( 40 C to +49 C). 87

188 HYDRAULIC HOSE FITTINGS AND ADAPTERS Agency Specifications and Hose Selection Guide INDUSTRY AGENCIES SAE Society of Automotive Engineers DNV Det Norske Veritas for North Sea Floating Vessels RCCC Regular Common Carrier Conference for Fleet RCCC Truck and Bus DIN Deutsche Industrial Norme, German NCB-74 National Coal Board, British IJS Industrial Jack Specifications GOVERNMENT AGENCIES MSHA U.S. Mine Safety and Health Administration DOT/FMVSS U.S. Department of Transportation/Federal DOT/FMVSS Motor Vehicle Safety Standard USCG U.S. Coast Guard. Follow SAE J942/ for USCG approved USCG hoses for commercial applications only. Use SAE J27 USCG hoses for fuel applications on pleasure craft. MIL/DOD U.S. Military Department of Defense Meets These Agency Specifications Hose DOT/ USCG Type SAE DNV RCCC DIN NCB-74 IJS MSHA FMVSS Fuel Power G6K C 00R 2 C2 00R SP C2M GK 00R G4K 00R GS4 CPS SP# LW SP# CPB ST# CPB ST# G2AT-HMP 00R2 Type AT M2T 00R6 C2AT 00R2 Type AT SN# C2ATH 00R2 Type AT 7 C2A 00R2 Type A ST# J2AT MK MK -0, -2, -6 CT 00R Type AT ST# CTH 00R Type AT 4 CA 00R Type A ST# CC 00R RP0(B) Type AII CR 00R CE J Type AI CD J Type AII C 00R CH 00R C6 00R6 C6H 00R6 C4 00R4 G4H 00R4 6 FLH 0R2 Type LOL Plus (Black only) THERMOPLASTIC C8S, C8SNC 00R8 C7S, C7SNC 00R7 C4 00R4 FREON AC4A J, J2064 # As noted on the respective catalog page in the hose section. M2T is a registered trademark of The Gates Rubber Company. Only 2 Except 8 Except 6 & 6 4 Except 4, 2, 2 Except 2 & 2 6 Except 4 7 Except 4 88

189 CT -Wire Braid Hose SAE 00R Type AT Recommended for: Medium pressure hydraulic lines. Meets or exceeds the requirements of SAE 00RAT and performance requirements of DIN SN. Tube: Black, oil-resistant synthetic rubber. (Nitrile). Reinforcement: One braid of high-tensile steel wire. Cover: Black, oil- and abrasion-resistant synthetic rubber. (Modified Nitrile). No skiving needed with Type T, Power Crimp or MegaCrimp couplings. Temperature range: -40 F to +22 F (-40 C to +00 C). SPECIFICATIONS Hose Hose Working Working Min. Min. Min. Catalog Product I.D. O.D. Pressure Pressure Burst Pressure Burst Pressure Bend Radius Description No. (In.) (In.) (psi) (bar) (psi) (bar) (In.) CT , ,00,000. 4CT ,27 22, CT ,2 2 2, CT , , CT ,2 60 9, CT , , CT ,2 0 6, CT ,27 88, CT , Power Crimp and MegaCrimp are registered trademarks of The Gates Rubber Company. HYDRAULIC HOSE FITTINGS AND ADAPTERS CTH High Temp -Wire Braid Hose SAE 00R Type AT Recommended for: Medium pressure hydraulic oil lines. Meets or exceeds requirements of SAE 00R Type AT. Tube: Black, oil-resistant, synthetic rubber. (Nitrile). Reinforcement: One braid of high tensile steel wire. Cover: Black, oil- and abrasion-resistant synthetic rubber. (Hypalon ). Temperature range: -40 F to +27 F (-40 C to + C) constant and 00 F (49 C) intermittent (up to 0% of operating time). SPECIFICATIONS Min. Min. Hose Hose Working Burst Bend Catalog Product I.D. O.D. Pressure Pressure Radius Description No. (In.) (In.) (psi) (psi) (In.) 4CTH ,70, CTH ,20 9,000. 8CTH ,000 8, CTH ,00 6, CTH ,20, CTH ,000 4, CTH , CTH , CTH , Hypalon is a registered trademark of the DuPont Co. 89

190 HYDRAULIC HOSE FITTINGS AND ADAPTERS C2AT 2-Wire Braid Hose SAE 00R2 Type AT (Meets Flame Resistance Acceptance Designation U.S. MSHA 2G ) Recommended for: High pressure hydraulic oil lines. Meets or exceeds the requirements of SAE 00R2AT and performance requirements of DIN SN. Tube: Black, oil-resistant synthetic rubber. (Nitrile). Reinforcement: Two braids of high-tensile steel wire. Cover: Black, oil- and abrasion-resistant thin synthetic rubber. No skiving required with Type T or Power Crimp couplings. (Modified Nitrile). Temperature range: -40 F to +22 F (-40 C to +00 C). SPECIFICATIONS Hose Hose Working Working Min. Min. Min. Catalog Product I.D. O.D. Pressure Pressure Burst Pressure Burst Pressure Bend Radius Description No. (In.) (In.) (psi) (bar) (psi) (bar) (In.) C2AT , ,000,60. 4C2AT , ,200, C2AT , ,200,20. 8C2AT , ,000, C2AT , ,00, C2AT ,00 2 2, C2AT , , C2AT ,82 2 7, Power Crimp is a registered trademark of The Gates Rubber Company. C2ATH High-Temp 2-Wire Braid Hose SAE 00R2 Type AT (Meets Flame Resistance Acceptance Designation U.S. MSHA 2G ) Recommended for: High pressure hydraulic oil lines. Meets or exceeds the requirements of SAE 00R2AT. Tube: Black, oil-resistant synthetic rubber. (Hypalon ). Reinforcement: Two braids of high-tensile steel wire. Cover: Black, oil-resistant synthetic rubber. (Hypalon ). Temperature range: -40 F to +27 F (-40 C to + C) constant and 00 F (49 C) intermittent up to 0% of operating time. SPECIFICATIONS Min. Min. Hose Hose Working Burst Bend Catalog Product I.D. O.D. Pressure Pressure Radius Description No. (In.) (In.) (psi) (psi) (In.) 20C2ATH ,62 6, C2ATH ,20, C2ATH ,2 4,00 2. Hypalon is a registered trademark of the DuPont Co. 90

191 HYDRAULIC HOSE FITTINGS AND ADAPTERS MK Mega000 Hose (Meets Flame Resistance Acceptance Designation U.S. MSHA 2G ) SPECIFICATIONS Min. Min. Hose Hose Working Burst Bend Catalog Product I.D. O.D. Pressure Pressure Radius Description No. (In.) (In.) (psi) (psi) (In.) 4MK ,000 2, MK ,000 2, MK ,000 2, MK ,000 2, MK ,000 2, MK ,000 2, MK ,000 2, MegaTuff HOSE SPECIFICATIONS Min. Min. Hose Hose Working Burst Bend Catalog Product I.D. O.D. Pressure Pressure Radius Description No. (In.) (In.) (psi) (psi) (In.) 0MK-MTF ,000 2, MK-MTF ,000 2, MK-MTF ,000 2, MK Mega000 and MegaTuff are registered trademarks of The Gates Rubber Company. Recommended for: High pressure hydraulic oil lines. Exceeds SAE performance requirements because MK hose has smaller exterior dimensions and significantly tighter bend radius up to half SAE rating. Tube: Black, oil-resistant, synthetic rubber. (Nitrile). Reinforcement: Braided high tensile steel wire. Cover: Black, oil-, abrasion- and weather-resistant, synthetic rubber. (Modified Nitrile). Temperature range: -40 F to +22 F (-40 C to +00 C). C7S and C7SNC Hydraulic Hose SAE 00R7 SPECIFICATIONS C7S Min. Min. Hose Hose Working Burst Bend Catalog Product I.D. O.D. Pressure Pressure Radius Description No. (In.) (In.) (psi) (psi) (In.) 2C7S ,00 0,000. C7S ,000 2, C7S ,70,000. C7S ,00 0, C7S ,20 9, C7S ,000 8,000. 2C7S ,20,000. 6C7S ,000 4, SPECIFICATIONS C7SNC Min. Min. Hose Hose Working Burst Bend Catalog Product I.D. O.D. Pressure Pressure Radius Description No. (In.) (In.) (psi) (psi) (In.) 2C7SNC ,00 0,000. C7SNC ,000 2, C7SNC ,70,000. C7SNC ,00 0, C7SNC ,20 9, C7SNC ,000 8,000. 2C7SNC ,20,000. 6C7SNC ,000 4, Recommended for: Petroleum, water base and synthetic hydraulic fluids. Applications include power and telephone mobile equipment (cherry pickers), lubrication lines, blowout preventer control lines, hydraulic lifts and farm and construction machinery. Orange color C7SNC meets SAE 00R7 nonconductivity requirements. Both C7S and C7SNC hoses meet or exceed performance requirements of SAE 00R7 with significantly tighter bend radius. Tube: 00% seamless nylon that easily handles a broad range of hydraulic fluids, including phosphate esters and water glycol. Reinforcement: Single polyester braid. Cover: Black or orange urethane that resists hydraulic fluids, high temperatures, aging and weathering. Orange C7SNC is non-perforated for applications requiring electrical non-conductivity. Meets SAE 00R7 Electrical Conductivity Test. Maximum leakage shall not exceed 0 microamperes when subjected to 7kV/Ft. for five minutes. (Orange is industry accepted color for non-conductive hose.) Black C7S is perforated for use in general hydraulic and pneumatic service. Temperature range: -6 F to +200 F (-4 C to +9 C) continuous service for petroleum and synthetic oils. Maximum of 8 F (70 C) for water, water/oil emulsions and water glycol. 9

192 HYDRAULIC HOSE FITTINGS AND ADAPTERS G4H MegaVac Return Line and Suction Hose (Meets Flame Resistance Acceptance Designation U.S. MSHA 2G ) Recommended for: Petroleum and water-base hydraulic fluids in suction lines or in low pressure return lines. One-half the bend radius of SAE 00R4. Tube: Black, synthetic nitrile rubber is specifically designed for resistance to high temperatures. Reinforcement: Double spiral reinforced with a helical spiral-wire to prevent collapse. Cover: Black neoprene synthetic rubber is oil- and abrasion-resistant. Temperature range: -40 F to +27 F (-40 C to + C) constant and 00 F (49 C) intermittent (up to 0% of operating time). SPECIFICATIONS Min. Min. Hose Hose Working Burst Bend Catalog Product I.D. O.D. Vacuum Pressure Pressure Radius Description No. (In.) (In.) (In. Hg) (psi) (psi) (In.) 2G4H , G4H , G4H , G4H ,60. 2G4H , G4H , G4H , G4H , G4H ,22 2. G4H MegaVac is a registered trademark of The Gates Rubber Company. C2M MegaSpiral Hose SAE 00R2 (Meets Flame Resistance Acceptance Designation U.S. MSHA 2G ) Also available with abrasion-resistant MegaTuff cover. Recommended for: Very high pressure hydraulic applications. Provides excellent impulse life; all sizes surpass,000,000 impulse cycles when tested at 20 F (2 C) at one-half the minimum bend radius specified by SAE 00R2, and at % of rated working pressure. Half the bend radius and more flexible than SAE 00R2. Tube: Black, oil-resistant, synthetic rubber. (Neoprene). Reinforcement: Four layers of alternated, spiraled high tensile steel wire over a layer of fabric. Cover: Black, oil-resistant, synthetic rubber. (Neoprene). Temperature range: -40 F to +20 F (40 C to +2 C). Available in 2 to 200 continuous lengths. SPECIFICATIONS Min. Min. Hose Hose Working Burst Bend Catalog Product I.D. O.D. Pressure Pressure Radius Description No. (In.) (In.) (psi) (psi) (In.) 2C2M ,000 6, C2M ,000 6, C2M ,000 2, C2M MegaSpira and MegaTuff are registered trademarks of The Gates Rubber Company. 92

193 HYDRAULIC HOSE FITTINGS AND ADAPTERS C Spiral Wire Hose SAE 00R (Meets Flame Resistance Acceptance Designation U.S. MSHA 2G ) Recommended for: Extremely high pressure hydraulic applications, and severe applications such as hydrostatic transmissions. C is designed to meet all requirements of SAE 00R specifications. Tube: Black, oil-resistant synthetic rubber. (Neoprene). Reinforcement: Four layers of alternated, spiraled, high tensile steel wire over a layer of fabric on 0, 2 and 6 sizes six layers of alternated spiraled, high tensile steel wire over a layer of fabric on 20, 24, and 2 sizes. Cover: Black, oil-resistant synthetic rubber. (Neoprene). Red stripe. Temperature range: -40 F to +20 F (-40 C to +2 C). Available in 2 to 200 continuous lengths. Skiving Required SPECIFICATIONS Min. Min. Hose Hose Working Burst Bend Catalog Product I.D. O.D. Pressure Pressure Radius Description No. (In.) (In.) (psi) (psi) (In.) 0C ,000 20, C ,000 20, C ,000 20, C ,000 20, C ,000 20, C ,000 20, MegaTuff HOSE SPECIFICATIONS Min. Min. Hose Hose Working Burst Bend Catalog Product I.D. O.D. Pressure Pressure Radius Description No. (In.) (In.) (psi) (psi) (In.) 0C-MTF ,000 20, C-MTF ,000 20, C-MTF ,000 20, C-MTF ,000 20, C-MTF ,000 20, C-MTF ,000 20, MegaTuff is a registered trademark of The Gates Rubber Company. 9

194 EXTREMELY HIGH PRESSURE G6K Hose 94 HYDRAULIC HOSE FITTINGS AND ADAPTERS Recommended for extremely high pressure and high impulse hydraulic applications. Designed for hydrostatic transmissions and other severe operating conditions psi working pressure. Meets U.S. MSHA 2G Flame Resistance Acceptance Designation. Four or six layers of spiraled high tensile steel wire over a fabric layer. Available in 8, 2, and 4 I.D. No internal tube skive required, reducing chance of system contamination. Highly visible layline for easy identification. Low profile ferrules make plumbing easy in tight areas. Variety of PCM coupling configurations make factory-quality assemblies easy. and 4 I.D. available in 2 to 200 continuous lengths. Abrasion resistant MegaTuff cover available on this hose. EXTREMELY HIGH PRESSURE G4K Hose, SAE 00R Recommended for extremely high pressure and high impulse hydraulic applications psi working pressure. Available only in 4 I.D. Exceeds SAE 00R in temperature rating and impulse life. Four layers of spiraled high tensile steel wire over a fabric layer. Variety of no-skive PCS coupling configurations make assembly fabrication easy. Available in 2 to 200 continuous lengths. Abrasion resistant MegaTuff cover available on this hose. EXTREMELY HIGH PRESSURE GK Hose, SAE 00R Recommended for extremely high pressure and high impulse hydraulic applications. 000 psi working pressure. Available in 2 and 2 I.D. Exceeds SAE 00R in temperature rating and impulse life. Four layers of spiraled high tensile steel wire over a fabric layer. Variety of no-skive PCS coupling configurations make assembly fabrication easy. Available in 2 to 200 continuous lengths. Abrasion resistant MegaTuff cover available on this hose. EXTREMELY HIGH PRESSURE C Hose, SAE 00R Hose Data page 9 MegaTuff is a registered trademark of The Gates Rubber Co. Gates Hydraulic Hose Features Recommended for extremely high pressure and high impulse hydraulic applications. Designed for hydrostatic transmissions and other severe operating conditions. 000 psi working pressure. Meets or exceeds SAE 00R. Meets U.S. MSHA 2G Flame Resistance Acceptance Designation. Four or six alternating layers of spiraled high tensile steel wire over fabric layer. Available in 8 through 2 I.D. No internal tube skive, reducing chance of system contamination. Highly visible layline for easy identification. Low profile ferrules make plumbing convenient in tight areas. Variety of PCM coupling configurations make factory-quality assemblies easy. All sizes available in 2 to 200 continuous lengths. Abrasion resistant MegaTuff cover available on this hose. See page 9. Ask for a Gates Hydraulic Hose, Fittings & Equipment Catalog for further information.

195 HYDRAULIC HOSE FITTINGS AND ADAPTERS Gates Hydraulic Hose Features continued VERY HIGH PRESSURE C2M MegaSpiral Hose, SAE 00R2 Recommended for very high pressure hydraulic applications. Provides excellent impulse life, surpassing million impulse cycles when tested under SAE 00R2 conditions. 000 to 4000 psi working pressure. Half the bend radius and more flexible than SAE 00R2. Meets or exceeds SAE 00R2. Available in 8, 2, 4, and 4 I.D. sizes. Four alternating layers of spiraled high tensile steel wire over fabric layer. Highly visible layline printing for easy and permanent identification. Abrasion-resistant synthetic rubber cover. No-skive ferrules for PCS couplings make assembly fabrication easy. All sizes available in 2 to 200 continuous lengths. Abrasion resistant MegaTuff cover available on this hose. See page 90. LOW PRESSURE G4H MegaVac Hose, SAE 00R4 Recommended for petroleum and water base hydraulic fluids in suction lines or in low pressure return lines. 6 to 20 psi working pressure. One-half the bend radius of SAE 00R4. Flexible and lightweight. Double spiral reinforced with helical spiral-wire to prevent collapse. Available in 4 through 4 I.D. Permanent PC and C4 style couplings make assemblies easy. LOW PRESSURE C4 Hose, SAE 00R4 Recommended for petroleum and water base hydraulic fluids in suction lines or in low pressure return lines. 0 to 00 psi working pressure. Meets or exceeds SAE 00R4. Braided fiber reinforcement with spiral wire to prevent collapsing. Available in 4 through I.D. Permanent C4 style couplings make assemblies easy. LOW PRESSURE LOL PLUS Hose Recommended for petroleum base hydraulic oils, water, hot lubricating oils, diesel fuels and air. 00 psi working pressure. One fiber braid reinforcement. Available in 6 through 4 I.D. Lock-on reusable couplings make assemblies easy. NOTE: LOL Plus Hose is available in seven colors: black, blue, green, NOTE: red, yellow, gray and white. Hose Data page 92 Hose Data page 92 REFRIGERANT PolarSeal Hose, SAE J Recommended for transportation refrigeration and air conditioning systems that carry liquid and gaseous R4a and R2 refrigerants. 00 psi working pressure. Meets or exceeds SAE J, Type A2 dimensions; SAE J, Type D performance. Spiraled polyester reinforcement. Available in 6 through 8 I.D. Permanent ACA couplings make assemblies easy. MegaSpiral, MegaTuff, MegaVac are registered trademarks and PolarSeal is a trademark of The Gates Rubber Company. Ask for a Gates Hydraulic Hose, Fittings & Equipment Catalog for further information. 9

196 HYDRAULIC HOSE FITTINGS AND ADAPTERS Gates Hydraulic Hose Features continued MEDIUM PRESSURE CC Hose, SAE 00R and J402 Recommended for medium pressure hydraulic petroleum base oil lines in numerous applications. Meets or exceeds SAE 00R, SAE J402 Type AII and DOT FMVSS Type AII. 0 to 000 psi working pressure. One braid high tensile carbon steel wire over polyester braid. Textile braid cover. Available in 6 through 2 8 I.D. C type field attachable and permanent (through -2 size) couplings available. MEDIUM PRESSURE CE Hose, SAE J09 Recommended for air brake hose, power steering, fuel filter, engine and transmission coolant lines and hot 00 F (49 C) lube lines. Recommended for diesel engine flexline applications. Meets DOT FMVSS Type A and SAE J09 hot oil circulation test. 00 to 00 psi working pressure. Single braid of high tensile steel wire over polyester braid. Textile braid impregnated with rubber on black cover. Available in 6 through 8 I.D. CE type field attachable and permanent couplings available. HIGH PRESSURE M2T Megaflex Hose, SAE 00R2 Recommended for high pressure hydraulic oil lines. One-half SAE 00R2 bend radius to 000 psi working pressure. Meets U.S. MSHA 2G Flame Resistance Acceptance Designation. Two braids of high tensile steel wire. Available in 4 through I.D. Superior flex impulse performance and lightweight. Easy to route and installs quickly in tight areas. No skiving required. Wide variety of Power Crimp and MegaCrimp Couplings available. Abrasion resistant MegaTuff cover available on this hose. HIGH PRESSURE C2AT Hose WITH DIN RATING, SAE 00R2 Hose Data page 90 Recommended for high pressure hydraulic oil lines. Meets performance requirements of DIN SN 2 to 4 bar working pressure. Meets or exceeds SAE 00R2AT 82 to 6000 psi working pressure. Meets U.S. MSHA 2G Flame Resistance Acceptance Designation. Two braids of high tensile steel wire. Available in 6 through 4 I.D. No skiving required. Power Crimp, MegaCrimp and field attachable couplings available. MegaCrimp, M2T, Megaflex, MegaTuff and Power Crimp are registered trademarks of The Gates Rubber Company. 96 Ask for a Gates Hydraulic Hose, Fittings & Equipment Catalog for further information.

197 HYDRAULIC HOSE FITTINGS AND ADAPTERS Gates Hydraulic Hose Features continued HIGH PRESSURE C2ATH Hose, SAE 00R2AT Recommended for high temperature, high pressure hydraulic oil lines. 7 to 62 psi working pressure. Meets or exceeds SAE 00R2AT. Meets U.S. MSHA 2G Flame Resistance Acceptance Designation. Two braids of high tensile steel wire. Available in 4, 2 and 2 I.D. No skiving required. Wide variety of Power Crimp and field attachable couplings available. HIGH PRESSURE J2AT Jack Hose, 0,000 psi Recommended for hydraulic jack applications. 0,000 psi working pressure on static applications. Two braids of high tensile steel wire. Available in 4 and 8 I.D. No skiving required. Meets Material Handling Institute Specification IJ 00 for Jack Hose. Wide variety of Power Crimp and MegaCrimp Couplings available. Abrasion resistant MegaTuff cover available on this hose. MEDIUM PRESSURE CT Hose WITH DIN RATING, SAE 00RAT Recommended for medium pressure hydraulic oil lines. Meets performance requirements of DIN SN 6 to 20 bar working pressure. Meets or exceeds SAE 00RAT 92 to 62 psi working pressure. One braid of high tensile steel wire. Available in 6 through 4 I.D. No skiving required. Wide variety of Power Crimp, MegaCrimp and field attachable couplings available. Hose Data page 90 Hose Data page 89 MEDIUM PRESSURE CTH Hose, SAE 00RAT Recommended for medium pressure, high temperature hydraulic oil lines. 600 to 270 psi working pressure. Meets or exceeds SAE 00RAT. Meets U.S. MSHA 2G Flame Resistance Acceptance Designation. One braid of high tensile steel wire. Available in 4 through 2 I.D. No skiving required. Wide variety of Power Crimp Couplings makes assemblies easy. Hose Data page 89 MEDIUM PRESSURE PCI Power Clean Pressure Washer Hose Recommended for use on hot and cold water high pressure cleaning equipment where heavy-duty service is required. Great for agricultural and mobile cleaning operations. 200 to 000 psi working pressure. One braid of high tensile steel wire reinforcement. Modified nitrile cover is specially compounded to handle pressure washer environment. Available in 4, 8 and 2 I.D. Wide variety of Power Crimp and MegaCrimp Couplings available. MegaCrimp, MegaTuff and Power Crimp are registered trademarks of The Gates Rubber Company. Ask for a Gates Hydraulic Hose, Fittings & Equipment Catalog for further information. 97

198 HYDRAULIC HOSE FITTINGS AND ADAPTERS Gates Hydraulic Hose Features continued VERY HIGH PRESSURE CPS Mine Hose VERY HIGH PRESSURE LW Mine Hose Recommended for high pressure hydraulic lines in longwall mining equipment and roof-support systems. 000 psi dynamic working pressure and 6000 to 6700 psi static. Meets performance requirements of DIN 2002/Jan. 98. Meets U.S. MSHA 2G-IC-C/ Flame Resistance Acceptance Designation. Four to six layers of alternated, spiraled high tensile steel wire over a fabric layer. Available in 4 through 2 I.D. Gates PCM Press-Lok Couplings and staple adapters make assemblies easy to install. All sizes available in 2 to 200 continuous lengths. Abrasion resistant MegaTuff cover available on this hose. Recommended for high pressure hydraulic lines in longwall mining equipment and roof-support systems psi dynamic working pressure and 000 psi static. Meets U.S. MSHA 2G-IC-C/ Flame Resistance Acceptance Designation. Four layers of alternated, spiraled high tensile steel wire over a fabric layer. Available in 4 and I.D. Superior to SAE specifications. Gates PCS Press-Lok Couplings and staple adapters make assemblies easy to install. Abrasion resistant MegaTuff cover available on this hose. HIGH PRESSURE SHR Rotary Drill Hose Recommended for mud drilling applications only. 000 psi working pressure. Four alternating layers of spiraled high tensile steel wire over a fabric braid. Available in 2 I.D. Gates PCS Couplings makes assemblies easy. Available in 2 to 200 continuous lengths. HIGH PRESSURE Power Plus G2AT-HMP Hi-Temp Hose Recommended for high pressure hydraulic applications where pressure or temperature requirements exceed SAE 00R2. Compatible with either petroleum base or fire-resistant phosphate ester fluids. 200 to 420 psi working pressure. Temperature range up to 00 F (49 C). Meets or exceeds SAE 00R2. Meets U.S. MSHA 2G Flame Resistance Acceptance Designation. Two braids of high tensile steel wire. Available in 2 through I.D. Wide variety of Power Crimp Couplings makes assemblies easy. MegaTuff, Power Crimp and Power Plus are registered trademarks and Press-Lok is a trademark of The Gates Rubber Company. 98 Ask for a Gates Hydraulic Hose, Fittings & Equipment Catalog for further information.

199 HYDRAULIC HOSE FITTINGS AND ADAPTERS Gates Hydraulic Hose Features continued HIGH PRESSURE MK Mega000 Hose, SAE 00R9 Recommended for high pressure hydraulic oil lines. Can be bent twice as tight as SAE 00R/00R2/00R9 bend radius standards. 000 psi rated working pressures all sizes. Available in 4 through 4 I.D. Sizes. 4, 8, 2 and 8 I.D. sizes meet SAE 00R2 impulse performance and exceed SAE 00R performance ratings. 4 and I.D. sizes meet SAE 00R9 and exceed SAE 00R2 impulse performance ratings. 4 I.D. size meets SAE 00R2 at one-half bend radius. Meets U.S. MSHA 2G Flame Resistance Acceptance Designation. Easy to route and install quickly in tight areas and saves on space and hose. Lightweight construction. No skiving required. Wide variety of Power Crimp and MegaCrimp Couplings available. (PCS couplings for and 4 I.D. sizes). Hose and ferrules are labeled with MK to simplify ferrule selection. Abrasion resistant MegaTuff cover available on this hose. See page 9. Hose Data page 9 THERMOPLASTIC C7S Hose (Black), SAE 00R7 Recommended for petroleum, water emulsion and synthetic hydraulic fluids. Tight minimum bend radius and excellent kink resistance. 000 to 000 psi working pressure. Meets or exceeds SAE 00R7. Single polyester braid. Available in 8 through I.D. Perforated urethane cover for hydraulic and pneumatic service. Nylon tube compatible with wide range of fluid types. Permanent PCTS swage style and MegaCrimp couplings make assemblies easy. Hose Data page 9 THERMOPLASTIC C7SNC Hose (Orange), SAE 00R7 Recommended for petroleum, water emulsion and synthetic hydraulic fluids. 000 to 000 psi working pressure. Meets or exceeds SAE 00R7. Single polyester braid. Available in 8 through I.D. Orange, non-perforated urethane cover meets SAE 00R7 Electrical Conductivity Test. Electrically non-conductive. Nylon tube compatible with wide range of fluid types. Tight minimum bend radius and excellent kink resistance. Permanent PCTS swage style and MegaCrimp couplings make assemblies easy. Hose Data page 9 MK Mega000, MegaCrimp, MegaTuff and Power Crimp are registered trademarks of The Gates Rubber Company. Ask for a Gates Hydraulic Hose, Fittings & Equipment Catalog for further information. 99

200 HYDRAULIC HOSE FITTINGS AND ADAPTERS Gates Hydraulic Hose Features continued THERMOPLASTIC C7SDL Hose (Black Dual Line), SAE 00R7 200 Recommended for petroleum, water emulsion and synthetic hydraulic fluids to 270 psi working pressure. Meets or exceeds SAE 00R7. Single polyester braid. Available in 4 through 2 I.D. Perforated urethane cover for hydraulic and pneumatic service. Excellent kink resistance. Nylon tube compatible with wide range of fluid types. Permanent PCTS swage style and MegaCrimp couplings make assemblies easy. THERMOPLASTIC C7SNCDL Hose (Orange Dual Line), SAE 00R7 THERMOPLASTIC C8S Hose (Black), SAE 00R8 Recommended for petroleum, water emulsion and synthetic hydraulic fluids. Orange, non-perforated urethane cover meets SAE 00R7 Electrical Conductivity Test to 270 psi working pressure. Meets or exceeds SAE 00R7. Single polyester braid. Available in 4, 8 and 2 I.D. Nylon tube compatible with wide range of fluid types. Permanent PCTS swage style and MegaCrimp couplings make assemblies easy. Recommended for petroleum, water emulsion and synthetic hydraulic fluids. 220 to 000 psi working pressure. Meets or exceeds SAE 00R8. Single aramid braid. Available in 6 through 4 I.D. Perforated urethane cover for general hydraulic and pneumatic service. Excellent kink resistance. Nylon tube compatible with wide range of fluid types. Extra tight minimum bend radius. Permanent PCTS swage style couplings make assemblies easy. THERMOPLASTIC C8SNC Hose (Orange), SAE 00R8 MegaCrimp is a registered trademark of The Gates Rubber Company. Recommended for petroleum, water emulsion and synthetic hydraulic fluids. 00 to 000 psi working pressure. Meets or exceeds SAE 00R8. Single aramid fiber braid. Orange non-perforated cover meets SAE 00R8 Electrical Conductive Test requirement. Electrically non-conductive. Available in 4, 8 and 2 I.D. Excellent kink resistance. Nylon tube compatible with wide range of fluid types. Extra tight minimum bend radius. Permanent PCTS swage style couplings make assemblies easy. NOTE: For C8S and C8SNC dual line hoses, contact Summers NOTE: Rubber Company. Ask for a Gates Hydraulic Hose, Fittings & Equipment Catalog for further information.

201 HYDRAULIC HOSE FITTINGS AND ADAPTERS How to Order Gates Hydraulic Hose Assemblies When you order hydraulic assemblies, be sure the following information is included as shown in illustrations below:. Quantity of assemblies required. 2. Hose Catalog Description (dash size and type).. First coupling dash size and end style. 4. Second coupling dash size and end style.. Offset angle or orientation of couplings must be specified if both couplings contain bent tube ends. 6. Overall assembly length (L). Caution: Rated working pressure of the application should always determine selection of hose. Used up to the recommended rated working pressure, the hose will provide normal service life before replacement is required. When new, the hose described in this catalog will meet or exceed the minimum burst pressure listed in the hose specification tables. However as with any hose in the industry after the hose has been impulsed for a length of time, minimum burst pressure will decrease from the figure shown in the specification tables. Temperature ranges specified for specific hoses refer to recommended temperature limits of fluids being conveyed or ambient temperatures. Exceeding these limits will cause degradation of material compounds and reduce hose service life. Example: Measure from centerline of flanged head to centerline of flanged head for length of assembly. Offset angle is measured with far coupling vertically downward. Orientation angle is measured clockwise. How to Make Hose Assemblies of Specific Lengths Select the hose and couplings required to make the desired hydraulic assembly. Note the cut-off measurement C for each of the couplings as listed in the specifications tables. A section is reproduced here: Assembly Overall Length Cut Hose Length C C 2 Hose Length = Assembly Overall Length Minus (C + C 2 ) Cut-off value C is the length of that part of the coupling not directly in contact with or applied to the hose. Therefore, subtract the sum of the two C values from the total length of the assembly and you will have the approximate hose length to be replaced. *Reprinted from National Hose Assemblies Manufacturers *Association NHAM-STD-2 Length Tolerances for Hydraulic Hose Assemblies and Specified Hose Lengths* Length Tolerance For lengths from 0 up to and including 2 ± 8 For lengths above 2 up to and including 8 ± 6 For lengths above 8 up to and including 6 ± 4 For lengths above 6 ±% of length measured ± to the nearest 8. 20

202 HYDRAULIC HOSE FITTINGS AND ADAPTERS Coupling Selection Gates Hydraulic Fitting Nomenclature Code Description BJ Banjo Fitting FABX Female Air Brake Swivel FBFFX Female British Standard Pipe Parallel Flat Faced Thread Swivel FBO Female Braze-on Stem FBSPPX Female British Standard Pipe Parallel Thread Swivel FBX90BL Female British Standard Pipe Parallel FDHX Female DIN Heavy Swivel FDLX Female DIN Light Swivel FFN Female Flareless Nut FFORX Female Flat-Face O-ring Swivel FFS Female Flareless Sleeve FG Female Special Grease Thread FJISX Female Japanese Industrial Standard Swivel FJX Female JIC Swivel FKX Komatsu Female Swivel FL SAE Flange Code 6 FLC Flange Caterpillar FLH SAE Flange Code 62 FLK Komatsu Flange FMX Female Mega Seal Swivel FP Female Pipe Thread FPX Female Pipe Thread Swivel FSX Female SAE Swivel FZX Parker Triple Thread HLE Hose Length Extender MB Male BOSS Thread (SAE Straight Thread) MBS Metric Bite Sleeve MBSPP Male British Standard Pipe Parallel Thread MBSPPOR Male British Standard Pipe Parallel Thread O-ring MBSPT Male British Standard Pipe Tapered Thread MBX Male BOSS Thread Swivel (SAE Straight Thread) MDH Male DIN Heavy MDL Male DIN Light MFA Male Flareless Stem Assembly MFFOR Male Flat-Face O-ring MIX Male Inverted Thread Swivel MJ Male JIC Thread MJL Male JIC Long MNH Metric Nut Heavy MNL Metric Nut Light MP Male Pipe Thread MPAPI API Male Solid MPG Male Special Grease Fitting MPLN Male Pipe Long Nose MPX Male Pipe Thread Swivel MS Male SAE Thread MSP Metric Stand Pipe Stem ORFF O-ring Flat-Face PL Press-Lok Stem PWX Pressure Washer Swivel Press-Lok is a trademark of The Gates Rubber Company. 202

203 HYDRAULIC HOSE FITTINGS AND ADAPTERS Coupling Selection continued Thread End Dash Sizes, Descriptions and Dimensions continued Coupling Dash Size and End Style Coupling Dash Size is a shorthand method of denoting the size of a particular end fitting. See Thread Size Dash Numbers Table to the right. EXAMPLE: 2MP denotes a 4 male pipe thread end fitting. The corresponding thread description for a 4 pipe thread is 4 4 NPTF solid male. EXAMPLE: 2FJX denotes a 4 female JIC swivel (7 seat) end fitting. The corresponding thread description for a 4 JIC thread is 6 2 JIC 7 flare swivel female. EXAMPLE: 2FL denotes a 4 SAE standard pressure (Code 6) flange fitting. This is the standard fitting description for a 4 SAE standard pressure flange. Thread End Catalog Descriptions Gates coupling ends shown on page 202 are accepted as industry standards. See detailed catalog listings for availability of specific hose/coupling combinations, detailed descriptions, thread end configurations such as swivels and bent tubes and special ends. Thread End Identification Tools see Hydraulic Technical Data on pages 60 and 6. Thread Size Dash Numbers Thread Size JIC (7 Flare) Dash SAE SAE O-Ring Number NPTF NPSM (4 Flare) Boss O-ring Flange dash numbers are determined by nominal flange size, or diameter of flange head which determines the O-ring size. NOTE: Refer to Hydraulic Technical Data on pages 60 and 6 for thread end identification tools and instructions available for coupling identification. Selecting The Proper Hose Dash Numbers Hose I.D. (Inches) All Except C Series, C4 C Series, C4 and PolarSeal and PolarSeal Dash No. Inches Millimeters Inches Millimeters

204 HYDRAULIC HOSE FITTINGS AND ADAPTERS Coupling/Thread Configurations MP MPAPI FMX FMX4 FMX90 FFORX90 ORFF MPLN MPX PWX MPX90 FP FPX MJ MJL FJX FJX0 FJX4 FJX60 FJX90 MS FSX FSX4 FSX90 MB MBX MBX4 MBX90 204

205 HYDRAULIC HOSE FITTINGS AND ADAPTERS Coupling/Thread Configurations continued MIX MIX4S MIX90S MFA FFS FFN FABX MPG/MPGB MFFOR FG FZX FFORX FFORX22 FFORX4 FFORX90 FKX FKX4 FKX90 FJISX MBSPT MBSPP MBSPPOR FBSPPX FBSPPX4 FL/FLK FL22 FL0 FL4/FLK4 20

206 HYDRAULIC HOSE FITTINGS AND ADAPTERS Coupling/Thread Configurations continued FL60 FL67 FL90/FLK90 FL90L FLH97 Code 6 FL00 FL0 FL20 FL2 FL Code 62 FLH Code 62 FLH22 Code 62 FLH0 Code 62 FLH4 Code 62 FLH60 Code 62 FLH90 Code 62 FLC CAT FLC22 CAT FLC0 CAT FLC4 CAT FLC60 CAT FLC67 CAT FLC90 CAT FBSPPX90 FBX90BL FBFFX MDL FDLX 206

207 HYDRAULIC HOSE FITTINGS AND ADAPTERS Coupling/Thread Configurations continued FDLX4 FDLX90 MDH FDHX FDHX4 FDHX90 MSP Metric Bite Sleeve BS HLE90 Metric Nut MHL/MNH FBO BJ HLE PL PL4 PL90 207

208 HYDRAULIC HOSE FITTINGS AND ADAPTERS Tube Fittings Standard Nut FJ-CAP Series (004) Straight Tube Union MJ-MJ Series (240) Straight Adapter Male (continued) MJ-MP Series (2404) Tube Reducer MJ-FJ Series (2406) 2FJ-CAP FJ-CAP 4FJ-CAP FJ-CAP 6FJ-CAP 8FJ-CAP 0FJ-CAP Bulkhead Nut BN Series (006) 2BN BN 4BN BN 6BN 8BN 0BN Nut TN Series (08) 2TN TN 4TN TN 6TN 8TN 0TN Sleeve SL Series (09) 2SL SL 4SL SL 6SL 8SL 0SL 2FJ-CAP 4FJ-CAP 6FJ-CAP 20FJ-CAP 24FJ-CAP 2FJ-CAP 48FJ-CAP 2BN 4BN 6BN 20BN 24BN 2BN 2TN 4TN 6TN 20TN 24TN 2TN 2SL 4SL 6SL 20SL 24SL 2SL+B80 2MJ-2MJ MJ-MJ 4MJ-2MJ 4MJ-MJ 4MJ-4MJ MJ-4MJ MJ-MJ 6MJ-4MJ 6MJ-MJ 6MJ-6MJ 8MJ-4MJ 8MJ-MJ 8MJ-6MJ 8MJ-8MJ 0MJ-4MJ 0MJ-MJ 0MJ-6MJ 0MJ-8MJ 0MJ-0MJ 2MJ-4MJ 2MJ-MJ 2MJ-6MJ 2MJ-8MJ 2MJ-MP 2MJ-2MP 2MJ-4MP MJ-2MP 4MJ-2MP 4MJ-4MP 4MJ-6MP 4MJ-8MP 4MJ-2MP MJ-2MP MJ-4MP MJ-6MP MJ-8MP 6MJ-2MP 6MJ-4MP 6MJ-6MP 6MJ-8MP 6MJ-2MP 6MJ-6MP 8MJ-2MP 8MJ-4MP 8MJ-6MP 8MJ-8MP 8MJ-2MP 8MJ-6MP 2 2MJ-0MJ 2MJ-2MJ 4MJ-2MJ 4MJ-4MJ 6MJ-6MJ 6MJ-8MJ 6MJ-0MJ 6MJ-2MJ 6MJ-4MJ 6MJ-6MJ 20MJ-2MJ 20MJ-6MJ 20MJ-20MJ 24MJ-2MJ 24MJ-6MJ 24MJ-20MJ 24MJ-24MJ 2MJ-6MJ 2MJ-20MJ 2MJ-24MJ 2MJ-2MJ 40MJ-40MJ 48MJ-48MJ Straight Adapter Male MJ-MP Series (2404) 2 0MJ-4MP 0MJ-6MP 0MJ-8MP 0MJ-2MP 0MJ-6MP 2MJ-6MP 2MJ-8MP 2MJ-2MP 2MJ-6MP 2MJ-20MP 2MJ-24MP 4MJ-8MP 4MJ-2MP 4MJ-6MP 6MJ-8MP 6MJ-2MP 6MJ-6MP 6MJ-20MP 6MJ-24MP 20MJ-2MP 20MJ-6MP 20MJ-20MP 20MJ-24MP 24MJ-6MP 24MJ-20MP 24MJ-24MP 24MJ-2MP 2MJ-6MP 2MJ-20MP 2MJ-24MP Straight Adapter Extended MJ-MP-L Series (2404-L) 2 4MJ-2MP-L 4MJ-4MP-L MJ-2MP-L MJ-4MP-L 6MJ-2MP-L 6MJ-4MP-L 6MJ-6MP-L 6MJ-8MP-L 8MJ-4MP-L 2MJ-2FP MJ-2FP MJ-4FP 4MJ-2FP 4MJ-4FP 4MJ-6FP 4MJ-8FP MJ-2FP MJ-4FP MJ-6FP MJ-8FP 6MJ-2FP 6MJ-4FP 6MJ-6FP 6MJ-8FP 6MJ-2FP 8MJ-4FP 8MJ-6FP 8MJ-8FP 8MJ-2FP 0MJ-4FP 2MJ-2MP 2MJ-48MP 40MJ-2MP 40MJ-40MP 48MJ-48MP 8MJ-6MP-L 8MJ-8MP-L 0MJ-8MP-L 2MJ-2MP-L 6MJ-2MP-L 6MJ-6MP-L 20MJ-20MP-L 24MJ-24MP-L 2MJ-2MP-L Straight Adapter Female MJ-FP Series (240) 2 0MJ-8FP 0MJ-2FP 0MJ-6FP 2MJ-8FP 2MJ-2FP 2MJ-6FP 4MJ-8FP 4MJ-2FP 4MJ-6FP 6MJ-2FP 6MJ-6FP 6MJ-20FP 20MJ-6FP 20MJ-20FP 20MJ-24FP 24MJ-20FP 24MJ-24FP 2MJ-24FP 2MJ-2FP 40MJ-40FP 2MJ-4FJ 2MJ-6FJ MJ-4FJ MJ-6FJ 4MJ-FJ 4MJ-6FJ 4MJ-8FJ 4MJ-0FJ 4MJ-2FJ 4MJ-4FJ 4MJ-6FJ MJ-6FJ MJ-8FJ 6MJ-4FJ 6MJ-FJ 6MJ-6FJ 6MJ-8FJ 6MJ-0FJ 6MJ-2FJ 6MJ-4FJ 6MJ-4FJ 6MJ-20FJ 8MJ-FJ 8MJ-6FJ 8MJ-0FJ 8MJ-2FJ 8MJ-4FJ 8MJ-4FJ 8MJ-20FJ 2MJ-PLUG MJ-PLUG 4MJ-PLUG MJ-PLUG 6MJ-PLUG 8MJ-PLUG 0MJ-PLUG 2 8MJ-24FJ 0MJ-8FJ 0MJ-2FJ 0MJ-4FJ 0MJ-4FJ 0MJ-20FJ 0MJ-24FJ 2MJ-8FJ 2MJ-0FJ 2MJ-2FJ 2MJ-4FJ 2MJ-4FJ 2MJ-20FJ 2MJ-24FJ 4MJ-4FJ 4MJ-20FJ 4MJ-24FJ 6MJ-0FJ 6MJ-2FJ 6MJ-4FJ 6MJ-20FJ 6MJ-24FJ 20MJ-4FJ 20MJ-24FJ 20MJ-2FJ 24MJ-4FJ 24MJ-20FJ 24MJ-2FJ 2MJ-24FJ Plug MJ-PLUG Series (2408) 2MJ-PLUG 4MJ-PLUG 6MJ-PLUG 20MJ-PLUG 24MJ-PLUG 2MJ-PLUG Tube Fitting and Adapters 208

209 HYDRAULIC HOSE FITTINGS AND ADAPTERS Tube Fittings continued 90 Tube Elbow MJ-MJ90 Series (200) 2 90 Male Elbow Extended MJ-MP90 Series (20-L) 2 4 Male Elbow MJ-MP4 Series (20) 2 Side Tee Male MJ-MJ-MP Series (260) 2 2MJ-2MJ90 MJ-MJ90 4MJ-4MJ90 MJ-4MJ90 MJ-MJ90 6MJ-4MJ90 6MJ-MJ90 6MJ-6MJ90 8MJ-4MJ90 8MJ-6MJ90 8MJ-8MJ90 0MJ-8MJ90 0MJ-0MJ90 2MJ-8MJ90 2MJ-0MJ90 2MJ-2MJ90 4MJ-4MJ90 6MJ-2MJ90 6MJ-6MJ90 20MJ-20MJ90 24MJ-24MJ90 2MJ-2MJ90 90 Male Elbow MJ-MP90 Series (20) 4MJ-2MP90-L 4MJ-4MP90-L MJ-2MP90-L MJ-4MP90-L 6MJ-2MP90-L 6MJ-4MP90-L 6MJ-6MP90-L 6MJ-8MP90-L 8MJ-4MP90-L 8MJ-6MP90-L 8MJ-8MP90-L 8MJ-2MP90-L 0MJ-8MP90-L 0MJ-2MP90-L 2MJ-8MP90-L 2MJ-2MP90-L 2MJ-6MP90-L 4MJ-2MP90-L 6MJ-2MP90-L 6MJ-6MP90-L 20MJ-20MP90-L 24MJ-24MP90-L 2MJ-2MP4 MJ-2MP4 4MJ-2MP4 4MJ-4MP4 4MJ-6MP4 4MJ-8MP4 MJ-2MP4 MJ-4MP4 MJ-6MP4 6MJ-2MP4 6MJ-4MP4 6MJ-6MP4 6MJ-8MP4 6MJ-2MP4 8MJ-4MP4 8MJ-6MP4 8MJ-8MP4 8MJ-2MP4 0MJ-6MP4 0MJ-8MP4 0MJ-2MP4 2MJ-8MP4 2MJ-2MP4 2MJ-6MP4 4MJ-2MP4 6MJ-8MP4 6MJ-2MP4 6MJ-6MP4 6MJ-20MP4 20MJ-6MP4 20MJ-20MP4 20MJ-24MP4 24MJ-20MP4 24MJ-24MP4 2MJ-2MP4 40MJ-40MP4 MJ-MJ-2MP 4MJ-4MJ-2MP 4MJ-4MJ-4MP 4MJ-4MJ-6MP MJ-MJ-2MP MJ-MJ-4MP 6MJ-6MJ-2MP 6MJ-6MJ-4MP 6MJ-6MJ-6MP 6MJ-6MJ-8MP 6MJ-0MJ-2MP 8MJ-4MJ-8MP 8MJ-8MJ-4MP 8MJ-8MJ-6MP 8MJ-8MJ-8MP 8MJ-8MJ-2MP 0MJ-0MJ-6MP 0MJ-0MJ-8MP 0MJ-0MJ-2MP 2MJ-6MJ-2MP 2MJ-2MJ-8MP 2MJ-2MJ-2MP 2MJ-2MJ-6MP 2MJ-6MJ-20MP 4MJ-4MJ-2MP 6MJ-2MJ-6MP 6MJ-6MJ-2MP 6MJ-6MJ-6MP 20MJ-20MJ-6MP 20MJ-20MJ-20MP 24MJ-24MJ-24MP 2MJ-2MJ-2MP 2 90 Female Elbow MJ-FP90 Series (202) 2 4 Male Elbow MJ-MJ4 Series (204) 2 Side Tee Female MJ-MJ-FP Series (2602) 2MJ-2MP90 2MJ-4MP90 MJ-2MP90 4MJ-2MP90 4MJ-4MP90 4MJ-6MP90 4MJ-8MP90 4MJ-2MP90 MJ-2MP90 MJ-4MP90 MJ-6MP90 MJ-8MP90 6MJ-2MP90 6MJ-4MP90 6MJ-6MP90 6MJ-8MP90 6MJ-2MP90 8MJ-2MP90 8MJ-4MP90 8MJ-6MP90 8MJ-8MP90 8MJ-2MP90 8MJ-6MP90 0MJ-6MP90 0MJ-8MP90 0MJ-2MP90 0MJ-6MP90 2MJ-6MP90 2MJ-8MP90 2MJ-2MP90 2MJ-6MP90 2MJ-20MP90 4MJ-8MP90 4MJ-2MP90 4MJ-6MP90 6MJ-8MP90 6MJ-2MP90 6MJ-6MP90 6MJ-20MP90 6MJ-24MP90 20MJ-2MP90 20MJ-6MP90 20MJ-20MP90 20MJ-24MP90 24MJ-6MP90 24MJ-20MP90 24MJ-24MP90 2MJ-24MP90 2MJ-2MP90 40MJ-40MP90 Tube Fitting and Adapters 4MJ-2FP90 4MJ-4FP90 4MJ-6FP90 4MJ-8FP90 MJ-2FP90 MJ-4FP90 MJ-6FP90 6MJ-2FP90 6MJ-4FP90 6MJ-6FP90 6MJ-8FP90 8MJ-4FP90 8MJ-6FP90 8MJ-8FP90 8MJ-2FP90 0MJ-6FP90 0MJ-8FP90 0MJ-2FP90 2MJ-8FP90 2MJ-2FP90 2MJ-6FP90 4MJ-2FP90 6MJ-2FP90 6MJ-6FP90 6MJ-20FP90 20MJ-20FP90 24MJ-24FP90 2MJ-2FP90 4MJ-4MJ4 6MJ-4MJ4 6MJ-6MJ4 8MJ-8MJ4 4MJ-4FP4 6MJ-4FP4 6MJ-6FP4 8MJ-6FP4 8MJ-8FP4 0MJ-0MJ4 2MJ-2MJ4 6MJ-6MJ4 20MJ-20MJ4 4 Female Elbow MJ-FP4 Series (20) 2 0MJ-8FP4 2MJ-2FP4 6MJ-6FP4 20MJ-20FP4 2MJ-2FP4 2MJ-2MJ-2FP MJ-MJ-2FP 4MJ-4MJ-2FP 4MJ-4MJ-4FP MJ-MJ-2FP MJ-MJ-4FP 6MJ-6MJ-4FP 6MJ-6MJ-6FP 8MJ-8MJ-4FP 8MJ-8MJ-6FP 8MJ-8MJ-8FP 0MJ-0MJ-4FP 2 0MJ-0MJ-8FP 0MJ-0MJ-2FP 2MJ-2MJ-8FP 2MJ-2MJ-2FP 2MJ-2MJ-6FP 4MJ-4MJ-2FP 6MJ-6MJ-2FP 6MJ-6MJ-6FP 20MJ-20MJ-20FP 24MJ-24MJ-24FP 2MJ-2MJ-2FP 209

210 HYDRAULIC HOSE FITTINGS AND ADAPTERS Tube Fittings continued Tube Tee MJ-MJ-MJ Series (260) Run Tee Female MJ-FP-MJ Series (2606) Branch Tee Female MJ-FP-FP Series (2609) Branch Tee Male FP-FP-MJ Series (262) MJ-2MJ-2MJ MJ-MJ-MJ 4MJ-4MJ-4MJ 4MJ-4MJ-6MJ 4MJ-6MJ-6MJ MJ-MJ-4MJ MJ-MJ-MJ MJ-MJ-6MJ 6MJ-6MJ-4MJ 6MJ-6MJ-MJ 6MJ-6MJ-6MJ 6MJ-6MJ-8MJ 8MJ-6MJ-6MJ 8MJ-8MJ-6MJ 8MJ-8MJ-8MJ 8MJ-8MJ-0MJ 8MJ-8MJ-2MJ 8MJ-2MJ-8MJ 0MJ-8MJ-8MJ 0MJ-0MJ-8MJ 0MJ-0MJ-0MJ 0MJ-0MJ-2MJ 2MJ-8MJ-2MJ 2MJ-0MJ-0MJ 2MJ-2MJ-6MJ 2MJ-2MJ-8MJ 2MJ-2MJ-0MJ 2MJ-2MJ-2MJ 2MJ-2MJ-6MJ 2MJ-2MJ-20MJ 2MJ-6MJ-6MJ 4MJ-4MJ-4MJ 6MJ-0MJ-0MJ 6MJ-2MJ-2MJ 6MJ-2MJ-6MJ 6MJ-6MJ-8MJ 6MJ-6MJ-2MJ 6MJ-6MJ-6MJ 20MJ-20MJ-0MJ 20MJ-20MJ-2MJ 20MJ-20MJ-6MJ 20MJ-20MJ-20MJ 24MJ-24MJ-24MJ 2MJ-2MJ-2MJ Run Tee Male MJ-MP-MJ Series (260) 2 MJ-2FP-MJ MJ-2FP-4MJ 4MJ-2FP-4MJ 4MJ-4FP-4MJ MJ-2FP-MJ MJ-4FP-MJ 6MJ-4FP-6MJ 6MJ-6FP-4MJ 6MJ-6FP-6MJ 4MJ-2MP-2MP 6MJ-4MP-4MP 6MJ-6MP-4MP 6MJ-6MP-6MP 8MJ-6MP-6MP 8MJ-8MP-8MP 8MJ-6FP-8MJ 8MJ-8FP-8MJ 0MJ-8FP-0MJ 2MJ-2FP-2MJ 4MJ-2FP-4MJ 6MJ-6FP-6MJ 20MJ-20FP-20MJ 24MJ-24FP-24MJ 2MJ-2FP-2MJ Run Tee Male MJ-MP-MP Series (2607) 2 0MJ-6MP-6MP 0MJ-8MP-8MP 2MJ-2MP-2MP 6MJ-6MP-6MP 20MJ-20MP-20MP 2MJ-2MP-2MP 4MJ-2FP-2FP MJ-4FP-4FP 6MJ-4FP-4FP 8MJ-6FP-6FP 8MJ-8FP-8FP 0MJ-8FP-8FP 2MJ-2FP-2FP 6MJ-6FP-6FP 20MJ-20FP-20FP 24MJ-24FP-24FP Branch Tee Male MP-MP-MJ Series (260) 4MP-4MP-4MJ 4MP-4MP-6MJ 6MP-6MP-6MJ 6MP-6MP-8MJ 8MP-8MP-8MJ 8MP-8MP-0MJ 2MP-2MP-2MJ 2MP-2MP-6MJ 6MP-6MP-6MJ Branch Tee Female MJ-MP-FP Series (26) 2 2FP-2FP-4MJ 4FP-4FP-6MJ 6FP-6FP-8MJ 8FP-8FP-8MJ 2FP-2FP-2MJ 6FP-6FP-6MJ Branch Tee Male MP-FP-MJ Series (26) 2MP-2FP-4MJ 4MP-4FP-6MJ 6MP-6FP-6MJ 6MP-6FP-8MJ 8MP-8FP-0MJ 2MP-2FP-2MJ 6MP-6FP-6MJ 20MP-20FP-20MJ Tube Cross MJ-MJ-MJ-MJ Series (260) 2 MJ-2MP-MJ 4MJ-2MP-4MJ 4MJ-4MP-4MJ 4MJ-4MP-6MJ MJ-2MP-MJ MJ-4MP-MJ MJ-6MP-MJ MJ-6MP-6MJ 6MJ-2MP-6MJ 6MJ-4MP-6MJ 6MJ-6MP-MJ 6MJ-6MP-6MJ 6MJ-8MP-6MJ 6MJ-8MP-0MJ 8MJ-4MP-8MJ 8MJ-6MP-4MJ 8MJ-6MP-6MJ 8MJ-6MP-8MJ 8MJ-8MP-4MJ 8MJ-8MP-6MJ 8MJ-8MP-8MJ 8MJ-2MP-8MJ 0MJ-8MP-0MJ 0MJ-2MP-0MJ 2MJ-6MP-2MJ 2MJ-8MP-2MJ 2MJ-2MP-8MJ 2MJ-2MP-2MJ 4MJ-2MP-4MJ 6MJ-2MP-6MJ 6MJ-6MP-2MJ 6MJ-6MP-6MJ 20MJ-6MP-20MJ 20MJ-20MP-20MJ 24MJ-24MP-24MJ 2MJ-2MP-2MJ Branch Tee Male MJ-FP-MP Series (2608) 4MJ-2FP-2MP 4MJ-4FP-2MP 4MJ-4FP-4MP 6MJ-4FP-4MP 6MJ-4FP-6MP 2 6MJ-6FP-6MP 8MJ-6FP-6MP 0MJ-8FP-8MP 2MJ-2FP-2MP 6MJ-6FP-6MP 4MJ-2MP-2FP 4MJ-4MP-2FP 4MJ-4MP-4FP 4MJ-8MP-6FP 6MJ-4MP-4FP 6MJ-6MP-6FP 2 8MJ-6MP-6FP 8MJ-8MP-8FP 0MJ-8MP-8FP 2MJ-2MP-2FP 6MJ-6MP-6FP 20MJ-20MP-20FP Tube Fitting and Adapters 2MJ-2MJ-2MJ-2MJ 4MJ-4MJ-4MJ-4MJ MJ-MJ-MJ-MJ 6MJ-6MJ-6MJ-6MJ 8MJ-8MJ-8MJ-8MJ 0MJ-0MJ-0MJ-0MJ 2MJ-2MJ-2MJ-2MJ 4MJ-4MJ-4MJ-4MJ 6MJ-6MJ-6MJ-6MJ 20MJ-20MJ-20MJ-20MJ 24MJ-24MJ-24MJ-24MJ 2MJ-2MJ-2MJ-2MJ

211 HYDRAULIC HOSE FITTINGS AND ADAPTERS Tube Fittings continued Tube Cross MJ-MP-MJ-MJ Series (26) 4 Bulkhead Tube Elbow MJ-BKHD4 Series (2702) Bulkhead Female NPT FP-BKHD Series (270) 90 Swivel Elbow MP-FJX90 Series (60) MJ-4MP-4MJ-4MJ 6MJ-6MP-4MJ-6MJ 6MJ-6MP-6MJ-6MJ 8MJ-8MP-8MJ-8MJ 2MJ-2MP-2MJ-2MJ 6MJ-6MP-6MJ-6MJ Bulkhead Tube Union MJ-BKHD Series (2700) 2MJ-2BKHD MJ-BKHD 4MJ-4BKHD 4MJ-BKHD MJ-BKHD 6MJ-4BKHD 6MJ-6BKHD 8MJ-8BKHD 4 2 0MJ-0BKHD 2MJ-2BKHD 4MJ-4BKHD 6MJ-2BKHD 6MJ-6BKHD 20MJ-20BKHD 24MJ-24BKHD 2MJ-2BKHD 90 Bulkhead Tube Elbow MJ-BKHD90 Series (270) 2 MJ-BKHD4 4MJ-4BKHD4 MJ-BKHD4 6MJ-6BKHD4 8MJ-8BKHD4 0MJ-0BKHD4 MJ-MJ-BKHD 4MJ-4MJ-4BKHD 4MJ-4MJ-6BKHD MJ-MJ-BKHD 6MJ-6MJ-6BKHD 8MJ-8MJ-8BKHD 0MJ-0MJ-0BKHD 2MJ-2MJ-2BKHD 2MJ-2MJ-6BKHD 4MJ-4MJ-4BKHD 6MJ-6MJ-6BKHD 20MJ-20MJ-20BKHD 24MJ-24MJ-24BKHD 2MJ-2BKHD4 4MJ-4BKHD4 6MJ-6BKHD4 20MJ-20BKHD4 24MJ-24BKHD4 2MJ-2BKHD4 Bulkhead Branch Tee MJ-MJ-BKHD Series (270) Bulkhead Run Tee MJ-BKHD-MJ Series (2704) 2 2FP-4BKHD 4FP-4BKHD 4FP-6BKHD 6FP-6BKHD 6FP-8BKHD 8FP-8BKHD 8FP-0BKHD 2MP-4BKHD 4MP-4BKHD 4MP-6BKHD 6MP-6BKHD 6MP-8BKHD 8MP-8BKHD 8MP-0BKHD 2FP-6BKHD 2FP-2BKHD 2FP-4BKHD 6FP-6BKHD 20FP-20BKHD 24FP-24BKHD 2FP-2BKHD Bulkhead Male NPT MP-BKHD Series (2706) 2 8MP-2BKHD 2MP-2BKHD 6MP-6BKHD 20MP-20BKHD 24MP-24BKHD 2MP-2BKHD 90 Swivel Elbow MJ-FJX90 Series (600) 2 2MP-4FJX90 2MP-FJX90 4MP-4FJX90 4MP-FJX90 4MP-6FJX90 MP-4FJX90 6MP-6FJX90 6MP-8FJX90 8MP-6FJX90 8MP-8FJX90 8MP-0FJX90 2MP-8FJX90 2MP-2FJX90 2MP-4FJX90 6MP-6FJX90 20MP-20FJX90 24MP-24FJX90 2MP-2FJX90 4 Swivel Elbow MJ-FJX4 Series (602) 4MJ-4FJX4 MJ-FJX4 6MJ-4FJX4 6MJ-6FJX4 8MJ-8FJX4 0MJ-8FJX4 0MJ-0FJX4 2MJ-2FJX4 4MJ-4FJX4 6MJ-6FJX4 20MJ-20FJX4 24MJ-24FJX4 2MJ-2FJX4 Swivel Adapter Female FP-FJX90 Series (60) 2 2 2MJ-2BKHD90 MJ-BKHD90 4MJ-4BKHD90 MJ-BKHD90 6MJ-6BKHD90 8MJ-8BKHD90 0MJ-0BKHD90 2MJ-2BKHD90 2MJ-6BKHD90 4MJ-4BKHD90 6MJ-2BKHD90 6MJ-6BKHD90 20MJ-20BKHD90 24MJ-24BKHD90 2MJ-2BKHD90 Tube Fitting and Adapters 2MJ-2BKHD-2MJ MJ-BKHD-MJ 4MJ-4BKHD-4MJ MJ-BKHD-MJ 6MJ-6BKHD-6MJ 8MJ-8BKHD-8MJ 0MJ-0BKHD-0MJ 2MJ-2BKHD-2MJ 6MJ-2BKHD-2MJ 6MJ-6BKHD-6MJ 20MJ-20BKHD-20MJ 24MJ-24BKHD-24MJ 2 MJ-FJX90 4MJ-4FJX90 4MJ-6FJX90 MJ-FJX90 MJ-6FJX90 6MJ-4FJX90 6MJ-6FJX90 6MJ-8FJX90 8MJ-6FJX90 8MJ-8FJX90 8MJ-0FJX90 8MJ-2FJX90 0MJ-8FJX90 0MJ-0FJX90 0MJ-2FJX90 2MJ-8FJX90 2MJ-0FJX90 2MJ-2FJX90 2MJ-6FJX90 4MJ-4FJX90 6MJ-6FJX90 20MJ-20FJX90 24MJ-24FJX90 2MJ-2FJX90 4FP-4FJX90 4FP-6FJX90 6FP-6FJX90 6FP-8FJX90 8FP-8FJX90 8FP-0FJX90 0FP-8FJX90 2FP-2FJX90 2

212 HYDRAULIC HOSE FITTINGS AND ADAPTERS Swivel Adapter Male MJ-FJX Series (604) Tube Fittings continued 4 Swivel Elbow FP-FJX4 Series (607) 2 Swivel Tee Run MJ-FJX-MJ Series (6602) Swivel Tee FJX-FJX-FJX Series (6606) 2 4MJ-4FJX MJ-FJX 6MJ-6FJX 6MJ-8FJX 6MJ-0FJX 8MJ-8FJX 2MP-4FJX 4MP-4FJX 4MP-FJX 4MP-6FJX 6MP-6FJX 6MP-8FJX 6MP-0FJX 8MP-8FJX 8MP-0FJX 8MP-2FJX 8MJ-0FJX 8MJ-2FJX 0MJ-0FJX 2MJ-2FJX 6MJ-6FJX 20MJ-20FJX Swivel Adapter Male MP-FJX Series (60) 2 2MP-0FJX 2MP-2FJX 2MP-6FJX 6MP-6FJX 20MP-20FJX 24MP-6FJX 24MP-24FJX 2MP-2FJX 40MP-40FJX 6FP-8FJX4 8FP-6FJX4 8FP-0FJX4 Straight FJX-FJX Series (66) 4FJX-4FJX FJX-FJX 6FJX-6FJX 8FJX-6FJX 8FJX-8FJX 0FJX-8FJX 2 Swivel Tee Outlet MJ-MJ-FJX Series (6600) 0FJX-0FJX 2FJX-2FJX 6FJX-6FJX 20FJX-20FJX 24FJX-24FJX 4MJ-4FJX-4MJ MJ-FJX-4MJ MJ-FJX-MJ 6MJ-6FJX-6MJ 8MJ-8FJX-4MJ 8MJ-8FJX-8MJ 8MJ-8FJX-2MJ 0MJ-0FJX-0MJ 0MJ-0FJX-2MJ 2MJ-2FJX-2MJ 4MJ-4FJX-4MJ 6MJ-6FJX-0MJ 6MJ-6FJX-2MJ 6MJ-6FJX-6MJ 20MJ-20FJX-20MJ 24MJ-24FJX-24MJ 2MJ-2FJX-2MJ Swivel Tee Male Branch FJX-FJX-MJ Series (660) 4FJX-4FJX-4MJ 8FJX-8FJX-8MJ 0FJX-0FJX-0MJ 2FJX-2FJX-2MJ 6FJX-6FJX-6MJ 2 2 4FJX-4FJX-4FJX 6FJX-6FJX-6FJX 8FJX-8FJX-8FJX 0FJX-0FJX-0FJX 2FJX-2FJX-2FJX 6FJX-6FJX-6FJX 90 Sweep MJ-FJX90 Series (670) 4MJ-4FJX90 6MJ-6FJX90 8MJ-8FJX90 0MJ-0FJX MJ-2FJX90 6MJ-6FJX90 20MJ-20FJX90 Swivel Adapter Female FP-FJX Series (606) 2FP-4FJX 4FP-4FJX 4FP-FJX 4FP-6FJX 6FP-6FJX 6FP-8FJX 6FP-0FJX 8FP-6FJX 8FP-8FJX 2 8FP-0FJX 8FP-2FJX 2FP-0FJX 2FP-2FJX 2FP-4FJX 6FP-6FJX 20FP-20FJX 24FP-24FJX 2FP-2FJX 4MJ-4MJ-4FJX 4MJ-4MJ-4FJX 6MJ-6MJ-6FJX 6MJ-6MJ-8FJX 8MJ-8MJ-8FJX 0MJ-0MJ-0FJX 2MJ-2MJ-0FJX 2 2MJ-2MJ-2FJX 4MJ-4MJ-4FJX 6MJ-6MJ-6FJX 20MJ-20MJ-20FJX 24MJ-24MJ-24FJX 2MJ-2MJ-2FJX Swivel Tee Male Branch FJX-FJX-MP Series (6604) 2 4FJX-4FJX-4MP 2FJX-2FJX-2MP Swivel Tee Female Branch FJX-FJX-FP Series (660) 2 90 Sweep Long MJ-FJX90 Series (670-L) 4MJ-4FJX90-L 6MJ-6FJX90-L 8MJ-8FJX90-L 0MJ-0FJX90-L 2MJ-2FJX90-L 6MJ-6FJX90-L Tube Fitting and Adapters 2 4FJX-4FJX-4FP 22

213 HYDRAULIC HOSE FITTINGS AND ADAPTERS Adapter Unions O.R.B. Adapter MB-FPX Series (6900) 2 90 O.R.B. Adjustable Adapter MB-FPX90 Series (690-NWO) 2 4 O.R.B. Adjustable Adapter MB-FPX4 Series (6902-NWO) 2 4MB-2FPX 4MB-4FPX 4MB-6FPX 4MB-8FPX MB-4FPX MB-8FPX 6MB-4FPX 6MB-6FPX 6MB-8FPX 8MB-4FPX 8MB-6FPX 8MB-8FPX 8MB-2FPX 0MB-6FPX 0MB-8FPX 0MB-2FPX 2MB-6FPX 2MB-8FPX 2MB-2FPX 2MB-6FPX 4MB-2FPX 4MB-6FPX 6MB-8FPX 6MB-2FPX 6MB-6FPX 6MB-20FPX 20MB-2FPX 20MB-6FPX 20MB-20FPX 24MB-20FPX 24MB-24FPX 2MB-2FPX 4MB-2FPX90 4MB-4FPX90 4MB-4FPX90 4MB-6FPX90 4MB-8FPX90 MB-4FPX90 6MB-4FPX90 6MB-6FPX90 6MB-8FPX90 6MB-2FPX90 8MB-4FPX90 8MB-6FPX90 8MB-8FPX90 8MB-2FPX90 0MB-4FPX90 0MB-6FPX90 0MB-8FPX90 0MB-2FPX90 2MB-6FPX90 2MB-8FPX90 2MB-2FPX90 2MB-6FPX90 4MB-2FPX90 4MB-6FPX90 6MB-2FPX90 6MB-6FPX90 6MB-20FPX90 20MB-2FPX90 20MB-6FPX90 20MB-20FPX90 24MB-20FPX90 24MB-24FPX90 2MB-2FPX90 2MB-2FPX4 MB-4FPX4 4MB-4FPX4 4MB-6FPX4 6MB-4FPX4 6MB-6FPX4 6MB-8FPX4 8MB-4FPX4 8MB-6FPX4 8MB-8FPX4 8MB-2FPX4 0MB-6FPX4 0MB-8FPX4 0MB-2FPX4 2MB-6FPX4 2MB-8FPX4 2MB-2FPX4 2MB-6FPX4 4MB-2FPX4 6MB-2FPX4 6MB-6FPX4 6MB-20FPX4 20MB-6FPX4 20MB-20FPX4 24MB-24FPX4 O-Ring OR Series (4000) Adjustable & O-Ring Fittings Washer BW Series (6000) Straight Connector MB-MJ Series (6400) Straight Connector (continued) MB-MJ Series (6400) 2OR OR 4OR OR 6OR 8OR 0OR 2OR 4OR 6OR 20OR 24OR 2OR Tube Fitting and Adapters 2BW BW 4BW BW 6BW 8BW 0BW 2BW 4BW 6BW 20BW 24BW 2BW O.R.B. Connector MB-MB Series (474-NWO) 4MB-4MB 6MB-6MB 8MB-8MB 0MB-0MB 2MB-2MB 6MB-2MB 2 6MB-6MB 20MB-20MB 24MB-6MB 24MB-24MB 2MB-2MB 2MB-2MJ 2MB-MJ 2MB-4MJ MB-MJ MB-4MJ 4MB-MJ 4MB-4MJ 4MB-MJ 4MB-6MJ 4MB-8MJ 4MB-0MJ MB-4MJ MB-MJ MB-6MJ MB-8MJ 6MB-2MJ 6MB-4MJ 6MB-MJ 6MB-6MJ 6MB-8MJ 6MB-0MJ 6MB-2MJ 6MB-6MJ 8MB-4MJ 8MB-MJ 8MB-6MJ 2 8MB-8MJ 8MB-0MJ 8MB-2MJ 8MB-4MJ 8MB-6MJ 0MB-4MJ 0MB-MJ 0MB-6MJ 0MB-8MJ 0MB-0MJ 0MB-2MJ 0MB-4MJ 0MB-6MJ 0MB-20MJ 2MB-4MJ 2MB-6MJ 2MB-8MJ 2MB-0MJ 2MB-2MJ 2MB-4MJ 2MB-6MJ 2MB-20MJ 4MB-8MJ 4MB-0MJ 4MB-2MJ 4MB-4MJ 4MB-6MJ 6MB-6MJ 6MB-8MJ 6MB-0MJ 6MB-2MJ 6MB-4MJ 6MB-6MJ 6MB-20MJ 6MB-24MJ 20MB-8MJ 20MB-0MJ 20MB-2MJ 20MB-6MJ 20MB-20MJ 20MB-24MJ 20MB-2MJ 24MB-6MJ 24MB-20MJ 24MB-24MJ 24MB-2MJ 2MB-24MJ 2MB-2MJ 2

214 HYDRAULIC HOSE FITTINGS AND ADAPTERS Adjustable & O-Ring Fittings continued Straight Connector Extended MB-MJ-L Series (6400-L) O.R.B. Adapter Female FB-MP Series (6404) O.R.B. Plug MB-PLUG Series (6408) Straight FB-FP Series (6420) MB-4MJ-L 4MB-6MJ-L MB-MJ-L 6MB-6MJ-L 8MB-6MJ-L 8MB-8MJ-L 8MB-2MJ-L 0MB-8MJ-L 0MB-0MJ-L 0MB-2MJ-L 2MB-2MJ-L 4MB-4MJ-L 6MB-8MJ-L 6MB-0MJ-L 6MB-2MJ-L 6MB-6MJ-L 20MB-20MJ-L 24MB-24MJ-L O.R.B. Adapter Male MB-MP Series (640) 2FB-2MP FB-6MP 4FB-2MP 4FB-4MP 4FB-6MP FB-2MP FB-4MP FB-6MP 6FB-4MP 6FB-6MP 6FB-8MP 8FB-6MP 8FB-8MP 8FB-2MP 0FB-6MP 0FB-8MP 0FB-2MP 2FB-8MP 2FB-2MP 2FB-6MP 4FB-2MP 6FB-2MP 6FB-6MP 6FB-20MP 20FB-6MP 20FB-20MP 24FB-24MP 2FB-2MP 2MB-PLUG MB-PLUG 4MB-PLUG MB-PLUG 6MB-PLUG 8MB-PLUG 0MB-PLUG 2MB-PLUG 4MB-PLUG 6MB-PLUG 20MB-PLUG 24MB-PLUG 2MB-PLUG O.R.B. Port Bushing MB-FB Series (640) 2 6FB-6FP 8FB-8FP 0FB-8FP Straight FB-FB Series (642) 8FB-8FB 2 0FB-0FB MB-2MP 4MB-2MP 4MB-4MP MB-2MP MB-4MP 6MB-2MP 6MB-4MP 6MB-6MP 6MB-8MP 8MB-4MP 8MB-6MP 8MB-8MP 8MB-2MP 0MB-4MP 0MB-6MP 0MB-8MP 0MB-2MP 2MB-6MP 4MB-4FJX 4MB-6FJX 6MB-4FJX 6MB-6FJX 6MB-8FJX 8MB-8FJX 8MB-0FJX 2 2MB-8MP 2MB-2MP 2MB-6MP 4MB-2MP 4MB-6MP 6MB-6MP 6MB-2MP 6MB-6MP 6MB-20MP 20MB-2MP 20MB-6MP 20MB-20MP 24MB-2MP 24MB-6MP 24MB-20MP 24MB-24MP 2MB-2MP O.R.B. Swivel Adapter MB-FJX Series (6402) 2 0MB-0FJX 2MB-0FJX 2MB-2FJX 6MB-6FJX 20MB-20FJX 24MB-24FJX 2MB-2FJX O.R.B. Adapter MB-FP Series (640) 2MB-2FP 2MB-4FP 2MB-6FP MB-4FP 4MB-2FP 4MB-4FP 4MB-6FP MB-2FP MB-4FP MB-6FP 6MB-2FP 6MB-4FP 6MB-6FP 6MB-8FP 8MB-2FP 8MB-4FP 8MB-6FP 8MB-8FP 8MB-2FP 0MB-4FP 0MB-6FP 0MB-8FP 0MB-2FP 2MB-2FP 2MB-4FP 2MB-6FP 2MB-8FP 2 2MB-2FP 2MB-6FP 4MB-8FP 4MB-2FP 4MB-6FP 6MB-4FP 6MB-6FP 6MB-8FP 6MB-2FP 6MB-6FP 6MB-20FP 6MB-24FP 20MB-8FP 20MB-2FP 20MB-6FP 20MB-20FP 20MB-24FP 20MB-2FP 24MB-2FP 24MB-6FP 24MB-20FP 24MB-24FP 2MB-6FP 2MB-20FP 2MB-24FP 2MB-2FP 4MB-2FB 4MB-4FB 4MB-4FB 4MB-FB 4MB-6FB MB-4FB MB-6FB 6MB-4FB 6MB-6FB 6MB-8FB 6MB-2FB 8MB-FB 8MB-4FB 8MB-6FB 8MB-8FB 8MB-0FB 8MB-2FB 0MB-4FB 0MB-FB 0MB-6FB 0MB-8FB 0MB-2FB 0MB-6FB 2MB-4FB 2MB-6FB 2MB-8FB 2MB-0FB 2MB-2FB 2MB-4FB 2MB-6FB 2MB-20FB 4MB-8FB 4MB-0FB 4MB-2FB 4MB-6FB 6MB-4FB 6MB-6FB 6MB-8FB 6MB-0FB 6MB-2FB 6MB-4FB 6MB-6FB 6MB-20FB 6MB-24FB 20MB-6FB 20MB-0FB 20MB-2FB 20MB-6FB 20MB-24FB 24MB-2FB 24MB-6FB 24MB-20FB 2MB-2FB 2MB-6FB 2MB-20FB 2MB-24FB 40MB-24FB Tube Fitting and Adapters 90 Adjustable Elbow MB-MJ90 Series (680-NWO) 2MB-2MJ90 MB-MJ90 4MB-4MJ90 4MB-MJ90 4MB-6MJ90 4MB-8MJ90 MB-4MJ90 MB-MJ90 MB-6MJ90 MB-8MJ90 6MB-4MJ90 6MB-MJ90 6MB-6MJ90 6MB-8MJ0 6MB-0MJ90 6MB-2MJ90 8MB-4MJ90 8MB-MJ90 8MB-6MJ90 8MB-8MJ90 8MB-0MJ90 8MB-2MJ90 8MB-6MJ90 0MB-MJ90 0MB-6MJ90 0MB-8MJ90 0MB-0MJ90 0MB-2MJ90 0MB-6MJ90 2 0MB-20MJ90 2MB-6MJ90 2MB-8MJ90 2MB-0MJ90 2MB-2MJ90 2MB-4MJ90 2MB-6MJ90 2MB-20MJ90 4MB-2MJ90 4MB-4MJ90 4MB-6MJ90 6MB-8MJ90 6MB-0MJ90 6MB-2MJ90 6MB-4MJ90 6MB-6MJ90 6MB-20MJ90 6MB-24MJ90 20MB-0MJ90 20MB-2MJ90 20MB-6MJ90 20MB-20MJ90 20MB-24MJ90 24MB-6MJ90 24MB-20MJ90 24MB-24MJ90 24MB-2MJ90 2MB-24MJ90 24

215 90 Adjustable Elbow Extended MB-MJ90-L Series (680-L-NWO) HYDRAULIC HOSE FITTINGS AND ADAPTERS Adjustable & O-Ring Fittings continued Branch Tee Adjustable MJ-MJ-MB Series (680-NWO) 90 Adjustable Elbow Female MB-FP90 Series (680-NWO ) 2 4 O.R.B. Boss Connector MB-MB4 Series (6808-NWO) 2 4MB-4MJ90-L 4MB-6MJ90-L 6MB-6MJ0-L 6MB-8MJ90-L 8MB-6MJ90-L 8MB-8MJ90-L 0MB-8MJ90-L MB-MJ4 4MB-4MJ4 4MB-MJ4 4MB-6MJ4 4MB-8MJ4 MB-4MJ4 MB-MJ4 MB-6MJ4 6MB-4MJ4 6MB-MJ4 6MB-6MJ4 6MB-8MJ4 6MB-2MJ4 8MB-4MJ4 8MB-6MJ4 8MB-8MJ4 8MB-0MJ4 8MB-2MJ4 0MB-6MJ4 0MB-8MJ4 0MB-0MJ4 2 0MB-0MJ90-L 0MB-2MJ90-L 2MB-0MJ90-L 2MB-2MJ90-L 6MB-2MJ90-L 6MB-6MJ90-L 20MB-20MJ90-L 4 Adjustable Elbow MB-MJ4 Series (6802-NWO) 2 0MB-2MJ4 2MB-6MJ4 2MB-8MJ4 2MB-0MJ4 2MB-2MJ4 2MB-4MJ4 2MB-6MJ4 4MB-2MJ4 4MB-4MJ4 4MB-6MJ4 6MB-8MJ4 6MB-2MJ4 6MB-6MJ4 6MB-20MJ4 20MB-6MJ4 20MB-20MJ4 20MB-24MJ4 24MB-20MJ4 24MB-24MJ4 2MB-2MJ4 4MJ-4MJ-4MB 4MJ-4MJ-6MB MJ-MJ-MB 6MJ-6MJ-4MB 6MJ-6MJ-MB 6MJ-6MJ-6MB 6MJ-6MJ-8MB 6MJ-6MJ-2MB 8MJ-6MJ-4MB 8MJ-6MJ-6MB 8MJ-8MJ-6MB 8MJ-8MJ-8MB 8MJ-8MJ-0MB 8MJ-8MJ-2MB 0MJ-0MJ-8MB 4MJ-4MB-4MJ 4MJ-6MB-4MJ MJ-4MB-MJ MJ-MB-MJ 6MJ-4MB-6MJ 6MJ-MB-6MJ 6MJ-6MB-4MJ 6MJ-6MB-6MJ 6MJ-8MB-6MJ 6MJ-2MB-8MJ 6MJ-2MB-2MJ 8MJ-6MB-4MJ 8MJ-6MB-8MJ 8MJ-8MB-8MJ 8MJ-0MB-8MJ 8MJ-2MB-6MJ 8MJ-2MB-8MJ 0MJ-8MB-0MJ 0MJ-0MB-0MJ 2 0MJ-0MJ-0MB 0MJ-0MJ-2MB 0MJ-0MJ-6MB 2MJ-2MJ-6MB 2MJ-2MJ-8MB 2MJ-2MJ-0MB 2MJ-2MJ-2MB 2MJ-2MJ-6MB 4MJ-4MJ-4MB 6MJ-4MJ-6MB 6MJ-6MJ-2MB 6MJ-6MJ-6MB 20MJ-20MJ-20MB 24MJ-24MJ-24MB 2MJ-2MJ-2MB Run Tee Adjustable MJ-MB-MJ Series (6804-NWO) 2 0MJ-2MB-0MJ 0MJ-6MB-8MJ 2MJ-8MB-2MJ 2MJ-0MB-2MJ 2MJ-2MB-6MJ 2MJ-2MB-8MJ 2MJ-2MB-0MJ 2MJ-2MB-2MJ 2MJ-2MB-6MJ 4MJ-4MB-4MJ 6MJ-2MB-6MJ 6MJ-4MB-6MJ 6MJ-6MB-6MJ 6MJ-6MB-20MJ 20MJ-6MB-20MJ 20MJ-20MB-20MJ 24MJ-20MB-24MJ 24MJ-24MB-24MJ 2MJ-2MB-2MJ 4MB-2FP90 4MB-4FP90 MB-2FP90 6MB-4FP90 6MB-6FP90 8MB-6FP90 8MB-8FP90 0MB-6FP90 0MB-8FP90 4MB-2MP90 4MB-4MP90 MB-2MP90 6MB-4MP90 6MB-6MP90 8MB-6MP90 8MB-8MP90 0MB-8MP90 2MB-8FP90 2MB-2FP90 4MB-2FP90 6MB-2FP90 6MB-6FP90 20MB-20FP90 24MB-24FP90 2MB-2FP90 90 Adjustable Elbow Male MB-MP90 Series (6806-NWO) 4MB-4MB90 6MB-6MB90 8MB-8MB90 0MB-8MB90 0MB-0MB90 2 2MB-2MP90 2MB-6MP90 4MB-2MP90 6MB-2MP90 6MB-6MP90 20MB-20MP90 24MB-24MP90 2MB-2MP90 90 O.R.B. Boss Connector MB-MB90 Series (6807-NWO) 2 2MB-2MB90 6MB-4MB90 6MB-6MB90 20MB-20MB90 24MB-24MB90 4MB-4MB4 4MB-4FJX90 6MB-4FJX90 6MB-6FJX90 8MB-6FJX90 8MB-8FJX90 8MB-2FJX90 6MB-6MB4 90 O.R.B. Adjustable Elbow MB-FJX90 Series (6809-NWO) 4MB-4FJX4 6MB-4FJX4 6MB-6FJX4 2 0MB-0FJX90 2MB-0FJX90 2MB-2FJX90 6MB-6FJX90 20MB-20FJX90 4 O.R.B. Adjustable Elbow MB-FJX4 Series (680-NWO) 2 8MB-8FJX4 2MB-2FJX4 Tube Fitting and Adapters 2

216 HYDRAULIC HOSE FITTINGS AND ADAPTERS Pipe Fittings 90 Dot Street Elbow MP-FP90 DOT Series (0) 2 Pipe Reducer Coupling MP-FP Series (40) 2 90 Pipe Elbow Male MP-MP90 Series (00) 2 90 Pipe Elbow Female FP-FP90 Series (04) 2 2MP-2FP90 DOT 4MP-4FP90 DOT 6MP-6FP90 DOT 8MP-8FP90 DOT 2MP-2FP90 DOT Pipe Coupling Female FP-FP Series (000) 2FP-2FP 4FP-2FP 4FP-4FP 6FP-2FP 6FP-4FP 6FP-6FP 8FP-2FP 8FP-4FP 8FP-6FP 8FP-8FP 2FP-6FP 2 2FP-8FP 2FP-2FP 6FP-8FP 6FP-2FP 6FP-6FP 20FP-6FP 20FP-20FP 24FP-20FP 24FP-24FP 2FP-2FP Pipe Coupling Male MP-MP Series (404) 2 2MP-2FP 2MP-4FP 2MP-6FP 2MP-8FP 4MP-2FP 4MP-4FP 4MP-6FP 4MP-8FP 4MP-2FP 6MP-2FP 6MP-4FP 6MP-6FP 6MP-8FP 6MP-2FP 8MP-4FP 8MP-6FP 8MP-8FP 8MP-2FP 8MP-6FP 2MP-4FP 2FP-CAP 4FP-CAP 6FP-CAP 8FP-CAP 2MP-6FP 2MP-8FP 2MP-2FP 2MP-6FP 2MP-20FP 6MP-6FP 6MP-8FP 6MP-2FP 6MP-6FP 6MP-20FP 6MP-24FP 6MP-2FP 20MP-6FP 20MP-20FP 20MP-24FP 20MP-2FP 24MP-20FP 24MP-24FP 24MP-2FP 2MP-2FP Plug Cap FP-CAP Series (406-C) 2FP-CAP 6FP-CAP 20FP-CAP 2MP-2MP90 4MP-2MP90 4MP-4MP90 6MP-2MP90 6MP-4MP90 6MP-6MP90 8MP-4MP90 8MP-6MP90 8MP-8MP90 2MP-6MP90 2MP-8MP90 2MP-2MP90 6MP-8MP90 6MP-2MP90 6MP-6MP90 20MP-20MP90 24MP-24MP90 2MP-2MP90 90 Street Elbow MP-FP90 Series (02) 2MP-2FP90 2MP-4FP90 2MP-6FP90 4MP-2FP90 4MP-4FP90 4MP-6FP90 6MP-4FP90 6MP-6FP90 6MP-8FP90 8MP-4FP90 8MP-6FP90 8MP-8FP90 8MP-2FP90 2 2MP-6FP90 2MP-8FP90 2MP-2FP90 2MP-6FP90 6MP-8FP90 6MP-2FP90 6MP-6FP90 6MP-20FP90 20MP-6FP90 20MP-20FP90 20MP-24FP90 24MP-24FP90 2MP-2FP90 2FP-2FP90 4FP-2FP90 4FP-4FP90 6FP-4FP90 6FP-6FP90 8FP-4FP90 8FP-6FP90 8FP-8FP90 2FP-6FP90 2FP-8FP90 2FP-2FP90 6FP-8FP90 6FP-2FP90 6FP-6FP90 20FP-2FP90 20FP-6FP90 20FP-20FP90 24FP-20FP90 24FP-24FP90 2FP-2FP90 4 Pipe Elbow Female MP-FP4 Series (0) 2FP-2FP4 4FP-4FP4 6FP-6FP4 8FP-8FP4 2FP-2FP4 6FP-6FP4 20FP-20FP4 Pipe Tee Male MP-MP-MP Series (600) 2 2MP-2MP 4MP-MP 4MP-2MP 4MP-4MP 6MP-2MP 6MP-4MP 6MP-6MP 8MP-4MP 8MP-6MP 8MP-8MP 2MP-4MP 2MP-6MP 2MP-8MP 2MP-2MP 6MP-4MP 6MP-6MP 26 6MP-8MP 6MP-2MP 6MP-6MP 20MP-2MP 20MP-6MP 20MP-20MP 24MP-2MP 24MP-6MP 24MP-20MP 24MP-24MP 2MP-2MP 2MP-6MP 2MP-20MP 2MP-24MP 2MP-2MP 40MP-40MP Square Head Pipe Plug MP-PLUG Series (406-SHP) 2MP-PLUG 4MP-PLUG 6MP-PLUG 8MP-PLUG 2MP-PLUG 6MP-PLUG 20MP-PLUG 24MP-PLUG 2MP-PLUG 4 Street Elbow MP-FP4 Series (0) 2MP-2FP4 2MP-4FP4 4MP-4FP4 6MP-6FP4 8MP-8FP4 2 2MP-2FP4 6MP-6FP4 20MP-20FP4 24MP-24FP4 2MP-2FP4 2MP-2MP-2MP 4MP-4MP-4MP 6MP-6MP-6MP 8MP-8MP-8MP 2MP-2MP-2MP 6MP-6MP-6MP 20MP-20MP-20MP 2MP-2MP-2MP Tube Fitting and Adapters 2

217 HYDRAULIC HOSE FITTINGS AND ADAPTERS Pipe Tee Female Branch MP-MP-FP Series (60) Pipe Fittings continued Pipe Tee Male Branch FP-FP-MP Series (604) Pipe Cross Female FP-FP-FP-FP Series (62) 90 Swivel Pipe Elbow MP-MPX Series (700) MP-2MP-2FP 4MP-4MP-4FP 6MP-6MP-6FP 8MP-8MP-8FP 2MP-2FP-2FP 2MP-4FP-4FP 4MP-4FP-4FP 6MP-6FP-6FP 8MP-8FP-8FP 2MP-2MP-2FP 6MP-6MP-6FP 20MP-20MP-20FP 2MP-2MP-2FP Service Tee Female Branch MP-FP-FP Series (602) 2 2MP-2FP-2FP 6MP-6FP-6FP 20MP-20FP-20FP 24MP-24FP-24FP 2MP-2FP-2FP Pipe Tee Male Branch MP-FP-MP Series (60) 2 2FP-2FP-2MP 4FP-4FP-4MP 6FP-6FP-6MP 6FP-6FP-8MP 8FP-8FP-8MP 2FP-2FP-8MP 2FP-2FP-2FP 4FP-4FP-2FP 4FP-4FP-4FP 4FP-4FP-6FP 6FP-6FP-6FP 6FP-6FP-8FP 8FP-8FP-8FP 2FP-2FP-2MP 6FP-6FP-6MP 20FP-20FP-20MP 24FP-24FP-24MP 2FP-2FP-2MP Pipe Tee Female FP-FP-FP Series (60) 2 2FP-2FP-2FP 6FP-6FP-6FP 20FP-20FP-6FP 20FP-20FP-20FP 24FP-24FP-24FP 2FP-2FP-2FP Pipe Cross Male MP-MP-MP-MP Series (60) 2FP-2FP-2FP-2FP 4FP-4FP-4FP-4FP 6FP-6FP-6FP-6FP 8FP-8FP-8FP-8FP 2FP-2FP-2FP-2FP 6FP-6FP-6FP-6FP 20FP-20FP-20FP-20FP 24FP-24FP-24FP-24FP 2FP-2FP-2FP-2FP 4MP-4MP-4FP-4FP 4 Pipe Cross Female Branch MP-MP-FP-FP Series (6) 4 Pipe Cross Female Branch MP-FP-FP-FP Series (6) 2 4MP-4MPX90 6MP-6MPX 90 8MP-8MPX90 2MP-2MPX90 90 Swivel Elbow MJ-MPX Series (70) 4MJ-4MPX90 6MJ-4MPX90 6MJ-6MPX90 8MJ-6MPX90 8MJ-8MPX90 0MJ-8MPX90 2MJ-2MPX90 90 Swivel Pipe Elbow FP-MPX Series (702) 2 2 2MP-2FP-2MP 4MP-4FP-4MP 6MP-6FP-6MP 8MP-8FP-8MP 2MP-2FP-8MP 2MP-2FP-2MP 6MP-6FP-6MP 20MP-20FP-20MP 24MP-24FP-24MP 2MP-2FP-2MP 4 4MP-4MP-4MP-4MP 2 4MP-4FP-4FP-4FP 6MP-6FP-6FP-6FP 8MP-8FP-8FP-8FP 2MP-2FP-2FP-2FP 4 2 4FP-4MPX90 6FP-6MPX90 8FP-8MPX90 2FP-2MPX90 Tube Fitting and Adapters 27

218 HYDRAULIC HOSE FITTINGS AND ADAPTERS BSP (British Standard Pipe) Thread Adapters Male BSPP with O-Ring to Male JIC Male BSPP to Male JIC (7 Flare) Male BSPT (Tapered) to Male JIC (7 Flare) BSPP JIC Thread Thread (In.) (In.) MBSPPOR-4MJ MBSPPOR-4MJ MBSPPOR-6MJ MBSPPOR-4MJ MBSPPOR-6MJ MBSPPOR-8MJ MBSPPOR-6MJ MBSPPOR-8MJ MBSPPOR-2MJ MBSPPOR-2MJ 6 2 6MBSPPOR-6MJ MBSPPOR-20MJ BSPP JIC Thread Thread (In.) (In.) MBSPP-4MJ MBSPP-6MJ MBSPP-8MJ MBSPP-0MJ MBSPP-2MJ 6 2 6MBSPP-6MJ Male BSPP to Swivel Female JIC (7 Flare) MBSPT JIC Thread Thread (In.) (In.) MBSPT-4MJ MBSPT-4MJ MBSPT-6MJ MBSPT-8MJ MBSPT-0MJ MBSPT-2MJ 6 2 6MBSPT-6MJ Female BSPP to Male JIC (7 Flare) Male BSPP with O-Ring to Male JIC 90 BSPP JIC Thread Thread (In.) (In.) MBSPP-6MJ MBSPP-8MJ MBSPP-2MJ90 Male BSPP to NPTF Solid Male (Straight) BSPP JIC Thread Thread (In.) (In.) MBSPP-4FJX MBSPP-6FJX MBSPP-8FJX MBSPP-0FJX MBSPP-2FJX 6 2 6MBSPP-6FJX Male BSPP to Female BSPP Swivel FBSPP JIC Thread Thread (In.) (In.) FBSPP-4MJ FBSPP-4MJ FBSPP-6MJ FBSPP-6MJ FBSPP-8MJ FBSPP-2MJ 6 2 6FBSPP-6MJ FBSPP-20MJ Female BSPP Swivel to Male JIC (7 Flare) BSPP JIC Thread Thread (In.) (In.) MBSPP-4MP MBSPP-6MP MBSPP-8MP MBSPP-2MP 2 6MBSPP-6MP MBSPP FBSPPX Thread Thread (In.) (In.) MBSPP-4FBSPPX MBSPP-6FBSPPX MBSPP-8FBSPPX MBSPP-0FBSPPX MBSPP-2FBSPPX 6MBSPP-6FBSPPX BSPP JIC Thread Thread (In.) (In.) FBSPPX-4MJ FBSPPX-6MJ FBSPPX-8MJ FBSPPX-0MJ FBSPPX-2MJ 6 2 6FBSPPX-6MJ 28

219 HYDRAULIC HOSE FITTINGS AND ADAPTERS BSP (British Standard Pipe) Thread Adapters continued Female BSPP Swivel to Female JIC (7 Flare) Swivel BSPP JIC Thread Thread (In.) (In.) FBSPPX-4FJX FBSPPX-6FJX FBSPPX-8FJX FBSPPX-0FJX FBSPPX-2FJX 6 2 6FBSPPX-6FJX Male Metric with O-Ring to Male JIC (7 Flare) Metric Thread Adapters Male DIN to Male JIC (7 Flare) (Light Series) Male DIN to Male JIC (7 Flare) (Heavy Series) JIC Male (MJ) Metric Thread Thread (In.) M0 x MM-4MJ M2 x MM-4MJ M4 x MM-6MJ M6 x MM-6MJ M6 x MM-8MJ M8 x MM-8MJ M8 x MM-0MJ M20 x MM-0MJ M22 x MM-0MJ M22 x MM-2MJ M27 x MM-2MJ M x MM-6MJ M42 x MM-20MJ DIN DIN JIC Male *Tube* Male Metric O.D. Thread Thread (mm) (In.) M4 x MDL-4MJ M6 x MDL-6MJ M8 x MDL-6MJ M22 x. 4 6 MDL-8MJ M26 x MDL-0MJ M0 x MDL-2MJ M6 x MDL-6MJ *DIN light and heavy series couplings can be distinguished from each other by the tube O.D. Heavy series have a smaller O.D. tube than the light. DIN DIN JIC Male *Tube* Male Metric O.D. Thread Thread (mm) (In.) M8 x MDH-4MJ M22 x MDH-6MJ M24 x MDH-8MJ M0 x MDH-0MJ M6 x MDH-2MJ M42 x MDH-6MJ *DIN light and heavy series couplings can be distinguished from each other by the tube O.D. Heavy series have a smaller O.D. tube than the light. 29

220 HYDRAULIC HOSE FITTINGS AND ADAPTERS Metric Thread Adapters continued Female DIN Swivel to Male JIC (7 Flare) (Light Series) Female DIN Swivel to Male JIC (7 Flare) (Heavy Series) DIN DIN JIC Female *Tube* (MJ) Metric O.D. Thread Thread (mm) (In.) M4 x FDLX-4MJ M6 x FDLX-6MJ M8 x FDLX-6MJ M22 x. 4 6 FDLX-8MJ M0 x FDLX-2MJ M6 x FDLX-6MJ *DIN light and heavy series couplings can be distinguished from each other by the tube O.D. Heavy series have a smaller O.D. tube than the light. DIN DIN JIC Female *Tube* (MJ) Metric O.D. Thread Thread (mm) (In.) M8 x FDHX-4MJ M6 x FDHX-MJ M22 x FDHX-6MJ M24 x FDHX-8MJ M0 x FDHX-0MJ M6 x FDHX-2MJ M42 x FDHX-6MJ M2 x FDHX-20MJ *DIN light and heavy series couplings can be distinguished from each other by the tube O.D. Heavy series have a smaller O.D. tube than the light. 220 Flat-Face O-Ring Plugs, Caps and Adapters Pressure Rated at 6000 psi Maximum ( 4 through 6) O-Rings Included Flat-Face O-Ring Cap Thread Size (In.) FFOR-CAP 6 6 6FFOR-CAP 6 6 8FFOR-CAP 4 0FFOR-CAP 6 2 2FFOR-CAP FFOR-CAP FFOR-CAP FFOR-CAP Flat-Face O-Ring Plug Thread Size (In.) MFFOR-PLUG 6 6 6MFFOR-PLUG 6 6 8MFFOR-PLUG 4 0MFFOR-PLUG 6 2 2MFFOR-PLUG MFFOR-PLUG MFFOR-PLUG MFFOR-PLUG Male Flat-Face O-Ring to NPTF Solid Male A B Thread Thread Size Size (In.) (In.) MFFOR-2MP MFFOR-4MP MFFOR-6MP MFFOR-4MP MFFOR-6MP MFFOR-8MP MFFOR-6MP MFFOR-8MP MFFOR-8MP MFFOR-2MP MFFOR-6MP *20MFFOR-20MP* *Pressure rated at 4000 psi maximum. Male Flat-Face O-Ring to Male O-Ring Boss Solid A B Thread Thread Size Size (In.) (In.) MFFOR-4MB MFFOR-6MB MFFOR-8MB MFFOR-6MB MFFOR-8MB MFFOR-0MB MFFOR-6MB MFFOR-8MB MFFOR-0MB MFFOR-2MB MFFOR-0MB MFFOR-8MB MFFOR-2MB MFFOR-6MB MFFOR-2MB MFFOR-6MB L6MFFOR-6MBL *20MFFOR-6MB* *20MFFOR-20MB* *L20MFFOR-20MBL* *Pressure rated at 4000 psi maximum.

221 HYDRAULIC HOSE FITTINGS AND ADAPTERS Flat-Face O-Rings Adapters continued Pressure Rated at 6000 psi Maximum ( 4 through 6) O-Rings Included Male Flat-Face O-Ring to Male O-Ring Boss 4 Male Flat-Face O-Ring on Run Male O-Ring Boss (Tee) Female Flat-Face O-Ring to Male JIC (7 Flare) A B Thread Thread Size Size (In.) (In.) MFFOR-6MB MFFOR-6MB MFFOR-0MB4 A B Thread Thread Size Size (In.) (In.) MFFOR-6MFFOR-6MB MFFOR-2MFFOR-2MB MFFOR-6MFFOR-6MB A B Thread Thread Size Size (In.) (In.) FFORX-4MJ FFORX-6MJ FFORX-8MJ FFORX-0MJ FFORX-2MJ FFORX-6MJ Male Flat-Face O-Ring to Male O-Ring Boss Solid 90 Male Flat-Face O-Ring to Male O-Ring Boss on Run Male Flat-Face O-Ring Branch (Tee) Male Flat-Face O-Ring to Female Flat-Face O-Ring Swivel 90 A B Thread Thread Size Size (In.) (In.) MFFOR-4MB MFFOR-4MB MFFOR-6MB MFFOR-0MB MFFOR-8MB MFFOR-0MB MFFOR-2MB MFFOR-8MB MFFOR-0MB MFFOR-2MB MFFOR-2MB MFFOR-6MB *20MFFOR-20MB90* *Pressure rated at 4000 psi maximum. A B Thread Thread Size Size (In.) (In.) MFFOR-6MB-6MFFOR MFFOR-0MB-0MFFOR Male Flat-Face O-Ring to Male Flat-Face O-Ring on Run Female Flat-Face O-Ring Branch (Tee) A B Thread Thread Size Size (In.) (In.) MFFOR-6FFORX90 Thread Size (In.) MFFOR-4MFFOR-4FFORX 6 6 6MFFOR-6MFFOR-6FFORX 6 6 8MFFOR-8MFFOR-8FFORX 22

222 HYDRAULIC HOSE FITTINGS AND ADAPTERS O-Ring Flange to JIC (7 Flare) Adapters SAE 00R2 Pressure Maximum 90 o 7 o When hose replacement is required, disconnect between adapter and hose coupling. In this way, adapter O-ring seal will not be broken. Attach Female JIC (7 Flare) Swivel Hose Couplings. This permits complete lineup of offset bends resulting in fast and positive replacement in the field without special tools. It also eliminates need for large inventory of costly ready-made hose assemblies. O-Ring Flange to Male JIC (7 Flare) Straight (Code 6 SAE J8) O-Ring Flange to Male JIC (7 Flare) 4 (Code 6 SAE J8) O-Ring Flange to Male JIC (7 Flare) 90 (Code 6 SAE J8) JIC Nom. Male Fig. Head Fig. Size Thread Thickness (In.) (In.) (In.) FL-8MJ FL-2MJ FL-6MJ FL-20MJ FL-24MJ FL-2MJ Flange halves and O-ring if required are to be ordered by part number in addition to adapter. See Flange Half Sets. JIC Nom. Male Fig. Head Fig. Size Thread Thickness (In.) (In.) (In.) FL-8MJ FL-2MJ FL-6MJ FL-20MJ FL-24MJ FL-2MJ4 Flange halves and O-ring if required are to be ordered by part number in addition to adapter. See Flange Half Sets. JIC Nom. Male Fig. Head Fig. Size Thread Thickness (In.) (In.) (In.) FL-8MJ FL-2MJ FL-6MJ FL-20MJ FL-24MJ FL-2MJ90 Flange halves and O-ring if required are to be ordered by part number in addition to adapter. See Flange Half Sets. 222

223 HYDRAULIC HOSE FITTINGS AND ADAPTERS High Pressure Adapter 000 psi Maximum No Braze Joints, Solid One-piece Construction for increased Reliability O-Ring Flange to Male JIC (7 Flare) Straight (Code 6 SAE J8) O-Ring Flange to Male JIC (7 Flare) 4 Bent Tube (Code 6 SAE J8) O-Ring Flange to Male JIC (7 Flare) 90 Bent Tube (Code 6 SAE J8) JIC Nom. Male Fig. Head Fig. Size Thread Thickness (In.) (In.) (In.) FLK-2MJ FLK-2MJ FLK-6MJ FLK-20MJ *20FL4K-6MJ* *20FL4K-20MJ* *Rated at 4000 psi maximum. Flange halves and O-ring if required are to be ordered by part number in addition to adapter. See Flange Half Sets. JIC Nom. Male Fig. Head Fig. Size Thread Thickness (In.) (In.) (In.) FLK-2MJ FLK-6MJ4 Flange halves and O-ring if required are to be ordered by part number in addition to adapter. See Flange Half Sets. JIC Nom. Male Fig. Head Fig. Size Thread Thickness (In.) (In.) (In.) *2FLK-2MJ90* FLK-2MJ FLK-6MJ *20FL4K-6MJ90* *Rated at 4000 psi maximum. Flange halves and O-ring if required are to be ordered by part number in addition to adapter. See Flange Half Sets. High Pressure Adapter 6000 psi Maximum No Braze Joints, Solid One-piece Construction for increased Reliability O-Ring Flange to Male JIC (7 Flare) Straight (Code 62 SAE J8) O-Ring Flange to Male JIC (7 Flare) 4 Bent Tube (Code 62 SAE J8) O-Ring Flange to Male JIC (7 Flare) 90 Bent Tube (Code 62 SAE J8) JIC Nom. Male Fig. Head Fig. Size Thread Thickness (In.) (In.) (In.) FLH6K-2MJ FLH6K-2MJ FLH6K-6MJ FLH6K-20MJ FLH6K-6MJ FLH6K-20MJ FLH6K-24MJ Flange halves and O-ring if required are to be ordered by part number in addition to adapter. See Flange Half Sets. JIC Nom. Male Fig. Head Fig. Size Thread Thickness (In.) (In.) (In.) FLH6K-2MJ FLH6K-6MJ FLH6K-20MJ4 Flange halves and O-ring if required are to be ordered by part number in addition to adapter. See Flange Half Sets. JIC Nom. Male Fig. Head Fig. Size Thread Thickness (In.) (In.) (In.) FLH6K-2MJ FLH6K-6MJ FLH6K-2MJ FLH6K-6MJ FLH6K-20MJ FLH6K-6MJ FLH6K-20MJ90 Flange halves and O-ring if required are to be ordered by part number in addition to adapter. See Flange Half Sets. 22

224 HYDRAULIC HOSE FITTINGS AND ADAPTERS Banjo Fittings with Barbed Connections for Hose or Polyamide Tube Banjo Fittings Seals* Banjo Bolt Hose/ For For Tube Bolt Rubber Polyamide I.D. Size Hose Tube (In.) Metric 46 M0 x R P-2 46 M2 x R P-2 46 M4 x R P-2 46 M6 x R P-2 46 M8 x P-2 6 M2 x R P-2 6 M4 x R P-2 6 M6 x R P-2 6 M8 x R P-2 6 M22 x P-2 86 M4 x P-2 86 M6 x R P-2 86 M8 x R-2 26 M8 x R-2 26 M22 x R P-2 Double Banjo Fittings Hose/ For For Tube Bolt Rubber Polyamide I.D. Size Hose Tube (In.) Metric 86 M8 x R P-2* 46 M0 x R P-2* 46 M2 x R P-2* 6 M4 x R P-2* 86 M6 x R P-2* *Not stocked, special order only. Bonded Seal Cooper Washer Bolt Bonded Copper Size Seal Washer (mm) M M M M M M *Two seals required for Single Banjo. Three seals for Double Banjo. Optional Metric/NPT Adapter Male Female NPTF Metric (In.) Thread 8 M0 x.0 MP M2 x. MP M4 x. MP M6 x. MP 62 4 M8 x. MP 82 4 M22 x. MP 226 Banjo Bolt/Tube Assembly Male Tube Metric O.D. x Wall Thread (In.) M0 x x.00 SBT 0-L M2 x. 6 x.02 SBT 2-L M4 x. 6 8 x.0 SBT 4-L M6 x. 6 2 x.02 SBT 6-L M8 x. 6 8 x.0 SBT 8-L M22 x. 6 4 x.0 SBT 22-L Male Metric Length Hex Thread (mm) (mm) M8 x BJS-08x.0 M0 x BJS-0x.0 M2 x BJS-2x. M4 x BJS-4x. M6 x BJS-6x. M8 x BJS-8x. M22 x BJS-22x. Double Banjo Bolt Male Metric Length Hex Thread (mm) (mm) M0 x DBJS-0x.0 M2 x. 8 7 DBJS-2x. M4 x DBJS-4x. M6 x DBJS-6x. M8 x DBJS-8x. M22 x DBJS-22x. Double Banjo Bolt Assemblies* *Assemblies are available on special order from the Summers Rubber Co. 224

225 HYDRAULIC HOSE FITTINGS AND ADAPTERS Steel Flareless Fittings Reducer Ferrule Body Tube Size Size (In.) (In.) Steel Stainless Steel x 06 x x 06 x x 08 x x 08 x x 08 x x 08 x x 0 x x 0 x x 2 x x 2 x x 2 x x 2 x x 6 x x 6 x x 20 x x 20 x x 24 x x 24 x x 24 x x 24 x 6 Nut Tube O.D. (In.) Steel Stainless Steel 86 76A x x A x x A x x A x x A x x A x x A x x A x x A x x A x x A x x A x x A x x 2 Male Connector Tube O.D. (In.) Steel Stainless Steel x x x 0 77 x x x x 0 77 x x x x x x 0 77 x x 2 77 x x 4 77 x x 6 77 x x x x x x 2 77 x 2 Cap Tube O.D. (In.) Steel Stainless Steel x x x x x x x 0 74 x x 2 74 x x 6 74 x x x 20 Male Tube Pipe O.D. Thread (In.) (In.) Steel Stainless Steel x 02 x x 02 x x 02 x x 02 x x 0 x x 0 x x 04 x x 04 x x 04 x x 04 x x 04 x x 04 x x 04 x x 04 x x 0 x x 0 x x 0 x x 0 x x 06 x x 06 x x 06 x x 06 x x 06 x x 06 x x 06 x x 06 x x 08 x x 08 x x 08 x x 08 x x 08 x x 08 x x 08 x x 08 x x 0 x x 0 x x 0 x x 0 x x 2 x x 2 x x 2 x x 2 x x 4 x x 4 x x 6 x x 6 x x 6 x x 6 x x 20 x x 20 x x 24 x x 24 x x 2 x x 2 x 0 22

226 HYDRAULIC HOSE FITTINGS AND ADAPTERS Steel Flareless Fittings continued Plug Female Connector Tube O.D. (In.) Steel Stainless Steel x x x x x x x x x x x x x x x x 6 Hex Head O-Ring Plug Port Size (In.) No x x x x x x x x x x x x x 2 Hollow Hex O-Ring Plug Note: s furnished with Zinc Dichromate Plating. s are standard without D Option. Port Size (In.) No x x x x x x x x x x x x x 2 Note: s furnished with Zinc Dichromate Plating. Female Tube Pipe O.D. Thread (In.) (In.) Steel Stainless Steel x 02 x x 02 x x 04 x x 04 x x 04 x x 04 x x 0 x x 0 x x 06 x x 06 x x 06 x x 06 x x 08 x x 08 x x 08 x x 08 x x 08 x x 08 x x 0 x x 0 x x 2 x x 2 x x 4 x x 4 x x 6 x x 6 x x 20 x x 20 x 0 Union Tube Tube O.D. O.D. (In.) (In.) Steel Stainless Steel x 02 x 0 77 x 02 x x 0 x 0 77 x 0 x x 04 x 0 77 x 04 x x 0 x 0 77 x 0 x x 06 x 0 77 x 06 x x 06 x x 06 x x 08 x 0 77 x 08 x x 0 x 0 77 x 0 x x 2 x 0 77 x 2 x x 4 x 0 77 x 4 x x 6 x 0 77 x 6 x x 20 x 0 77 x 20 x x 24 x 0 77 x 24 x x 2 x 0 77 x 2 x 0 Large Hex Union Tube Tube O.D. O.D. (In.) (In.) Steel Stainless Steel x x x x x x

227 HYDRAULIC HOSE FITTINGS AND ADAPTERS Steel Flareless Fittings continued Straight Thread O-Ring Male Connector 4 Male Elbow Tube Port O.D. Size (In.) (In.) Steel Stainless Steel x 0 x x 0 x x 04 x x 04 x x 04 x x 04 x x 04 x x 04 x x 0 x x 0 x x 06 x x 06 x x 06 x x 06 x x 08 x x 08 x x 08 x x 08 x x 08 x x 08 x x 0 x x 0 x x 2 x x 2 x x 2 x x 2 x x 6 x x 6 x x 6 x x 6 x x 20 x x 20 x x 24 x x 24 x x 2 x x 2 x 0 Male Tube Pipe O.D. Thread (In.) (In.) Steel Stainless Steel x 04 x x 04 x x 04 x x 04 x x 0 x x 0 x x 06 x x 06 x x 08 x x 08 x x 0 x x 0 x x 2 x x 2 x x 4 x x 4 x x 6 x x 6 x 0 90 Male Elbow Bulkhead Union Tube O.D. (In.) Steel Stainless Steel 6 72 x 0 77 x x x x 0 77 x x x x x x 0 77 x x 2 77 x x 4 77 x x 6 77 x x x 20 4 Elbow Straight Thread O-Ring Tube Port O.D. Size (In.) (In.) No x x x 6 Male Tube Pipe O.D. Thread (In.) (In.) Steel Stainless Steel x 02 x x 02 x x 0 x x 0 x x 04 x x 04 x x 04 x x 04 x x 0 x x 0 x x 0 x x 0 x x 06 x x 06 x x 06 x x 06 x x 06 x x 06 x x 06 x x 06 x x 08 x x 08 x x 08 x x 08 x x 08 x x 08 x x 0 x x 0 x x 0 x x 0 x x 2 x x 2 x x 2 x x 2 x x 4 x x 4 x x 6 x x 6 x x 6 x x 6 x x 20 x x 20 x x 24 x x 24 x x 2 x x 2 x 0 227

228 HYDRAULIC HOSE FITTINGS AND ADAPTERS Steel Flareless Fittings continued 90 Female Elbow 90 Elbow Straight Thread O-Ring Female Tube Pipe O.D. Thread (In.) (In.) Steel Stainless Steel x 04 x x 04 x x 04 x x 04 x x 0 x x 0 x x 06 x x 06 x x 06 x x 06 x x 08 x x 08 x x 08 x x 08 x x 0 x x 0 x x 2 x x 2 x x 4 x x 4 x x 6 x x 6 x 0 Tube Port O.D. Size (In.) (In.) Steel Stainless Steel x x x x x x x x x x x x x x x x 20 Male Branch Tee 90 Union Elbow Tube O.D. (In.) Steel Stainless Steel x x x 0 77 x x x x x x 0 77 x x 2 77 x x 4 77 x x 6 77 x x x 20 Male Tube Pipe O.D. Thread (In.) (In.) Steel Stainless Steel x 04 x 0 x x 04 x 0 x x 04 x 04 x x 04 x 04 x x 0 x 0 x x 0 x 0 x x 06 x 0 x x 06 x 0 x x 08 x 0 x x 08 x 0 x x 08 x 08 x x 08 x 08 x x 0 x 0 x x 0 x 0 x x 2 x 0 x x 2 x 0 x x 4 x 0 x x 4 x 0 x x 6 x 0 x x 6 x 0 x 0 Female Branch Tee Female Tube Pipe O.D. Thread (In.) (In.) Steel Stainless Steel x 04 x 0 x x 04 x 0 x x 04 x 04 x x 04 x 04 x x 06 x 0 x x 06 x 0 x x 08 x 0 x x 08 x 0 x x 0 x 0 x x 0 x 0 x x 2 x 0 x x 2 x 0 x x 6 x 0 x x 6 x 0 x x 20 x 0 x x 20 x 0 x 0 228

229 HYDRAULIC HOSE FITTINGS AND ADAPTERS Steel Flareless Fittings continued Union Tee Male Run Tee Reduced Tube Tube O.D. O.D. (In.) (In.) Steel Stainless Steel x 02 x 0 x x 02 x 0 x x 0 x 04 x x 0 x 0 x x 04 x 0 x x 04 x 0 x x 0 x 0 x x 0 x 0 x x 06 x 06 x x 06 x 0 x x 08 x 0 x x 08 x 0 x x 08 x 08 x x 08 x 08 x x 0 x 0 x x 0 x 0 x x 2 x 0 x x 2 x 0 x x 4 x 0 x x 4 x 0 x x 6 x 0 x x 6 x 0 x 04 Male Tube Pipe O.D. Thread (In.) (In.) Steel Stainless Steel x 04 x 0 x x 04 x 0 x x 04 x 04 x x 04 x 04 x x 0 x 0 x x 0 x 0 x x 06 x 0 x x 06 x 0 x x 08 x 0 x x 08 x 0 x x 08 x 08 x x 08 x 08 x x 0 x 0 x x 0 x 0 x x 2 x 0 x x 2 x 0 x x 6 x 0 x x 6 x 0 x 0 Female Run Tee Straight Thread O-Ring Branch Tee Tube Port O.D. Size (In.) (In.) Steel Stainless Steel x x x x x x 08 Female Tube Pipe O.D. Thread (In.) (In.) No x 04 x 0 x x 04 x 04 x x 06 x 0 x x 08 x 0 x x 0 x 0 x x 2 x 0 x x 4 x 0 x 0 Straight Thread O-Ring Run Tee Bulkhead Nut Tube Port O.D. Size (In.) (In.) Steel Stainless Steel x x x x x x 08 Tube O.D. (In.) Steel Stainless Steel x x x x x x x x x x x x x x x x x x 2 229

230 HYDRAULIC HOSE FITTINGS AND ADAPTERS Steel Flareless Fittings continued Union Cross Tube O.D. (In.) Steel Stainless Steel 4 79 x x x x x x x x x x 2 Hydraulic Steel Tubing Seamless Cold Drawn Carbon Steel Hydraulic Tubing Excellent bending and flaring characteristics Sold in random 20 lengths Tubing Wall Working O.D. Thickness Pressure (in.) (In.) (psi) No , HST , HST , HST 6 0.0,70-0 HST , HST , HST , HST , HST , HST , HST , HST , HST , HST , HST , HST , HST , HST , HST , HST , HST , HST , HST , HST , HST , HST , HST 20

231 HYDRAULIC HOSE FITTINGS AND ADAPTERS Metric Tube Fittings Visual Index Components Bite Ring Coupling Nut Internal Coupling Nut Reinforcing Ring Sealing Washers Hex Nut Peflex Seal Cooper Washer Tube to Tube Couplings Straight Coupling Equal Elbow Equal Tee Equal Cross Bulkhead Connector Bulkhead Elbow Welding Bulkhead Connector Stud Couplings Male Stud Coupling Stud Elbow Stud Barrel Tee Stud Branch Tee Banjos, Swivel Couplings Banjo Conventional Design Banjo Eccentric Channel Design Rotary Coupling Stud/Standpipe Adapter Swivel Elbow Male Stud Type Swivel Branch Tee Male Stud Type Swivel Barrel Tee Male Stud Type Call the Summers Rubber Company for specific sizes and international thread sizes. 2

232 HYDRAULIC HOSE FITTINGS AND ADAPTERS Metric Tube Fittings Visual Index continued Other Standard Couplings Standard/Tube Reducer Male/Female Stud Adapter Gauge Coupling Female Stud Coupling Tube Plug Closure Plug Hex Socket Blanking Plug Welding Boss Weld Nipple With O-ring Seal Non-Return Valve 24 Taper Connections Straight Stud/Standpipe Adapter Adjustable Stud Elbow Adjustable Stud Branch Tee Adjustable Stud Barrel Tee Straight Stud/Standpipe Elbow Adapter Straight Stud/Standpipe Branch Tee Adapter Straight Stud/Standpipe Barrel Tee Adapter Straight Coupling Reducing Coupling Blanking Plug Call the Summers Rubber Company for specific sizes and international thread sizes. 22

233 HYDRAULIC HOSE FITTINGS AND ADAPTERS Voss Metrically Dimensioned Steel Tubing General Application Information Voss metrically dimensioned steel tubing is precision manufactured meeting the requirements of DIN Standard 29, Class C. This tubing is especially well suited for application in hydraulic and pneumatic circuitry where dimensional accuracy and good surface finish are important to the proper attachment of fittings. Workability and Strength Voss steel tubing is annealed prior to delivery and can therefore be coldworked. Prior to bending, the tubing will exhibit the following properties: Tensile strength -4 Kp/mm 2 Yield 24 Kp/mm 2 minimum Bending to close radii will tend to reduce wall thickness at the outer bend and consequently reduce recommended operating pressure. Standard Lengths Voss steel tubes are stocked and shipped in approximately six meter lengths. Tubes of specific cut lengths are available on special order. Conversion Factors millimeter = inch sq. centimeter = 0.0 sq. inch kilogram/sq. centimeter = 4.22 lbs/sq. inch Tube Specifications *Recom-* Nom. Flow mended Size Cross Operating O.D. x Wall Section Pressure (mm) (cm 2 ) (kg/cm 2 ) No. 4 x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x Tube Specifications continued *Recom-* Nom. Flow mended Size Cross Operating O.D. x Wall Section Pressure (mm) (cm 2 ) (kg/cm 2 ) No. 28 x x x x x x x x x x x x x x x x x x x x x x *Based on 4 to safety factor. For availability of sizes not listed, special cross section shapes, and special materials, contact the Summers Rubber Company. 2

234 HYDRAULIC HOSE FITTINGS AND ADAPTERS Voss Micro Hose Assemblies Pressure Test Systems Micro Hose Specifications: Operating temperature range: -40 F to 22 F (-40 C to 00 C) Standard color: Black Materials: Outer cover Nylon Inner core Nylon Reinforcement Kevlar 24

235 HYDRAULIC HOSE FITTINGS AND ADAPTERS SAE Four Bolt Connections Pipe Thread Fitting Pipe Thread O-Ring Fitting Pipe Pad Size Size A B C D (In.) (In.) (In.) (In.) (In.) (In.) W W W W W W W W W W W W Pipe Pad A B Size Size ±.0 ±.0 C D (In.) (In.) (In.) (In.) (In.) (In.) W W W W W W W SAE Internal Straight Thread O-Ring Fitting SAE Boss Tube Pad A B C D Dash Size Size ± 2 ± 2 ±.00 ±.00 No. (In.) (In.) (In.) (In.) (In.) (In.) W W W SAE Flanges Flat Socket O-Ring Weld Fittings 000 psi Working Pressure Pipe to SAE Four Bolt Connection Pipe Pad Size Size A B C D (In.) (In.) (In.) (In.) (In.) (In.) W W W W W W W W W W Tube to SAE Four Bolt Connection Pipe Pad Size Size A B C D (In.) (In.) (In.) (In.) (In.) (In.) W W W W W W W W W W

236 HYDRAULIC HOSE FITTINGS AND ADAPTERS Flat Socket Weld Fittings 000 psi Working Pressure SAE Flanges The socket weld fitting is used to connect a pipe end to a SAE four bolt flange connection. They are designed to be welded on the end of a pipe or tube. Weld fittings are made from SAE C08 steel which offers fine weld characteristics. Design and dimension specifications subject to change without notice. Pipe to SAE Four Bolt Connection Pipe Pad Size Size A B C D (In.) (In.) (In.) (In.) (In.) (In.) W W W W W W W W Tube to SAE Four Bolt Connection Pipe Pad Size Size A B C D (In.) (In.) (In.) (In.) (In.) (In.) W W W W W W W W W Forged SAE Flange Adapters and Accessories Series psi Flange A B D E G Thread Size (In.) (In.) (In.) (In.) (In.) JFC JFC JFC JFC JFC Series psi Flange A B D E G Thread Size (In.) (In.) (In.) (In.) (In.) JFC JFC JFC JFC JFC

237 HYDRAULIC HOSE FITTINGS AND ADAPTERS Forged SAE Flange Adapters and Accessories continued SAE Flanges Series 6 / psi Flange A B D E G Thread Size (In.) (In.) (In.) (In.) (In.) JFC JFC JFC JFC JFC Series 62 / psi Flange A B D E G Thread Size (In.) (In.) (In.) (In.) (In.) JFC JFC JFC JFC JFC O-Ring Flange Fitting Accessories Flange Half Sets Code 6 SAE J8 Flange Half Sets Code 62 SAE J8 Nom. Flange Dia. Sets/ Size A B STD (In.) (In.) (In.) (Pack) SF SF SF SF SF SF SF SF SF SF Each set contains: 2 flange halves, O-ring, 4 bolts and 4 lockwashers. Nom. Flange Dia. Sets/ Size A B STD (In.) (In.) (In.) (Pack) SFX SFX SFX SFX SFX SFX Each set contains: 2 flange halves, O-ring, 4 bolts and 4 lockwashers. 27

238 HYDRAULIC HOSE FITTINGS AND ADAPTERS O-Rings for Code 6, Code 62 and Caterpillar Style Flange Fittings O-Rings I.D. Wall Qty. (In.) (In.) Req d FLOR 8 0FLOR 8 2FLOR 8 6FLOR 8 20FLOR 8 24FLOR 8 2FLOR 8 40FLOR 8 48FLOR 8 6FLOR 8 64FLOR Caution: These O-rings are compounded from a Nitrile polymer for use with petroleum-based hydraulic fluids, water and glycol and oil-water emulsions. Do not use these O-rings with phosphate esters, diesters or phosphate ester emulsion hydraulic fluids. Instead, use O-rings made of Viton, EPDM or CPE polymers or other materials compatible with the fluids. Viton is a registered trademark of the DuPont Co. S Series In-line Swivel Joint High Pressure Hydraulic Swivel Joints 9S Series 90 Swivel Joint Sizes: 4 through 2 pipe size. Connection types: JIC, pipe, SAE O-ring face seal Connection types: (male and female). Operating pressures: Vacuum and to 000 psi. Operating temperatures: 40 F to 200 F (4 C to 9 C). 000 psi/ Full Flow Female Pipe to Male Pipe Sizes: 4 through 2 pipe size. Connection types: JIC and O-ring (male), pipe and Connection types: SAE O-ring face seal (male and female) Connection types: and pipe union. Operating pressures: Vacuum and to 000 psi. Operating temperatures: 40 F to 200 F (4 C to 9 C). 000 psi/ Pressure Balanced Female Pipe Union to Male Pipe Barrel Stem Barrel Stem Thread Thread Nom. Size Nom. Size (In.) (In.) (In.) (In.) S6PF4-P S6PF6-P S8PF8-P S8PF2-P S6PF6-P S20PF20-P S24PF24-P S2PF2-P2 Swivel Joints Barrel Stem Barrel Stem Thread Thread Nom. Size Nom. Size (In.) (In.) (In.) (In.) S6PU4-P S6PU4-P S6PU6-P S6PU6-P S8PU8-P S2PU2-P S6PU6-P S20PU20-P S24PU24-P S2PU2-P2 28

239 HYDRAULIC HOSE FITTINGS AND ADAPTERS High Pressure Hydraulic Swivel Joints continued 9SS Series Dual Plane Swivel Joint 8S Series 80 Swivel Joint Sizes: 4 through 4 pipe size. Connection types: JIC and O-ring (male), pipe and Connection types: SAE O-ring face seal (male and female). Operating pressures: Vacuum and to 000 psi. Operating temperatures: 40 F to 200 F (4 C to 9 C). Swivel Joints Sizes: 4 through 2 pipe size. Connection types: JIC (male), pipe and SAE O-ring face Connection types: seal (male and female) and pipe union. Operating pressures: Vacuum and to 000 psi. Operating temperatures: 40 F to 200 F (4 C to 9 C). Fluid Conducting Swivels Barrel/Stem Number System Example: 9S6PF6-PF6* 9S 6 PF 6 PF 6 * Body Configuration S In-line 9S 90 9SS Dual plane 8S 80 Body Size ( 8 ) Nominal bore in 6 increments Size ( 8 ) Special Seal Compound Number Flurocarbon (Viton) Rubber 7 Ethylene Propylene 9 Neoprene Others on request. Connector Type PF Female Pipe NPTF P Male Pipe NPTF J Male JIC O Male SAE O-ring PU Pipe Union NPSM F Male SAE O-ring Face Seal FF Female O-ring Face Seal Size ( 8 ) Connector Type (Typical) Barrel Configuration Stem Configuration 29

240 HYDRAULIC HOSE FITTINGS AND ADAPTERS Power Crimp Equipment and Hose Protection Products Power Crimp 707 The Gates Power Crimp 707 is the most precise, yet simplest crimper made. Crimps hydraulic hoses from low pressure return lines to extremely high pressure spirals, from 6 to 4 I.D. Crimps straight and bent tube stems, plus 4 and 90 block types. OmniCrimp 2 Horizontal Front-End Feed makes crimping easier and convenient. Large hoses with 90 bent tubes and flanges load without removing the dies. Crimping sizes from /6 to 2 ; six spiral wire hose with all coupling configurations. Plated Wire Spring Guards A (In.) G P (Tol..0) (In.) (In.) No..0 4 (.080) (.080) (.06) Close Wound (.080) (.080) (.080) (.080) (.080) (.080) (.20) (.20) (.20) (.20) (.080) (.080) (.20) (.20) A Pitch P G Gauge Wire MobileCrimp 4-20 The latest in high-tech crimping. Portable (mobile) crimper is light, versatile and powerful enough to crimp up to /4 four-spiral hose. Features: Digital accuracy for precise, consistent crimping. Portable (7 pounds) or can be mounted permanently on service vehicle or work bench. Flexible Hose Bend Restrictor Protects Hose Near the Coupling Tapered PVC sleeve reduces bending stress in the hose near the coupling to prevent damage, such as in power wash applications. Installed during hose asssembly, this smoothlyfinished product withstands temperatures from -40 F to 200 F (-40 C to 9 C) and is available in six I.D. sizes. I.D. Length (In.) (In.) No... HBR-0.6. HBR HBR HBR HBR HBR-0 Power Crimp and OmniCrimp are registered trademarks and MobileCrimp is a trademark of Gates Rubber Company. Nylon Protective Sleeve Solves Abrasion Problems Nylon Sleeves perform a dual role: () they provide excellent abrasion resistance to protect individual hoses; and (2) they can be used to bundle several hose assemblies together for maximum protection. Downtime and maintenance costs are reduced. These Nylon Sleeves are unique because they form an extra protective layer against abrasive forces. Specifically, thousands of tiny nylon filaments, woven into the texturized yarn, friz into a selfrenewing shield that is extremely resistant to severe abrasion. Inside Sleeve Flat I.D. A B (In.) (In.) Color No Black HG Black HG Black HG Black HG Black HG Black HG Black HG Black HG Black HG Black HG Black * Black * Black * Black * Black * Black * *Sleeving has 0.80 flat thickness (double). Nonstock. Check for availability. 240

241 GASKETS AND SEALING PRODUCTS Mechanical Seals X-00 Dura Seal SL-000 Dura Seal HSC/HSH/HSI Dura Seal Single, metal bellows design eliminates shaft packing hang-up and shaft or sleeve fretting. Very good in abrasive services. Incorporates Durametallic s patented Face Attachment technology to increase seal life. Pre-set cartridge simplifies installation, eliminates guesswork. Can easily be converted to a double or tandem seal using interchangeable components. Type of seal: Single, bellows design. Pressure: To 00 psig. Temperature: To 400 F (204 C). Velocity: To 4,00 fpm. Standard sizes: 8 to 4 2. P-0 Dura Seal Versatile, cartridge, single, pusher seal specifically designed for abrasive slurry services. Unique design exposes seal faces to pumped product for maximum heat dissipation eliminates a common failure point. Special shroud protects compression springs in stationary portion of seal, and rotor drive pin, from weepage build-up. Pre-set cartridge design and centering tabs simplify installation. Type of seal: Single, pusher design. Pressure: To 20 psig. Temperature: To 0 F (77 C). Velocity: To 2,800 fpm. Standard sizes: 8 to 6. PSS Dura Seal Single, pusher seals designed for use in high pressure and speed applications. Compression springs are mounted on stationary portion of seal to isolate them from centrifugal forces and high pressures. Throttle bushing provides safety back-up in the event of primary seal failure. HSC and HSH designs are boundary lubricated, HSI is full fluid film lubricated. Heavy-duty construction for long life. Type of seal: Single, pusher design. Pressure: HSC, HSH To,200 psig. Pressure: HSI To,000 psig. Temperature: HSC, HSH To 400 F (204 C). HSI To 600 F (6 C). Velocity: All To 2,00 fpm. Standard sizes: 2 to 0. PBR/PBS Dura Seal Single, pusher seal excellent for numerous services in chemical processing, water treatment and sewage plants, and pulp and paper mills. Pre-set cartridge design speeds installation, eliminates chance of installation error. Very easy to repair, too. Springs are mounted on stationary portion of seal to forgive seal misalignment and face eccentricity. Off-the-shelf availability to fit standard ANSI pump sizes. Type of seal: Single, pusher design. Pressure: To 00 psig. Temperature: To 00 F (0 C). Velocity: To,000 fpm. Standard sizes: to 4. Split, single inside seal used in applications where installation involves time consuming equipment teardown or is cost prohibitive. Pre-assembled, unitized construction makes installation and repair easy and foolproof. Installs in under 0 minutes. Excellent for numerous non-hazardous services in chemical processing, pulp and paper, power generation, wastewater treatment and refineries. Type of seal: Split, single pusher Type of seal: design. Pressure: To 00 psig. Temperature: To 20 F (2 C). Velocity: To,200 fpm. Standard sizes: 2 to 6. Single, inside bellows design specifically for use in high temperature applications in the petroleum industry. PBR design has a rotating bellows assembly, PBS is stationary. Advanced face attachment permits thermal expansion without distortion of seal face. Seal faces are also easily replaced. Patented tapered insert ensures correct installation of insert mounting. Type of seal: Single, bellows design. Pressure: To 0 psig. Temperature: To 70 F (400 C). Velocity: PBR To 4,00 fpm. Velocity: PBS To 6,00 fpm. Standard sizes: 8 to

242 GASKETS AND SEALING PRODUCTS Mechanical Seals continued CBR/CBS Dura Seal PTO/PTO-E/PTO-HW Dura Seal TBR Dura Seal Single, metal bellows design eliminates shaft packing hang-up and fretting. Seal ring is easily and economically replaced. Patented Centroid Loaded Face Attachment increases seal life by preventing seal face distortion caused by different thermal expansion rates of the face and holder materials. Excellent in slurry services. Cartridge design available to simplify installation and maintenance. Standardized insert fits most ANSI pumps. Type of seal: Single, bellows design. Pressure: To 00 psig. Temperature: To 400 F (204 C). Velocity: CBR To 4,00 fpm. Velocity: CBS To 6,00 fpm. Standard sizes: 4 to 2. RA/RA-C Dura Seal Balanced, single, pusher seal best suited to moderate pressure applications. Can accommodate different types of shaft packing interchangeably. Often used in condensate and multi-stage boiler feed pumps. PTO-E version includes custom-designed face for use with light hydrocarbons with specific gravities less than heptane. PTO-HW version incorporates special hydraulic balancing for use in hot water applications. No cooling system required. Type of seal: Single, pusher design. Pressure: To 600 psig. Temperature: PTO, PTO-E To 20 F (2 C). PTO-HW To 0 F (80 C). Velocity: To 4,00 fpm. Standard sizes: 4 to 4 2. Single, outside bellows seal designed for use in corrosive chemical services. Special PTFE bellows assembly resists chemical attack and is bonded to the seal face and collar ends. Replaceable faces can be carbon, silicon carbide or glass-filled Duraflon. Type of seal: Single, bellows design. Pressure: To 7 psig. Temperature: To 60 F (7 C). Velocity: To 4,00 fpm. Standard sizes: to. SB-200 Dura Seal RO Dura Seal Single, outside pusher seal used in applications where pressures above psig eliminates usage of the RO Dura Seal. The RA version incorporates a two-piece rotary unit consisting of a collar and seal ring. The RA-C version is designed for use with chemical products in plastic, glass and other non-metallic pumps. Both are very easily repaired if necessary. Type of seal: Single, pusher design. Pressure: To 400 psig. Temperature: To 0 F (77 C). Velocity: To 4,00 fpm. Standard sizes: 2 to. 242 Economical single, unbalanced seal that can be used for hundreds of applications. Individual parts are completely interchangeable and easy to replace. Lets you customize seal to your service and cuts down on maintenance costs. Can be used as an inside or outside seal. Good performer in tough abrasive and corrosive services, too. Type of seal: Single, pusher design. Pressure: To 00 psig. Temperature: To 00 F (260 C). Velocity: To 4,00 fpm. Standard sizes: 8 to 4 2. Unique back-up seal designed for use in a tandem configuration with a single pusher or bellows seal. Used to stop VOCs leaking past the primary seal and vent them to a vapor recovery system. Qualifies for EPA reporting exemption. Seal incorporates special self-lubricating seal face combination. Will operate in back-up mode for at least two weeks in event of primary seal failure. Type of seal: Tandem design. Pressure: Dry To 0 psig. Pressure: Wet To 00 psig. Temperature: To 00 F (0 C). Velocity: To 2,000 fpm. Standard sizes: 4 to 4 4. Duraflon is a registered trademark of Durametallic Corp.

243 GASKETS AND SEALING PRODUCTS Mechanical Seals continued MX-20 Dura Seal VRA Dura Seal Tandem PTO/PTO-E Dura Seal Double, pusher design used in mixer applications where no leakage can be tolerated. Able to handle system upsets without leakage or product contamination. Offers greater safety and reliability than possible with conventional double seals. Can be run wet or dry, or in tandem configuration, for added versatility and economy. Preset cartridge canister design eliminates need for setting measurements. Type of seal: Double, pusher seal. Pressure: Double, wet To 00 psig. Pressure: Double, dry To psig. Pressure: Tandem, wet and dry Pressure: To 00 psig. Temperature: To 00 F (0 C). Velocity: Wet To 20 fpm. Velocity: Dry To 0 fpm. Standard sizes: 6 to 6 6. Single, outside, dry-running pusher seal designed specifically for use in top-entry agitator/mixer services. Seal features heavy-duty construction to accommodate a combined out-of concentricity and eccentricity of 0.0 F.I.M. Milled slots and mating pins in the drive collar evenly distribute torque to the faces, eliminating stress areas. Dry-running design eliminates need for buffer fluid system. Type of seal: Single, pusher seal Type of seal: (double available). Pressure: To 200 psig. Temperature: To 20 F (2 C). Velocity: To 00 fpm. Standard sizes: to 7. BRO/BPO Dura Seal Two single balanced pusher seals arranged in series configuration. Typically used as a safety seal or to meet today s stringent emissions control standards. As with the single PTO, different types of shaft packing are available and interchangeable. For fluids with a specific gravity less than heptane, custom designed faces (PTO-E version) can be used. Type of seal: Tandem, pusher design, Type of seal: series configuration. Pressure: To 600 psig. Temperature: To 20 F (2 C). Velocity: To 4,00 fpm. Standard sizes: 4 to 4 2. SL-200 Dura Seal X-200 Dura Seal Cartridge mounted, double metal bellows seal ideal for use in mild abrasive services where the added security of a double seal is necessary. Bellows design eliminates shaft packing hang-up and fretting. Patented bidirectional flow inducer aids in proper cooling, extending seal life. Can operate as a tandem configuration. Tolerates pressure reversals. Type of seal: Double, bellows design. Pressure: To 200 psig. Temperature: To 400 F (204 C). Velocity: To 4,00 fpm. Standard sizes: 8 to 4 8. Single, pusher seals designed for use on large shaft mixers, blenders and similar units. Overcomes shaft deflection problems common to this type of equipment. Carbon seal ring designed to float within the shroud follows deflection of the shaft. Incorporates elastomer secondary seal for resistance to chemical attack. BPO Dura Seal is a balanced design to accommodate higher pressures. Type of seal: Single, pusher seal Type of seal: (double available). Pressure: BRO To 200 psig. Pressure: BPO To 400 psig. Temperature: To 20 F (2 C). Velocity: To,00 fpm. Standard sizes: 4 to 2. Double, pusher seal used in very abrasive applications where corrosive, toxic or volatile liquids are being handled and single seal is not acceptable. Inner and outer seal faces are interchangeable. Outer seal is shrouded by gland as added safety feature. No bypass or external flush needed. Tolerates pressure reversals. Cartridge design simplifies installation. Type of seal: Double, pusher design. Pressure: To 20 psig. Temperature: To 0 F (77 C). Velocity: To 2,800 fpm. Standard sizes: 8 to 6. 24

244 GASKETS AND SEALING PRODUCTS Mechanical Seals continued MSS Dura Seal GB-200 Dura Seal Double RO Dura Seal Split, single outside seal designed for use on large, heavy or inaccessible equipment where seal changeout is costly or prohibitive. Split design facilitates installation without dismantling equipment. Self-lubricating faces dissipate heat and can run dry. Also, withstands pressure reversals common to agitator services. Very easy to install and maintain. Handles shaft run-out up to 0.0 F.I.M. Type of seal: Split, pusher design. Pressure: Wet To 00 psig. Pressure: Dry To 7 psig. Temperature: To 20 F (2 C). Velocity: Wet To 2,200 fpm. Velocity: Dry To 0 fpm. Standard sizes: to 2. Double, pusher design used in applications where no emissions of hazardous pumped product can be tolerated. Seal uses inert gas barrier, such as nitrogen or clean shop air, for lubrication. Eliminates contamination of pumped product by a buffer fluid. Provides total containment, even if outer seal fails. Extremely reliable and economical alternative to sealless pump. Type of seal: Double, pusher design. Pressure: To 200 psig. Temperature: To 20 F (2 C). Velocity: To 2,600 fpm. Standard sizes: to 2 4. P-200 Dura Seal Double, pusher design recommended in applications where pumped liquid has greater lubricating properties than water, pressures exceed the limitations of the double CRO Dura Seal, or the fluid is abrasive. Positive drive design. Metal parts of seal are isolated from pumped product to prevent possible chemical or abrasive attack. Type of seal: Double, pusher design. Pressure: To 00 psig. Temperature: To 00 F (260 C). Velocity: To 4,00 fpm. Standard sizes: 4 to 4 2. Double CRO Dura Seal Economical, cartridge mounted, double pusher design combines value with ease of installation. Its unitized construction and balanced design make the P-200 an ideal choice for a wide range of demanding services in general industry including chemical processing, pulp and paper, water treatment, and sewage plant applications. Type of seal: Double, pusher design. Pressure: To 400 psig. Temperature: To 40 F (2 C). Velocity: To 4,00 fpm. Standard sizes: to 7 8. Double, pusher seal used in moderate pressure applications where water, or a liquid with similar lubricating properties, can be used as a sealing fluid. Seal depends on friction between shaft packing and pump shaft for drive. Fluids with lubricating properties greater than water must not be used. Very easy to install since no dimensional setting or drive collar is required. Type of seal: Double, pusher design. Pressure: To 00 psig. Temperature: To 20 F (49 C). Velocity: To 4,00 fpm. Standard sizes: 8 to

245 GASKETS AND SEALING PRODUCTS Accessories to Maximize Sealing Performance and Longevity Supply Tanks Durametallic Supply Tanks are the main ingredient of a closed-loop buffer fluid supply system for use with tandem or double sealing systems. They dramatically cut seal flush water usage and eliminate the need to run water lines from a distant source. They can indicate the condition of inner seal in double seal arrangement. With alarm options, it can monitor sealing performance. Easy to install and maintain. Dura Circulator The Dura Circulator supplies a controlled volume of sealing liquid at uniform pressure and temperature to stuffing boxes containing double Dura Seals. It is available in a variety of basic units for various pressures and capacities. Nominal capacities range from -4 gpm, while pressure varies from 0-2,000 psig. Metric units are also available. Dura Airfin Cooler The Dura Airfin Cooler reduces temperatures surrounding a mechanical seal without using cooling water. The Airfin Cooler offers substantial savings in flush water purchase and treatment. It is less susceptible to fouling, more efficient and requires less piping than a water flush system. Plus, it s easy to install and maintain. Model 62NC natural convention of air over the coil for cooling. Model 62FC forced air by an efficient hp electric motor. Bearing Gard Eliminates bearing failures due to lubricant contamination. Close-tolerance labyrinth design locks out moisture, grit and dust. Allows bearing frame pressure vents (a common point of contamination) to be plugged. Lasts for the life of the pump and fits existing lip seal cavities. Unitized construction for error-proof installation. Recommended for use on all process pumps and other rotating equipment. Numerous sizes available. BGM Bearing Protector Like Bearing Gard, BGM keeps contaminates from ruining bearings. Utilizes rare earth magnets to seal off bearing housing completely. Often used in outdoor or other applications where absolutely no humidity, dirt or dust can be tolerated. Patented coaxial face design ensures long life. Very easy to install. Lasts up to 2 times longer than lip seals. Numerous sizes available. Dura Heat Exchanger Heat exchanger provides an effective way to cool Dura Seals. Flow of the pumped product through the heat exchanger can be induced with a bypass line from the pump discharge, or with a special Dura Circulating feature. Compact and lightweight. Features a one-piece 8 O.D. stainless steel cooling coil hydrostatically tested at,000 psig. Cover is easily removed for coil cleaning. Stainless steel construction for maximum corrosion resistance. Zytel is a registered trademark of the DuPont Co. Dura Circulator, Dura Airfin Cooler, Dura Heat Exchanger and Duraflon are registered trademarks and Bearing Gard is a trademark of Durametallic Corp. Dura Dirt Diverter The Dura Dirt Diverter is a cyclone separator that is used to remove abrasive solids in suspension that have a specific gravity greater than the pumped liquid. It is well suited to systems where the product is circulated only once through the pump before continuing on to other processes. It is not a filter. Therefore, it will not clog. Model -DD alloy metal, suitable for corrosive liquids. Model 2 Zytel lined with ceramic for abrasion resistance. Dura Lip Seal Dura Lip Seal is used to prevent abrasive solids from entering the stuffing box and reaching the Dura Seal. It is a throat restriction device that creates high velocities at the throat of a pump with a minimal amount of flushing liquid flow and product dilution. Held firmly in place at bottom of seal chamber by split metal expansion collar. Split Flow Reducer Lowers seal water flush (API Plan 2) requirements when used with a Dura Seal by replacing packing in the seal chamber with an engineered, close clearance device. Split axially for ease of installation. Constructed of glass-filled Duraflon for corrosion and abrasion resistance. 24

246 GASKETS AND SEALING PRODUCTS Compressed Gasket Material KLINGER Flexible Graphite SLS * Graphite adhesive bonded to a stainless steel foil. Highly compressible and compactible. Excellent anti-stick properties. Low gas permeability. Low electrical resistance. *available with anti-stick coating. KLINGER sil C-7400 Synthetic fiber. EPDM binder. Moderate caustics and acids. Good oil swell characteristics. Excellent aging properties. Good in steam. KLINGER sil C-44 Fiberglass, Aramid and inorganic fibers. Nitrile binder. Ultimate steam sheet. Outstanding load bearing. Excellent creep relaxation. Best general purpose sheet. Exceeds API Fire Test. KLINGER sil C-440 Synthetic fiber. Nitrile binder. Excellent sealability. Excellent chemical resistance. Good creep relaxation. Good general purpose sheet. Comparable to Garlock Blue Guard. KLINGERsil is a registered trademark of Richard Klinger Inc. and Teflon is a registered trademark of the DuPont Co. 246 KLINGER sil C-400 Synthetic fiber. Nitrile binder. Economical. Good sealability. General purpose sheet. Suitable for a wide range of chemical applications. KLINGER sil Expanded Metal Reinforced C-449 Fiberglass, aramid and inorganic fibers. Nitrile binder. High temperature and stress. Vibration. Galvanzied low carbon steel insert. KLINGER sil C-6400 Synthetic fiber. SBR binder. Good anti-stick properties. Good steam sheet. KLINGER sil C-8200 Synthetic fiber. Hypalon binder. Acid resistant. Good oil-fuel resistance. Good gas sealability. No color added. Standard Sheet Size: 60 x 60. chem-2000 PTFE (Teflon ) Sheet Standard Sheet Dimensions: Sheet size: x ±2 Thicknesses:.0 ;.040,.060, Thicknesses:.080,.8 ±0% Thickness Tolerances to ASTM F04 Nominal Standard Range Thickness of Thickness (In.) (In.) (In.) (In.)

247 GASKETS AND SEALING PRODUCTS Cut Rubber and Gasket Material s for Industrial Applications Available from belting, rubber sheeting and flat materials. Die rule and water jet cutting, stripping and custom forms. Cut Rubber s Belting, Rubber Roll Goods and Stripping Range of Materials: Varieties of industrial conveyor belting: Rubber both sides Fabric both sides Combinations of rubber and fabric High heat resistance Oil resistant Oil proof Cross-rigid Textured surfaces or with profiles Varieties of food grade lighter duty conveyor belting: White rubber White Nitrile White PVC RMV blends of vinyl Textured surfaces or with profiles Unsupported (without fabric insertion) rubber sheeting: Neoprene Nitrile Silicone SBR Natural gum rubber Skirt board rubber Rhino Hide and chute lining Crude spongex open cell structure Closed cell neoprene sponge sheets and buns Urethane Butyl Vinyl UHMW plates, boards and sheeting Coated fabrics (fabric supported sheet): Diaphragm materials Cloth inserted (C.I.) sheet Plied cross-rigid belt and sheet Roll-up door fabric and sheet Pressure sensitive adhesive (PSA) backed materials. Expanded metal back rubber polymers. 247

248 GASKETS AND SEALING PRODUCTS Summers Rubber Sealing Technical Service Company Name Person to Contact Telephone No. Fax No. If you would like us to advise you on your gasket application, please provide the details requested below and fax the form to: Duty Medium Gasket Details (dimensions). Full Face Concentration Outside Diameter Max. Pressure Max. Temperature Liquid or Gas Any other comments (cycling, vibrations, food, hazardous) Flanges Rating Nominal Size Flange Material Inside Diameter Number of Holes Hole Diameter or 2. Ring Outside Diameter Inside Diameter or. Special Design Please provide drawing. Surface Finish Type If non-standard, please give dimensions Bolts Quality Diameter/Length Number Current application material and thickness. Reason for material change (i.e. leaks, blow out) Photocopy this form for re-use. 248

249 GASKETS AND SEALING PRODUCTS Reliable Gasketing on a Roll Sealex Easy to use Sealex Follow the simple installation instructions:. Make sure that the sealing flanges are clean and free from rust, dirt and gasket debris. Clean flange face as usual. 00% Pure PTFE which has been expanded by a special process to form soft, highly compressible gasketing on a roll. It has the very wide chemical resistance of PTFE and a pressure sensitive adhesive strip to ensure easy installation. Maximum operating conditions: Temperature 00 F. Pressure 2000 psi. (Note these figures do not operate at the same time.) Unlike conventional PTFE, which is prone to cold flow, Sealex has good creep resistance and bolt torque retention properties. Highly compressible suitable for sealing weak or damaged flanges. Wide chemical resistance range inert to practically all chemicals. Available in roll form no need to maintain large stocks of gaskets. Not subject to aging PTFE is unaffected by normal environmental conditions. Suitable for cryogenic use -2 F (-96 C). Ideal for use where cleanliness is essential will not support bacterial growth or contaminate product being sealed. Sealing surfaces part freely saves expensive maintenance downtime. FDA compliance. Easy to assemble. Sealex is a registered trademark of Richard Klinger Inc. More reliable the high compressibility of Sealex joint sealant produces a very thin, wide ribbon under pressure. This means that the smallest possible area is exposed to liquids and gases. In this condition, the thin film of Sealex is no longer subject to significant cold flow. You can bolt up once and not have to retorque later. Fume ducts. Concrete lids. * Glass joints. Heat exchangers. Fiberglass reinforced plastic vessels. Pump or compressor housing flanges. Steam vessel flanges. Manways. * Ceramic joints. Hydraulic and pneumatic systems. Water systems. Or practically any other industrial equipment where you require a long life, trouble-free seal that cuts maintenance costs Sealex Standard Spool Lengths Regular Jumbo Size Spools Spools (In.) Ft./Spool Ft./Spool 84 00, , , ,20 22,0 86, , ,80 Other spool lengths can be reeled to customer order. 2. Cut off a length of Sealex just a little longer than the actual circumference of the perimeter of the seal.. Peel off the adhesive protection strip and press the Sealex into position. Cross the free ends of the Sealex adjacent to a bolt hole. 4. Bolt up the mating surfaces using the recommended clamping force and bolt tightening patterns. 249

250 GASKETS AND SEALING PRODUCTS Braided Compression Packing Flax Aramid Teflon Carbon/Graphite RM 22 General service marine packing; also offered with a special graphite waterproof compound lubricant for use in high pressure hydraulic service. Service temperature: to 20 F (99 C). Service pressure: to 00 psi. Surface speed: to,000 fpm. RM 94 Clean, high temperature resistant packing. Braided Flextra impregnated with PTFE, plus break-in lubricant. Also filament Kevlar. Service temperature: to 00 F (260 C). Service pressure: to 00 psi. Surface speed: to 2,20 fpm. RM 847, RM 847FDA* Braided PTFE filament impregnated with a high concentration of PTFE suspensoid; also offered with a FDA approved lubricant. Service temperature: to 00 F (260 C). Service pressure: to 200 psi. Surface speed: to 2,200 fpm. RM 862 Braided, high purity carbon. Can also be impregnated with PTFE or finely powdered inorganic graphite. Service temperature: to -200 F (-9 C). to Steam 200 F (6 C). Service pressure: pumps to 00 psi. Surface speed: to 4,000 fpm. Synthetic Teflon/Graphite Expanded PTFE/Graphite Papermill/ Caustic High Performance Synthetic RM 94 Multiservice acrylic yarns impregnated with PTFE or graphite and treated with a break-in lubricant. Service temperature: to 00 F (260 C). Service pressure: to 00 psi. Surface speed: to,00 fpm. 20 RM 844* GFO yarns with Flextra corners. Also available with 00% braided GFO graphite filled expanded PTFE yarns. Service temperature: to 00 F (260 C). Service pressure: to 600 psi. Surface speed: to,600 fpm. Teflon is a registered trademark and Kevlar is a trademark of DuPont Co.; GFO is a trademark of the W.I. Gore Associates and Flextra is a trademark of RM Engineered Products. RM 94 Braided yarns of high technology fibers, impregnated with PTFE dispersion; ideal for high caustic levels seen in pulp and paper and chemical processes. Service temperature: to 40 F (22 C). Service pressure: to 00 psi. Surface speed: to 2,000 fpm. RM 980 Outstanding general purpose pump packing; braided Novaloid yarn, PTFE impregnated with special break-in lubricant. Service temperature: to 480 F (20 C). Service pressure: to 00 psi. Surface speed: to 2,200 fpm. *See next page for details.

251 GASKETS AND SEALING PRODUCTS Flange and Valve Shields Advance Products & Systems, Inc. designs and manufactures spray shields to inhibit dangerous leaks of hazardous high-temperature materials. The shields are effective in reducing damage to surrounding equipment and injuries to plant personnel. Inspection costs, repairs and resulting downtime are also reduced due to leak containment through the use of shields. Flange Shields Metal Metal shields are manufactured from 24 gauge sheet metal with 00% stainless steel, quick coupling wormgear and screw connections for easy installation. Stainless steel: Available in 04 and 6 grades Stainless Steel. Max. operating temperature 2000 F. Max. operating pressure,00 psi. Sizes 2 to 48 pipe diameter. 0# ANSI to 200# ANSI. Galvanized steel: Max. operating temperature 800 F. Sizes 4 to 48 pipe diameter. 0# ANSI to 200# ANSI. Both types of metal shields can be manufactured with anti-mist screens. Drain shields are also available. These are similar to the metal shields except that there is a stainless steel nipple attached to the bottom of the shield to allow for drainage of any leaks. Drain shields are also caulked around the nipple and the sides are seal welded. Cloth Plastic cloth shields are manufactured of clear reinforced cloth for easy visibility or a UV stabilized colored cloth which is resistant to sun, rain and fumes. They include the standard ph leak indicating patches on the colored shields. Teflon : Teflon coated glass cloth. Teflon thread and drawstring. ph leak indicating patch. Max. operating temperature 40 F. Sizes 4 to 6 pipe diameter. 0# ANSI to 00# ANSI. Polyvinyl, Polyethylene, Saran : Max. operating temperature 70 F. Sizes 4 to 6 pipe diameter. 0# ANSI to 00# ANSI. Polypropylene: Max. operating temperature 200 F. Sizes 4 to 6 pipe diameter. 0# ANSI to 00# ANSI. Expansion Joint Shields An especially critical area for use of shields is on expansion joints. The major manufacturers of Teflon lined expansion joints recommend the use of spray shields with their products. Warnings requiring their use are printed on their boxes for the expansion joints and in their product brochures. Advance expansion joint shields are manufactured of only Teflon. Valve Shields Valve shields are manufactured to fit all types of valves including butterfly, globe, check, gate, ball and plug. These shields are available in the same cloth or metal materials and a complete range of sizes as our full line of other shielding products. Specialty Shields Other specialty shields are available for screw-pipe fittings including unions, couplings, elbows and tees. How to Order: Metal Shields For Valves, please specify:. Pipe size. 2. Type of valve and manufacturer.. Width of valve including flange. 4. Location of control arm.. Diameter of opening to accommodate stem. 6. Type metal: 04, 6 Stainless or Galvanized Steel. For Flanges, please specify:. Pipe size. 2. Pressure rating.. Type metal: 04, 6 Stainless or Galvanized Steel. Cloth Shields For Valves, please specify:. Pipe size. 2. Type of valve and manufacturer.. Width of valve including flange. 4. Location of control arm.. Diameter of opening to accommodate stem. 6. Type cloth: Teflon, polyvinyl, polyethylene, polypropylene or Saran. For Flanges, please specify:. Pipe size. 2. Pressure rating.. Type cloth: Teflon, polyvinyl, polyethylene, polypropylene or Saran. For Expansion Joints, please specify:. Pipe size. 2. Manufacturer of expansion joint.. Number of convolutions. Note: Shields for expansion joints are manufactured of Teflon only. Saran and Teflon are registered trademarks of DuPont Co. 2

252 GASKETS AND SEALING PRODUCTS Spiral-Wound Gaskets Quality Construction Available in a full range of styles and materials, our spiral-wound gaskets are manufactured in accordance with API Standard 60/ASME B 6.20 for use in all industry flanges, including ASME/ANSI B 6., ASME B 6.47, API 60 and MSS SP-44. Our gaskets adhere strictly to these specifications as routine inspection procedures are applied throughout the manufacturing process. We maintain traceability of all materials used in our gasket construction to provide material certifications as required. Styles LG- LG--IR Spiral winding only Spiral winding with inner ring LG--HE Spiral winding with double jacketed rib LG- Spiral winding with outer guide LG--IR Spiral winding with outer guide and inner ring LG--HE Spiral winding with outer guide and double jacketed rib LG-4 Spiral winding for manholes and handholes LG- Spiral Windings with Outer Guides Style LG- gaskets are available in standard sizes. Additionally, LG-s can be custom made to meet specified dimensions. Both standard and custom LG-s are manufactured in the full range of winding metals, filler materials and outer guide alloys. LG- (API-60 / ASME B 6.20) Gasket Dimensions for ASME / ANSI B 6. Flanges Class 0, 00 Class 400, 600 Class 900 Class 00, lb. 00 lb. 400 lb. 600 lb.,00 lb. 2,00 lb. Flange Gasket Outer Outer Gasket Outer Outer Gasket Outer Gasket Outer Outer Size Guide Guide Guide Guide Guide Guide Guide (NPS) I.D. O.D. O.D. O.D. I.D. O.D. O.D. O.D. I.D. O.D. O.D. I.D. O.D. O.D. O.D. (In.) (In.) (In.) (In.) (In.) (In.) (In.) (In.) (In.) (In.) (In.) (In.) (In.) (In.) (In.) (In.) * *2 4** **NPS 0, Class 200 Gasket I.D. is 0 8. **NPS 2, Class 200 Gasket I.D. is 2 2. ASME B 6.20 requires inner guide rings on Teflon-filled gaskets. NOTE: Inner rings are required for Class 900 gaskets, NPS 24; Class 00 gaskets, NPS 2 through NPS 24; and Class 200 gaskets, NPS 4 through NPS 2. There are no Class 400 flanges in NPS 2 through NPS (use Class 600), Class 900 flanges in NPS 2 through NPS 2 2 (use Class 00), or Class 200 flanges NPS 4 and larger. 22

253 GASKETS AND SEALING PRODUCTS Spiral-Wound Gaskets continued LG-IR Inner Rings Styles LG--IR and LG--IR include a solid metal inner ring generally fabricated from the same metal as the winding. The inner ring is designed to minimize turbulence in process material flow and to prevent inward distortion of the spiralwound gasket element. The chart on the right gives the standard inside dimensions for Leader Gasket inner rings. Color Coding For your convenience, all gaskets are color coded on the edge of the outer guide as follows: Metal Windings 04SS Yellow 6LSS Green 2SS Turquoise 47SS Blue Alloy Black Carbon Steel Silver Hastelloy B Brown Hastelloy C Beige Inconel Gold Monel Orange Nickel Red Titanium Purple Fillers Leaderfite Pink Stripe Flexible Graphite Grey Stripe PTFE White Stripe Ceramic Light Green Stripe Standard (API-60) Inner Ring Inside Diameter for Spiral Wound Gaskets Flange Pressure Class Size (NPS) NOTE: Inner rings are required for Class 900 gaskets, NPS 24; Class 00 gaskets, NPS 2 through NPS 24; and Class 200 gaskets, NPS 4 through NPS 2. There are no Class 400 flanges NPS 2 through NPS (use Class 600), Class 900 flanges NPS 2 through NPS 2 2 (use Class 00), or Class 200 flanges NPS 4 and larger. Jacketed and Solid Metal Gaskets Leader Gasket manufactures a full line of metal gaskets including double jacketed, corrugated and plain solid in ring and ribbed configurations. Our metal gaskets are available in the full range of metals and fillers and are individually fabricated to meet customer specifications

254 GASKETS AND SEALING PRODUCTS O-Rings O-ring selections continue to climb! Green HNBR (HSN) Teflon Encapsulated (Viton ) Teflon Encapsulated (Silicone) Fluorocarbon Q-rings 7 Durometer Square Cut Rings Urethane 90 Durometer Urethane 70 Durometer Fluorocarbon Metric 7 Durometer Aflas 80 Durometer Teflon Spiral Back-ups Teflon Back-ups Teflon Neoprene 70 Durometer Silicone 70 Durometer EPR 70 Durometer Buna N Back-ups 90 Durometer Buna N Q-rings 70 Durometer Buna N Metric 7 Durometer Brown Fluorocarbon 7 Durometer Fluorocarbon 90 Durometer Fluorocarbon 7 Durometer Buna N 90 Durometer Buna N 70 Durometer Teflon and Viton are registered trademarks of the DuPont Co. and Aflas is a trademark of Asahi Glass Co. 24

255 SHEET RUBBER AND SPONGE RUBBER Rubber Sheeting Oil Resistant Neoprene Sheet Tan Pure Gum Sheet For use with petroleum oils and general gasket service. Rated: Tensile,000 lbs. Elongation 400% Wt./yd 2 at 8 thickness 9 lbs. Thickness Width (In.) (In.) Durometer No Neo Sheet Neo Sheet Neo Sheet Neo Sheet Neo Sheet Neo Sheet Neo Sheet Neo Sheet Neo Sheet Neo Sheet Neo Sheet Neo Sheet A natural rubber is compounded with a minimum of loading and accelerators. Flexible, resilient, with high tensile and elongation characteristics. Rated: Tensile 200 psi Elongation 600% Wt./yd 2 6 lbs. Thickness Width (In.) (In.) Durometer No Gum Sheet Gum Sheet Gum Sheet Gum Sheet Gum Sheet Gum Sheet Gum Sheet Gum Sheet Gum Sheet Gum Sheet Red SBR Sheet Viton Sheet A relatively inexpensive sheet, it is used as a gasketing material where resistance to extreme heat, acids, alkalis, salts, chemicals, etc. is not a problem. Rated: Tensile 400 lbs. Elongation 0% Wt./yd 2 at 8 thickness lbs. Thickness Width (In.) (In.) No Red Sheet Red Sheet Red Sheet Sold in quantities as small as one square foot. Viton has excellent resistance to heat, fuels, oils, solvents, and a wide range of corrosive chemicals. Rated: Tensile 800 psi Elongation 200% Wt./yd 2 at 8 thickness 0.7 lbs. Thickness Width (In.) (In.) Durometer No Viton Sheet Viton Sheet Cut gaskets are available from all material sheets. 2

256 SHEET RUBBER AND SPONGE RUBBER Rubber Sheeting continued White Food Grade Vinyl Sheet Butyl Sheet Compounded from FDA approved ingredients, white nitrile can be used for food and dairy applications. Material can be cleaned with soap and water. Rated: Tensile,000 lbs. Elongation 600% Wt./yd 2 at 8 thickness 9 lbs. Thickness Width (In.) (In.) Durometer No FDA Sheet FDA Sheet FDA Sheet FDA Sheet FDA Sheet FDA Sheet A synthetic rubber that has excellent resistance to ozone and weathering. Butyl is ideal for applications that require low permeability to liquids and gases. Excellent for energy absorption. Rated: Tensile 000 psi Elongation 00% Wt./yd 2 at 8 thickness 7. lbs. Thickness Width (In.) (In.) Durometer No Butyl Sheet Butyl Sheet Butyl Sheet Butyl Sheet Cloth Inserted Sheet Buna N Sheet Buna N has good resistance to hydrocarbon solvents, alkalines, petroleum oils, vegetable oils, aviation gasolines, and water. Rated: Tensile 000 psi Elongation 400% Wt./yd 2 at 8 thickness 8. lbs. Thickness Width (In.) (In.) Durometer No Buna Sheet Buna Sheet Buna Sheet Buna Sheet For use with hot or cold water, low pressure steam, air or gas where gaskets containing fabric are required to resist the cold flow of the rubber. Rated: Tensile 400 psi Wt./yd 2 at 8 thickness 0 lbs. Thickness Width (In.) (In.) Durometer No CI Sheet CI Sheet CI Sheet CI Sheet EPDM (Ethylene Propylene Diene-Monomer) Sheet Cut gaskets are available from all material sheets. Excellent resistance to heat aging, oxidation, ozone, alkalis and acids, this material also exhibits good electrical resistance. Rated: Tensile,00 lbs. Elongation 40% Wt./yd 2 at 8 thickness 7. lbs. Thickness Width (In.) (In.) Durometer No EPDM Sheet EPDM Sheet EPDM Sheet 26

257 SHEET RUBBER AND SPONGE RUBBER Rubber Sheeting continued Hypalon Sheet Silicone Sheet A synthetic rubber that has excellent ozone and acid resistance, Hypalon is good for use where elevated temperatures and chemicals are present. Rated: Tensile,800 lbs. Elongation 00% Wt./yd 2 at 8 thickness 8.2 lbs. Thickness Width (In.) (In.) Durometer No Hypalon Sheet Hypalon Sheet Hypalon Sheet Hypalon Sheet Red in color, this commercial grade is for use in areas where temperatures range from -6 F to 00 F. Thickness Width (In.) (In.) Durometer No x Silicone 24 Sheet 6 24 x Silicone 24 Sheet 6 6 x Silicone 6 Sheet x Silicone 24 Sheet 86 6 x Silicone 6 Sheet Closed Cell Sponge Rubber Sheet Diaphram Sheet Features all the properties of Neoprene combined with cotton reinforcement. Rated: Wt./yd 2 at 8 thickness 0 lbs. Thickness Width (In.) (In.) Durometer No Diaphram Sheet Diaphram Sheet Diaphram Sheet Diaphram Sheet Velvet finish nitrile construction. For use with high and low temperatures. Impervious to dust and air because cells are interconnected. Thickness Width (In.) (In.) Durometer No x 72 Medium, Soft 6 Closed Sponge Sheet x 72 Medium, Soft, Firm 6 8 Closed Sponge Sheet 6 42 x 72 Soft 6 Closed Sponge Sheet x 72 Soft-Medium 6 4 Closed Sponge Sheet x 72 Soft-Medium 6 8 Closed Sponge Sheet x 72 Soft, Medium, Firm 6 2 Closed Sponge Sheet x 72 Medium-Soft 6 4 Closed Sponge Sheet x 72 Soft-Medium, Firm 46 Closed Sponge Sheet Cut gaskets are available from all material sheets. 27

258 SHEET RUBBER AND SPONGE RUBBER Rubber Sheeting continued Open Cell Sponge Rubber Sheet Skirtboard (Chute Lining) Neoprene resists chemicals yet is bondable and flexible. High satin finish offers excellent resiliency. Thickness Width (In.) (In.) Durometer No. 4 6 Soft 4 Open Sponge Sheet 8 6 Soft 8 Open Sponge Sheet 2 6 Medium-Soft 2 Open Sponge Sheet 4 6 Medium-Soft 4 Open Sponge Sheet 4 6 Medium-Soft 4 Open Sponge Sheet Skirtboard is compounded to give excellent resistance to abrasion. As the name indicates, the material is used to line various types of conveying equipment that handles abrasive materials. Rated: Tensile 2,200 lbs. Elongation 200% Wt./yd 2 at 8 thickness 7 lbs. Max. Max. Thickness Width Roll Lgth. (In.) (In.) (Ft.) Durometer No Skirt Skirt Skirt Skirt Skirt Skirt Skirt Also available in specific widths: 4,, 6, 8, 0, 2 x 0 Long Military Specification Sheeting MIL R-68: Class NITRILE Grade 40 & 60 MIL R-68: Class 2 NEOPRENE Grade 40 & 60 MIL G-49: Type Class NEOPRENE MIL G-49: Type Class 2 SBR MIL R-276: NITRILE Cut Sheet Rubber Cut gaskets are available from all material sheets. 28

259 SHEET RUBBER AND SPONGE RUBBER Vibration and Shock Technology FABCEL Pads Features Square cells on each side of Fabcel Pads provide positive grip between machine foot and the floor. Uniform arrangement of square cells facilitate deflection of the Fabcel Pad under load. Fabcel Pads resist permanent set, oil, cleaning compounds, effects of sunlight, or air. They will not absorb oil and water. Cell pattern prevents the intrusion of foreign materials beneath the load-bearing area of the pad. Offset cell construction of Fabcel 2, 0 and 00 Pads (cells on opposite sides of pad offset from each other) provide positive grip under lighter loads. Specially-designed cell patterns for Fabcel 200 and 00 Pads provide optimum stability and vibration isolation for heavier loads. Benefits Permits low cost machinery mounting by eliminating the need for drilling, bolts, lag screws or adhesives. Greater lateral stability is achieved through the square cell design which provides continuous bearing areas on both sides of the pad in all directions. Reduces vibration, absorbs shock and controls noise. Prevents machinery from walking or creeping. Increases productivity and reduces machine maintenance time. Meets OSHA requirements for anchoring machines. Easily cut with scissors or sharp knife. Applications Typical Applications *Fabcel Pads Recommended Blowers to 00 Cold Headers Compressors** to 00 Coordinate Measuring** to 00 Dynamometers to 00 Fans** to 00 Generators to 00 HVAC Equipment to 00 Microscopes Printing Presses** to 00 Punching and Notching** to 00 Punch Presses** to 00 Riveting Machines to 00 Stereos Vacuum Pumps Vibratory Feeders to 00 Word Processing Equipment X-Ray Equipment **See How to Select Example section below. **May require isolated inertia block and anchoring. **Consult the Summers Rubber Company. How to Select Example.,600 lbs. machine weight = 900 lbs. per mounting point 4 mounting points lbs. = 4 psi 20 sq. in. (area of each mounting pad). Using the capacity section of the specification chart, the correct Fabcel Pad is Fabcel 0. Specifications Pad Size Pad Size A B Capacity (In.) (In.) Material No psi 8 x 8 x 6 6 x 6 x 6 Buna N FAB psi 8 x 8 x 6 6 x 6 x 6 Neoprene FAB psi 8 x 8 x 6 6 x 6 x 6 Neoprene FAB psi 8 x 8 x 22 6 x 6 x 22 Neoprene FAB psi 8 x 8 x 22 6 x 6 x 22 Neoprene FAB 00 N/mm 2 = 0.0kg/cm 2. Under impact machinery such as punch presses, the Fab Pads selected should be rated at 0% of capacity. Vibration Pads Machinery Mounts FABCEL is a registered trademark of the Fabreeka International, Inc.. 29

260 SHEET RUBBER AND SPONGE RUBBER Vibration and Shock Technology continued FABCEL Lev-L Mounts with Separate Bolt Standard Series Benefits Scientifically designed square foot suction cells firmly anchor machine to floor. Control noise, shock and vibration. Meets OSHA requirements for anchoring machinery. Permit fast, simplified, precise leveling of all types of machines and equipment. Self-aligning without sacrificing stability. Compensates for uneven floors. Eliminates danger of creeping or walking. Needs no cementing or bolting to floor. Save on new machine installations or relocation of existing equipment. Can be used over again when relocating machinery. Low initial cost. Can be unitized on special order. Applications *Fabcel Pads Typical Applications Recommended Bindery Equipment 0 to 40 Clickers 0 to 80 Collators 2 to 20 Conveyors 2 2 to 20 Coordinate Measuring** 2 to 40 EDM 2 to 40 Lathes 2 2 to 20 Milling Machines 0 to 20 Optical Comparators 2 2 to 40 Printing Presses** 0 to 20 Process Cameras 2 2 to 20 Punching and Notching 20 to 20 Robots to 20 Saws** to 20 Screw Machines to 80 Woodworking Machinery 2 2 to 20 **See How to Select Example section below. **May require isolated inertia block and anchoring. Consult Summers Rubber Co. How to Select Example. 4,000 lbs. machine weight =,000 lbs. per mounting point 4 mounting points 2. Using the maximum load range section of the specifications chart, the correct Fabcel Lev-L Mount for,000 lbs. is the Type 0.. For impact machinery, use next larger size. Machinery Mounts Specifications Base Load Range Bolt Min. Max. Overall Type Dia. Min./Max. Dia. Ht. A Adj. B Ht. C Mount (In.) (Lbs.) (In.) (In.) (In.) (In.) No Lev-L Mount Lev-L Mount , Lev-L Mount ,00-2, Lev-L Mount ,00-4, Lev-L Mount ,00-8, Lev-L Mount ,00-2, Lev-L Mount Maximum adjustment is reduced by machine foot thickness. Not available in metric thread. FABCEL is a registered trademark of the Fabreeka International, Inc.. 260

261 SHEET RUBBER AND SPONGE RUBBER Sheet Rubber Teflon Molded Sheet Style 00A Style 00A Virgin PTFE Teflon Mil-P-2224 molded and post annealed sheet is a highly stable material with uniform thickness and flatness. It is produced in a heavy-tonnage hydraulic press and sintered at high temperatures. PTFE Teflon is widely used in modern industry for it s outstanding characteristics, which are chemical inertness, heat-resistance up to 00 F (260 C), excellent dielectric properties, toughness, coefficient of friction, non-adhesive characteristics, moisture-resistance and weather-resistance. Sheet or rectangular stock can be furnished with one or more surfaces pre-treated for adhesive bonding and easily sawed, drilled, punched or die-cut, making it an ideal material for a wide variety of fabricated parts. Standard sheet sizes: 24 x x 48 6 x 6 48 x 48 Tolerance on length and width: Thickness tolerance: ±9% (special tolerance available). Other tolerances: Quoted on request. Etched PTFE sheets: One or both sides. Other thicknesses and sizes quoted on request. Thickness Wt./Ft. 2 (In.) (Lbs.) No TEF Sheet TEF Sheet TEF Sheet TEF Sheet TEF Sheet TEF Sheet TEF Sheet Industrial Matting: Ergonomic, Anti-Fatigue, Safety Products Sof-Spun and Sof-Spun Standard Durite 08 Sponge vinyl cushioned mat eases leg and back fatigue. Corrugated surface. 4 or 8 thickness. Colors: Black, Brown, Gray. Durite 08 H Herringbone Weave Durite 08 S Yellow Nosing Standard Sizes 8 Thick Size Wt. (In.) (Lbs.) No. 27 x 6. 7S x S x S660 4 Thick Rolls Size Wt. (Ft.) (Lbs.) No. 2 x R0024 x R006 4 x R x R Thick Rolls Size Wt. (Ft.) (Lbs.) No. 2 x R0024 x R006 4 x R x R0072 Special cut lengths available. Long wearing tough rubberized tire link mats provide comfort and safety. Rubberized links woven on galvanized wires. 8 thickness. Open mesh construction provides excellent drainage. Available in herringbone or straight weave. Size Wt. (In.) (Lbs.) No. 4 x H422 7 x H72 20 x H x H247 0 x H048 0 x H062 6 x H672 *Substitute S for straight weave. *Special sizes, and black or yellow nosing also available. Teflon is a registered trademark of the DuPont Co. 26

262 SHEET RUBBER AND SPONGE RUBBER Industrial Matting: Ergonomic, Anti-Fatigue, Safety Products continued Workmaster II Grandstand Tough industrial open weave mat with colored safety border provides the ultimate in comfort and safety. 7 8 thick. Grease resistant mat. Border colors: Yellow (YE), Orange (standard)*, Red (RD), Green (GN), Blue (BL). Size Wt. (In.) (Lbs.) No. 28 x S x S x S x S424 *Orange border is standard specify color if other than orange is desired. Marbelized rubber surface with 2 foam backing provides superior comfort. Thickness 8 overall 2 foam, 8 surface. Excellent comfort in industrial and institutional work areas. Not recommended for high heel traffic. Colors: Black/White (BW), Charcoal (CH), Terra Cotta (TC), Blue (BL), Brown (BN), Light Gray (LG). Size Wt. (In.) (Lbs.) No. 8 x S80 8 x S x S246 6 x S660 Special lengths available. Specify color. Workstation Plus Dura-Rug 400 Lightweight industrial mat with open mesh construction. 2 thickness. All sizes include built in beveled edges. Ideal for oil and grease applications. Colors: Black, Gray, Red. Size Wt. (In.) (Lbs.) No. x 2 49S00 x S00 x S020 Specify color. Buffed rubberized tire link mat provides excellent scraping and drainage. Perfect for entrance areas indoor or outdoor. Tough rubberized fabric surface provides the maximum scraper mat. Open mesh construction for drainage. Approximately 4 thick. Available in straight weave only. Size Wt. (In.) (Lbs.) No. 4 x S422 7 x S72 20 x S x S247 0 x S048 0 x S062 6 x S672 Special sizes available with or without Black or Yellow nosings. 262

263 SHEET RUBBER AND SPONGE RUBBER Industrial Matting: Ergonomic, Anti-Fatigue, Safety Products continued Diamond Dek Sponge Super-Dek Sponge Heavy duty matting with diamond tread pattern provides sure footing in a variety of applications. 8 Koroseal vinyl surface bonded to 2 thick foam backing 8 thickness overall. 2 foam backing is resistant to many common oils, alkilydes, acids. Colors: Solid Black, Solid Gray, Black with OSHA Yellow borders, Black with Orange border, Blue border, Red border, or Green border. Standard Sizes* Size Wt. (In.) (Lbs.) No. 24 x S246 6 x S660 *Specify Black, Gray or Black with OSHA Yellow border. Full Rolls 7 length* Size Wt. (In.) (Lbs.) No. 2 x R0024 x R006 4 x R0048 *Special lengths up to 7 available. Exclusive 8 00% recycled non-skid vinyl surface is excellent for most industrial applications where comfort and safety are a must. Recycled PVC surface with textured top is bonded to a 2 foam (overall thickness 8 ). Resists variety of chemicals. Much more economical than most bonded mats. Colors: Solid Black, Solid Gray, Black with Yellow borders. Standard Sizes* Size Wt. (In.) (Lbs.) No. 24 x S246 6 x S660 *Specify color. Full Rolls Size Wt. (In.) (Lbs.) No. 2 x R0024 x R006 4 x R0048 Special lengths available. Workstation and Workstation Solid 7 8 thick industrial mat is perfect for most industrial applications. Available in solid or open mesh design. Beveled edges available. Mats have built in interlocking system that can be connected to extend length and width. Colors: Black or Grease Proof Red. Workstation Workstation Solid Size Wt. (In.) (Lbs.) No. x 20 40S66 x 20 40W66 26

264 SHEET RUBBER AND SPONGE RUBBER Industrial Matting: Ergonomic, Anti-Fatigue, Safety Products continued Rubber Matting Easy Sweep Round Tread-Grid Typical locations: Supermarkets, restaurants, hospitals, department stores, locker rooms, gymnasiums, factories, military installations, office towers, hotels/motels, sports complexes, laboratories, banks, medical offices, schools, step stools, golf carts, farm equipment, buses and hundreds of other applications. Widths: 24, 6, 48. Colors: Black, Brown, Beige, Terra Cotta, Green, Grey, White (Black in stock). : 8 x 6 EZY 8 x 48 EZY Super-Dek Runner Super Grip Vinyl Duckboard mat with open mesh construction provides comfort and safety. Highly chemical resistant. Retains maximum flexibility in temperatures from -40 F to 22 F. Colors: Black (BK), Red (RD), Blue (BL). Size Wt. (In.) (Lbs.) No. 2 x 40 9 R0024 x R006 4 x R0048 Specify color. Special lengths available. Cushion Tile Economical non-skid runner is perfect in covering areas where slips and falls may occur. 8 thick, 00% recycled PVC. Textured surface provides the best non-skid mat available. Highly chemical resistant. Size Wt. (In.) (Lbs.) No. 2 x R0024 x R006 4 x R0048 Our modular flexible vinyl compound provides safety and comfort indoors or outdoors. 4 thick with open mesh design. Beveled nosing available in black or safety yellow. Ideal for applications where large areas need covered. Size Wt. (In.) (Lbs.) No. 2 x 2. 80S22 2 x 2. 80M022 Male beveled edge 2 x 2. 80F022 Female beveled edge 2 x.. 80M02 Male beveled corner 2 x.. 80F02 Female beveled corner 264

265 SHEET RUBBER AND SPONGE RUBBER Industrial Matting: Ergonomic, Anti-Fatigue, Safety Products continued Anti-Slip Tape Anti-Static/Anti-Fatigue Slip resistant, high traction, pressure sensitive backed grit surface strips provide excellent non-skid footing in areas where grease, water and other liquids accumulate on floors. Meets OSHA standards for a variety of safety requirements. Color: Black. Size Wt. (In.) (Lbs.) No. x 60 Roll 82R000 2 x 60 Roll 82R x 60 Roll 82R x 60 Roll 82R x 2 0 pcs. 82S00 6 x 24 0 pcs. 82S0624 Matting dissipates static buildup to effectively eliminate potential data loss or damage to sensitive electronic equipment. 8 sponge mat also provides excellent fatigue relief. Textured slip resistant surface. One ground cord included with each standard size and roll. Recommend -0 ground cord per 0 of mat. Color: Brown. Standard Sizes Size Wt. (In.) (Lbs.) No. 24 x S x S2460 Full Rolls Size Wt. (In.) (Lbs.) No. 2 x R0024 x R006 4 x R Ground Cord 90G0000 Special lengths available. 26

266 SHEET RUBBER AND SPONGE RUBBER Urethane Sheet, Rod, Tubing and More Urethane Sheet, Pads and Belt Wipers Urethane Rod and Tubing In addition to our other fine urethane products, we offer a variety of standard urethane shapes such as rod, tubing, and sheet. Formulated with the highest quality urethanes, these products are available in standard and custom sizes, compounds and colors. Precision cast urethane sheet: Available in a 0 x 96 sheet, thicknesses from 2 8, thickness tolerance ±.00 standard or ±.00 special order. Open cast urethane sheet and pads: Standard sizes include 24 x 24, 24 x 48, 48 x 48. Custom sizes up 60 x 44 and 48 x 600 (0 ). Thicknesses from 8. Urethane rod: Standard sizes include 2 6 diameter x 6 long. Custom sizes are available. Urethane tubing: Available in various I.D./O.D. combinations and lengths. Custom slit rings also available. Urethane roll recovering: Our expertise in this area allows consistent, high quality work at reasonable prices. Our equipment can handle rolls up to 2 diameter x 68 long, with hardness from 0A-80D. We have tough, durable compounds to handle pull, print, coater, sander, drive and idler rolls, with diameter tolerances as close as ±.00. Custom molded products: The Summers Rubber Company will gladly quote work from your prints or sample parts. All of these products are available in compounds from 0A- 7D. Call your Summers Rubber Company representative for more information. Urethane Ware Products for the Aggregate Industry Urethane Rollers Urethane Wheels 266

267 General Belt Construction How to Get Top Performance from Your V-Belt Drives How to Install V-Belt Drives V-Belt Drive Standards Technical Data Heavy Duty V-Belts Super HC Molded Notch V-Belts Super HC V-Belts Hi-Power II V-Belts Tri-Power Molded Notch V-Belts PowerBand Belts Super Vulco Ropes Hi-Power II Dubl-V-Belts Power Cable Belts Heavy Duty Sheaves Super HC Sheaves Vulcomount (A, B, C and D) Sheaves Belt Drive Tensioners and QD Bushing Idlers Stationary Control Variable Pitch Sheaves Multi-Speed Drives Multi-Speed Belts Light Duty (FHP) Drives Polyflex Belts Truflex V-Belts (including Special Light Duty Belts) PoweRated Belts Light-Duty Sheaves V-Belting Easy-Splice V-Belting Nu-T-Link V-Belting Vulco-Link V-Belting Vulco-Flex V-Belting Specialized Belts Bowling Machine Belts Flat Belts (Speed-Flex and Powercord ) Round Endless Belts Miehle Press Flat Belts POWER TRANSMISSION PRODUCTS Power Transmission Products Built by Gates, Supplied by Summers Rubber Company Matching System All Gates Super HC and Super HC Molded Notch V-Belts labelled with the V-80 symbol will match all other Gates Super HC or Super HC Molded Notch V-Belts of the same size also marked with the V-80 symbol. Super HC, Tri-Power, PowerBand, Super Vulco, Vulcomount, Polyflex, Truflex,, PoweRated, Vulco-Flex, Speed-Flex V-80, and Powercord are registered trademarks and Hi-Power II is a trademark of Gates Rubber Company. 267

268 POWER TRANSMISSION PRODUCTS Nominal Dimension and Stock Lengths Super HC and Super HC Molded Notch V-Belts.0.8 V V.62 VX.4 8V VX VX V 8V Outside Circumference (In.) Super HC Molded Notch V-Belt Outside Circumference (In.) Super HC Molded Notch V-Belt Super Outside HC Circumference V-Belt (In.) Super Outside HC Circumference V-Belt (In.) 2. VX VX VX VX00. VX. VX. VX 7. VX7 40. VX VX42 4. VX VX47 0. VX00. VX0 6. VX VX VX VX VX70 7. VX VX VX VX VX VX VX VX20 8. VX80 2. VX20 2. VX VX400 0 VX00 VX0 6 VX60 60 VX600 6 VX60 67 VX670 7 VX70 7 VX70 80 VX800 8 VX80 90 VX900 9 VX90 00 VX VX060 2 VX20 8 VX80 2 VX20 2 VX20 40 VX400 0 VX00 60 VX VX VX V V V V V V V V V000 V0 V0 V0 00 8V V V20 8 8V80 2 8V20 2 8V V V V V V V V V V V V V V V000 8V0 8V0 8V0 7 8V V V V V V V *8V6000* This length is available only as PowerBand. Single belts are not available in this size. Super HC and PowerBand are registered trademarks of Gates Rubber Company. 268

269 POWER TRANSMISSION PRODUCTS Heavy-Duty V-Belts Gates Hi-Power II V-Belts Size Listing.0 A Section Continued.66 B Section Continued. A Section Outside Circum- Pitch Hi-Power II ference Length V-Belt (In.) (In.) *A24* *A26* *A27* *A28* *A29*.9.8. *A29.8* 2.. *A0* *A* *A2* *A* *A4* *A* *A6* *A7* *A8* *A9* *A40* *A4* *A42* *A4* *A44* *A4* *A46* *A47* *A48* *A49* *A0* *A* *A2* *A* *A4* *A* *A6* *A7* *A8* *A9* *A60* *A6* *A62* *A6* *A64* *A6* *A66* *A67* *A68* *A69* *A70* *A7* *A72* *A7* *A74* *A7* *A76* *A77* *A78* *A79* *A80*.9 Outside Circum- Pitch Hi-Power II ference Length V-Belt (In.) (In.) *A8* *A82* *A8* *A84* *A8* *A88* *A90* *A92* *A9* *A96* *A00* *A0* *A0* 2. *A0* 4. *A2* 7 6. *A* *A20* *A28* 4. *A* 8 7. *A6* *A44* *A8* *A7* *A80* PowerBand Belts are not stocked. *Stocked for availability and are not recommended for new drives. Note: To order the correct length when replacing wornout V-Belts, if the present belt number is no longer legible, measure the belt length with a flexible tape around the outside circumference, preferably before the belts have been removed from the drive. Then order those Hi-Power II V-Belts which have the next shorter standard length, as determined in the table of Hi-Power II V-Belt sizes..4 B Section Outside Circum- Pitch Hi-Power II ference Length V-Belt (In.) (In.) 29.8 *B28*.8 *B0*.8 *B2* 7.8 *B4* *B* *B6* *B8* *B40 * *B4 * *B42* *B4* *B44 * *B4* *B46* *B47* 49.8 *B48* *B49 *.8 *B0* *B*.8 *B2* *B* 7.8 *B4* *B* *B6* *B7* *B8* *B9* *B60* *B6* *B62* *B6* *B64* *B6* *B66* *B67* *B68* *B69* *B70* *B7* *B72* *B7* *B74* *B7* *B76* *B77* *B78* *B79* *B80 * *B8* *B82* *B8* *B84* *B8 * *B86* *B87* *B88* *B89* Outside Circum- Pitch Hi-Power II ference Length V-Belt (In.) (In.) *B90* *B9* *B92* *B9* *B94* *B9 * *B96* *B97* *B98* *B99* *B00 * *B0* *B0* 09.8 *B08*.8 *B2* *B6* *B8* *B20 * *B24* 29.8 *B28* *B* *B6* *B40* *B44* 49.8 *B48* *B8 * *B62* *B7* *B80* *B90* *B9* *B20 * *B20* *B22* *B240* *B2* *B270* *B28 * *B00* 6. *B* PowerBand Belts are not stocked in sizes designated. *Stocked for availability and are not recommended for new drives. PowerBand is a registered trademark and Hi-Power II is a trademark of Gates Rubber Company. 269

270 POWER TRANSMISSION PRODUCTS Heavy-Duty V-Belts continued Gates Hi-Power II V-Belts Size Listing.88. C Section Outside Circum- Pitch Hi-Power II ference Length V-Belt (In.) (In.).9 * C * * C * * C60* * C68* * C7 * * C72* * C7* * C78* * C8* * C8* * C90* * C96* * C97* * C99* * C00* * C0* * C06 * * C08*.9 * C09*.9 * C* * C2* * C * * C20* * C24* * C28* * C6* * C44* * C6* * C8* * C62* * C7* * C80* * C90* PowerBand Belts are not stocked in sizes designated. *Stocked for availability and are not recommended for new drives. C Section Continued Outside Circum- Pitch Hi-Power II ference Length V-Belt (In.) (In.) * C9* * C20 * * C22* * C240* * C2* * C270* * C28 * * C00* 7.9 * C* * C0* * C4* * C60* * C908* * C420* Note: To order the correct length when replacing wornout V-Belts, if the present belt number is no longer legible, measure the belt length with a flexible tape around the outside circumference, preferably before the belts have been removed from the drive. Then order those Hi-Power II V-Belts which have the next shorter standard length, as determined in the table of Hi-Power II V-Belt sizes..2 D Section.7 Outside Circum- Pitch Hi-Power II ference Length V-Belt (In.) (In.) R* D0* 7. R* D2* 2 2. R* D20*. R* D28 * R* D44* 6 6. R* D8* R* D62 * R* D7* 8 8. R* D80* R* D9* 2 2. R* D20* R* D22* R* D240* R* D2* R* D270* R* D28* R* D00* 7.8 R* D* R* D0 * * DR4 * * DR60 * * DR90 * * DR420 * * DR40 * * DR480 * * DR40 * * DR600 * * DR660 * PowerBand Belts are not stocked in sizes designated. DR Belts are Rib-Top V-Belts, 62 O.C. and longer. *Stocked for availability and are not recommended for new drives..0 E Section.9 Outside Circum- Pitch Hi-Power II ference Length V-Belt (In.) (In.) * E80* * E9* * E20* * E240 * * E270* * E00*.0 * E0 * * E60* * E90* * E420* * E480* * E40* * E600* * E660* PowerBand Belts are not stocked. PowerBand is a registered trademark and Hi-Power II is a trademark of Gates Rubber Company. 270

271 POWER TRANSMISSION PRODUCTS Series 842 Gates PoweRated V-Belts are built with an aramid fiber that is pound-for-pound stronger than steel. Aramid fiber is so tough it s used in tires and bulletproof vests. PoweRated V-Belts deliver more horsepower than conventional light-duty belts and are ideal for applications from riding mowers to snow blowers, washing machines to shop equipment up to 7 horsepower. Use PoweRated belts to replace Truflex belts on other problem drives. Due to the bareback band ply, PoweRated belts are the best choice for smooth clutching drives and backside idlers. These belts resist temperature extremes, high humidity, oil and cracking. Aramid fiber tensile cords provide superior shock load capability. PoweRated belts require minimal retensioning and takeup. Belt O.C. (In.) Section No PowerRated Data Industry Gates PoweRated Designation Truflex Section Section L 67 ( 8 T.W.) 4L 2 68 ( 2 T.W.) L 69 ( 2 2 T.W.) /8 7/2 Light-Duty PoweRated V-Belts Section Continued Belt O.C. (In.) No Belt O.C. (In.) /2 /6 2 Section No Section Continued Belt O.C. (In.) No /2 /8 Section Belt O.C. (In.) No Section Continued Belt O.C. (In.) No PoweRated and Truflex are registered trademarks of Gates Rubber Company. 27

272 POWER TRANSMISSION PRODUCTS Industrial Belting Nu-T-Link Belting Product No. Series 7760 Supreme V-Link Belting Product No. Series 7760 Nu-T-Link Belting is high performance, link belting and is an excellent problem solver. The belting is made from a special polymer which has excellent resistance to many chemicals. Experience has shown that the smooth-running characteristics of Nu-T-Link will be a benefit in high precision applications. A Gates exclusive in the United States. Advantages Improved service life under adverse chemical or atmospheric conditions. Working temperature range: -40 F to 22 F (-40 C to 00 C). High resistance in heat, steam, oil and chemical environments. Incorporates an easy-to-use linkage system (U.S. Pat ). Available in all standard classical RMA sections. Nu-T-Link 0 per reel Top Cross Width Section (In.) OO 68 NTL/OO* O 888 NTL/O A 288 NTL/A B 2 2 NTL/B C NTL/C D 488 NTL/D E 288 NTL/E* *Made-to-order, minimum quantity may apply. Check with customer service for availability. Note: Do not use with backside idlers. Nu-T-Link does not meet RMA requirements for V-belt static conductivity. Supreme V-Link Belting is a high performance, multi-purpose product made from a composite polyester/polyurethane material. It offers excellent resistance to oil and heat with minimum stretch. It is available in Sections OO through B with color coded studs for easy identification and is supplied in 00 lengths only. Supreme V-Link 00 per reel Top Cross Width Section (In.) OO 68 SVL/OO* O 888 SVL/O A 288 SVL/A B 2 2 SVL/B *Made-to-order, minimum quantity may apply. Check with customer service for availability. Supreme V-Link Belting Assembly Tool A Nu-T-Link assembly tool will be supplied free of charge with belting. Additional assembly tools are available from the Summers Rubber Co. Nu-T-Link is a registered trademark of Fenner Manheim. 272

273 POWER TRANSMISSION PRODUCTS Drives and Belting Mini-Pitch Belting Twin Power Belts Long-Length Belting The tooth profile of the Mini-Pitch belt is a miniature version of the timing belt design 40 angle tooth. Mini-Pitch belts are made with a.080 pitch. This is a standard design pitch recognized by the Rubber Manufacturers Association and lso Mini-Pitch belts can have a speed ratio of 8: with a center distance of. ; or, a center distance of 0.84 at a : speed ratio. They can operate on pulleys as small as 0.2 pitch diameter. There are standard widths ( 8, 6 and 4 ) in pitch lengths from.6 to 2.0. Mini-Pitch belts are available in both neoprene and urethane constructions. Peak Design Torque ratings range from 0.29 to 2.0 Ibs. Catalog 78 Design Manual 78 Twin Power belts are available in HTD or Timing Belt pitches with nylon-jacket-covered teeth on both sides of the belt. This lets them transmit up to 00% of the maximum rated load for the given design pitch from either side of the belt; or, in combination when the sum of the loads does not exceed the belt rating. Conventional Timing Belt designs are available as stock or made-to-order (MTO) in, 8 and 2 pitches in belt pitch lengths to 46. Power transmission ratings range from 0.00 hp to 67 hp. Speed ratings range up to 0,000 rpm and ratios to 8.7:. Belts with the HTD tooth are available as MTO belts in mm, mm, 8mm and 4mm pitches in belt pitch lengths of 86. Power transmission ratings range from below 0.0 hp to 90 hp. Speed ratings range up to 4,000 rpm and speed ratios to 8.7:. HTD and MTO Belts: Catalog 78 Stock Timing Belts: Design Manual 78 Long-length belting is used for power transmission, synchronization and functional applications such as conveying, positioning, etc. It is available with conventional Timing Belt or HTD belt tooth configurations in standard rolls approximately 00 long. Continuous rolls of more than 00 are available on special order. It can be field spliced although tensile strength is reduced 2% of rated capacity. Long-length belting with the timing belt tooth configuration is available as stock and made-to-order (MTO) in, 8 and 2 pitches. Made-to-order HTD tooth configurations are available in 8mm pitches. HTD and MTO Belts: Catalog 78 Contact Summers Rubber Company with your specific application requirements. Twin Power is a registered trademark of Gates Rubber Company. 27

274 POWER TRANSMISSION PRODUCTS Stock Synchronous Timing Belt Drives HTD Belt Drives Poly Chain GT Belt The original timing belt uses the patented tooth design developed by Gates. Millions of these belts are in use today and design engineers still find applications for their unique characteristics. There are six standard pitches in the PowerGrip Timing Belt Manual. Standard design pitches range from to 4. Power transmission ratings begin at 0.00 hp and range up to 67 hp. Speed ratings range up to 0,000 rpm with ratios to 8.7:, depending upon belt design pitch. Special pitches are available on a made-to-order basis from more than 700 molds currently in stock. Design Manual 78 Note: Gates recommends that Gates PowerGrip timing belts are to be run only on Gates PowerGrip timing pulleys. The patented curvilinear tooth design of the HTD drive achieves superior stress distribution to achieve maximum load capacity and power transmission efficiency. Depending on drive conditions, HTD belt drives carry from 20% to 00% more power per inch of width than conventional timing belt drives. Standard HTD belt drives are available in stock pitches ranging in size from tiny mm pitch belts to giant 20mm pitch belts. Belt pitch lengths range up to 270. Power transmission ratings begin at under lb. of torque and go up to over 200 hp. Speed ratings range up to 20,000 rpm with, using stock belts, speed ratios up to 8.7:, depending on belt pitch. Speed ratios to 20: are practical for made-to-order (MTO) belts. Ask for the following Design Manuals: mm & mm Belts: Design Manual 78 8mm & 4mm Belts: Design Manual mm Belts: Design Manual 790 The specially-engineered Poly Chain GT tooth design (U.S. Patent No. 4,60,89) allows the belt to move smoothly into and out of the sprocket, resulting in increased drive performance. Moreover, Poly Chain GT belts withstand sudden power surges and shock loading and reduce the heavy pressures exerted on the land area of the sprocket system. Controlled laboratory testing reveals that these Gates belts can carry up to four times the load of rubber HTD belts for the same service life, depending on specific drive conditions. Standard Poly Chain GT belt drives will be available in two stock pitches 8mm and 4mm and belt pitch lengths range up to 76. Speed ratios of more than 0: can be achieved with stock components. Design Manual 79 Note: Gates recommends that Gates PowerGrip HTD belts are to be run only on Gates PowerGrip HTD sprockets. 274

275 SWIVEL, ROTARY AND BALL JOINTS AND VALVES Swivel Joints Swivel Joints Meet Numerous Application Requirements Summers Rubber Co. stocks swivel joints for a broad range of uses in the petroleum, machine tool, chemical, refining, mining, distilling, brewing, and paint industries, as well as farm irrigation and fertilizing, and hundreds of OEM applications. Design, maintenance and plant engineers use swivels in flexible piping systems, loading arms, hose reels, sewer rodding and wastewater treatment equipment, and various types of process machinery. They are also widely used for machine tool coolant transfer, drum filling applications, and a variety of in-plant fluid and dry bulk transfer operations. Availability by Material, Size and Pressure Rating Size Pressure Material Rating* Steel, Cast, High-Pressure, 200 Series X X X X,000 psi Steel, Fabricated, 400 Series X X X X X X,000 psi 6 Stainless Steel, 700 & 900 Series X X X X X X X X X,000 psi Aluminum, 600 Series X X X X X X,2 psi Ductile Iron, 800 Series X X X X X,600 psi Bronze, 00 Series X X X X,00 psi *Maximum pressure rating of swivel joints is as shown, or is determined by the flange/end connection rating, whichever is lower. *Buna N seals are standard in all of the above swivel joints, but each is available with seals made of Viton, Teflon, EPT, or Neoprene, depending on the *pressures and temperatures of your operation. Styles Available Swivel joints are available in one, two or three planes of rotation for virtually unlimited flexibility. Standard combinations of five different metals and seal materials cover pressures, temperatures, corrosion resistance, and load bearing capacities well within the limits of most application requirements. Style 0 planes of rotation Style 20 plane of rotation Style 0 plane of rotation Style 40 plane of rotation Style 0 2 planes of rotation Style 60 2 planes of rotation Style 70 2 planes of rotation Style 80 planes of rotation Note: Flanged or butt weld ends are available in many styles and sizes. Only the most common styles of swivel joints appear on the following pages. If you don t see exactly what you need, consult the Summers Rubber Company for assistance. Viton and Teflon are registered trademarks of the DuPont Co. 27

276 SWIVEL, ROTARY AND BALL JOINTS AND VALVES Swivel Joints continued Cast Fabricated Rotary manifold boards use swivel joints and dry disconnect fittings to clean up messy hose exchange areas in blending and similar operations. Swivel joints are available in two types of body construction, cast and fabricated, which differ in appearance. For the sake of simplicity, the drawings featured on the following pages are mostly fabricated types. Note: Swivel joints are subject to periodic design revisions. The specifications, dimensions, and illustrations in this catalog are, therefore, also subject to change. Certified dimensional drawings are available on request. Style 20 Thread x Thread Style 20W Butt Weld x Butt Weld Style 0F Flange x Flange Size (In.) Material No., 4, 2, 2 Steel, Cast, High-Pressure 220 2,, 4 Steel, Fabricated 420 4,, 2 Stainless Steel, Cast 720 2,, 4 Stainless Steel, Fabricated 920, 2, 2,, 4 Aluminum 620, 2, 2,, 4 Ductile Iron 820, 2, 2, Bronze 20 Style 20F Flange x Flange Size (In.) Material No. 2,, 4, 6, 8, 0 Steel, Fabricated 420W 2,, 4, 6, 8, 0 Stainless Steel, Fabricated 920W Style 0 Thread x Thread Size (In.) Material No. 2,, 4, 6, 8, 0 Steel, Fabricated 40F 2,, 4, 6, 8, 0 Stainless Steel, Fabricated 90F, 4, 6 Aluminum 60F, 4 Ductile Iron 80F Style 0FJ Flanged for Submerged Use Size (In.) Material No. 2,, 4, 6, 8, 0 Steel, Fabricated 420F 2,, 4, 6, 8, 0 Stainless Steel, Fabricated 920F, 4, 6 Aluminum 620F Size (In.) Material No., 4, 2, 2 Steel, Cast, High-Pressure 20 2,, 4 Steel, Fabricated 40 4,, 2 Stainless Steel, Cast 70 2,, 4 Stainless Steel, Fabricated 90, 2, 2,, 4 Aluminum 60, 2, 2,, 4 Ductile Iron 80, 2, 2, Bronze 0 Size (In.) Material No. 2,, 4, 6, 8, 0 Steel, Fabricated 40FJ 2,, 4, 6, 8, 0 Stainless Steel, Fabricated 90FJ, 4, 6 Aluminum 60FJ 276

277 SWIVEL, ROTARY AND BALL JOINTS AND VALVES Swivel Joints continued Style 0FO Flange x Thread Style 4F Flange x Flange Style FT TTMA Truck Flanges Size (In.) Material No. 2,, 4 Steel, Fabricated 40FO 2,, 4 Stainless Steel, Fabricated 90FO, 4 Aluminum 60FO, 4 Ductile Iron 80FO Style 0W Butt Weld x Butt Weld Size (In.) Material No. 2,, 4, 6 Steel, Fabricated 44F 2,, 4, 6 Stainless Steel, Fabricated 94F Style Thread x Thread Size (In.) Material No. 4 Aluminum 6FT 4 Aluminum 6FTH* *Comes complete with straight pipe handle. Style 40 Thread x Thread Size (In.) Material No. 2,, 4, 6, 8, 0 Steel, Fabricated 40W 2,, 4, 6, 8, 0 Stainless Steel, Fabricated 90W Style 4 Thread x Thread Size (In.) Material No. 2,, 4 Steel, Fabricated 4 2,, 4 Stainless Steel, Fabricated 9, 4 Aluminum 6 Style F Flange x Flange Size (In.) Material No., 2, 2 Steel, Cast, High-Pressure 240 2,, 4 Steel, Fabricated 440, 2 Stainless Steel, Cast 740 2,, 4 Stainless Steel, Fabricated 940 2, 2,, 4 Aluminum 640 2,, 4 Ductile Iron 840, 2, Bronze 40 Style 40F Flange x Flange Size (In.) Material No. 2,, 4 Steel, Fabricated 44 2,, 4 Stainless Steel, Fabricated 94 Size (In.) Material No. 2,, 4, 6 Steel, Fabricated 4F 2,, 4, 6 Stainless Steel, Fabricated 9F Size (In.) Material No. 2,, 4, 6, 8, 0 Steel, Fabricated 440F 2,, 4, 6, 8, 0 Stainless Steel, Fabricated 940F, 4, 6 Aluminum 640F, 4 Ductile Iron 840F 277

278 SWIVEL, ROTARY AND BALL JOINTS AND VALVES Swivel Joints continued Style 40FJ Flanged for Submerged Use Style 40FTO TTMA Truck Flange x Thread Style 44F Flange x Flange Size (In.) Material No. 2,, 4, 6, 8, 0 Steel, Fabricated 440FJ 2,, 4, 6, 8, 0 Stainless Steel, Fabricated 940FJ 2,, 4, 6 Aluminum 640FJ Style 40FO Flange x Thread Size (In.) Material No., 4 Aluminum 640FTO Style 40W Butt Weld x Butt Weld Size (In.) Material No. 2,, 4 Steel, Fabricated 444F 2,, 4 Stainless Steel, Fabricated 944F, 4, 6 Aluminum 644F Style 44FO Flange x Thread Size (In.) Material No. 2,, 4 Steel, Fabricated 440FO 2,, 4 Stainless Steel, Fabricated 940FO, 4 Aluminum 640FO, 4 Ductile Iron 840FO Size (In.) Material No. 2,, 4, 6, 8, 0 Steel, Fabricated 440W 2,, 4, 6, 8, 0 Stainless Steel, Fabricated 940W Style 44 (Loading Arm Drop Tube Swivel with Grasp Handle) Thread x Thread Size (In.) Material No. 2,, 4 Steel, Fabricated 444FO 2,, 4 Stainless Steel, Fabricated 944FO, 4 Aluminum 644FO Style 44FT TTMA Truck Flanges Style 40FT TTMA Truck Flanges Size (In.) Material No. 2,, 4 Steel, Fabricated 444 2,, 4 Stainless Steel, Fabricated 944 2,, 4 Aluminum 644 Size (In.) Material No., 4 Aluminum 644FT Size (In.) Material No., 4 Aluminum 640FT 278

279 SWIVEL, ROTARY AND BALL JOINTS AND VALVES Swivel Joints continued Style 44FTO TTMA Truck Flange x Thread Style 0 Thread x Thread Style 0FT TTMA Truck Flanges Size (In.) Material No., 4 Aluminum 644FTO Style 4 Thread x Thread Size (In.) Material No., 2, 2 Steel, Cast, High-Pressure 20 2,, 4 Steel, Fabricated 40, 2 Stainless Steel, Cast 70 2,, 4 Stainless Steel, Fabricated 90 2, 2,, 4 Aluminum 60 2,, 4 Ductile Iron 80 Style 0F Flange x Flange Size (In.) Material No., 4 Aluminum 60FT Style 0W Butt Weld x Butt Weld Size (In.) Material No. 2,, 4 Steel, Fabricated 44 2,, 4, Stainless Steel, Fabricated 94, 4 Aluminum 64 Style 4F Flange x Flange Size (In.) Material No. 2,, 4, 6, 8, 0 Steel, Fabricated 40F 2,, 4, 6, 8, 0 Stainless Steel, Fabricated 90F, 4 Aluminum 60F, 4 Ductile Iron 80F Size (In.) Material No. 2,, 4, 6, 8, 0 Steel, Fabricated 40W 2,, 4, 6, 8, 0 Stainless Steel, Fabricated 90W Style Thread x Thread Size (In.) Material No. 2,, 4, 6 Steel, Fabricated 44F 2,, 4, 6, Stainless Steel, Fabricated 94F Style 0FO Flange x Thread Size (In.) Material No. 2,, 4 Steel, Fabricated 40FO 2,, 4 Stainless Steel, Fabricated 90FO, 4 Aluminum 60FO, 4 Ductile Iron 80FO Size (In.) Material No. 2,, 4 Steel, Fabricated 4 2,, 4 Stainless Steel, Fabricated 9, 4 Aluminum 6 2, Ductile Iron 8 279

280 SWIVEL, ROTARY AND BALL JOINTS AND VALVES Swivel Joints continued Style F Flange x Flange Style FT TTMA Truck Flanges Style 60F Flange x Flange Size (In.) Material No. 2,, 4, 6 Steel, Fabricated 4F 2,, 4, 6 Stainless Steel, Fabricated 9F Style FFT Flange x TTMA Truck Flange Size (In.) Material No. 4 Aluminum 6FT Style TFT Thread x TTMA Truck Flange Size (In.) Material No. 2,, 4, 6, 8, 0 Steel, Fabricated 460F 2,, 4, 6, 8, 0 Stainless Steel, Fabricated 960F, 4 Aluminum 660F, 4 Ductile Iron 860F Style 60FO Flange x Thread Size (In.) Material No., 4 Steel, Fabricated 4FFT Ductile Iron 8FFT Style FO Flange x Thread Size (In.) Material No. Ductile Iron 8TFT Style 60 Thread x Thread Size (In.) Material No. 2,, 4 Steel, Fabricated 460FO 2,, 4 Stainless Steel, Fabricated 960FO, 4 Aluminum 660FO, 4 Ductile Iron 860FO Size (In.) Material No. 2,, 4 Steel, Fabricated 4FO 2,, 4 Stainless Steel, Fabricated 9FO, 4 Aluminum 6FO Ductile Iron 8FO Size (In.) Material No., 2, 2 Steel, Cast, High-Pressure 260 2,, 4 Steel, Fabricated 460, 2 Stainless Steel, Cast 760 2,, 4 Stainless Steel, Fabricated 960 2, 2,, 4 Aluminum 660 2,, 4 Ductile Iron 860 Style 60T Thread x Thread, with Drilled Boss Size (In.) Material No. 2 Ductile Iron 860T 2, 2 Bronze 60T 280

281 SWIVEL, ROTARY AND BALL JOINTS AND VALVES Swivel Joints continued Style 60W Butt Weld x Butt Weld Style 70FO Flange x Thread Style 70W Butt Weld x Butt Weld Size (In.) Material No. 2,, 4, 6, 8, 0 Steel, Fabricated 460W 2,, 4, 6, 8, 0 Stainless Steel, Fabricated 960W Style 70 Thread x Thread Size (In.) Material No. 2,, 4 Steel, Fabricated 470FO 2,, 4 Stainless Steel, Fabricated 970FO, 4 Aluminum 670FO, 4 Ductile Iron 870FO Size (In.) Material No. 2,, 4, 6, 8, 0 Steel, Fabricated 470W 2,, 4, 6, 8, 0 Stainless Steel, Fabricated 970W Style 80* Thread x Thread Style 70FT TTMA Truck Flanges Size (In.) Material No., 2, 2 Steel, Cast, High-Pressure 270 2,, 4, Steel, Fabricated 470, 2 Stainless Steel, Cast 770 2,, 4 Stainless Steel, Fabricated 970 2, 2,, 4 Aluminum 670 2,, 4 Ductile Iron 870 Style 70F Flange x Flange Size (In.) Material No., 4 Aluminum 670FT Style 70FTO TTMA Truck Flange x Thread Size (In.) Material No. 2,, 4 Steel, Fabricated 480 2,, 4 Stainless Steel, Fabricated 980 *Flange x thread (Style 80FO) and butt weld x *butt weld (Style 80W) units are also available. Style 80F Flange x Flange Size (In.) Material No. 2,, 4, 6, 8, 0 Steel, Fabricated 470F 2,, 4, 6, 8, 0 Stainless Steel, Fabricated 970F, 4 Aluminum 670F, 4 Ductile Iron 870F Size (In.) Material No., 4 Aluminum 670FTO Size (In.) Material No. 2,, 4, 6, 8, 0 Steel, Fabricated 480F 2,, 4, 6, 8, 0 Stainless Steel, Fabricated 980F 28

282 SWIVEL, ROTARY AND BALL JOINTS AND VALVES Swivel Joints continued Style 0* Thread x Thread Style 0F Flange x Flange Size (In.) Material No. 2,, 4 Steel, Fabricated 40 2,, 4 Stainless Steel, Fabricated 90 *Flange x thread (Style 0FO) and butt weld x *butt weld (Style 0W) units are also available. Size (In.) Material No. 2,, 4, 6, 8, 0 Steel, Fabricated 40F 2,, 4, 6, 8, 0 Stainless Steel, Fabricated 90F How to Order Swivel Joints To assure that your order is processed promptly and efficiently please specify the product number, size, materials of construction, seals and give a brief description of the swivel. Use the convenient product numbering system shown below to simplify your selections. The product number consists of two parts a model number and a suffix number. The model number can be obtained directly from the previous catalog pages and identifies the metal and swivel style. The suffix number designates size and seal material. The example shown illustrates the swivel joint. This is a fabricated steel swivel, style 20, female threads both ends. 4 size with Teflon seals. If you have a special application or are unable to located the particular swivel you have in mind, please contact Summers Rubber Company. Example: Metal Style Size Seal Material 2 = Steel, High-Pressure Cast = Bronze 4 = Steel, Fabricated 6 = Aluminum 7 = 6 Stainless Steel, Cast 8 = Ductile Iron 9 = 6 Stainless Steel, Fabricated 44 = Steel, Split Flange Design 49 = 6 Stainless Steel, Split Flange Design Alloy 20, Hastelloy, Monel units also available. Consult factory Add suffix letters below for additional styles. Refer to catalog pages fo complete listing of styles. 007 = 4 00 = 02 = 4 0 = = 2 00 = 040 = = = 8 00 = 0 = Buna N (standard) 2 = Viton = Teflon with Garter Spring 4 = EPT = Neoprene Additional seal materials including Kalrez, Chemraz, silicone, and food grade seals are also available. Consult Summers Rubber Company. End Connections: Example above has FEMALE THREADS both ends. Add F to for FLANGED ENDS. Example: 420F-040. Add W to for BUTT WELDING ends, Example: 420W-040. The following Suffix Letters are used to designate the various end connections and other features available on swivel joints: NO SUFFIX LETTER(S) = Female threads both ends F = 0# flange both ends FFT = 0# flange inlet x TTMA tank truck flange outlet FJ = for submerged use, 0# flange both ends FO = 0# flange x female threads FT FTO T TFT W = TTMA tank truck flange both ends = TTMA tank truck flange inlet x female threaded outlet = has drilled boss for guidance attachment = female threaded inlet x TTMA tank truck flange outlet = beveled for welding both ends Kalrez, Teflon and Viton are registered trademarks of the DuPont Co. Chemraz is a registered trademark of Greene Tweed. 282

283 SWIVEL, ROTARY AND BALL JOINTS AND VALVES Swivel Joints Installation Examples Special 6 stainless steel swivels in new wastewater treatment facility. Swivels make hoses easier to handle and last longer in terminals. Swivel joints are an integral part of our complete line of loading arm assemblies. This arm replaced troublesome hose in a railcar unloading operation. Loading Arms for Tank Trucks and Rail Cars Top Loaders Single Arm, Fixed Reach This simple arm incorporates only three swivel planes of rotation and is designed for use in top loading installations where the vehicle is located at a fixed distance from the riser pipe. Two swivels at the inlet permit both up-and-down and side-to-side movement of the assembly, and the third swivel allows the drop pipe to remain vertical. Primarily used to load and unload rail cars through open domes in installations where the cars can be accurately spotted, the single arm configuration can also be used for tank truck applications. Some allowance for mis-spotting is possible with the single arm and increases as the diameter of the hatch opening increases. Valve located inboard on primary arm is optional. Also available with valve located outboard to minimize drippage of viscous products after loading is completed. Adaptable to tight fill or closed system loading when equipped with additional swivel planes of rotation and/or drop hose, along with required outboard coupling or fitting. Available Sizes: 2,, 4 and 6 in steel, stainless steel, aluminum, and specialty alloys. Threaded, welded and flanged construction available. E-2-F (with valve) J-2-F (without valve) 28

284 SWIVEL, ROTARY AND BALL JOINTS AND VALVES Loading Arms for Tank Trucks and Rail Cars continued Top Loaders continued Scissor Arm This versatile arm is designed specifically for top loading installations where a variable operating range is required. The secondary arm rotates 60 in the horizontal plane, providing a spotting allowance of up to twice its length. Commonly used to handle high flow rates and withstand rough usage in tank truck loading applications, the scissor arm is also an excellent choice for rail car loading installations where cars are frequently mis-spotted. Valve located inboard on primary arm is optional. Also available with valve located outboard to minimize drippage of viscous products after the loading process is completed. Adaptable to tight fill or closed system loading when equipped with additional swivel planes of rotation and required outboard coupling, union, or other fitting. Available Sizes: 2,, 4, and 6 in steel, stainless steel, aluminum, and specialty alloys. Threaded, welded, and flanged construction available. NOTE: The scissor arm configuration is not recommended in 6 size in all steel or stainless steel due to the difficulties an operator would have handling the heavy outboard components. C-2-F (with valve) H-2-F (without valve) Bottom Loaders A-Frame Hose Loader This spring balanced hose loader offers the same advantages as the conventional A-frame arm. However, flexible hose is used instead of rigid piping on the secondary arm. Mounting heights for this style arm are shorter than those required for other hose loaders and can be staggered to achieve crossover and conformance to the API envelope requirements. A-frame hose loaders are normally stored in an upright, near vertical position, making it possible to load from both sides of the island. In addition to bottom loading, the A-frame hose loader is often used as a vapor arm in gasoline terminals and can be adapted to use in top loading and unloading applications. Available Sizes: 2, and 4 in steel, stainless steel, aluminum, and specialty metals. Minimum recommended drop hose length is approximately 60. AFH-2-F Overhead View Custom Applications Summers Rubber Company takes pride in its ability to custom design loading arms for specialized applications. Please consult the Summers Rubber Co. for assistance with your application. With our extensive experience, it s likely that our staff has already solved similar problems for other customers. 284

285 SWIVEL, ROTARY AND BALL JOINTS AND VALVES Rotary Joints These rotary joints are engineered for either general applications or special requirements. The products are grouped accordingly to guide selection based upon the characteristic of the machinery systems which they are to be used. Rotary Joints Group C These rotary joints are designed to meet the requirements of a wide range of systems as original equipment or replacement parts. Both syphon (circulating service) and single flow requirements can be met. The Type Super G rotary joint is designed for the tough corrugated board processing applications. It has proven to be a reliable performer in difficult service conditions where other joints have failed. Joint sizes from 2 to are available for all types, including ferrous and bronze materials. Type C and CS Type CR and CRF Rotating syphon for the rubber, plastic and textile industries. Sizes: 2 through Temperature: 406 F (208 C) Pressure rating: Steam 20 psi Hydraulics 00 psi Type Super G Rotary Syphon Joints These joints and the rotating syphon assemblies are designed principally for paper-making machinery and other applications needing condensate evacuation, but can be used in other applications requiring internal siphoning. Joint sizes from 4 to 4 are available in this product group. Syphon Elbows Steam, water, oil, gas threaded ends Sizes: 2 through Temperature: 406 F (208 C) Pressure rating: Steam 20 psi Hydraulics 00 psi Type CF and CSF Steam, water, oil, gas flange mounted Sizes:, 2, 2, 2 2, Temperature: 406 F (208 C) Pressure rating: Steam 20 psi Hydraulics 00 psi Hot Oil Rotary Types C, CS, CF & CSF Series 00 Corrugated board Sizes: 4, 2, 2 and 2 2 Temperature: 406 F (208 C) Pressure rating: 20 psi Series 00 Rubber and plastic calenders steam, hot water, and heat transfer fluids. Sizes: 2 x 2, 2 x 2 and 2 2 x 2 2 Steam temperature: 406 F (208 C) Pressure rating: 20 psi Water temperature: 0 F (77 C) Pressure rating: 00 psi Heat transfer temperature: 600 F (6 C) Pressure rating: 0 psi For Type C rotary joints. Bronze and stainless construction for maximum corrosion resistance. Sizes: 2 and 4 Type GR Textile and paper machine dryer For textile applications Sizes: 4 and Temperature: 42 F (27 C) Pressure rating: 00 psi For paper machine dryer applications Sizes: 2, 2 2 and Temperature: 70 F (88 C) Pressure rating: Saturated Steam 60 psi Barco Joints Sizes: 2 through Temperature: 406 F (208 C) Pressure rating: 00 psi 28

286 SWIVEL, ROTARY AND BALL JOINTS AND VALVES Rotary Joints continued Water Rotary Joints This series of joints is designed for water and brine service in cooling roll, calender and super calender applications commonly used for printing presses, as well as paper, plastics and metal foil processing. Mono and Duo-flow types are available for joint sizes from 8 to 4 within this product group. Flanged and threaded end styles are also available. Type E-7 RS and RSX Type E-7 Water, brine, high-speed cooling Sizes: 8 through 2 Temperature: 00 F (77 C) Pressure rating: Up to 70 psi RPM: 2000 rpm Air, Hydraulic, and Coolant Rotary Joints The Type E- and D rotary joints in this category are for specific applications as noted in the product descriptions. Type E- Water, brine, high-speed cooling Sizes: 8 through 2 Temperature: 22 F (07 C) -0 suffix 0 F (77 C) -04 suffix Pressure rating: 0 psi RPM: 8,00 rpm 2,00 rpm 4,00 rpm 4,000 rpm 4 2,00 rpm 2 2,00 rpm rpm Type EC Calenders paper and plastic Sizes: 2, 2 2, and 4 Temperature: 00 F (49 C) Pressure rating: 0 psi RPM: 70 rpm Air, coolants, hydraulic Sizes: 4, 8 and 2 Temperature: -20 F to 22 F (-29 C to 07 C) Pressure rating: 0 psi RPM: 600 rpm Type D Machine tools Sizes: 4 Temperature: -20 F to 22 F (-29 C to 07 C) Pressure rating: 000 psi RPM: 6000 rpm 286

287 SWIVEL, ROTARY AND BALL JOINTS AND VALVES VISI-FLO Sight Flow Indicators 00 Series threaded flapper indicator Threaded Ends Sizes: 4, 8, 2, 4,, 4, 2, 2 Available in: Bronze, 6 Stainless, Carbon Steel, Ductile Iron Flanged Ends Sizes: 4,, 2, 2,, 4, 6, 8, 0, 2 Available in:6 Stainless, Carbon Steel, Ductile Iron (available in sizes and 4 only) Model Selection Series: [4] Series, 00 Series Metal: 4[7]-2 2 Carbon Steel Bronze 7 6 Stainless Steel 8 Ductile Iron Indicator: 47[]-2 0 Plain Propeller 2 Flapper Drip Tube Low Flow ( 4 and 2 only) Size: 47-[2 ] F: Add F for flanged ends. Example: 47F-2 FJP: Add FJP for matched length unit with flanged ends. Example: 47FJP-2 [4] [7] [] [2 ] Series Metal Indicator Size Seals available from stock: Viton (standard) Teflon EPT Neoprene Buna N Indicator Components Available Four different types of VISI-FLO sight flow indicators are available: Plain When the color and/or clarity of the liquid is of prime importance. Bi-directional. Propeller The best way to show flow of opaque liquids. Also ideal for observations at a distance. Right to left flow is standard. Specify if left to right flow is required. Flapper Points in either direction to show at a glance which way the liquid is flowing. Bi-directional. Drip Tube Ideal for gravity, extremely low, or intermittent flow. Keeps liquid from dripping on glass. For vertical lines only. VISI-FLO Steel Type Series Series Plain 420FJP 20FJP Propeller 42FJP 2FJP Flapper 422FJP 22FJP Drip Tube 42FJP 2FJP Stainless Steel Type Series Series Plain 470FJP 70FJP Propeller 47FJP 7FJP Flapper 472FJP 72FJP Drip Tube 47FJP 7FJP Flanged VISI-FLO Flanged models conform to standard ANSI mounting dimensions. All models have 0 lbs. raised-face flanges. Sizes range from to 2. General Dimensions: Size of VISI-FLO: 4,, 2, 2,, 4 Size of VISI-FLO Flanged Ends: 6, 8, 0, 2 Size 2 4 Size Viton and Teflon are registered trademarks of the DuPont Co. and VISI-FLO is a registered trademark of OPW Engineered Systems. 6 2 Size 287

288 SWIVEL, ROTARY AND BALL JOINTS AND VALVES Ball Valves Brass Ball Valves For control of air, water, oil and gas in hose or pipe lines. Female NPT x Female NPT, Standard Port BBV Series High Pressure Block Body Ball Valves Full Flow Female Bolted Polypropylene Ball Valves with Nozzles 04 Stainless Steel Bolts Female NPT End x Nozzle Size (In.) No. Rated to 600 psi WOG and 0 psi steam 4 4BBV 8 6BBV 2 8BBV 4 2BBV 4 6BBV Rated to 400 psi WOG and 2 psi steam 4 20BBV 2 24BBV 2 4 2BBV Recommended Thread Working Size NPTF Pressure (In.) (In.) psi No ,20 BP ,20 BP ,20 BP ,700 BP ,000 BP6- Bolted Polypropylene Ball Valves Standard Port Valves, 4-Bolt Valve Size (In.) Description No. 2 Full Port Nozzle PV Full Port Nozzle PV Maximum working pressure: 2 psi at 70 F. Single Union Polypropylene Ball Valves Female NPT x Female NPT Stainless Steel Low Pressure Ball Valves Reduced Bore Female Size (In.) Description No. Small SS 4-bolt PV00 2 Standard SS 4-bolt PV200 Maximum working pressure: 2 psi at 70 F. Full Port Valves, 6-Bolt Valve Size (In.) No. 2 SUBV0 4 SUBV7 4 SUBV00 4 SUBV2 2 SUBV0 2 4 SUBV200 4 SUBV00 Maximum working pressure: 2 psi at 70 F. Thread NPT (In.) No. 4 4SBV 8 6SBV 2 8SBV 4 2SBV 4 6SBV 4 20SBV 2 24SBV 2 4 2SBV 288 Size (In.) Description No. 2 Small SS 4-bolt PVFP0 4 Small SS 4-bolt PVFP7 4 SS 4-bolt PVFP00 2 SS 4-bolt PVFP0 2 4 SS 6-bolt PVFP200 4 SS 6-bolt PVFP00 Maximum working pressure: 2 psi at 70 F.

289 CONVEYOR BELTS AND FASTENERS Heavy-Duty Conveyor and Elevator Belting 2 and Ply Moderate Oil Resistant Super Oil Resistant (Hot Asphalt) Skirtboard Rubber/Chute Lining Combines excellent abrasion resistance and long flex life with moderate oil resisting properties. Ideal belt for conveying oily grains and wood chips. No. Plies Belt Description x Bare MOR x 6 MOR-SC x 6 MOR-SC 22 8 x Bare MOR 0 6 x 6 MOR-SC Super Oil Resistant is specifically compounded for applications requiring moderate to very high oil resistance such as hot asphalt, foundries, oily grains, machine oils and oil-treated coal. Has same high-quality fabric characteristics as Standard. No. Plies Belt Description x 6 Hot Asphalt 0 6 x 6 Hot Asphalt Used at the point of loading for guiding product onto the center of the belt and for protecting metal parts. Also useful as lining for protecting metal and wood chutes, hoppers and troughs. Commonly found in construction, sand and gravel operations, quarries and mines and in feed and grain applications. Description (In.) 4 Skirtboard 8 Skirtboard 2 Skirtboard 4 Skirtboard Skirtboard PVC Roughtops PVC Conveyor and Elevator Belting PVC Black Crescent Top PVC 20 and 0 Black Rough textured, non-skid surface enables packages, boxes, cases and other products to be conveyed on incline or decline. Uni-ply construction and PVC compounds result to combine all the best properties for high-traction conveying and best resistance to oils, greases, water, industrial chemicals, abuse and stretch. The Green Supergrip is softer durometer for highest grab and steepest inclines. Description PVC 00 Black Roughtop x FS PVC 20 Green Supergrip Roughtop x FS Aggressive scoop pattern for high incline conveying. Crescent pattern creates hundreds of tiny buckets capable of conveying liquids along with solids. Conversely, the belt can be run the opposite direction, and the upside-down cresents convey solids while draining off liquids. Description PVC 20 Black Crescent Top PVC 200 Black Crescent Top Has proven to be the longest-wearing, best-performing, most problem-free package handling belt available today. Economical, general purpose specification ideal for a variety of roller bed, slider bed and live roller applications. Offers low stretch, high fastener-holding ability and superior rip, tear, and gouge resistance. Description PVC 20 Black C x C PVC 20 Black C x FS PVC 20 Black FS x FS PVC 0 Black C x C PVC 0 Black C x FS PVC 0 Black FS x FS Number in Belt Description indicates belt s rating for Working Tension (lbs) per inch of width. e.g. 20 Black Crescent Top = 20 lbs/inch 289

290 CONVEYOR BELTS AND FASTENERS PVC Conveyor and Elevator Belting continued PVC 200 Black Problem-free, high-performance elevator belt popular in the feed and grain industries. Also popular as heavy-duty package and bulk-product conveyor belt for both slider bed and roller bed conveyors. Description PVC 200 Black C x C PVC 200 Black C x FS PVC 200 Black FS x FS 2 Ply 0 Black and Tan Roughtop (Rubber, Gum, SBR) Incline Belts Ply Black V-Ridge Black and Tan Wedgegrip Construction is two plies of high strength, all-synthetic fabrics. Very flexible, yet stretch and moisture resistant. Tan roughtop is non-marking. No. Plies Description 2 0 Black Roughtop x Bare 2 0 Tan Roughtop x Bare Cross corrugated peaks are equivalent to small cleats; will convey on high incline. M-shaped ridges are soft, yet durable, and will self clean as they go around pulleys. No. Plies Description CN40 Black V-Ridge x FS Constructed of plies of high-strength flexible synthetic carcass and features a diamond-top surface molded in a diagonal rib design with unusually high coefficient of friction for conveying packaged and bagged goods up the very steepest of inclines. Tan Wedgegrip is non-marking. No. Plies Description 2 00 Black Wedgegrip x Bare 2 00 Tan Wedgegrip x Bare 00 Tan Wedgegrip x Bare Number in Belt Description indicates belt s rating for Working Tension (lbs) per inch of width. e.g. 20 Black Crescent Top = 20 lbs/inch 290

291 CONVEYOR BELTS AND FASTENERS Food Handling Belts Oz. White Nitrile COS Poly White Teflon COS White Solid Woven General-purpose food handling, assembly line and packaging belt; greaseproof; can be hot water and steam cleaned; resistant to food acids, fats and alkalies. Nitrile compound is also known as Buna N and Hycar. Easy-to-clean, smooth 64 cover. FDA and USDA approved. Construction features tightly woven blend of cotton and polyester plies impregnated and covered with nitrile. No. Plies Description 2 oz. White Nitrile COS oz. White Nitrile COS 4 oz. White Nitrile COS oz. White Nitrile COS Excellent for wet, sticky materials and operations involving gluing, coating, spreading; best release characteristics. The slippery top surface is created by the thin Teflon film. Carcass is strong, flexible 00% polyester. FDA and USDA approved. No. Plies Description 2 Poly 90 White Teflon COS Poly 90 White Teflon COS COS = Cover One Side Still popular conveyor and elevator belting, particularly in the food and baking industries; economical answer to many light and medium conveyor needs, especially slider bed applications. The belt is firmly woven, non-rubberized. Number of stripes usually indicates number of plies. No. Plies Description 2 Solid Woven Cotton Solid Woven Cotton 4 Solid Woven Cotton 2 Ply PVC Cover x Bare Monofilament Thermoplastic Belting Ply Gray Sticky Top x Bare Green belt features an anti-static high durometer PVC cover giving excellent abrasion resistance. Excellent for use on fiberglass and in the manufacture of corrugated box board, wafer board and particle board. Black belt is the most popular belt for checkout counter use. Black matte finish is easy on inspectors eyes. All three monofilament belts offer excellent tracking with no edge curl. No. Plies Description 2 Poly CR7 Green PVC 64 Cover x Bare 2 Poly CR7 Green PVC 64 Cover x Bare-SC 2 Poly CR4 Black PVC 64 Cover x Bare-SC 2 Poly CR7 Black PVC 64 x Bare FDA Most popular belt in the corrugated box board industry. Soft PVC compound grips product as well as Linatex. Three plies of strong monofilament fabric can handle the toughest application without stretching while providing excellent lace retention. Can be cold bonded or vulcanized endless. Ideal incline belt for a variety of heavy and abusive applications. The entire cover, down to the top ply, has sticky surface. No. Plies Description Poly CR00 Gray PVC 64 Cover x Sticky Top Number in Belt Description indicates belt s rating for Working Tension (lbs) per inch of width. e.g. 20 Black Crescent Top = 20 lbs/inch 29

292 CONVEYOR BELTS AND FASTENERS Fabrications Flanges Flanges Molded Prevents product spilling off edge of belt. Free-flowing materials are contained without troughing. Flanges can be endless or conventionally laced. Care must be taken to operate flanged belts on sufficiently large diameter pulleys. Consult factory. Heights Available: 2, 4,, 2, 2 Styles Available: Gumdrop, tapered one side, tapered both sides (all styles not available in all heights). Compounds Available: Black: SBR Nitrile PVC Butyl High Heat White: Nitrile PVC Butyl High Heat Flanges Notched Flanges Siped Notching of flanges enables a flanged belt to operate on smaller diameter pulleys. Siping of flanges enables a flanged belt to operate on smaller diameter pulleys. Flanges Siped and Drilled Flanges can be siped into relief holes to prevent any further action of slits to penetrate into the belt cover. Siping and drilling are recommended when operating flanged belt on small diameter pulleys. V-Guides Fabrications V-Guides and V-Belt Backing Used wherever conditions create a belt alignment problem. Can be molded to any belt and be made endless if desired. Bonded to cover side for flanges; bonded to underside for guide. Available in cross sections: A ( 2 W x 6 H) B ( 8 W x 7 6 H) C ( 7 8 W x 8 H) V-Guides Notched Sections A, B, C or D available. Notching enables a V-guided belt to operate on smaller pulley diameters. The V-guide eliminates tracking problems. V-Belt Backing Covers of pure gum, neoprene sheet rubber urethane, roughtop belt, white non-marking belts, etc. can be bonded to the back of V-belts. Recommended where V-belts are used as conveyor or in tandem to pull product or cable in sandwich fashion. Folded Edges 292 Fabrications Edge Finishes Premium construction for superior edge wear and carcass protection. Chemicals and bacteria may not attack the interior plies. Folded edges provide a continuous surface from the top of the belt around the edges. Molded Edges Rubber edging vulcanized to cut-edge belting. Protects the belt fabric from bacteria and damaging chemicals, ideal for food-handling applications. Also used for additional protection from edge wear.

293 CONVEYOR BELTS AND FASTENERS Fabrications Rubber, Nitrile, Butyl and PVC Cleats All cleated belts can be furnished as follows: A Indented from edge C Cut-outs or voids B Notched for troughing idlers or curved pans D Cut down to intermediate heights Standard I Cleats Mini Cleats For conveying up steep inclines. Available in white FDA or black oil-resisting nitrile, black SBR rubber, black and white butyl. Cleats are hot molded into the belt surface (not cold bonded or cemented on). Smooth merging of cleat and belt cover for easy cleaning. Cleats can be molded to the belt surface on any center, to fit a wide variety of applications. Cleats come in heights from 2 to (Beefy Cleats to 6 ). (For taller cleats, a two-part cleats, a two-part construction is used.) Mini-cleats are low-profile cleats ideal for moving products up inclines in lightduty applications. Unique shape allows for standard idler support on returns. Dimensions are 6 high, 6 wide at base and 8 radius. Steel-Reinforced Cleats Super-strong cleat for the most rugged applications. Each cleat features a steel reinforcement oriented to best counter the forces encountered in a particular application. Curved PVC Cleats PVC Scoop Cleats Ideal cleat for many incline applications requiring foodgrade belting. Cleats up to tall are available in 4 and 0 configurations. Cleats can be applied to belts 6 to 48 wide and on centers as close as 4 2 at 0 and 9 at 4. White PVC cleats in an angled scoop form to improve capacity up steep inclines. Acceptable for food-handling applications. Available in 2, 2 2, and heights, the cleats are hot welded into the belt surface for a smooth, seamless finish. Beefy Cleats High Incline Cleats Lug Cleats Beefy Cleats feature an extraheavy cross section designed for heavy-duty, rugged applications. Thickness is double that of a Standard I Cleat. Available in heights from to 6, with backup braces available with 2 and heights. Aggressive scoop cleats for high-capacity conveying on steep inclines. C cleats are available in heights from to, and S cleats come in heights from 4 to 4 2. Rugged cleats are hot vulcanized into the belt cover for long service. Lug construction features rugged V-belt shapes for impact resistance. Available in A( 2 W x 6 H), B ( 8 W x 7 6 H), and C ( 7 8 W x 8 H) cross sections. PVC Vinyl Cleats PVC cleats are welded to PVC belting to produce a rugged, economical combination ideal for wet, oily or acidic conditions. Available in black or white FDA compounds and can be spaced on any centers, indented, notched, cut down to intermediate heights and contain cut-outs. PVC Extruded Cleats Extruded PVC cleats are conveniently packaged for OEMs to manufacture their own PVC cleated belt. PVC cleats are furnished in convenient 00 rolls. (W) Min. (H) (T) Base Pulley Height Thickness Width Dia. (In.) (In.) (In.) (In.)

294 CONVEYOR BELTS AND FASTENERS Fabrications Splicing Endless Vulcanized A hot-vulcanized splice is stronger and more sanitary than a mechanical (laced) joint. Endless splicing eliminates fastener pull out and tearing the belt. Ideal for food processing industries and where metal lacing can mar the product. Endless Prepared Belts are supplied with laps already prepared to desired length but not vulcanized, enabling customer to splice endless on the conveyor or drive. Hot or cold cements with instructions are available. Finger Splice A proven heavy-duty splice for single ply belting utilizing polyurethane as the bonding agent. Lap area is same thickness as the belt and uniformly smooth. Multiple Finger Splice Similar to the Finger Splice but for multi-ply belts. Staggered die cut fingers are vulcanized together to create a strong, extremely flexible splice. Fabrications Mechanical Fasteners Lacing Standard Types: Alligator, Clipper, Flexco, Minet and others. Mechanical fastener joints with hinge pins provide an easy, quick and secure method of joining belt ends. Avoid lacing problems by utilizing our factory lacing experts. Covered (Hidden) Lace Lacing is hidden by the cover of the belt to allow the ease of installation provided by a mechanical splice with the smooth operation of an endless belt. Product is protected from marring from the mechanical splice area. Splice can be covered with rubber or abrasionresistant urethane. Spiral Lace Ideal mechanical splice for small-pulley, low-profile applications. Unique hinge design allows use on pulleys and nose bars as small as 8 diameter and as thick as 6. Resists corrosion and heat as high as 46 F. Lace is factory installed by insertion between belt plies. Overflap Lace Recessed Lace Top cover of belt is skived back and mechanical fastener installed. The overflap is spliced back over the splice area, providing a smooth conveying surface. Product being conveyed is protected from marring by the fastener. Mechanical splice area of belt is recessed below the level of the belt cover. The recessed lace keeps the product being conveyed from coming in contact with the lacing. Plastic Rivet Fasteners Come in white and black compounds for a variety of conveying situations. Fasteners feature beveled edges and counter-sunk pockets in bottom of fastener to protect rivets. Fasteners are either installed by the factory or in the field with special tools. Longitudinal Splicing For extra-wide belt requirements. Longitudinally spliced belts can be made endless and/or V-guided. The lap area is same thickness as the belt and uniformly smooth. Any belt width is attainable by using multiple splices. 294 Fabrications Longitudinal Splicing Longitudinal splices can be made in a variety of compounds, including woven PVC, thermoplastic, roughtops, all impression tops, urethane covered, and black rubber in all thicknesses. Longitudinally spliced belts can be fitted with flanges or V-guides if desired.

295 CONVEYOR BELTS AND FASTENERS Fabrications Hole Punching, Perforating Hole Punching Automatic punching assures clean-cut, tight-fitting bolt holes with accurate spacing for buckets on elevator belting. Perforated V-Guided Belt V-guides can be placed on a perforated belt to aid in tracking. The entire belt can be perforated, leaving a small strip onto which the V-guide is fastened. Used in vacuum and drainage applications. Perforating For vacuum, suction or drainage applications, Summers supplies perforated belts with a wide variety of hole sizes. Perforations are clean with no fuzz or tearing. Summers sources has over 00 dies for hole punching patterns. Perforated Cleated Belt Perforated belt can be combined with cleats to create a vacuum belt or a belt that can drain a product while conveying on an incline. Perforations can be of any size and cleats on any centers. Notching Cleats Fabrications Notching Cleats can be furnished with notches for troughing idlers or curved pans. Notching Chevron Cleats Notching chevron patterns allows the use of the belt on smaller diameter pulleys. Belts with notched chevrons are often known as roofer s belt. Notching V-Guides Notching enables a V-guided belt to operate on smaller pulley diameters. The V-guide virtually eliminates tracking problems. Notching Flanges Notching of a flanged belt enables a flanged belt to operate on smaller diameter pulleys. Grooving Lateral Fabrications Edge Finishes Grooving across the width of the belt can be used to convey liquid or other free-flowing material. Grooving Longitudinal Grooving can create an economical self-flanging belt for carrying free-flowing material without spillage. Precision Grinding Fabrications Precision Grinding For applications requiring extreme thickness uniformity across the width of the belt as well as the length. Summers offers precision grinding. Accurate to ±.00, precision grinding is available on rubber as well as urethane belts. Often performed on belts used in die stamping applications, precision grinding minimizes any imperfections that might be in the belt cover. 29

296 CONVEYOR BELTS AND FASTENERS Fabrications Urethane Cleats Urethane Standard Cleat Available in heights from 2 to 6, this is a super-strong, abrasion-resistant cleat. Angled backup support enables the cleat to carry a heavier load. Urethane Square/Rectangular Cleat Strong, abrasion-resistant urethane cleat. Available in any cross section. Urethane Bolt-On Cleat Similar to Tatch-A-Cleat, only made of urethane, this strong cleat is quickly attached and just as quickly removed for replacement. Ideal for highly abrasive applications where the cleats face a high amount of wear. Urethane Two- Cleat For heavy-duty, high capacity applications. Unique two-part construction consists of a rubber foot hot molded to the base belt, and a bolted-in urethane cleat. Cleat can be replaced in high-wear applications. Heights from to 4 2. Urethane Cold-Bond Cleat With or without cotton base, this cleat is designed for bonding to any base belt. Urethane Chevron Cleat A wide variety of custom patterns are available for durable incline conveying. Call for details. Fabrications Urethane Specialties Urethane-Covered Belts Urethane covers can be applied to a wide variety of base belts for differing conveying situations. Various urethane thicknesses, hardnesses and colors are available. Urethane Sheets/Molded s Urethane sheets are available in fabric-back or metal-back and any standard size, thickness or color. Urethane s moldable capabilities make it ideal for custom-molded parts. Various durometers and colors are available for your particular application. Urethane-Covered Wire Mesh By combining the high wear and abrasion resistance of urethane with the strength of steel, Summers distributes an almost indestructible belt. Ideal for stamping operations, die cutting, belt sanding units, and glass cullet. Seamless Urethane Pulley Lagging Summer s unique seamless pulley lagging enables pulleys to be quickly lagged without any seams. The smooth surface means smoother, quieter conveyor operation and longer lasting lagging. (Volume orders only.) Urethane V-Belt and Timing Belt Backing Fabricated to desired thickness and durometer. Urethane Flanges All standard heights are available. Slitting (siping) is recommended. 296

297 CONVEYOR BELTS AND FASTENERS Belt Accessories Alligator Lace Summers supplies a complete inventory of sizes, lengths and types. Alligator Plastic Rivet Fastener Rugged plastic fastener for black and food grade belts. Installed in the factory or in the field with special tools. Belt Dressing Used to increase traction between belt and pulley and as a preservative. Liquid Aerosols Bar Neatsfoot Oil Belt Cleaners Designed to clean white food handling belt. Acetone Toluene Belt Scrapers (Urethane) Available in various hardness and compounds, including food grade. Clipper Lace Full range of sizes, types, lacers, accessories. Edge Sealing Used to seal belt edges to protect against fraying and moisture penetration. Latex Urethane Elevator Bolts and Nuts To join elevator belt ends. Overlap-butt joint-pad joint; most popular sizes in stock. Elevator Buckets A wide variety of sizes and compounds are available for most any elevating applications. Flexco Fasteners Plate type Rivet type Hinged type Leader Wire Pins Recommended for belts 48 and wider to make inserting the nylon-covered cable easier. Comes complete with leader wire, connecting sleeve, and nylon-covered cable pin. Minet Fasteners Mechanical fasteners for a wide variety of conveying applications. Plastic Fasteners Will beat metal detector units; ideal for food industry; can be steam sterilized; resists most chemicals; easily installed. Constructed of a plastic nylon suitable for lightweight conveyor belting. It is economical compared to vulcanizing and can be separated for fast installation and removal. Unlike conventional metal fasteners it is safe to operators and will not damage goods that are conveyed. Available in packages sufficient to lace 24 -wide belts. Sizes B, C, and D. A reusable template is required for each use. Pulley Lagging Smooth, seamless urthane, drive screws, lagging cement. Pulleys Conveyor/Elevator Winged Pulleys Paper Pulleys Rubber Splice Kits Component materials furnished for splicing belts endless in field or shop. Sewing Machine Belt Round Leather VOV Type Aerosols to Lubricate Silicon Spray Spiral Lace Mechanical fastener vulcanized into belt. Allows use on extremely small diameter pulleys. Tatch-A-Cleat Bolt-on cleats in a variety of compounds including rubber and PVC. Quickly attaches to belt and is easily removed. Urethane Round Belt Solid Hollow Plastic Fasteners Urethane Splice Kits To cover lacing so product will not mar. 297

298 CONVEYOR BELTS AND FASTENERS Conveyor Terms and Definitions The following schematics with terms and definitions are included here to help enable Summers Rubber Company to better discuss your conveyor belt needs with our salespeople in order that the right belt is selected for the application. Conveyor Terms Angle of Incline The degree a conveyor is tilted from horizontal. Drive Pulley Pulley connected to a power source used to drive conveyor. Usually the drive pulley is the head pulley, but on some types of systems, including many package handling conveyors, the drive pulley is located underneath the conveyor. Gravity Takeup Device used to remove slack and stretch in a conveyor belt. A free weight is suspended from an idler on the return side of the belt. The takeup is free to lower as needed to remove any slack as the belt is operated. The gravity takeup is usually located as close to the drive pulley as possible. 298 Head Pulley Pulley at discharge end of belt. The head pulley is usually powered by conveyor drive source. Pulley pulls belt along the conveyor. Return Idler Idlers used to support belt as it passes underneath the conveyor structure. Roller Bed Free-wheeling, usually closely spaced rollers used to support the loaded belt. Screw Takeup Device utilizing a bolt construction used to lengthen the conveyor to remove slack in the conveyor belt. By moving the bolt, the tail pulley is pushed away from the head pulley thus removing slack from the belt. Slider Bed Smooth, flat surface (usually steel or wood) on which the loaded conveyor belt rides. Snub Idler Idler used to increase the amount of belt in contact with the pulley or to deflect the belt in a different direction. Snubbing a belt near a pulley can increase the effectiveness of the pulley. Tail Pulley Pulley at the beginning of the carrying run of the conveyor. The tail pulley is usually free wheeling. Troughing Idlers Grouping of idlers on the carrying side of the conveyor designed to make the conveyor belt curve into a cupped shape, increasing conveyor capacity. Troughing idlers are usually 20, or 4.

299 GLOVES, RAIN GEAR, LUBRICANTS AND MISC. SUPPLIES Molded/Extruded Rubber Goods Tubing/Extrusions Molded Dies available for thousands of shapes solids or cellular materials compounds to meet special service requirements. Companion splicing molds available. Injection, compression or transfer molded standard polymers or custom compounds prototypes or volume production to meet your needs! Grommets Latex Dipped Vibration Mounts Bellows, flexible protective covers and latex covered wire/metal components. Fast production, low cost. Choose from rubber latex or neoprene latex including low temperature compounds. Specialities It is not practical for us to list the many items used for special service. Let us help you where special material is required. Gaskets, rubber strip lathe cut and other custom fabricated components made to order. Strips Die Cut Custom Made Rubber 299

300 GLOVES, RAIN GEAR, LUBRICANTS AND MISC. SUPPLIES General Purpose Gloves Nitrile Coating over 00% Cotton Interlock Lining Vinyl Coated Knit Lined Rubber Coated Flock Finish The comfort of cotton, the protection of nitrile combined ruggedness in a medium duty glove. Extra comfort. Superior flexibility and finger dexterity. Outstanding dry grip. Machine washable. Applications Assembly, inspection, light fabrication material handling, shipping and receiving packaging, maintenance, sheet metal and parts handling. Palm Coated Knitwrist Comfortable. Long wearing. Excellent dexterity. Superior grip. Machine washable. Liquid repellent (but not chemical resistant). Applications General use, shipping, receiving, assembly, inspection, packaging, maintenance. Slip On 22- Economical replaces heavy cotton and leather palm gloves for handling smooth, slippery or abrasive objects. High cut resistance. Extra comfort. Applications Handling smooth, slippery or sharpedged materials like glass, sheet metal, castings, cores, tile, block and veneer. Fully Coated Knitwrist PVC Coated Premium Quality Line Chemical Resistant Gloves Neoprene Coated Knit Lined Premium quality unique PVC/nitrile blend rough finish provides outstanding chemical resistance, wear and flexibility. Nylon particles in unique rough finish increase cut and abrasion resistance. Added flexibility and comfort. Excellent wet grip. Applications Petrochemicals and refining, handling equipment and abrasive materials coated with acids, caustics, solvents, grease and oil. Jersey Lined, 2 Fully Coated Gauntlet 4-42 Broad protection reinforced neoprene coating provides better all-around resistance to abrasion, cutting and chemicals than most other glove coatings. Comfortable. Applications Refining and petrochemicals; degreasing; plating; metal fabrication; handling oils, acids, caustics, alcohols and many solvents; HazMat work. Fully Coated Knitwrist Fully Coated Gauntlet Fully Coated Gauntlet

301 GLOVES, RAIN GEAR, LUBRICANTS AND MISC. SUPPLIES Chemical Resistant Gloves continued Neoprene Coated Heavy-Duty Line Unsupported Premium Quality Nitrile Line Premium quality wears up to 0% longer than ordinary neoprene coated gloves. Excellent wet grip. Maximum protection for handling oils, acids, caustics, alcohols, and many solvents. Fabric lining improves snag and puncture resistance. Applications Petrochemicals and refining, chemical transport, HazMat work. 4 Fully Coated Gauntlet Fully Coated Gauntlet 9-98 High performance outstanding combination of strength and chemical resistance. Tough Nitrile compound. Resistance to degradation will not weaken or swell like rubber and neoprene in many solvents, caustics and animal fats. Strong chemical resistance superior to neoprene and rubber in most solvents, including aromatic and petroleum. Fewer skin problems. Large selection of lengths and thicknesses, multiple sizes and choice of flock lining. Applications Chemical processing, oil refining, petrochemicals; food processing (red meat, poultry, vegetables, fruit, dairy and canning); aerospace and automotive degreasing; automotive assembly and painting; machining operations using cutting oil and coolants; metal fabrication; graphic arts; printing clean-up; furniture manufacturing; battery manufacturing; electronics (semi-conductors, circuit board manufacturing. Length Length Length Length Length 7-7- Special Purpose Gloves Raised Finish Winter Monkey Grip More gripping power textured surface provides an excellent grip for easier, safer handling of wet and dry materials. Superior cold weather protection. Raised finish vinyl coating. Non-woven insulation. Applications Construction; cold storage; winter transportation; yard and field work; freight handling; trash collection; surveying. Fully Coated Safety Cuff 2-7 Winter Monkey Grip Chemical resistant; vinyl coated, caramel color; curved fingers, wing thumb and general softness make this glove very comfortable and easy to wear. Keeps hands warm. Long wearing. Comfortable. Applications Winter transportation; yard and field work; cold storage; unheated warehouses; construction. Fully Coated Safety Cuff 2-9 Monkey Grip is a trademark of Ansell Edmont Industrial Inc. 0

302 GLOVES, RAIN GEAR, LUBRICANTS AND MISC. SUPPLIES Clothing Jacket with Attached Hood Fly Front Overall Dry N Lite features a lighter coating of ribbed PVC on a non-woven polyester base fabric for economy and lightweight protection from foul weather conditions. Sizes range of S to XL. Imported. Overall-S -M -L -XL -XXL -XXXL Parka H-S -M -L -XL -XXL -XXXL Rainfair Chem-Tech I Green Jacket with Detachable Hood Green Plain Front Overall Chemical suit and coverall incorporates the latest in personal protection technology. The tapered collar is larger than standard collars for better protection from overhead leaks and spills. ChemSuit-S -M -L -XL -XXL -XXXL -XXXXL ChemOverall-S -M -L -XL -XXL -XXXL -XXXXL Ecomony Three-Piece PVC Rainsuit This economical.mm Three- Piece Rainsuit is constructed of PVC on polyester fabric. Jacket features a detachable hood, two flap pockets, comfortable corduroy collar and cape back ventilation. Overalls are fly front and all seams are heat sealed. Yellow. Suit-S -M -L -XL -XXL -XXXL -XXXXL 48 Long PVC Raincoat This 48 Raincoat is constructed of.mm PVC on polyester fabric. Its economical design features two flap pockets and cape back ventilation. All seams are heat sealed. A detachable hood is included. Yellow. Coat 48-M 48-L 48-XL 48-XXL 48-XXXL 48-XXXXL Rainfair Chem-Tech I and Dry N Lite are registered trademarks of Rainfair Inc. 7 Yellow Overshoe Economical and long-wearing overshoe slips on easily over work shoes. Flexible rubber material, knit lining and adjustable top strap for comfortable fit. Black cleated outsole for traction on slippery surfaces. Perfect all-purpose boot for just about any industrial application including construction, road crews, sanitation and municipalities. Slicker Y-8, Y-9, Y-0, Y-, Slicker Y-2, Y-, Y-4, Slicker Y- and Y-6 02

303 GLOVES, RAIN GEAR, LUBRICANTS AND MISC. SUPPLIES Maintenance, Repair and Hose Room Accessories Teflon Sealants Thread Sealant Paste Can Size No. 2 Pint LCTS Pint LCTS2 Industrial Teflon Tape (White)* Size/Length (In.) No. 2 x 20 TTB-0 4 x 20 TTB-7 *Meets Miliary Specification, MIL-T-2770A. Epoxy Repair Sticks Pre-measured, versatile twocomponent epoxy putties that fill, bond and patch a variety of surfaces and metals quickly, even in difficult environments. Epoxies bond to metal, concrete, wood, ceramic and plastic. Use for emergency repairs to tanks, drums, pipes, castings, fittings, etc. Sticks cure in hour. Metal Stick, 2 oz Lubricants and Sealants Pipe Joint Compound Seals pipes to 000 psi; prevents galling and corrosion; outperforms Teflon tape; will not shred; non-hardening. Pint Brush Can 8004 High Pressure Hydraulic Sealant Low viscosity brown sealant; designed for fine threaded air and hydraulic fittings; used to augment seal achieved with tapered fittings or to replace their use with straight fittings. 0 mil HP690 Instant Pipe Sealant with Teflon High viscosity, fast curing paste; works on inactive surfaces such as stainless steel; withstands temperatures to 400 F (200 C). 0 mil PS670 Thread Sealant with Teflon Seals pipes to 000 psi; prevents galling and corrosion; outperforms Teflon tape; will not shred; nonhardening for easy disassembly. Pint Brush Can 806 Fast Orange Hand Cleaner Cleans with natural solvents extracted from oranges; removes tough grease and grime without petroleum solvents; fresh citrus scent; with pumice. Gal. Bottle w/pump 228 Cleaning Solvent All Purpose s Cleaner Removes oils, carbon and grease from machinery and precision parts; leaves no residue; special 2-way valve for spray or pin-point application; non-flammable; contains no CFCs. oz. Aerosol 227 Form-A-Gasket Dries quickly to a hard set; recommended for rigid, permanent assemblies. oz. Tube 8000 Teflon is a registered trademark of the DuPont Co. Fresh Orange, Form-A-Gasket, Form-A-Gasket No. 2, Solvo-Rust and Locks Nuts are trademarks of Loctite Corp. Form-A-Gasket No. 2 Improves gasket seal on non-rigid, vibrating assemblies; slow drying, flexible setting; withstands pressures to 000 psi; black. oz. Tube 800 Solvo-Rust Super Penetrating Oil Releases frozen nuts and bolts; freed parts remain lubricated; safe on painted surfaces; contains no CFCs. oz. Aerosol 0060 Locks Nuts Removable Threadlocker General purpose thread locking; prevents vibration loosening; replace lock washers, set screws and plastic inserts; disassemble with hand tools..69 fl. oz. Extreme Threadlocker Gasket Remover Removes baked on gaskets, carbon, paints and silicone; works in minutes; eliminates scraping; contains no CFCs. 8 oz. Aerosol Can 007 O-Ring Making Kit Makes instant O-rings; contains two gm tubes Super Glue Instant Adhesive, cord stock ( 2, 6, 8, 4 diameters), cutting fixture, added bonus: free sample Quick Gel Non-Run Instant Adhesive. Sturdy Kit Box O-Ring Kit 0

304 GLOVES, RAIN GEAR, LUBRICANTS AND MISC. SUPPLIES Maintenance, Repair and Hose Room Accessories continued Lubricants and Sealants continued Belt Dressing Restores moisture to belts; increases gripping power; silences squeaks; increases belt life; contains no CFCs. 2 oz. Aerosol 006 Gear, Chain and Cable Lubricant Lubricates and prolongs life of gears, chains and wire rope; repels dirt, sand and dust; contains no CFCs. 2 oz. Aerosol 000 Anti-Seize Lubricant Lubricates in high temperature, heavy pressure and corrosion environments; works to 600 F; eliminates corrosion, seizing and galling. 8. oz. Aerosol SL90 Nickel Anti-Seize Lubricant Lubricates in high temperature, heavy pressure and corrosion environments; works to 400 F; premium copper-free, acid resistant lubricant. lb. Brush Can SL9 Silicone Lubricant Lubricates all sliding surfaces; stops squeaks and binding; won t mar paint or plastic surfaces; non-gumming; waterproofs; contains no CFCs. oz. Aerosol Pure Silicone Pliobond 20 General purpose adhesive delivers permanently flexible bonds. For seaming, splicing and bonding of gaskets, rubber matting, belts and hose to rubber, wood, metal, some plastics, glass and fabrics and to themselves. Provides permanent, flexible bonding. Can be brushed, spread or roller coated. Will not get hard or brittle with age and resists most acids, oil, gasoline, grease and water and salt. Can Size No. 2 Pint Brush Top Can PBC-20 Pint Can PC-220 Quart Can PC-20 Gallon Can PC-420 Chlor-Free Degreaser Non-chlorinated, nonozone depleting cleaner provides effective cleaning power. Fast evaporating. Offers high permissible exposure limit and is suitable for most applications permitting low flash point cleaners. This product is labeled extremely flammable. Read and observe the special usage warning on the label. Do not apply while equipment is energized. oz. 020 Natural Degreaser Naturally formulated, biodegradable cleaner/ degreaser designed for every day maintenance needs. Superior for tackling grease, tar, oil, adhesives and tree sap. Advanced technology blend is VOC free and evaporates without leaving a residue. 20 oz. 400 Wasp & Hornet Killer PLUS 20 oz. Wasp Killer Pliobond is a registered trademark of Ashland Oil, Inc. Chlor-Free and Natural Degreaser are trademarks of CRC Industries, Inc. 04

305 GLOVES, RAIN GEAR, LUBRICANTS AND MISC. SUPPLIES Maintenance, Repair and Hose Room Accessories continued Upside Down Marking Paints Nylon Cable Ties Nylon Cable Ties are available in lengths from 4 up to 48. They will satisfy binding requirements from 6 to and loop tensile strength from 8 to 7 lbs. Can be used to bundle hose or secure identification tag. Sold in bag quantities only. Designed to clearly and effectively mark the location of underground utilities and are the professionally preferred markers at construction sites. These specially formulated marking paints provide the best features needed for any marking job. Apply with any of our convenient equipment or accessories. Colors meet the APWA One Call International Color Standards. Surfaces: Use Upside Down Marking Paints to identify and code surfaces such as: metal, concrete, asphalt, gravel, soil, trees and grass. icularly safe on turf grass, fields and golf courses. Applications: Construction, utility, recreational, municipal and landscaping sites, golf courses, nurseries and surveying. Tie Length Package (In.) Quantity No CT4 00 CT 7 00 CT CT8 00 CT 4 00 CT CT CT CT48 Premium Anti-Wear Hydraulic Oil Product Color Safety Red Caution Yellow Caution Blue 20-6 White Red/Orange Fluorescent gallon pail with pourable spout. AW-46 0

306 FAX: SAFETY Hose and Hose Coupling Safety THE VERY PROPERTIES THAT MAKE COMPRESSED GASES USEFUL IN ALMOST EVERY AREA OF MODERN LIFE CAN ALSO MAKE THEM DANGEROUS WHEN MISHANDLED. YEARS OF EXPERIENCE WITH COMPRESSED GASES HAVE LED TO PRACTICES AND EQUIPMENT WHICH, IF EMPLOYED, RESULT IN COMPLETE SAFETY. * All hose and couplings have been carefully engineered to meet specific requirements with large safety margins. If hose or couplings are not used in correct applications or are incorrectly applied, accidents and downtime can result. It is up to the end user to inform Summers Rubber Company of the application and pressures involved when ordering hose assemblies and up to Summers Rubber Company to supply the right hose and coupling for that application. When in doubt, we are here to help you with a proper coupling recommendation.. AIR HOSE COUPLINGS This form of energy can be one of the most dangerous because it is used in so many applications and, when mishandled, can have more serious results than fluids. Air, as a gas, is compressible (fluids press only against hose or vessel walls and lose little volume under pressure). When pressurized air suddenly releases, it does so with explosive force and can cause rapid hosewhip... which can do serious physical harm to personnel or damage to nearby objects. This is why the selection of proper hose and couplings for air lines is so important, along with their proper installation and maintenance. Never take for granted that a coupling is installed properly or a clamp fully tightened on an air hose check it regularly and use safety devices (see paragraph 4). 2. STEAM AND GAS The same rules apply for steam and gas, but, because these are inherently more hazardous materials, personnel tend to treat hose and couplings on these lines with more respect and care. Checking clamp tightness is very important with steam hose, where it is not unusual for clamps to loosen in service, in which case they MUST BE RETIGHTENED! Safety devices should also be used.. FLUID HOSE COUPLINGS Again, nothing should be taken for granted in particular, check clamps for tightness each time the lines are used especially when petroleum products or other hazardous liquids are involved. Large diameter hose, when suspended, can also be quite dangerous if it drops unexpectedly due to a coupling pull-out or sudden disconnection. With a heavy fitting or clamp, plus the weight of the hose itself falling from any significant height, it can cause injuries or damage. Be sure to use safety devices. 4. ALL HOSE ASSEMBLIES All hose assemblies should be treated with respect as potential hazards. Worn-out fittings should be replaced. Retaining devices such as clips, cables or canes should be used. Clamps should be checked regularly. Product Selection Many of the products in this catalog are used in hose assemblies in a variety of applications. The safety of any hose assembly rests on the proper selection, installation, testing and use of each product. The safe use of any product in this catalog is dependent upon the correct selection of the hose, fittings and method of attachment. To ensure such a proper selection, the user must inform Summers Rubber Company of the application and pressure involved when ordering hose assemblies. The use of the S.T.A.M.P.E.D. (Size, Temperature, Application, Media, Pressure, Ends, Delivery) will help in the proper selection of hose assembly components. The selection of couplings and clamping devices is the responsibility of the purchaser or user, based upon the hose manufacturer s recommendations. If the purchaser or user is uncertain about the use or application of a product, Summers Rubber Company stands ready to provide information, including test results (if available), coupling and clamping recommendations and other data to help resolve those matters. (See worksheet on page.) Installation To achieve a safe and reliable assembly, proper installation procedures must be followed. Each component of the assembly has a part in determining these procedures. The purchaser or user must follow proper procedures. If the purchaser or user has any questions regarding installation, please contact the Summers Rubber Company. Testing Summers Rubber Company recommends that all hose assemblies be tested in accordance with the hose manufacturer s recommendations. Re-testing and Inspection Summers Rubber Company recommends inspection and re-testing of hose assemblies on a regular and consistent basis in accordance with the hose manufacturer s recommendations. The application determines the regularity of the inspection and re-testing schedule. Any worn-out fittings, damaged hoses or missing safety devices should be replaced immediately. Bolt-style clamps must be checked and retightened on a regular and consistent basis. * Handbook of Compressed Gases 06

307 Get It Right Get It Now! Summers service begins with knowing our products and your needs Summers Rubber has become the leading regional source of industrial hose products by combining a unique dedication to customers needs with an in-depth, up-to-date knowledge of hoses, hose components, fittings and accessories. It s a philosophy that has guided the company s growth under three generations of Summers family leadership. A continuing dedication to become a partner in productivity by applying our more than,000 years of combined experience to help our customers reduce costly maintenance and downtime. Today, as part of our focus on ISO 9002 compliance, each Summers employee undergoes extensive training to provide customers with complete, current information as well as problem-solving advice. We provide knowledge about products that can deliver improved performance, greater durability and significant cost-savings to you. Let your computer do the work Electronic Data Interchange, now available from Summers Rubber, can speed up ordering and reduce errors while saving administration time, cutting labor requirements and slashing costs for fax, phone and mail. Requiring no more than a computer, translation software, a communications system and an electronic mailbox facility. Summers EDI program offers the ultimate in ordering efficiency. Convenient counter service Each of Summers eight locations is fully prepared to handle emergency walk-in needs with a trained service counter crew backed by an extensive inventory of popular products. Right away, you can get the right hose and right fittings to minimize costly downtime. On-site services to save you time and money Summers helps you improve the efficiency and productivity of your purchasing and maintenance functions with the following on-site services: Hose assembly preventive maintenance tracking. Special stocking agreements. Service level reports. Custom labeling. Hose assembly pressure testing and certification. Kit assembly and packaging. Inventory management. Delivery service. Plant surveys for application improvement and safety. Store room inventory reduction analysis. Just In Time delivery for MRO and OEM programs. Private labeling of hose and fittings.

308 Call any convenient Summers Rubber location Certified ISO 9002 Internet: Summers Rubber Company 2 Berea Road, Cleveland, OH 44 Phone: Toll-free: Fax: Summers Rubber of Findlay 22 Lima Avenue, Findlay, OH 4840 Phone: Toll-free: Fax: Summers Rubber of Eastlake 00 Lakeland Boulevard, Eastlake, OH Phone: Toll-free: Fax: Summers Rubber of New Castle, Quality Hose & Supply Division 0 North Liberty Street, New Castle, PA 602 Phone: Toll-free: Fax: Summers Rubber of Mansfield 60 West Longview Avenue, Mansfield, OH 4490 Phone: Toll-free: Fax: Summers Rubber of Marietta Route 7 & Tennis Center Drive, Marietta, OH 470 Phone: Toll-free: Fax: Summers Rubber of Dover RD, Dover, OH Phone: Toll-free: Fax: Summers Rubber of Akron 489 Kelly Avenue, Akron, OH 4406 Phone: Toll-free: Fax: Our Vision To set the standards in our industry for customer satisfaction and operational effectiveness. To attract, retain and recognize great people. To become the recognized name to our customers for our products and services. To constantly invest in our human and physical resources. To be aligned with the best manufacturers worldwide for our products. To be the dominant distributor of our products and services in Ohio, Western Pennsylvania and West Virginia.