TX-W32 & TX-W42 Touch LCD Display

Transcription

1 TX-W32 & TX-W42 Touch CD Display

2 Table of Contents Preface FCC Declaimers...4 WEEE...5 Hg...5 Precautions Notice...6 Cautions When Setting Up...6 Cautions When Using...7 Cleaning and Maintenance...7 Notice for the CD Display...8 Chapter 1: Product Description 1.1 Package Contents Wall Mounting Installation Preparation emoving the Base Stand Wall Mounting emoving the Handles CD Display Overview Front View and Keypad Buttons ear View emote Control emote Control Buttons Installing the emote Control Batteries emote Control Signal...14 Chapter 2: Making Connections 2.1 Connecting the AC Power Connecting Input Source Signals Connecting a Computer...16 Using Cables...16 Using Cables...16 Using USB Cables Connecting a Camera or Video Device...18 Using CVBS Cables...18 Using YPbPr Cables...18 Using S-Video Cables Connecting a Stereo Amplifier...19 Connecting an Audio Device Connecting Multiple CD Displays...21 Chapter 3: Using the CD Display 3.1 Turning on the Power Using the Keypad Using the emote Control Table of Contents

3 3.2 Selecting the Input Source Signal Using the Keypad Using the emote Control Adjusting the Volume Using the Keypad Using the emote Control Muting the Volume ocking the OSD Menu Using Picture-in-Picture (PIP) PIP Options PIP Swap...26 Chapter 4: Touch Screen Properties 4.1 Installing the CD Display Driver Windows XP Installation Windows 7 / Windows Vista Installation Using the Touch Screen Single-Touch vs. Multi-Touch Finger Gestures Touch Screen Extras Windows Pen and Touch Settings...31 Chapter 5: On Screen Display Menu 5.1 Using the OSD Menu OSD Menu Tree...34 Chapter 6: Adjusting the CD Display 6.1 Brightness Setting Colour Setting Colour Temperature Image Setting ( only) Image Setting (Video signals) Aspect atio PIP Setting Anti-Burn-In OSD Setting Audio Setting Other Setting Input Select...50 Chapter 7: Appendix 7.1 Warning Messages Troubleshooting Transporting the CD Display...53 Chapter 8: Specifications 8.1 Display Specifications Display Dimensions TX-W32 Dimensions TX-W42 Dimensions...55 Table of Contents 3

4 Safety Information FCC Declaimers This FCC Class-B compliant digital device complies with the Interference- Causing Equipment egulations of Canada. This device complies with Section 15 of the FCC listing. The operation procedures must meet the following conditions: (1) the device must not cause any damaging interference; and (2) this device must accept any received interference, including any unpredictable interference that may possibly occur. Dear users, This device has passed the Class B digital service regulations and complies with Section 15 of the FCC listing; these are intended to provide reasonable warranty against damaging interference for home use. This device will produce, use, and emit radio frequency energy; therefore installation or use without following the instructions given may cause damaging interference to radio communication. Nonetheless, it is not possible to state with certainty that interference will occur from specific installations. If this device has caused damaging interference to radio or TV signals (simply turn the device on and off to check if such interference is caused by the device), we recommend that you fix the interference using the following methods: eadjust the direction or location of the antenna. Increase the distance between this device and the receiver. Consult your local dealer or an experienced radio/tv technician. Warning: Making changes or modifications to the device without the permission from an authorized dealer may void the warranty of this device. 4 Safety Information

5 WEEE Information for users applicable in European Union countries. The symbol on the product or its packaging signifies that this product has to be disposed separately from ordinary household wastes at its end of life. Please kindly be aware that this is your responsibility to dispose electronic equipment at recycling centers so as to help conserve natural resources. Each country in the European Union should have its collection centers for electrical and electronic equipment recycling. For information about your recycling drop off area, please contact your local related electrical and electronic equipment waste management authority or the retailer where you bought the product. Hg amp Disposal AMP(S) inside this product contain mercury and must be recycled or disposed of according to local, state, or federal laws. For more information, contact the electronic industries alliance at for lamp specific disposal information check Vermont Hg directive Title 10: Conservation and Development Chapter 164: COMPEHENSIVE MECUY MANAGEMENT abeling of mercury-aided products Contains Mercury, Dispose of Properly Safety Information 5

6 Precautions CAUTION ISK OF EECTIC SHOCK DO NOT OPEN Symbols used in this manual This icon indicates the existence of a potential hazard that could result in personal injury or damage to the product. This icon indicates important operating and servicing information. Notice ead this User Manual carefully before using the CD display and keep it for future reference. The product specifications and other information provided in this User Manual are for reference only. All information is subject to change without notice. Updated content can be downloaded from our web site at To register online, go to To protect your rights as a consumer, do not remove any stickers from the CD display. Doing so may affect the determination of the warranty period. Cautions When Setting Up Do not place the CD display near heat sources, such as a heater, exhaust vent, or in direct sunlight. Do not cover or block the ventilation holes in the housing. Place the CD display on a stable area. Do not place the CD display where it may subject to vibration or shock. Place the CD display in a well-ventilated area. Do not place the CD display outdoors. Do not place the CD display in a dusty or humid environment. Do not spill liquid or insert sharp objects into the CD display through the ventilation holes. Doing so may cause accidental fire, electric shock or damage the CD display. 6 Precautions

7 Cautions When Using Use only the power cord supplied with the CD display. The power outlet should be installed near the CD display and be easily accessible. If an extension cord is used with the CD display, ensure that the total current consumption plugged into the power outlet does not exceed the ampere rating. Do not allow anything to rest on the power cord. Do not place the CD display where the power cord may be stepped on. If the CD display will not be used for an indefinite period of time, unplug the power cord from the power outlet. To disconnect the power cord, grasp and pull by the plug head. Do not tug on the cord; doing so may cause fire or electric shock. Do not unplug or touch the power cord with wet hands. Cleaning and Maintenance The CD display comes with NeoV TM Optical Glass. Use a soft cloth lightly moistened with a mild detergent solution to clean the glass surface and the housing. Do not rub or tap the surface of the glass with sharp or abrasive items such as a pen or screwdriver. This may result in scratching the surface of the glass. Do not attempt to service the CD display yourself, refer to qualified service personnel. Opening or removing the covers may expose you to dangerous voltage or other risks. Warning: Unplug the power cord from the power outlet and refer to qualified service personnel under the following conditions: When the power cord is damaged. If the CD display has been dropped or the housing has been damaged. If the CD display emits smoke or a distinct odor. Precautions 7

8 Notice for the CD Display In order to maintain the stable luminous performance, it is recommended to use low brightness setting. Due to the lifespan of the lamp, it is normal that the brightness quality of the CD display may decrease with time. When static images are displayed for long periods of time, the image may cause an imprint on the CD display. This is called image retention or burn-in. To prevent image retention, do any of the following: Set the CD display to turn off after a few minutes of being idle. Use a screen saver that has moving graphics or a blank white image. Execute the Anti-Burn-In function of the CD display. See Settings, Anit-Burn-In section. Switch desktop backgrounds regularly. Adjust the CD display to low brightness settings. Turn off the CD display when the system is not in use. Things to do when the CD display shows image retention: Turn off the CD display for extended periods of time. It can be several hours or several days. Use a screen saver and run it for extended periods of time. Use a black and white image and run it for extended periods of time. When the CD display is moved from one room to another or there is a sudden change from low to high ambient temperature, dew condensation may form on or inside the glass surface. When this happens, do not turn on the CD display until the dew disappears. Due to humid weather conditions, it is normal for mist to form inside the glass surface of the CD display. The mist will disappear after a few days or as soon as the weather stabilizes. There are millions of micro transistors inside the CD display. It is normal for a few transistors to be damaged and to produce spots. This is acceptable and is not considered a failure. 8 Precautions

9 1. Product Description 1.1 Package Contents When unpacking, check if the following items are included in the package. If any of them is missing or damaged, contact your dealer. CD display User Manual emote control Power cord -D cable cable Audio cable USB cable Note: The pictures are for reference only. Actual items may vary upon shipment. Chapter 1: Product Description 9

10 AC S-232C COMPONENT DC PC S-VIDEO CVBS V 50-60Hz 2 2 AUDIO 1 1 Pr2 Pr1 Pb2 VIDEO Pb1 Y2 Y1 12V Max 350mA AUDIO TOUCH SCEEN Y/C AUDIO VIDEO 2 VIDEO 1 AUDIO AC S-232C COMPONENT DC PC S-VIDEO CVBS V 50-60Hz 2 2 AUDIO 1 1 Pr2 Pr1 Pb2 VIDEO Pb1 Y2 Y1 12V Max 350mA AUDIO TOUCH SCEEN Y/C AUDIO VIDEO 2 VIDEO 1 AUDIO 1.2 Wall Mounting Installation Preparation Wall Mounting 1 emove the base stand and handles (if necessary). See procedures below. 2 Wall mount the CD display. Screw the mounting bracket to the VESA holes at the rear of the CD display. 600mm 400mm Note: To protect the glass panel, place a towel or soft cloth before laying the CD display down. 400mm 200mm emoving the Base Stand 1 ay the CD display face down on a flat even surface. 2 emove the four screws securing the base stand from the CD display. 3 ift to detach the base stand emoving the Handles 1 ay the CD display face down on a flat even surface. 2 Unscrew to remove each handle from the CD display. Note: Take measures to prevent the CD display from falling down and lessen possible injury and damage to the display in case of earthquakes or other disasters. Use only the 400 x 200 mm wall mount kit recommended by AG Neovo. Secure the CD display on a solid wall strong enough to bear its weight. 10 Chapter 1: Product Description

11 AUTO POWE 1.3 CD Display Overview Front View and Keypad Buttons Keypad Display screen The CD display screen is protected by NeoV TM Optical Glass ED indicator Green - Power on Amber - Standby mode Off - Power off emote control sensor (See page 13.) 10 AUTO POWE SOUCE Press repeatedly to select the input signal source. MENU Press to display the OSD menu. Press again to hide the OSD menu. UP Press repeatedly to select PIP option. During OSD menu selection, press to move up a menu or submenu. DOWN Press to swap the PIP main and sub picture. During OSD menu selection, press to move up a menu or submenu EFT Press to decrease the volume. During OSD menu selection, press to adjust the settings. IGHT Press to increase the volume. During OSD menu selection, press to select an option and adjust the settings. AUTO For input signal source, press to perform auto adjustment. For video input signals, press to perform screen freeze. During OSD menu selection, press to close the OSD menu or exit a submenu. 11 POWE Press to turn the power on or off. Chapter 1: Product Description 11

12 AC S-232C COMPONENT DC PC S-VIDEO CVBS V 50-60Hz 2 1 AUDIO 2 1 Pr2 Pr1 Pb2 VIDEO Pb1 Y2 Y1 12V Max 350mA AUDIO TOUCH SCEEN Y/C AUDIO VIDEO 2 VIDEO 1 AUDIO ear View AC S-232C COMPONENT PC DC 2 2 Pr2 Pb2 Y2 AUDIO S-VIDEO CVBS AUDIO VIDEO Y/C AUDIO VIDEO 2 VIDEO 1 AUDIO TOUCH SCEEN 1 1 Pr1 Pb1 Y AC power input 6 Audio port Use to connect the power cord. Use to connect an audio cable for the PC s audio input. 2 S-232 connector 7 connector Use to connect S-232 cables to connect multiple displays. Use to connect a PC using a cable for analogue input signal. 3 COMPONENT Audio and Video connectors (2) Use to connect component cables for YPbPr input signal. 8 connector Use to connect a PC using cable for digital input signal. 4 DC power output 9 S-Video connector (2) Use for DC power output. Use to connect AV cables for the S-Video signal. 5 USB port (for touch screen) Use to connect a USB cable for the PC s touch screen module. 10 COMPOSITE Audio and Video connectors (2) Use to connect composite cables for CVBS signal. 12 Chapter 1: Product Description

13 1.4 emote Control emote Control Buttons Power Key ock 5 CVBS 1 YPbPr1 S-Video CVBS 2 YPbPr2 3 UP Volume 12 7 eft Menu ight 8 13 Down Mute 1 POWE button Press to turn the monitor on or off. 7 Navigation button Press navigate through the OSD menu and adjust the settings. 2 CVBS1 button Press to select CVBS1 as the input signal. 8 MENU button Press to display the OSD menu. Press again to hide the OSD menu. 3 CVBS2 button Press to select CVBS2 as the input signal. 9 ock button Press to lock the OSD menu YPbPr1 button Press to select YPbPr1 as the input signal. YPbPr2 button Press to select YPbPr2 as the input signal. S-Video button Press to select S-Video as the input signal button Press to select as the input signal. button Press to select as the input signal. Volume buttons Press + to increase volume. Press - to decrease volume. MUTE button Press to mute volume. Chapter 1: Product Description 13

14 Power CVBS 1 CVBS 2 eft YPbPr1 YPbPr2 UP Menu Down S-Video ight Key ock Volume Mute Installing the emote Control Batteries 1 Turn the remote control upside down. 2 Press and hold the lock tab then pull the battery compartment out of the slot. 3 Place the battery on the battery compartment. 4 Push the battery compartment back into the slot until it clicks into place. C2025 ithium Battery 3V Notes about the battery: Do not leave the remote control in an extremely hot or humid place. Do not place the remote control in direct sunlight. Do not attempt to charge, short-circuit, heat, or burn the battery. If the remote control will not be used for a long period of time, remove the battery. eplace only with C2025 ithium battery, 3V. Dispose used battery according to the local disposal regulations emote Control Signal The remote control has an operating range of approximately 10 m. Aim the remote control directly at the remote sensor to ensure accuracy. 30 o Note: Make sure that the battery is sufficient to ensure optimum remote control performance. 14 Chapter 1: Product Description

15 AC S-232C COMPONENT DC PC S-VIDEO CVBS V 50-60Hz 2 1 AUDIO 2 1 Pr2 Pr1 Pb2 VIDEO Pb1 Y2 Y1 12V Max 350mA AUDIO TOUCH SCEEN Y/C AUDIO VIDEO 2 VIDEO 1 AUDIO 2. Making Connections 2.1 Connecting the AC Power 1 Connect the power cord to the AC power input at the rear of the CD display. 2 Connect the plug to a power outlet or a power supply. AC Caution: Make sure that the CD display is not connected to the power outlet before making any connections. Connecting cables while the power in ON may cause electric shock or personal injury. Caution: When unplugging the power cord, hold the power cord by the plug head. Never pull by the cord. Chapter 2: Making Connections 15

16 AC S-232C COMPONENT DC PC S-VIDEO CVBS V 50-60Hz 2 1 AUDIO 2 1 Pr2 Pr1 Pb2 VIDEO Pb1 Y2 Y1 12V Max 350mA AUDIO TOUCH SCEEN AC S-232C COMPONENT DC PC S-VIDEO CVBS V 50-60Hz 2 1 AUDIO 2 1 Pr2 Pr1 Pb2 VIDEO Pb1 Y2 Y1 12V Max 350mA AUDIO TOUCH SCEEN Y/C AUDIO Y/C VIDEO 2 AUDIO VIDEO 1 VIDEO 2 AUDIO VIDEO 1 AUDIO 2.2 Connecting Input Source Signals Connecting a Computer Using Cables Connect one end of a D-sub cable to the connector of the CD display and the other end to the D-sub connector of the computer. PC Using Cables Connect one end of a cable to the connector of the CD display and the other end to the connector of the computer. PC 16 Chapter 2: Making Connections

17 AC S-232C COMPONENT DC PC S-VIDEO CVBS V 50-60Hz 2 1 AUDIO 2 1 Pr2 Pr1 Pb2 VIDEO Pb1 Y2 Y1 12V Max 350mA AUDIO TOUCH SCEEN Y/C AUDIO VIDEO 2 VIDEO 1 AUDIO Using USB Cables (for touch screen) After connecting the CD display to the computer using either or connection, connect the supplied USB cable to install the device driver and use the touch screen module. Connect the mini-usb end of the USB cable to USB port of the CD display and the other end to the USB port of the computer. PC AUDIO TOUCH SCEEN See page 27 for instructions on how to install the touch screen driver. Chapter 2: Making Connections 17

18 AC S-232C COMPONENT DC PC S-VIDEO CVBS V 50-60Hz 2 1 AUDIO 2 1 Pr2 Pr1 Pb2 VIDEO Pb1 Y2 Y1 12V Max 350mA AUDIO TOUCH SCEEN AC S-232C COMPONENT DC PC S-VIDEO CVBS V 50-60Hz 2 1 AUDIO 2 1 Pr2 Pr1 Pb2 VIDEO Pb1 Y2 Y1 12V Max 350mA AUDIO TOUCH SCEEN Y/C Y/C AUDIO AUDIO VIDEO 2 VIDEO 2 VIDEO 1 VIDEO 1 AUDIO AUDIO Connecting a Camera or Video Device Using CVBS Cables Connect one end of a CVBS cable to the COMPOSITE connectors of the CD display and the other end to the COMPOSITE connectors of your device. For audio input, connect an CA cable to the audio in connector of the CD display and the audio out connector of your device. CVBS VIDEO 2 VIDEO 1 AUDIO or Using YPbPr Cables Connect one end of a YPbPr cable to the COMPONENT connectors of the CD display and the other end to the COMPONENT connectors of your device. For audio input, connect an CA cable to the audio in connector of the CD display and the audio out connector of your device. COMPONENT 2 2 Pr2 Pb2 Y2 AUDIO VIDEO 1 1 Pr1 Pb1 Y1 or 18 Chapter 2: Making Connections

19 AC S-232C COMPONENT DC PC S-VIDEO CVBS V 50-60Hz 2 1 AUDIO 2 1 Pr2 Pr1 Pb2 VIDEO Pb1 Y2 Y1 AUDIO TOUCH SCEEN AC S-232C COMPONENT DC PC S-VIDEO CVBS V 50-60Hz 2 1 AUDIO 2 1 Pr2 Pr1 Pb2 VIDEO Pb1 Y2 Y1 12V Max 350mA AUDIO TOUCH SCEEN 12V Max 350mA Y/C AUDIO Y/C VIDEO 2 AUDIO VIDEO 1 VIDEO 2 AUDIO VIDEO 1 AUDIO Using S-Video Cables Connect one end of an S-Video cable to the S-VIDEO connector of the CD display and the other end to the S-VIDEO connector of your device. For audio input, connect an CA cable to the audio in connector of the CD display and the audio out connector of your device. S-VIDEO Y/C AUDIO or 2.3 Connecting a Stereo Amplifier To amplify the sound output, connect a stereo amplifer to the CD display. Connect an CA cable to the audio out connector of the CD display and to the audio in connector of a stereo amplifier. CVBS AUDIO Chapter 2: Making Connections 19

20 AC S-232C COMPONENT DC PC S-VIDEO CVBS V 50-60Hz 2 1 AUDIO 2 1 Pr2 Pr1 Pb2 VIDEO Pb1 Y2 Y1 12V Max 350mA AUDIO TOUCH SCEEN Y/C AUDIO VIDEO 2 VIDEO 1 AUDIO Connecting an Audio Device Connect one end of an audio cable to the audio port at the rear of the CD display and the other end to the audio out port of the computer. PC AUDIO 20 Chapter 2: Making Connections

21 AC S-232C COMPONENT DC PC S-VIDEO CVBS V 50-60Hz 2 1 AUDIO 2 1 Pr2 Pr1 Pb2 VIDEO Pb1 Y2 Y1 12V Max 350mA AUDIO TOUCH SCEEN Y/C AUDIO VIDEO 2 VIDEO 1 AUDIO AC S-232C COMPONENT DC PC S-VIDEO CVBS V 50-60Hz 2 1 AUDIO 2 1 Pr2 Pr1 Pb2 VIDEO Pb1 Y2 Y1 12V Max 350mA AUDIO TOUCH SCEEN Y/C AUDIO VIDEO 2 VIDEO 1 AUDIO 2.4 Connecting Multiple CD Displays Use the S-232 connection to connect a series of CD displays to form a daisy chain. With this connection, the output of one computer can be shown on multiple displays at the same time. A maximum of 254 displays can be connected together. S-232C S-232C 1 Connect the female end of an S-232 cable to the S-232 port of the computer and connect the male end to the S-232 port of the display. 2 Connect the female end of another S-232 cable to the S-232 of the last connected display and the male end to the S-232 of the next display. 3 epeat step 2 to connect more CD displays. 4 Configure the connection using the Other Setting > S-232C menu. See page 48. Note: S-232 cables are not included in the package and are sold separately. Contact your dealer to purchase one. If an CD display in the series is turned off, the succeeding displays still receive the PC input signal. However, if the power cord of that CD display is unplugged from the power outlet, all succeeding displays also lose the signal. To ensure compatibility, use only AG Neovo displays. Chapter 2: Making Connections 21

22 AUTO POWE 3. Using the CD Display 3.1 Turning on the Power Using the Keypad 1 Plug the power cord to a power outlet or power supply. 2 Press the POWE button on the keypad to turn the CD display on. The ED indicator turns GEEN. POWE button When the CD display is turned on, press the POWE button to turn the CD display off. The ED indicator goes off Using the emote Control Press the POWE button on the remote control to turn the CD display on. Power CVBS 1 YPbPr1 S-Video Key ock The ED indicator turns GEEN. Press the POWE button again to turn the CD display off. The ED indicator goes off. CVBS 2 eft YPbPr2 UP Menu Down ight Volume Mute Note: The CD display still consumes power as long as the power cord is connected to the power outlet. Disconnect the power cord to completely cut off power. 22 Chapter 3: Using the CD Display

23 AUTO POWE 3.2 Selecting the Input Source Signal Using the Keypad SOUCE button 1 Press the SOUCE button on the keypad. The input signal screen is displayed on screen. The highlighted item shows the current input source signal. Notes: After selecting an input source signal, the input source signal message appears on the screen briefly. For example, CVBS1 is selected the following message is displayed. D - S U B D V I CVBS1 PUT C V B S 1 C V B S 2 S - V I D E O Y P b P r 1 Y P b P r 2 2 Press the SOUCE button repeatedly until the desired input source signal is highlighted. If the selected input source signal is not connected to the CD display or is turned off, the no signal message is displayed on the screen. NO SIGNA 3 Press to select the input source signal. If the resolution or the graphics card of the connected computer is set to high, the input out of range message is displayed Using the emote Control PUT SIGNA OF ANGE Power Key ock CVBS 1 YPbPr1 S-Video Press the desired input source signal button to select the source. CVBS 2 YPbPr2 UP Volume eft Menu ight Down Mute Chapter 3: Using the CD Display 23

24 AUTO POWE 3.3 Adjusting the Volume Using the Keypad 1 Press either or to call out the volume bar. 2 Press to increase volume. Press to decrease volume. VOUME buttons Using the emote Control Power Key ock CVBS 1 CVBS 2 YPbPr1 YPbPr2 S-Video On the remote control, press increase volume. Vo lume Vo lume to UP Volume Press to decrease volume. eft Menu ight Down Mute 3.4 Muting the Volume On the remote control, press to mute volume. The Mute message is displayed on the screen briefly. Press Mute again or the volume keys to cancel mute. Mute 24 Chapter 3: Using the CD Display

25 3.5 ocking the OSD Menu ock the OSD menu to protect the CD display from unauthorised users or from accidentally pressing the keypad or the remote control buttons. To lock the OSD, press and hold the keypad buttons listed below for at least 5 seconds or until the message appears. OSD OCK When the OSD is locked, all keypad and remote control buttons are inactivated. Type of OSD ock ock Operation Unlock Operation ock all buttons Press and hold and for 5 seconds. Press and hold and for 5 seconds or until the OSD menu appears. ock all buttons except the POWE button. Press and hold and for 5 seconds. Press and hold and for 5 seconds or until the OSD menu appears. Chapter 3: Using the CD Display 25

26 3.6 Using Picture-in-Picture (PIP) The Picture-in-Picture (PIP) feature allows viewing of more than one input source signal on the CD display PIP Options On the keypad or the remote control, press repeatedly to enable and scroll among the PIP options. Options are as follows: PIP On PIP Off PAP PAP 4:3 Info: PIP On: The sub source signal is displayed within the main source signal. PAP (Picture-and-Picture): The main source and the sub source signals are displayed side by side with equal display size. PAP 4:3 The main source and the sub source signals are displayed side by side, each with an aspect ration of 4:3. PIP Off: PIP function is disabled, only the main source signal is displayed PIP Swap The main and the sub source signals set in PIP Setting can be easily swapped using the keypad or the remote control. Main source Note: The main source and sub source signals can be set in PIP Settings, see page 43. Sub source Press to swap the main source and the sub source signals. See illustration below. Main source Sub source 26 Chapter 3: Using the CD Display

27 4. Touch Screen Properties 4.1 Installing the CD Display Driver To use the touch screen module of the CD display, the device driver must be installed to the computer first. The device driver supports Windows XP, Windows Vista, and Windows 7. efer to the applicable operating system below for installation instructions Windows XP Installation 1 Connect the CD display to your computer using the supplied USB cable (See page 17). 2 Windows detects the CD display and shows the screen below. Click Cancel. A message pops out from the system tray. 3 Insert the CD to the CD-OM of the computer. 4 Browser for the setup file, and double-click NextWindow_2500_Driver_ _Generic.exe to install the driver. 5 After running the setup file, the touch screen module is ready for use. Chapter 4: Touch Screen Properties 27

28 4.1.2 Windows 7 / Windows Vista Installation The following illustrations are based on Windows 7 operating system. However, similar steps apply to Windows Vista. 1 Connect the CD display to your computer using the supplied USB cable (see page 17). 2 Windows detects the CD display and shows the screen below. 3 Insert the CD to the CD-OM of the computer. 4 Browser for the setup file, and double-click NextWindow_2500_Driver_ _Generic.exe to install the driver. 5 When setup completes, a message pops out from the system tray to confirm the installation. The touch screen module is ready for use. Note: To get the latest driver and other product support, visit visit 28 Chapter 4: Touch Screen Properties

29 4.2 Using the Touch Screen The CD Display requires zero-pressure, users can use a finger, gloved hand, or any other pointer. The advanced optical sensor provides accurate touch response, therefore re-calibration is not needed Single-Touch vs. Multi-Touch The CD Display supports both multi-touch and single-touch functions. Single-touch allows users to touch the screen instead of using a mouse. Users can use a finger or a stylus as a pointing device. Multi-touch allows users to manipulate objects on screen using various sets of finger gestures such as the use of two fingers to stretch, zoom, or rotate. The availability of these functions depends on the operating system of the computer. Windows 7 supports multi-touch, while lower versions only support single-touch. Note: Touch screen module is not available when using the OSD (On Screen Display) menu. To adjust the settings, use the remote control or the keypad Finger Gestures By default, the CD display responds to the following standard point and click operations. To click, touch the screen. To drag, touch and move. To double-click, double-touch. To right-click, touch and hold. A circle appears on the screen followed by the options menu. Note: Multi-touch gestures are only applicable in Windows 7. To scroll, rotate, or zoom in a single-touch environment, touch the corresponding icons or scroll bars on the screen. Chapter 4: Touch Screen Properties 29

30 The following are multi-touch operations: To scroll up or down the screen, flick up or down. To go forward or back a page, such as in viewing pictures, flick to the left or right. To rotate, touch one point with your thumb, then move your index finger clockwise or counter-clockwise. To resize or move, touch one point with your thumb, then use the index finger to move. To zoom, pinch two fingers together then expand to zoom in. Or, expand two fingers on the screen, the pinch them together to zoom out Touch Screen Extras The touch screen module provides an on-screen keyboard for text entry. To activate the keyboard, touch and hold the edge of the keyboard, then move your finger to the center of the screen. To enter text, touch the keys as you would on a standard keyboard or set to handwriting mode to write characters on the screen. For more information about using the on-screen keyboard, touch Tools > Help. 30 Chapter 4: Touch Screen Properties

31 4.3 Windows Pen and Touch Settings The CD display is configured with default touch operations as discussed on page 29. It is recommended to retain these defaults. However, if desired, touch settings can be changed according to ones preference in Windows 7. To do this, follow the steps below: 1 Touch Start > Control Panel > Pen and Touch. 2 Browse the tabs and modify the desired settings. 3 Touch Apply to save and apply settings. Chapter 4: Touch Screen Properties 31