Schedule of Accreditation issued by United Kingdom Accreditation Service High Street, Feltham, Middlesex, TW13 4UN, UK

Transcription

1 21-47 High Street, Feltham, Middlesex, TW13 4UN, UK Royal & SunAlliance Insurance PlcTrading as:- RSA Engineering and 17 York Street Manchester M2 3RS Contact: Mr Richard Green Tel: +44 (0) Fax: +44 (0) Website: Inspection performed at/from the above address only DETAIL OF ACCREDITATION Field of Inspection Type and Range of Inspection Methods and Procedures Pressure Equipment Welding Procedures and Welder Approvals Major, Intermediate and Minor Pressure Systems Design Verification, New Construction and Inspection Verification and Approval Certification of written schemes of examination and in-service inspection RSA Procedure P31 and P38 referencing published national/ international standards for pressure equipment RSA Procedure P22 Pressure System Safety Regulations 2000 SI 2000, No 128 RSA Procedure P01 and P16 Power Presses In-service inspection Provision and Use of Work Regulations SI.1998 No 2306, Part IV (PUWER 98) RSA Procedure R027.1 to R043.4 Lifting Equipment In-service inspection Lifting Operations and Lifting Equipment Regulations 1998 (LOLER 98), SI.1998 No 2307 RSA Procedure R002.1 to R040.2 Local Exhaust Ventilation Plant (LEV) Initial Appraisal and In-service Inspection/Thorough Examination and Test of Engineering Controls Control of Substances Hazardous to Health Regulations 2002 Control of Substances Hazardous to Health Regulations (N.I.) 2003 RSA Procedure R017.1 to R017.4 END Assessment Manager: NH1 Page 1 of 8

2 and / or Inspection Essential requirements: The Carriage of Dangerous Goods & Use of Transportable Pressure Equipment Regulations 2009 (as amended) AND The Carriage of Dangerous Goods & Use of Transportable Pressure Equipment (Northern Ireland) Regulations 2010 (as amended). PART 3 of the Approved Derogations & Transitional Provisions. Intermediate inspection. Exceptional checks: UK road, and rail, tanks* constructed before 10/05/04. Metallic tanks. Vacuum-operated waste tanks. for substances of Class(s) 2, 3, 4, 5, 6, 8 & 9 VCA Procedures for Inspection & Testing of UK Tanks For substances of Class 3 Special case procedure I140 for hydraulic pressure testing with alternative fluids with a flashpoint >61 o C using: UN1202 UN1223 MOD Tanks for Class 3 substances MOD Test Fluids F-44: Turbine Fuel, Aviation F-54: Diesel Fuel F-76: Fuel Naval Distillate UK Road tanks for LPG * constructed in GB after 09/05/2004 or in NI after 31/07/06 to EN 12493, Annex C. pproval Supervision of construction UK Road tanks for LPG * constructed in GB after 9 th May 2004 or in NI after 31/07/06 to EN 12493, Annex C. Assessment Manager: NH1 Page 2 of 8

3 and / or Inspection Essential requirements: RID, ADR Chapter 6.8 Chapter 6.10 Intermediate inspection. Exceptional checks: pproval Tanks with shells of Metallic Materials* (chapter 6.8) Fixed tanks (road tanks) Tank wagons (rail tanks) Demountable tanks Tank containers Tank swap bodies Battery vehicles (road) Battery wagons (rail) MEGCs EN13530: 2002 EN14025: 2008 Vacuum Operated Waste Tanks* (chapter 6.10) for substances of Class(s) 3, 4, 5, 6, 8 & 9 For substances of Class 3 Special case procedure I140 for hydraulic pressure testing with alternative fluids with a flashpoint >61 o C using: UN1202 UN1223 MOD Tanks for Class 3 substances MOD Test Fluids F-44: Turbine Fuel, Aviation F-54: Diesel Fuel F-76: Fuel Naval Distillate Assessment Manager: NH1 Page 3 of 8

4 and / or Inspection Essential requirements: The Transportable Pressure Equipment Directive 2010/35/EU Article 12 of the Directive 2010/35/EU of the Annexes 2008/68/EC Intermediate inspection. Exceptional checks: Conformity assessment Conformity reassessment Supervision of construction Tanks with shells of Metallic Materials* (chapter 6.8) Fixed tanks (road tanks) Tank wagons (rail tanks) Demountable tanks Tank containers Tank swap bodies Battery vehicles (road) Battery wagons (rail) MEGCs EN13530: 2002 EN14025: 2008 PD5500: A2: 2010 ASME VIII: Div 1 ASME VIII: Div 2 for substances of Class 2 ADR, RID* (Chapter 6.2) Conformity assessment including: pproval Supervision of manufacture Periodic inspection, intermediate inspection, and exceptional checks Cryogenic vessels Transportable vacuum insulated, of not more than 1000 litres volume. EN1251-2:2000 P35 and 36 The Carriage of Dangerous Goods & Use of Transportable Pressure Equipment Regulations 2009 (as amended) AND The Carriage of Dangerous Goods & Use of Transportable Pressure Equipment (Northern Ireland) Regulations 2010 (as amended) The Merchant Shipping (Dangerous Goods and marine Pollutants) regulations 1997 ADR, RID* & IMDG Code Chapter 6.2 Conformity assessment including: pproval Supervision of manufacture Periodic inspection, intermediate inspection, and exceptional checks Cryogenic vessels Transportable vacuum insulated, of not more than 1000 litres volume. EN1251-2:2000 P35 and 36 Assessment Manager: NH1 Page 4 of 8

5 and / or Inspection Essential requirements: RID, ADR & IMDG Code, Chapter 6.7 Intermediate inspections. Exceptional checks: Portable Tanks* for substances of Class(s) 2, 3, 4, 5, 6, 8 & 9 IMO Res A.581 (14) pproval Supervision of construction EN13530: 2002 EN14025: 2008 PD5500: A2: 2010 ASME VIII: Div 1 ASME VIII: Div 2 IMDG Code, Chapter 6.7 pproval Supervision of construction Offshore tank-containers* MSC/Circ.860 EN : 2006 The Merchant Shipping (Dangerous Goods and marine Pollutants) regulations 1997 Intermediate inspections. Exceptional checks IMO Type 1,2,5 & 7 Portable tanks* IMO Type 4,6 & 8 Road tank vehicles* DSC/Circ.12 IMO Res A.581 (14) Note: The inspection of items marked thus * or ** are subject to legislative requirements including the appointment of persons to carry out inspections. Reference should be made to the VCA Dangerous Goods Office for information on this and listings of bodies recognised under UK legislation. END Assessment Manager: NH1 Page 5 of 8

6 Accreditation for the purpose of Notified Body Activity taking into account EA2/17 and relevant requirements of EN ISO/IEC & EN Essential requirements: Pressure Equipment Directive 97/23/EC implemented by; Pressure Equipment Regulations 1999 (SI 2001) Directive: Article 10:Annex III Regulation: 12 - Schedule 4 Modules A1, B, B1, C1, D, D1, E, E1, F, G, H, H1 Directive: Article 11 Regulation: 17 - Schedule 7 All descriptions of pressure equipment and assemblies covered by the Regulations. Issuing European Approval of Materials Directive: Annex I Regulations: Schedule Categories II III and IV Approval of permanent joining procedures and personnel Directive: Annex I Regulations: Schedule Categories III and IV Approval of personnel to carry out non-destructive test on permanent joints for pressure equipment Procedures Directive: Article 14 Regulation: 22 User Inspectorate Modules A1, C1, F, G All descriptions of pressure equipment and assemblies covered by the Regulations. Procedures Simple Pressure Vessels Directive 2009/105/EC Implemented by The Simple Pressure Vessels (Safety) Regulations 1991 (as amended) EC type-examination Directive: Article 10 Regulation 11 EC declaration of conformity Directive: Articles 12, 13 and 14 Regulation 13 EC verification Directive: Article 11 Regulation 12 Simple Pressure Vessels manufactured in series BS EN A2:2005 Assessment Manager: NH1 Page 6 of 8

7 Accreditation for the purpose of Notified Body Activity taking into account EA2/17 and relevant requirements of EN ISO/IEC & EN Essential requirements: Directive 95/16/EC implemented by; The Regulations 1997 (as amended) Directive: Annex V B Regulation: Schedule 5 B EC Type-examination Directive: Annex VI Regulation: Schedule 6 Final Inspection Directive: Annex X Regulation: Schedule 9 Unit verification Directive: Annex XIII Regulation: Schedule 12 Full quality assurance Directive: Annex XIV Regulation: Schedule 13 Production quality assurance Directive: Annex V A Regulation: Schedule 5 A Safety Components EC Type-examination Directive: Annex IX Regulation: Schedule 8 Safety Components Full quality assurance Directive: Annex VIII Regulation: Schedule 7 Safety Components Production quality assurance Assessment Manager: NH1 Page 7 of 8

8 Accreditation for the purpose of Notified Body Activity taking into account EA2/17 and relevant requirements of EN ISO/IEC & EN Essential requirements: Machinery Directive 2006/42/EC implemented by: Directive: Article 12 (3)b and (4)a :Annex IX Regulation: Schedule 2 Part 9 Annex IV item 17 Part 4 Item 17 The Supply of Machinery(Safety) Regulation 2008 (SI 1597) EC Type Examination Directive: Article 12 (3)c and (4)b :Annex X Regulation: Schedule 2 Part 10 Annex IV item 17 Part 4 Item 17 Full Quality Assurance Note: The inspection of items above are subject to legislative requirements including the appointment of bodies to carry out conformity assessment. Reference should be made to the relevant Government Departments BIS for information on this and listings of bodies recognised under UK legislation END Assessment Manager: NH1 Page 8 of 8